Add accessor macros for the Memory Accessibility Attribute Registers
(MAARs), the bits contained within the MAARs & the Config5.MRP bit
indicating their presence. The only current use of the MAARs is to
enable speculative accesses to regions of memory. Besides the potential
performance benefits of speculative accesses, they are a requirement
for the P5600 core to handle non-128b-aligned MSA vector loads & stores
rather than generating an address error.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7329/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The MSA specification upon first read appears to suggest that it is safe
to perform vector loads & stores with arbitrary alignment. However it
leaves provision for "address-dependent exceptions"... Align the vector
context to a 16 byte boundary to ensure that the kernel cannot cause any
such exceptions.
Note that the fpu field of struct thread_struct was already at a 16 byte
boundary within the struct, the introduction of FPU_ALIGN simply makes
the requirement explicit. The only part of this impacting the generated
kernel binary is ARCH_MIN_TASKALIGN.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7308/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Preemption must be disabled throughout the process of enabling the FPU,
enabling MSA & initialising the vector registers. Without doing so it
is possible to lose the FPU or MSA whilst initialising them causing
that initialisation to fail.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7307/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit d96cc3d1ec "MIPS: Add microMIPS MSA support." attempted to use
the value of a macro within an inline asm statement but instead emitted
a comment leading to the cfcmsa & ctcmsa instructions being omitted. Fix
that by passing CFC_MSA_INSN & CTC_MSA_INSN as arguments to the asm
statements.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7305/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When a task first makes use of MSA we need to ensure that the upper
64b of the vector registers are set to some value such that no
information can be leaked to it from the previous task to use MSA
context on the CPU. The architecture formerly specified that these
bits would be cleared to 0 when a scalar FP instructions wrote to the
aliased FP registers, which would have implicitly handled this as the
kernel restored scalar FP context. However more recent versions of the
specification now state that the value of the bits in such cases is
unpredictable. Initialise them explictly to be sure, and set all the
bits to 1 rather than 0 for consistency with the least significant
64b.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7497/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The kernel depends upon MSA never being enabled when the FPU is not, a
condition which is currently violated in a few places (whilst saving
sigcontext, following mips_cpu_save). Catch all the problem cases by
disabling MSA in lose_fpu, after saving context if necessary.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7302/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
I added a field for the MSACSR register in struct mips_fpu_struct, but
never actually made use of it... This is a clear bug. Save and restore
the MSACSR register along with the vector registers.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7300/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Just #ifdef away the C functions when included from an assembly file,
as will be done in a following commit.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7299/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a definition for D-Link DSR-1000N router. The bootloader on this board
supplies 20006 in the bootinfo; the enum CVMX_BOARD_TYPE_CUST_DSR1000N
comes from the GPL sources of the board.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: David Daney <ddaney.cavm@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7217/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The GICBIS macro could update the GIC registers incorrectly, depending
on the data value passed in:
* Bits were only OR'd into the register data, so register fields could
not be cleared.
* Bits were OR'd into the register data without masking the data to the
correct field width, corrupting adjacent bits.
Signed-off-by: Jeffrey Deans <jeffrey.deans@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7378/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move most of the functionality of gic_get_int() into a new function
gic_get_int_mask() which takes a bitmask of interrupts in which the
caller is interested, and returns the subset which are pending for the
current CPU.
This allows CP0 IRQ dispatch routines to check only the GIC interrupts
which are routed to a particular CPU interrupt input.
gic_get_int() is reimplemented using gic_get_int_mask() and is retained
for use by any platforms for which gic_get_int() is sufficient.
Signed-off-by: Jeffrey Deans <jeffrey.deans@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7376/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
irq-gic.c:gic_get_int() masks out interrupts from the pending set which
aren’t in the pcpu_mask. Only interrupts marked with GIC_FLAG_IPI were
set in pcpu_mask, meaning that peripheral interrupts also had to be
marked as IPIs. Remove the use of GIC_FLAG_IPI and allow the flags
member of struct gic_intr_map to be zero.
Signed-off-by: Jeffrey Deans <jeffrey.deans@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7374/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The value of GIC_NUM_INTRS is platform-specific. Using a default value
from gic.h will result in incorrect behaviour on some systems, so
require a suitable definition to be present in the platform's irq.h.
Signed-off-by: Jeffrey Deans <jeffrey.deans@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7373/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Several bitmaps are declared in arch/mips/include/asm/gic.h, but the
scope of their use is limited to arch/mips/kernel/irq-gic.c. Move the
declarations from the header file to the C file.
Signed-off-by: Jeffrey Deans <jeffrey.deans@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7372/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Detect if the core supports unique exception codes for the
Read-Inhibit and Execute-Inhibit exceptions and set the
option accordingly. The RI/XI exception support is detected
by setting the 27th bit (IEC) of the PageGrain C0 register
and reading back the value of that register to verify the
bit is enabled.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7340/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPSr5 added support for unique exception codes for the Read-Inhibit
and Execute-Inhibit exceptions.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7338/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Hardware Page Table Walker aims to speed up TLB refill exceptions
by handling them in the hardware level instead of having a software
TLB refill handler. However, a TLB refill exception can still be
thrown in certain cases such as, synchronus exceptions, or address
translation or memory errors during the HTW operation. As a result of
which, HTW must not be considered a complete replacement for the TLB
refill software handler, but rather a fast-path for it.
For HTW to work, the PWBase register must contain the task's page
global directory address so the HTW will kick in on TLB refill
exceptions.
Due to HTW being a separate engine embedded deep in the CPU pipeline,
we need to restart the HTW everytime a PTE changes to avoid HTW
fetching a old entry from the page tables. It's also necessary to
restart the HTW on context switches to prevent it from fetching a
page from the previous process. Finally, since HTW is using the
entryhi register to write the translations to the TLB, it's necessary
to stop the HTW whenever the entryhi changes (eg for tlb probe
perations) and enable it back afterwards.
== Performance ==
The following trivial test was used to measure the performance of the
HTW. Using the same root filesystem, the following command was used
to measure the number of tlb refill handler executions with and
without (using 'nohtw' kernel parameter) HTW support. The kernel was
modified to use a scratch register as a counter for the TLB refill
exceptions.
find /usr -type f -exec ls -lh {} \;
HTW Enabled:
TLB refill exceptions: 12306
HTW Disabled:
TLB refill exceptions: 17805
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/7336/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Moreover, report hardware page table walker support as 'htw' in the ASE
list of /proc/cpuinfo, if the core implements this feature.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7334/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Long integers which are 4 bytes in MIPS32 can't hold new CPU
options anymore, so the type of the 'options' variable is changed
to unsigned long long which allows 32 more cpu options to be defined
for MIPS32
Also, re-arrange the 'options' struct member to avoid potential 4-byte
alignment gap in the middle of the struct.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7324/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This header defines an exported interface (the register layout used in
core dumps and the GP regset accessible with PTRACE_{GET,SET}REGSET),
therefore belongs in uapi.
Signed-off-by: Alex Smith <alex@alex-smith.me.uk>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7458/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The struct user definition in this file is not used anywhere (the ELF
core dumper does not use that format). Therefore, remove the header and
instead enable the asm-generic user.h which is an empty header to
satisfy a few generic headers which still try to include user.h.
Signed-off-by: Alex Smith <alex@alex-smith.me.uk>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7459/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since the core dumper now uses regsets, the old core dump functions are
now unused. Remove them.
Signed-off-by: Alex Smith <alex@alex-smith.me.uk>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7456/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In uapi/asm/ptrace.h, a user version of pt_regs is defined wrapped in
ifndef __KERNEL__. This structure definition does not match anything
used by any kernel API, in particular it does not match the format used
by PTRACE_{GET,SET}REGS.
Therefore, replace the structure definition with one matching what is
used by PTRACE_{GET,SET}REGS. The format used by these is the same for
both 32-bit and 64-bit.
Also, change the implementation of PTRACE_{GET,SET}REGS to use this new
structure definition. The structure is renamed to user_pt_regs when
__KERNEL__ is defined to avoid conflicts with the kernel's own pt_regs.
Signed-off-by: Alex Smith <alex@alex-smith.me.uk>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7457/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On 32-bit/O32, pt_regs has a padding area at the beginning into which the
syscall arguments passed via the user stack are copied. 4 arguments
totalling 16 bytes are copied to offset 16 bytes into this area, however
the area is only 24 bytes long. This means the last 2 arguments overwrite
pt_regs->regs[{0,1}].
If a syscall function returns an error, handle_sys stores the original
syscall number in pt_regs->regs[0] for syscall restart. signal.c checks
whether regs[0] is non-zero, if it is it will check whether the syscall
return value is one of the ERESTART* codes to see if it must be
restarted.
Should a syscall be made that results in a non-zero value being copied
off the user stack into regs[0], and then returns a positive (non-error)
value that matches one of the ERESTART* error codes, this can be mistaken
for requiring a syscall restart.
While the possibility for this to occur has always existed, it is made
much more likely to occur by commit 46e12c07b3 ("MIPS: O32 / 32-bit:
Always copy 4 stack arguments."), since now every syscall will copy 4
arguments and overwrite regs[0], rather than just those with 7 or 8
arguments.
Since that commit, booting Debian under a 32-bit MIPS kernel almost
always results in a hang early in boot, due to a wait4 syscall returning
a PID that matches one of the ERESTART* codes, which then causes an
incorrect restart of the syscall.
The problem is fixed by increasing the size of the padding area so that
arguments copied off the stack will not overwrite pt_regs->regs[{0,1}].
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.13+
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Tested-by: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7454/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Get rid of the WANT_COMPAT_REG_H test and instead define both the 32-
and 64-bit register offset definitions at the same time with
MIPS{32,64}_ prefixes, then define the existing EF_* names to the
correct definitions for the kernel's bitness.
This patch is a prerequisite of the following bug fix patch.
Signed-off-by: Alex Smith <alex@alex-smith.me.uk>
Cc: <stable@vger.kernel.org> # v3.13+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7451/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
So far BCM47XX can only detect amount of HIGHMEM. It still requires
adding (registering) and well-testing before enabling by default.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7396/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This reverts commit d7a887a73d.
Function add_temporary_entry is needed by bcm47xx to support highmem. We
need to add a temporary entry to check for amount of RAM.
The only change made in this revert was replacing (ENTER|EXIT)_CRITICAL.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/7395/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Catalin reported that GPIOs used by bcm47xx don't match layout of his
WRT54GS V1.0 board. It seems we need to distinguish these 54G* devices.
Reported-by: Catalin Patulea <cat@vv.carleton.ca>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/7112/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since this CONFIG option will be used for both Loongson-3A/3B machines,
and not all Loongson-3 machines are produced by Lemote, we rename
CONFIG_LEMOTE_MACH3A to CONFIG_LOONGSON_MACH3X.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7190/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson-3 has some specific instructions (MMI/SIMD) in coprocessor 2.
COP2 isn't independent because it share COP1 (FPU)'s registers. This
patch enable the COP2 usage so user-space programs can use the MMI/SIMD
instructions. When COP2 exception happens, we enable both COP1 (FPU)
and COP2, only in this way the fp context can be saved and restored
correctly.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7189/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson-3B is a 8-cores processor. In general it looks like there are
two Loongson-3A integrated in one chip: 8 cores are separated into two
groups (two NUMA node), each node has its own local memory.
Of course there are some differences between one Loongson-3B and two
Loongson-3A. E.g., the base addresses of IPI registers of each node are
not the same; Loongson-3A use ChipConfig register to enable/disable
clock, but Loongson-3B use FreqControl register instead.
There are two revision of Loongson-3B, the first revision is called as
Loongson-3B1000, whose frequency is 1GHz and has a PRid 0x6306, the
second revision is called as Loongson-3B1500, whose frequency is 1.5GHz
and has a PRid 0x6307. Both revisions has a bug that clock cannot be
disabled at runtime, but this will be fixed in future.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7188/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Multiple Loongson-3A chips can be interconnected with HT0-bus. This is
a CC-NUMA system that every chip (node) has its own local memory and
cache coherency is maintained by hardware. The 64-bit physical memory
address format is as follows:
0x-0000-YZZZ-ZZZZ-ZZZZ
The high 16 bits should be 0, which means the real physical address
supported by Loongson-3 is 48-bit. The "Y" bits is the base address of
each node, which can be also considered as the node-id. The "Z" bits is
the address offset within a node, which means every node has a 44 bits
address space.
Macros XPHYSADDR and MAX_PHYSMEM_BITS are modified unconditionally,
because many other MIPS CPUs have also extended their address spaces.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7187/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch is prepared for Multi-chip interconnection. Since each chip
has a ChipConfig register, LOONGSON_CHIPCFG should be an array.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7185/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch is prepared for Loongson's NUMA support, it offer meaningful
sysfs files such as physical_package_id, core_id, core_siblings and
thread_siblings in /sys/devices/system/cpu/cpu?/topology.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Reviewed-by: Andreas Herrmann <andreas.herrmann@caviumnetworks.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7184/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When used in a non-MT kernel, the cpu_vpe_id macro never made use of
its cpuinfo argument. It doesn't actually need to since it is returning
a constant 0. However not using the argument can lead to build failures
if the compiler then notices that a variable used as part of the
argument is unused. Prevent that problem by "using" the argument as far
as the compiler is concerned, whilst still returning 0 as before.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7280/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These symbols will not be defined when CONFIG_MIPS_CPS=n, but although
the CPS_PM_POWER_GATED state will never be used in that case the
compiler doesn't have enough information to figure that out. Add checks
which evaluate to a constant false for CONFIG_MIPS_CPS=n cases in order
to help the compiler out & eliminate the symbol references.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7278/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This fixes:
{standard input}: Assembler messages:
{standard input}:145: Error: opcode not supported on this processor: vr5000 (mips4) `clz $2,$2'
{standard input}:920: Error: opcode not supported on this processor: vr5000 (mips4) `clz $7,$9'
{standard input}:1797: Error: opcode not supported on this processor: vr5000 (mips4) `clz $7,$7'
{standard input}:1851: Error: opcode not supported on this processor: vr5000 (mips4) `clz $7,$7'
{standard input}:2831: Error: opcode not supported on this processor: vr5000 (mips4) `clz $7,$7'
{standard input}:4209: Error: opcode not supported on this processor: vr5000 (mips4) `clz $7,$7'
{standard input}:4329: Error: opcode not supported on this processor: vr5000 (mips4) `clz $2,$2'
make[2]: *** [arch/mips/mm/tlbex.o] Error 1
which triggered due to a regression causing the file to be built with
`-march=r5000' rather than `-march=sb1', fixed separately. Nevertheless
the error should not happen, the other uses of CLZ are appropriately
guarded. This change copies the arrangement from one of those other
places.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7222/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The SMP capable irq controllers have two interrupt output pins which are
controlled through separate registers, so make the variables arrays.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Gregory Fong <gregory.0xf0@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7318/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the same pattern as with get_*_cpu_type() to allow the compiler
to remove code for non enabled SoC types.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7273/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All three SoCs have in common they have a BMIPS32/BMIPS3300 CPU, so
we can replace this as no SoC with BMIPS4350 support enabled.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7272/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With the clock framework in place, remove unused functions and bits,
and drop the CLK_IGNORE_UNUSED flag, which is now unneeded.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7473/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the clock framework to get the rate of the peripheral clock.
Remove the now obsolete get_uart_baud_base function.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7468/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch introduces common clock framework integration for all
configurable on-chip clocks on Alchemy chips:
- 2 or 3 PLLs which generate integer multiples of the root rate 12MHz,
- 6 dividers which take one of the 3 PLLs as input and divide their
rate by either multiples of 2 or 1 (Au1300).
- another bank of up to 6 muxes which take either one of the 6
above dividers or one of the PLLs directly and divide their rate
further by 1, 2, 3 or 4.
- a few other sources which are used by onchip peripherals and are
informational.
This implementation will take the clock tree as it was set up
by boot firmware: all in-kernel boards should continue to work
without having to set up the clock tree in board code.
CLK_IGNORE_DISABLED will be removed once all drivers have been
converted.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7466/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch changes the static memory controller registers to offsets
from base, prefixes them with AU1000_ to avoid silent failures due to
changed addresses and introduces helpers to access them.
No functional changes, comparing assembly of a few select functions shows
no differences.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7463/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
