The GPT is the GPT timer found on i.MX SoCs.
This adds the missing GPT devicetree nodes. Also fixup the watchdog
register map size along the way. it's 0x1000, not 0x4000. This didn't
hurt before as the region was not occupied by another device, but now
overlaps with the GPT.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Similarly as it was done for mx6q, use a DT lookup in order to make maintainance
task for the clock devices easier.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add a second pinctrl group of pins for i2c2.
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add ecspi2 group of pins for imx51.
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The APF51Dev is a docking board for an APF51 SOM
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Allow AUD3 to be used as audio output from the audmux block.
Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Currently, all imx pinctrl drivers maintain a big array of struct
imx_pin_reg which hard-codes data like register offset and mux mode
setting for each pin function. Every time a new imx SoC support is
added, we need to add such a big mount of data. With moving to single
kernel build, it's only matter of time to be blamed on memory consuming.
With DTC pre-processor support in place, the patch moves all these data
into device tree by redefining the PIN_FUNC_ID in imxXX-pinfunc.h and
changing the PIN_FUNC_ID parsing code a little bit.
The pin id gets re-numbered based on mux register offset, or config
register offset if the pin has no mux register, so that kernel can
identify the pin id from register offsets provided by device tree.
As a bonus point of the change, those arbitrary magic numbers standing
for particular PIN_FUNC_ID in device tree sources are now replaced by
macros to improve the readability of dts files.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Replace /include/ (dtc) with #include (C pre-processor) for all imx DT
files, so that gcc -E handles the entire include tree, and hence any of
those files can #include some other file e.g. for constant definitions.
This allows future use of #defines and header files in order to define
names for various constants, such as pinctrl settings. Use of those
features will increase the readability of the device tree files.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add ARM Cortex A9 Performance Monitor Unit (PMU) support.
On i.MX6 a combined interrupt on hardware line #126 is used
(i.MX6 TRM: Performance Unit interrupt).
For more details see Documentation/devicetree/bindings/arm/pmu.txt
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
information. Also enable few HW errata workarounds for omap4.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=bKnC
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.10/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
From Tony Lindgren <tony@atomide.com>:
Changes needed for enabling SOC_BUS for the SoC revision
information. Also enable few HW errata workarounds for omap4.
* tag 'omap-for-v3.10/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (236 commits)
ARM: OMAP4: Enable fix for Cortex-A9 erratas
ARM: OMAP2+: Export SoC information to userspace
ARM: OMAP2+: SoC name and revision unification
ARM: OMAP2+: Move common part of late init into common function
Includes an update to Linux 3.9-rc6
Conflicts:
arch/arm/mach-omap2/cclock44xx_data.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This branch includes major development on the core Tegra SoC support code
in the mach-tegra directory:
* SMP support for Tegra114.
* Exposes SoC chip ID and revision through standard sysfs files.
* System-level suspend/resume for Tegra20/30. At present, this only
supports "LP2" mode (CPU power-down), but provides the basis to
implement "LP0"/"LP1" (various levels of core/chip power-down) in the
hopefully near future.
* A minor cleanup of a duplicate include, which was introduced in this
branch.
This branch is based on the previous cleanup pull request.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=1KXE
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.10-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From Stephen Warren <swarren@wwwdotorg.org>:
ARM: tegra: core SoC support development
This branch includes major development on the core Tegra SoC support code
in the mach-tegra directory:
* SMP support for Tegra114.
* Exposes SoC chip ID and revision through standard sysfs files.
* System-level suspend/resume for Tegra20/30. At present, this only
supports "LP2" mode (CPU power-down), but provides the basis to
implement "LP0"/"LP1" (various levels of core/chip power-down) in the
hopefully near future.
* A minor cleanup of a duplicate include, which was introduced in this
branch.
This branch is based on the previous cleanup pull request.
* tag 'tegra-for-3.10-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra: pm: remove duplicated include from pm.c
ARM: tegra: cpuidle: remove redundant parameters for powered-down mode
ARM: tegra: pm: add platform suspend support
ARM: dt: tegra: add bindings of power management configurations for PMC
ARM: tegra: irq: add wake up handling
gpio: tegra: add gpio wakeup source handling
ARM: tegra: moving the CPU power timer function to PMC driver
ARM: tegra: add clock source of PMC to device trees
ARM: tegra: add speedo-based process id for Tegra114
ARM: tegra: expose chip ID and revision
ARM: tegra: bring up secondary CPU for Tegra114
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* Clean up timer code and move it into drivers/clocksource
* Clean up icoll code and move it into drivers/irqchip
* Clean up clock code to not include <mach/*> headers
* Clean up rtc-stmp3xxx, mxs-lradc and mxs-saif to not include <mach/*>
headers
* Clean up mach-mxs code to get it prepared for multiplatform support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRYnwxAAoJEFBXWFqHsHzOs34H/iSLBv6I+f6oPubu52kJz6fP
ctZPm6ZJPUKIiyVLLcmMf9kMr3h0wWH3XOBDzPdSj0Wtyb+rbpb/qa0jOg2EwZOs
2g+7LpehX2BgqKzdBPQEBC94NuU81F0X7SDZe0YechEWZY1VBGjaDnPso+Ugs23A
7hpjRHAOjd8gnJvkqU/uLKkbJiRX/pvXDcxkRhu15HsA9v6m18Elpq4FNw1QccLd
06o2M8aVvSL4IYy4Eh8lheUZrPNuyapG3TTjzhbYlPZtvXijFEFWniAQWyq5eGdg
3aiVbv3lCWYyJzFhmv9n6WYGqHthpnxej9ZMsREa1OVjmViDzSTda6vlhJvBOHQ=
=neCB
-----END PGP SIGNATURE-----
Merge tag 'mxs-cleanup-3.10' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/cleanup
From Shawn Guo <shawn.guo@linaro.org>:
The mxs cleanup for 3.10:
* Clean up timer code and move it into drivers/clocksource
* Clean up icoll code and move it into drivers/irqchip
* Clean up clock code to not include <mach/*> headers
* Clean up rtc-stmp3xxx, mxs-lradc and mxs-saif to not include <mach/*>
headers
* Clean up mach-mxs code to get it prepared for multiplatform support
* tag 'mxs-cleanup-3.10' of git://git.linaro.org/people/shawnguo/linux-2.6: (26 commits)
clocksource: mxs_timer: Add semicolon at end of line
ARM: mxs: remove unused headers
ARM: mxs: merge imx23 and imx28 into one machine_desc
ARM: mxs: remove common.h
ARM: mxs: move mxs_get_ocotp() into mach-mxs.c
ARM: mxs: remove mm.c
ARM: mxs: use debug_ll_io_init for low-level debug
ARM: mxs: get ocotp base address from device tree
ARM: mxs: remove system.c
ARM: mxs: get reset address from device tree
ARM: mxs: remove empty hardware.h
ASoC: mxs-saif: remove mach header inclusion
iio: mxs-lradc: remove unneeded mach header inclusion
rtc: stmp3xxx: use stmp_reset_block() instead
clk: mxs: remove the use of mach level IO accessor
clk: mxs: get base address from device tree
ARM: mxs: remove unneeded mach-types.h inclusion
ARM: mxs: move icoll driver into drivers/irqchip
ARM: mxs: call stmp_reset_block() in icoll
ARM: mxs: get icoll base address from device tree
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRWLTrAAoJEHm+PkMAQRiGe8oH/iMy48mecVWvxVZn74Tx3Cef
xmW/PnAIj28EhSPqK49N/Ow6AfQToFKf7AP0ge20KAf5teTq95AY+tH74DAANt8F
BjKXXTZiR5xwBvRkq7CR5wDcCvEcBAAz8fgTEd6SEDB2d2VXFf5eKdKUqt1avTCh
Z6Hup5kuwX+ddtwY2DCBXtp2n6fL0Rm5yLzY1A3OOBye1E7VyLTF7M5BR603Q44P
4kRLxn8+R7jy3hTuZIhAeoS8TKUoBwVk7DmKxEzrhTHZVOmvwE9lEHybRnIyOpd/
k1JnbRbiPsLsCVFOn10SQkGDAIk00lro3tuWP2C1ljERiD/OOh5Ui9nXYAhMkbI=
=q15K
-----END PGP SIGNATURE-----
Merge tag 'v3.9-rc5' into next/cleanup
This is a dependency for the mxs/cleanup branch.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This branch includes various cleanup of the core Tegra support.
* Unification of the separate board-dt-tegra*.c files into a single
tegra.c, now that everything is DT-driven and basically identical.
* Use of_clk_get() in the Tegra clocksource driver so that clocks are
described in DT rather than hard-coding clock names.
* Some cleanup of the PMC-related code, with the aim that the PMC
"driver" contains more of the code that touches PMC registers, rather
than spreading PMC register accesses through other files.
* Conversion of the "PMC" driver to acquire resources describe in device
tree rather than hard-coding them.
* Use of common code for the CPU sleep TLB invalidation.
This branch is based on the previous fixes pull request.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3GM9
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.10-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup
From Stephen Warren <swarren@wwwdotorg.org>:
ARM: tegra: cleanup
This branch includes various cleanup of the core Tegra support.
* Unification of the separate board-dt-tegra*.c files into a single
tegra.c, now that everything is DT-driven and basically identical.
* Use of_clk_get() in the Tegra clocksource driver so that clocks are
described in DT rather than hard-coding clock names.
* Some cleanup of the PMC-related code, with the aim that the PMC
"driver" contains more of the code that touches PMC registers, rather
than spreading PMC register accesses through other files.
* Conversion of the "PMC" driver to acquire resources describe in device
tree rather than hard-coding them.
* Use of common code for the CPU sleep TLB invalidation.
This branch is based on the previous fixes pull request.
* tag 'tegra-for-3.10-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra: use setup_mm_for_reboot rather than explicit pgd switch
ARM: tegra: replace the CPU power on function with PMC call
ARM: tegra: pmc: add power on function for secondary CPUs
ARM: tegra: pmc: convert PMC driver to support DT only
ARM: tegra: fix the PMC compatible string in DT
ARM: tegra: pmc: add specific compatible DT string for Tegra30 and Tegra114
ARM: tegra: refactor tegra{20,30}_boot_secondary
clocksource: tegra: move to of_clk_get
ARM: tegra: Unify Device tree board files
ARM: tegra: Rename board-dt-tegra20.c to tegra.c
ARM: tegra: Unify tegra{20,30,114}_init_early()
Conflicts:
drivers/clocksource/tegra20_timer.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This branch contains a variety of small build and run-time fixes that
weren't important enough for 3.9.
* Enable CPU errata WARs in secondary reset handler as a preparation
for multi-platform support, and a related fix.
* Don't touch DBLGAR in reset/resume handlers, so enable the code to
run on A15 cores.
* Minor build fixes.
* A fix to the Tegra clock driver.
* Some error-handling fixes.
This branch is based on the previous fixes-for-mmc pull request.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=5rB4
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.10-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/fixes-non-critical
From Stephen Warren <swarren@wwwdotorg.org>:
ARM: tegra: minor fixes
This branch contains a variety of small build and run-time fixes that
weren't important enough for 3.9.
* Enable CPU errata WARs in secondary reset handler as a preparation
for multi-platform support, and a related fix.
* Don't touch DBLGAR in reset/resume handlers, so enable the code to
run on A15 cores.
* Minor build fixes.
* A fix to the Tegra clock driver.
* Some error-handling fixes.
This branch is based on the previous fixes-for-mmc pull request.
* tag 'tegra-for-3.10-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra: powergate: Don't error out if new state == old state
ARM: tegra: Export tegra_powergate_sequence_power_up()
memory: tegra30: Fix build error w/o PM
ARM: tegra: fix ignored return value of regulator_enable
ARM: tegra: fix the logical detection of power on sequence of warm boot CPUs
ARM: tegra: Fix unchecked return value
ARM: tegra: don't unlock MMIO access to DBGLAR
clk: tegra: No 7.1 super clk dividers on Tegra20
ARM: tegra: remove save/restore of CPU diag register
ARM: tegra: add CPU errata WARs to Tegra reset handler
ARM: dts: tegra: fix the activate polarity of cd-gpio in mmc host
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* A couple imx35 clock fixes for regressions caused by common clock
framework conversion. The admux and iomux get disabled by common
clock framework late initcall, and hence causes problems.
* Add missing twd clock lookup in device tree. This becomes required
since commit bd60345 (ARM: use device tree to get smp_twd clock)
forces all DT boot to find lookup from device tree.
* Fix imx6q ldb_di clock parents mismatch per reference manual.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRZAZBAAoJEFBXWFqHsHzOy60H/0RIxFO1TSQVVPTuJRtHr9qk
BtszcLOwiRbWipuG1OiosEKXMeOXjAPtOG8P9tReC/oJN4WL5CmGW3PrPQ/9DEbZ
OTYVPhgmGKDB/2n5BVvvTDISTovvlQRju4ht+70j1BnAlpbzGLbKMG4o6zHOROoh
d15dqg/Ny1ovsCvva2ODbwRtBkBaBqDC+RGqNPrhTN7WSk+nv6yITYZCREI1mjGH
RG7B62hn+1aD6tMdigFu9xS4vTkHXjFC0AVEixBEi3iWqofSz3Cb6Zq4MpRGNXGZ
o/tfc4/2q6uF/UEpTQJDhYbHjwesySsIwdu4vsvI2lh9EGqUgyC3YE+VbDwOeGE=
=tztW
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.9-5' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo <shawn.guo@linaro.org>:
The imx fixes for 3.9, take 5:
* A couple imx35 clock fixes for regressions caused by common clock
framework conversion. The admux and iomux get disabled by common
clock framework late initcall, and hence causes problems.
* Add missing twd clock lookup in device tree. This becomes required
since commit bd60345 (ARM: use device tree to get smp_twd clock)
forces all DT boot to find lookup from device tree.
* Fix imx6q ldb_di clock parents mismatch per reference manual.
* tag 'imx-fixes-3.9-5' of git://git.linaro.org/people/shawnguo/linux-2.6: (217 commits)
ARM i.MX6: Fix ldb_di clock selection
ARM: imx: provide twd clock lookup from device tree
ARM: imx35 Bugfix admux clock
ARM: clk-imx35: Bugfix iomux clock
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add SMSC ethernet support to the bockw board.
This pull request is based on a merge of:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git renesas-soc-r8a7778-for-v3.10
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git renesas-boards3-for-v3.10
The reason for merging with renesas-soc-r8a7778-for-v3.10 is
to provide pre-requisite SoC code to configure IRQ pins for the
SMSC ethernet.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJRXjzZAAoJENfPZGlqN0++PfsP+wXKEGnS47efqfh/wgNQTiJP
bc7ottBOfXkiLhz1NB3LMw1c9mNF+n57wetiED9l0BR8gwGi7X6Fespa024lIp32
Sw/FSHnAdUwB7MD+uQUrDeN2+UUplR+0aSY7vmcAQ7XHbuytB1BylQrA2sxQA1NY
O27J5s6IjZNWSX2FzUPmEygDhUcikkAPbC6IfmfEIJPoLJ9Li6NePsuPc2sXokby
kJkbqhnL20Ja9Vv8aKuSJO/4IYQHCkk0jAvaJRDctlWHMlPEBqsx7DXFRSmzTc7F
Wm4uySM1VrVpCoGDkQtd+zbatVJOOuKzq0kN5g0LDe73hpHrQx8pJyFdZtxPD9BA
ctm3E+p6Wx8Zna2WtQgsNRjkRPCz5kcwqCdmnCLykOTtxs8lwnRUn3nN3qL0R+uu
KeIRsxwgL9O67FyrZk4WW9On0Qob2vd66ktCF12FCTlX3vYIQR0vFAQ8VlF2OeZl
S2VJ6+FM8N5jUzDFoOzYTUOXcskomUxPop93HbRDho/bgLhOba9cD9tSep/4p7ZZ
s4oz20WSBUvszK7He8kGiTn8vwR/1mEwQPyP1eZh/hSxWGxdqdTQ5ZcT4IA0Hbe9
CFZ9qiRBzOjBhDEgYmKYo3BN9Yk7WVB9ILWa7xsD05yskcaA+ps/Om0/81i75iCx
n1PDVuc/A9H1F5REQaM7
=kjpJ
-----END PGP SIGNATURE-----
Merge tag 'renesas-boards-bockw-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/boards2
From Simon Horman <horms+renesas@verge.net.au>:
Renesas ARM-based SoC bockw board updates for v3.10
Add SMSC ethernet support to the bockw board.
This pull request is based on a merge of:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git renesas-soc-r8a7778-for-v3.10
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git renesas-boards3-for-v3.10
The reason for merging with renesas-soc-r8a7778-for-v3.10 is
to provide pre-requisite SoC code to configure IRQ pins for the
SMSC ethernet.
* tag 'renesas-boards-bockw-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: bockw: enable network settings on bootargs
ARM: shmobile: bockw: add SMSC ethernet support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
much all non-critical fixes for platform device initialization
that will be needed until we can drop the board-*.c files and
move to DT based boot.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=g9O/
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.10/board-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/boards
From Tony Lindgren <tony@atomide.com>:
Board related changes for v3.10 merge window. These are pretty
much all non-critical fixes for platform device initialization
that will be needed until we can drop the board-*.c files and
move to DT based boot.
* tag 'omap-for-v3.10/board-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: board-4430sdp: Provide regulator to pwm-backlight
ARM: OMAP: zoom: Use pwm stack for lcd and keyboard backlight
ARM: OMAP2+: omap2plus_defconfig: Add support for BMP085 pressure sensor
omap2+: Remove useless Makefile line
omap2+: Remove useless Makefile line
ARM: OMAP: RX-51: add missing regulator supply definitions for lis3lv02d
ARM: OMAP1: fix omap_udc registration
Includes an update to Linux 3.9-rc6
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This pull request enables CGROUPS in defconfig and also
cleans up mach-davinci to use IS_ENABLED() macro.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=JE9w
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.10/board' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/boards
From Sekhar Nori <nsekhar@ti.com>:
v3.10 board updates for DaVinci
This pull request enables CGROUPS in defconfig and also
cleans up mach-davinci to use IS_ENABLED() macro.
* tag 'davinci-for-v3.10/board' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: use is IS_ENABLED macro
ARM: davinci: defconfig: enable CGROUPS
Includes an update to v3.9-rc3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
While booting from device tree, imx6q used to provide twd clock lookup
by calling clk_register_clkdev() in clock driver. However, the commit
bd60345 (ARM: use device tree to get smp_twd clock) forces DT boot to
look up the clock from device tree. It causes the failure below when
twd driver tries to get the clock, and hence kernel has to calibrate the
local timer frequency.
smp_twd: clock not found -2
...
Calibrating local timer... 396.13MHz.
Fix the regression by providing twd clock lookup from device tree, and
remove the unused twd clk_register_clkdev() call from clock driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The pull request adds support for MMC/SD and regulator on DA850 EVM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=OjvJ
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.10/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/soc
From Sekhar Nori <nsekhar@ti.com>:
v3.10 DT updates for DaVinci
The pull request adds support for MMC/SD and regulator on DA850 EVM.
* tag 'davinci-for-v3.10/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: da850: override mmc DT node device name
ARM: davinci: da850: add mmc DT entries
mmc: davinci_mmc: add DT support
ARM: davinci: da850: add tps6507x regulator DT data
ARM: regulator: add tps6507x device tree data
Merged into soc branch rather than DT branch to avoid circular dependencies.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
a) adds support for eHRPWM clocks
b) Fix the way MMC/SD IP versions are communicated to driver
in preparation for DT support
c) Minor cleanup in debug-macro.S
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=ABW/
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.10/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/soc
From Sekhar Nori <nsekhar@ti.com>:
v3.10 SoC updates for DaVinci
a) adds support for eHRPWM clocks
b) Fix the way MMC/SD IP versions are communicated to driver
in preparation for DT support
c) Minor cleanup in debug-macro.S
* tag 'davinci-for-v3.10/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: remove test for undefined Kconfig macro
ARM: davinci: mmc: derive version information from device name
ARM: davinci: da850: add ECAP & EHRPWM clock nodes
ARM: davinci: clk framework support for enable/disable functionality
Includes an update to Linux 3.9-rc5
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In order to convert the Tegra MMC driver to using mmc_of_parse(), some
bugs in the Tegra device-tree content need to be fixed first; it's
currently wrong but unused, and mmc_of_parse() causes that data to be
used for the first time.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=G8rC
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.10-fixes-for-mmc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/dt
From Stephen Warren <swarren@wwwdotorg.org>:
ARM: tegra: DT-related fixes needed by the MMC tree
In order to convert the Tegra MMC driver to using mmc_of_parse(), some
bugs in the Tegra device-tree content need to be fixed first; it's
currently wrong but unused, and mmc_of_parse() causes that data to be
used for the first time.
* tag 'tegra-for-3.10-fixes-for-mmc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: dts: tegra: fix the activate polarity of cd-gpio in mmc host
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
have an Ethernet interface.
Little fixes mainly related to at91sam9x5 DT, IIO ADC bindings,
pinctrl for at91sam9260/g20 DT and the RTC addition.
Addition of the Acme Systems Aria G25 board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRXawWAAoJEAf03oE53VmQCgsH/R35if9zpMPsmWsRI8/DDIfb
t+7LIUwHsLaRLyfiQXaY5Rp1m9/a88+yKmiUseWm5QJWff9LuVpAc3zBYus75eGA
XEK9ugMmALionEukjzThOsnVeoxhsDzGjGBU43FSMovHwW6MWWChGegi9hfved+n
kZv8GgLjvIrDSsh7+jCN1qxtaf34s1PhT5+TIcPqvIGn4y4kqKRB6ZyTk781NA0n
+QJCaWyjPz21+b0r7+j70gMJ6FIfxfRzsmL24VB1KMq9Ly4+k6bGJIIMG2N9FIni
DGPoKPR2bpPVgZhRR/jSGx8qUS2+GJGuANGhpf2/yeuom1JLg9Ft0wZsDHDqClY=
=EC9a
-----END PGP SIGNATURE-----
Merge tag 'at91-dt' of git://github.com/at91linux/linux-at91 into next/dt
From Nicolas Ferre <nicolas.ferre@atmel.com>:
One macb DT node move for 9x5 family: 9g15 doesn't
have an Ethernet interface.
Little fixes mainly related to at91sam9x5 DT, IIO ADC bindings,
pinctrl for at91sam9260/g20 DT and the RTC addition.
Addition of the Acme Systems Aria G25 board.
* tag 'at91-dt' of git://github.com/at91linux/linux-at91:
ARM: at91/at91sam9260.dtsi: fix u(s)art pinctrl encoding
ARM: at91: dts: add adc resolution stuff
ARM: at91: add Acme Systems Aria G25 board
ARM: at91/dt: fix macb node declaration
ARM: at91: remove partial parameter in bootargs for at91sam9x5ek.dtsi
ARM: at91/trivial: fix model name for SAM9G15-EK
ARM: at91/trivial: typos in compatible property
ARM: at91/at91sam9x5: add RTC node
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Fix 'function-mask' referring to TRM (Omap 36xx) Section 13.4.4:
"Pad Functional Multiplexing and Configuration".
- Fix 'omap3_pmx_wkup' referring to TRM Table 13-6:
"Wkup Control Module Pad Configuration Register Fields".
Note that these fixes are not critical currently as we
are not yet using the missing range of pinmux registers
at this point.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add device-tree node for the 128MB NOR on the OMAP3430-SDP board.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add device-tree node for the 64MB NOR on the OMAP2420-H4 board.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The GPMC timing properties for device-tree have been updated by adding
a "-ns" or "-ps" suffix to indicate the units of time the property
represents (as suggested by Rob Herring). Therefore, update the timing
property names for the OMAP3430 SDP NAND and ONENAND devices.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add the "ti,gpio-always-on" property to the appropriate GPIO banks to
indicate which banks are always powered and will never lose logic state.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Update the DMTIMER compatibility property to reflect the register level
compatibilty between devices and update the various OMAP/AM timer
bindings with the appropriate compatibility string.
By doing this we can add platform specific data applicable to specific
timer versions to the driver. For example, errata flags can be populated
for the timer versions that are impacted.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
DT field of "interrupts" was mentioned wrongly as "interrupt" in SPI
node. This went unnoticed as spi-omap2 driver not making use of
interrupt. Fixes the typo.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add DT OPP table for OMAP4460 family of devices. This data is
decoded by OF with of_init_opp_table() helper function.
OPP data here is based on existing opp4xxx_data.c
This is in preparation to use generic cpufreq-cpu0 driver for device
tree enabled boot. Legacy non device tree enabled boot continues to
use omap-cpufreq.c and opp4xxx_data.c.
Signed-off-by: Nishanth Menon <nm@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Jon Hunter <jon-hunter@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
PandaBoard, PandaBoard-A4 revisions use OMAP4430.
PandaBoard-ES version of the board uses OMAP4460.
Move the original panda dts file into a common dtsi used by all panda
variants. This allows us to introduce SoC variation for PandaBoard ES
without impacting other PandaBoard versions that are supported.
As part of this change, since OMAP4460 adds on to OMAP4430, add
omap4.dtsi to omap4460.dtsi.
Signed-off-by: Nishanth Menon <nm@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Jon Hunter <jon-hunter@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add DT OPP table for OMAP443x family of devices. This data is
decoded by OF with of_init_opp_table() helper function.
OPP data here is based on existing opp4xxx_data.c
Since the omap4460 OPP tables would be different from OMAP443x,
introduce an new omap443x.dtsi for 443x specific entries and use
existing omap4.dtsi as the common dtsi file for all OMAP4 platforms.
This is in preparation to use generic cpufreq-cpu0 driver for device
tree enabled boot. Legacy non device tree enabled boot continues to
use omap-cpufreq.c and opp4xxx_data.c.
Signed-off-by: Nishanth Menon <nm@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Jon Hunter <jon-hunter@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Define VDD1 regulator in twl4030 DT and mark it as the supply for the
various OMAP34xx/35xx/36xx/37xx platforms (all use TWL4030 variants with
VDD1 supplying the CPU).
NOTE: This currently will use I2C1 bus communication path to set the
voltage in device tree boot. In the legacy non device tree boot, we
continue to use twl-common.c which bypasses I2C1 bus communication path
and uses I2C4 bus path using OMAP voltage libraries. We should
eventually be able to use I2C4 path once we have voltage regulator for
OMAP which is capable of using the voltage controller/voltage processor
IP blocks.
Signed-off-by: Nishanth Menon <nm@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Jon Hunter <jon-hunter@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add DT OPP table for OMAP36xx/37xx family of devices. This data is
decoded by OF with of_init_opp_table() helper function.
OPP data here is based on existing opp3xxx_data.c
This is in preparation to use generic cpufreq-cpu0 driver for device
tree enabled boot. Legacy non device tree enabled boot continues to
use omap-cpufreq.c and opp3xxx_data.c.
Signed-off-by: Nishanth Menon <nm@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Jon Hunter <jon-hunter@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add DT OPP table for OMAP34xx/35xx family of devices. This data is
decoded by OF with of_init_opp_table() helper function.
OPP data here is based on existing opp3xxx_data.c
Since the omap36xx OPP tables would be different from OMAP34xx/35xx,
introduce an new omap34xx.dtsi for 34xx/35xx specific entries and use
existing omap3.dtsi as the common dtsi file for all OMAP3 platforms.
This is in preparation to use generic cpufreq-cpu0 driver for device
tree enabled boot. Legacy non device tree enabled boot continues to
use omap-cpufreq.c and opp3xxx_data.c.
Signed-off-by: Nishanth Menon <nm@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Jon Hunter <jon-hunter@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add l3-noc node for OMAP4 and OMAP5 devices.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[jon-hunter@ti.com: Fix the problem caused by adding 32 to the interrupt
number for the L3 interrupts to account for per processor interrupts (PPI)
and software generated interrupts (SGI) which typically are mapped to the
first 32 interrupts in the ARM GIC. This is not necessary because the first
parameter of the ARM GIC interrupt property specifies the GIC interrupt
type (ie. SGI, PPI, etc). Hence, fix the interrupt number for the L3
interrupts by substracting 32]
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
To be able to run kernel in HYP mode, virtual timer
and GIC node information needs to be populated.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
GIC is not part of OCP space so move the gic DT node
out of ocp DT address space.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Specify both secure as well as nonsecure PPI IRQ for arch
timer. This fixes the following errors seen on DT OMAP5 boot..
[ 0.000000] arch_timer: No interrupt available, giving up
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
It has been decided to not duplicate banked modules dt nodes and that is
how the current arch timer dt extraction code is.
Update the OMAP5 DT file accordingly.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
On OMAP5 to detect invalid/bad memory accesses, 16MB of DDR is used as a trap.
Hence available memory for linux OS is 2032 MB on boards popullated with 2 GB
memory.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add the needed sections to enable audio support on
Devkit8000 when booted with DT blob.
Signed-off-by: Anil Kumar <anilk4.v@gmail.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
DevKit8000 is a beagle board clone from Timll, sold by
armkits.com. The DevKit8000 has RS232 serial port, LCD, DVI-D,
S-Video, Ethernet, SD/MMC, keyboard, camera, SPI, I2C, USB and
JTAG interface.
Add the basic DT support for devkit8000. It includes:
- twl4030 (PMIC)
- MMC1
- I2C1
- leds
Signed-off-by: Anil Kumar <anilk4.v@gmail.com>
Tested-by: Thomas Weber <thomas@tomweber.eu>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Adds basic device-tree support for OMAP3430 SDP board which has 256MB
of RAM, 128MB ONENAND flash, 256MB NAND flash and uses the TWL4030
power management IC.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The OMAP3 gpio bindings are currently missing the reg and interrupt
properties and so add these properties.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The OMAP gpio binding documention [1] states that the #interrupts-cells
property for gpio controllers should be 2. Currently, for OMAP3+ devices
the #interrupt-cells is set to 1. By setting this property to 2, it
allows clients to pass a 2nd parameter indicating the sensitivity (level
or edge) and polarity (high or low) of the interrupt. The OMAP gpio
controllers support these options and so update the #interrupt-cells
property for OMAP3+ devices to 2.
[1] Documentation/devicetree/bindings/gpio/gpio-omap.txt
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add the device-tree node for GPMC on OMAP2, OMAP4 and OMAP5 devices.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add SDMA controller binding for OMAP2+ devices and populate DMA client
information for SPI and MMC peripheral on OMAP3+ devices. Please note
that OMAP24xx devices do not have SPI and MMC bindings available yet and
so DMA client information is not populated.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add PMU nodes for OMAP2, OMAP3 and OMAP4460 devices.
Please note that the node for OMAP4460 has been placed in a separate
header file for OMAP4460, because the node is not compatible with
OMAP4430. The node for OMAP4430 is not included because PMU is not
currently supported on OMAP4430 due to the absence of a cross-trigger
interface driver.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add dwc3 omap glue data to the omap5 dt data file.
The information about the dt node added here is available @
Documentation/devicetree/bindings/usb/omap-usb.txt.
Also added dwc3 core dt data as a subnode to dwc3 omap glue
data in omap5 dt data file.
The information for the entered data node is available @
Documentation/devicetree/bindings/usb/dwc3.txt
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add omap-usb3 and omap-usb2 data node in OMAP5 device tree file.
The information for the node added here is available @
Documentation/devicetree/bindings/usb/usb-phy.txt
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add ocp2scp data node in omap5 device tree file.
The information for the node added here can be found @
Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add omap control usb data in OMAP5 device tree file.
This will have the register address of registers to
power on the USB2 PHY and USB3 PHY.
The information for the node added here is available in
Documentation/devicetree/bindings/usb/omap-usb.txt
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add usb otg data node in omap4/omap3 device tree file. Also update
the node with board specific setting in omapx-<board>.dts file.
The dt data specifies among others the interface type (ULPI or UTMI),
mode which is mostly OTG, power that specifies the amount of power
this can supply when in host mode.
The information about usb otg node is available @
Documentation/devicetree/bindings/usb/omap-usb.txt
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add omap-usb2 data node in omap4 device tree file. Since omap-usb2
is connected to ocp2scp, omap-usb2 dt data is added as a child node
of ocp2scp. The information about this data node is availabe @
Documentation/devicetree/bindings/usb/usb-phy.txt
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add omap control usb data in omap4 device tree file. This will have the
register address of registers to power on the PHY and to write to
mailbox. The information about this data node is available @
Documentation/devicetree/bindings/usb/omap-usb.txt
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Currently the OMAP General-Purpose Memory Controller (GPMC) device
node maps 16 MB of address space for its hardware registers.
This is because the OMAP Technical Reference Manual says that the
GPMC module register address space size is 16 MB. But in practice
the maximum address offset used by a GPMC register is 0x02d0.
So, there is no need to map such a big address space for GPMC regs.
This change was suggested by Jon Hunter [1].
[1]: https://patchwork.kernel.org/patch/2057111/
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add device-tree support for the GPMC controller on the OMAP3.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Booting 3.8-rc6 on omap4 panda results in the following error
[ 0.444427] omap_i2c 48070000.i2c: did not get pins for i2c error: -19
[ 0.445770] omap_i2c 48070000.i2c: bus 0 rev0.11 at 400 kHz
[ 0.473937] omap_i2c 48072000.i2c: did not get pins for i2c error: -19
[ 0.474670] omap_i2c 48072000.i2c: bus 1 rev0.11 at 400 kHz
[ 0.474822] omap_i2c 48060000.i2c: did not get pins for i2c error: -19
[ 0.476379] omap_i2c 48060000.i2c: bus 2 rev0.11 at 100 kHz
[ 0.477294] omap_i2c 48350000.i2c: did not get pins for i2c error: -19
[ 0.477996] omap_i2c 48350000.i2c: bus 3 rev0.11 at 400 kHz
[ 0.483398] Switching to clocksource 32k_counter
This happens because omap4 panda dts file is not adapted to use i2c through
pinctrl framework. Populating i2c pinctrl data to get rid of the error.
Tested on omap4460 panda with 3.8-rc6 kernel.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reported-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Booting 3.8-rc6 on omap 5430evm results in the following error
omap_i2c 48070000.i2c: did not get pins for i2c error: -19
[ 1.024261] omap_i2c 48070000.i2c: bus 0 rev0.12 at 100 kHz
[ 1.030181] omap_i2c 48072000.i2c: did not get pins for i2c error: -19
[ 1.037384] omap_i2c 48072000.i2c: bus 1 rev0.12 at 400 kHz
[ 1.043762] omap_i2c 48060000.i2c: did not get pins for i2c error: -19
[ 1.050964] omap_i2c 48060000.i2c: bus 2 rev0.12 at 100 kHz
[ 1.056823] omap_i2c 4807a000.i2c: did not get pins for i2c error: -19
[ 1.064025] omap_i2c 4807a000.i2c: bus 3 rev0.12 at 400 kHz
This happens because omap5 dts file is not adapted to use i2c through pinctrl
framework. Populating i2c pinctrl data to get rid of the error.
Tested on omap5430 evm with 3.8-rc6 kernel.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add the needed sections to enable audio support on Overo.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Booting 3.8-rc6 on omap 4430sdp results in the following error
omap_i2c 48070000.i2c: did not get pins for i2c error: -19
[ 1.024261] omap_i2c 48070000.i2c: bus 0 rev0.12 at 100 kHz
[ 1.030181] omap_i2c 48072000.i2c: did not get pins for i2c error: -19
[ 1.037384] omap_i2c 48072000.i2c: bus 1 rev0.12 at 400 kHz
[ 1.043762] omap_i2c 48060000.i2c: did not get pins for i2c error: -19
[ 1.050964] omap_i2c 48060000.i2c: bus 2 rev0.12 at 100 kHz
[ 1.056823] omap_i2c 4807a000.i2c: did not get pins for i2c error: -19
[ 1.064025] omap_i2c 4807a000.i2c: bus 3 rev0.12 at 400 kHz
This happens because omap4 dts file is not adapted to use i2c through pinctrl
framework. Populating i2c pinctrl data to get rid of the error.
Tested on omap4430 sdp with 3.8-rc6 kernel.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reported-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Convert the on-board LED connected to the TWL4030 (LEDB) to use
pwm-leds.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Section to describe the backlight for the LCD panels.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Sections to describe the pwm-leds in the system.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
We have proper driver stack to handle the pmu_stat LED which is connected
PWMB of twl4030.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Enable support for the PWMs and LED as PWM drivers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Enable support for the PWMs and LEDs as PWM drivers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add a new address space/memory resource to d_can device tree node. D_CAN
RAM initialization is achieved through RAMINIT register which is part of
AM33XX control module address space. D_CAN RAM init or de-init should be
done by writing instance corresponding value to control module register.
Till we have a separate control module driver to write to control module,
d_can driver will handle the register writes to control module by itself.
So a new address space to represent this control module register is added
to d_can driver.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add d_can instances to aliases node to get the D_CAN instance number
from the driver. To initialize D_CAN message RAM, corresponding instance
number is required.
To initialize instance 0 message RAM then 0x1 should be written and for
instance 1 message RAM, 0x2 should be written to control module register.
With device-tree framework ip instance number is "-1" by default for all
instances. To get device id/instance number then modules should be added
to DT "aliases" node. of_alias_get_id() gives the device id number based
on number of alias nodes present in "aliases node".
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
This is a follow-up to Javier Martinez effort adding initial
device tree support to IGEP technology devices [1].
It adds uart1 and uart2 bindings to the generic dtsi for the IGEP boards.
[1] http://www.spinics.net/lists/linux-omap/msg83409.html
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
ISEE IGEP COM Module is an TI OMAP3 SoC computer on module.
This patch adds an initial device tree support to boot an
IGEP COM Module from the MMC/SD.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
[b-cousson@ti.com: Update the Makefile for 3.8-rc2]
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
ISEE IGEPv2 is an TI OMAP3 SoC based embedded board.
This patch adds an initial device tree support to boot
an IGEPv2 from the MMC/SD.
Currently is working everything that is supported by DT
on OMAP3 SoCs (MMC/SD, GPIO LEDs, EEPROM, TWL4030 audio).
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
[benoit.cousson@linaro.org: Update the Makefile for 3.8-rc2]
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add a generic .dtsi device tree source file for the
common characteristics across IGEP Technology devices.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Rename I2C and GPIO nodes according to AM33XX TRM. According to
AM33XX TRM device instances are starting from "0" like i2c0, i2c1
and i2c3.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
[panto@antoniou-consulting.com: initial patch by pantelis's]
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
In the early days, the A10 and A13 shared quite some code. Nowadays it
shares less and less code, the A31 diverging even more, so it doesn't
make much sense to continue to maintain this structure, just use one
DTSI for every SoC, and that's it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
- Rename the clock compatible introduced in the first pull request for 3.10
- Complete the UART support for A13 and A10
- Adds clock gates support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJRXwBbAAoJEBx+YmzsjxAgDf8P/A3i6dGQe2DMnLRzJ8fwAsvj
VXqoC6YKEszelVSeQuqDE/pytoUfb1+1xEklkj95sHS4ds7fV6qVLM2Lp3TrBBEk
oGdwC6cS97BeNZxnnkTXUNWHlXdlFbkI7D0bd/GC4LLjrpUzu299BPdQ3zoXUEqf
xlm32aydivW87MX/1BfwdQPqA05x6/ZvOcxkWK6qQvXNl/iBoksJRjjQQdrCDxqz
fe34XbflblgQv3cmiONpi7BCFWzKVZcvDD1pHdgdNXiahpZjNMnFH7DEUhc24tTX
DHGwMwhvGDvjD/gp6h6xvCswYxMyLmFUZp2TKJ4ffd04/jncvPIUuSYzkeyUOGav
ZVBBik41Pxk+aKOX75vYffhHSb+AtmQqaORHLXidIOVC1UlnlHOj6RMODs2Z+JzG
kLhdy0fmLSaf6rKDvFAyqjR16apiaeRwxd581jKoFDn10P/c1Fg+R2FvrE8DA2fP
tiKDPrdO3U1CUq8PVYJFuN2D7SfkOSRz72tcMaFuBFnk7E0pmcgwzkvD7VqFexA4
Qf55VjSITMpVBX4L+TLCMgckp4OjcBQtwEgYQjwTNjtVRpr5BQUwBTHKCgRZt7jo
WaO8P4FLg4rka9aV52hNCka+O7qTeLOkfC08mZZGUkkfQ0gb4U8EAhdPRNsSiOHj
qtiLCwLX7X+WEIWs8vfo
=ErkU
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-3.10-2' of git://github.com/mripard/linux into next/dt
From Maxime Ripard <maxime.ripard@free-electrons.com>:
ARM: sunxi: dt additions for 3.10, take 2
- Rename the clock compatible introduced in the first pull request for 3.10
- Complete the UART support for A13 and A10
- Adds clock gates support
* tag 'sunxi-dt-for-3.10-2' of git://github.com/mripard/linux:
arm: sunxi: Add clock to pinctrl node
arm: sunxi: use the right clock phandles for UARTs
arm: sunxi: Add clock definitions for AXI, AHB, APB0, APB1 gates
ARM: sunxi: cubieboard: Add UART muxing
ARM: sunxi: hackberry: Add UART muxing
ARM: sunxi: dt: Add A10 UARTs to the dtsi.
ARM: sunxi: dt: Add uart3 dt node
ARM: sunxi: dt: Move uart0 to sun4i-a10.dtsi
ARM: sunxi: Rename uart nodes to serial
ARM: sunxi: dt: Use clocks property instead of clock-frequency for the UARTs
arm: sunxi: rename clock compatible strings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This branch adds two devices to the BCM2835 SoC device tree: the SPI
controller and the HW random number generator.
The SPI controller isn't actually instantiated in the Raspberry Pi
device tree, since there are no on-board SPI devices; it's up to the
end-user to modify their own device-tree to describe whatever they
have attached.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4Sjv
-----END PGP SIGNATURE-----
Merge tag 'bcm2835-for-3.10-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-rpi into next/dt
From Stephen Warren <swarren@wwwdotorg.org>:
ARM: bcm2835: device tree updates
This branch adds two devices to the BCM2835 SoC device tree: the SPI
controller and the HW random number generator.
The SPI controller isn't actually instantiated in the Raspberry Pi
device tree, since there are no on-board SPI devices; it's up to the
end-user to modify their own device-tree to describe whatever they
have attached.
* tag 'bcm2835-for-3.10-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-rpi:
ARM: bcm2835: add Broadcom BCM2835 RNG to the device tree
ARM: bcm2835: add SPI device to DT
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This series consists mainly of clean-ups for clockevents and
clocksource timers on OMAP2+ devices. The most significant change
in functionality comes from the 5th patch which is changing the
selection of the clocksource timer for OMAP3 and AM335x devices
when gptimers are used for clocksource.
Note that this series depends on 7185684 (ARM: OMAP: use
consistent error checking) in RMK's tree and 960cba6 (ARM:
OMAP5: timer: Update the clocksource name as per clock data)
in omap-for-v3.10/fixes-non-critical. So this branch is based
on a merge of 7185684 and omap-for-v3.10/fixes-non-critical
to avoid non-trivial merge conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=5kiA
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.10/timer-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/drivers
From Tony Lindgren <tony@atomide.com>:
Clean-up for omap2+ timers from Jon Hunter <jon-hunter@ti.com>:
This series consists mainly of clean-ups for clockevents and
clocksource timers on OMAP2+ devices. The most significant change
in functionality comes from the 5th patch which is changing the
selection of the clocksource timer for OMAP3 and AM335x devices
when gptimers are used for clocksource.
Note that this series depends on 7185684 (ARM: OMAP: use
consistent error checking) in RMK's tree and 960cba6 (ARM:
OMAP5: timer: Update the clocksource name as per clock data)
in omap-for-v3.10/fixes-non-critical. So this branch is based
on a merge of 7185684 and omap-for-v3.10/fixes-non-critical
to avoid non-trivial merge conflicts.
* tag 'omap-for-v3.10/timer-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4+: Fix sparse warning in system timers
ARM: OMAP2+: Store ID of system timers in timer structure
ARM: OMAP3: Update clocksource timer selection
ARM: OMAP2+: Simplify system timers definitions
ARM: OMAP2+: Simplify system timer clock definitions
ARM: OMAP2+: Remove hard-coded test on timer ID
ARM: OMAP2+: Display correct system timer name
ARM: OMAP2+: fix typo "CONFIG_BRIDGE_DVFS"
ARM: OMAP1: remove "config MACH_OMAP_HTCWIZARD"
ARM: OMAP: dpll: enable bypass clock only when attempting dpll bypass
ARM: OMAP2+: powerdomain: avoid testing whether an unsigned char is less than 0
ARM: OMAP2+: hwmod: Remove unused _HWMOD_WAKEUP_ENABLED flag
ARM: OMAP2+: am335x: Change the wdt1 func clk src to per_32k clk
ARM: OMAP2+: AM33xx: hwmod: Add missing sysc definition to wdt1 entry
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
These are needed for the USB PHY support, and are based on
commit 1f0972f5 from Felipe Balbi's tree as agreed on the
mailing lists.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=TU3y
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.10/usb-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/drivers
From Tony Lindgren <tony@atomide.com>:
EHCI platform data related changes for v3.10 merge window.
These are needed for the USB PHY support, and are based on
commit 1f0972f5 from Felipe Balbi's tree as agreed on the
mailing lists.
* tag 'omap-for-v3.10/usb-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (21 commits)
ARM: dts: omap3-beagle: Add USB Host support
ARM: dts: OMAP3: Add HS USB Host IP nodes
ARM: dts: OMAP4: Add HS USB Host IP nodes
ARM: OMAP: zoom: Adapt to ehci-omap changes
ARM: OMAP3: overo: Adapt to ehci-omap changes
ARM: OMAP3: omap3touchbook: Adapt to ehci-omap changes
ARM: OMAP3: omap3stalker: Adapt to ehci-omap changes
ARM: OMAP3: omap3pandora: Adapt to ehci-omap changes
ARM: OMAP3: omap3evm: Adapt to ehci-omap changes
ARM: OMAP3: igep0020: Adapt to ehci-omap changes
ARM: OMAP: devkit8000: Adapt to ehci-omap changes
ARM: OMAP3: cm-t3517: Adapt to ehci-omap changes
ARM: OMAP3: cm-t35: Adapt to ehci-omap changes
ARM: OMAP: AM3517evm: Adapt to ehci-omap changes
ARM: OMAP: AM3517crane: Adapt to ehci-omap changes
ARM: OMAP3: 3630SDP: Adapt to ehci-omap changes
ARM: OMAP3: 3430SDP: Adapt to ehci-omap changes
ARM: OMAP3: Beagle: Adapt to ehci-omap changes
ARM: OMAP2+: omap4panda: Adapt to ehci-omap changes
ARM: OMAP2+: omap-usb-host: Add usbhs_init_phys()
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds a arm-pmu node to bind device tree for exynos4210.
The exynos4210 and 4212 have two cpus which includes a pmu. In contrast, the
exynos4412 has 4 cpus and pmus. We need to define two more pmus for this type
board. However, supporting arm-pmu for the exynos4412 will handle it later
because there is no dts support for 4412 based board.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch enables arm-pmu to bind device tree for exynos5250. The exynos5250
has two pmus which have combiner irq type.
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
From Michal Simek <michal.simek@xilinx.com>:
This branch is based on zynq/clksrc/cleanup parts because
there are some dependencies on moving timer to generic location.
I could based it on standard Linux tagged version but you will get
several conflicts you will have to resolve.
If you are OK to resolving these problems, please let me know
I will create another branch with core-smp changes which are not based
on zynq/clksrc/cleanup branch.
* 'zynq/core-smp' of git://git.xilinx.com/linux-xlnx:
arm: zynq: Add hotplug support
arm: zynq: Add smp support
arm: zynq: Add smp_twd timer
arm: zynq: Get rid of xilinx function prefix
arm: zynq: Add support for system reset
arm: zynq: Move slcr initialization to separate file
arm: zynq: Load scu baseaddress at run time
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
PDMA0@0x121000 changes are added into the architecture DTS file.
Signed-off-by: Subash Patel <subash.rp@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add cpufreq controller device node for Exynos5440 SoC for passing
parameters like controller base address, interrupt and cpufreq
table. This node is added outside cpu0 as this driver is now a platform
driver and a new device structure is needed.
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The Exynos5440 common clock driver has changed the clock ID's for
some of the clocks. Fix the gmac clock entries in Exynos5440 dtsi
file accordingly.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Updated the bootargs to boot the system with rootfs in /dev/sda2
instead of ramdisk.
Signed-off-by: Subash Patel <subash.rp@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
PMU in exynos5440 generates one interrupt per core and needs to be
passed from DT to GIC to register it.
Signed-off-by: Subash Patel <subash.rp@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds node for GMAC for exynos5440 SoC supported by GMAC
driver.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Exynos5440 pin-controller generates eight interrupts to support
gpio interrupts. List those interrupt numbers in the pin-controller
node.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds FIMD related nodes for the Origen Quad board.
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds a common FIMD device node for all Exynos4 SoCs.
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds device tree node for the SYSREG registers block
found in Samsung S5P/Exynos SoC series. The SYSREG module
generates control signals for the ARM CPU and various IP blocks
and buses. SYSREG block registers are exposed through APB bus
interface. A sysreg device tree node is to be associated with
mfd syscon driver and all SYSREG clients should use regmap
interface it provides. It allows to eliminate any possible races
and conflicts should different drivers attempt to concurrently
access same register.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This adds common FIMD device node for all Exynos5 SoCs
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Exynos5440 has GIC which has virtualization support
in them. These are used by KVM.
Signed-off-by: Giridhar Maruthy <giridhar.m@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This is a fixup to two device tree nodes that have already landed but
without clock nodes since the transition to common clock happened at
the same time.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
[gautam.vivek@samsung.com: tested on smdk5250]
Tested-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The exynos 5250 SoC supports A15 style architected timers. Indicate
this through the device tree.
This is required by KVM.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The GIC in the exynos5250 SoC is A15 compliant. Show this through
the device tree, so that we can use the GIC for KVM.
Also add the respective A15 memory regions and interrupt links.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Added HDMI hot plug and regulator nodes to Arndale DT file.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
From Michal Simek <michal.simek@xilinx.com>:
It enables pmu support for zynq.
* 'zynq/core' of git://git.xilinx.com/linux-xlnx:
arm: zynq: Add support for pmu
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Michal Simek <michal.simek@xilinx.com>:
* 'zynq/clksrc/cleanup' of git://git.xilinx.com/linux-xlnx:
arm: zynq: Move timer to generic location
arm: zynq: Do not use xilinx specific function names
arm: zynq: Move timer to clocksource interface
arm: zynq: Use standard timer binding
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This series adds support for the pinctrl/gpio module on all arch-vt8500
supported SoCs.
As part of the review process, some tidy up is also done to
drivers/of/base.c to remove some code that is being constantly duplicated.
Also, a patch for the bcm2835 pinctrl driver is included to take advantage
of the new of/base.c code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRXQtJAAoJEAKiPfwuf9N/a/8H/3qun+1PnkDIGmC0amZDDrXD
tF8pruxccwOjh4Wug+UUzAwsBgej4NB193/ljFc35em9yFlZAcXBo0tLUd1gTxSd
nOkNWjYtFCK3hdmsE29Le9bRkCxn7g07uEkOKWSw79aYWrTRy63FDnr0p45YZvih
C4+ry92c50SJoW5kp+L6lS0aQjeBGXRCRcvuRBdwGPLYQXX/gEJfJrvU40ZrPByr
KJqhNOPoNS99OaVMPWDP4HCjCd/XVHBqd8Qz6M2uEIo2EBS0DnOt5IGoaRfTvEXM
Qx/y769v8/ndcdLAXFdPo+1ZgrrCXm7SozJhwAtMm3ruCxIN8u9LB6ZjMV2uaBo=
=+Y/Z
-----END PGP SIGNATURE-----
Merge tag 'vt8500/pinctrl' of git://server.prisktech.co.nz/git/linuxwmt into next/drivers
From Tony Prisk <linux@prisktech.co.nz>:
arm: vt8500: Add pinctrl driver for arch-vt8500
This series adds support for the pinctrl/gpio module on all arch-vt8500
supported SoCs.
As part of the review process, some tidy up is also done to
drivers/of/base.c to remove some code that is being constantly duplicated.
Also, a patch for the bcm2835 pinctrl driver is included to take advantage
of the new of/base.c code.
* tag 'vt8500/pinctrl' of git://server.prisktech.co.nz/git/linuxwmt: (606 commits)
pinctrl: bcm2835: make use of of_property_read_u32_index()
gpio: vt8500: Remove arch-vt8500 gpio driver
arm: vt8500: Remove gpio devicetree nodes
arm: dts: vt8500: Update Wondermedia SoC dtsi files for pinctrl driver
pinctrl: gpio: vt8500: Add pincontrol driver for arch-vt8500
arm: vt8500: Increase available GPIOs on arch-vt8500
of: Remove duplicated code for validating property and value
of: Add support for reading a u32 from a multi-value property.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Added S5M8767 PMIC DT nodes for Arndale board. Only the used
LDO's/BUCK are defined here. Also the nodes describe the default/reset
state LDO's and no power mangement tuning is implemented. The usage
desription can be found in s5m8767 device tree binding documentation.
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This is required to keep the existing functionality of having no
write protect pin on Arndale board.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add default pin state information for all client nodes that require
pin configuration support using pinctrl interface.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add default pin state information for all client nodes that require
pin configuration support using pinctrl interface.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
of these fixes are needed to support omap5 es2 version that includes
PM features while the earlier version es1 did not.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=mjWl
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.10/fixes-non-critical-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical
From Tony Lindgren <tony@atomide.com>:
Non critical omap fixes for v3.10 merge window. A big chunk
of these fixes are needed to support omap5 es2 version that includes
PM features while the earlier version es1 did not.
* tag 'omap-for-v3.10/fixes-non-critical-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: fix typo "CONFIG_BRIDGE_DVFS"
ARM: OMAP1: remove "config MACH_OMAP_HTCWIZARD"
ARM: OMAP: dpll: enable bypass clock only when attempting dpll bypass
ARM: OMAP2+: powerdomain: avoid testing whether an unsigned char is less than 0
ARM: OMAP2+: hwmod: Remove unused _HWMOD_WAKEUP_ENABLED flag
ARM: OMAP2+: am335x: Change the wdt1 func clk src to per_32k clk
ARM: OMAP2+: AM33xx: hwmod: Add missing sysc definition to wdt1 entry
Contains an update to 3.9-rc5
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- A couple mxs boards that run I2C at 400 kHz experience some unstable
issue occasionally. Slow down the clock speed to have I2C work
reliably.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRXCXBAAoJEFBXWFqHsHzOqg4H/irUyWQkIfch7us/vnMQnntr
y67TFoq1ucfHDA4/Okd5YxeUWjh0vaFJTVu5JLKfuT7HGTzSeqG4sFCp/A6/i9F9
ZGbcmTUSgG3erjpzN0R+PLxWO5iqjT8Mg3/cyK83SguKtf4u/MVJq8jpTyc0JJ9R
UNj4OaKN5n7tvPGAkj8ypWDpQwlczRRie6v+Nt1qWP1K7T7Ez9ZMkhOvd7WLUi4T
H7HcWo5IOUBzLvf7JmBAQwTCTdl7BJglBO5FjTn7ao0uaMEHLJOwzPWdXs08Agzh
qMVJcWqVCcQQmB5nuDDb08mlXXEYrt/92qL3LUejJaX76bPH+lzfCnvrDGUIuvo=
=Towm
-----END PGP SIGNATURE-----
Merge tag 'mxs-fixes-3.9-4' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo <shawn.guo@linaro.org>:
The mxs fixes for 3.9, take 4:
- A couple mxs boards that run I2C at 400 kHz experience some unstable
issue occasionally. Slow down the clock speed to have I2C work
reliably.
* tag 'mxs-fixes-3.9-4' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mxs: Slow down the I2C clock speed
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Instead of using a custom binding for retrieving the GPIO that activates the
LCD from devicetree, use a standard regulator.
This approach has the advantage to be more generic.
For example: in the case of a board that has a PMIC supplying the LCD voltage,
the current approach would not work, as it only searches for a GPIO pin.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The recent dtc+cpp support allows header files and C pre-processor
defines/macros to be used when compiling device tree files. These
headers will typically define various constants that are part of the
device tree bindings.
The original patch which set up the dtc+cpp include path only considered
using those headers from device tree files. However, most are also
useful for kernel code which needs to interpret the device tree.
In both the DT files and the kernel, I'd like to include the DT-related
headers in the same way, for example, <dt-bindings/gpio/tegra-gpio.h>.
That will simplify any text which discusses the DT header locations.
Creating a <dt-bindings/> for kernel source to use is as simple as
placing files into include/dt-bindings/.
However, when compiling DT files, the include path should be restricted
so that only the dt-bindings path is available; arbitrary kernel headers
shouldn't be exposed. For this reason, create a specific include
directory for use by dtc+cpp, and symlink dt-bindings from there to the
actual location of include/dt-bindings/. For want of a better location,
place this "include chroot" into the existing dts/ directory.
arch/*/boot/dts/include/dt-bindings -> ../../../../../include/dt-bindings
Some headers used by device tree files may not be useful to the kernel;
they may be used simply to aid in constructing the DT file (e.g. macros
to create a node), but not define any information that the kernel needs
to share. These may be placed directly into arch/*/boot/dts/ along with
the DT files themselves.
Acked-by: Michal Marek <mmarek@suse.cz>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
"ip" and "root" settings are useful for development
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Correct IDs for cdev1 and cdev2 are 94 and 93 respectively.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
[swarren: split into separate driver and device-tree patches]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Adding the PM configuration of PMC when the platform support suspend
function.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch adds "non-removable" property of MMC host where the eMMC device
is for Tegra platform.
And the "keep-power-in-suspend" property was used for the SDIO device that
need this to go into suspend mode (e.g. BRCM43xx series).
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This adds the power gpio key to DT and enable the wakeup of the gpio key
for the device. The Seaboard and paz00 already had the power gpio key
binding and the power key of Whistler was on KBC. So these boards' device
tree didn't include in this patch.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Set "regulator-always-on" for the SD slot on Dalmore, so that SD cards
work. This used to work, since this regulator is on by default, but was
broken by commit "ARM: tegra: dalmore: add TPS65090 node", since that
didn't specify always-on for this regulator.
In the long run, the regulators should all be hooked up to the SDHCI
device nodes. However, we haven't done that for any of the Tegra boards
yet, so to be consistent, this patch simply forces the regulator on,
rather than hooking it up and making it work differently to other boards.
Reported-by: Rhyland Klein <rklein@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Audio-related clocks need to be represented in the device tree. Update
bindings to describe which clocks are needed, and DT files to include
those clocks.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Audio-related clocks need to be represented in the device tree. Update
bindings to describe which clocks are needed, and DT files to include
those clocks.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
NVIDIA's Tegra114 reference platform Dalmore has voltage switch
regulators which are controlled by the Tegra GPIOs.
Add DT node for fixed regulators.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
NVIDIA's Tegra114 reference platform, Dalmore, uses the TPS65090 as
secondary PMICs which is mainly act as voltage switch regulator
controlled by i2c communication.
Add DT node for TPS65090.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: remove unit-address from node name since it's unique already]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Dalmore uses the TPS51632 as CPU regulator. The device is connected
on I2C5.
Add DT node for TPS51632.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch adds the node for the bq20z45 I2C gas gauge which is
compatible with the sbs-battery power supply driver.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
[swarren: remove unit-address from node name since it's unique already]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
NVIDIA's Tegra114 has 6 SPI controllers. These controllers are
redesign on T114 with different register interface.
Add DT entry for spi controllers and make it compatible with
"nvidia,tegra114-spi", since they are a new incompatible design.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: fixed reg property for 3rd SPI controller]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
NVIDIA's Tegra114 SoCs have the matrix keyboard controller which
supports 11x8 type of matrix. The number of rows and columns
are configurable.
Add DT entry for KBC controller with compatibility as "nvidia,tegra114-kbc".
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add APB DMA requestor and serial aliases for serial controller.
There are two serial drivers i.e. 8250 based simple serial driver
and APB DMA based serial driver for higher baudrate and performace.
The simple serial driver is selected by compatible value
"nvidia,tegra114-uart", "nvidia,tegra20-uart", and the APB DMA based
driver is selected by compatible value "nvidia,tegra114-hsuart",
"nvidia,tegra30-hsuart".
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
NVIDIA's Tegra114 has 5 I2C controllers. These controllers have the
following changes which makes incompatible with previous hardware:
- Single clock source to I2C controller.
- Interrupt support for per packet transfer.
Add DT entry for I2C controllers and make it compatible with
"nvidia,tegra114-i2c".
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: fixed location of status property for consistency]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
NVIDIA's Tegra114 has 32 channels APB DMA controller. Add DT entry for
APB DMA controllers and make it compatible with "nvidia,tegra114-apbdma".
Tegra114 DMA controller is not compatible with Tegra30/Tegra20 DMA
controller driver as in Tegra114, the global pause also clock gate the
DMA register and hence it iw not possible to write the DMA register
with global pause.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: fixed DT node order]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch adds a device tree node for the four PWM controllers present
on Tegra114.
Signed-off-by: Andrew Chew <achew@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
We should be defining the PWM nodes with status as "disabled" in the
chip-specific dtsi file, since we don't know whether specific boards
will use the PWM or not. This patch fixes the PWM node status for
Tegra20 and Tegra30.
Also fixed the one user of PWM, which is the Tegra20 medcom-wide board,
so that PWM is set to "okay" in the board-specific dts file.
Signed-off-by: Andrew Chew <achew@nvidia.com>
[swarren: in medcom-wide: fixed node sort order, removed duplicate pwm:
label, fixed syntax error]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Dalmore has a built-in eMMC device and a user-accessible SD card slot.
Add device tree nodes to enable these.
Based on changes by: Pritesh Raithatha <praithatha@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
[swarren: added commit description, fixed DT node sort order]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch adds in the SDHCI nodes for the busses supported on Tegra114
boards.
Signed-off-by: Pritesh Raithatha <praithatha@nvidia.com>
[Rhyland added clk refs to & reordered sdhci nodes and removed spaces]
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
[swarren: fixed DT node sort order]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The USB PHY nodes are all grouped together rather than being sorted based
on reg address like all other nodes fix this.
I apologize for the churn; I should have noticed this during review of the
patches that caused this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add references to tegra_car clocks for the basic device nodes. Also remove
the clock-frequency property of the serial node as the UART driver can now
use the clock framework to obtain the frequency.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The port controller needs the apb0_pio clock enabled to be able to
work. This commit declares that on the device tree.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
All the UARTs are connected to clock gates; now that our clock driver
is able to handle them, make the switch.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit adds the corresponding DT bindings for all the AXI,
AHB, APB0 and APB1 gates.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the ADC low and high resolution configuration and which one to use.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Macb0 node cannot be activated in generic sam9x5ek.dtsi file
as the sam9g15 does not have one.
Move the macb0 & macb1 activation in board .dts file that
support them.
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Move display timing configurations into device tree, so that the
auxdata for mxsfb driver can be killed.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Put the clock to the devicetree, so the driver can take care of it
later. Then, we don't have to do the enabling as a workaround in board
init.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
[shawn.guo: add enet_out into imx28.dtsi and overwrite it for m28evk]
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Now that a display timing binding is available, convert our almost identical
binding to use the standard binding.
This patch converts the vt8500 and wm8505 framebuffer drivers and
associated dts/dtsi files to use the standard binding as defined in
bindings/video/display-timing.txt.
There are two side-effects of making this conversion:
1) The fb node should now be in the board file, rather than the soc file as
the display-timing node is a child of the fb node.
2) We still require a bits per pixel property to initialize the framebuffer
for the different lcd panels. Rather than including this as part of the
display timing, it is moved into the framebuffer node.
I have also taken the opportunity to alphabetise the includes of each
driver to avoid double-ups.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The zynq has a Cortex-A9 with the corresponding smp_twd timers. Use them.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Zynq is standard PMU with 2 interrupt per core.
There is also access via register which is not used right now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use cdns,ttc because this driver is Cadence Rev06
Triple Timer Counter and everybody can use it
without xilinx specific function name or probing.
Also use standard dt description for timer
and also prepare for moving to clocksource
initialization.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove the gpio related devicetree nodes as these are no longer required
with the move to a combined pinctrl/gpio driver.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds pinctrl nodes to the VIA VT8500 and Wondermedia SoC dtsi
files to support the pinctrl driver.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Highlights:
* Add Lager board support
* Add ape6evm board support
* Add Bock-W board support
* Mackerel MMCIF/SDHI clean ups
* Add ethernet support to kzm9g-reference
This pull request is based on a merge of:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-pinmux2-for-v3.10
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-boards2-for-v3.10
The merge with renesas-pinmux2-for-v3.10 was made to provide
run-time dependencies for the following changes:
ARM: shmobile: APE6EVM LAN9220 support
ARM: shmobile: APE6EVM PFC support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Zhif
-----END PGP SIGNATURE-----
Merge tag 'renesas-boards3-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/boards2
Third round of Renesas ARM SoC board updates for v3.10
Highlights:
* Add Lager board support
* Add ape6evm board support
* Add Bock-W board support
* Mackerel MMCIF/SDHI clean ups
* Add ethernet support to kzm9g-reference
This pull request is based on a merge of:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-pinmux2-for-v3.10
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-boards2-for-v3.10
The merge with renesas-pinmux2-for-v3.10 was made to provide
run-time dependencies for the following changes:
ARM: shmobile: APE6EVM LAN9220 support
ARM: shmobile: APE6EVM PFC support
* tag 'renesas-boards3-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (307 commits)
ARM: shmobile: mackerel: clean up MMCIF vs. SDHI1 selection
ARM: shmobile: mackerel: add interrupt names for SDHI0
ARM: shmobile: mackerel: switch SDHI and MMCIF interfaces to slot-gpio
ARM: shmobile: mackerel: remove OCR masks, where regulators are used
ARM: shmobile: mackerel: SDHI resources do not have to be numbered
ARM: shmobile: Initial r8a7790 Lager board support
ARM: shmobile: APE6EVM LAN9220 support
ARM: shmobile: APE6EVM PFC support
ARM: shmobile: APE6EVM base support
ARM: shmobile: kzm9g-reference: add ethernet support
ARM: shmobile: add R-Car M1A Bock-W platform support
sh-pfc: r8a73a4: Remove unused GPIO bias data
ARM: shmobile: r8a73a4: Remove all GPIO enums
sh-pfc: r8a73a4: Remove function GPIOs
ARM: shmobile: r8a73a4: Remove IRQC function GPIOs
ARM: shmobile: r8a73a4: Remove SCIF function GPIOs
sh-pfc: r8a73a4: Remove IRQC function GPIOS
sh-pfc: r8a73a4: Remove SCIF function GPIOS
sh-pfc: r8a73a4: Add IRQC pin groups and functions
sh-pfc: r8a73a4: Add SCIF pin groups and functions
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds a device tree binding for random number generator present on
Broadcom BCM2835 SoC, used in Raspberry Pi and Roku 2 devices.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Highlights:
* Compilation fixes for sh7269 and for when CONFIG_BUG is not set
* sh-pfc Support for r8a73a4 SoC
* Move GPIOs handling from the PFC device to separate GPIO devices on the r8a7779 SoC
This pull request is based on a merge of:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-pinmux-for-v3.10
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-soc2-for-v3.10
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=vwDo
-----END PGP SIGNATURE-----
Merge tag 'renesas-pinmux2-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc2
Second round of Renesas ARM and SH based SoC pinmux updates for v3.10
Highlights:
* Compilation fixes for sh7269 and for when CONFIG_BUG is not set
* sh-pfc Support for r8a73a4 SoC
* Move GPIOs handling from the PFC device to separate GPIO devices on the r8a7779 SoC
This pull request is based on a merge of:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-pinmux-for-v3.10
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-soc2-for-v3.10
* tag 'renesas-pinmux2-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (185 commits)
sh-pfc: r8a73a4: Remove unused GPIO bias data
ARM: shmobile: r8a73a4: Remove all GPIO enums
sh-pfc: r8a73a4: Remove function GPIOs
ARM: shmobile: r8a73a4: Remove IRQC function GPIOs
ARM: shmobile: r8a73a4: Remove SCIF function GPIOs
sh-pfc: r8a73a4: Remove IRQC function GPIOS
sh-pfc: r8a73a4: Remove SCIF function GPIOS
sh-pfc: r8a73a4: Add IRQC pin groups and functions
sh-pfc: r8a73a4: Add SCIF pin groups and functions
sh-pfc: r8a73a4: Add bias (pull-up/down) pinconf support
sh-pfc: r8a73a4: GPIO IRQ support
sh-pfc: r8a73a4: Support sparse GPIO numbers
sh-pfc: Add r8a73a4 pinmux support
sh-pfc: r8a7779: Split DU input and output pixel clocks
sh-pfc: r8a7779: Remove GPIO data
ARM: shmobile: r8a7779: Register GPIO devices
sh-pfc: Configure pins as GPIOs at request time when handled externally
sh-pfc: Skip gpiochip registration when no GPIO resource is found
sh-pfc: Make GPIO support optional
sh-pfc: Make function GPIOs support optional
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Some Highlights:
* Add r8a7790 SoC
* Add r8a73a4 SoC
* Migrate r8a7740 SoC from INTC to GIC
* Add thermal driver support to r8a73a4 SoC
* Add irqpin DT nodes to sh73a0 SoC
* Add SCIF support to r8a7778 SoC
This pull request is based on a merge of:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-soc-for-v3.10
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-intc-external-irq2-for-v3.10
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=jivx
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc2-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc2
Second round of Renesas ARM SoC updates for v3.10
Some Highlights:
* Add r8a7790 SoC
* Add r8a73a4 SoC
* Migrate r8a7740 SoC from INTC to GIC
* Add thermal driver support to r8a73a4 SoC
* Add irqpin DT nodes to sh73a0 SoC
* Add SCIF support to r8a7778 SoC
This pull request is based on a merge of:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-soc-for-v3.10
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-intc-external-irq2-for-v3.10
* tag 'renesas-soc2-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (88 commits)
ARM: shmobile: r8a7790 SoC 64-bit DT support
ARM: shmobile: r8a73a4 SoC 64-bit DT support
ARM: shmobile: r8a7790 PFC support
ARM: shmobile: r8a7790 IRQC support
ARM: shmobile: r8a7790 SCIF support
ARM: shmobile: Initial r8a7790 SoC support
ARM: shmobile: r8a7779: move global functions to r8a7779.h
ARM: shmobile: r8a7740: move global functions to r8a7740.h
ARM: shmobile: sh73a0: move global functions to sh73a0.h
ARM: shmobile: sh7372: move global functions to sh7372.h
ARM: shmobile: r8a7779: remove DIV4 clocks and use fixed ratio clock
ARM: shmobile: r8a7740: use fixed ratio clock
ARM: shmobile: r8a7740: tidyup comment/implementation mismatch
ARM: shmobile: sh73a0: use fixed ratio clock
ARM: shmobile: sh7372: use fixed ratio clock
ARM: shmobile: add struct clk_ratio and fixed ratio clock macro
ARM: shmobile: sh7372: remove DIV4_ZT* clocks
ARM: shmobile: sh73a0: remove DIV4_ZT* clocks
ARM: shmobile: sh73a0: add a TWD clock
ARM: shmobile: r8a7740: Migrate from INTC to GIC
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Add tps6507x regulator device tree data to da850-evm by
adding regulator consumers with tightened constraints
and regulator-name.TPS6507x regulator handle can be obtained
by using this regulator name.
Regulator constraints are added as per da850 board file.
Regulator names are given as per maximum output voltage the
regulator is capable to provide.
for e.g. regulator name for dcdc1 is "VDCDC1_3.3V".
Also, add tps6507x PMIC I2C slave device under I2C0 node.
Tested on da850-evm.
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add device tree data for tps6507x regulator by adding
all tps6507x regulator nodes. Regulators are initialized
based on compatible name provided in tps6507x DT file.
All tps6507x PMIC regulator device tree nodes are placed
in a separate device tree include file (tps6507x.dtsi).
tps6507x.dtsi file is created using datasheet
http://www.ti.com/lit/ds/symlink/tps65070.pdf
Tested on da850-evm.
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This patch adds support for the thermal controller available in
all Armada 370 boards. This controller has two 4-byte registers:
one to read the thermal sensor, the other for sensor initialization.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds support for the thermal controller available in
all Armada XP boards. This controller has two 4-byte registers:
one to read the thermal sensor, the other for sensor initialization.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>