If the Renesas R-Car GPIO driver cannot find a functional clock, it
prints a warning, .e.g.
gpio_rcar ffc40000.gpio: unable to get clock
and continues, as the clock is optional, depending on the SoC type.
This warning may confuse users.
To fix this, add a flag to indicate that the clock is mandatory or
optional:
- If the clock is mandatory (on R-Car Gen2 and Gen3), a missing clock
is now treated as a fatal error,
- If the clock is optional (on R-Car Gen1), the warning is no longer
printed.
Suggested-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit 4baadb9e05 ("ARM: shmobile: r8a7778: remove obsolete
setup code"), Renesas R-Car SoCs are only supported in generic DT-only
ARM multi-platform builds. The driver doesn't need to use platform data
anymore, hence remove platform data configuration.
Make gpio_rcar_priv.has_both_edge_trigger a boolean for consistency with
gpio_rcar_info.has_both_edge_trigger.
Move gpio_rcar_priv.irq_parent down while we're at it, to prevent gaps
on 64-bit.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some drivers require a way to translate GPIO pins to their IRQ numbers.
This patch adds the .to_irq() gpiolib callback to the pinctrl-xway
driver, which returns an IRQ mapping for a given GPIO pin.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Martin Schiller <mschiller@tdt.de>
[Switched ->dev to ->parent]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These new helpers simplify implementing multi-driver modules and
properly handle failure to register one driver by unregistering all
previously registered drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES 104-IDIO-16 uses a single interrupt to indicate a possible
change-of-state in any of the digital input lines. As such, only a
single write to the device's "Clear Interrupt" register is necessary to
acknowledge the IRQ for all respective GPIO.
This patch moves the "Clear Interrupt" register write operation from the
irq_ack callback to the IRQ handler function, wherefore each interrupt
may be cleared respectively by executing a single outb call at the end
of the idio_16_irq_handler function, rather than multiple redundant outb
calls as a result of the generic_handle_irq call for each masked GPIO.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The .dev field has been renamed .parent in the GPIO tree.
Fix it up.
Cc: Yendapally Reddy Dhananjaya Reddy <yrdreddy@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the initial support of the Broadcom NSP gpio-a driver.
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yrdreddy@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PCI/USB expander menus already depend on PCI/USB, drop subdependecies
on individual drivers.
Signed-off-by: Andrew F. Davis <afd@ti.com>
[Rebased to the GPIO tree]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allow GPIOs from the gpio-pch driver to be referenced from device tree
by simply setting the struct gpio_chip of_node pointer to that of the
struct pci_dev.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allow the pch_gpio driver to be built for MIPS platforms, in preparation
for use on the MIPS Boston board.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently the 74x164 driver assembles an SPI message from an array of
one-byte SPI transfers, one for each daisy-chained shift register, as
the first byte sent will end up in the last register.
This array is allocated and deallocated on each GPIO write access.
By storing the data in the internal buffer in reverse order, we can
use a single SPI transfer with the internal buffer directly, simplifying
the code a lot, and avoiding memory (de)allocations.
This also avoids transient values on the GPIO outputs when using an SPI
master that cannot keep the hardware chip select asserted in between
multiple transfers (and would need cs-gpios for proper operation).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Mark Brown <broonie@kernel.org>
[Rebased changing .dev to .parent]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
By moving the internal buffer to the end of struct gen_74x164_chip and
converting it from a pointer to a zero-sized array, it can be allocated
together with gen_74x164_chip, reducing the number of managed
allocations.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The interrupt management is changed by this patch to rely on chip data
instead of chained interrupts.
The main goal is to loosen the dependency on the global pxa chip
structure in favor of the passed chip data. The secondary goal is to
better show in /proc/interrupts the difference between interrupts for
gpio0 and gpio1 (directly wired to interrupt controller), and the other
gpios (wired onto a third line in the interrupt controller).
The last advantage of this patch is that the interrupt is actually
requested, so that another driver cannot steal this line, or overwrite
the handler.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the device managed ioremap to simplify the probe function.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pxa gpio IP is provided by one chip, which holds multiple banks.
Another reason the driver should register only one gpiochip instead of
multiple gpiochips (ie. 1 per each bank) is that for pincontrol and
devicetree integration (think gpio-ranges), it's impossible to have the
contiguous pin range 0..127 mapped to gpios 0..127.
This patch, amongst other thinks, paves the path to loosen the bond with
the global structure variable pxa_gpio_chip.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After adding the DT matching in
commit 6f29c9afbe
"gpio: pca935x: fix of-only probed devices"
compilation fails like this:
CC [M] drivers/gpio/gpio-pca953x.o
gpio-pca953x.c: In function ‘pca953x_probe’:
gpio-pca953x.c:693:11: error: implicit declaration of
function ‘of_match_device’ [-Werror=implicit-function-declaration]
match = of_match_device(pca953x_dt_ids, &client->dev);
^
gpio-pca953x.c:693:9: warning: assignment makes pointer from
integer without a cast [-Wint-conversion]
match = of_match_device(pca953x_dt_ids, &client->dev);
^
cc1: some warnings being treated as errors
../scripts/Makefile.build:264: recipe for target
'drivers/gpio/gpio-pca953x.o' failed
After removing the conditional inclusion guards compilation
works fine again. Might be a module problem so that
fix.
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the pca953x device is probed from OF using the proper OF probing then
the i2c-client will be NULL and the device probe will fail as id is NULL
and it isn't an ACPI device (previous drivers would simply OOPS out).
Add support for the of_device_id table having the same data as the others
so that the correct paths will be taken when registering a device.
An example of current valid of node which did not work:
gpio@38 {
compatible = "onsemi,pca9654", "nxp,pca9534";
reg = <0x38>;
interrupt-parent = <&gpio5>;
interrupts = <25 IRQ_TYPE_LEVEL_LOW>;
};
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add onsemi,pca9654 which is also compatible with the nxp,pca9524 as it
is an 8bit expander with an interrupt output.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIOs are part of the AC'97 spec, enable their use on embedded platforms
using AC'97.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWX4h6AAoJECTWi3JdVIfQhIoH/2BB+Cdyzob3aAcIarYAPdsZ
bMXjDYyTyK1HanEUXGueQ7+CruQqXynRHhN3VRhmbjhJ+DgDP2GdgG53bm6q0J5z
TjoflP51OMX2boVokdyR3omOvuvoBDvhutVrHk5b/3Uye0p2yQ9kqdZgbvc8QE21
8QvJrm1PUg4OTj+xdUdl/uKweV7VUVMBob11NIM2C8UvURSv0lV+4UG/jy/fMHlz
KA/U0mPqCAz93XahxDHJzJsAO2O3q7K5Z1y5ZT0YXfrLiOFRGSIQSVjSZjPxAJkm
TAO6UMrxvLPEWuSqf5NcaMve5gveVbmHfocE/JvnRO8ylgGswF7wSflMPbcuYQ8=
=Fg8T
-----END PGP SIGNATURE-----
Merge tag 'asoc-ac97-gpio' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into devel
ASoC: Add a GPIO chip for AC'97
GPIOs are part of the AC'97 spec, enable their use on embedded platforms
using AC'97.
I missed to convert this driver properly to use .parent to
point to the parent device. ARMv7 multiplatform would not
compile.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES 104-IDI-48 family of PC/104 utility boards feature 48
individually optically isolated digital inputs. Enabled inputs feature
change-of-state detection capability; if change-of-state detection is
enabled, an interrupt is fired off if a change of input level
(low-to-high or high-to-low) is detected. Change-of-state IRQs are
enabled/disabled on 8-bit boundaries, for a total of six boundaries.
This driver provides GPIO and IRQ support for these 48 channels of
digital input. The base port address for the device may be configured
via the idi_48_base module parameter. The interrupt line number for the
device may be configured via the idi_48_irq module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Nizam Haider <nijamh@cdac.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
IRQ should be disabled on device probe so that the device IRQ is in a
known starting state. If IRQ is not disabled, interrupts may be reported
as handled by the IRQ handler, despite no irq_unmask calls made by the
user.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit f4d566a8a0e6 ("gpio: change member .dev to .parent") changes
member of gpiochip from .dev to .parent. Update the corresponding
comment.
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To prevent confusion, and to match the existing coding style used in
other GPIO drivers, symbol names within the 104-idio-16 GPIO driver
should be lowercase.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to check if number of gpio is positive if there is no
such check in devicetree or acpi or whatever called before
gpiochip_add.
I suppose that devicetree and acpi do not allow insert gpiochip
with zero number but I do not know if it is enough to ignore
this check in gpiochip_add.
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are limitations for the current checker:
1. Could not check the overlap if the new gpiochip is the secondly
gpiochip.
2. Could not check the overlap if the new gpiochip is overlap
with the left of gpiochip. E.g. if we insert [c, d] between
[a,b] and [e, f], and e >= c + d, it will successful even if
c < a + b.
3. Allow overlap of base of different gpiochip.
This patch fix these issues by checking the overlap of both right and
left gpiochip in the same loop statement.
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
[Tweaked to remove unnecessary ret variable]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The commit f881bab038 ("gpio: keep the GPIO line names internal")
change the error to warning in gpiochip_set_desc_names. Update the
comment accordingly.
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch is a second attempt at what was previously in commit
6c7e660a27 ("gpio: pxa: set initcall level to module init").
The goal is the same : enable gpio & pinctrl driver to work
together. As pinctrl driver will be initialized at device level, the
gpio should be as well, so that the deferring mechanism is honored.
Yet this patch should also respect the legacy platforms, so the set of
constraints is :
- in legacy platforms (ie. non dt), gpio_[gs]et_*() should be available
for machine code => core initcall
- in new platforms (ie. dt based), pinctrl will be available and no
machine code => device initcall
In order to fullfill all these constraints, the initcall level is either
postcore for non devicetree platforms, and device for devicetree platforms.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
I'm not as involved in OMAP as I used to be and Grygorii is the most
active developer working on this driver and has also been reviewing
patches so let's add him as a driver maintainer instead of me.
While being there, add the driver's DT binding doc to the file list.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We should not fall back to the legacy unnamed gpio lookup style if the
driver requests gpios with different names, because we'll give out the same
gpio twice. Let's keep track of the names that were used for the device and
only do the fallback for the first name used.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The TPS65086 PMIC contains several regulators and a GPO controller.
Add bindings for the TPS65086 GPO controller.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES 104-IDIO-16 series offers Change-of-State detection interrupt
functionality; if Change-of-State detection is enabled, an interrupt is
fired off if any input line changes state (i.e. goes from low to high,
or from high to low). This patch adds support to handle these interrupts
and allows the user to mask which GPIO lines are affected. The interrupt
line number for the device may be set via the idio_16_irq module
parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The name .dev in a struct is normally reserved for a struct device
that is let us say a superclass to the thing described by the struct.
struct gpio_chip stands out by confusingly using a struct device *dev
to point to the parent device (such as a platform_device) that
represents the hardware. As we want to give gpio_chip:s real devices,
this is not working. We need to rename this member to parent.
This was done by two coccinelle scripts, I guess it is possible to
combine them into one, but I don't know such stuff. They look like
this:
@@
struct gpio_chip *var;
@@
-var->dev
+var->parent
and:
@@
struct gpio_chip var;
@@
-var.dev
+var.parent
and:
@@
struct bgpio_chip *var;
@@
-var->gc.dev
+var->gc.parent
Plus a few instances of bgpio that I couldn't figure out how
to teach Coccinelle to rewrite.
This patch hits all over the place, but I *strongly* prefer this
solution to any piecemal approaches that just exercise patch
mechanics all over the place. It mainly hits drivers/gpio and
drivers/pinctrl which is my own backyard anyway.
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AC97 specification provides a guide for 16 GPIOs in the codecs. If
the gpiolib is compiled in the kernel, declare a gpio chip.
This was tested with a pxa27x board (mioa701) and a wm9713 codec.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull perf updates from Thomas Gleixner:
"Mostly updates to the perf tool plus two fixes to the kernel core code:
- Handle tracepoint filters correctly for inherited events (Peter
Zijlstra)
- Prevent a deadlock in perf_lock_task_context (Paul McKenney)
- Add missing newlines to some pr_err() calls (Arnaldo Carvalho de
Melo)
- Print full source file paths when using 'perf annotate --print-line
--full-paths' (Michael Petlan)
- Fix 'perf probe -d' when just one out of uprobes and kprobes is
enabled (Wang Nan)
- Add compiler.h to list.h to fix 'make perf-tar-src-pkg' generated
tarballs, i.e. out of tree building (Arnaldo Carvalho de Melo)
- Add the llvm-src-base.c and llvm-src-kbuild.c files, generated by
the 'perf test' LLVM entries, when running it in-tree, to
.gitignore (Yunlong Song)
- libbpf error reporting improvements, using a strerror interface to
more precisely tell the user about problems with the provided
scriptlet, be it in C or as a ready made object file (Wang Nan)
- Do not be case sensitive when searching for matching 'perf test'
entries (Arnaldo Carvalho de Melo)
- Inform the user about objdump failures in 'perf annotate' (Andi
Kleen)
- Improve the LLVM 'perf test' entry, introduce a new ones for BPF
and kbuild tests to check the environment used by clang to compile
.c scriptlets (Wang Nan)"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (32 commits)
perf/x86/intel/rapl: Remove the unused RAPL_EVENT_DESC() macro
tools include: Add compiler.h to list.h
perf probe: Verify parameters in two functions
perf session: Add missing newlines to some pr_err() calls
perf annotate: Support full source file paths for srcline fix
perf test: Add llvm-src-base.c and llvm-src-kbuild.c to .gitignore
perf: Fix inherited events vs. tracepoint filters
perf: Disable IRQs across RCU RS CS that acquires scheduler lock
perf test: Do not be case sensitive when searching for matching tests
perf test: Add 'perf test BPF'
perf test: Enhance the LLVM tests: add kbuild test
perf test: Enhance the LLVM test: update basic BPF test program
perf bpf: Improve BPF related error messages
perf tools: Make fetch_kernel_version() publicly available
bpf tools: Add new API bpf_object__get_kversion()
bpf tools: Improve libbpf error reporting
perf probe: Cleanup find_perf_probe_point_from_map to reduce redundancy
perf annotate: Inform the user about objdump failures in --stdio
perf stat: Make stat options global
perf sched latency: Fix thread pid reuse issue
...
Pull scheduler fix from Thomas Gleixner:
"A single fix to prevent math underflow in the numa balancing code"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/numa: Fix math underflow in task_tick_numa()
Pull liblockdep fixes from Thomas Gleixner:
"Three small patches to synchronize liblockdep with the latest core
changes"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tools/liblockdep: explicitly declare lockdep API we call from liblockdep
tools/liblockdep: add userspace versions of WRITE_ONCE and RCU_INIT_POINTER
tools/liblockdep: remove task argument from debug_check_no_locks_held
Pull x86 fixes from Thomas Gleixner:
"A couple of fixes and updates related to x86:
- Fix the W+X check regression on XEN
- The real fix for the low identity map trainwreck
- Probe legacy PIC early instead of unconditionally allocating legacy
irqs
- Add cpu verification to long mode entry
- Adjust the cache topology to AMD Fam17H systems
- Let Merrifield use the TSC across S3"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Call verify_cpu() after having entered long mode too
x86/setup: Fix low identity map for >= 2GB kernel range
x86/mm: Skip the hypervisor range when walking PGD
x86/AMD: Fix last level cache topology for AMD Fam17h systems
x86/irq: Probe for PIC presence before allocating descs for legacy IRQs
x86/cpu/intel: Enable X86_FEATURE_NONSTOP_TSC_S3 for Merrifield
Pull irq and timer fixes from Thomas Gleixner:
- An irq regression fix to restore the wakeup behaviour of chained
interrupts.
- A timer fix for a long standing race versus timers scheduled on a
target cpu which got exposed by recent changes in the workqueue
implementation.
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/PM: Restore system wake up from chained interrupts
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timers: Use proper base migration in add_timer_on()
Pull MIPS updates from Ralf Baechle:
"These are the highlists of the main MIPS pull request for 4.4:
- Add latencytop support
- Support appended DTBs
- VDSO support and initially use it for gettimeofday.
- Drop the .MIPS.abiflags and ELF NOTE sections from vmlinux
- Support for the 5KE, an internal test core.
- Switch all MIPS platfroms to libata drivers.
- Improved support, cleanups for ralink and Lantiq platforms.
- Support for the new xilfpga platform.
- A number of DTB improvments for BMIPS.
- Improved support for CM and CPS.
- Minor JZ4740 and BCM47xx enhancements"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (120 commits)
MIPS: idle: add case for CPU_5KE
MIPS: Octeon: Support APPENDED_DTB
MIPS: vmlinux: create a section for appended DTB
MIPS: Clean up compat_siginfo_t
MIPS: Fix PAGE_MASK definition
MIPS: BMIPS: Enable GZIP ramdisk and timed printks
MIPS: Add xilfpga defconfig
MIPS: xilfpga: Add mipsfpga platform code
MIPS: xilfpga: Add xilfpga device tree files.
dt-bindings: MIPS: Document xilfpga bindings and boot style
MIPS: Make MIPS_CMDLINE_DTB default
MIPS: Make the kernel arguments from dtb available
MIPS: Use USE_OF as the guard for appended dtb
MIPS: BCM63XX: Use pr_* instead of printk
MIPS: Loongson: Cleanup CONFIG_LOONGSON_SUSPEND.
MIPS: lantiq: Disable xbar fpi burst mode
MIPS: lantiq: Force the crossbar to big endian
MIPS: lantiq: Initialize the USB core on boot
MIPS: lantiq: Return correct value for fpi clock on ar9
MIPS: ralink: Add missing clock on rt305x
...
Here are a collection of small fixes tha have been gathered for
4.4-rc1. The only significant changes are those in PCI drivers
Kconfig, to use "depends on" instead of "select" for CONFIG_ZONE_DMA.
A reverse select is often more user-friendly, but in this case, it
makes hard to manage with the conflict with ZONE_DEVICE, so changed in
such a way for now.
Others are all small fixes and quirks: an error check in soundcore
reigster_chrdev(), HD-audio HDMI/DP phantom jack fix, Intel Broxton DP
quirk, USB-audio DSD device quirk, some constifications, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=k0zD
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a collection of small fixes tha have been gathered for
4.4-rc1. The only significant changes are those in PCI drivers
Kconfig, to use "depends on" instead of "select" for CONFIG_ZONE_DMA.
A reverse select is often more user-friendly, but in this case, it
makes hard to manage with the conflict with ZONE_DEVICE, so changed in
such a way for now.
Others are all small fixes and quirks: an error check in soundcore
reigster_chrdev(), HD-audio HDMI/DP phantom jack fix, Intel Broxton DP
quirk, USB-audio DSD device quirk, some constifications, etc"
* tag 'sound-fix-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: pci: depend on ZONE_DMA
ALSA: hda - Simplify phantom jack handling for HDMI/DP
ALSA: hda/hdmi - apply Skylake fix-ups to Broxton display codec
ALSA: ctxfi: constify rsc ops structures
ALSA: usb: Add native DSD support for Aune X1S
ALSA: oxfw: add an comment to Kconfig for TASCAM FireOne
sound: fix check for error condition of register_chrdev()
- A bunch of brown paper bag bugs (MAINTAINERS list email, SMP build failure)
- cpu_relax() now compiler barrier for UP as well
- Handling of userspace Bus Errors for ARCompact builds
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=isVd
-----END PGP SIGNATURE-----
Merge tag 'arc-4.4-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"Found a couple of brown paper bag bugs with the prev pull request
(including a SMP build breakage report from Guenter). Since these are
urgent I also decided to send over a bunch of other pending fixes
which could have otherwise waited an rc or two.
Summary:
- A bunch of brown paper bag bugs (MAINTAINERS list email, SMP build
failure)
- cpu_relax() now compiler barrier for UP as well
- handling of userspace Bus Errors for ARCompact builds"
* tag 'arc-4.4-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: Fix silly typo in MAINTAINERS file
ARC: cpu_relax() to be compiler barrier even for UP
ARC: use ASL assembler mnemonic
ARC: [arcompact] Handle bus error from userspace as Interrupt not exception
ARC: remove extraneous header include
ARCv2: lib: memcpy: use local symbols
