The XRX200 family of SoCs has embedded gigabit PHYs. This patch adds code to
boot them up.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4522
Use common clock infrastructure instead of private APIs.
1. Enable COMMON_CLK in the Kconfig.
2. Remove private clock APIs, which are replaced by the code in
drivers/clk/clk-ls1x.c.
3. Modify header file for drivers/clk/clk-ls1x.c.
Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/4431
Signed-off-by: John Crispin <blogic@openwrt.org>
On XLR/XLS, the cpu cores communicate with fast on-chip devices
(e.g. network accelerator, security engine etc.) using the Fast
Messaging Network(FMN). The FMN queues and credits needs to be
configured and intialized before it can be used.
The co-processor 2 on XLR/XLS CPU cores has registers for FMN access,
and the XLR/XLS has custom instructions for sending and loading
messages. The FMN can deliver also per-cpu interrupts when messages
are available at the CPU.
This patch adds FMN initialization, adds interrupt setup and handling,
and also provides support for sending and receiving FMN messages.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4468
Signed-off-by: John Crispin <blogic@openwrt.org>
Create struct nlm_pic_irq for interrupts handled by the PIC.
This simplifies IRQ handling for multi-SoC as well as
the single SoC cases. Also split the setup of percpu and PIC
interrupts so that we can configure the PIC interrupts for
every node.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4467
Signed-off-by: John Crispin <blogic@openwrt.org>
There can be 1, 2 or 4 SoCs(nodes) in a multi-chip XLP board. Add an
option for multi-chip boards in case of XLP, and make the number of
nodes configurable.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4470
Signed-off-by: John Crispin <blogic@openwrt.org>
Upto 4 Netlogic XLP SoCs can be connected over ICI links to form a
coherent multi-node system. Each SoC has its own set of on-chip
devices including PIC. To support this, add a per SoC stucture and
use it for the PIC and SYS block addresses instead of using global
variables.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4469
Signed-off-by: John Crispin <blogic@openwrt.org>
Initial code to support more than 32 cpus. The platform CPU mask
is updated from 32-bit mask to cpumask_t. Convert places that use
cpu_/cpus_ functions to use cpumask_* functions.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4464
Signed-off-by: John Crispin <blogic@openwrt.org>
Remove unused and trivial PIC accesss functions, update nlm_pic_send_ipi()
and nlm_set_irt_to_cpu() to use similar logic, and use correct type for
reg in nlm_pic_disable_irt().
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4463
Signed-off-by: John Crispin <blogic@openwrt.org>
Used the hardware thread id passed in while writing to IRT in
nlm_pic_init_irt()
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4465
Signed-off-by: John Crispin <blogic@openwrt.org>
Refactor nvram related functions into its own unit for easier expansion
and exposure of the values to other drivers.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/4516
Signed-off-by: John Crispin <blogic@openwrt.org>
Add a reset helper for resetting the different cores.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/4455
Signed-off-by: John Crispin <blogic@openwrt.org>
The softreset register description for BCM6358 was missing, so add it.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/4454
Signed-off-by: John Crispin <blogic@openwrt.org>
There are bcma based devices like the Linksys E2000 out there, which do
have one ieee80211 core, but no PCIe core and they are using no
prefixes for the sprom. In addition some values like boardtype are
stored without a prefix for the main SoC chip also when they have an
additional PCIe wifi chip with an own boardtype var on some devices.
The Ethernet addresses are now also read out correctly without a prefix
so calling bcm47xx_fill_sprom_ethernet is not needed any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4364
Signed-off-by: John Crispin <blogic@openwrt.org>
For non MIPSr2 processors, such as the BMIPS 5000, calls to
arch_local_irq_disable() and others may be preempted, and in doing
so a stale value may be restored to c0_status. This fix disables
preemption for such processors prior to the call and enables it
after the call.
Those functions that needed this fix have been "outlined" to
mips-atomic.c, as they are no longer good candidates for inlining.
This bug was observed in a BMIPS 5000, occuring once every few hours
in a continuous reboot test. It was traced to the write_lock_irq()
function which was being invoked in release_task() in exit.c.
By placing a number of "nops" inbetween the mfc0/mtc0 pair in
arch_local_irq_disable(), which is called by write_lock_irq(), we
were able to greatly increase the occurance of this bug. Similarly,
the application of this commit silenced the bug.
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: Kevin Cernekee cernekee@gmail.com
Cc: Jim Quinlan <jim2101024@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/4321/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The "else clause" of most functions in bitops.h invoked
raw_local_irq_{save,restore}() and in doing so had a dependency on
irqflags.h. This fix moves said code to bitops.c, removing the
dependency.
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: Kevin Cernekee cernekee@gmail.com
Cc: Jim Quinlan <jim2101024@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/4320/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
[ralf@linux-mips.org: No functional change but it's consistent with how
use types elsewhere in the code.]
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: Kevin Cernekee cernekee@gmail.com
Cc: Jim Quinlan <jim2101024@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/4319/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
So far is_compat_task() was testing for 32-bit registers if O32 support
was enabled and if O32 support was disabled but N32 enabled it was testing
for 32-bit address space. So if both O32 and N32 were enabled a N32
task was not considered a compat task, whops.
This still leaves potential cases where O32 and N32 need different treatment
unsolved. But that's another commit.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS fixes from Ralf Baechle:
"Random small fixes across the MIPS code."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: CMP: Fix physical core number calculation logic
MIPS: JZ4740: Forward declare struct uart_port in header.
MIPS: JZ4740: Fix '#include guard' in serial.h
MIPS: hugetlbfs: Fix hazard between tlb write and pagemask restoration.
MIPS: Restore pagemask after dumping the TLB.
MIPS: Hugetlbfs: Handle huge pages correctly in pmd_bad()
MIPS: R5000: Fix TLB hazard handling.
MIPS: tlbex: Deal with re-definition of label
MIPS: Make __{,n,u}delay declarations match definitions and generic delay.h
Place comments in:
arch/mips/include/asm/Kbuild
arch/tile/include/arch/Kbuild
to make them non-empty so that the patch program doesn't remove them when it
reduces them to nothing.
Possibly they should be just deleted, but it's possible that they'll acquire
generic-y or genhdr-y lines in future, so I'm keeping them around for the
moment.
Note that MIPS will compile happily if the file is deleted instead. I haven't
tested TILE, but I suspect it will be the same there.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Ralf Baechle <ralf@linux-mips.org>
cc: Chris Metcalf <cmetcalf@tilera.com>
At some recent point arch/mips/include/asm/delay.h has started being
included into csrc-octeon.c where the __?delay() functions are defined.
This causes a compile failure due to conflicting declarations and
definitions of the functions.
It turns out that the generic definitions in arch/mips/lib/delay.c also
conflict.
Proposed fix: Declare the functions to take unsigned long parameters
just like asm-generic (and x86) does. Update __delay to agree
(__ndelay and __udelay need no change).
Bonus: Get rid of 'inline' from __delay() definition, as it is globally
visible, and the compiler should be making this decision itself (it does
in fact inline the function without being told to).
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4354/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This version contains a few updates by David Daney, in particular it's
now using __builtin_frame_address() instead of asm() which depending
on personal taste, is slightly more appealing.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS update from Ralf Baechle:
"Cleanups and fixes for breakage that occured earlier during this merge
phase. Also a few patches that didn't make the first pull request.
Of those is the Alchemy work that merges code for many of the SOCs and
evaluation boards thus among other code shrinkage, reduces the number
of MIPS defconfigs by 5."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (22 commits)
MIPS: SNI: Switch RM400 serial to SCCNXP driver
MIPS: Remove unused empty_bad_pmd_table[] declaration.
MIPS: MT: Remove kspd.
MIPS: Malta: Fix section mismatch.
MIPS: asm-offset.c: Delete unused irq_cpustat_t struct offsets.
MIPS: Alchemy: Merge PB1100/1500 support into DB1000 code.
MIPS: Alchemy: merge PB1550 support into DB1550 code
MIPS: Alchemy: Single kernel for DB1200/1300/1550
MIPS: Optimize TLB refill for RI/XI configurations.
MIPS: proc: Cleanup printing of ASEs.
MIPS: Hardwire detection of DSP ASE Rev 2 for systems, as required.
MIPS: Add detection of DSP ASE Revision 2.
MIPS: Optimize pgd_init and pmd_init
MIPS: perf: Add perf functionality for BMIPS5000
MIPS: perf: Split the Kconfig option CONFIG_MIPS_MT_SMP
MIPS: perf: Remove unnecessary #ifdef
MIPS: perf: Add cpu feature bit for PCI (performance counter interrupt)
MIPS: perf: Change the "mips_perf_event" table unsupported indicator.
MIPS: Align swapper_pg_dir to 64K for better TLB Refill code.
vmlinux.lds.h: Allow architectures to add sections to the front of .bss
...
Pull module signing support from Rusty Russell:
"module signing is the highlight, but it's an all-over David Howells frenzy..."
Hmm "Magrathea: Glacier signing key". Somebody has been reading too much HHGTTG.
* 'modules-next' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (37 commits)
X.509: Fix indefinite length element skip error handling
X.509: Convert some printk calls to pr_devel
asymmetric keys: fix printk format warning
MODSIGN: Fix 32-bit overflow in X.509 certificate validity date checking
MODSIGN: Make mrproper should remove generated files.
MODSIGN: Use utf8 strings in signer's name in autogenerated X.509 certs
MODSIGN: Use the same digest for the autogen key sig as for the module sig
MODSIGN: Sign modules during the build process
MODSIGN: Provide a script for generating a key ID from an X.509 cert
MODSIGN: Implement module signature checking
MODSIGN: Provide module signing public keys to the kernel
MODSIGN: Automatically generate module signing keys if missing
MODSIGN: Provide Kconfig options
MODSIGN: Provide gitignore and make clean rules for extra files
MODSIGN: Add FIPS policy
module: signature checking hook
X.509: Add a crypto key parser for binary (DER) X.509 certificates
MPILIB: Provide a function to read raw data into an MPI
X.509: Add an ASN.1 decoder
X.509: Add simple ASN.1 grammar compiler
...
Pull pile 2 of execve and kernel_thread unification work from Al Viro:
"Stuff in there: kernel_thread/kernel_execve/sys_execve conversions for
several more architectures plus assorted signal fixes and cleanups.
There'll be more (in particular, real fixes for the alpha
do_notify_resume() irq mess)..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal: (43 commits)
alpha: don't open-code trace_report_syscall_{enter,exit}
Uninclude linux/freezer.h
m32r: trim masks
avr32: trim masks
tile: don't bother with SIGTRAP in setup_frame
microblaze: don't bother with SIGTRAP in setup_rt_frame()
mn10300: don't bother with SIGTRAP in setup_frame()
frv: no need to raise SIGTRAP in setup_frame()
x86: get rid of duplicate code in case of CONFIG_VM86
unicore32: remove pointless test
h8300: trim _TIF_WORK_MASK
parisc: decide whether to go to slow path (tracesys) based on thread flags
parisc: don't bother looping in do_signal()
parisc: fix double restarts
bury the rest of TIF_IRET
sanitize tsk_is_polling()
bury _TIF_RESTORE_SIGMASK
unicore32: unobfuscate _TIF_WORK_MASK
mips: NOTIFY_RESUME is not needed in TIF masks
mips: merge the identical "return from syscall" per-ABI code
...
Conflicts:
arch/arm/include/asm/thread_info.h
The PB1100/1500 are similar to their DB-cousins but with a few
more devices on the bus.
This patch adds PB1100/1500 support to the existing DB1100/1500
code.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: lnux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4338/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Most supported systems currently hardwire cpu_has_dsp to 0, so we also
can disable support for cpu_has_dsp2 resulting in a slightly smaller
kernel.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
[ralf@linux-mips.org: This patch really only detects the ASE and passes its
existence on to userland via /proc/cpuinfo. The DSP ASE Rev 2. adds new
resources but no resources that would need management by the kernel.]
Signed-off-by: Steven J. Hill <sjhill@mips.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4165/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The PCI (Program Counter Interrupt) bit in the "cause" register
is mandatory for MIPS32R2 cores, but has also been added to some R1
cores (BMIPS5000). This change adds a cpu feature bit to make it
easier to check for and use this feature.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/4106/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
I've maintained this patch, originally from Thiemo Seufer in 2004, for a
really long time, but I think it's time for it to get a look at for
possible inclusion. I have had no problems with it across various SGI
systems over the years.
To quote the post here:
http://www.linux-mips.org/archives/linux-mips/2004-12/msg00000.html
"the atomic functions use so far memory references for the inline
assembler to access the semaphore. This can lead to additional
instructions in the ll/sc loop, because newer compilers don't
expand the memory reference any more but leave it to the assembler.
The appended patch uses registers instead, and makes the ll/sc
arguments more explicit. In some cases it will lead also to better
register scheduling because the register isn't bound to an output
any more."
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4029/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All legacy PWM providers have now been moved to the PWM subsystem. The
plan for 3.8 is to adapt all board files to provide a lookup table for
PWM devices in order to get rid of the global namespace. Subsequently,
users of the legacy pwm_request() and pwm_free() functions can be
migrated to the new pwm_get() and pwm_put() functions. Once this has
been completed, the legacy API and the compatibility code in the core
can be removed.
In addition to the above, these changes also add support for configuring
the polarity of a PWM signal (currently only supported on ECAP and
EHRPWM) and include a much needed rework of the i.MX driver. Managed
functions to obtain and release a PWM device (devm_pwm_get() and
devm_pwm_put()) have been added and the pwm-backlight driver has been
updated to use them. If the PWM subsystem hasn't been enabled, dummy
functions are provided that allow the subsystem to safely compile out.
Some common checks on input parameters have been moved to the core and
removed from the drivers. Finally, a small fix corrects the description
of the PWM specifier's second cell in the device tree representation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABAgAGBQJQcV6pAAoJEN0jrNd/PrOh594P/3NHPjnTiyAZpUICX4mJeoMd
1rX685HofCyX5jlHloS1pLRXYtIPZP97We5crNR/k/RujKcHAqAFzLtG2Jj93gxm
nRUwLZ4xbrAgeaZeJV8YG1naWx9R1OjrK2sv+FyHRWsn9UZus2vDMV7tB0oNWo9k
DMhtF1q7gQxx4nRu8z9FFybyItQinVREODNs+Gdv6AOJ36t+mOsGPL3LKZeFsIG3
LdaB1p3t/07Job4KwGYYRjkOR7bIQ+ADnnO8Pkk0a9lxkMI8rA0uFbLwgyx7Hohh
xZtm8R5il2IlHwqh52RzpShceWICxCZ3htuIXTRbVa1PSEsBzZ66W2CT7sy1jPm5
lJlHgc7abaiwijtoG76I+Lgslv5UTViBuIYHSX4dH2kF3Jgm2SgTBNzZYePI5MMT
BI3xc9WnwBpxgMybJsPHfU0Ff6O/9h9ab7q5lBOHkQJittahYxzWD+FgYlalcAa+
I919iFREKNZytewLnXu+4TG0RfacQoj6D5G+SquOGmXyKYRhhJ1O6WodnRZHi/0n
M6J0f6fLxpomI1RMn44VYP43OPJCDYxgXYoDLwCZQL9tSWYpdhXoDrjcIPO547w1
ZS5HTXUE4DrxeYjoeqL555vtQIooM9CuH4JwKlz5zzea8NPC8eVtmNFTTWE6wKWX
ZIOOLVvw/FI0/DSjBb8H
=MQ5V
-----END PGP SIGNATURE-----
Merge tag 'for-3.7-rc1' of git://gitorious.org/linux-pwm/linux-pwm
Pull pwm changes from Thierry Reding:
"All legacy PWM providers have now been moved to the PWM subsystem.
The plan for 3.8 is to adapt all board files to provide a lookup table
for PWM devices in order to get rid of the global namespace.
Subsequently, users of the legacy pwm_request() and pwm_free()
functions can be migrated to the new pwm_get() and pwm_put()
functions. Once this has been completed, the legacy API and the
compatibility code in the core can be removed.
In addition to the above, these changes also add support for
configuring the polarity of a PWM signal (currently only supported on
ECAP and EHRPWM) and include a much needed rework of the i.MX driver.
Managed functions to obtain and release a PWM device (devm_pwm_get()
and devm_pwm_put()) have been added and the pwm-backlight driver has
been updated to use them. If the PWM subsystem hasn't been enabled,
dummy functions are provided that allow the subsystem to safely
compile out.
Some common checks on input parameters have been moved to the core and
removed from the drivers. Finally, a small fix corrects the
description of the PWM specifier's second cell in the device tree
representation."
* tag 'for-3.7-rc1' of git://gitorious.org/linux-pwm/linux-pwm: (23 commits)
pwm: dt: Fix description of second PWM cell
pwm: Check for negative duty-cycle and period
pwm: Add Ingenic JZ4740 support
MIPS: JZ4740: Export timer API
pwm: Move PUV3 PWM driver to PWM framework
unicore32: pwm: Use managed resource allocations
unicore32: pwm: Remove unnecessary indirection
unicore32: pwm: Use module_platform_driver()
unicore32: pwm: Properly remap memory-mapped registers
pwm-backlight: Use devm_pwm_get() instead of pwm_get()
pwm: Move AB8500 PWM driver to PWM framework
pwm: Fix compilation error when CONFIG_PWM is not defined
pwm: i.MX: fix clock lookup
pwm: i.MX: use per clock unconditionally
pwm: i.MX: add devicetree support
pwm: i.MX: Use module_platform_driver
pwm: i.MX: add functions to enable/disable pwm.
pwm: i.MX: remove unnecessary if in pwm_[en|dis]able
pwm: i.MX: factor out SoC specific functions
pwm: pwm-tiehrpwm: Add support for configuring polarity of PWM
...
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Merge patches from Andrew Morton:
"A few misc things and very nearly all of the MM tree. A tremendous
amount of stuff (again), including a significant rbtree library
rework."
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (160 commits)
sparc64: Support transparent huge pages.
mm: thp: Use more portable PMD clearing sequenece in zap_huge_pmd().
mm: Add and use update_mmu_cache_pmd() in transparent huge page code.
sparc64: Document PGD and PMD layout.
sparc64: Eliminate PTE table memory wastage.
sparc64: Halve the size of PTE tables
sparc64: Only support 4MB huge pages and 8KB base pages.
memory-hotplug: suppress "Trying to free nonexistent resource <XXXXXXXXXXXXXXXX-YYYYYYYYYYYYYYYY>" warning
mm: memcg: clean up mm_match_cgroup() signature
mm: document PageHuge somewhat
mm: use %pK for /proc/vmallocinfo
mm, thp: fix mlock statistics
mm, thp: fix mapped pages avoiding unevictable list on mlock
memory-hotplug: update memory block's state and notify userspace
memory-hotplug: preparation to notify memory block's state at memory hot remove
mm: avoid section mismatch warning for memblock_type_name
make GFP_NOTRACK definition unconditional
cma: decrease cc.nr_migratepages after reclaiming pagelist
CMA: migrate mlocked pages
kpageflags: fix wrong KPF_THP on non-huge compound pages
...
The core page allocator ensures that page flags are zeroed when freeing
pages via free_pages_check. A number of architectures (ARM, PPC, MIPS)
rely on this property to treat new pages as dirty with respect to the data
cache and perform the appropriate flushing before mapping the pages into
userspace.
This can lead to cache synchronisation problems when using hugepages,
since the allocator keeps its own pool of pages above the usual page
allocator and does not reset the page flags when freeing a page into the
pool.
This patch adds a new architecture hook, arch_clear_hugepage_flags, so
that architectures which rely on the page flags being in a particular
state for fresh allocations can adjust the flags accordingly when a page
is freed into the pool.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: Michal Hocko <mhocko@suse.cz>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull MIPS update from Ralf Baechle:
"This is the MIPS update for 3.7.
A fair chunk of them are platform updates to the Cavium Octeon SOC
(which involves machine generated header files of considerable size),
Atheros ATH79xx, RMI aka Netlogic aka Broadcom XLP, Broadcom BCM63xx
platforms.
Support for the commercial MIPS simulator MIPSsim has been removed as
MIPS Technologies is shifting away from this product and Qemu is
offering various more powerful platforms. The generic MIPS code can
now also probe for no-execute / write-only TLB features implemented
without the full SmartMIPS extension as permitted by the latest MIPS
processor architecture. Lots of small changes to generic code."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (78 commits)
MIPS: ath79: Fix CPU/DDR frequency calculation for SRIF PLLs
MIPS: ath79: use correct fractional dividers for {CPU,DDR}_PLL on AR934x
MIPS: BCM63XX: Properly handle mac address octet overflow
MIPS: Kconfig: Avoid build errors by hiding USE_OF from the user.
MIPS: Replace `-' in defconfig filename wth `_' for consistency.
MIPS: Wire kcmp syscall.
MIPS: MIPSsim: Remove the MIPSsim platform.
MIPS: NOTIFY_RESUME is not needed in TIF masks
MIPS: Merge the identical "return from syscall" per-ABI code
MIPS: Unobfuscate _TIF..._MASK
MIPS: Prevent hitting do_notify_resume() with !user_mode(regs).
MIPS: Replace 'kernel_uses_smartmips_rixi' with 'cpu_has_rixi'.
MIPS: Add base architecture support for RI and XI.
MIPS: Optimise TLB handlers for MIPS32/64 R2 cores.
MIPS: uasm: Add INS and EXT instructions.
MIPS: Avoid pipeline stalls on some MIPS32R2 cores.
MIPS: Make VPE count to be one-based.
MIPS: Add new end of interrupt functionality for GIC.
MIPS: Add EIC support for GIC.
MIPS: Code clean-ups for the GIC.
...
This commit moves the driver to drivers/pwm and converts it to the new
PWM framework.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
This is a prerequisite for allowing the PWM driver to be converted to
the PWM framework.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
This is a preparatory patch for the introduction of NT_SIGINFO elf note.
Make the location of compat_siginfo_t uniform across eight architectures
which have it. Now it can be pulled in by including asm/compat.h or
linux/compat.h.
Most of the copies are verbatim. compat_uid[32]_t had to be replaced by
__compat_uid[32]_t. compat_uptr_t had to be moved up before
compat_siginfo_t in asm/compat.h on a several architectures (tile already
had it moved up). compat_sigval_t had to be relocated from linux/compat.h
to asm/compat.h.
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Amerigo Wang <amwang@redhat.com>
Cc: "Jonathan M. Foote" <jmfoote@cert.org>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert #include "..." to #include <path/...> in kernel system headers.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Make default just return 0. The current default (checking
TIF_POLLING_NRFLAG) is taken to architectures that need it;
ones that don't do polling in their idle threads don't need
to defined TIF_POLLING_NRFLAG at all.
ia64 defined both TS_POLLING (used by its tsk_is_polling())
and TIF_POLLING_NRFLAG (not used at all). Killed the latter...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Besides the CPU and DDR PLLs, the CPU and DDR frequencies
can be derived from other PLLs in the SRIF block on the
AR934x SoCs. The current code does not checks if the SRIF
PLLs are used and this can lead to incorrectly calculated
CPU/DDR frequencies.
Fix it by calculating the frequencies from SRIF PLLs if
those are used on a given board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: <stable@vger.kernel.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4324/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the mapping of Elf_[SPE]hdr, Elf_Addr, Elf_Sym, Elf_Dyn, Elf_Rel/Rela,
ELF_R_TYPE() and ELF_R_SYM() to either the 32-bit version or the 64-bit version
into asm-generic/module.h for all arches bar MIPS.
Also, use the generic definition mod_arch_specific where possible.
To this end, I've defined three new config bools:
(*) HAVE_MOD_ARCH_SPECIFIC
Arches define this if they don't want to use the empty generic
mod_arch_specific struct.
(*) MODULES_USE_ELF_RELA
Arches define this if their modules can contain RELA records. This causes
the Elf_Rela mapping to be emitted and allows apply_relocate_add() to be
defined by the arch rather than have the core emit an error message.
(*) MODULES_USE_ELF_REL
Arches define this if their modules can contain REL records. This causes
the Elf_Rel mapping to be emitted and allows apply_relocate() to be
defined by the arch rather than have the core emit an error message.
Note that it is possible to allow both REL and RELA records: m68k and mips are
two arches that do this.
With this, some arch asm/module.h files can be deleted entirely and replaced
with a generic-y marker in the arch Kbuild file.
Additionally, I have removed the bits from m32r and score that handle the
unsupported type of relocation record as that's now handled centrally.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The MIPSsim platform is no longer supported or used.
[ralf@linux-mips.org: Also remove mipssim from arch/mips/Kbuild.platforms
and delete arch/mips/include/asm/mach-mipssim/*.]
Signed-off-by: Steven J. Hill <sjhill@mips.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4350/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If it's set, SIGPENDING is also set. And SIGPENDING is present in
the masks...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove usage of the 'kernel_uses_smartmips_rixi' macro from all files
and use new 'cpu_has_rixi' instead.
Signed-off-by: Steven J. Hill <sjhill@mips.com>
Acked-by: David Daney <david.daney@cavium.com>
Originally both Read Inhibit (RI) and Execute Inhibit (XI) were
supported by the TLB only for a SmartMIPS core. The MIPSr3(TM)
Architecture now defines an optional feature to implement these
TLB bits separately. Support for one or both features can be
checked by looking at the Config3.RXI bit.
Signed-off-by: Steven J. Hill <sjhill@mips.com>
Acked-by: David Daney <david.daney@cavium.com>
The GIC interrupt code is used by multiple platforms and the
current code was half Malta dependent code. These changes
abstract away the platform specific differences.
Signed-off-by: Steven J. Hill <sjhill@mips.com>
More information about the SEAD-3 platform can be found at
<http://www.mips.com/products/development-kits/mips-sead-3/>
on MTI's site. Currently, the M14K family of cores is what
the SEAD-3 is utilised with.
Signed-off-by: Douglas Leung <douglas@mips.com>
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Steven J. Hill <sjhill@mips.com>
The gpio_chip struct allows us to set a .to_irq callback. Once this is set
we can rely on the generic __gpio_to_irq() function to map gpio->irq allowing
more than one gpio_chip to register an interrupt
Signed-off-by: John Crispin <blogic@openwrt.org>
Implement support for pinctrl on lantiq/falcon socs. The FALCON has 5 banks
of up to 32 pins.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
The cn68XX has a new interrupt controller named CIU2, add support for
this, and use it if cn68XX detected at runtime.
Signed-off-by: David Daney <david.daney@cavium.com>
Add support for cn68xx, cn61xx, cn63xx, cn66xx and cnf71XX.
Add little-endian register layouts.
Patch cvmx-interrupt-rsl.c for changed definition.
Signed-off-by: David Daney <david.daney@cavium.com>
Also add cvmx_get_octeon_family().
Both of these are needed by the upcoming register definition refresh
patch.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Reviewed-by: Jonas Gorski <jonas.gorski@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/4111/
Signed-off-by: John Crispin <blogic@openwrt.org>
OHCI/EHCI are in the high (second) word. Not currently used by any
driver.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/4026/
Signed-off-by: John Crispin <blogic@openwrt.org>
The USB 2.0 device depends on some functionality in other blocks, such
as GPIO and USBH. Add those register definitions here.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/4025/
Signed-off-by: John Crispin <blogic@openwrt.org>
The "IUDMA" engine used by bcm63xx_enet is also used by other blocks,
such as the USB 2.0 device. Move the definitions into a common file so
that they do not need to be duplicated in each driver.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/4082/
Signed-off-by: John Crispin <blogic@openwrt.org>
These were erroneously copied from BCM6368. BCM6328 does not expose the
ENETSW_TXDMA interrupts, and BCM_6328_HIGH_IRQ_BASE + 7 is actually used
for the second UART.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/4090/
Signed-off-by: John Crispin <blogic@openwrt.org>
Add the missing definitions for BCM6345.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/4091/
Signed-off-by: John Crispin <blogic@openwrt.org>
Up to now all our SoCs had the 5 IM ranges in a consecutive order. To accomodate
the SVIP we need to support IM ranges that are scattered inside the register range.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4237/
Needed by SPI driver.
Signed-off-by: David Daney <david.daney@cavium.com>
Patchwork: http://patchwork.linux-mips.org/patch/3796/
Signed-off-by: John Crispin <blogic@openwrt.org>
The ath79 platform code allows to run a single kernel image on various
SoCs which are based on the 24Kc and 74Kc cores. The current code
explicitely disables the DSP ASE, but that is available in the 74Kc core.
Remove the override in order to let the kernel to detect the availability
of the DSP ASE at runtime.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4222/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current implementation of synchronise_count_{master,slave} blocks
slave CPUs in early boot until all of them come up. This no longer
works because blocking a CPU with interrupts off after notifying the
CPU to be online causes problems with the current kernel.
Specifically, after the workqueue changes
(commit a08489c569 "Pull workqueue changes from Tejun Heo")
the CPU_ONLINE notification callback workqueue_cpu_up_callback()
will hang on wait_for_completion(&idle_rebind.done), if the slave
CPUs are blocked for synchronize_count_slave().
The changes are to update synchronize_count_{master,slave}() to handle
one CPU at a time and to call synchronise_count_master() in __cpu_up()
so that the CPU_ONLINE notification goes out only after the COP0 COUNT
register is synchronized.
[ralf@linux-mips.org: This matter only to those few platforms which are
using the cp0 counter as their clocksource which are XLP, XLR and MIPS'
CMP solution.]
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4216/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
BCM6338 and BCM6348 have a message control register width of 8 bits, instead
of 16-bits like what the SPI driver assumes right now. Also the SPI message
type shift value of 14 is actually 6 for these SoCs.
This resulted in transmit FIFO corruption because we were writing 16-bits
to an 8-bits wide register, thus spanning on the first byte of the transmit
FIFO, which had already been filed in bcm63xx_spi_fill_txrx_fifo().
Fix this by passing the message control register width and message type
shift through platform data back to the SPI driver so that it can use
it properly.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: grant.likely@secretlab.ca
Cc: spi-devel-general@lists.sourceforge.net
Cc: jonas.gorski@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/3983/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The relocation code was essentially taken from the 2.4 modutils which
perform relocation in userspace. In 2.6 relocation of multiple modules
may be performed in parallel by the in-kernel loader so the global
variable mips_hi16_list won't fly anymore. Fix race by moving it into
mod_arch_specific.
[ralf@linux-mips.org: folded in Tony's followup fix. Thanks Tony!]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Tony Wu <tung7970@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/4189/
Since 3.6.0-rc1, We are getting many messages like:
WARNING: at kernel/irq/irqdomain.c:444 irq_domain_associate_many+0x23c/0x260()
Modules linked in:
Call Trace:
[<ffffffff814cb698>] dump_stack+0x8/0x34
[<ffffffff81133d00>] warn_slowpath_common+0x78/0xa8
[<ffffffff81187e44>] irq_domain_associate_many+0x23c/0x260
[<ffffffff81187f38>] irq_create_mapping+0xd0/0x220
[<ffffffff81188104>] irq_create_of_mapping+0x7c/0x158
[<ffffffff813e5f08>] irq_of_parse_and_map+0x28/0x40
.
.
.
Both the CIU and GPIO interrupt domains were somewhat screwed up.
For the CIU domain, we need to call irq_domain_associate() for each of
the preassigned irq numbers. For the GPIO domain, we were applying
the register bit offset in octeon_irq_gpio_xlat, but it should be done
in octeon_irq_gpio_map instead.
Also: Reserve all 8 'core' irqs for the 'core' irq_chip so that they
don't get used by the other domains. Remove unused OCTEON_IRQ_*
symbols.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4190/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For unexplainable reasons the Loongson 2 clock API was implemented in a
module so fixing this involved shifting large amounts of code around.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Merge Andrew's first set of patches:
"Non-MM patches:
- lots of misc bits
- tree-wide have_clk() cleanups
- quite a lot of printk tweaks. I draw your attention to "printk:
convert the format for KERN_<LEVEL> to a 2 byte pattern" which
looks a bit scary. But afaict it's solid.
- backlight updates
- lib/ feature work (notably the addition and use of memweight())
- checkpatch updates
- rtc updates
- nilfs updates
- fatfs updates (partial, still waiting for acks)
- kdump, proc, fork, IPC, sysctl, taskstats, pps, etc
- new fault-injection feature work"
* Merge emailed patches from Andrew Morton <akpm@linux-foundation.org>: (128 commits)
drivers/misc/lkdtm.c: fix missing allocation failure check
lib/scatterlist: do not re-write gfp_flags in __sg_alloc_table()
fault-injection: add tool to run command with failslab or fail_page_alloc
fault-injection: add selftests for cpu and memory hotplug
powerpc: pSeries reconfig notifier error injection module
memory: memory notifier error injection module
PM: PM notifier error injection module
cpu: rewrite cpu-notifier-error-inject module
fault-injection: notifier error injection
c/r: fcntl: add F_GETOWNER_UIDS option
resource: make sure requested range is included in the root range
include/linux/aio.h: cpp->C conversions
fs: cachefiles: add support for large files in filesystem caching
pps: return PTR_ERR on error in device_create
taskstats: check nla_reserve() return
sysctl: suppress kmemleak messages
ipc: use Kconfig options for __ARCH_WANT_[COMPAT_]IPC_PARSE_VERSION
ipc: compat: use signed size_t types for msgsnd and msgrcv
ipc: allow compat IPC version field parsing if !ARCH_WANT_OLD_COMPAT_IPC
ipc: add COMPAT_SHMLBA support
...
Rather than #define the options manually in the architecture code, add
Kconfig options for them and select them there instead. This also allows
us to select the compat IPC version parsing automatically for platforms
using the old compat IPC interface.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds basic platform devices for Loongson 1B, including serial port,
ethernet, USB, RTC and interrupt handler.
The Loongson 1B UART is compatible with NS16550A, the Loongson 1B GMAC is
built around a Synopsys IP Core.
Use normal instead of enhanced descriptors.
Thanks to Giuseppe for updating the normal descriptor in stmmac driver.
Thanks to Zhao Zhang for implementing the RTC driver.
Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: wuzhangjin@gmail.com
Cc: zhzhl555@gmail.com
Cc: Kelvin Cheung <keguang.zhang@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/4133/
Patchwork: https://patchwork.linux-mips.org/patch/4134/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On XLP, the dcache size depends on the number of enabled threads in
core. There are no dcache aliases if the pagesize is large enough or
if enough threads are enabled in the core.
Remove the #define for cpu_has_dc_aliases and leave it to be computed
at runtime.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4099/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The XLP USB controller appears as a device on the internal SoC PCIe
bus, the block has 2 EHCI blocks and 4 OHCI blocks. Change are to:
* Add files netlogic/xlp/usb-init.c and asm/netlogic/xlp-hal/usb.h
to initialize the USB controller and define PCI fixups. The PCI
fixups are to setup interrupts and DMA mask.
* Update include/asm/xlp-hal/{iomap.h,pic.h,xlp.h} to add interrupt
mapping for EHCI/OHCI interrupts.
Signed-off-by: Ganesan Ramalingam <ganesanr@netlogicmicro.com>
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3756/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Adds support for the XLP on-chip PCIe controller. On XLP, the
on-chip devices(including the 4 PCIe links) appear in the PCIe
configuration space of the XLP as PCI devices.
The changes are to initialize and register the PCIe controller,
enable hardware byte swap in the PCIe IO and MEM space, and to
enable PCIe interrupts.
Signed-off-by: Ganesan Ramalingam <ganesanr@netlogicmicro.com>
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3760/
Patchwork: https://patchwork.linux-mips.org/patch/4104/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Changes to add support for the boot NOR flash on XLR boards and the
boot NAND/NOR flash drivers on the XLS boards.
Signed-off-by: Ganesan Ramalingam <ganesanr@netlogicmicro.com>
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3758/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove NETLOGIC_ prefix from gpio register definitions, this will
bring it in-line with the other Netlogic headers.
Having NETLOGIC prefix here is misleading because these are XLR/XLS
specific register definitions.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3754/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Update for core intialization code. Initialize status register
after receiving NMI for CPU wakeup. Add the low level L1D flush
code before enabling threads in core.
Also convert the ehb to _ehb so that it works under more GCC
versions.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3755/
Patchwork: https://patchwork.linux-mips.org/patch/4095/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for the PCIe port found on BCM6328.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/3956/
Reviewed-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This includes CPU speed, memory size detection and working UART, but
lacking the appropriate drivers, no support for attached flash.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/3951/
Reviewed-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On BCM6358 and BCM6368 the attached flash type is exposed through a
bootstrapping register. Use it for auto detecting the flash type on
those and default to parallel flash for earlier SoCs.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/3954/
Reviewed-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson 1B is a 32-bit SoC designed by Institute of Computing Technology
(ICT) and the Chinese Academy of Sciences (CAS), which implements the
MIPS32 release 2 instruction set.
[ralf@linux-mips.org: But which is not strictly a MIPS32 compliant device
which also is why it identifies itself with the Legacy Vendor ID in the
PrID register. When applying the patch I shoveled some code around to
keep things in alphabetical order and avoid forward declarations.]
Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Cc: To: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: wuzhangjin@gmail.com
Cc: zhzhl555@gmail.com
Cc: Kelvin Cheung <keguang.zhang@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/3976/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The platform data can now specify which external memory banks to probe
for NAND chips, and in which order. Banks that contain a NAND are used
and the other banks are freed.
Squashed version of development done in jz-2.6.38 branch.
Original patch by Lars-Peter Clausen with some bug fixes from me.
Thanks to Paul Cercueil for the initial autodetection patch.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3560/
Acked-By: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A number of new instructions have been added to the micro assembler causing
the list to no longer be in alphabetical order. This patch fixes up the name
ordering.
Signed-off-by: Steven J. Hill <sjhill@mips.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3789/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We can save the 451 lines of code that comprise memcpy-inatomic.S at the
expense of a single instruction in the memcpy prolog. We also use an
additional register (t6), so this may cause increased register pressure in
some places as well. But I think the reduced maintenance burden, of not
having two nearly identical implementations, makes it worth it.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There are three parts to this:
1) Remove the definitions of OCTEON_IRQ_TWSI and OCTEON_IRQ_TWSI2.
The interrupts are specified by the device tree and these hard
coded irq numbers block the used of the irq lines by the irq_domain
code.
2) Remove platform device setup code from octeon-platform.c, it is
now unused.
3) Convert i2c-octeon.c to use device tree. Part of this includes
using the devm_* functions instead of the raw counterparts, thus
simplifying error handling. No functionality is changed.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: linux-mips@linux-mips.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/3939/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The follow-on patch to add irq_domain support will be the supported
method for using these irq lines, so get these defines out of the way
in preperation for that.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3930/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This symbol will be removed, so don't use it as part of the definition of
OCTEON_IRQ_LAST.
Set OCTEON_IRQ_LAST to 127 so there is space for all the automatically
allocated (via irq_domain) irqs.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3946/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds the necessary stub to register the SPI platform driver.
Since the registers are shuffled between the 4 BCM63xx CPUs supported by
this SPI driver we also need to generate the internal register layout and
export this layout for the driver to use it properly.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: grant.likely@secretlab.ca
Cc: spi-devel-general@lists.sourceforge.net
Patchwork: https://patchwork.linux-mips.org/patch/3321/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This register was introduced with the support of the BCM6368 CPU in the idea
that its internal layout was different from the other CPUs SPI controller.
The controller is actually the same as the one present on BCM6358 so we can
remove this register and use the usual SPI register instead.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: grant.likely@secretlab.ca
Cc: spi-devel-general@lists.sourceforge.net
Patchwork: https://patchwork.linux-mips.org/patch/3316/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the _CLK suffix from the BCM6368 clock bits definitions to be
consistent with what is already present.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3312/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit: 3777808873 [bug.h: need linux/kernel.h
for TAINT_WARN.] breaks all MIPS builds.
CC arch/mips/kernel/machine_kexec.o
In file included from include/linux/kernel.h:20:0,
from include/asm-generic/bug.h:35,
from /home/yuasa/src/linux/kernel/git/linux-2.6/arch/mips/include/asm/bug.h:41,
from /home/yuasa/src/linux/kernel/git/linux-2.6/arch/mips/include/asm/bitops.h:20,
from include/linux/bitops.h:22,
from include/linux/signal.h:38,
from include/linux/elfcore.h:5,
from include/linux/kexec.h:60,
from arch/mips/kernel/machine_kexec.c:9:
include/linux/log2.h: In function '__ilog2_u32':
include/linux/log2.h:34:2: error: implicit declaration of function 'fls' [-Werror=implicit-function-declaration]
include/linux/log2.h: In function '__ilog2_u64':
include/linux/log2.h:42:2: error: implicit declaration of function 'fls64' [-Werror=implicit-function-declaration]
include/linux/log2.h: In function '__roundup_pow_of_two':
include/linux/log2.h:63:2: error: implicit declaration of function 'fls_long' [-Werror=implicit-function-declaration]
In file included from include/linux/bitops.h:22:0,
from include/linux/signal.h:38,
from include/linux/elfcore.h:5,
from include/linux/kexec.h:60,
from arch/mips/kernel/machine_kexec.c:9:
/home/yuasa/src/linux/kernel/git/linux-2.6/arch/mips/include/asm/bitops.h: At top level:
/home/yuasa/src/linux/kernel/git/linux-2.6/arch/mips/include/asm/bitops.h:615:19: error: static declaration of 'fls' follows non-static declaration
include/linux/log2.h:34:9: note: previous implicit declaration of 'fls' was here
In file included from /home/yuasa/src/linux/kernel/git/linux-2.6/arch/mips/include/asm/bitops.h:651:0,
from include/linux/bitops.h:22,
from include/linux/signal.h:38,
from include/linux/elfcore.h:5,
from include/linux/kexec.h:60,
from arch/mips/kernel/machine_kexec.c:9:
include/asm-generic/bitops/fls64.h:18:28: error: static declaration of 'fls64' follows non-static declaration
include/linux/log2.h:42:9: note: previous implicit declaration of 'fls64' was here
In file included from include/linux/signal.h:38:0,
from include/linux/elfcore.h:5,
from include/linux/kexec.h:60,
from arch/mips/kernel/machine_kexec.c:9:
include/linux/bitops.h:160:24: error: conflicting types for 'fls_long'
include/linux/log2.h:63:16: note: previous implicit declaration of 'fls_long' was here
cc1: all warnings being treated as errors
make[2]: *** [arch/mips/kernel/machine_kexec.o] Error 1
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: yuasa@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Linuxppc-dev <linuxppc-dev@ozlabs.org>
Cc: Linux MIPS Mailing List <linux-mips@linux-mips.org>
Cc: Linux-sh list <linux-sh@vger.kernel.org>
Cc: Chris Zankel <chris@zankel.net>
Patchwork: https://patchwork.linux-mips.org/patch/4000/
Tested-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix the following build breakage in v3.4-rc1:
CC kernel/irq_work.o
In file included from include/linux/irq_work.h:4:0,
from kernel/irq_work.c:10:
include/linux/llist.h: In function 'llist_del_all':
include/linux/llist.h:178:2: error: implicit declaration of function 'BUILD_BUG_ON' [-Werror=implicit-function-declaration]
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3568/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Improper alignment can lead to unbootable systems and/or random
crashes.
[ralf@linux-mips.org: This is a lond standing bug since
6eb10bc9e2 (kernel.org) rsp.
c422a10917f75fd19fa7fe070aaaa23e384dae6f (lmo) [MIPS: Clean up linker script
using new linker script macros.] so dates back to 2.6.32.]
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/3881/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
[ralf@linux-mips.org: Cosmetic changes; also fixed up r2300_switch.S and
octeon_switch.S which needed similar modifications.]
Signed-off-by: Leonid Yegoshin <yegoshin@mips.com>
Signed-off-by: Steven J. Hill <sjhill@mips.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3784/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It's a bloody bog standard MIPS64R2 core with just a new PrId ID. Iow
that essentially means Linux just panics because it doesn't know how to
name the core.
[ralf@linux-mips.org: Split original patch into several smaller patches.]
Signed-off-by: Leonid Yegoshin <yegoshin@mips.com>
Signed-off-by: Steven J. Hill <sjhill@mips.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3792/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This change adds macros for routing of GIC interrupts for EIC and
non-EIC hardware modes. Also added Malta GIC macros having to do
with performance and timer interrupts.
Signed-off-by: Steven J. Hill <sjhill@mips.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3576/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Based on https://patchwork.linux-mips.org/patch/3576 - but this really
deserves its own patchset and the symbol should also be used :)
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull vfs changes from Al Viro.
"A lot of misc stuff. The obvious groups:
* Miklos' atomic_open series; kills the damn abuse of
->d_revalidate() by NFS, which was the major stumbling block for
all work in that area.
* ripping security_file_mmap() and dealing with deadlocks in the
area; sanitizing the neighborhood of vm_mmap()/vm_munmap() in
general.
* ->encode_fh() switched to saner API; insane fake dentry in
mm/cleancache.c gone.
* assorted annotations in fs (endianness, __user)
* parts of Artem's ->s_dirty work (jff2 and reiserfs parts)
* ->update_time() work from Josef.
* other bits and pieces all over the place.
Normally it would've been in two or three pull requests, but
signal.git stuff had eaten a lot of time during this cycle ;-/"
Fix up trivial conflicts in Documentation/filesystems/vfs.txt (the
'truncate_range' inode method was removed by the VM changes, the VFS
update adds an 'update_time()' method), and in fs/btrfs/ulist.[ch] (due
to sparse fix added twice, with other changes nearby).
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (95 commits)
nfs: don't open in ->d_revalidate
vfs: retry last component if opening stale dentry
vfs: nameidata_to_filp(): don't throw away file on error
vfs: nameidata_to_filp(): inline __dentry_open()
vfs: do_dentry_open(): don't put filp
vfs: split __dentry_open()
vfs: do_last() common post lookup
vfs: do_last(): add audit_inode before open
vfs: do_last(): only return EISDIR for O_CREAT
vfs: do_last(): check LOOKUP_DIRECTORY
vfs: do_last(): make ENOENT exit RCU safe
vfs: make follow_link check RCU safe
vfs: do_last(): use inode variable
vfs: do_last(): inline walk_component()
vfs: do_last(): make exit RCU safe
vfs: split do_lookup()
Btrfs: move over to use ->update_time
fs: introduce inode operation ->update_time
reiserfs: get rid of resierfs_sync_super
reiserfs: mark the superblock as dirty a bit later
...
Pull MIPS updates from Ralf Baechle:
"The whole series has been sitting in -next for quite a while with no
complaints. The last change to the series was before the weekend the
removal of an SPI patch which Grant - even though previously acked by
himself - appeared to raise objections. So I removed it until the
situation is clarified. Other than that all the patches have the acks
from their respective maintainers, all MIPS and x86 defconfigs are
building fine and I'm not aware of any problems introduced by this
series.
Among the key features for this patch series is a sizable patchset for
Lantiq which among other things introduces support for Lantiq's
flagship product, the FALCON SOC. It also means that the opensource
developers behind this patchset have overtaken Lantiq's competing
inhouse development team that was working behind closed doors.
Less noteworthy the ath79 patchset which adds support for a few more
chip variants, cleanups and fixes. Finally the usual dose of tweaking
of generic code."
Fix up trivial conflicts in arch/mips/lantiq/xway/gpio_{ebu,stp}.c where
printk spelling fixes clashed with file move and eventual removal of the
printk.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (81 commits)
MIPS: lantiq: remove orphaned code
MIPS: Remove all -Wall and almost all -Werror usage from arch/mips.
MIPS: lantiq: implement support for FALCON soc
MTD: MIPS: lantiq: verify that the NOR interface is available on falcon soc
MTD: MIPS: lantiq: implement OF support
watchdog: MIPS: lantiq: implement OF support and minor fixes
SERIAL: MIPS: lantiq: implement OF support
GPIO: MIPS: lantiq: convert gpio-stp-xway to OF
GPIO: MIPS: lantiq: convert gpio-mm-lantiq to OF and of_mm_gpio
GPIO: MIPS: lantiq: move gpio-stp and gpio-ebu to the subsystem folder
MIPS: pci: convert lantiq driver to OF
MIPS: lantiq: convert dma to platform driver
MIPS: lantiq: implement support for clkdev api
MIPS: lantiq: drop ltq_gpio_request() and gpio_to_irq()
OF: MIPS: lantiq: implement irq_domain support
OF: MIPS: lantiq: implement OF support
MIPS: lantiq: drop mips_machine support
OF: PCI: const usage needed by MIPS
MIPS: Cavium: Remove smp_reserve_lock.
MIPS: Move cache setup to setup_arch().
...
Now that all drivers are converted to OF we are able to remove some remaining
pieces of orphaned code.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3841/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
