The GETPARAM ioctl writes to a user supplied address. If that address is
invalid, it is the user's error and not the driver's, so quietly report
EFAULT and don't blame ourselves with a DRM_ERROR.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466773227-7994-11-git-send-email-chris@chris-wilson.co.uk
i915_dma.c used to contain the DRI1/UMS horror show, but now all that
remains are the out-of-place driver level interfaces (such as
allocating, initialising and registering the driver). These should be in
i915_drv.c alongside similar routines for suspend/resume.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466773227-7994-10-git-send-email-chris@chris-wilson.co.uk
drm_connector_register_all() is now automatically called by
drm_dev_register(), and so we no longer have to do so ourselves (via
intel_modeset_register() after calling drm_dev_register()). Similarly
for unregistering.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466773227-7994-8-git-send-email-chris@chris-wilson.co.uk
To complete the transition to manual control of load/unload, we need to
take over unloading from i915_pci_remove(). This allows us to correctly
order our unregister vs shutdown phases, which currently are inverted
due to the midlayer.
However, the unload sequence is still invalid as we shutdown the driver
with the last reference. Ideally, all we want to do is remove the
userspace access on device removal, deferring the cleanup to the
drm_dev_release() - breaking the reference cycles is then left as an
exercise for the reader.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466773227-7994-7-git-send-email-chris@chris-wilson.co.uk
Take control over allocating, loading and registering the driver from the
DRM midlayer by performing it manually from i915_pci_probe. This allows
us to carefully control the order of when we setup the hardware vs when
it becomes visible to third parties (including userspace). The current
ordering makes the driver visible to userspace first (in order to
coordinate with removed DRI1 userspace), but that ordering incurs risk.
The risk increases as we strive for more asynchronous loading.
One side effect of controlling the allocation is that we can allocate
both the drm_device + drm_i915_private in one block, the next step
towards subclassing.
Unload is still left as before, a mix of midlayer and driver.
v2: After drm_dev_init(), we should call drm_dev_unref() so that we call
drm_dev_release() and free everything from drm_dev_init().
v3: Fixup missed error code for failing to allocate dev_priv
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466773227-7994-6-git-send-email-chris@chris-wilson.co.uk
Currently debugfs files are created before the driver is even loads.
This gives the opportunity for userspace to open that interface and poke
around before the backing data structures are initialised - with the
possibility of oopsing or worse.
Move the creation of the debugfs files to our registration phase, where
we announce our presence to the world when we are ready, i.e the
sequence changes from
drm_dev_register()
-> drm_minor_register()
-> drm_debugfs_init()
-> i915_debugfs_init()
-> i915_driver_load()
to
drm_dev_register()
-> drm_minor_register()
-> drm_debugfs_init()
-> i915_driver_load()
-> i915_debugfs_register()
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466773227-7994-5-git-send-email-chris@chris-wilson.co.uk
Currently the backlight is being registered in the load phase (before
the display and its objects are registered). Move the backlight
registration into the analogous phase by performing it from the
connector registration, just after its creation.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466773227-7994-3-git-send-email-chris@chris-wilson.co.uk
With the introduction of a connector->func for callback from
drm_connector_register() we can move all the tasks that we want to do
upon registration into that callback. Later, this will allow us to
reorder the registration and defer it until after the device is setup
and ready for userspace.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466773227-7994-2-git-send-email-chris@chris-wilson.co.uk
Currently setting up the backlight for a panel is sometimes done
together with initialising the panel, and sometimes after the connector
is registered. The backlight setup does not depend upon connector
registration (i.e. access to sysfs/debugfs and the kobject hierachy) so
perform it consistently just after panel initialisation.
Note the discrepancy here as destroying the panel is done during
connector unregistration...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466773227-7994-1-git-send-email-chris@chris-wilson.co.uk
Effectively removes one layer of indirection between the mask of
possible engines and the engine constructors. Instead of spelling
out in code the mapping of HAS_<engine> to constructors, makes
more use of the recently added data driven approach by putting
engine constructor vfuncs into the table as well.
Effect is fewer lines of source and smaller binary.
At the same time simplify the error handling since engine
destructors can run on unitialized engines anyway.
Similar approach could be done for legacy submission is wanted.
v2: Removed ugly BUILD_BUG_ONs in favour of newly introduced
ENGINE_MASK and HAS_ENGINE macros.
Also removed the forward declarations by shuffling functions
around.
v3: Warn when logical_rings table does not contain enough data
and disable the engines which could not be initialized.
(Chris Wilson)
v4: Chris Wilson suggested a nicer engine init loop.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1466689961-23232-1-git-send-email-tvrtko.ursulin@linux.intel.com
Backmerge drm-next for the reworked device register/unregistering.
Chris Wilson needs that to be able to land his i915 load/unload
demidlayering.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
- device tree binding documentation for MT8173 HDMI encoder, CEC, DDC,
and PHY
- drivers for MT8173 HDMI encoder, CEC (HPD only for now), DDC, and PHY
- enable HDMI output via a custom SMCCC call
- add ddc-i2c-bus property to HDMI connector device tree binding
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1TLt
-----END PGP SIGNATURE-----
Merge tag 'mediatek-drm-2016-06-20' of git://git.pengutronix.de/git/pza/linux into drm-next
MT8173 HDMI support
- device tree binding documentation for MT8173 HDMI encoder, CEC, DDC,
and PHY
- drivers for MT8173 HDMI encoder, CEC (HPD only for now), DDC, and PHY
- enable HDMI output via a custom SMCCC call
- add ddc-i2c-bus property to HDMI connector device tree binding
* tag 'mediatek-drm-2016-06-20' of git://git.pengutronix.de/git/pza/linux:
dt-bindings: hdmi-connector: add DDC I2C bus phandle documentation
drm/mediatek: enable hdmi output control bit
drm/mediatek: Add HDMI support
dt-bindings: drm/mediatek: Add Mediatek HDMI dts binding
some rcar-du fixes.
* 'drm/next/du' of git://linuxtv.org/pinchartl/media:
drm: rcar-du: error message is not needed for EPROBE_DEFER
drm: rcar-du: error message is not needed for drm_vblank_init()
rcar-du: add/rename DEFR6 TCON bits
- Infrastructure for GVT-g (paravirtualized gpu on gen8+), from Zhi Wang
- another attemp at nonblocking atomic plane updates
- bugfixes and refactoring for GuC doorbell code (Dave Gordon)
- GuC command submission enabled by default, if fw available (Dave Gordon)
- more bxt w/a (Arun Siluvery)
- bxt phy improvements (Imre Deak)
- prep work for stolen objects support (Ankitprasa Sharma & Chris Wilson)
- skl/bkl w/a update from Mika Kuoppala
- bunch of small improvements and fixes all over, as usual
* tag 'drm-intel-next-2016-06-20' of git://anongit.freedesktop.org/drm-intel: (81 commits)
drm/i915: Update DRIVER_DATE to 20160620
drm/i915: Introduce GVT context creation API
drm/i915: Support LRC context single submission
drm/i915: Introduce execlist context status change notification
drm/i915: Make addressing mode bits in context descriptor configurable
drm/i915: Make ring buffer size of a LRC context configurable
drm/i915: gvt: Introduce the basic architecture of GVT-g
drm/i915: Fold vGPU active check into inner functions
drm/i915: Use offsetof() to calculate the offset of members in PVINFO page
drm/i915: Factor out i915_pvinfo.h
drm/i915: Serialise presentation with imported dmabufs
drm/i915: Use atomic commits for legacy page_flips
drm/i915: Move fb_bits updating later in atomic_commit
drm/i915: nonblocking commit
Reapply "drm/i915: Pass atomic states to fbc update, functions."
drm/i915: Roll out the helper nonblock tracking
drm/i915: Signal drm events for atomic
drm/i915/ilk: Don't disable SSC source if it's in use
drm/i915/guc: (re)initialise doorbell h/w when enabling GuC submission
drm/i915/guc: replace assign_doorbell() with select_doorbell_register()
...
Again a pile of things all over
- Conversion to rst from docbook from Jani. Looks real pretty, and the
source is now actually readable (compared to horrible, horrible docbook
xml)! https://01.org/linuxgraphics/gfx-docs/drm/
- device register/unregister rework from Chris, with follow-up work from
Benjamin. Allows more drivers to demidlayer load/unload and others to
remove a bit of boilerplate.
- master/auth related cleanup, with docs
- some dma-buf polish, merged by Sumit
- small stuff all over (like build fixes from Arnd)
Group maintainership seems to slowly take off, with both Thierry and Sumit
pushing a few things. No hiccups thus far.
* tag 'topic/drm-misc-2016-06-22-updated' of git://anongit.freedesktop.org/drm-intel: (68 commits)
drm/vc4: Remove unused connector
drm/fb-helper: Reduce READ_ONCE(master) to lockless_dereference
drm/sun4i: Remove open-coded drm_connector_register_all()
drm/vc4: Remove open-coded drm_connector_register_all()
drm/atmel-hlcdc: Remove redundant call to drm_connector_unregister_all()
drm: document drm_auth.c
drm: Clear up master tracking booleans
drm: Extract drm_is_current_master
drm: Refactor drop/set master code a bit
drm: Lobotomize set_busid nonsense for !pci drivers
drm: Nuke SET_UNIQUE ioctl
drm: Don't call drm_dev_set_unique from platform drivers
drm/vgem: Stop calling drm_drv_set_unique
drm: Use dev->name as fallback for dev->unique
drm: Clean up drm_crtc.h
drm: Move master pointer from drm_minor to drm_device
drm: sti: rework init sequence
drm: sti: use late_register and early_unregister callbacks
drm/amdkfd: Clean up inline handling
drm: Add callbacks for late registering
...
During hibernation the cached DP port register value will be left with
whatever value we have there when we create the hibernation image.
Currently that means the port (and eDP PLL) will be off in the cached
value. However when we resume there is no guarantee that the value
in the actual register will match the cached value. If i915 isn't
loaded in the kernel that loads the hibernation image, the port may
well be on (eg. left on by the BIOS). The encoder state readout
does the right thing in this case and updates our encoder state
to reflect the actual hardware state. However the post-resume modeset
will then use the stale cached port register value in
intel_dp_link_down() and potentially confuse the hardware.
This was caught by the following assert
WARNING: CPU: 3 PID: 5288 at ../drivers/gpu/drm/i915/intel_dp.c:2184 assert_edp_pll+0x99/0xa0 [i915]
eDP PLL state assertion failure (expected on, current off)
on account of the eDP PLL getting prematurely turned off when
shutting down the port, since the DP_PLL_ENABLE bit wasn't set
in the cached register value.
Presumably I introduced this problem in
commit 6fec766283 ("drm/i915: Use intel_dp->DP in eDP PLL setup")
as before that we didn't update the cached value after shuttting the
port down. That's assuming the port got enabled at least once prior
to hibernating. If that didn't happen then the cached value would
still have been totally out of sync with reality (eg. first boot w/o
eDP on, then hibernate, and then resume with eDP on).
So, let's fix this properly and refresh the cached register value from
the hardware register during resume.
DDI platforms shouldn't use the cached value during port disable at
least, so shouldn't have this particular issue. They might still have
issues if we skip the initial modeset and then try to retrain the link
or something. But untangling this DP vs. DDI mess is a bigger topic,
so let's jut punt on DDI for now.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Fixes: 6fec766283 ("drm/i915: Use intel_dp->DP in eDP PLL setup")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463162036-27931-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
The wait for panel status helper will only function correctly if the
HW panel timings are programmed correctly. Returning prematurely from
this helper may lead to obscure bugs later, so sanity check the HW
timing registers.
v2:
- Check the T8, T9 fields too, we do program them (Ville)
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466096506-11937-1-git-send-email-imre.deak@intel.com
The PPS registers are backed by power well #0 and as such may be reset
after system or runtime suspend (both implying a possible DC9
transition). Fix this by reusing the VLV/CHV PPS pipe-reassignment
logic. The difference on BXT is that the PPS instances are not pipe but
port (or more accurately pin) specific, so we only need to care about
the lost HW state. As opposed to VLV/CHV the SW state is fixed and
initialized during connector init.
This also paves the way towards using the actual port->PPS instance
mapping based on VBT.
This fixes eDP link training errors on BXT after suspend, where we
started the link training too early due to an incorrect T3 (panel power
on) register value.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96436
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466084243-5388-2-git-send-email-imre.deak@intel.com
Move the early PPS initialization calls next to the rest of PPS
initialization steps. This allows us to forgo a duplicated call to
intel_dp_init_panel_power_sequencer_registers() on VLV/CHV.
This will swap the order of DP AUX registration wrt. PPS initialization.
There is an existing race here in case of a user space access via the
DPAUX device node after DP AUX registration and before calling
intel_dp_init_panel_power_sequencer_registers(), but this change won't
make this worse. The fix for this is to separate DP AUX initialization
and registration, that's a separate work already underway.
The order of MST wrt. PPS init as well as the order of
intel_dp_init_panel_power_sequencer_registers() wrt.
intel_edp_panel_vdd_sanitize() also swap, which is ok, there are no
dependencies between these steps.
Suggested by Ville.
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466499109-20240-4-git-send-email-imre.deak@intel.com
The initial DPCD read for eDP detection involves using the PPS, but so
far we only initialized the PPS registers after the DPCD read. The
reason this was done so far is to preserve a possible LVDS PPS HW setup
if LVDS is detected but eDP is not. This is not an issue any more after
the previous patch, so we can move the init earlier now.
This was caught by CI with the PPS sanity checks in place and the
initial eDP DPCD readout waiting for the panel power cycle timeout
without the PPS registers being initialized.
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466499109-20240-3-git-send-email-imre.deak@intel.com
Atm on IBX/CPT we attempt to detect if eDP is present even if LVDS was
already detected and an encoder for it was registered. This involves
trying to read out the eDP DPCD, which in turn needs the same power
sequencer that LVDS uses. Poking at the VDD line at an unexpected time
may or may not interfere with the LVDS panel, but it's probably safer to
prevent this. Registering both an LVDS and an eDP connector would also
present a similar problem accessing the shared PPS at any point later in
an unexpected way.
We also need this to be able fix PPS initialization before its first use
in the next patch. For that we want to be sure that PPS is not in use
by LVDS.
v2:
- Split out the PPS init fix to a separate patch. (Chris)
- Add comment about eDP init depending on LVDS init. (Chris)
- Make the use of the intel_encoder ptr less error prone.
v3:
- Use IBX/CPT reference instead of the incorrect ILK, add a WARN about
this. (Ville)
v4:
- Use a helper to get the lvds encoder instead of opencoding the same.
(Ville)
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v2)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v3)
Link: http://patchwork.freedesktop.org/patch/msgid/1466499109-20240-2-git-send-email-imre.deak@intel.com
Somehow I didn't spot this when pushing :(
Fixes: 398e97994f ("drm/vc4: Remove open-coded drm_connector_register_all()")
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
We are only documenting that the read is outside of the lock, and do not
require strict ordering on the operation. In this case the more relaxed
lockless_dereference() will suffice.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466581572-16608-1-git-send-email-chris@chris-wilson.co.uk
Also extract drm_auth.h for nicer grouping.
v2: Nuke the other comments since they don't really explain a lot, and
within the drm core we generally only document functions exported to
drivers: The main audience for these docs are driver writers.
v3: Limit the exposure of drm_master internals by only including
drm_auth.h where it is neede (Chris).
v4: Spelling polish (Emil).
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
- is_master can be removed, we can compute this by checking allowed_master
(which really just tracks whether a master struct has been allocated
for this fpriv in either open or set_master), and whether the fpriv is
the current master on the device.
- that frees up is_master as a good replacement name for allowed_master.
With that it's clear that it tracks whether the fpriv is a master (with
possibly clients attached to it and authenticated against it), and that
one of those fprivs with is_master set is the current master.
v2: Fix kerneldoc for is_master (Emil).
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466499262-18717-10-git-send-email-daniel.vetter@ffwll.ch
Just rolling out a bit of abstraction to be able to clean
up the master logic in the next step.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
File open/set_maseter ioctl and file close/drop_master ioctl share the
same master handling code. Extract it.
Note that vmwgfx's master_set callback needs to know whether the
master is a new one or has been used already, so thread this through.
On the close/drop side a similar parameter existed, but wasnt used.
Drop it to simplify the flow.
v2: Try to make it not leak so much (Emil).
v3: Send out the right version ...
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466511638-9885-1-git-send-email-daniel.vetter@ffwll.ch
We already have a fallback in place to fill out the unique from
dev->unique, which is set to something reasonable in drm_dev_alloc.
Which means we only need to have a special set_busid for pci devices,
to be able to care the backwards compat code for drm 1.1 around, which
libdrm still needs.
While developing and testing this patch things blew up in really
interesting ways, and the code is rather confusing in naming things
between the kernel code, ioctl #defines and libdrm. For the next brave
dragon slayer, document all this madness properly in the userspace
interface section of gpu.tmpl.
v2: Make drm_dev_set_unique static and update kerneldoc.
v3: Entire rewrite, plus document what's going on for posterity in the
gpu docbook uapi section.
v4: Drop accidental amdgpu hunk (Emil).
v5: Drop accidental omapdrm vblank counter change (Emil).
v6: Rebase on top of the sphinx conversion.
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> (virt_gpu)
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Ever since
commit 2e1868b560315a8b20d688e646c489a5ad93eeae
Author: Eric Anholt <anholt@freebsd.org>
Date: Wed Jun 16 09:25:21 2004 +0000
DRI trunk-20040613 import
the X server supports drm 1.1, thus doesn't call call libdrm's
drmSetBusid - the sole user of this ioctl. When reviewing this note
that for hilarity both the kernel-internal functions (set_busid) and
the libdrm wrapper (drmSetBusid) have names not matching this ioctl
(SET_UNIQUE).
v2: Polish commit message (Emil).
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466499262-18717-6-git-send-email-daniel.vetter@ffwll.ch
Since
commit e112e593b2
Author: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Date: Fri Dec 11 11:20:28 2015 +0100
drm: use dev_name as default unique name in drm_dev_alloc()
we're using a reasonable default which should work for everyone. Only
mtk, rcar-du and sun4i are affected, and as kms-only drivers without
any rendering support no one should ever care about the unique name
v2: Rebase on top of mediatek.
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466499262-18717-5-git-send-email-daniel.vetter@ffwll.ch
Lots of arm drivers get this wrong and for most arm boards this is the
right thing actually. And anyway with most loaders you want to chase
sysfs links anyway to figure out which dri device you want.
This will fix dmesg noise for rockchip and sti.
Also add a fallback to driver->name for entirely virtual drivers like
vgem.
v2: Rebase on top of
commit e112e593b2
Author: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Date: Fri Dec 11 11:20:28 2015 +0100
drm: use dev_name as default unique name in drm_dev_alloc()
and simplify a bit. Plus add a comment.
v3: WARN_ON(!dev->unique) as discussed with Emil.
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Reported-by: Ilia Mirkin <imirkin@alum.mit.edu>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v2)
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466499262-18717-3-git-send-email-daniel.vetter@ffwll.ch
- Group declarations for separate files (drm_bridge.c, drm_edid.c)
- Move declarations only used within drm.ko to drm_crtc_internal.h
- drm_property_type_valid to drm_crtc.c, its only callsite
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466499262-18717-2-git-send-email-daniel.vetter@ffwll.ch
There can only be one current master, and it's for the overall device.
Render/control minors don't support master-based auth at all.
This simplifies the master logic a lot, at least in my eyes: All these
additional pointer chases are just confusing.
While doing the conversion I spotted some locking fail:
- drm_lock/drm_auth check dev->master without holding the
master_mutex. This is fallout from
commit c996fd0b95
Author: Thomas Hellstrom <thellstrom@vmware.com>
Date: Tue Feb 25 19:57:44 2014 +0100
drm: Protect the master management with a drm_device::master_mutex v3
but I honestly don't care one bit about those old legacy drivers
using this.
- debugfs name info should just grab master_mutex.
- And the fbdev helper looked at it to figure out whether someone is
using KMS. We just need a consistent value, so READ_ONCE. Aside: We
should probably check if anyone has opened a control node too, but I
guess current userspace doesn't really do that yet.
v2: Balance locking, reported by Julia.
v3: Rebase on top of Chris' oops fixes.
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v2)
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466499262-18717-1-git-send-email-daniel.vetter@ffwll.ch
Use drm_dev_alloc() and drm_dev_register() instead of .load()
To simplify init sequence only create fbdev when requested
in output_poll_changed().
version 2:
remove call to drm_connector_unregister_all() and
drm_dev_set_unique()
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466514580-15194-4-git-send-email-benjamin.gaignard@linaro.org
Make sti driver use register callback to move debugfs
initialization out of sub-components creation.
This will allow to convert driver .load() to
drm_dev_alloc() and drm_dev_register().
sti_compositor bring up 2 crtc but only one debugfs init is
needed so use drm_crtc_index to do it on the first one.
This can't be done in sti_drv because only sti_compositor have
access to the devices.
It is almost the same for sti_encoder which handle multiple
encoder while one only debugfs entry is needed so add a boolean
to avoid multiple debugfs initialization
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466514580-15194-3-git-send-email-benjamin.gaignard@linaro.org
- inline functions need to be static inline, otherwise gcc can opt to
not inline and the linker gets unhappy.
- no forward decls for inline functions, just include the right headers.
Cc: Oded Gabbay <oded.gabbay@gmail.com>
Cc: Ben Goz <ben.goz@amd.com>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466500235-21282-2-git-send-email-daniel.vetter@ffwll.ch
Like what has been done for connectors add callbacks on encoder,
crtc and plane to let driver do actions after drm device registration.
Correspondingly, add callbacks called before unregister drm device.
version 2:
add drm_modeset_register_all() and drm_modeset_unregister_all()
to centralize all calls
version 3:
in error case unwind registers in drm_modeset_register_all
fix uninitialed return value
inverse order of unregistration in drm_modeset_unregister_all
version 4:
move function definitions in drm_crtc_internal.h
remove not needed documentation
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466519829-4000-1-git-send-email-benjamin.gaignard@linaro.org
No need for local struct drm_device * since dev_priv is the
correct thing to pass in to NEEDS_WaRsDisableCoarsePowerGating
anyway. Changed the macro definition for the latter to reflect
that as well.
v2: Alignment bikeshed.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466518034-24838-1-git-send-email-tvrtko.ursulin@linux.intel.com
Commit 7566e24767 ("drm/fsl-dcu: handle initialization errors properly")
introduced error handling during initialization, but with a wrong cleanup
order.
Replace the error handling with the generic cleanup function
drm_mode_config_cleanup.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160619021543.23587-1-stefan@agner.ch
We get a harmless build warning when trying to use the mediatek DRM
driver with IOMMU support disabled:
warning: (DRM_MEDIATEK) selects IOMMU_DMA which has unmet direct dependencies (IOMMU_SUPPORT)
However, the IOMMU_DMA symbol is not meant to be used by drivers at all,
and this driver doesn't seem to have a strict dependency on it other
than using the mediatek IOMMU driver that does.
Since we also want to be able to do compile tests with the driver on
other platforms, the IOMMU_DMA symbol should not be selected here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462997501-982363-1-git-send-email-arnd@arndb.de
