Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to igb, ixgbe, ixgbevf, i40e and i40evf.
Anjali provides a i40e/i40evf patch to add Energy Efficient Ethernet
Low Power Idle stats and a fix for i40e to change the string
"Side Band" to "Sideband" for consistency.
Mitch provides 2 patches for i40evf to fix if the driver encounters
an error while communicating with the PF driver, do not shut down the
admin queue unconditionally. Add an error message when the admin
queue message never completes and fix formatting on another message
that was unnecessarily wrapped.
Mark provides a ixgbe patch and five ixgbevf patches. Fix a possible
infinite recursion when an adapter is removed and registers all read
as all one's in ixgbe_clear_vmdq_generic() and ixgbe_clear_rar_generic().
Converts macros to static inline functions to align kernel coding standard
and prepare for adding Live Error Recovery (LER) to ixgbevf. Change the
ethtool register test to use the normal register accessor functions and
eliminate macors used for calling register test functions to make error
exits more clear. Checks all register reads for adapter removal by checking
the status register after any register read that returns all F's since the
status register will never return 0xFFFFFFFF unless the adapter is removed.
Jacob implements SIOCGHWTSTAMP ioctl for igb which enables user processes
to read the current hardware stamp config settings non-destructively.
Todd adds the initial register read and write for surprise removal (LER)
for igb.
Christian Engelmayer fixes an igb memory leak in the igb_get_module_eeprom()
error handling path.
Ken Ichikawa provides a fix for igb, specifically for 82575 hardware to
specify -1 to the phc_index for ethtool's get_ts_info, otherwise a wrong
value will be set to the phc_index.
Christopher Paasch fixes a null pointer dereference in igb and makes sure
to unset the HAS_MSIX flag when the driver falls back to MSI only.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As commit a6e28b34205b("staging/et131x: use SET_ETHTOOL_OPS
directly"), using a wrapper around SET_ETHTOOL_OPS macro is
not actually required, remove and use SET_ETHTOOL_OPS directly.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses two typos in the original driver submission. One derived
from a cut & paste error, and another is a misspelling.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses a portable pointer arithmetic issue in the
original submission found by the kbuild test robot.
config: make ARCH=i386 allyesconfig
altera_sgdma.c: In function 'sgdma_txphysaddr':
>> altera_sgdma.c:393:33: warning: cast from
>> pointer to integer of different size [-Wpointer-to-int-cast]
dma_addr_t offs = (dma_addr_t)((dma_addr_t)desc -
^
>> altera_sgdma.c:394:5: warning: cast from
>> pointer to integer of different size [-Wpointer-to-int-cast]
(dma_addr_t)priv->tx_dma_desc);
^
altera_sgdma.c: In function 'sgdma_rxphysaddr':
>> altera_sgdma.c:403:33: warning: cast from
>> pointer to integer of different size [-Wpointer-to-int-cast]
dma_addr_t offs = (dma_addr_t)((dma_addr_t)desc -
^
>> altera_sgdma.c:404:5: warning: cast from
>> pointer to integer of different size [-Wpointer-to-int-cast]
(dma_addr_t)priv->rx_dma_desc);
^
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the version number returned by the driver's get regs routine
invoked by ethtool so formatting can be dependent on the version
number returned, and any interesting formatted output can check
the version number for specific types of register data returned.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds Rx checksum offload support for VXLAN.
Implements .ndo_{add|del}_vxlan_port netdev ops.
Adapter supports only one VXLAN port, so program adapter with
very first UDP port which VXLAN driver is listening to.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds LSO, LSO6 and Tx checksum offload support for VXLAN
encapsulated packets on 83xx/84xx series adapters.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The P1010 device tree restricts the number of
supported interrupt groups to 1, although the eth
controller can support 2 interrupt groups and the
driver assumes the Multi-Group mode ("fsl,etsec2" model).
So, in this case the assumption that the Multi-Group
mode (MQ_MG_MODE) devices always support 2 interrupt
groups is false. To fix this, a check for the actual
number of interrupt groups enabled in the board's
device tree has been added in gfar_probe for the
"fsl,etsec2" devices.
Without this fix, P1010 based boards claim support for
2 Tx queues to the net stack but only one is actually
allocated, leading to NULL access in xmit. This issue
was introduced by enabling Single-Queue polling for
the P1010 devices.
(71ff9e3 gianfar: Use Single-Queue polling for
"fsl,etsec2")
Fixes: 71ff9e3df7
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Few platforms use external regulator to keep the ethernet MAC supplied.
So, request and enable the regulator for driver functionality.
Fixes: 66fda75f47 (regulator: core: Replace direct ops->disable usage)
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Suggested-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the many PTP Hardware Clock drivers with the
newly introduced field that advertises the number of programmable
pins. Some of these devices do have programmable pins, but the
implementation will have to wait for follow on patches.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When igb_set_interrupt_capability() calls
igb_reset_interrupt_capability() (e.g., because CONFIG_PCI_MSI is unset),
num_q_vectors has been set but no vector has yet been allocated.
igb_reset_interrupt_capability() will then call igb_reset_q_vector,
which assumes that the vector is allocated. As this is not the case, we
are accessing a NULL-pointer.
This patch fixes it by checking that q_vector is indeed different from
NULL.
Fixes: 02ef6e1d0b (igb: Fix queue allocation method to accommodate changing during runtime)
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
82575 has only software timestamping capability and it has
no PTP Hardware Clocks. Therefore, -1 has to be specified
to the phc_index for ethtool's get_ts_info, otherwise a wrong
value will be set to the phc_index.
v2: move the if (adapter->ptp_clock) section specifying phc_index
to above the switch statement as suggested by Matthew Vick.
adapter->ptpclock will always be NULL for 82575.
Signed-off-by: Ken ICHIKAWA <ichikawa.ken@jp.fujitsu.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a memory leak in the igb_get_module_eeprom() error handling path.
Detected by Coverity: CID 1016508.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for the SIOCGHWTSTAMP ioctl which enables user
processes to read the current hwtstamp_config settings
non-destructively. Previously a process had to be privileged and could
only set values, it couldn't return what is currently set without
possibly overwriting the value.
This patch adds support for this new operation into igb by keeping a
shadow copy of the config in the adapter structure, which is returned
upon request.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Additional checks are needed for a detected removal not to cause
problems. Some involve simply avoiding a lot of stuff that can't
do anything good, and also cases where the phony return value can
cause problems. In addition, down the adapter when the removal is
sensed.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Prevent writes to an adapter that has been detected as removed
by a previous failing read.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check all register reads for adapter removal by checking the status
register after any register read that returns 0xFFFFFFFF. Since the
status register will never return 0xFFFFFFFF unless the adapter is
removed, such a value from a status register read confirms the
removal. Since this patch adds so much to ixgbe_read_reg, stop
inlining it, to reduce driver bloat.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make the ethtool register test use the normal register accessor
functions. Also eliminate macros used for calling register test
functions to make error exits clearer.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Kernel coding standard prefers static inline functions instead
of macros, so use them for register accessors. This is to prepare
for adding LER, Live Error Recovery, checks to those accessors.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When an adapter is removed and registers all read as all one's,
an infinite recursion can happen between ixgbe_clear_vmdq_generic
and ixgbe_clear_rar_generic. Adding a check for removal breaks
this recursion.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add an error message when the admin queue message never completes, and
fix formatting on another one that was unnecessarily wrapped.
Change-ID: I8b8a4eb7629d741f09357250144023cd4a72231f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the driver encounters an error while communicating with the PF
driver, don't just shut down the admin queue unconditionally. The PF
may be delayed, and shutting down the admin queue causes it to fail
completely. If this happens, the VF will never complete initialization.
Change-ID: I6192e9d8caeefb738428c3597fa2f54fa400ce7f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of always invoking netdev_get_tx_queue() in bcmgenet_xmit() and
bcmgenet_tx_reclaim(), just get the corresponding netdev_queue pointer
once and for all and manipulate it throughout bcmgenet_xmit() and
bcmgenet_tx_reclaim().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev_pick_tx already takes care of making sure that a given
skb->queue_mapping value will remain within the number of advertised
hardware queue number, there is no need to re-do this again in the
driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCMGENET driver was not TX timestamping the SKBs it queued for
transmission, do this in bcmgenet_xmit() right before kicking the
Transmit DMA engine.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The spinlock cookie in bcmgenet_priv is never used, get rid of it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"goto" is well accepted for error paths in the kernel but should not be
used unnecessarily. Return the correct value directly instead of using a
goto when possible.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Network API functions that rely on the MDIO bus can be called as soon as
the driver calls register_netdev(). Register the MDIO bus before the
network device to avoid race conditions.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network device passed to the sh_mdio_init and sh_mdio_release
functions is only used to access the sh_eth_private instance. Pass it
directly to those functions.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO bus parent is set to the network device. Beside not reflecting
the hardware topology, this prevents registering the MDIO bus before
initializing the network device. Fix it by setting the MDIO bus parent
to the platform device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Memory allocated for the MDIO bus with the devm_kzalloc() API is
associated with the network device. While this will cause memory to be
freed at the right time, it doesn't allow allocating memory before the
network device is initialized.
Replace the network device with the parent platform device for memory
allocation to remove that dependency. This also improves consistency
with the other devm_* calls in the driver that all use the platform
device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new syntax is added for the module parameters num_vfs and probe_vf.
num_vfs=p1,p2,p1+p2
probe_bf=p1,p2,p1+p2
Where p1(2) is the number of VFs on / probed VFs for physical
port1(2) and p1+p2 is the number of dual port VFs.
Single port VFs are currently supported only when the link type
for both ports of the device is Ethernet.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for N-Port VFs, this includes:
1. Adding support in the wrapped FW command
In wrapped commands, we need to verify and convert
the slave's port into the real physical port.
Furthermore, when sending the response back to the slave,
a reverse conversion should be made.
2. Adjusting sqpn for QP1 para-virtualization
The slave assumes that sqpn is used for QP1 communication.
If the slave is assigned to a port != (first port), we need
to adjust the sqpn that will direct its QP1 packets into the
correct endpoint.
3. Adjusting gid[5] to modify the port for raw ethernet
In B0 steering, gid[5] contains the port. It needs
to be adjusted into the physical port.
4. Adjusting number of ports in the query / ports caps in the FW commands
When a slave queries the hardware, it needs to view only
the physical ports it's assigned to.
5. Adjusting the sched_qp according to the port number
The QP port is encoded in the sched_qp, thus in modify_qp we need
to encode the correct port in sched_qp.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the following utils:
1. Convert slave_id -> VF
2. Get the active ports by slave_id
3. Convert slave's port to real port
4. Get the slave's port from real port
5. Get all slaves that uses the i'th real port
6. Get all slaves that uses the i'th real port exclusively
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the required data structures to support VFs with N (1 or 2)
ports instead of always using the number of physical ports.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since passing the clock is not mandatory, change the warning message to debug,
so that we avoid getting the following clock failure message on every boot:
smsc911x: Driver version 2008-10-21
smsc911x smsc911x (unregistered net_device): couldn't get clock -2
libphy: smsc911x-mdio: probed
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the call to enable Tx queues after the link is established.
Previously there was a chance for aggressive start_ndo_xmit() callers to
sneak packets between enabling the Tx queues and the link coming up.
In addition it replaces netif_tx_start_all_queues() with
netif_tx_wake_all_queues() to allow for flushing of the qdisc.
CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We use to cache whether the MNG FW was enabled, how since this isn't
static we really need to verify with each check. This patch makes that
change.
CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rather than assign several parameters in a row, we should use a for
loop, which reduces code size.
CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch replaces some direct uses of pci_read_config_word with the
protected ixgbe_read_pci_cfg_word function, which checks for whether the
adapter is removed when LER is enabled. We shouldn't use the
pci_read_config_word calls directly because of these checks.
This patch also cleans up an unnecessary save of a pointer to the mac
object, as our standard style is to just use the hw pointer.
CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch reverts the addition of the fiber_fixed type, which ended up
never being used. We don't have plans to support this type going
forward, and there is no reason to keep an unused type around polluting
the code.
Reverts: 4e8e1bca6e ("ixgbe: add new media type")
CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes flow control autonegotiation for KR/KX/K4 interfaces.
When setting up MAC link, the cached autoc value and current autoc value
were being incorrectly used to determine whether link reset is required.
This resulted in the driver ignoring and discarding flow control
negotiation changes that occur since the caching happened, as well as
when the mac was being setup.
This patch also splits the assignments for the 3 autoc variables into
their own block, and adds a comment explaining what each one means, in
order to help keep logic more straightforward while reading the code.
CC: Arun Sharma <asharma@fb.com>
Reported-by: Sourav Chatterjee <sourav.chatterjee@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously, we did a full check to see if MNG FW was running. Instead,
we should only check to see whether it could be enabled. Since it may
become active while down, we don't want to bring the link down.
CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch corrects the stop_mac_link_on_d3 function in ixgbe_82599 by
checking the Core Clock Disable bit before stopping link.
CC: Arun Sharma <asharma@fb.com>
Reported-by: Chris Pavlas <chris.pavlas@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Found several incorrect conditionals after calling the prot_autoc_*
functions. Likewise we weren't always freeing the FWSW semaphore after
grabbing it. This would lead to DA cables being unable to link along with
possible other errors.
CC: Arun Sharma <asharma@fb.com>
CC: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For i350 VLAN stripping for VMs is not enabled in the VMOLR register but in
the DVMOLR register. Making the changes accordingly. It's not necessary to
unset the E1000_VMOLR_STRVLAN bit on i350 as the hardware will simply ignore
it.
Without this change if a VLAN is configured for a VF assigned to a guest
via (i.e.)
ip link set p1p1 vf 0 vlan 10
the VLAN tag will not be stripped from packets going into the VM. Which they
should be because the VM itself is not aware of the VLAN at all.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbevf_down function can now prevent multiple executions by
doing test_and_set_bit on __IXGBEVF_DOWN. This did not work before
introduction of the __IXGBEVF_REMOVING bit, because of overloading
of __IXGBEVF_DOWN. Also add smp_mb__before_clear_bit call before
clearing the __IXGBEVF_DOWN bit.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a bit, __IXGBEVF_REMOVING, to indicate that the module is being
removed. The __IXGBEVF_DOWN bit had been overloaded for this purpose,
but that leads to trouble. A few places now check both __IXGBEVF_DOWN
and __IXGBEVF_REMOVING.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Inline with the current use for ixgbe_read_pci_cfg_word, create a
similar function for writing PCI config, which checks whether the
adapter has been removed first, if Live Error Recovery has been enabled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds defines needed for implementing the auxiliary time sync
functions and also changes code to call the updated defines instead of
the old.
Reported-by: Richard Cochran <ricahrdcochran@gmail.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch causes the TCTL to be explicitly set to fix a problem with
poor network performance (throughput) on certain silicon when configured
for 100M HDX performance.
Cc: Todd Fujinaka <todd.fujinaka@intel.com>
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce W. Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The check for pending Tx work when link is lost was mistakenly moved to be
done only when link is first detected to be lost. It turns out there is a
small window of opportunity for additional Tx work to get queued up shortly
after link is dropped.
Move the check back to the place it was before in the watchdog task. Put in
additional debug information for other reset paths and a final catch-all for
false hangs in the scheduled function that prints out the hardware hang
message.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump to version 0.3.36 for i40e and 0.9.16 for i40evf.
Change-ID: I7b4ff97b32d2825181803c03c316381a7608a618
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If "vf_id" is smaller than hw->func_caps.vf_base_id then it leads to
an array underflow of the pf->vf[] array. This is unlikely to happen
unless the hardware is bad, but it's a small change and it silences a
static checker warning.
Fixes: 7efa84b7ab ('i40e: support VFs on PFs other than 0')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't need context descriptors for every packet, only tso
or timesync. This fixes a bug in the driver where it would
always add a context even if all the passed in values
to the context descriptor function were 0/default values.
Change-ID: I0101d2b893380707b5c2de61aab3e16d4310e9a1
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hardware supports a feature to avoid updating the descriptor
ring by marking each descriptor with a DD bit, and instead
writes a memory location with an update to where the driver
should clean up to. Enable this feature.
Change-ID: I5da4e0681f0b581a6401c950a81808792267fe57
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up and moves a portion of i40e_open to i40e_vsi_open,
in order to have a shorter vsi_open function that does only that.
Change-ID: I1c418dda94dcfc0eb7d4386a70c330692ef5ecc9
Signed-off-by: Elizabeth Kappler <elizabeth.m.kappler@intel.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This enables option '-k/-K' in ethtool for NTUPLE control.
NTUPLE control requires a reset, to take effect. When the feature is
turned off, the SW list of stored FD SB filters gets cleaned up.
Change-ID: I9d564b67a10d4afa11de3b320d601c3d2e6edc1f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Checkpatch complained in an earlier patch about using min(), but that
change would have been completely unrelated to the point of that patch.
So fix it here.
Change-ID: I2cd87b39cfd406850d283b88f259757a6bcd14cd
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The HLUT programming loop in in i40evf_configure_rss was a) overly-
complicated, and b) just plain broken. Most of the entries ended up being
not written at all, so most of the flows ended up at queue zero.
Refactor the HLUT programming loop to simply walk through the registers
and write four values to each one, incrementing through the number of
available queues.
Change-ID: I75766179bc67e4e997187794f3144e28c83fd00d
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This netdev op allows the PF driver to control the virtual link state of
the VF devices. This can be used to deny naughty VF drivers access to
the wire, or to allow VFs (regardless of temperament) to communicate
with each other over the device's internal switch even though external
link is down.
Add the actual ndo function, and modify vc_notify_link_state to check
the link status of each VF before sending a message in the case when
physical link changes state.
Change-ID: Ib5a6924da78c540789f21d26b5e8086d71c29384
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, via-rhine fails to call pci_disable_device() for errors
in rhine_init_one().
Reported-by: Huqiu Liu <liuhq11@mails.tsinghua.edu.cn>
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pci_iounmap instead of iounmap when the virtual mapping was done
with pci_iomap. A simplified version of the semantic patch that finds this
issue is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
expression addr;
@@
addr = pci_iomap(...)
@rr@
expression r.addr;
@@
* iounmap(addr)
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bnx2/bnx2x rings are made up of linked pages. However there is an
upper limit on the page size as some the page size settings are 16-bit
in the hardware/firmware interface. In the current code, some parts
use BNX2_PAGE_SIZE which has a 16K upper limit and some parts use
PAGE_SIZE. On archs with >= 64K PAGE_SIZE, it generates some compile
warnings. Define a new CNIC_PAGE_SZIE which has an upper limit of
16K and use it consistently in all relevant parts.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For per device operations, cnic needs to dereference the RCU protected
cp->ulp_ops instead of the global cnic_ulp_tbl. In 2 locations,
cnic_send_nlmsg() and cnic_copy_ulp_stats(), it was referencing the
global table. If the device has been unregistered and these functions
are still being called (very unlikely scenarios), it could lead to NULL
pointer dereference.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In generic, after an assignment, we use ';' instead of ','.
Although, it won't hurt.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The networking core does it for the driver during registration time.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When compiling the i40e and the i40evf driver into the same kernel I get:
LD drivers/net/ethernet/intel/built-in.o
drivers/net/ethernet/intel/i40evf/built-in.o:(.data+0x300): multiple definition of `i40e_ptype_lookup'
drivers/net/ethernet/intel/i40e/built-in.o:(.data+0x780): first defined here
make[3]: *** [drivers/net/ethernet/intel/built-in.o] Error 1
make[2]: *** [drivers/net/ethernet/intel] Error 2
make[1]: *** [drivers/net/ethernet/] Error 2
make: *** [sub-make] Error 2
Fix this by renaming the i40evf version of this structure from
i40e_ptype_lookup to i40evf_ptype_lookup.
This build failure was introduced in:
commit 206812b5fc
Author: Jesse Brandeburg <jesse.brandeburg@intel.com>
i40e/i40evf: i40e implementation for skb_set_hash
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Eric W Biederman <ebiederm@xmission.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 2800209994 (e1000e: Refactor PM flows) changed the
SET_SYSTEM_SLEEP_PM_OPS to open-coded assignment, but forgot to
protect them with CONFIG_PM_SLEEP. Then cause the following build
error when PM is disabled:
drivers/net/ethernet/intel/e1000e/netdev.c:7079:13:
error: 'e1000e_pm_suspend' undeclared here (not in a function)
.suspend = e1000e_pm_suspend,
^
drivers/net/ethernet/intel/e1000e/netdev.c:7080:13:
error: 'e1000e_pm_resume' undeclared here (not in a function)
.resume = e1000e_pm_resume,
^
drivers/net/ethernet/intel/e1000e/netdev.c:7082:11:
error: 'e1000e_pm_thaw' undeclared here (not in a function)
.thaw = e1000e_pm_thaw,
^
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Command line parameters QueuePairs, Node, EEE, DMAC and InterruptThrottleRate
do not exist these days. Remove all references to them in the Documentation
folder and update code comments.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit f280e89a (drivers: net: cpsw: fix for cpsw crash when build as modules)
moved cpts_register()/cpts_unregister() to ndo_open()/ndo_stop(), but failed
to remove cpts_register in cpsw_probe() which leads to a double registration
and the following debug object splat.
[ 18.991902] ODEBUG: init active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x2c
[ 19.082249] [<c0059e80>] (init_timer_key) from [<c04965d4>] (cpts_register+0x1f0/0x2c4)
[ 19.090642] [<c04965d4>] (cpts_register) from [<c04931dc>] (cpsw_ndo_open+0x780/0x81c)
[ 19.098948] [<c04931dc>] (cpsw_ndo_open) from [<c0599c2c>] (__dev_open+0xb4/0x118)
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the Ethernet Makefile and Kconfig files to add the Altera
Ethernet driver component.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the Altera Triple Speed Ethernet Makfile and
Kconfig file.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the main driver and header file for the Altera Triple
Speed Ethernet driver.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds miscellaneous files for the Altera Ethernet Driver,
including ethtool support.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the SGDMA soft IP support for the Altera Triple
Speed Ethernet driver.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the MSGDMA soft IP support for the Altera Triple
Speed Ethernet driver.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. For the 64 bits dma mask use dma_set_mask_and_coherent instead of
dma_set_mask and dma_set_coherent_mask.
2. For the 32 bits dma mask dma_set_coherent_mask is only called if
dma_set_mask fails, which is unusual. Assuming this as a bug, fixes
it by replacing calls to dma_set_mask and dma_set_coherent_mask by a
call to dma_set_mask_and_coherent.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Tested-by: Jonas Hahnfeld <hahnjo@hahnjo.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we call netdev_*() under netif_msg_*() checks, we can fold these into
netif_*() macro invocations.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert dev_*(&ndev->dev, ...) to netdev_*(ndev, ...) calls since they are a bit
shorter and at the same time give more information on a device.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert pr_*() to netdev_*() calls as the latter provide info on a device.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Exit the driver's probe() method when the register layout is unknown as the
driver would cause kernel oops in this case anyway.
While at it, move the corresponding error message printout and convert it from
pr_err() to dev_err().
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current logic suffers from a slow response time to disable user DB
usage, and also fails to avoid DB FIFO drops under heavy load. This commit
fixes these deficiencies and makes the avoidance logic more optimal.
This is done by more efficiently notifying the ULDs of potential DB
problems, and implements a smoother flow control algorithm in iw_cxgb4,
which is the ULD that puts the most load on the DB fifo.
Design:
cxgb4:
Direct ULD callback from the DB FULL/DROP interrupt handler. This allows
the ULD to stop doing user DB writes as quickly as possible.
While user DB usage is disabled, the LLD will accumulate DB write events
for its queues. Then once DB usage is reenabled, a single DB write is
done for each queue with its accumulated write count. This reduces the
load put on the DB fifo when reenabling.
iw_cxgb4:
Instead of marking each qp to indicate DB writes are disabled, we create
a device-global status page that each user process maps. This allows
iw_cxgb4 to only set this single bit to disable all DB writes for all
user QPs vs traversing the idr of all the active QPs. If the libcxgb4
doesn't support this, then we fall back to the old approach of marking
each QP. Thus we allow the new driver to work with an older libcxgb4.
When the LLD upcalls iw_cxgb4 indicating DB FULL, we disable all DB writes
via the status page and transition the DB state to STOPPED. As user
processes see that DB writes are disabled, they call into iw_cxgb4
to submit their DB write events. Since the DB state is in STOPPED,
the QP trying to write gets enqueued on a new DB "flow control" list.
As subsequent DB writes are submitted for this flow controlled QP, the
amount of writes are accumulated for each QP on the flow control list.
So all the user QPs that are actively ringing the DB get put on this
list and the number of writes they request are accumulated.
When the LLD upcalls iw_cxgb4 indicating DB EMPTY, which is in a workq
context, we change the DB state to FLOW_CONTROL, and begin resuming all
the QPs that are on the flow control list. This logic runs on until
the flow control list is empty or we exit FLOW_CONTROL mode (due to
a DB DROP upcall, for example). QPs are removed from this list, and
their accumulated DB write counts written to the DB FIFO. Sets of QPs,
called chunks in the code, are removed at one time. The chunk size is 64.
So 64 QPs are resumed at a time, and before the next chunk is resumed, the
logic waits (blocks) for the DB FIFO to drain. This prevents resuming to
quickly and overflowing the FIFO. Once the flow control list is empty,
the db state transitions back to NORMAL and user QPs are again allowed
to write directly to the user DB register.
The algorithm is designed such that if the DB write load is high enough,
then all the DB writes get submitted by the kernel using this flow
controlled approach to avoid DB drops. As the load lightens though, we
resume to normal DB writes directly by user applications.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original work by Anand Priyadarshee <anandp@chelsio.com>.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the bh safe variant with the hard irq safe variant.
We need a hard irq safe variant to deal with netpoll transmitting
packets from hard irq context, and we need it in most if not all of
the places using the bh safe variant.
Except on 32bit uni-processor the code is exactly the same so don't
bother with a bh variant, just have a hard irq safe variant that
everyone can use.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/r8152.c
drivers/net/xen-netback/netback.c
Both the r8152 and netback conflicts were simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
In Linux 3.13, dma_set_mask_and_coherent was introduced, and we have
been encouraged to use it. It simplifies the DMA mapping code a bit as
well.
Change-ID: I66e340245af7d0dedfa8b40fec1f5e352754432e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that the 2.4 firmware reports the correct number of MSI-X vectors,
use this value correctly when communicating with the VF, and when
setting up the interrupt linked list.
The PF has always reported the correct number of MSI-X vectors, so we
should never increment the value in the vf driver.
Change-ID: Ifeefc631c321390192219ce2af9ada6180c1492f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We have a separate handler for MDD events, a generic reset is not required.
Change-ID: I77858e2d479e4e65c52aede67109464649ea0253
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The FDIR replay logic was being run a little too soon (before the
queues were enabled) and hence the tail bump was not effective till
a later transaction happened on the queue.
Change-ID: Icfd7cd2e79fc3cae3cbd3f703a2b3a148b4e7bf6
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add code to enforce the following policy:
- If the HW reports filter programming error, we check if it's due to a
full table.
- If so, we go ahead and turn off new rule addition for ATR and then SB
in that order.
- We monitor the programmed filter count, if enough room is created due
to filter deletion/reset, we then re-enable SB and ATR new rule addition.
Change-ID: I69d24b29e5c45bc4fa861258e11c2fa7b8868748
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This variable is a bit mask. It is needed to differentiate between
user enforced feature disables and auto disable of features due to
HW resource limitations.
Change-ID: Ib4b4f6ae1bb2668c12e482d2555100bc8ad713d5
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In a similar way to how ixgbe works, print a short one-line string
showing what features and number of queues the driver and hardware has
enabled at probe time.
Example (wrapped for the commit message):
i40e 0000:06:00.1: Features: PF-id[1] VFs: 64 VSIs: 66 QP: 32 FDir RSS
ATR NTUPLE DCB
Change-ID: I177bf7f93d1c4c921529c92fdf66e614f6b4f755
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up the strings that the driver prints during normal
operation and moves many strings into dev_dbg. It also cleans up
strings printed during reset.
Change-ID: I1835cc4e3c3b22596182b683284e6bb87eac61b2
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This cleans up strings for consistency, q is replaced with queue.
Change-ID: Ia5f9dfae9af261f4c24485854264e02363729cf3
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1) Fix a name of the error bit to correctly indicate the error.
2) Added a fd_id field in the 32 byte desc at the place(qw0) where it gets
reported in the programming error desc WB. In a normal data desc
the fd_id field is reported in qw3.
Change-ID: Ide9a24bff7273da5889c36635d629bc3b5212010
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The update filter logic was causing a kernel panic in the original code.
We need to compare the input set to decide whether or not to delete a
filter since we do not have a hash stored. This new design helps fix the issue.
Change-ID: I2462b108e58ca4833312804cda730b4660cc18c9
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We've been deleting the netdev before getting around to deleting the napi
structs. Unfortunately, we then didn't delete the napi structs because we
have a check for netdev, thus we were leaving garbage around in the system.
Change-ID: Ife540176f6c9f801147495b3f2d2ac2e61ddcc58
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the sh_eth device is registered using OF, then the driver
should call of_mdiobus_register() to register the PHYs described
in the devicetree and then use of_phy_connect() to connect the
PHYs to the device.
This ensures that any PHYs registered in the device tree are
appropriately connected to the parent devices nodes so that
the PHY drivers can access their OF properties.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the Freescale fec is in promiscuous mode and network cable is
reconnected then the promiscuous mode get lost. The problem is caused
by a too soon call of set_multicast_list to re-enable promisc mode.
The FEC_R_CNTRL register changes are overwritten by fec_restart.
This patch fixes this by moving the call behind the init of FEC_R_CNTRL
register in fec_restart.
Successful tested on a i.MX28 board.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcm_enet_netpoll does not exist, and causing
bcm63xx_net to fail to build when NET_POLL_CONTROLLER
is defined.
Remove the bogus .ndo_poll_controller = bcm_enet_netpoll
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to igb, e1000e, ixgbe and ixgbevf.
Tom Herbert provides changes to e1000e, igb and ixgbe to call skb_set_hash()
to set the hash and its type in an skbuff.
Carolyn provides a fix for igb where using ethtool for EEE settings, which
was not working correctly.
Jacob provides some trivial cleanups and fixes for ixgbe which mainly
dealt with the file headers.
Julia Lawall provides a one fix for ixgbevf where the driver did not need
to adjust the power state on suspend, so the call to pci_set_power_state()
in the resume function was a no-op.
v2:
- dropped patches 4-6 from original series which implemented debugfs for
igb from Carolyn based on feed back from David Miller and Or Gerlitz
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0034b29 ("cxgb4: Don't assume LSO only uses SGL path in t4_eth_xmit()")
introduced a regression where-in length was calculated wrongly for LSO path,
causing chip hangs.
So, correct the calculation of len.
Fixes: 0034b29 ("cxgb4: Don't assume LSO only uses SGL path in t4_eth_xmit()")
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We'd come in with SGE_FL_BUFFER_SIZE[0] and [1] both equal to 64KB and the
extant logic would flag that as an error.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mlx4_en_stop_port() is called, we need to deregister also the
tunnel steering rules that relate to multicast.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver does not need to adjust the power state on suspend, so the
call to pci_set_power_state in the resume function is a no-op. Drop it,
to make the code more understandable.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes some formatting on multilined print messages, so that
the text of the print appears on a single line, which aids in grepping
the sourcecode for where the error came from.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The header above this function did not match the function prototype.
This patch rewords the comment to specify the correct parameters.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch updates the contact information on the ixgbe driver files so
that every file includes the Linux NICS address, as it is still used,
but only a few of the files mentioned it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
cppcheck detected following warning in ixgbe_fcoe.c
(warning) %d in format string (no. 1) requires 'int' but the
argument type is 'unsigned int'.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Tested-By: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Tom Herbert <therbert@google.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem where using ethtool for EEE setting was not
working correctly. This patch also fixes a problem where
the function that checks for EEE status on i354 devices was not being
called and was causing warnings with static analysis tools.
Reported-by: Rashika Kheria <rashika.kheria@gmail.com>
Reported-by: Josh Triplett <josh@joshtriplett.org>
Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Tom Herbert <therbert@google.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Tom Herbert <therbert@google.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
netpoll can call functions in hard irq context that are ordinarily
called in lesser contexts. For those functions use dev_kfree_skb_any
and dev_consume_skb_any so skbs are freed safely from hard irq
context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace free_skb with dev_kfree_skb_any in be_tx_compl_process as
which can be called in hard irq by netpoll, softirq context
by normal napi polling, and in normal sleepable context
by the network device close method.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kfree_skb with dev_kfree_skb_any in cp_start_xmit
as it can be called in both hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VLAN is added by user, adapter->vlans_added is incremented.
But if the VLAN is already programmed in HW, driver ends up
incrementing the counter wrongly.
Increment the counter only if VLAN is not already programmed in the HW.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the driver creates only a single TXQ on any BE3-R multi-channel
interface.
This patch changes this and creates multiple TXQs on RSS-capable multi-channel
BE3-R interfaces. This change helps improve the TX pps performance on the
affected interface.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The allocation size must be be_max_uc() and not "be_max_uc() + 1"
Signed-off-by: Ravikumar Nelavelli <ravikumar.nelavelli@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ravikumar Nelavelli <ravikumar.nelavelli@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to control VF's link state by implementing the
ndo_set_vf_link_state() hook.
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use GET_PROFILE_CONFIG_V1 cmd even for BE3-R (it's already used for
Lancer-R and Skyhawk-R), to query max-vfs value supported by the FW.
This is needed as on some configs, the value exported in the PCI-config
space is not accurate.
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When checking what protocol drivers to load, the IB driver should be
requested also over Ethernet ports, if the device supports IBoE (RoCE).
Fixes: b046ffe 'net/mlx4_core: Load higher level modules according to ports type'
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device mac address is changed, we must deregister the vxlan
steering rule associated with the previous mac, and register a new
steering rule using the new mac.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the value used to dump the vxlan offloads device capability to align
with the MLX4_DEV_CAP_FLAG2_yyy definition. While on that, add dump to
the IPoIB flow-steering device capability and fix small typo.
The vxlan cap value wasn't fully handled when a conflict was resolved
between MLX4_DEV_CAP_FLAG2_DMFS_IPOIB coming from the IB tree to
MLX4_DEV_CAP_FLAG2_VXLAN_OFFLOADS coming from net-next.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To activate RoCE/SRIOV, need to remove the following:
1. In mlx4_ib_add, need to remove the error return preventing
initialization of a RoCE port under SRIOV.
2. In update_vport_qp_params (in resource_tracker.c) need to remove
the error return when a RoCE RC or UD qp is detected.
This error return causes the INIT-to-RTR qp transition to fail
in the wrapper function under RoCE/SRIOV.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since there is no connection between the MAC/VLAN and the GID
when using IP-based addressing, the proxy QP1 (running on the
slave) must pass the source-mac, destination-mac, and vlan_id
information separately from the GID. Additionally, the Host
must pass the remote source-mac and vlan_id back to the slave,
This is achieved as follows:
Outgoing MADs:
1. Source MAC: obtained from the CQ completion structure
(struct ib_wc, smac field).
2. Destination MAC: obtained from the tunnel header
3. vlan_id: obtained from the tunnel header.
Incoming MADs
1. The source (i.e., remote) MAC and vlan_id are passed in
the tunnel header to the proxy QP1.
VST mode support:
For outgoing MADs, the vlan_id obtained from the header is
discarded, and the vlan_id specified by the Hypervisor is used
instead.
For incoming MADs, the incoming vlan_id (in the wc) is discarded, and the
"invalid" vlan (0xffff) is substituted when forwarding to the slave.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IB side of RoCE requires the MAC table index of the
MAC address used by its QPs.
To obtain the real MAC index, the IB side registers the
MAC (increasing its ref count, and also returning the
real MAC index) during the modify-qp sequence.
This protects against the ETH side deleting or modifying
that MAC table entry while the QP is active.
Note that until the modify-qp command returns success,
the MAC and VLAN information only has "candidate" status.
If the modify-qp succeeds, the "candidate" info is promoted
to the operational MAC/VLAN info for the qp. If the modify fails,
the candidate MAC/VLAN is unregistered, and the old qp info
is preserved.
The patch is a bit complex, because there are multiple qp
transitions where the primary-path information may be
modified: INIT-to-RTR, and SQD-to-SQD.
Similarly for the alternate path information.
Therefore the code must handle cases where path information
has already been entered into the QP context by previous
qp transitions.
For the MAC address, the success logic is as follows:
1. If there was no previous MAC, simply move the candidate
MAC information to the operational information, and reset
the candidate MAC info.
2. If there was a previous MAC, unregister it. Then move
the MAC information from candidate to operational, and
reset the candidate info (as in 1. above).
The MAC address failure logic is the same for all cases:
- Unregister the candidate MAC, and reset the candidate MAC info.
For Vlan registration, the logic is similar.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GIDs are statically distributed, as follows:
PF: gets 16 GIDs
VFs: Remaining GIDS are divided evenly between VFs activated by the driver.
If the division is not even, lower-numbered VFs get an extra GID.
For an IB interface, the number of gids per guest remains as before: one gid per guest.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For IB transport, the host determines the slave GIDs. For ETH (RoCE),
however, the slave's GID is determined by the IP address that the slave
itself assigns to the ETH device used by RoCE.
In this case, the slave must be able to write its GIDs to the HCA gid table
(at the GID indices that slave "owns").
This commit adds processing for the SET_PORT_GID_TABLE opcode modifier
for the SET_PORT command wrapper (so that slaves may modify their GIDS
for RoCE).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This requires the following modifications:
1. Fix build_mlx4_header to properly fill in the ETH fields
2. Adjust mux and demux QP1 flow to support RoCE.
This commit still assumes only one GID per slave for RoCE.
The commit enabling multiple GIDs is a subsequent commit, and
is done separately because of its complexity.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
priv is not instantiated at gfar_of_init() time, when
parsing the DT for info on supported HW queues. Before
the netdev can be allocated, the number of supported
queues must be known. Because the number of supported
queues depends on device type, move the compatibility
checks before netdev allocation. Local vars are used
to hold the operation mode info before netdev allocation.
This fixes the null accesses for priv->.., in gfar_of_init.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx descriptor version of RTL8111B belong to RTL_TD_0.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to fix the compatibility to the STiD127 SoC.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix the chain mode that was broken
and generated a panic. This patch reviews the chain/ring
modes now shaing the same structure and taking care
about the pointers and callbacks.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix and tune the default buffer sizes.
It reduces the default bufsize used by the driver from
4KiB to 1536 bytes.
Patch has been tested on both ARM and SH4 platform based.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to disable the EEE (so HW and timers)
for example when the phy communicates that the EEE
can be supported anymore.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using an own copy of struct net_device_stats in struct
cpsw_priv, use stats from struct net_device. Also remove the thus
unnecessary .ndo_get_stats function, as it just returns dev->stats,
which is the default.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
udelay() does not work on some architectures for values above
2000, in particular on ARM:
ERROR: "__bad_udelay" [drivers/net/ethernet/brocade/bna/bna.ko] undefined!
Reported-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver reads the mac address from the device registers which would
need to have been programmed by the bootloader. This patch adds
the ability to pull the mac from devicetree via the pci device dt node.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Cc: netdev@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Changes since v2:
- eliminated use of stack tmpaddr per feedback
Changes since v1:
- simplified based on feedback
- fixed formatting
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to mlx5_health_cleanup() in the module init function can never
be reached. Removing it.
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Acked-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Faster than memcpy/memset on some architectures.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the "fsl,etsec2" compatible models the driver currently
supports 8 Tx and Rx DMA rings (aka HW queues). However, there
are only 2 pairs of Rx/Tx interrupt lines, as these controllers
are integrated in low power SoCs with 2 CPUs at most. As a result,
there are at most 2 NAPI instances that have to service multiple
Tx and Rx queues for these devices. This complicates the NAPI
polling routine having to iterate over the mutiple Rx/Tx queues
hooked to the same interrupt lines. And there's also an overhead
at HW level, as the controller needs to service all the 8 Tx rings
in a round robin manner. The combined overhead shows up for multi
parallel Tx flows transmitted by the kernel stack, when the driver
usually starts returning NETDEV_TX_BUSY leading to NETDEV WATCHDOG
Tx timeout triggering if the Tx path is congested for too long.
As an alternative, this patch makes the driver support only one
Tx/Rx DMA ring per NAPI instance (per interrupt group or pair
of Tx/Rx interrupt lines) by default. The simplified single queue
polling routine (gfar_poll_sq) will be the default napi poll routine
for the etsec2 devices too. Some adjustments needed to be made to
link the Tx/Rx HW queues with each NAPI instance (2 in this case).
The gfar_poll_sq() is already successfully used by older SQ_SG_MODE
(single interrupt group) controllers.
This patch fixes Tx timeout triggering under heavy Tx traffic load
(i.e. iperf -c -P 8) for the "fsl,etsec2" (currently the only
MQ_MG_MODE devices). There's also a significant memory footprint
reduction by supporting 2 Rx/Tx DMA rings (at most), instead of 8,
for these devices.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some concurrency issues on devices w/ 2 CPUs related
to the handling of Rx and Tx interrupts. eTSEC has separate
interrupt lines for Rx and Tx but a single imask register
to mask these interrupts and a single NAPI instance to handle
both Rx and Tx work. As a result, the Rx and Tx ISRs are
identical, both are invoking gfar_schedule_cleanup(), however
both handlers can be entered at the same time when the Rx and
Tx interrupts are taken by different CPUs. In this case
spurrious interrupts (SPU) show up (in /proc/interrupts)
indicating a concurrency issue. Also, Tx overruns followed
by Tx timeout have been observed under heavy Tx traffic load.
To address these issues, the schedule cleanup ISR part has
been changed to handle the Rx and Tx interrupts independently.
The patch adds a separate NAPI poll routine for Tx cleanup to
be triggerred independently by the Tx confirmation interrupts
only. Existing poll functions are modified to handle only
the Rx path processing. The Tx poll routine does not need a
budget, since Tx processing doesn't consume NAPI budget, and
hence it is registered with minimum NAPI weight.
NAPI scheduling does not require locking since there are
different NAPI instances between the Rx and Tx confirmation
paths now.
So, the patch fixes the occurence of spurrious Rx/Tx interrupts.
Tx overruns also occur less frequently now.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pci shutdown handler added in:
bnx2: Add pci shutdown handler
commit 25bfb1dd4b
created a shutdown down sequence without chip reset if the device was
never brought up. This can cause the firmware to shutdown the PHY
prematurely and cause MMIO read cycles to be unresponsive. On some
systems, it may generate NMI in the bnx2's pci shutdown handler.
The fix is to tell the firmware not to shutdown the PHY if there was
no prior chip reset.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix warning about code defined but never used if IGB_HWMON not defined.
Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use ARRAY_SIZE for array size calculation.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
skb->pkt_type is not a bitmask, but contains only value at a time from
the range defined in include/uapi/linux/if_packet.h.
Checking it like if it was a bitmask of values would also cause
PACKET_OTHERHOST, PACKET_LOOPBACK and PACKET_FASTROUTE to be matched by
this check since their lower 2 bits are also set, although that does not
fix a real bug, it is still potentially confusing.
This bogus check was introduced in commit 815cccbf ("ixgbe: add setlink,
getlink support to ixgbe and ixgbevf").
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previous commit c3a0dce35a fixed an overrun for the RAR on i218 devices.
This commit also attempted to homogenize the RAR/SHRA access for all parts
accessed by the e1000e driver. This change introduced an error for
assigning MAC addresses to guest OS's for 82579 devices.
Only RAR[0] is accessible to the driver for 82579 parts, and additional
addresses must be placed into the SHRA[L|H] registers. The rar_entry_count
was changed in the previous commit to an inaccurate value that accounted
for all RAR and SHRA registers, not just the ones usable by the driver.
This patch fixes the count to the correct value and adjusts the
e1000_rar_set_pch2lan() function to user the correct index.
Cc: John Greene <jogreene@redhat.com>
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Changes to the rar_entry_count value require a change to the indexing
used to access the SHRA[H|L] registers when testing them with
'ethtool -t <iface> offline'
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Valid values for InterruptThrottleRate are 10-100000, or one of
0, 1, 3, 4. '2' is not valid. This is a legacy from the branching
from the e1000 driver code that e1000e was based from.
Prior to this patch, if the e1000e driver was loaded with a forced
invalid InterruptThrottleRate of '2', then no throttle rate would be
set and no error message generated.
Now, a message will be generated that an invalid value was used and the
value for InterruptThrottleRate will be set to the default value.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ULP is a power saving feature that reduces the power consumption of the
PHY when a cable is not connected.
ULP is gated on the following conditions:
1) The hardware must support ULP. Currently this is only I218
devices from Intel
2) ULP is initiated by the driver, so, no driver results in no ULP.
3) ULP's implementation utilizes Runtime Power Management to toggle its
execution. ULP is enabled/disabled based on the state of Runtime PM.
4) ULP is not active when wake-on-unicast, multicast or broadcast is active
as these features are mutually-exclusive.
Since the PHY is in an unavailable state while ULP is active, any access
of the PHY registers will fail. This is resolved by utilizing kernel
calls that cause the device to exit Runtime PM (e.g. pm_runtime_get_sync)
and then, after PHY access is complete, allow the device to resume
Runtime PM (e.g. pm_runtime_put_sync).
Under certain conditions, toggling the LANPHYPC is necessary to disable
ULP mode. Break out existing code to toggle LANPHYPC to a new function
to avoid code duplication.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix issues with:
RuntimePM causing the device to repeatedly flip between suspend and resume
with the interface administratively downed.
Having RuntimePM enabled interfering with the functionality of Energy
Efficient Ethernet.
Added checks to disallow functions that should not be executed if the
device is currently runtime suspended
Make runtime_idle callback to use same deterministic behavior as the igb
driver.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Refactor the system power management flows to prevent the suspend path from
being executed twice when hibernating since both the freeze and
poweroff callbacks were set to e1000_suspend() via SET_SYSTEM_SLEEP_PM_OPS.
There are HW workarounds that are performed during this flow and calling
them twice was causing erroneous behavior.
Re-arrange the code to take advantage of common code paths and explicitly
set the individual dev_pm_ops callbacks for suspend, resume, freeze,
thaw, poweroff and restore.
Add a boolean parameter (reset) to the e1000e_down function to allow
for cases when the HW should not be reset when downed during a PM event.
Now that all suspend/shutdown paths result in a call to __e1000_shutdown()
that checks Wake on Lan status, removing redundant check for WoL in
e1000_power_down_phy().
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Branding strings from recently released and soon to be released
hardware configurations that are supported by e1000e.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is to update the GPL header by removing the portion that
refers to the Free Software Foundation address.
Change the copyright date for 2014.
Reformat the header comments to conform to kernel networking coding norms
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enabling EEE LPI sooner than one second after link up on 82579 causes link
issues with some switches.
Remove EEE enablement for 82579 parts from the link initialization flow to
avoid initializing too early. EEE initialization for 82579 will be done
in e1000e_update_phy_task.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce W Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On a ME enabled system with the cable out, the driver init flow would
generate an erroneous message indicating that resets were being blocked
by an active ME session. Cause was ME clearing the semaphore bit to
block further PHY resets for up to 50 msec during power-on/cycle. After
this interval, ME would re-set the bit and allow PHY resets.
To resolve this, change the flow of e1000e_phy_hw_reset_generic() to
utilize a delay and retry method. Poll the FWSM register to minimize
any extra time added to the flow. If the delay times out at 100ms
(checked in 10msec increments), then return the value E1000_BLK_PHY_RESET,
as this is the accurate state of the PHY. Attempting to alter just the
call to e1000e_phy_hw_reset_generic() in e1000_init_phy_workarounds_pchlan()
just caused the problem to move further down the flow.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce W. Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cleaning up some pointer references that are no longer necessary
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add lock in e1000e_phc_adjfreq to prevent concurrent changes to TIMINCA
and SYSTIMH/L.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This will be useful when processing signature errors on a specific
key. The mlx5 driver will lookup the matching mlx5 memory region
structure and mark it as dirty (contains signature errors).
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Support create_mr and destroy_mr verbs. Creating ib_mr may be done
for either ib_mr that will register regular page lists like
alloc_fast_reg_mr routine, or indirect ib_mrs that can register other
(pre-registered) ib_mrs in an indirect manner.
In addition user may request signature enable, that will mean that the
created ib_mr may be attached with signature attributes (BSF, PSVs).
Currently we only allow direct/indirect registration modes.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
We need to make sure that we stay away from the cache line
where the DD bit (done) may be getting written back for
the transmit ring since the hardware may be writing the
whole cache line for a partial update.
Change-ID: Id0b6dfc01f654def6a2a021af185803be1915d7e
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver needs to use the format that the current NVM
uses when printing the version of the NVM. It should remain
this way from now on forward.
The driver was reporting when firmware was less than
an expected version number, but this is not a requirement
for the product and we print the firmware number at
init and in ethtool -i output. Just remove the print.
Change-ID: Ide0b856cd454ebf867610ef9a0d639bb358a4a60
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the following static checker warning:
drivers/net/ethernet/intel/i40e/i40e_dcb.c:342
i40e_lldp_to_dcb_config() warn: 'tlv' can't be NULL.
Exit criteria from the while loop is encountering LLDP END
LV or if the TLV length goes beyond the buffer length.
Change-ID: I7548b16db90230ec2ba0fa791b0343ca8b7dd5bb
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Tested-By: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ethtool -S statistics should have a counter for
tx timeouts in order to better help inform the masses.
Change-ID: Ice4b20ed4a151509f366719ab105be49c9e7b2b4
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Number of MSIX vectors being reported is correct and hence
we need a check to do the right thing for FWs before and after.
Change-ID: I50902d1c848adcb960ea49ac73f7865ca871a1c3
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Lots of trivial changes to remove double spaces in function headers,
unnecessary periods in short comments, and adjust the English usage here
and there.
No actual code was harmed in the making of this patch.
Change-ID: I6e756c500756945e81a61ffb10221753eb7923ea
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Original comment from Tom Herbert <therbert@google.com>
Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
This patch builds upon Tom's original implementation and adds
the L4 type return when we know it is an L4 hash.
This requires use of the ptype decoder ring, so enable it.
Change-ID: I2f9fa86d1a6add58cff13386f7f4238b1abcc468
CC: Tom Herbert <therbert@google.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To prevent the possibility of overflow due multiplication of number and size
use kcalloc instead of kzalloc.
Change-ID: Ibe4d81ed7d9738d3bbe66ee4844ff9be817e8080
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set netdev->hw_features to enable the ndo_set_features netdev op.
Change-Id: I5a086fbfa5a089de5adba2800c4d0b3a73747b11
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, the PF call to pci_enable_sriov from the PF probe function
stalls for 10 seconds times the number of VFs probed on the host. This
happens because the way for such VFs to determine of the PF
initialization finished, is by attempting to issue reset on the
comm-channel and get timeout (after 10s).
The PF probe function is called from a kenernel workqueue, and therefore
during that time, rcu lock is being held and kernel's workqueue is
stalled. This blocks other processes that try to use the workqueue
or rcu lock. For example, interface renaming which is calling
rcu_synchronize is blocked, and timedout by systemd.
Changed mlx4_init_slave() to allow VF probed on the host to immediatly
detect that the PF is not ready, and return EPROBE_DEFER instantly.
Only when the PF finishes the initialization, allow such VFs to
access the comm channel.
This issue and fix are relevant only for probed VFs on the hypervisor,
there is no way to pass this information to a VM until comm channel is
ready, so in a VM, if PF is not ready, the first command will be timedout
after 10 seconds and return EPROBE_DEFER.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a regression introduced by [1]. outbox was accessed instead of
outbox->buf. Typo was copy-pasted to [2] and [3].
[1] - cc1ade9 mlx4_core: Disable memory windows for virtual functions
[2] - 4de6580 mlx4_core: Add support for steerable IB UD QPs
[3] - 7ffdf72 net/mlx4_core: Add basic support for TCP/IP offloads under
tunneling
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix static error introduced by commit:
b97b33a3df [645/653] net/mlx4_en: Verify
mlx4_en module parameters
sparse warnings:
drivers/net/ethernet/mellanox/mlx4/en_main.c:335:6: sparse: symbol
'mlx4_en_verify_params' was not declared. Should it be static?
CC: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org
CC: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code to load a MAC address into a u64 for passing to the
hypervisor via a register is broken on little endian.
Create a helper function called ibmveth_encode_mac_addr
which does the right thing in both big and little endian.
We were storing the MAC address in a long in struct ibmveth_adapter.
It's never used so remove it - we don't need another place in the
driver where we create endian issues with MAC addresses.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
When allocating RX buffers a fixed size is used, while freeing is based
on actually received bytes, resulting in the following kernel warning
when CONFIG_DMA_API_DEBUG is enabled:
WARNING: CPU: 0 PID: 0 at lib/dma-debug.c:1051 check_unmap+0x258/0x894()
macb e000b000.ethernet: DMA-API: device driver frees DMA memory with different size [device address=0x000000002d170040] [map size=1536 bytes] [unmap size=60 bytes]
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.14.0-rc3-xilinx-00220-g49f84081ce4f #65
[<c001516c>] (unwind_backtrace) from [<c0011df8>] (show_stack+0x10/0x14)
[<c0011df8>] (show_stack) from [<c03c775c>] (dump_stack+0x7c/0xc8)
[<c03c775c>] (dump_stack) from [<c00245cc>] (warn_slowpath_common+0x60/0x84)
[<c00245cc>] (warn_slowpath_common) from [<c0024670>] (warn_slowpath_fmt+0x2c/0x3c)
[<c0024670>] (warn_slowpath_fmt) from [<c0227d44>] (check_unmap+0x258/0x894)
[<c0227d44>] (check_unmap) from [<c0228588>] (debug_dma_unmap_page+0x64/0x70)
[<c0228588>] (debug_dma_unmap_page) from [<c02ab78c>] (gem_rx+0x118/0x170)
[<c02ab78c>] (gem_rx) from [<c02ac4d4>] (macb_poll+0x24/0x94)
[<c02ac4d4>] (macb_poll) from [<c031222c>] (net_rx_action+0x6c/0x188)
[<c031222c>] (net_rx_action) from [<c0028a28>] (__do_softirq+0x108/0x280)
[<c0028a28>] (__do_softirq) from [<c0028e8c>] (irq_exit+0x84/0xf8)
[<c0028e8c>] (irq_exit) from [<c000f360>] (handle_IRQ+0x68/0x8c)
[<c000f360>] (handle_IRQ) from [<c0008528>] (gic_handle_irq+0x3c/0x60)
[<c0008528>] (gic_handle_irq) from [<c0012904>] (__irq_svc+0x44/0x78)
Exception stack(0xc056df20 to 0xc056df68)
df20: 00000001 c0577430 00000000 c0577430 04ce8e0d 00000002 edfce238 00000000
df40: 04e20f78 00000002 c05981f4 00000000 00000008 c056df68 c0064008 c02d7658
df60: 20000013 ffffffff
[<c0012904>] (__irq_svc) from [<c02d7658>] (cpuidle_enter_state+0x54/0xf8)
[<c02d7658>] (cpuidle_enter_state) from [<c02d77dc>] (cpuidle_idle_call+0xe0/0x138)
[<c02d77dc>] (cpuidle_idle_call) from [<c000f660>] (arch_cpu_idle+0x8/0x3c)
[<c000f660>] (arch_cpu_idle) from [<c006bec4>] (cpu_startup_entry+0xbc/0x124)
[<c006bec4>] (cpu_startup_entry) from [<c053daec>] (start_kernel+0x350/0x3b0)
---[ end trace d5fdc38641bd3a11 ]---
Mapped at:
[<c0227184>] debug_dma_map_page+0x48/0x11c
[<c02ab32c>] gem_rx_refill+0x154/0x1f8
[<c02ac7b4>] macb_open+0x270/0x3e0
[<c03152e0>] __dev_open+0x7c/0xfc
[<c031554c>] __dev_change_flags+0x8c/0x140
Fixing this by passing the same size which is passed during mapping the
memory to the unmap function as well.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In kexec scenario, we failed to load the mlx4 driver in the
second kernel because the ownership bit was hold by the first
kernel without release correctly.
The patch adds shutdown() interface so that the ownership can
be released correctly in the first kernel. It also helps avoiding
EEH error happened during boot stage of the second kernel because
of undesired traffic, which can't be handled by hardware during
that stage on Power platform.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Tested-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/mwifiex/pcie.c
net/ipv6/sit.c
The SIT driver conflict consists of a bug fix being done by hand
in 'net' (missing u64_stats_init()) whilst in 'net-next' a helper
was created (netdev_alloc_pcpu_stats()) which takes care of this.
The two wireless conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently maps a page for DMA, divides the page into multiple
frags and posts them to the HW. It un-maps the page after data is received
on all the frags of the page. This scheme doesn't work when bounce buffers
are used for DMA (swiotlb=force kernel param).
This patch fixes this problem by calling dma_sync_single_for_cpu() for each
frag (excepting the last one) so that the data is copied from the bounce
buffers. The page is un-mapped only when DMA finishes on the last frag of
the page.
(Thanks Ben H. for suggesting the dma_sync API!)
This patch also renames the "last_page_user" field of be_rx_page_info{}
struct to "last_frag" to improve readability of the fixed code.
Reported-by: Li Fengmao <li.fengmao@zte.com.cn>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a CPDMA RX Descriptor leak that occurs after taking
the interface down when the CPSW is in Dual MAC mode. Previously
the CPSW_ALE port was left open up which causes packets to be received
and processed by the RX interrupt handler and were passed to the
non active network interface where they were ignored.
The fix is for the slave_stop function of the selected interface
to disable the respective CPSW_ALE Port from forwarding packets. This
blocks traffic from being received on the inactive interface.
Signed-off-by: Schuyler Patton <spatton@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of TX workarounds in be_xmit_workarounds() routine
are not applicable (and result in HW errors) to Skyhawk-R chip.
Isolate BE3-R/Lancer specific workarounds to a separate routine.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_padto(), skb_share_check() and __vlan_put_tag() routines free
skb when they return an error. This patch fixes be_xmit_workarounds()
to not free skb again in such cases.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should clear promiscuous bits in adapter->flags while disabling promiscuous
mode. Else we will not put interface back into VLAN promisc mode if the vlans
already added exceeds the maximum limit.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For disabling transparent tagging issue SET_HSW_CONFIG with pvid_valid=1
and pvid=0xFFFF and not with the default pvid as this case would fail in Lancer.
Hence removing the get_hsw_config call from be_vf_setup() as it's
only use of getting default pvid is no longer needed.
Also do proper housekeeping only if the FW command succeeds.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ->tc_cfg[] array has QLC_DCB_MAX_TC (8) elements so the check is
off by one. These functions are always called with valid values though
so it doesn't affect how the code works.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlx4_en driver support also 1Gbit and 40Gbit Ethernet devices,
changed the driver description in the menuconfig to reflect that.
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When BlueFlame is turned on, control segment of the TX WQE is changed,
and the second line of it is used for QPN.
Changed code to use a union in the mlx4_wqe_ctrl_seg instead of casting.
This makes the code clearer and solves the static checker warning:
drivers/net/ethernet/mellanox/mlx4/en_tx.c:839 mlx4_en_xmit()
warn: potential memory corrupting cast 4 vs 2 bytes
CC: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch force conversion to u32 to fix the following sparse warning:
drivers/net/ethernet/mellanox/mlx4/fw.c:1822:53: warning: restricted __be32
degrades to integer
Casting to u32 is safe here, because token will be returned as is
from the hardware without any modification.
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Connect-X devices selftest speed test shouldn't fail on 1G and 40G link
speeds.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the EN driver uses a private static function
mlx4_en_mac_to_u64(). Move it to a common include file (driver.h)
for mlx4_en and mlx4_ib for further use.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Give accurate counters and avoids cache misses when several rings
update the counters of stop/wake queue.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware can't accept packets smaller than 17 bytes. Therefore need to
pad with zeros.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify mlx4_en module parameters.
In case they are out of range - reset to default values.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
User priority limit has to be less than MLX4_EN_NUM_UP.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the new SIOCGHWTSTAMP ioctl, which enables a
process to determine the current timestamp configuration. In order to
implement this, store a copy of the timestamp configuration. In
addition, we can remove the 'int cmd' parameter as the new set_ts_config
function doesn't use it. I also fixed a typo in the function
description.
-v2
* Only save the settings after validating them
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuration space reads should also be checked for removal. So
add some checks related to config space accesses.
v2:
* Fixed indent
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ethtool tests returned apparently good results when the
adapter was in a removed state. Fix that by checking for removal.
This also fixes two paths that could return uninitialized memory
in data[4].
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hw_addr needs to be restored in the pcie recovery path or
else the device will be perpetually removed. Also restore the
value in the resume path.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch b44_check_phy() was called when the phy called the
adjust callback. This method only change the mac duplex mode when the
carrier was off. When the phy changed the duplex mode after the carrier
was on the mac was not changed. This happened when an external phy was
used.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When support for external phys was added to b44, the calls to start and
stop the phy were missing in the mac driver. This adds the calls to
phy_start() and phy_stop().
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
