In usb_musb_pm_init, we attempt to access an MUSB register
when the i-clock may not be on, or the module is otherwise
not accessible.
We need to either:
- enable the clock before this access, or
- remove this code and move it to the bootloader, or
- enable the clock in the bootloader
If we enable the clock in the bootloader, we might as well
add the workaround in the bootloader itself. This code will
anyway be changed once hwmod is in place, so remove it for now
This allows us to boot the kernel on certain OMAP3 boards with
a bootloader that doesn't enable this clock. Without this, we
will need to upgrade the bootloaders on these boards.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Now that on-chip UARTs each have separate platform_data, the external
UART needs an non-conflicting ID. Since there are 3 on-chip UARTs,
the Zoom2 external UART will be registered after as the fourth.
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Second reason of OMAP4 boot failure on 2.6.31.rc6, the UART
platform data is not getting registered to kernel.
Registration was failing because of clock check failure in
omap_serial_init().
Below patch fix the same.
OMAP4 clock framework patches are still getting discussed on mailing
list so till then we need this.
Signed-off-by: Syed Rafiuddin <rafiuddin.syed@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
After the patch series "[PATCH 00/14] OMAP PM fixes for .31-rc"
merge in 2.6.31-rc5, the kernel crashed during boot on OMAP4430.
This patch fixes it by adding UART4 support and related code.
Without this patch omap_serial_init() would produce " NULL pointer
dereference" and kernel crashes in the bootup on OMAP4430 platform.
Some more info on the merge issue can be found here.
More info- http://lkml.org/lkml/2009/8/20/192
Note: While merging this patch,"IO_ADDRESS" needs to be changed
to "OMAP2_IO_ADDRESS" if the Tony's below series is already merged in.
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg15072.html
Signed-off-by: Syed Rafiuddin <rafiuddin.syed@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
For OMAP3 add MMC1 MMC2 pin mux MMC3 mux is not added as there are
multiple configurations possible, so the muxing is left to be done
in board file.
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Chikkature Rajashekar <madhu.cr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This enables to peek the following data.
$ /debug/iommu/isp# ls
mem nr_tlb_entries regs
mmap pagetable tlb
$ /debug/iommu/isp# head pagetable
L: da: pa:
-----------------------------------------
2: 00001000 8ae4a002
2: 00002000 8e7bb002
2: 00003000 8ae49002
2: 00004000 8ae65002
.....
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add board file for Nokia N800 and N810 devices. Currently only serial ports,
onenand and spi are configured, more to come later.
Tested on Nokia N800.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For some reason usb-tusb6010.c was't compiled, add it to Makefile and
Kconfig. This is prepraration for upcoming n8x0 support.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP tags are deprecrated so drop them.
Drop UART config data which decides which UARTs to enable during boot.
This is no longer necessary since serial core code disables clocks
after inactivity.
Background: with new UART idle code, all on-chip UARTs are idled using
a configurable inactivity timer (default 5 seconds.) After the
inactivity timer, UART clocks are disabled automatically.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Search and replace OMAP_IO_ADDRESS with OMAP1_IO_ADDRESS and OMAP2_IO_ADDRESS,
and convert omap_read/write into a functions instead of a macros.
Also rename OMAP_MPUIO_VBASE to OMAP1_MPUIO_VBASE.
In the long run, most code should use ioremap + __raw_read/write instead.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Do not allow applications to use the full buffer found on
McBSP1,3,4,5. Using the full buffer in threshold mode causes
the McBSP buffer to run dry, which can be observed as channels
are switching (in reality the channels are shifting).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch export through sysfs two properties to configure
maximum threshold for transmission and reception on each
mcbsp instance. Also, it exports two helper functions to
allow mcbsp users to read this values.
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
twl_mmc_cleanup() must free up the regulators that were
allocated by twl_mmc_late_init().
This eliminates the below error when 'omap_hsmmc' module is
repeatedly loaded and unloaded.
"sysfs: cannot create duplicate filename '/devices/platform
/mmci-omap-hs.0/microamps_requested_vmmc'"
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add OTG transceiver to RX51 platform data to prevent kernel NULL pointer
dereference during MUSB initialisation.
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes a wrong setting of resource parameter list in
SMSC911x platform driver data structure for Overo case.
This fixes folowing warning when compiling for Overo board:
warning: initialization from incompatible pointer type
Introduced since commit id:
commit 172ef27544
Author: Steve Sakoman <sakoman@gmail.com>
Date: Mon Feb 2 06:27:49 2009 +0000
ARM: Add SMSC911X support to Overo platform (V2)
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP3EVM uses ISP1504 phy which doesn't require any programming and
thus has to use NOP otg transceiver.
Cleanups being done:
- Remove unwanted code in usb-musb.c file
- Register NOP in OMAP3EVM board file using
usb_nop_xceiv_register().
- Select NOP_USB_XCEIV for OMAP3EVM boards.
- Don't enable TWL4030_USB in omap3_evm_defconfig
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Eino-Ville Talvala <talvala@stanford.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Powerdomain previous state is checked after restoring new states in
suspend. This patch fixes this problem.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Use list_add_tail() when adding discovered UART ports. This is so
traversal using list_for_each_entry() will traverse the list in the
order they were found.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch causes the OMAP uarts to honor the sysfs power/wakeup file
for IOPAD wakeups. Before the OMAP was always woken up from off mode
on a rs232 signal change. This patch also creates a different
platform device for each serial port so that the wakeup properties can
be control per port.
By default, IOPAD wakeups are enabled for each UART. To disable,
# echo disabled > /sys/devices/platform/serial8250.0/power/wakeup
Where serial8250.0 can be replaced by .1, or .2 to control the other
ports.
Original idea and original patch from Russ Dill <russ.dill@gmail.com>
Cc: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
It was possible for an unhandled interrupt to occur if there was incoming
serial traffic during wakeup from suspend. This was caused by the code
in arch-arm/mach-omap2/serial.c keeping interrupt enabled all the time,
but not acking its interrupts. Applies on top of PM branch.
Use the PM begin/end hooks to ensure that the "serial idle" interrupts
are disabled during the suspend path. Also, since begin/end hooks are
now used, use the suspend_state that is passed in the begin hook instead
of the enter hook as per the platform_suspend_ops docs.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Streamline the OMAP4 special IRQ assignments by putting inside
normal init loop instead of having a separate loop.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
By default, prevent functional wakeups from inside a module from
waking up the IVA2. Let DSP Bridge code handle this when loaded.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch creates McBSP support on OMAP4430 development platform. This patch
includes corresponding base address changes for OMAP4.
Signed-off-by: Syed Rafiuddin <rafiuddin.syed@ti.com>
fix the following 'make includecheck' warning:
arch/arm/mach-omap2/mcbsp.c: mach/irqs.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix two bugs in the OMAP3 clock tree pertaining to the SSI, DSS,
USBHOST, and HSOTGUSB devices. These devices are both interconnect
initiators and targets. Without this patch, clk_enable()s on clocks for
these modules can be very high latency (potentially up to ~200
milliseconds) and message such as the following are generated:
Clock usbhost_48m_fck didn't enable in 100000 tries
Two bugs are fixed by this patch. First, OMAP hardware only supports
target CM_IDLEST register bits on ES2+ chips and beyond. ES1 chips
should not wait for these clocks to enable. So, split the appropriate
clocks into ES1 and ES2+ variants, so that kernels running on ES1
devices won't try to wait.
Second, the current heuristic in omap2_clk_dflt_find_idlest() will
fail for these clocks. It assumes that the CM_IDLEST bit to wait upon
is the same as the CM_*CLKEN bit, which is false[1]. Fix by
implementing custom clkops .find_idlest function pointers for the
appropriate clocks that return the correct slave IDLEST bit shift.
This was originally fixed in the linux-omap kernel during 2.6.29 in a
slightly different manner[2][3].
In the medium-term future, all of the module IDLEST code will
eventually be moved to the omap_hwmod code.
Problem reported by Jarkko Nikula <jhnikula@gmail.com>:
http://marc.info/?l=linux-omap&m=124306184903679&w=2
...
1. See for example 34xx TRM Revision P Table 4-213 and 4-217 (for the
DSS case).
2. http://www.spinics.net/lists/linux-omap/msg05512.html et seq.
3. http://lkml.indiana.edu/hypermail/linux/kernel/0901.3/01498.html
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
OMAP2430 I2CHS CM_IDLEST bits are in CM_IDLEST1_CORE, but the CM_*CLKEN bits
are in CM_{I,F}CLKEN2_CORE [1]. Fix by implementing a custom clkops
.find_idlest function to return the correct slave IDLEST register.
...
1. OMAP2430 Multimedia Device Package-on-Package (POP) Silicon Revision 2.1
(Rev. V) Technical Reference Manual, tables 4-99 and 4-105.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some OMAP2/3 hardware modules have CM_IDLEST attributes that are not
handled by the current omap2_wait_clock_ready() code. In preparation
for patches that fix the unusual devices, rename the function
omap2_wait_clock_ready() to omap2_wait_module_ready() and split it
into three parts:
1. A clkops-specific companion clock return function (by default,
omap2_clk_dflt_find_companion())
2. A clkops-specific CM_IDLEST register address and bit shift return
function (by default, omap2_clk_dflt_find_idlest())
3. Code to wait for the CM to indicate that the module is ready
(omap2_cm_wait_idlest())
Clocks can now specify their own custom find_companion() and find_idlest()
functions; used in subsequent patches.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The clock stabilization delay post a M2 divider change is needed
even before a SDRC interface clock re-enable and not only before
jumping back to SDRAM.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch fixes a bug in the CORE dpll scaling sequence which was
errouneously clearing some bits in the SDRC DLLA CTRL register and
hence causing a freeze. The issue was observed only on platforms
which scale CORE dpll to < 83Mhz and hence program the DLL in fixed
delay mode.
Issue reported by Limei Wang <E12499@motorola.com>, with debugging
assistance from Richard Woodruff <r-woodruff2@ti.com> and Girish
Ghongdemath <girishsg@ti.com>.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: Limei Wang <E12499@motorola.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Girish Ghongdemath <girishsg@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
[paul@pwsan.com: updated patch description to include collaboration credits]
Stop setting SDRC_POWER.PWDENA on boot. There is a nasty erratum
(34xx erratum 1.150) that can cause memory corruption if PWDENA is
enabled.
Based originally on a patch from Samu P. Onkalo <samu.p.onkalo@nokia.com>.
Tested on BeagleBoard rev C2.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Samu P. Onkalo <samu.p.onkalo@nokia.com>
This patches ensures the MUX settings are correct for the SDRC
CKE signals to SDRAM. This allows the self-refresh to work when
2 chip-selects are in use.
A warning is thrown away in case the initial muxing is incorrect,
in order to track faulty or old-dated bootloaders.
Note: The CONFIG_OMAP_MUX and CONFIG_OMAP_MUX_WARNINGS options
must be enabled for the mux code to have effect.
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some OMAP3 boards (Beagle Cx, Overo, RX51, Pandora) have 2
SDRAM parts connected to the SDRC.
This patch adds the following:
- add a new argument of type omap_sdrc_params struct*
to omap2_init_common_hw and omap2_sdrc_init for the 2nd CS params
- adapted the OMAP boards files to the new prototype of
omap2_init_common_hw
- add the SDRC 2nd CS registers offsets defines
- adapt the sram sleep code to configure the SDRC for the 2nd CS
Note: If the 2nd param to omap2_init_common_hw is NULL, then the
parameters are not programmed into the SDRC CS1 registers
Tested on 3430 SDP and Beagleboard rev C2 and B5, with
suspend/resume and frequency changes (cpufreq).
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Use async timings when sync timings are not requested.
Also ensure that OneNAND is in async mode when async
timings are used.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap_type() function is added and returns the DEVICETYPE field of
the CONTROL_STATUS register. The result can be used for conditional
code based on whether device is GP (general purpose), EMU or
HS (high security). Also move the type defines so omap1 code
compile does not require ifdefs for sections using these defines.
This code is needed for the following fix to set the SRAM
size correctly for HS omaps. Also at least PM and watchdog
code will need this function.
Signed-off-by: Kevin Hilman <khilman@ti.deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
platform_get_irq may return -ENXIO. but struct omap_mbox mbox_dsp_info.irq
is unsigned, so the error was not noticed.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
twl_mmc23_set_power() has MMC2 twl_mmc_controller hardcoded in it, which
breaks MMC3. Find the right controller to use instead.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
with while (i++ < MAX_CLOCK_ENABLE_WAIT); i can reach MAX_CLOCK_ENABLE_WAIT + 1
after the loop, so if (i == MAX_CLOCK_ENABLE_WAIT) that's still success.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Correspondence with the TI OMAP hardware team indicates that
SDRC_DLLA_CTRL.FIXEDDELAY should be initialized to 0x0f. This number
was apparently derived from process validation. This is only used
when the SDRC DLL is unlocked (e.g., SDRC clock frequency less than
83MHz).
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Program the SDRC_MR_0 register as well during SDRC clock changes.
This register allows selection of the memory CAS latency. Some SDRAM
chips, such as the Qimonda HYB18M512160AF6, have a lower CAS latency
at lower clock rates.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
When changing the SDRAM clock from 166MHz to 83MHz via the CORE DPLL M2
divider, add a short delay before returning to SDRAM to allow the SDRC
time to stabilize. Without this delay, the system is prone to random
panics upon re-entering SDRAM.
This time delay varies based on MPU frequency. At 500MHz MPU frequency at
room temperature, 64 loops seems to work okay; so add another 32 loops for
environmental and process variation.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On the OMAP3, initialize SDRC timings when the kernel boots. This ensures
that the kernel is running with known, optimized SDRC timings, rather than
whatever was configured by the bootloader.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The original CDP kernel that this code comes from waited for 0x800
loops after switching the CORE DPLL M2 divider. This does not appear
to be necessary.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch adds SMP platform specific parts for local(mpu) timer support
for OMAP4430 platform. Each Cortex-a9 core has it's own local timer in the
MPU domain. These timers are not in wakeup domain.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This patch adds SMP platform files support for OMAP4430SDP. TI's OMAP4430
SOC is based on ARM Cortex-A9 SMP architecture. It's a dual core SOC
with GIC used for interrupt handling and SCU for cache coherency.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This patch updates the Makefile and Kconfig entries for OMAP4. The OMAP4430 SDP
board file supports only minimal set of drivers.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds the support for OMAP4. The platform and machine specific
headers and sources updated for OMAP4430 SDP platform.
OMAP4430 is Texas Instrument's SOC based on ARM Cortex-A9 SMP architecture.
It's a dual core SOC with GIC used for interrupt handling and SCU for cache
coherency.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for keypad, GPIO keys and LEDs. Also enable hardware
debounce feature for GPIO keys.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Setup regulators for MMC1 and MMC2 to get those SD slots
working again.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
CC: David Brownell <david-b@pacbell.net>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Initialize regulators for Beagle and Overo.
Patch is based on earlier patches posted to linux-omap mailing
list.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Decouple the HSMMC glue from the twl4030 as the only
regulator provider, using the regulator framework instead.
This makes the glue's "mmc-twl4030" name become a complete
misnomer ... this code could probably all migrate into the
HSMMC driver now.
Tested on 3430SDP (SD and low-voltage MMC) and Beagle (SD),
plus some other boards (including Overo) after they were
converted to set up MMC regulators properly.
Eventually all boards should just associate a regulator with
each MMC controller they use. In some cases (Overo MMC2 and
Pandora MMC3, at least) that would be a fixed-voltage regulator
with no real software control. As a temporary hack (pending
regulator-next updates to make the "fixed.c" regulator become
usable) there's a new ocr_mask field for those boards.
Patch updated with a fix for disabling vcc_aux by
Adrian Hunter <adrian.hunter@nokia.com>
Cc: Pierre Ossman <drzeus-list@drzeus.cx>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on an earlier patches by Stanley.Miao <stanley.miao@windriver.com>
and Nishant Kamat <nskamat@ti.com>.
Note that at the ads7846 support still needs support for vaux_control
for the touchscreen to work.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on an earlier patch by Stanley.Miao <stanley.miao@windriver.com>
with board-*.c changes split to avoid conflicts with other device updates.
Cc: linux-fbdev-devel@lists.sourceforge.net
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add timing data for the Qimonda HYB18M512160AF-6 SDRAM chip, used on
the OMAP3430SDP boards.
Thanks to Rajendra Nayak <rnayak@ti.com> for his help identifying
the chip used on 3430SDP.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add timing data for the Micron MT46H32M32LF-6 SDRAM chip, used on the
OMAP3 Beagle and EVM boards. Original timing data is from the Micron
datasheet PDF downloaded from:
http://download.micron.com/pdf/datasheets/dram/mobile/1gb_ddr_mobile_sdram_t48m.pdf
Thanks to Rajendra Nayak <rnayak@ti.com> for his help identifying
the chips used on Beagle & OMAP3EVM.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move platform_device_register() for serial device to
omap_serial_init()
There is no need to have arch_initcall() dependency in serial
as already board files call the function omap_serial_init()
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on an earlier patch by Hunyue Yau <hyau@mvista.com> with
board-*.c changes split to avoid conflicts with other device updates.
Cc: linux-fbdev-devel@lists.sourceforge.net
Signed-off-by: Hunyue Yau <hyau@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert the board-rx51 smc91x code to be generic and make
the boards to use it. This allows future recalculation of the
timings when the source clock gets scaled.
Also correct the rx51 interrupt to be IORESOURCE_IRQ_HIGHLEVEL.
Thanks to Paul Walmsley <paul@pwsan.com> for better GPMC timing
calculations.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add generic onenand support when connected to GPMC and make the
boards to use it.
The patch has been modified to make it more generic to support all
the boards with GPMC. The patch also remove unused prototype for
omap2_onenand_rephase(void).
Note that board-apollon.c is currently using the MTD_ONENAND_GENERIC
and setting the GPMC timings in the bootloader. Setting the GPMC
timings in the bootloader will not allow supporting frequency
scaling for the onenand source clock.
Signed-off-by: Tony Lindgren <tony@atomide.com>
By default, prevent functional wakeups from inside a module from
waking up the IVA2. Let DSP Bridge code handle this when loaded.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add D2D clocks (modem_fck, sad2d_ick, mad2d_ick) to clock framework
and ensure that auto-idle bits are set for these clocks during PRCM
init.
Also add omap3_d2d_idle() function called durint PRCM setup which
ensures D2D pins are MUX'd correctly to enable retention for
standalone (no-modem) devices.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch makes it possible to change uart sleep timeout. New sysfs
entry is added (/sys/devices/platform/serial8250.<uart>/sleep_timeout)
Writing zero will disable the timeout feature and prevent UART clocks
from being disabled.
Also default timeout is increased to 5 second to make serial console
more usable.
Original patch was written by Tero Kristo.
Cc: Tero Kristo <Tero.Kristo@nokia.com>
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch allows the UART clocks to be disabled when the OMAP UARTs
are inactive, thus permitting the chip to hit retention in idle.
After the expiration of an activity timer, each UART is allowed to
disable its clocks so the system can enter retention. The activity
timer is (re)activated on any UART interrupt, UART wake event or any
IO pad wakeup. The actual disable of the UART clocks is done in the
'prepare_idle' hook called from the OMAP idle loop.
While the activity timer is active, the smart-idle mode of the UART is
also disabled. This is due to a "feature" of the UART module that
after a UART wakeup, the smart-idle mode may be entered before the
UART has communicated the interrupt, or upon TX, an idle mode may be
entered before the TX FIFOs are emptied.
Upon suspend, the 'prepare_suspend' hook cancels any pending activity
timers and allows the clocks to be disabled immediately.
In addition, upon disabling clocks the UART state is saved in case
of an off-mode transition while clocks are off.
Special thanks to Tero Kristo for the initial ideas and first versions
of UART idle support, and to Jouni Hogander for extra testing and
bugfixes.
Tested on OMAP3 (Beagle, RX51, SDP, EVM) and OMAP2 (n810)
Cc: Tero Kristo <tero.kristo@nokia.com>
Cc: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add common omap2/3 function to check wether there is irq pending.
Switch to use it in omap2 pm code instead of its own.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch is to sync the core linux-omap PM code with mainline. This
code has evolved and been used for a while the linux-omap tree, but
the attempt here is to finally get this into mainline.
Following this will be a series of patches from the 'PM branch' of the
linux-omap tree to add full PM hardware support from the linux-omap
tree.
Much of this PM core code was written by Jouni Hogander with
significant contributions from Paul Walmsley as well as many others
from Nokia, Texas Instruments and linux-omap community.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This reverts commit 5461af5af5.
Adding a disable hook to the irq_chip is not the way to fix the
problem being addressed by this patch. Instead, we need to fix
support for [enable|disable]_irq_wake().
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
We don't necessarily want to compile in irq.o and sdrc.o for omap4.
Also, clock and prcm may not be implemented initially.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove OMAP_PRM_REGADDR and use processor specific defines instead.
Also fold in a patch from Kevin Hilman to add _OFFSET #defines
for the PRCM registers to be used with the prm_[read|write]_* macros.
These are used extensively in the forthcoming OMAP PM support.
Also remove now unused OMAP2_PRM_BASE.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use processor specific defines instead.
As an extra bonus, this patch fixes the problem of CONFIG_DEBUG_SPINLOCK
calling sched_clock before we have things initialized:
http://patchwork.kernel.org/patch/15810/
Signed-off-by: Tony Lindgren <tony@atomide.com>
We don't necessarily want to compile in irq.o and sdrc.o for omap4.
Also, clock and prcm may not be implemented initially.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove OMAP_PRM_REGADDR and use processor specific defines instead.
Also fold in a patch from Kevin Hilman to add _OFFSET #defines
for the PRCM registers to be used with the prm_[read|write]_* macros.
These are used extensively in the forthcoming OMAP PM support.
Also remove now unused OMAP2_PRM_BASE.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use processor specific defines instead.
As an extra bonus, this patch fixes the problem of CONFIG_DEBUG_SPINLOCK
calling sched_clock before we have things initialized:
http://patchwork.kernel.org/patch/15810/
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently "tidspbridge" driver uses its own mmu implementation and
will migrate to use this "omap iommu" eventually. This config is
provided to make this migration happen smoothly.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
This makes the framebuffer work on omap3.
Also fix the clk_get usage for checkpatch.pl
"ERROR: do not use assignment in if condition".
Cc: Imre Deak <imre.deak@nokia.com>
Cc: linux-fbdev-devel@lists.sourceforge.net
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP3430ES2_SAVEANDRESTORE_SHIFT macro is used
by powerdomain code in
"1 << OMAP3430ES2_SAVEANDRESTORE_SHIFT" manner, but
the definition was also (1 << 4), meaning we actually
modified bit 16. So the definition needs to be 4.
This fixes also a cold reset HW bug in OMAP3430 ES3.x
where some of the efuse bits are not isolated during
wake-up from off mode. This can cause randomish
cold resets with off mode. Enabling the USBTLL hardware
SAVEANDRESTORE causes the core power up assert to be
delayed in a way that we will not get faulty values
when boot ROM is reading the unisolated registers.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rename clk_init_one() to clk_preinit() to distinguish its function
from clk_init() and the individual struct clk init functions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On our system we see the following messages:
Disabling unused clock "gpt2_ick"
Disabling unused clock "gpt3_ick"
Disabling unused clock "gpt4_ick"
Disabling unused clock "gpt5_ick"
...
The messages have KERN_INFO level and if you have serial
console, they normally go there. I do not think it is good
idea to print that much stuff there. Moreover, messages
are not properly prefixed and for mortals it is not
immeadietly clear where they come from.
Let's give them debugging level instead.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
[paul@pwsan.com: trimmed debugging output in patch description]
The CORE DPLL M2 frequency change code should use pr_debug(), not
pr_info(), for its debug messages. Same with
omap2_clksel_round_rate_div(). While here, convert a few printk(KERN_ERR ..
into pr_err().
Signed-off-by: Paul Walmsley <paul@pwsan.com>
According to the 34xx TRM Rev. K section 11.2.4.4.11.1 "Purpose of the
DLL/CDL Module," the SDRC delay-locked-loop can be locked at any SDRC
clock frequency from 83MHz to 166MHz. CDP code unconditionally
unlocked the DLL whenever shifting to a lower SDRC speed, but this
seems unnecessary and error-prone, as the DLL is no longer able to
compensate for process, voltage, and temperature variations. Instead,
only unlock the DLL when the SDRC clock rate would be less than 83MHz.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Renumber registers in omap3_sram_configure_core_dpll() assembly code to
make space for additional parameters.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Initialize SDRC_POWER to a known-good setting when the kernel boots.
Necessary since some bootloaders don't initialize SDRC_POWER properly.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Clear the SDRC_POWER.PWRENA bit before putting the SDRAM into self-refresh
mode. This prevents the SDRC from attempting to power off the SDRAM,
which can cause the system to hang.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add more barriers in the SRAM CORE DPLL M2 divider change code.
- Add a DSB SY after the function's entry point to flush all cached
and buffered writes and wait for the interconnect to claim that they
have completed[1]. The idea here is to force all delayed write
traffic going to the SDRAM to at least post to the L3 interconnect
before continuing. If these writes are allowed to occur after the
SDRC is idled, the writes will not be acknowledged and the ARM will
stall.
Note that in this case, it does not matter if the writes actually
complete to the SDRAM - it is only necessary for the writes to leave
the ARM itself. If the writes are posted by the interconnect when
the SDRC goes into idle, the writes will be delayed until the SDRC
returns from idle[2]. If the SDRC is in the middle of a write when
it is requested to enter idle, the SDRC will not acknowledge the
idle request until the writes complete to the SDRAM.[3]
The old-style DMB in sdram_in_selfrefresh is now superfluous, so,
remove it.
- Add an ISB before the function's exit point to prevent the ARM from
speculatively executing into SDRAM before the SDRAM is enabled[4].
...
1. ARMv7 ARM (DDI 0406A) A3-47, A3-48.
2. Private communication with Richard Woodruff <r-woodruff2@ti.com>.
3. Private communication with Richard Woodruff <r-woodruff2@ti.com>.
4. ARMv7 ARM (DDI 0406A) A3-48.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
With the clkdev, musb_core.c needs to register clock with name "ick".
Once all the platforms using the musb driver have been converted
to use clockdev, the clock name does not need to be passed
from the low-level init code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
SPI driver will do unhandled fault on OMAP2420 if trying to probe
non-existing SPI busses. Register those additional busses runtime only
for cpus having them.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix "tusb6010 init error 5, -19" and compilation warning from function
tusb6010_platform_retime "warning: 'sysclk_ps' is used uninitialized in this
function".
I suppose commit c094ba34b8f780885d029ce3c2715a194b780e5d was meant to test
for zero fclk_ps instead of sysclk_ps.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Roel Kluin <roel.kluin@gmail.com>
Tested-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO de-bounce clocks don't have any impact on the module idle state, so
the clock code should not wait for the module to enable after the de-bounce
clocks are enabled.
Problem found by Kevin Hilman <khilman@deeprootsystems.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The structure 'arch_mmu' accommodates the difference between omap1 and
omap2/3.
This patch provides omap2/3 specific functions
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Add a function omap2_gp_clockevent_set_gptimer() for board-*.c files
to use in .init_irq functions to configure the system tick GPTIMER.
Practical choices at this point are GPTIMER1 or GPTIMER12. Both of
these timers are in the WKUP powerdomain, and so are unaffected by
chip power management. GPTIMER1 can use sys_clk as a source, for
applications where a high-resolution timer is more important than
power management. GPTIMER12 has the special property that it has the
secure 32kHz oscillator as its source clock, which may be less prone
to glitches than the off-chip 32kHz oscillator. But on HS devices, it
may not be available for Linux use.
It appears that most boards are fine with GPTIMER1, but BeagleBoard
should use GPTIMER12 when using a 32KiHz timer source, due to hardware bugs
in revisions B4 and below. Modify board-omap3beagle.c to use GPTIMER12.
This patch originally used a Kbuild config option to select the GPTIMER,
but was changed to allow this to be specified in board-*.c files, per
Tony's request.
Kalle Vallo <kalle.valo@nokia.com> found a bug in an earlier version of
this patch - thanks Kalle.
Tested on Beagle rev B4 ES2.1, with and without CONFIG_OMAP_32K_TIMER, and
3430SDP.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: Kalle Valo <kalle.valo@nokia.com>
This patch avoids waiting for the camera module to become ready,
since it doesn't have IDLEST bit.
Based on a earlier hack done by Paul Walmsley on Sep 9 2008 on
linux-omap tree.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 8ad8ff6548 breaks the OMAP2xxx
cpu_mask code, which causes OMAP2xxx to panic on boot. Fix by
removing the cpu_mask auto variable and by changing CK_242X
and CK_243X to use RATE_IN_242X/RATE_IN_243X.
Resolves
<1>Unable to handle kernel NULL pointer dereference at virtual address 0000000c
<1>pgd = c0004000
<1>[0000000c] *pgd=00000000
Internal error: Oops: 5 [#1]
Modules linked in:
CPU: 0 Not tainted (2.6.29-omap1 #32)
PC is at omap2_clk_set_parent+0x104/0x120
LR is at omap2_clk_set_parent+0x28/0x120
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
SPURIOUSIRQ is contained in bits 31:7 of INTC_SIR, so
INTC_SIR must be right shifted by 7, not 6.
No change in logic, only changes for better readability.
Refer to register definition of INTCPS_SIR_IRQ in OMAP3 Manual.
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In linus' git tree the functions can be found at:
vi arch/arm/mach-omap2/usb-tusb6010.c +200 - tusb6010_platform_retime()
vi arch/arm/mach-omap2/gpmc.c +94 - gpmc_get_fclk_period()
vi arch/arm/mach-omap2/usb-tusb6010.c +53 - tusb_set_async_mode()
vi arch/arm/mach-omap2/usb-tusb6010.c +111 - tusb_set_sync_mode()
is -ENODEV appropriate when sysclk_ps == 0?
This was found by code analysis, please review.
------------------------------>8-------------8<---------------------------------
gpmc_get_fclk_period() may return 0 when gpmc_l3_clk is not enabled. This is
not checked in tusb6010_platform_retime() nor in tusb_set_async_mode() it
seems. In tusb_set_sync_mode() this may result in a division by zero.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is no anymore legacy driver for OMAP24XX Enhanced Audio Controller
in linux-omap and it was newer in mainline so cleanup these unneeded
defines and initialization code.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This should be done with GPIO calls. Patches against the
mainline tree welcome to add the necessary working functionality
back.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 3f0a820c4c breaks OMAP2xxx boot
during initial propagate_rate() on osc_ck and sys_ck. Fix by
pre-initializing all struct clks before running any other clock init
code. Incorporates review comments from Russell King
<rmk+kernel@arm.linux.org.uk>.
Resolves
<1>Unable to handle kernel NULL pointer dereference at virtual address 00000000
<1>pgd = c0004000
<1>[00000000] *pgd=00000000
Internal error: Oops: 5 [#1]
Modules linked in:
CPU: 0 Not tainted (2.6.29-omap1 #37)
PC is at propagate_rate+0x10/0x60
LR is at omap2_clk_init+0x30/0x218
...
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Pass clocksource pointer to the read() callback for clocksources. This
allows us to share the callback between multiple instances.
[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the second go through of the old DMA_nBIT_MASK macro,and there're not
so many of them left,so I put them into one patch.I hope this is the last round.
After this the definition of the old DMA_nBIT_MASK macro could be removed.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Greg KH <greg@kroah.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Gumstix will soon be shipping a variant of their Summit board that
includes an SMSC LAN9221 ethernet interface. This patch provides
support via the smsc911x driver when enabled in kernel config.
The Overo defconfig is not updated since the LAN9221 is an option
not present on all systems.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Steve Glendinning <steve.glendinning@smsc.com>
from 2.6.29, smc911x isn't maintained anymore. A new driver, smsc911x,
will replace it. so convert omap_ldp to use smsc911x driver.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
This fixes a compile error caused by a mismerge while rebasing the patch:
linux-2.6/arch/arm/mach-omap2/board-rx51-peripherals.c:354:
undefined reference to `twl4030_mmc_init'
Looks like I need to also update my build scripts, just grepping for error:
in the logs is not obviously enough..
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adds board files and related headers for Nokia RX-51
Internet Tablet.
This patch has been updated with some clean-up patches
posted earlier to linux-omap list.
Signed-off-by: Lauri Leukkunen <lauri.leukkunen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for 3430 SDP.
Various updates have been merged into this patch from
the linux-omap list.
Patch updated to initialize regulators by David Brownell
<dbrownell@users.sourceforge.net>.
Signed-off-by: Syed Mohammed Khasim <khasim@ti.com>
David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
An upcoming Overo expansion board includes an ADS7846 touchscreen controller.
This patch adds support via the ads7846 driver when enabled in the
kernel config.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Create a generic board-file for initializing usb
on omap2430 and omap3 boards.
Patch modified by Tony to build the module based on
CONFIG_USB_MUSB_SOC. Also merged in a patch adding
the nop xceiv from Ajay Kumar Gupta <ajay.gupta@ti.com>.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Allow a cover switch to be used to cause a rescan of the
MMC slot.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Resolve longstanding issue noted by Adrian Hunter: confusion
between settting VSEL=0 (which is 1.8V on MMC1) and poweroff.
Also, leave VSEL alone if we're just powering the regulator off.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Device connected to MMC3 is assumed to be self-powered, so
set_power() function is empty. It can't be omited because
host driver requires it.
Array size for hsmmc[] is specified to allocate to allocate
an instance for the third MMC controller.
Also fix a leak which happens if invalid controller id
is passed.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When setting up HSMMC devices, pass the device nodes back so
board code can linking them to their power supply regulators.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Correct twl4030 MMC power switching: fix voltage ranges reported
for each slot, and handle them fully.
Lies corrected:
- MMC-1 doesn't support the 2.6-2.7 Volt range
- MMC-2 can't normally support anything except 1.8V
Omissions corrected
- MMC-1 *does* handle the 2.8-2.9 Volt range
- MMC-2 can handle 2.5-3.2 Volt cards, given a transceiver
Add transciever support for MMC-2; enable it for Overo and Pandora.
(Depends on something else to have set up pinmuxing for control
signals instead of as MMC2_DAT4..7 pins.)
Also shrink twl4030_hsmmc_info a smidgeon ... padding is all gone.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add 1 to buffer length for null terminator and use snprintf.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds several new GPIO pins and updates
the pin naming comments.
The patch is based on earlier patches on linux-omap
list by Manikandan Pillai <mani.pillai@ti.com>,
Vaibhav Hiremath <hvaibhav@ti.com> and
David Brownell <dbrownell@users.sourceforge.net>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is no CONFIG_I2C2_OMAP_BEAGLE in mainline and it is under
removal in linux-omap also so remove this dead code now.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP_TAGS should vanish soon since they're not generic arm tags.
Most of them can be converted to a platform_data or parsed
from a command line like e.g. serial tag.
For OMAP_TAG_USB we just let boards call omap_usb_init()
passing a pointer to omap_usb_config.
Patch updated by Tony for mainline, basically make
n770 and h4 compile. Also folded in a fix for OSK
by David Brownell <dbrownell@users.sourceforge.net>.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the defines to the associated board file and remove
the now unnecessary header file. Also rename
OMAP34XX_ETHR_START to LDP_ETHR_START.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the defines to the associated board file and remove
the now unnecessary header file. Also rename
OMAP24XX_ETHR_GPIO_IRQ to H4_ETHR_GPIO_IRQ.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the defines to the associated board file and remove
the now unnecessary header file. Also rename
SDP2430_ETHR_GPIO_IRQ to SDP2430_ETHR_GPIO_IRQ.
Signed-off-by: Tony Lindgren <tony@atomide.com>
* master.kernel.org:/home/rmk/linux-2.6-arm: (23 commits)
[ARM] Fix virtual to physical translation macro corner cases
[ARM] update mach-types
[ARM] 5421/1: ftrace: fix crash due to tracing of __naked functions
MX1 fix include
[ARM] 5419/1: ep93xx: fix build warnings about struct i2c_board_info
[ARM] 5418/1: restore lr before leaving mcount
ARM: OMAP: board-omap3beagle: set i2c-3 to 100kHz
ARM: OMAP: Allow I2C bus driver to be compiled as a module
ARM: OMAP: sched_clock() corrected
ARM: OMAP: Fix compile error if pm.h is included
[ARM] orion5x: pass dram mbus data to xor driver
[ARM] S3C64XX: Fix s3c64xx_setrate_clksrc
[ARM] S3C64XX: sparse warnings in arch/arm/plat-s3c64xx/irq.c
[ARM] S3C64XX: sparse warnings in arch/arm/plat-s3c64xx/s3c6400-clock.c
[ARM] S3C64XX: Fix USB host clock mux list
[ARM] S3C64XX: Fix name of USB host clock.
[ARM] S3C64XX: Rename IRQ_UHOST to IRQ_USBH
[ARM] S3C64XX: Do gpiolib configuration earlier
[ARM] S3C64XX: Staticise s3c64xx_init_irq_eint()
[ARM] SMDK6410: Declare iodesc table static
...
Changing it do 100kHz is needed to make more devices works properly. Controlling the
TI DLP Pico projector[1] doesn't work properly at 400kHz, 100kHz and lower work fine.
EDID readout is unaffected by this change.
[1] http://focus.ti.com/dlpdmd/docs/dlpdiscovery.tsp?sectionId=60&tabId=2234
Signed-off-by: Koen Kooi <koen@beagleboard.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Richard Woodruff writes:
| The historic usage of this has been against single use leaf clocks
| (1st instance of gptimer). When it was used it did:
| clk_get()
| clk_set_parent()
| clk_enable()
|
| This usage was ok for that. Use on a disabled clock is needed.
|
| If there are multiple users on the clock or it is enabled there are
| problems.
|
| The call can still be unfriendly if 2 different drivers are using the
| clock with their own clock get/enable. It might be the function should
| return an error if usecount != 0 to stop surprises. It is all around
| better if the parenting is done when the clock is off.
This is a good reason to ensure that the clock is not enabled when
clk_set_parent() is called.
Acked-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The following patch enables SMC911x support to work on the OMAP LDP
board. Although the SMC911x driver will eventually be obsoleted, the
smsc911x patches are rather invasive for the -rc kernels.
Rather than risk destablising smsc911x, this simpler patch is preferred
to allow the network interface to work.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pr_err() for errors rather than pr_debug(). pr_debug() are
compiled away unless -DDEBUG is used.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Richard Woodruff writes that chip errata prevent USBTLL SAR from working
on OMAP3 ES levels before ES3.1:
http://marc.info/?l=linux-arm-kernel&m=123319614808833&w=2
Update the OMAP3 powerdomain structures appropriately.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some OMAP3 chip behaviors change in ES levels after ES2. Modify the
existing omap_chip flags to add options for ES3.0 and ES3.1.
Add a new macro, CHIP_GE_OMAP3430ES2, to cover ES levels from ES2
onwards - a common pattern for OMAP3 features. Update all current
users of the omap_chip macros to use this new macro.
Also add CHIP_GE_OMAP3430ES3_1 to cover the USBTLL SAR errata case
(described and fixed in the following patch)
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This roughly corresponds with OMAP commits: 7d06c48, 3241b19,
88b5d9b, 18a5500, 9c909ac, 5c6497b, 8b1f0bd, 2ac1da8.
For both OMAP2 and OMAP3, we note the reference and bypass clocks in
the DPLL data structure. Whenever we modify the DPLL rate, we first
ensure that both the reference and bypass clocks are enabled. Then,
we decide whether to use the reference and DPLL, or the bypass clock
if the desired rate is identical to the bypass rate, and program the
DPLL appropriately. Finally, we update the clock's parent, and then
disable the unused clocks.
This keeps the parents correctly balanced, and more importantly ensures
that the bypass clock is running whenever we reprogram the DPLL. This
is especially important because the procedure for reprogramming the DPLL
involves switching to the bypass clock.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When changing the parent of a clock, it is necessary to keep the
clock use counts balanced otherwise things the parent state will
get corrupted. Since we already disable and re-enable the clock,
we might as well use the recursive versions instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
_omap2_clksel_get_src_field() was returning the first entry which was
either the default _or_ applicable to the SoC. This is wrong - we
should be returning the first default which is applicable to the SoC.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The error checks for omap2_divisor_to_clksel() and comment disagree with
the actual value returned on error. Fix this to return the correct error
value.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
linux-omap source commit 33d000c99ee393fe2042f93e8422f94976d276ce
introduces a way to "dry run" clock changes before they're committed.
However, this involves putting logic to handle this into each and
every recalc function, and unfortunately due to the caching, led to
some bugs.
Solve both of issues by making the recalc methods always return the
clock rate for the clock, which the caller decides what to do with.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Clock rate change code executes inside a spinlock with hardirqs
disabled. The only code that should be messing around with the
hardirq state should be the plat-omap/clock.c code. In the
omap2_reprogram_dpllcore() case, this probably just wastes cycles, but
in the omap3_core_dpll_m2_set_rate() case, this is a nasty bug.
linux-omap source commit is b9b6208dadb5e0d8b290900a3ffa911673ca97ed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Based on a patch from Paul Walmsley <paul@pwsan.com>:
omap2_clk_enable() should enable a clock's clockdomain before
attempting to enable its parent clock's clockdomain. Similarly, in
the unlikely event that the parent clock enable fails, the clockdomain
should be disabled.
linux-omap source commit is 6d6e285e5a7912b1ea68fadac387304c914aaba8.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Based upon a patch from Paul Walmsley <paul@pwsan.com>:
If _omap2_clk_enable() fails, the clock's usecount must be decremented
by one no matter whether the clock has a parent or not.
but reorganised a bit.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Several parts of the OMAP2/3 clock code use wmb() to try to ensure
that the hardware write completes before continuing. This approach is
problematic: wmb() only ensures that the write leaves the ARM. It
does not ensure that the write actually reaches the endpoint device.
The endpoint device in this case - either the PRM, CM, or SCM - is
three interconnects away from the ARM - and the final interconnect is
low-speed. And the OCP interconnects will post the write, and who
knows how long that will take to complete. So the wmb() is not what
we want. Worse, the wmb() is indiscriminate; it causes the ARM to
flush any other unrelated buffered writes and wait for the local
interconnect to acknowledge them - potentially very expensive.
Fix this by converting the wmb()s into readbacks of the same PRM/CM/SCM
register. Since the PRM/CM/SCM devices use a single OCP thread, this
will cause the MPU to block while waiting for posted writes to that device
to complete.
linux-omap source commit is 260f5487848681b4d8ea7430a709a601bbcb21d1.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Consolidate the commit code for DELAYED_APP clocks into a subroutine,
_omap2xxx_clk_commit(). Also convert the MPU barrier wmb() into an
OCP barrier, since with an MPU barrier, we have no guarantee that the
write actually reached the endpoint device.
linux-omap source commit is 0f5bdb736515801b296125d16937a21ff7b3cfdc.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
clk_disable() previously used an ARM barrier, wmb(), to try to ensure
that the hardware write completed before continuing. There are some
problems with this approach.
The first problem is that wmb() only ensures that the write leaves the
ARM -- not that it actually reaches the endpoint device. In this
case, the endpoint device - either the PRM, CM, or SCM - is three
interconnects away from the ARM, and the final interconnect is
low-speed. And the OCP interconnects will post the write, who knows
how long that will take to complete. So the wmb() is not really what
we want.
Worse, the wmb() is indiscriminate; it will cause the ARM to flush any
other unrelated buffered writes and wait for the local interconnect to
acknowledge them - potentially very expensive.
This first problem could be fixed by doing a readback of the same PRM/CM/SCM
register. Since these devices use a single OCP thread, this will cause the
MPU to wait for the write to complete.
But the primary problem is a conceptual one: clk_disable() should not
need any kind of barrier. clk_enable() needs one since device driver
code must not access a device until its clocks are known to be
enabled. But clk_disable() has no such restriction.
Since blocking the MPU on a PRM/CM/SCM write can be a very
high-latency operation - several hundred MPU cycles - it's worth
avoiding this barrier if possible.
linux-omap source commit is f4aacad2c0ed1055622d5c1e910befece24ef0e2.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Traditionally, we've tracked the parent/child relationships between
clk structures by setting the child's parent member to point at the
upstream clock. As a result, when decending the tree, we have had
to scan all clocks to find the children.
Avoid this wasteful scanning by keeping a list of the clock's children.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This implements the remainder of:
OMAP clock: move rate recalc, propagation code up to plat-omap/clock.c
from Paul Walmsley which is not covered by the previous:
[ARM] omap: move clock propagation into core omap clock code
[ARM] omap: remove unnecessary calls to propagate_rate()
[ARM] omap: move propagate_rate() calls into generic omap clock code
commits.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the standard clk_set_rate() function in omap2_clk_arch_init()
rather than omap2_select_table_rate() -- this will ensure that clock
rates are recalculated and propagated correctly after those operations
are consolidated into clk_set_rate().
linux-omap source commit is 03c03330017eeb445b01957608ff5db49a7151b6.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Current implementation will disable clocks in the order defined in clock34xx.h,
at least DPLL4_M2X2 will hang in certain cases (and prevent retention / off)
if clocks are not disabled in correct order. This patch makes sure the parent
clocks will be active when disabling a clock.
linux-omap source commit is 672680063420ef8c8c4e7271984bb9cc08171d29.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the omap3_core_dpll_m2_set_rate() function to the OMAP3 clock code,
which calls into the SRAM function omap3_sram_configure_core_dpll() to
change the CORE DPLL M2 divider. (SRAM code is necessary since rate changes
on clocks upstream from the SDRC can glitch SDRAM accesses.)
Use this function for the set_rate function pointer in the dpll3_m2_ck
struct clk. With this function in place, PM/OPP code should be able to
alter SDRAM speed via code similar to:
clk_set_rate(&dpll3_m2_ck, target_rate).
linux-omap source commit is 7f8b2b0f4fe52238c67d79dedcd2794dcef4dddd.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For a given SDRAM clock rate, SDRAM chips require memory controllers
to use a specific set of timing minimums and maximums to transfer data
reliably. These parameters can be different for different memory chips
and can also potentially vary by board.
This patch adds the infrastructure for board-*.c files to pass this
timing data to the SDRAM controller init function. The timing data is
specified in an 'omap_sdrc_params' structure, in terms of SDRC
controller register values. An array of these structs, one per SDRC
target clock rate, is passed by the board-*.c file to
omap2_init_common_hw().
This patch does not define the values for different memory chips, nor
does it use the values for anything; those will come in subsequent patches.
linux-omap source commit is bc84ecfc795c2d1c5cda8da4127cf972f488a696.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Separate SDRC code common to OMAP2/3 from mach-omap2/sdrc2xxx.c to
mach-omap2/sdrc.c. Rename the OMAP2xxx-specific functions to use an
'omap2xxx' prefix rather than an 'omap2' prefix, and use "sdrc" in the
function names rather than "memory." Mark several functions
as static that should not be used outside the sdrc2xxx.c file.
linux-omap source commit is bf1612b9d8d29379558500cd5de9ae0367c41fc4.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rename arch/arm/mach-omap2/memory.c to arch/arm/mach-omap2/sdrc2xxx.c, since
it contains exclusively SDRAM-related functions. Most of the functions
are also OMAP2xxx-specific - those which are common will be separated out
in a following patch.
linux-omap source commit is fe212f797e2efef9dc88bcb5db7cf9db3f9f562e.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the contents of the arch/arm/mach-omap2/memory.h file to the
existing mach/sdrc.h file, and remove memory.h. Modify files which
include memory.h to include asm/arch/sdrc.h instead.
linux-omap source commit is e7ae2d89921372fc4b9712a32cc401d645597807.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes a few OMAP2xxx CM_IDLEST bits that were incorrectly
marked as being OMAP2xxx-wide, when they were actually 2420-specific.
Also, originally when the PRCM register macros were defined, bit shift
macros used a "_SHIFT" suffix, and mask macros used none. This became
a source of bugs and confusion, as the mask macros were mistakenly
used for shift values. Gradually, the mask macros have been updated,
piece by piece, to add a "_MASK" suffix on the end to clarify. This
patch applies this change to the CM_IDLEST_* register bits.
The patch also adds a few bits that were missing, mostly from the 3430ES1
to ES2 revisions.
linux-omap source commits are d18eff5b5fa15e170794397a6a94486d1f774f77,
e1f1a5cc24615fb790cc763c96d1c5cfe6296f5b, and part of
9fe6b6cf8d9e0cbb429fd64553a4b3160a9e99e1
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch rolls up several cleanup patches.
1. Some unnecessarily verbose variable names are used in several clock.c
functions; clean these up per CodingStyle.
2. Remove omap2_get_clksel() and just use clk->clksel_reg and
clk->clksel_mask directly.
3. Get rid of void __iomem * usage in omap2_clksel_get_src_field.
Prepend the function name with an underscore to highlight that it is a
static function.
linux-omap source commits are 7fa95e007ea2f3c4d0ecd2779d809756e7775894,
af0ea23f1ee4a5bea3b026e38761b47089f9048a, and
91c0c979b47c44b08f80e4f8d4c990fb158d82c4.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
During _omap3_noncore_dpll_lock(), if a DPLL has no active downstream
clocks and DPLL autoidle is enabled, the DPLL may never lock, since it
will enter autoidle immediately. To resolve this, disable DPLL
autoidle while locking the DPLL, and unconditionally wait for the DPLL
to lock. This fixes some bugs where the kernel would hang when returning
from retention or return the wrong rate for the DPLL.
This patch is a collaboration with Peter de Schrijver
<peter.de-schrijver@nokia.com> and Kevin Hilman
<khilman@deeprootsystems.com>.
linux-omap source commit is 3b7de4be879f1f4f55ae59882a5cbd80f6dcf0f0.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Peter de Schrijver <peter.de-schrijver@nokia.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The DPLL FREQSEL jitter correction bits are set based on a table in
the 34xx TRM, Table 4-38, according to the DPLL's internal clock
frequency "Fint." Several Fint frequency ranges are missing from this
table. Previously, we allowed these Fint frequency ranges to be
selected in the rate rounding code, but did not change the FREQSEL bits.
Correspondence with the OMAP hardware team indicates that Fint values
not in the table should not be used. So, prevent them from being
selected during DPLL rate rounding. This removes warnings and also
can prevent the chip from locking up.
The first pass through the rate rounding code will update the DPLL max
and min dividers appropriately, so later rate rounding passes will run
faster than the first.
Peter de Schrijver <peter.de-schrijver@nokia.com> put up with several
test cycles of this patch - thanks Peter.
linux-omap source commit is f9c1b82f55b60fc39eaa6e7aa1fbe380c0ffe2e9.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Peter de Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The previous DPLL rate rounding algorithm counted the divider (N) down
from the maximum to 1. Since we currently use a broad DPLL rate
tolerance, and lower N values are more power-efficient, we can often
bypass several iterations through the loop by counting N upwards from
1.
Peter de Schrijver <peter.de-schrijver@nokia.com> put up with several
test cycles of this patch - thanks Peter.
linux-omap source commit is 6f6d82bb2f80fa20a841ac3e95a6f44a5a156188.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Peter de Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove some clutter from omap2_dpll_round_rate().
linux-omap source commit is 4625dceb8583c02a6d67ededc9f6a8347b6b8cb7.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert struct dpll_data.idlest_bit field to idlest_mask. Needed since
OMAP2 uses two bits for DPLL IDLEST rather than one.
While here, add the missing idlest_* fields for DPLL3.
linux-omap source commits are 25bab0f176b0a97be18a1b38153f266c3a155784
and b0f7fd17db2aaf8e6e9a2732ae3f4de0874db01c.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
OMAP34xx ES2 TRM Delta G to H states that the divider for DPLL1_FCLK and
DPLL2_FCLK can divide by 4 in addition to dividing by 1 and 2. Encode this
into the OMAP3 clock framework.
linux-omap source commit is 050684c18f2ea0b08fdd5233a0cd3c7f96e00a0e.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix DPLL jitter correction programming. Previously,
omap3_noncore_dpll_program() stored the FREQSEL jitter correction
parameter to the wrong register. This caused jitter correction to be set
incorrectly and also caused the DPLL divider to be programmed incorrectly.
Also, fix DPLL divider programming. An off-by-one error existed in
omap3_noncore_dpll_program(), causing DPLLs to be programmed with a higher
divider than intended.
linux-omap source commit is 5c0ec88a2145cdf2f2c9cc5fae49635c4c2476c7.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Using sdti doesn't keep emu_pwrdm on if hardware supervised pwrdm
transitions are used. This causes sdti stop to work when power
management is initialized and hardware supervised pwrdm control is
enabled. This patch disables hardware supervised pwrdm control for
emu_pwrdm. Now emu_pwrdm is switched off on boot by software when it
is not used.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the clockdomain autodep code to respect omap_chip platform flags.
Resolves "Unable to handle kernel paging request at virtual address
5f75706d" panic during power management initialization on OMAP2.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Enabling clock in a disabled power domain causes the power domain to be
turned on. However, the power transition is not always finished when
clk_enable() returns and this randomly crashes the kernel when an
interrupt happens right after the clk_enable, and the kernel tries to
read the irq status register for that domain.
Why the irq status register is inaccessible, I don't know. Also it
doesn't seem to be related to the module being not powered up, but to
the transition itself.
The same could perhaps happen after clk_disable also, but I have not
witnessed that.
The problem affects at least dss, cam and sgx clocks.
This change waits for the transition to be finished before returning
from omap2_clkdm_clk_enable().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The SGX device on OMAP3 does not support retention, so remove RET from the
list of possible SGX power states. Problem debugged by Richard Woodruff
<r-woodruff2@ti.com>.
Signed-off-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Each DPLL exists in its own powerdomain (cf 34xx TRM figure 4-18) and
clockdomain; so, create powerdomain and clockdomain structures for them.
Mark each DPLL clock as belonging to their respective DPLL clockdomain.
cf. 34xx TRM Table 4-27 (among other references).
linux-omap source commits are acdb615850b9b4f7d1ab68133a16be8c8c0e7419 and
a8798a48f33e9268dcc7f30a4b4a3ce4220fe0c9.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
sys_clkout2 belongs in the core_clkdm (3430 TRM section 4.7.2.2).
It's not clear whether it actually is in the CORE clockdomain, or whether
it is technically in a different clockdomain; but this is closer to
reality than the present configuration.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add clockdomains for the CM and PRM. These will ultimately replace the
"wkup_clkdm", which appears to not actually exist on the hardware.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
struct clockdomain contains a struct powerdomain *pwrdm and const char
*pwrdm_name. The pwrdm_name is only used at initialization to look up
the appropriate pwrdm pointer. Combining these into a union saves
about 100 bytes on 3430SDP. This patch should not cause any change in
kernel function.
Updated to gracefully handle autodeps that contain invalid powerdomains,
per Russell King's review comments.
Boot-tested on BeagleBoard ES2.1.
linux-omap source commit is 718fc6cd4db902aa2242a736cc3feb8744a4c71a.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a CPUfreq frequency-table implementation for OMAP2 by
walking the PRCM rate-table for available entries and adding them to a
CPUfreq table.
CPUfreq can then be used to manage switching between all the available
entries in the PRCM rate table. Either use the CPUfreq sysfs
interface directly, (see Section 3 of Documentation/cpu-freq/user-guide.txt)
or use the cpufrequtils package:
http://www.kernel.org/pub/linux/utils/kernel/cpufreq/cpufrequtils.html
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Updated to try to use cpufreq_table if it exists.
linux-omap source commit is 77ce544fa48deb7a2003f454624e3ca10d37ab87.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Filling the set_rate and round_rate fields of dpll4_m4_ck makes
this clock programmable through clk_set_rate(). This is needed
to give omapfb control over the dss1_alwon_fck rate.
This patch includes a fix from Tomi Valkeinen <tomi.valkeinen@nokia.com>.
linux-omap source commits are e42218d45afbc3e654e289e021e6b80c657b16c2 and
9d211b761b3cdf7736602ecf7e68f8a298c13278.
Signed-off-by: Måns Rullgård <mans@mansr.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add CSI2 clock struct for handling it with clock API when TI PM is disabled.
linux-omap source commit is 8b20f4498928459276bd3366e3381ad595d23432.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The GFX/SGX functional and interface clocks have different masks, for
some unknown reason, so split EN_SGX_SHIFT into one each for fclk and
iclk.
Correct according to the TRM and the far more important 'does this
actually work at all?' metric.
linux-omap source commit is de1121fdb899f762b9e717f44eaf3fae7c00cd3e.
Signed-off-by: Daniel Stone <daniel.stone@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix some bugs in the OMAP3 clock tree pertaining to the 96MHz clocks.
The 96MHz portion of the clock tree should now have reasonable
fidelity to the 34xx TRM Rev I.
One remaining question mark: it's not clear exactly which 96MHz source
clock the USIM uses. This patch sticks with the previous setting, which
seems reasonable.
linux-omap source commit is 15c706e8179ce238c3ba70a25846a36b73bd2359.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove usbhost_sar_fclk from the OMAP3 clock framework. The bit that
the clock was tweaking doesn't actually enable or disable a clock; it
controls whether the hardware will save and restore USBHOST state
when the powerdomain changes state. (That happens to coincidentally
enable a clock for the duration of the operation, hence the earlier
confusion.)
In place of the clock, mark the USBHOST powerdomain as supporting
hardware save-and-restore functionality.
linux-omap source commit is f3ceac86a9d425d101d606d87a5af44afef27179.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a missing OMAP24xx clock, the SSI L4 interface clock,
as "ssi_l4_ick".
linux-omap source commit is ace129d39b3107d330d4cf6934385d13521f2fec.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix sparse & checkpatch warnings in OMAP2/3 PRCM & PM code. This mostly
consists of:
- converting pointer comparisons to integers in form similar to
(ptr == 0) to the standard idiom (!ptr)
- labeling a few non-static private functions as static
- adding prototypes for *_init() functions in the appropriate header
files, and getting rid of the corresponding open-coded extern
prototypes in other C files
- renaming the variable 'sclk' in mach-omap2/clock.c:omap2_get_apll_clkin
to avoid shadowing an earlier declaration
Clean up checkpatch issues. This mostly involves:
- converting some asm/ includes to linux/ includes
- cleaning up some whitespace
- getting rid of braces for conditionals with single following statements
Also take care of a few odds and ends, including:
- getting rid of unlikely() and likely() - none of this code is particularly
fast-path code, so the performance impact seems slim; and some of those
likely() and unlikely() indicators are probably not as accurate as the
ARM's branch predictor
- removing some superfluous casts
linux-omap source commit is 347df59f5d20fdf905afbc26b1328b0e28a8a01b.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add non-CORE DPLL rate set code and M,N programming for OMAP3.
Connect it to OMAP34xx DPLLs 1, 2, 4, 5 via the clock framework.
You may see some warnings on rate sets from the freqsel code. The
table that TI presented in the 3430 TRM Rev F does not cover Fint <
750000, which definitely occurs in practice. However, the lack of this
freqsel case does not appear to impair the DPLL rate change.
linux-omap source commit is 689fe67c6d1ad8f52f7f7b139a3274b79bf3e784.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than introducing a special 'mcbsp_clk' with code behind it in
mach-omap*/mcbsp.c to handle the SoC specifics, arrange for the mcbsp
driver to be like any other driver. mcbsp requests its fck and ick
clocks directly, and the SoC specific code deals with selecting the
correct clock.
There is one oddity to deal with - OMAP1 fiddles with the DSP clocks
and DSP reset, so we move this to the two callback functions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert OMAP MMC driver to match clocks using the device ID and a
connection ID rather than a clock name. This allows us to eliminate
the OMAP1/OMAP2 differences for the function clock.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
propagate_rate() is recursive, so it makes sense to minimise the
amount of stack which is used for each recursion. So, rather than
recursing back into it from the ->recalc functions if RATE_PROPAGATES
is set, do that test at the higher level.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the clock propagation calls for set_parent and set_rate into
the core omap clock code, rather than having these calls scattered
throughout the OMAP1 and OMAP2 implementations.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The original code in omap2_clk_wait_ready() used to check the low 8
bits to determine whether they were within the FCLKEN or ICLKEN
registers. Specifically, the test is satisfied when these offsets
are used:
CM_FCLKEN, CM_FCLKEN1, CM_CLKEN, OMAP24XX_CM_FCLKEN2, CM_ICLKEN,
CM_ICLKEN1, CM_ICLKEN2, CM_ICLKEN3, OMAP24XX_CM_ICLKEN4
OMAP3430_CM_CLKEN_PLL, OMAP3430ES2_CM_CLKEN2
If one of these offsets isn't used, omap2_clk_wait_ready() merely
returns without doing anything. So we should use the non-wait clkops
version instead and eliminate that conditional.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than employing run-time tests in omap2_clk_wait_ready() to
decide whether we need to wait for the clock to become ready, we
can set the .ops appropriately.
This change deals with the OMAP24xx and OMAP34xx conditionals only.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PARENT_CONTROLS_CLOCK just makes enable/disable no-op, and is
functionally an alias for ALWAYS_ENABLED. This can be handled
in the same way, using clkops_null.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
... and use it for clocks which are ALWAYS_ENABLED. These clocks
use a non-NULL enable_reg pointer for other purposes (such as
selecting clock rates.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Collect up all the common enable/disable clock operation functions
into a separate operations structure.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In omap24xx_cpu_suspend assembly routine, the r2 register which holds
the address of the SDRC_POWER reg is set to zero before the value is
written back triggering a fault due to writing to address zero.
It's hard to tell where this change was introduced since this file
has been moved and merged.
While this fix prevents a crash, suspend on my n810 is broken with
current kernels. I never come out of suspend.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
By Ingo Molnar, interrupts are not masked by default.
(refer to 76d2160147)
But if interrupts are not masked, the processor can wake up while in
Suspend-to-RAM state by an external interrupt. For example, if an
OMAP3 board is connected to Host PC by USB and entered to Suspend-to-RAM
state, it wake up automatically by M_IRQ_92. The disable_irq() function
can't disable the interrupt in H/W level, So I modified
arch/arm/mach-omap2/irq.c
Signed-off-by: Kim Kyuwon <chammoru@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When 32 kHz timer is used the min_delta_ns should be initialized so
that it reflects the timer programming cost. A write to the timer
device will be usually posted, but it takes roughly 3 cycles before
it is effective. If the timer is reprogrammed before that, the CPU
will stall until the previous write completes. This was pointed out by
Richard Woodruff.
Since the lower bound for min_delta_ns is 1000, the change is visible
only with tick rates less than 3 MHz.
Also note that the old value is incorrect for 32 kHz also due to
a rounding error, and it can cause the timer queue to hang (due to
clockevent code trying to program the timer with zero ticks).
Signed-off-by: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Reviewed-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The naming accidentally broke while changing the name for the
driver to not to conflict with the other mmc driver.
Signed-off-by: Tony Lindgren <tony@atomide.com>
A spin_lock deadlock will occur when omap_mcbsp_request() is invoked.
omap_mcbsp_request()
\- clk_enable(mcbsp->clk) [takes and holds clockfw_lock]
\- omap2_clk_enable()
\- _omap2_clk_enable()
\- omap_mcbsp_clk_enable()
\- clk_enable(child clock) [tries for clockfw_lock again]
mcbsp_clk is a virtual clock and it comprises several child clocks. when
enable mcbsp_clk in omap_mcbsp_request(), the enable function of mcbsp_clk
will enable its child clocks, then the deadlock occurs.
The solution is to remove the virtual clock and enable these child clocks in
omap_mcbsp_request() directly.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix compile by removing remaining omap specific gpio
calls. Based on earlier patches by Jarkko Nikula.
Also remove old GPIO key code, there is already a patch
to do this with gpio_keys.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
arch/arm/mach-at91/at91cap9.c:337: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91rm9200.c:301: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9260.c:351: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9261.c:287: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9263.c:312: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9rl.c:304: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-h720x/h7202-eval.c:38: error: implicit declaration of function 'IRQ_CHAINED_GPIOB'
arch/arm/mach-ks8695/devices.c:46: error: 'KS8695_IRQ_WAN_RX_STATUS' undeclared here (not in a function)
arch/arm/mach-msm/devices.c:28: error: 'INT_UART1' undeclared here (not in a function)
arch/arm/mach-mx2/devices.c:233: error: 'MXC_GPIO_IRQ_START' undeclared here (not in a function)
arch/arm/mach-mx3/devices.c:128: error: 'MXC_GPIO_IRQ_START' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:140: error: 'INT_730_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:165: error: 'INT_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:200: error: 'INT_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap2/board-apollon.c:286: error: implicit declaration of function 'omap_set_gpio_direction'
arch/arm/mach-omap2/mcbsp.c:154: error: 'INT_24XX_MCBSP1_IRQ_RX' undeclared here (not in a function)
arch/arm/mach-omap2/mcbsp.c:181: error: 'INT_24XX_MCBSP1_IRQ_RX' undeclared here (not in a function)
arch/arm/mach-pxa/e350.c:36: error: 'IRQ_BOARD_START' undeclared here (not in a function)
arch/arm/plat-s3c/dev-i2c0.c:32: error: 'IRQ_IIC' undeclared here (not in a function)
...
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'i2c-next' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c-omap: fix type of irq handler function
i2c-s3c2410: Change IRQ to be plain integer.
i2c-s3c2410: Allow more than one i2c-s3c2410 adapter
i2c-s3c2410: Remove default platform data.
i2c-s3c2410: Use platform data for gpio configuration
i2c-s3c2410: Fixup style problems from checkpatch.pl
i2c-omap: Enable I2C wakeups for 34xx
i2c-omap: reprogram OCP_SYSCONFIG register after reset
i2c-omap: convert 'rev1' flag to generic 'rev' u8
i2c-omap: fix I2C timeouts due to recursive omap_i2c_{un,}idle()
i2c-omap: Clean-up i2c-omap
i2c-omap: Don't compile in OMAP15xx I2C ISR for non-OMAP15xx builds
i2c-omap: Mark init-only functions as __init
i2c-omap: Add support for omap34xx
i2c-omap: FIFO handling support and broken hw workaround for i2c-omap
i2c-omap: Add high-speed support to omap-i2c
i2c-omap: Close suspected race between omap_i2c_idle() and omap_i2c_isr()
i2c-omap: Do not use interruptible wait call in omap_i2c_xfer_msg
Fix up apparently-trivial conflict in drivers/i2c/busses/i2c-s3c2410.c
* 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (66 commits)
x86: export vector_used_by_percpu_irq
x86: use logical apicid in x2apic_cluster's x2apic_cpu_mask_to_apicid_and()
sched: nominate preferred wakeup cpu, fix
x86: fix lguest used_vectors breakage, -v2
x86: fix warning in arch/x86/kernel/io_apic.c
sched: fix warning in kernel/sched.c
sched: move test_sd_parent() to an SMP section of sched.h
sched: add SD_BALANCE_NEWIDLE at MC and CPU level for sched_mc>0
sched: activate active load balancing in new idle cpus
sched: bias task wakeups to preferred semi-idle packages
sched: nominate preferred wakeup cpu
sched: favour lower logical cpu number for sched_mc balance
sched: framework for sched_mc/smt_power_savings=N
sched: convert BALANCE_FOR_xx_POWER to inline functions
x86: use possible_cpus=NUM to extend the possible cpus allowed
x86: fix cpu_mask_to_apicid_and to include cpu_online_mask
x86: update io_apic.c to the new cpumask code
x86: Introduce topology_core_cpumask()/topology_thread_cpumask()
x86: xen: use smp_call_function_many()
x86: use work_on_cpu in x86/kernel/cpu/mcheck/mce_amd_64.c
...
Fixed up trivial conflict in kernel/time/tick-sched.c manually
Impact: change calling convention of existing clock_event APIs
struct clock_event_timer's cpumask field gets changed to take pointer,
as does the ->broadcast function.
Another single-patch change. For safety, we BUG_ON() in
clockevents_register_device() if it's not set.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
The bootloader may leave the MMC in a state which prevents hitting
retention. Even when MMC is not compiled in, each MMC module needs to
be forced into reset.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add low-level initialization for hsmmc controller. Merged into
this patch patch are various improvments and board support by
Grazvydas Ignotas and David Brownell.
Also change wire4 to be wires, as some newer controllers support
8 data lines.
Cc: Pierre Ossman <drzeus-mmc@drzeus.cx>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This will simplify the MMC low-level init, and make it more
flexible to add support for a newer MMC controller in the
following patches.
The patch rearranges platform data and gets rid of slot vs
controller confusion in the old data structures. Also fix
device id numbering in the clock code.
Some code snippets are based on an earlier patch by
Russell King <linux@arm.linux.org.uk>.
Cc: Pierre Ossman <drzeus-mmc@drzeus.cx>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most of the omap1 MMC boards got broken by an earlier patch
138ab9f832. If you look closely,
the MMC init funtions are pretty much just stubs.
Remove broken init code to make room for cleaner MMC init code.
Cc: Pierre Ossman <drzeus-mmc@drzeus.cx>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds some new pin multiplexing options
for McBSP and McSPI from Arun KS. Also add two more
GPIOs from David Brownell.
Also mark omap24xx_cfg_reg() static.
Signed-off-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for basic features: uarts, i2c,
and rtc. Also includes defconfig.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In the case of spurious interrupt, the handler for previous interrupt
handler needs to flush posted writes with a read back of the interrupt
ack register. Warn about handlers that need to flush posted writes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Declare the two 1Kbit EEPROMs included in the H4 board stack.
One is on the CPU card; the other is on the mainboard.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
system_rev is meant for board revision, this patch changes
all relevant instances to use the new omap_rev() function
liberating system_rev to be used with ATAG_REVISION as it
has been designed.
Signed-off-by: Lauri Leukkunen <lauri.leukkunen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
At some point omap2 changed the bits for GET_OMAP_CLASS, which
broke 15xx detection on 730 as noticed by Russell King.
This patch fixes omap2 cpu detection to respect the original
GET_OMAP_CLASS, and simplifies the detection for 34xx.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rename omap2_check_revision to omap24xx_check_revision.
Then next patch will split if further and add omap34xx_check_revision.
Signed-off-by: Tony Lindgren <tony@atomide.com>
More conversion to the standard GPIO interfaces: stop using
omap_set_gpio_direction() entirely, and switch over to the
gpio_direction_output() call.
Note that because gpio_direction_output() includes the initial
value, this change isn't quite transparent.
- For the call sites which defined an initial value either
before or after setting the direction, that value was used.
When that value was previously assigned afterwards, this
could eliminate a brief output glitch ... and possibly
change behavior. In a few cases (LCDs) several values
were assigned together ... those were re-arranged to match
the explicit sequence provided.
- Some call sites didn't define such a value; so I chose an
initial "off/reset" value that seemed to default to "off".
In short, files touched by this patch might notice some small
changes in startup behavior (with trivial fixes).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
More switchover to the cross-platform GPIO interface:
use gpio_direction_input(), not an OMAP-specific call.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch replaces some legacy OMAP GPIO calls with the "new" (not
really, any more!) calls that work on most platforms.
The calls addressed by this patch are the simple ones to get and set
values ... for code that's in mainline, including the implementations
of those calls.
Except for the declarations and definitions of those calls, all of
these changes were performed by a simple SED script. Plus, a few
"if() set() else set()" branches were merged by hand.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch changes gpio "driver" to enable debounce clock for
gpio-bank only when debounce is enabled for some gpio in that bank.
Gpio functional clocks are also renamed in clock tree, gpioX_fck ->
gpioX_dbck.
This patch triggers problem with gpio wake-up and Omap3. Gpios in PER
domain aren't capable to generate wake-up if PER domain is in sleep
state. For this iopad wake-up should be used and needed pad
configuration should be done. Enabling iopad wake-up for gpio pads is
left for bootloader or omap mux configuration in kernel.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Omap2430 has additional support for high-speed I2C.
This patch moves I2C speed parameter (from module) to platform data.
Also added basic High Speed support based on I2C bus speed.
This patch is tested for high speed I2C (with TWL4030 Keypad) and works as
expected.
Also change the 2430 i2chs_fck names to use the standard naming.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix these compiler warnings:
gpmc.c: In function 'gpmc_init':
gpmc.c:432: warning: 'return' with a value, in function returning void
gpmc.c:439: warning: 'return' with a value, in function returning void
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This merges branches irq/genirq, irq/sparseirq-v4, timers/hpet-percpu
and x86/uv.
The sparseirq branch is just preliminary groundwork: no sparse IRQs are
actually implemented by this tree anymore - just the new APIs are added
while keeping the old way intact as well (the new APIs map 1:1 to
irq_desc[]). The 'real' sparse IRQ support will then be a relatively
small patch ontop of this - with a v2.6.29 merge target.
* 'genirq-v28-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (178 commits)
genirq: improve include files
intr_remapping: fix typo
io_apic: make irq_mis_count available on 64-bit too
genirq: fix name space collisions of nr_irqs in arch/*
genirq: fix name space collision of nr_irqs in autoprobe.c
genirq: use iterators for irq_desc loops
proc: fixup irq iterator
genirq: add reverse iterator for irq_desc
x86: move ack_bad_irq() to irq.c
x86: unify show_interrupts() and proc helpers
x86: cleanup show_interrupts
genirq: cleanup the sparseirq modifications
genirq: remove artifacts from sparseirq removal
genirq: revert dynarray
genirq: remove irq_to_desc_alloc
genirq: remove sparse irq code
genirq: use inline function for irq_to_desc
genirq: consolidate nr_irqs and for_each_irq_desc()
x86: remove sparse irq from Kconfig
genirq: define nr_irqs for architectures with GENERIC_HARDIRQS=n
...
Based on David Brownell's patch for tps65010 and previous work by
Felipe Balbi, this patch finishes converting isp1301_omap to a
new-style i2c driver.
There's definitely room for further drivers cleanups, but these are
out of the scope of this patch.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Tony Lindgren <tony@atomide.com>
This adds minimal board support for the OMAP3430 LDP development platform.
Signed-off-by: Nishant Kamat <nskamat@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add minimal Beagle board support. Based on earlier patches
by Syed Mohammed Khasim with some fixes from linux-omap tree.
Signed-off-by: Syed Mohammed Khasim <khasim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add minimal omap3430 support based on earlier patches from
Syed Mohammed Khasim. Also merge in omap34xx SRAM support
from Karthik Dasu and use consistent naming for sram init
functions.
Also do following changes that make 34xx support usable:
- Remove unused sram.c functions for 34xx
- Rename IRQ_SIR_IRQ to INTCPS_SIR_IRQ and define it locally
in entry-macro.S
- Update mach-omap2/io.c to support 2420, 2430, and 34xx
- Also merge in 34xx GPMC changes to add fields wr_access and
wr_data_mux_bus from Adrian Hunter
- Remove memory initialization call omap2_init_memory() until
until more generic memory initialization patches are posted.
It's OK to rely on bootloader initialization until then.
Signed-off-by: Syed Mohammed, Khasim <khasim@ti.com>
Signed-off-by: Karthik Dasu<karthik-dp@ti.com>
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix sparse warnings in mach-omap2/irq.c. Fix by defining
intc_bank_write_reg() and intc_bank_read_reg(), and convert INTC module
register access to use them rather than __raw_{read,write}l.
Also clear up some checkpatch warnings involving includes from asm/
rather than linux/.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on Chandra's earlier patches in linux-omap tree.
Signed-off-by: Chandra Shekhar <x0044955@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on Chandra's earlier patches in linux-omap tree.
Note that omap1_mcbsp_check and omap2_mcbsp_check are no longer
needed as there's now omap_mcbsp_check_valid_id() defined.
Also some functions can now be marked __init.
Signed-off-by: Chandra Shekhar <x0044955@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Misc updates from linux-omap tree, mostly to update common
device initialization and add missing defines from linux-omap
tree. Also some changes to make room for adding 34xx in
following patches.
Note that the I2C resources are now set up in
arch/arm/plat-omap/i2c.c helper, and can be removed
from devices.c.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix sparse, checkpatch warnings fro GPMC code.
Also change to use ioremap, and add missing function prototypes
to gpmc.h.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds pinmux support for OMAP3. Incorporated review comments
from Tony to make mux_value as bit mask. Tested on 3430SDP.
Also merge in adding of I2C pins from Jarkko Nikula.
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some register offsets are different for 242x and 243x. This
will allow compiling sleep code for both chips into the same
kernel. Pass the addresses for SDRC_DDLA_CTRL and SDRC_POWER to the
omap24xx_cpu_suspend instead of loading the values since the only.
Also fix a bug to call omap2_sram_suspend with the value of SDRC_DLLA_CTRL
instead of the address as that's what omap24xx_cpu_suspend expects to
determine between DDR and SDR. This bug has not been noticed as
the boards seem to have DDR instead of SDR.
Note that some PM patches are still missing. The PM patches will
be added later on once the base files are in sync with linux-omap
tree.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds common function to enable/disable omap2/3 uart
clocks. Enabled uarts are passed by bootloader in atags and clocks for
these enabled uarts are touched.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP1_IO_ADDRESS(), OMAP2_IO_ADDRESS() and IO_ADDRESS() returns cookies
for use with __raw_{read|write}* for accessing registers. Therefore,
these macros should return (void __iomem *) cookies, not integer values.
Doing this improves typechecking, and means we can find those places
where, eg, DMA controllers are incorrectly given virtual addresses to
DMA to, or physical addresses are thrown through a virtual to physical
address translation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
mcbsp is confused as to what takes a physical or virtual address.
Fix the two instances where it gets it wrong.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add asm/cputype.h, moving functions and definitions from asm/system.h
there. Convert all users of 'processor_id' to the more efficient
read_cpuid_id() function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Taken from omap 97b705ad835f1481270c4b67b402d6e37fa8ad15:
ARM: OMAP: Misc compile fixes after syncing with mainline
Also fix 2430 smc91x to use IRQ_LOWLEVEL.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add clkdm_get_pwrdm() to the clockdomain code. It will return a
pointer to the powerdomain struct that the clockdomain is contained
within. Used by the PM code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
OMAP3430ES2+ introduces a new feature: optional powerdomain context
hardware save-and-restore (SAR). Currently, this feature only applies
to USBHOST and USBTLL module context when the USBHOST or CORE
powerdomains enter a low-power sleep state[1]. This feature avoids
re-enumeration of USB devices when the powerdomains return from idle,
which is potentially time-consuming.
This patch adds support for enabling and disabling hardware
save-and-restore to the powerdomain code. Three new functions are
added, pwrdm_enable_hdwr_sar(), pwrdm_disable_hdwr_sar(), and
pwrdm_can_hdwr_sar(). A new struct powerdomain "flags" field is
added, with a PWRDM_HAS_HDWR_SAR flag to indicate powerdomains with
SAR support.
Thanks to Jouni Högander <jouni.hogander@nokia.com> for reviewing an
earlier version of these patches, and Richard Woodruff <r-woodruff2@ti.com>
for clarifying the purpose of these bits.
1. For the USBHOST controller module, context loss occurs when the
USBHOST powerdomain enters off-idle. For USBTLL, context loss
occurs either if CORE enters off-idle, or if the CORE logic is
configured to turn off when CORE enters retention-idle (OSWR).
34xx ES2 TRM 4.8.6.1.1, 4.8.6.1.2
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
E.g dss_l3_ick and dss_l4_ick have same gating control. Having own
clock for both of them causes race condition between enable / disable.
This patch combines this kind of clocks and names new clock as <module>_ick.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch integrates the OMAP3 clock tree with the clockdomain code.
This patch:
- marks OMAP34xx clocks with their corresponding clockdomain.
- adds code to convert the clockdomain name to a clockdomain pointer in the
struct clk during clk_register().
- modifies OMAP2 clock usecounting to call into the clockdomain code
when clocks are enabled or disabled.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Associate each OMAP24xx clock in arch/arm/mach-omap2/clock24xx.h
with a clockdomain.
Also move the L4 clock up higher in the file in preparation to
define the SSI L4 iclk.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add clockdomain definitions for OMAP24xx and OMAP34xx chips.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Thie patch adds code to the powerdomain layer to track the
clockdomains associated with each powerdomain.
It also modifies the clockdomain code to register clockdomains
with their corresponding powerdomain when the clockdomain is registered.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch creates an interface to the clockdomain registers in the
PRM/CM modules on OMAP2/3. This interface is intended to be used by
PM code, e.g., pm.c; not by device drivers directly.
The patch also adds clockdomain usecount tracking. This is intended
to be called whenever the first clock in a clockdomain is enabled, or
when the last enabled clock in a clockdomain is disabled. If the
clockdomain is in software-supervised mode, the code will force-wakeup
or force-sleep the clockdomain. If the clockdomain is in
hardware-supervised mode, the first clock enable will add sleep and
wakeup dependencies on a user-selectable set of parent domains (usually
MPU & IVA2), and the disable will remove them.
Each clockdomain will be defined in later patches as static
structures. The clockdomain structures are linked into a list at boot
by clkdm_register(), similar to the OMAP clock code.
The patch adds a Kconfig option, CONFIG_OMAP_DEBUG_CLOCKDOMAIN, which
when enabled will emit verbose debug messages via pr_debug().
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add powerdomains common to both OMAP2 and OMAP3 (WKUP and GFX/SGX).
Modify mach-omap2/io.c to initialize the powerdomain code on boot.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch creates an interface to the powerdomain registers in the
PRM/CM modules on OMAP2/3. This interface is intended to be used by
PM code, e.g., pm.c; not by device drivers directly.
Each powerdomain will be defined in later patches as static
structures. Also defined are dependencies between powerdomains,
used for adding and removing PM_WKDEP and CM_SLEEPDEP bits. The
powerdomain structures are linked into a list at boot by
pwrdm_register(), similar to the OMAP clock code.
The patch adds a Kconfig option, CONFIG_OMAP_DEBUG_POWERDOMAIN, which
when enabled will emit verbose debug messages via pr_debug().
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use platform_data to pass musb configuration-specific
details to musb driver.
This patch will prevent that other platforms selecting
HAVE_CLK and enabling musb won't break tree building.
The other parts of it will come when linux-omap merge
up more omap2/3 board-files.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are 43 includes of asm/mach-types.h by files that don't
reference anything from that file. Remove these unnecessary
includes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
IRQT_* and __IRQT_* were obsoleted long ago by patch [3692/1].
Remove them completely. Sed script for the reference:
s/__IRQT_RISEDGE/IRQ_TYPE_EDGE_RISING/g
s/__IRQT_FALEDGE/IRQ_TYPE_EDGE_FALLING/g
s/__IRQT_LOWLVL/IRQ_TYPE_LEVEL_LOW/g
s/__IRQT_HIGHLVL/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_RISING/IRQ_TYPE_EDGE_RISING/g
s/IRQT_FALLING/IRQ_TYPE_EDGE_FALLING/g
s/IRQT_BOTHEDGE/IRQ_TYPE_EDGE_BOTH/g
s/IRQT_LOW/IRQ_TYPE_LEVEL_LOW/g
s/IRQT_HIGH/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_PROBE/IRQ_TYPE_PROBE/g
s/IRQT_NOEDGE/IRQ_TYPE_NONE/g
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a new rate rounding algorithm for DPLL clocks on the
OMAP2/3 architecture.
For a desired DPLL target rate, there may be several
multiplier/divider (M, N) values which will generate a sufficiently
close rate. Lower N values result in greater power economy. However,
lower N values can cause the difference between the rounded rate and
the target rate ("rate error") to be larger than it would be with a
higher N. This can cause downstream devices to run more slowly than
they otherwise would.
This DPLL rate rounding algorithm:
- attempts to find the lowest possible N (DPLL divider) to reach the
target_rate (since, according to Richard Woodruff <r-woodruff@ti.com>,
lower N values save more power than higher N values).
- allows developers to set an upper bound on the error between the
rounded rate and the desired target rate ("rate tolerance"), so an
appropriate balance between rate fidelity and power savings can be
set. This maximum rate error tolerance is set via
omap2_set_dpll_rate_tolerance().
- never returns a rounded rate higher than the target rate.
The rate rounding algorithm caches the last rounded M, N, and rate
computation to avoid rounding the rate twice for each clk_set_rate()
call. (This patch does not yet implement set_rate for DPLLs; that
follows in a future patch.)
The algorithm trades execution speed for rate accuracy. It will find
the (M, N) set that results in the least rate error, within a
specified rate tolerance. It does this by evaluating each divider
setting - on OMAP3, this involves 128 steps. Another approach to DPLL
rate rounding would be to bail out as soon as a valid rate is found
within the rate tolerance, which would trade rate accuracy for
execution speed. Alternate implementations welcome.
This code is not yet used by the OMAP24XX DPLL clock, since it
is currently defined as a composite clock, fusing the DPLL M,N and the
M2 output divider. This patch also renames the existing OMAP24xx DPLL
programming functions to highlight that they program both the DPLL and
the DPLL's output multiplier.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for DPLL autoidle control to the OMAP3 clock
framework. These functions will be used by the noncore DPLL enable
and disable code - this is because, according to the CDP code, the
DPLL autoidle status must be saved and restored across DPLL
lock/bypass/off transitions.
N.B.: the CORE DPLL (DPLL3) has three autoidle mode options, rather
than just two. This code currently does not support the third option,
low-power bypass autoidle.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a new OMAP chip identification interface, omap_chip_id.
omap_chip_id is a structure which contains one bit for each OMAP2/3
CPU type, and on 3430, ES level. For example, the CHIP_IS_OMAP2420
bit is set in omap_chip at boot on an OMAP2420. On OMAP3430ES2, both
CHIP_IS_OMAP3430 and CHIP_IS_OMAP3430ES2 bits are set.
omap_chip is set in mach-omap2/id.c by _set_omap_chip(). Other
code should use the omap_chip_is() function to test against omap_chip.
Also, clean up id.c by splitting some code out of
omap_check_revision() into its own function, _set_system_rev(); and
converting some debug printk()s into pr_debug().
Second revision.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
New struct omap_globals contains the omap processor specific
module bases. Use omap_globals to set the various base addresses
to make detecting omap chip type simpler.
Also introduce OMAP1_IO_ADDRESS and OMAP2_IO_ADDRESS for future multi-omap
patches.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for mach-omap2 based on current
mcbsp platform driver.
Signed-off-by: Eduardo Valentin <eduardo.valentin@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for mach-omap1 based on current
mcbsp platform driver.
Signed-off-by: Eduardo Valentin <eduardo.valentin@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch optimizes the timer load and start sequence. By combining the
load and start a needless posted wait can be removed from the system timer
execution path.
* Before patch register writes are taking up .078% @ 500MHz during idle.
Address |total |min |max |avr |count|ratio%
old\process\default_idle|7.369s |0.0us|999.902ms|14.477ms|509. |62.661%
ld\Global\cpu_v7_do_idle|4.265s |0.0us|375.786ms|24.374ms|175. |36.270%
(UNKNOWN)|17.503ms|0.us|531.080us|5.119us|3419. |0.148%
r\omap_dm_timer_set_load|8.135ms|0.0us|79.887us|15.065us|540. |0.069% <--
\vmlinux-old\Global\_end|2.023ms|0.0us|4.000us|0.560us|3613. |0.017%
-old\Global\__raw_readsw|1.962ms|0.0us|108.610us|9.167us|214. |0.016%
old\smc91x\smc_interrupt|1.353ms|0.0us|10.212us|2.348us|576. |0.011%
s/namei\__link_path_walk|1.161ms|0.0us|4.310us|0.762us| 1524. |0.009%
\omap_dm_timer_write_reg|1.085ms|0.0us|126.150us|2.153us|504. |0.009% <--
* After patch timer functions do not show up in top listings for long captures.
Signed-off-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
dyntick is superseded by the clocksource/clockevent infrastructure,
using the NO_HZ configuration option. No one implements dyntick on
ARM anymore, so it's pointless keeping it around. Remove dyntick
support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fixed comments on global PRM register usage.
Signed-off-by: Kalle Jokiniemi <ext-kalle.jokiniemi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch removes following message on dpll5_m2_ck enable and
disable:
clock.c: Enable for dpll5_m2_ck without enable code
clock: clk_disable called on independent clock dpll5_m2_ck
which has no enable_reg
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ssi_l4_ick should have PARENT_CONTROLS_CLOCK flag.
ST_SSI_STDBY bit in idlest register cannot be used in omap2_clk_wait_ready
Signed-off-by: Jouni Högander <jouni.hogander@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Wrong shift values were used for gpio2-6 fclks (gpt2-6 shift).
Signed-off-by: Jouni Högander <jouni.hogander@nokia.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the omap2_set_globals_{242x,243x,343x}() functions. These
functions are called early upon boot in the map_io() functions in the
board-specific init files.
This patch was accidentally left out of the earlier series.
This fixes omap2 booting as noted by Kyungmin Park <kmpark@infradead.org>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kyungmin Park <kmpark@infradead.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
