Commit 7ae81952cda ("i2c: i801: Allow ACPI SystemIO OpRegion to conflict
with PCI BAR") made it possible for AML code to access SMBus I/O ports
by installing custom SystemIO OpRegion handler and blocking i80i driver
access upon first AML read/write to this OpRegion.
However, while ThinkPad T560 does have SystemIO OpRegion declared under
the SMBus device, it does not access any of the SMBus registers:
Device (SMBU)
{
...
OperationRegion (SMBP, PCI_Config, 0x50, 0x04)
Field (SMBP, DWordAcc, NoLock, Preserve)
{
, 5,
TCOB, 11,
Offset (0x04)
}
Name (TCBV, 0x00)
Method (TCBS, 0, NotSerialized)
{
If ((TCBV == 0x00))
{
TCBV = (\_SB.PCI0.SMBU.TCOB << 0x05)
}
Return (TCBV) /* \_SB_.PCI0.SMBU.TCBV */
}
OperationRegion (TCBA, SystemIO, TCBS (), 0x10)
Field (TCBA, ByteAcc, NoLock, Preserve)
{
Offset (0x04),
, 9,
CPSC, 1
}
}
Problem with the current approach is that it blocks all I/O port access
and because this system has touchpad connected to the SMBus controller
after first AML access (happens during suspend/resume cycle) the
touchpad fails to work anymore.
Fix this so that we allow ACPI AML I/O port access if it does not touch
the region reserved for the SMBus.
Fixes: 7ae81952cda ("i2c: i801: Allow ACPI SystemIO OpRegion to conflict with PCI BAR")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200737
Reported-by: Yussuf Khalil <dev@pp3345.net>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The old @sunsite.dk address is no longer active, so update the references.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
- the core has now a lockless variant of i2c_smbus_xfer. Some open
coded versions of this got removed in drivers. This also enables
proper SCCB support in regmap.
- locking got a more precise naming. i2c_{un}lock_adapter() had to go,
and we know use i2c_lock_bus() consistently with flags like
I2C_LOCK_ROOT_ADAPTER and I2C_LOCK_SEGMENT to avoid ambiguity.
- the gpio fault injector got a new delicate testcase
- the bus recovery procedure got fixed to handle the new testcase
correctly
- a new quirk flag for controllers not able to handle zero length
messages together with driver updates to use it
- new drivers: FSI bus attached I2C masters, GENI I2C controller, Owl
family S900
- and a good set of driver improvements and bugfixes
* 'i2c/for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (77 commits)
i2c: rcar: implement STOP and REP_START according to docs
i2c: rcar: refactor private flags
i2c: core: ACPI: Make acpi_gsb_i2c_read_bytes() check i2c_transfer return value
i2c: core: ACPI: Properly set status byte to 0 for multi-byte writes
dt-bindings: i2c: rcar: Add r8a774a1 support
dt-bindings: i2c: sh_mobile: Add r8a774a1 support
i2c: imx: Simplify stopped state tracking
i2c: imx: Fix race condition in dma read
i2c: pasemi: remove hardcoded bus numbers on smbus
i2c: designware: Add SPDX license tag
i2c: designware: Convert to use struct i2c_timings
i2c: core: Parse SDA hold time from firmware
i2c: designware-pcidrv: Mark expected switch fall-through
i2c: amd8111: Mark expected switch fall-through
i2c: sh_mobile: use core to detect 'no zero length read' quirk
i2c: xlr: use core to detect 'no zero length' quirk
i2c: rcar: use core to detect 'no zero length' quirk
i2c: stu300: use core to detect 'no zero length' quirk
i2c: pmcmsp: use core to detect 'no zero length' quirk
i2c: mxs: use core to detect 'no zero length' quirk
...
When doing a REP_START after a read message, the driver used to trigger
a STOP first which would then be overwritten by REP_START. This was the
only stable method found when doing the last refactoring. However, this
was not in accordance with the documentation.
After research from our BSP team and myself, we now can implement a
version which works and is according to the documentation. The new
approach ensures the ICMCR register is only changed when really needed.
Tested on a R-Car Gen2 (H2) and Gen3 with DMA (M3N).
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use BIT macro to avoid shift-31-problem, indent a little more and use
GENMASK to make it easier to add new flags.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Always update the stopped state when busy status have been checked.
This is identical to what was done before, with the exception of error
handling.
Without this change, some errors cause the stopped state to be left in
incorrect state in i2c_imx_stop(), i2c_imx_dma_read(), i2c_imx_read() and
i2c_imx_xfer().
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This fixes a race condition, where the DMAEN bit ends up being set after
I2C slave has transmitted a byte following the dummy read. When that
happens, an interrupt is generated instead, and no DMA request is generated
to kickstart the DMA read, and a timeout happens after DMA_TIMEOUT (1 sec).
Fixed by setting the DMAEN bit before the dummy read.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
The pasemi smbus controller uses PCI_FUNC(dev->devfn) to define which
number bus to attach to, however this fails when something else is
probed first, for example an ATI Radeon graphics card will claim 9 or
10 busses, including the ones the pasemi wants.
Patch the driver to call i2c_add_adapter rather than
i2c_add_numbered_adapter.
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Replace short statement in comment with proper SPDX license tag.
Note, for i2c-desingware-slave.c the identifier is chosen
in accordance with MODULE_LICENSE() macro since it is visible to user.
Another point to this choice is that the header seems to be copy'n'paste
from the other file of this very driver.
Acked-by: Luis Oliveira <Luis.Oliveira@synopsys.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
During ipmi stress tests we see occasional failure of transactions
at the boot time. This happens in the case of a I2C_M_RECV_LEN
transactions, when the read transfer completes (with the initial
read length of 34) before the driver gets a chance to handle interrupts.
The current driver code expects at least 2 interrupts for I2C_M_RECV_LEN
transactions. The length is updated during the first interrupt, and the
buffer contents are only copied during subsequent interrupts. In case of
just one interrupt, we will complete the transaction without copying
out the bytes from RX fifo.
Update the code to drain the RX fifo after the length update,
so that the transaction completes correctly in all cases.
Signed-off-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Instead of using custom variables and parser, convert the driver to use
the ones provided by I2C core.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
And don't reimplement in the driver.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
And don't reimplement in the driver.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
And don't reimplement in the driver.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
And don't reimplement in the driver.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This bus driver supports the GENI based i2c hardware controller in the
Qualcomm SOCs. The Qualcomm Generic Interface (GENI) is a programmable
module supporting a wide range of serial interfaces including I2C. The
driver supports FIFO mode and DMA mode of transfer and switches modes
dynamically depending on the size of the transfer.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Signed-off-by: Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
[wsa: squashed the MAINTAINER addition and a RPM fix by Evan Green]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C is open drain, so request the GPIO accordingly, even if pinmux did
set it up correctly for in-kernel users in this case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On Gen3, we can only do RXDMA once per transfer reliably. For that, we
must reset the device, then we can have RXDMA once. This patch
implements this. When there is no reset controller or the reset fails,
RXDMA will be blocked completely. Otherwise, it will be disabled after
the first RXDMA transfer. Based on a commit from the BSP by Hiromitsu
Yamasaki, yet completely refactored to handle multiple read messages
within one transfer.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
On Gen3, we can only do RXDMA once per transfer reliably. For that, we
must reset the device, then we can have RXDMA once. This patch
implements this. When there is no reset controller or the reset fails,
RXDMA will be blocked completely. Otherwise, it will be disabled after
the first RXDMA transfer. Based on a commit from the BSP by Hiromitsu
Yamasaki, yet completely refactored to handle multiple read messages
within one transfer.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make sure to call reinit_completion() before dma is started to avoid race
condition where reinit_completion() is called after complete() and before
wait_for_completion_timeout().
Signed-off-by: Esben Haabendal <eha@deif.com>
Fixes: ce1a78840f ("i2c: imx: add DMA support for freescale i2c driver")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
If CLKH is set to 0 I2C clock is not generated at all, so avoid this value
and stretch the clock in this case.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adjusts spinlock scope to make it wrap the whole irq
handler using a single lock/unlock which covers both master and
slave handlers.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch changes the order of enum aspeed_i2c_master_state and
enum aspeed_i2c_slave_state defines to make their initial value to
ASPEED_I2C_MASTER_INACTIVE and ASPEED_I2C_SLAVE_STOP respectively.
In case of multi-master use, if a slave data comes ahead of the
first master xfer, master_state starts from an invalid state so
this change fixes the issue.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There are some log printing without a newline character. This
patch adds the missing newline characters.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver supports multiple hardware variants of Exynos I2C controller
which differ in FIFO depth, handling of interrupts and bus recovery in
HSI2C_MASTER_ST_LOSE state.
The difference in variant was a single bit set for Exynos7 variants and
implicit lack of this bit for other variants.
Make each variant explicit which also fixes the GCC warning about
documentation:
drivers/i2c/busses/i2c-exynos5.c:223: warning: Function parameter or member 'hw' not described in 'exynos_hsi2c_variant'
No change in functionality.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Bus recovery should reset the bus with the standard i2c recovery
procedure. Populate the necessary fields so that the standard procedure
can perform the reset.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since there are many ports per master, each with it's own adapter and
chardev, we need some locking to prevent transfers from changing the
master state while other transfers are in progress.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Execute I2C transfers from the FSI-attached I2C master. Use polling
instead of interrupts as we have no hardware IRQ over FSI.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add abort procedure for failed transfers. Add engine reset procedure
that is executed during the abort to recover from various fault
conditions.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add and initialize I2C adapters for each port on the FSI-attached I2C
master. Ports for each master are defined in the devicetree.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add register definitions for FSI-attached I2C master and functions to
access those registers over FSI. Add an FSI driver so that our I2C bus
is probed up during an FSI scan.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
To break out of recovery as early as possible, feed back the bus_free
logic state.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c fixes from Wolfram Sang:
- I2C core bugfix regarding bus recovery
- driver bugfix for the tegra driver
- typo correction
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: recovery: if possible send STOP with recovery pulses
i2c: tegra: Fix NACK error handling
i2c: stu300: use non-archaic spelling of failes
The i2c_lock_adapter name is ambiguous since it is unclear if it
refers to the root adapter or the adapter you name in the argument.
The natural interpretation is the adapter you name in the argument,
but there are historical reasons for that not being the case; it
in fact locks the root adapter. Just remove the function and force
users to spell out the I2C_LOCK_ROOT_ADAPTER name to indicate what
is really going on. Also remove i2c_unlock_adapter, of course.
This patch was generated with
git grep -l 'i2c_\(un\)\?lock_adapter' \
| xargs sed -i 's/i2c_\(un\)\?lock_adapter(\([^)]*\))/'\
'i2c_\1lock_bus(\2, I2C_LOCK_ROOT_ADAPTER)/g'
followed by white-space touch-up.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On Tegra30 Cardhu the PCA9546 I2C mux is not ACK'ing I2C commands on
resume from suspend (which is caused by the reset signal for the I2C
mux not being configured correctl). However, this NACK is causing the
Tegra30 to hang on resuming from suspend which is not expected as we
detect NACKs and handle them. The hang observed appears to occur when
resetting the I2C controller to recover from the NACK.
Commit 77821b4678 ("i2c: tegra: proper handling of error cases") added
additional error handling for some error cases including NACK, however,
it appears that this change conflicts with an early fix by commit
f70893d083 ("i2c: tegra: Add delay before resetting the controller
after NACK"). After commit 77821b4678 was made we now disable 'packet
mode' before the delay from commit f70893d083 happens. Testing shows
that moving the delay to before disabling 'packet mode' fixes the hang
observed on Tegra30. The delay was added to give the I2C controller
chance to send a stop condition and so it makes sense to move this to
before we disable packet mode. Please note that packet mode is always
enabled for Tegra.
Fixes: 77821b4678 ("i2c: tegra: proper handling of error cases")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@vger.kernel.org
Intel Ice Lake has the same SMBus host controller than Intel Cannon
Lake. Add the PCI ID to the drivers list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[jarkko.nikula@linux.intel.com: Add entries to Documentation and Kconfig]
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make list of supported chipsets a little bit shorter by consolidating
names that belong to the same family.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In order to support advanced features, the I2C FIFO interface was
changed in the version of the Tegra I2C controller found in Tegra194.
The changes are backwards incompatible, so the driver needs to be
programmed in a slightly different way on new chips.
Add support for MST FIFO programming and add an OF match entry for
Tegra194. At the same time, mark all prior generations of this
controller as not having the MST FIFO interface.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add another injector for an incomplete transfer. As mentioned in the
docs, this one is important to check bus recovery algorithms with it.
Otherwise random data may be sent to devices!
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make the incomplete_transfer routine reusable, so we can add other test
cases with different patterns later. Prepare the docs for that, too.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Trivial added debug print for dev->clk_freq doesn't necessarily tell the
actual bus speed or mode the controller is operating. For instance it
may indicate 1 MHz Fast Mode Plus or 3.4 MHz High Speed but driver ends up
using 400 kHz Fast Mode due missing timing parameters or missing support
from HW.
Add a debug print that prints the bus speed based on the validated speed
that gets programmed into a HW.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
SDA hold time is an important timing parameter and often reason for
arbitration lost errors if not set to a correct value. Add a debug print
for it in order to see what value gets programmed to a HW.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Mixed timing parameter validation, calculation and their debug prints
with HW initialization in i2c_dw_init_master() and i2c_dw_init_slave()
as been bothering me some time.
It makes function a little bit unclear to follow, doesn't show what steps
are needed to do only once during probe and what are needed whenever HW
needs to be reinitialized. Also those debug prints show information that
doesn't change runtime and thus are also needlessly printed multiple times
whenever HW is reinitialized.
Thus let the i2c_dw_init_master() and i2c_dw_init_slave() to do only HW
initialization and move out one time parameter setting and debug prints
to separate functions which are called only during probe.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
SDA hold time configuration is common to both master and slave code. It
is also something that can be done once during probe and do only
register write when HW needs to be reinitialized.
Remove duplication and move SDA hold time configuration to common code.
It will be called from slave probe and for master code from a new
i2c_dw_set_timings_master() to where we will populate more probe time
timing parameter setting.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is rather readability update than micro-optimization, or if not
optimization at all. We take the input clock rate to a variable and pass
that to SCL timing parameter calculation functions.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It looks ___constant_swab32 is an internal byte swap detail. Switch to
swap32() and include header file for it explicitly. Now it comes
implicitly via linux/i2c.h include.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move register access detection out from master and slave HW
initialization code to common code. Motivation for this is to have
register access configured before HW initialization and remove
duplicated code.
This allows to do further separation between probe time initialization
and runtime reinitialization code.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 43df43e6ba ("i2c: designware: Don't set SCL timings and speed
mode when in slave mode") made variable comp_param1 needless in
i2c_dw_init_slave(). Remove it now.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit f2a8aa053c ("typec: tcpm: Represent source supply through
power_supply") moved the code to register a power_supply representing
the device supplying power to the type-C connector, from the fusb302
code to the generic tcpm code.
This has caused the power-supply registered by the fusb302 driver,
which determines how much current the bq24190 can draw, to change name
from "fusb302-typec-source" to "tcpm-source-psy-i2c-fusb302".
Fixes: f2a8aa053c ("typec: tcpm: Represent source supply through...")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It seems that during the conversion from gpio* to gpiod*, the initial
state of SCL was wrongly switched to LOW. Fix it to be HIGH again.
Fixes: 7bb75029ef ("i2c: gpio: Enforce open drain through gpiolib")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Pull i2c updates from Wolfram Sang:
- mainly feature additions to drivers (stm32f7, qup, xlp9xx, mlxcpld, ...)
- conversion to use the i2c_8bit_addr_from_msg macro consistently
- move includes to platform_data
- core updates to allow the (still in review) I3C subsystem to connect
- and the regular share of smaller driver updates
* 'i2c/for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (68 commits)
i2c: qup: fix building without CONFIG_ACPI
i2c: tegra: Remove suspend-resume
i2c: imx-lpi2c: Switch to SPDX identifier
i2c: mxs: Switch to SPDX identifier
i2c: busses: make use of i2c_8bit_addr_from_msg
i2c: algos: make use of i2c_8bit_addr_from_msg
i2c: rcar: document R8A77980 bindings
i2c: qup: Add command-line parameter to override SCL frequency
i2c: qup: Correct duty cycle for FM and FM+
i2c: qup: Add support for Fast Mode Plus
i2c: qup: add probe path for Centriq ACPI devices
i2c: robotfuzz-osif: drop pointless test
i2c: robotfuzz-osif: remove pointless local variable
i2c: rk3x: Don't print visible virtual mapping MMIO address
i2c: opal: don't check number of messages in the driver
i2c: ibm_iic: don't check number of messages in the driver
i2c: imx: Switch to SPDX identifier
i2c: mux: pca954x: merge calls to of_match_device and of_device_get_match_data
i2c: mux: demux-pinctrl: use proper parent device for demux adapter
i2c: mux: improve error message for failed symlink
...
Here is the big USB pull request for 4.18-rc1.
Lots of stuff here, the highlights are:
- phy driver updates and new additions
- usual set of xhci driver updates
- normal set of musb updates
- gadget driver updates and new controllers
- typec work, it's getting closer to getting fully out of the
staging portion of the tree.
- lots of minor cleanups and bugfixes.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWxba6w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykumQCg2abWE5LijR0SNJIwX8xk64HLUAMAnAxBZDG3
aB0GyOQd54L+09q4LAdn
=ZCEx
-----END PGP SIGNATURE-----
Merge tag 'usb-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and PHY updates from Greg KH:
"Here is the big USB pull request for 4.18-rc1.
Lots of stuff here, the highlights are:
- phy driver updates and new additions
- usual set of xhci driver updates
- normal set of musb updates
- gadget driver updates and new controllers
- typec work, it's getting closer to getting fully out of the staging
portion of the tree.
- lots of minor cleanups and bugfixes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
Revert "xhci: Reset Renesas uPD72020x USB controller for 32-bit DMA issue"
xhci: Add quirk to zero 64bit registers on Renesas PCIe controllers
xhci: Allow more than 32 quirks
usb: xhci: force all memory allocations to node
selftests: add test for USB over IP driver
USB: typec: fsusb302: no need to check return value of debugfs_create_dir()
USB: gadget: udc: s3c2410_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: renesas_usb3: no need to check return value of debugfs_create functions
USB: gadget: udc: pxa27x_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: gr_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: bcm63xx_udc: no need to check return value of debugfs_create functions
USB: udc: atmel_usba_udc: no need to check return value of debugfs_create functions
USB: dwc3: no need to check return value of debugfs_create functions
USB: dwc2: no need to check return value of debugfs_create functions
USB: core: no need to check return value of debugfs_create functions
USB: chipidea: no need to check return value of debugfs_create functions
USB: ehci-hcd: no need to check return value of debugfs_create functions
USB: fhci-hcd: no need to check return value of debugfs_create functions
USB: fotg210-hcd: no need to check return value of debugfs_create functions
USB: imx21-hcd: no need to check return value of debugfs_create functions
...
The added Centriq support broke compilation with CONFIG_ACPI disabled:
drivers/i2c/busses/i2c-qup.c: In function 'qup_i2c_probe':
drivers/i2c/busses/i2c-qup.c:1707:25: error: 'qup_i2c_acpi_match' undeclared (first use in this function); did you mean 'qup_i2c_recv_data'?
This fixes it by removing the extraneous #ifdef. All ACPI specific
code will be dropped implicitly when that option is disabled, but
the compiler first needs to see it.
Fixes: 902a91a02b ("i2c: qup: add probe path for Centriq ACPI devices")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Austin Christ <austinwc@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Nothing prevents I2C clients to access I2C while Tegra's driver is being
suspended, this results in -EBUSY error returned to the clients and that
may have unfortunate consequences. In particular this causes problems
for the TPS6586x MFD driver which emits hundreds of "failed to read
interrupt status" error messages on resume from suspend. This happens if
TPS6586X is used to wake system from suspend by the expired RTC alarm
timer because TPS6586X is an I2C device driver and its IRQ handler reads
the status register while Tegra's I2C driver is suspended, i.e. just after
kernel enabled IRQ's during of resume-from-suspend process.
Note that the removed tegra_i2c_resume() invoked tegra_i2c_init() which
performs HW reset. That seems was also not entirely correct because moving
tegra_i2c_resume to an earlier stage of resume-from-suspend process causes
I2C transfer to fail in the case of TPS6586X. It is fine to remove the
HW-reinitialization for now because it should be only needed in a case of
using lowest power-mode during suspend, which upstream kernel doesn't
support.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Because it looks neater.
For diolan, this allows factoring out some code that is now common
between if and else.
For eg20t, pch_i2c_writebytes is always called with a write in
msgs->flags, and pch_i2c_readbytes with a read.
For imx, i2c_imx_dma_write and i2c_imx_write are always called with a
write in msgs->flags, and i2c_imx_read with a read.
For qup, qup_i2c_write_tx_fifo_v1 is always called with a write in
qup->msg->flags.
For stu300, also restructure debug output for resends, since that
code as a result is only handling debug output.
Reviewed-by: Guenter Roeck <linux@roeck-us.net> [diolan]
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> [efm32 and imx]
Acked-by: Linus Walleij <linus.walleij@linaro.org> [stu300]
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The URL is broken. This patch fixes it.
Signed-off-by: Federico Vaga <federico.vaga@vaga.pv.it>
[wsa: shortened the URL a bit]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add a module parameter to override SCL frequency provided by firmware.
This can be useful when testing spec compliance for I2C modes or when
debugging issues across multiple operating frequencies.
Signed-off-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The I2C spec UM10204 Rev. 6 specifies the following timings.
Standard Fast Mode Fast Mode Plus
SCL low 4.7us 1.3us 0.5us
SCL high 4.0us 0.6us 0.26us
This results in a 33%/66% duty cycle as opposed to the 50%/50% duty cycle
used for Standard-mode.
Add High Time Divider settings to correct duty cycle for FM(400kHz) and
FM+(1MHz).
Signed-off-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Previously the QUP driver limited operation mode to I2C Fast Mode. Add
Fast Mode Plus functionality by raising SCL limit from 400kHz to 1MHz.
Signed-off-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for Qualcomm Centriq devices that are qup-v2 compatible but
do not support DMA, so nodma needs to be set.
Signed-off-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In the for-loop test, ret will be either 0 or 1. So, the
comparison is pointless. Drop it, and drop the initializer
which is then also pointless.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Just use the value directly instead of assigning it to a
variable first. And then drop the unused variable.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Now %p doesn't print visible pointer address unless the user
really want it. According to Documentation/core-api/printk-formats.rst,
%px should be used instead, otherwise we could see:
rk3x-i2c ff110000.i2c: Initialized RK3xxx I2C bus at (____ptrval____)
rk3x-i2c ff130000.i2c: Initialized RK3xxx I2C bus at (____ptrval____)
rk3x-i2c ff3c0000.i2c: Initialized RK3xxx I2C bus at (____ptrval____)
rk3x-i2c ff3d0000.i2c: Initialized RK3xxx I2C bus at (____ptrval____)
But I don't really understand why we need dump it in the first place!
Let's remove the whole pointless log.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since commit 1eace8344c ("i2c: add param sanity check to
i2c_transfer()") and b7f6258402 ("i2c: add quirk checks to core"), the
I2C core does this check now. We can remove it here.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Peter Rosin <peda@axentia.se>
Since commit 1eace8344c ("i2c: add param sanity check to
i2c_transfer()"), the I2C core does this check now. We can remove it
from drivers.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Peter Rosin <peda@axentia.se>
The driver will not probe unless bq24190 is loaded, so
making it a dependency.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For SMBus transactions the max permissible transfer size is
I2C_SMBUS_BLOCK_SIZE. It is possible that some clients might
not follow it strictly occasionally.
This would lead to stack corruption if the driver copies more than
I2C_SMBUS_BLOCK_SIZE bytes. Add a check to avoid such conditions.
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Signed-off-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The hardware does not handle updates to the length register gracefully
if the new value is less than the number of bytes received so far. If
this happens, the i2c controller will not stop the receive transaction
properly.
Fix this by ensuring that the updated length is ok. This is done by
making sure that the new length written to hardware is at least few
bytes more than the bytes received so far.
While at that refactor the length updation to a new function.
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Signed-off-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for SMBus alert mechanism to i2c-xlp9xx driver.
The second interrupt is parsed to use for SMBus alert.
The first interrupt is the i2c controller main interrupt.
Signed-off-by: Kamlakant Patel <kamlakant.patel@cavium.com>
Signed-off-by: George Cherian <george.cherian@cavium.com>
Reviewed-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There are no platform_data users anymore. Move the structs into the
driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
This header only contains platform_data. Move it to the proper directory.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
This header only contains platform_data. Move it to the proper directory.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Tony Lindgren <tony@atomide.com>
This header only contains platform_data. Move it to the proper directory.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
This header only contains platform_data. Move it to the proper directory.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>
This header only contains platform_data. Move it to the proper directory.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: James Hogan <jhogan@kernel.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Some data structure members were either misspelled or missing.
Fixes: aeb068c572 ("i2c: i2c-stm32f7: add driver")
Fixes: 380b8a85e7 ("i2c: i2c-stm32f7: Add initial SMBus protocols support")
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
With CONFIG_PM, we get a harmless build warning:
drivers/i2c/busses/i2c-i801.c:1723:12: warning: ‘i801_resume’ defined but not used [-Wunused-function]
static int i801_resume(struct device *dev)
^~~~~~~~~~~
drivers/i2c/busses/i2c-i801.c:1714:12: warning: ‘i801_suspend’ defined but not used [-Wunused-function]
static int i801_suspend(struct device *dev)
^~~~~~~~~~~~
Follow design pattern from other drivers like i2c-brcmstb, i2c-mpc,
i2c-ocores, i2c-pnx, i2c-puv3, i2c-st, i2c-stu300 and i2c-mux-pca954x
and changing the ifdef CONFIG_PM to CONFIG_PM_SLEEP.
Fixes: a9c8088c79 ("i2c: i801: Don't restore config registers on runtime PM")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Trivial fix to spelling mistakes in dev_dbg messages
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is a difference between attempts and retries.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The else branch cannot be taken as i will always equal num.
Get rid of the whole construct.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
exynos5_i2c_xfer contains lots of dead code, let's remove it and simplify
the rest. The patch should not introduce functional changes.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Suggested-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Andi Shyti <andi@etezian.org>
Reviewed-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Low-level controller enable function __i2c_dw_enable is overloaded to
also handle disabling. What's worse, even though the documentation
requires polling the IC_ENABLE_STATUS register when disabling, this
is not done: polling needs to be requested specifically by calling
__i2c_dw_enable_and_wait, which can also poll on enabling, but that
doesn't work if the IC_ENABLE_STATUS register is not implemented.
This is quite confusing if not in fact backwards.
Especially since the documentation says that disabling should be
followed by polling, the driver should be using a separate function
where it does one-shot disables to make the optimization stand out.
This refactors the two functions so that requested status is given
in the name rather than in a boolean argument. Specifically:
- __i2c_dw_enable: enable without polling (in accordance with docs)
- __i2c_dw_disable: disable and do poll (also as suggested by docs)
- __i2c_dw_disable_nowait: disable without polling (Linux-specific)
No functional change.
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
[wsa: fixed blank lines in header file]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Returning zero is wrong in this case.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: 174a13aa86 ("i2c: Add viperboard i2c master driver")
Returning -1 (-EPERM) is not appropriate here, go with -EIO.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: 1b144df1d7 ("i2c: New PMC MSP71xx TWI bus driver")
Returning zero is wrong in this case.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: 1b144df1d7 ("i2c: New PMC MSP71xx TWI bus driver")
Not all revisions of DW I2C controller implement the enable status register.
On platforms where that's the case (e.g. BG2CD and SPEAr ARM SoCs), waiting
for enable will time out as reading the unimplemented register yields zero.
It was observed that reading the IC_ENABLE_STATUS register once suffices to
avoid getting it stuck on Bay Trail hardware, so replace polling with one
dummy read of the register.
Fixes: fba4adbbf6 ("i2c: designware: must wait for enable")
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Tested-by: Ben Gardner <gardner.ben@gmail.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
These days, the I2C core ensures that the embedded adapter device
ignores the PM states of its children already. Because the adapter
device is an opaque logical device, there is no need for drivers to
repeat that again.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
axxia_i2c_init() uses clk_get_rate() for idev->i2c_clk. clk_get_rate()
should only be called if the clock is enabled, so ensure that by moving
the clk_prepare_enable() call before the call to axxia_i2c_init().
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 08678b850c ("i2c: axxia: Add I2C driver for AXM55xx")
Signed-off-by: Tobias Jordan <Tobias.Jordan@elektrobit.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Give a clear testcase for people wishing to change this code. It is also
a reminder for me if people ask about it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It allows mlxcpld driver to be connected to pre-defined adapter number
equal or greater than one, in order to avoid current limitation, assuming
usage of id number one only.
Signed-off-by: Michael Shych <michaelsh@mellanox.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It fixes report about supported functionality.
Functionality can be different up to CPLD capability.
Fixes: 6bec23bff9 (i2c: mlxcpld: add master driver for mellanox systems)
Signed-off-by: Michael Shych <michaelsh@mellanox.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It adds support for smbus block read transaction. CPLD smbus block read bit
of capability register is verified during driver initialization, and driver
data is updated if such capability is available. In case an upper layer
requests a read transaction of length one and expects that length will be
the first received byte, driver will notify CPLD about SMBus block read
transaction flavor, so CPLD will know to execute such kind of transaction.
Signed-off-by: Michael Shych <michaelsh@mellanox.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It adds support for extended length of read and write transactions.
New CPLD logic allows double size of the read and write transactions
length. This feature is verified through capability register, which is
renamed from unclear LPF_REG to CPBLTY_REG. Two bits 5 and 6 of these
register are used for length capability detection, while only 01
combination indicates support of extended transaction length.
Others mean lack of such support.
Signed-off-by: Michael Shych <michaelsh@mellanox.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The usage of of_device_get_match_data() reduce the code size a bit.
Also, the only way to call mtk_i2c_probe() is to match an entry in
mtk_i2c_of_match[], so of_id cannot be NULL.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Exynos5440 is not actively developed, there are no development
boards available and probably there are no real products with it.
Remove wide-tree support for Exynos5440.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Restoring configuration registers is only needed when we hand control
to the firmware. This is never the case with runtime power
management. The device will autosuspend whenever not used, so avoid
useless register writes by defining suspend/resume only, and not
runtime_suspend/runtime_resume.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
With FIFO enabled it is possible to read multiple bytes
at once in the interrupt handler as long as RXRDY is
set. This may also reduce the number of interrupts.
This patch polls RXRDY and reads all available bytes at
once.
Signed-off-by: David Engraf <david.engraf@sysgo.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
[wsa: reformatted comment]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds a generic DMA API to implement DMA support for i2c-stm32fx
drivers
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds slave support for I2C controller embedded in STM32F7 SoC
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds support for 10-bit device address for STM32F7 I2C
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We found the I2C controller count register is unreliable sometimes,
that will cause I2C to lose data. Thus we can read the data count
from 'i2c_dev->count' instead of the I2C controller count register.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add one flag to indicate if the i2c controller has been in suspend state,
which can prevent i2c accesses after i2c controller is suspended following
system suspend.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On some systems, the BIOS expects certain SMBus register values to
match the hardware defaults. Restore these configuration registers at
shutdown time to avoid confusing the BIOS. This avoids hard-locking
such systems upon reboot.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@vger.kernel.org
Saving the original value of register SMBSLVCMD in
i801_enable_host_notify() doesn't work, because this function is
called not only at probe time but also at resume time. Do it in
i801_probe() instead, so that the saved value is not overwritten at
resume time.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 22e94bd677 ("i2c: i801: store and restore the SLVCMD register at load and unload")
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@vger.kernel.org # v4.10+
Pull i2c updates from Wolfram Sang:
-I2C core now reports proper OF style module alias. I'd like to repeat
the note from the commit msg here (Thanks, Javier!):
NOTE: This patch may break out-of-tree drivers that were relying
on this behavior, and only had an I2C device ID table even
when the device was registered via OF.
There are no remaining drivers in mainline that do this, but
out-of-tree drivers have to be fixed and define a proper OF
device ID table to have module auto-loading working.
- new driver for the SynQuacer I2C controller
- major refactoring of the QUP driver
- the piix4 driver now uses request_muxed_region which should fix a
long standing resource conflict with the sp5100_tco watchdog
- a bunch of small core & driver improvements
* 'i2c/for-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (53 commits)
i2c: add support for Socionext SynQuacer I2C controller
dt-bindings: i2c: add binding for Socionext SynQuacer I2C
i2c: Update i2c_trace_msg static key to modern api
i2c: fix parameter of trace_i2c_result
i2c: imx: avoid taking clk_prepare mutex in PM callbacks
i2c: imx: use clk notifier for rate changes
i2c: make i2c_check_addr_validity() static
i2c: rcar: fix mask value of prohibited bit
dt-bindings: i2c: document R8A77965 bindings
i2c: pca-platform: drop gpio from platform data
i2c: pca-platform: use device_property_read_u32
i2c: pca-platform: unconditionally use devm_gpiod_get_optional
sh: sh7785lcr: add GPIO lookup table for i2c controller reset
i2c: qup: reorganization of driver code to remove polling for qup v2
i2c: qup: reorganization of driver code to remove polling for qup v1
i2c: qup: send NACK for last read sub transfers
i2c: qup: fix buffer overflow for multiple msg of maximum xfer len
i2c: qup: change completion timeout according to transfer length
i2c: qup: use the complete transfer length to choose DMA mode
i2c: qup: proper error handling for i2c error in BAM mode
...
This is a cleaned up version of the I2C controller driver for
the Fujitsu F_I2C IP, which was never supported upstream, and
has now been incorporated into the Socionext SynQuacer SoC.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
[wsa: updated MAINTAINERS entry and removed two empty lines]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is unsafe, as the runtime PM callbacks are called from the PM
workqueue, so this may deadlock when handling an i2c attached clock,
which may already hold the clk_prepare mutex from another context.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Instead of repeatedly calling clk_get_rate for each transfer, register
a clock notifier to update the cached divider value each time the clock
rate actually changes.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This removes the entire architecture code for blackfin, cris, frv, m32r,
metag, mn10300, score, and tile, including the associated device drivers.
I have been working with the (former) maintainers for each one to ensure
that my interpretation was right and the code is definitely unused in
mainline kernels. Many had fond memories of working on the respective
ports to start with and getting them included in upstream, but also saw
no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company
in charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It seems
that all the SoC product lines are still around, but have not used the
custom CPU architectures for several years at this point. In contrast,
CPU instruction sets that remain popular and have actively maintained
kernel ports tend to all be used across multiple licensees.
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I made
sure that they are all unused. Some architectures (notably tile, mn10300,
and blackfin) are still being shipped in products with old kernels,
but those products will never be updated to newer kernel releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing their
support or getting it added to mainline gcc in the first place.
They all have patched gcc-7.3 ports that work to some degree, but
complete upstream support won't happen before gcc-8.1. Csky posted
their first kernel patch set last week, their situation will be similar.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fQ8z
-----END PGP SIGNATURE-----
Merge tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pul removal of obsolete architecture ports from Arnd Bergmann:
"This removes the entire architecture code for blackfin, cris, frv,
m32r, metag, mn10300, score, and tile, including the associated device
drivers.
I have been working with the (former) maintainers for each one to
ensure that my interpretation was right and the code is definitely
unused in mainline kernels. Many had fond memories of working on the
respective ports to start with and getting them included in upstream,
but also saw no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company in
charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It
seems that all the SoC product lines are still around, but have not
used the custom CPU architectures for several years at this point. In
contrast, CPU instruction sets that remain popular and have actively
maintained kernel ports tend to all be used across multiple licensees.
[ See the new nds32 port merged in the previous commit for the next
generation of "one company in charge of an SoC line, a CPU
microarchitecture and a software ecosystem" - Linus ]
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I
made sure that they are all unused. Some architectures (notably tile,
mn10300, and blackfin) are still being shipped in products with old
kernels, but those products will never be updated to newer kernel
releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing
their support or getting it added to mainline gcc in the first
place. They all have patched gcc-7.3 ports that work to some
degree, but complete upstream support won't happen before gcc-8.1.
Csky posted their first kernel patch set last week, their situation
will be similar
[ Palmer Dabbelt points out that RISC-V support is in mainline gcc
since gcc-7, although gcc-7.3.0 is the recommended minimum - Linus ]"
This really says it all:
2498 files changed, 95 insertions(+), 467668 deletions(-)
* tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (74 commits)
MAINTAINERS: UNICORE32: Change email account
staging: iio: remove iio-trig-bfin-timer driver
tty: hvc: remove tile driver
tty: remove bfin_jtag_comm and hvc_bfin_jtag drivers
serial: remove tile uart driver
serial: remove m32r_sio driver
serial: remove blackfin drivers
serial: remove cris/etrax uart drivers
usb: Remove Blackfin references in USB support
usb: isp1362: remove blackfin arch glue
usb: musb: remove blackfin port
usb: host: remove tilegx platform glue
pwm: remove pwm-bfin driver
i2c: remove bfin-twi driver
spi: remove blackfin related host drivers
watchdog: remove bfin_wdt driver
can: remove bfin_can driver
mmc: remove bfin_sdh driver
input: misc: remove blackfin rotary driver
input: keyboard: remove bf54x driver
...
The blackfin architecture is getting removed, so the
twi driver can also be removed.
Acked-by: Aaron Wu <aaron.wu@analog.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
According to documentation, Bit 7 of ICMSR is unused and 0 should be
written to it. Fix the mask accordingly.
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
[wsa: edited commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
-----BEGIN PGP SIGNATURE-----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=rCow
-----END PGP SIGNATURE-----
Merge tag 'at24-4.17-updates-for-wolfram' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into i2c/for-4.17
"three new special cases for device tree compatible strings"
Use device_property_read_u32 instead of of_property_read_u32_index to
lookup the "clock-frequency" property.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allow for the reset-gpios property to be defined in the device tree
or via a GPIO lookup table.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Following are the major issues in current driver code
1. The current driver simply assumes the transfer completion
whenever its gets any non-error interrupts and then simply do the
polling of available/free bytes in FIFO.
2. The block mode is not working properly since no handling in
being done for OUT_BLOCK_WRITE_REQ and IN_BLOCK_READ_READ.
3. An i2c transfer can contain multiple message and QUP v2
supports reconfiguration during run in which the mode should be same
for all the sub transfer. Currently the mode is being programmed
before every sub transfer which is functionally wrong. If one message
is less than FIFO length and other message is greater than FIFO
length, then transfers will fail.
Because of above, i2c v2 transfers of size greater than 64 are failing
with following error message
i2c_qup 78b6000.i2c: timeout for fifo out full
To make block mode working properly and move to use the interrupts
instead of polling, major code reorganization is required. Following
are the major changes done in this patch
1. Remove the polling of TX FIFO free space and RX FIFO available
bytes and move to interrupts completely. QUP has QUP_MX_OUTPUT_DONE,
QUP_MX_INPUT_DONE, OUT_BLOCK_WRITE_REQ and IN_BLOCK_READ_REQ
interrupts to handle FIFO’s properly so check all these interrupts.
2. Determine the mode for transfer before starting by checking
all the tx/rx data length in each message. The complete message can be
transferred either in DMA mode or Programmed IO by FIFO/Block mode.
in DMA mode, both tx and rx uses same mode but in PIO mode, the TX and
RX can be in different mode.
3. During write, For FIFO mode, TX FIFO can be directly written
without checking for FIFO space. For block mode, the QUP will generate
OUT_BLOCK_WRITE_REQ interrupt whenever it has block size of available
space.
4. During read, both TX and RX FIFO will be used. TX will be used
for writing tags and RX will be used for receiving the data. In QUP,
TX and RX can operate in separate mode so configure modes accordingly.
5. For read FIFO mode, wait for QUP_MX_INPUT_DONE interrupt which
will be generated after all the bytes have been copied in RX FIFO. For
read Block mode, QUP will generate IN_BLOCK_READ_REQ interrupts
whenever it has block size of available data.
6. Split the transfer in chunk of one QUP block size(256 bytes)
and schedule each block separately. QUP v2 supports reconfiguration
during run in which QUP can transfer multiple blocks without issuing a
stop events.
7. Port the SMBus block read support for new code changes.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Following are the major issues in current driver code
1. The current driver simply assumes the transfer completion
whenever its gets any non-error interrupts and then simply do the
polling of available/free bytes in FIFO.
2. The block mode is not working properly since no handling in
being done for OUT_BLOCK_WRITE_REQ and IN_BLOCK_READ_REQ.
Because of above, i2c v1 transfers of size greater than 32 are failing
with following error message
i2c_qup 78b6000.i2c: timeout for fifo out full
To make block mode working properly and move to use the interrupts
instead of polling, major code reorganization is required. Following
are the major changes done in this patch
1. Remove the polling of TX FIFO free space and RX FIFO available
bytes and move to interrupts completely. QUP has QUP_MX_OUTPUT_DONE,
QUP_MX_INPUT_DONE, OUT_BLOCK_WRITE_REQ and IN_BLOCK_READ_REQ
interrupts to handle FIFO’s properly so check all these interrupts.
2. During write, For FIFO mode, TX FIFO can be directly written
without checking for FIFO space. For block mode, the QUP will generate
OUT_BLOCK_WRITE_REQ interrupt whenever it has block size of available
space.
3. During read, both TX and RX FIFO will be used. TX will be used
for writing tags and RX will be used for receiving the data. In QUP,
TX and RX can operate in separate mode so configure modes accordingly.
4. For read FIFO mode, wait for QUP_MX_INPUT_DONE interrupt which
will be generated after all the bytes have been copied in RX FIFO. For
read Block mode, QUP will generate IN_BLOCK_READ_REQ interrupts
whenever it has block size of available data.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
According to I2c specification, “If a master-receiver sends a
repeated START condition, it sends a not-acknowledge (A) just
before the repeated START condition”. QUP v2 supports sending
of NACK without stop with QUP_TAG_V2_DATARD_NACK so added the
same.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The BAM mode requires buffer for start tag data and tx, rx SG
list. Currently, this is being taken for maximum transfer length
(65K). But an I2C transfer can have multiple messages and each
message can be of this maximum length so the buffer overflow will
happen in this case. Since increasing buffer length won’t be
feasible since an I2C transfer can contain any number of messages
so this patch does following changes to make i2c transfers working
for multiple messages case.
1. Calculate the required buffers for 2 maximum length messages
(65K * 2).
2. Split the descriptor formation and descriptor scheduling.
The idea is to fit as many messages in one DMA transfers for 65K
threshold value (max_xfer_sg_len). Whenever the sg_cnt is
crossing this, then schedule the BAM transfer and subsequent
transfer will again start from zero.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently the completion timeout is being taken according to
maximum transfer length which is too high if SCL is operating in
high frequency. This patch calculates timeout on the basis of
one-byte transfer time and uses the same for completion timeout.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently each message length in complete transfer is being
checked for determining DMA mode and if any of the message length
is less than FIFO length then non DMA mode is being used which
will increase overhead. DMA can be used for any length and it
should be determined with complete transfer length. Now, this
patch selects DMA mode if the total length is greater than FIFO
length.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently the i2c error handling in BAM mode is not working
properly in stress condition.
1. After an error, the FIFO are being written with FLUSH and
EOT tags which should not be required since already these tags
have been written in BAM descriptor itself.
2. QUP state is being moved to RESET in IRQ handler in case
of error. When QUP HW encounters an error in BAM mode then it
moves the QUP STATE to PAUSE state. In this case, I2C_FLUSH
command needs to be executed while moving to RUN_STATE by writing
to the QUP_STATE register with the I2C_FLUSH bit set to 1.
3. In Error case, sometimes, QUP generates more than one
interrupt which will trigger the complete again. After an error,
the flush operation will be scheduled after doing
reinit_completion which should be triggered by BAM IRQ callback.
If the second QUP IRQ comes during this time then it will call
the complete and the transfer function will assume the all the
BAM HW descriptors have been completed.
4. The release DMA is being called after each error which
will free the DMA tx and rx channels. The error like NACK is very
common in I2C transfer and every time this will be overhead. Now,
since the error handling is proper so this release channel can be
completely avoided.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Austin Christ <austinwc@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In case of FLUSH operation, BAM copies INPUT EOT FLUSH (0x94)
instead of normal EOT (0x93) tag in input data stream when an
input EOT tag is received during flush operation. So only one tag
will be written instead of 2 separate tags.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The role of FLUSH and EOT tag is to flush already scheduled
descriptors in BAM HW in case of error. EOT is required only
when descriptors are scheduled in RX FIFO. If all the messages
are WRITE, then only FLUSH tag will be used.
A single BAM transfer can have multiple read and write messages.
The EOT and FLUSH tags should be scheduled at the end of BAM HW
descriptors. Since the READ and WRITE can be present in any order
so for some of the cases, these tags are not being written
correctly.
Following is one of the example
READ, READ, READ, READ
Currently EOT and FLUSH tags are being written after each READ.
If QUP gets NACK for first READ itself, then flush will be
triggered. It will look for first FLUSH tag in TX FIFO and will
stop there so only descriptors for first READ descriptors be
flushed. All the scheduled descriptors should be cleared to
generate BAM DMA completion.
Now this patch is scheduling FLUSH and EOT only once after all the
descriptors. So, flush will clear all the scheduled descriptors and
BAM will generate the completion interrupt.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The rx_nents and tx_nents are redundant. rx_buf and tx_buf can
be used for total number of SG entries. Since rx_buf and tx_buf
give the impression that it is buffer instead of count so rename
it to tx_cnt and rx_cnt for giving it more meaningful variable
name.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
1. Assigns use_dma in qup_dev structure itself which will
help in subsequent patches to determine the mode in IRQ handler.
2. Does minor code reorganization for loops to reduce the
unnecessary comparison and assignment.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The QUP BSLP BAM generates the following error sometimes if the
current I2C DMA transfer fails and the flush operation has been
scheduled
“bam-dma-engine 7884000.dma: Cannot free busy channel”
If any I2C error comes during BAM DMA transfer, then the QUP I2C
interrupt will be generated and the flush operation will be
carried out to make I2C consume all scheduled DMA transfer.
Currently, the same completion structure is being used for BAM
transfer which has already completed without reinit. It will make
flush operation wait_for_completion_timeout completed immediately
and will proceed for freeing the DMA resources where the
descriptors are still in process.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Acked-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The file has been updated from 2016 to 2018 so fixed the
copyright years.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In case we receive NACK on DATA we shouldn't be resetting the controller,
rather we should issue STOP command. This will terminate the current
transaction and -EIO is returned.
While at that handle the SMBus Quick Command properly.
We shouldn't be setting the XLP9XX_I2C_CMD_READ/WRITE for such
transactions.
Signed-off-by: George Cherian <george.cherian@cavium.com>
Reviewed-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C bus enters the STOP condition after the DATA_DONE interrupt is raised.
Essentially the driver should be checking the bus state before sending
any transaction. In case a transaction is initiated while the
bus is busy, the prior transaction's stop condition is not achieved.
Add the check to make sure the bus is not busy before every transaction.
Signed-off-by: George Cherian <george.cherian@cavium.com>
Reviewed-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The hardware may not support SDA hold time configuration, but if it is
not set in the Device Tree either, there is no need to print a warning.
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The errata FE-8471889 description has been updated. There is still a
timing violation for repeated start. But the errata now states that it
was only the case for the Standard mode (100 kHz), in Fast mode (400 kHz)
there is no issue.
This patch limit the errata fix to the Standard mode.
It has been tesed successfully on the clearfog (Aramda 388 based board).
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Suspend functions seem to have been copied from i2c-cadence driver.
Rename the functions to match the rest of the driver.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
These patches remove the metag architecture and tightly dependent
drivers from the kernel. With the 4.16 kernel the ancient gcc 4.2.4
based metag toolchain we have been using is hitting compiler bugs, so
now seems a good time to drop it altogether.
-----BEGIN PGP SIGNATURE-----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=zDIl
-----END PGP SIGNATURE-----
Merge tag 'metag_remove_2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jhogan/metag into asm-generic
Remove metag architecture
These patches remove the metag architecture and tightly dependent
drivers from the kernel. With the 4.16 kernel the ancient gcc 4.2.4
based metag toolchain we have been using is hitting compiler bugs, so
now seems a good time to drop it altogether.
* tag 'metag_remove_2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
i2c: img-scb: Drop METAG dependency
media: img-ir: Drop METAG dependency
watchdog: imgpdc: Drop METAG dependency
MAINTAINERS/CREDITS: Drop METAG ARCHITECTURE
tty: Remove metag DA TTY and console driver
clocksource: Remove metag generic timer driver
irqchip: Remove metag irqchip drivers
Drop a bunch of metag references
docs: Remove remaining references to metag
docs: Remove metag docs
metag: Remove arch/metag/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Now that arch/metag/ has been removed, remove the METAG dependency from
the IMG SCB I2C device driver. The hardware is also present on MIPS SoCs
so the driver still has value.
Signed-off-by: James Hogan <jhogan@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Cc: linux-i2c@vger.kernel.org
Cc: linux-metag@vger.kernel.org
ACPI_ERROR and ACPI_DEBUG_PRINT are not intended to be used by device
drivers. Use acpi_handle message logging functions instead.
As a nice side effect, it removes the following compiler warnings
which were printed when ACPI debug is disabled:
drivers/i2c/busses/i2c-scmi.c: In function "acpi_smbus_cmi_add_cap":
drivers/i2c/busses/i2c-scmi.c:328:39: warning: suggest braces around empty body in an "else" statement [-Wempty-body]
drivers/i2c/busses/i2c-scmi.c:338:12: warning: suggest braces around empty body in an "else" statement [-Wempty-body]
Suggested-by: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Accesses to SB800_PIIX4_SMB_IDX can occur from multiple drivers.
One example for another driver is the sp5100_tco driver.
Use request_muxed_region() to ensure synchronization.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The piix4 i2c driver is extremely slow. Replacing msleep()
with usleep_range() increases its speed substantially.
Use sleep ranges similar to those used in the i2c-801 driver
to keep things simple.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The error message:
[Fri Feb 16 13:42:13 2018] i2c-thunderx 0000:01:09.4: unhandled state: 0
is mis-leading as state 0 (bus error) is not an unknown state.
Return -EIO as before but avoid printing the message. Also rename
STAT_ERROR to STATE_BUS_ERROR.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The pointer reg is assigned a value that is never read, it is later
overwritten with a new value, hence the redundant initialization can
be removed.
Cleans up clang warning:
drivers/i2c/busses/i2c-stm32f4.c:352:16: warning: Value stored to 'reg'
during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
HSI2C_MASTER_ST_LOSE state is not documented properly, extensive tests
show that hardware is usually able to recover from this state without
interrupting the transfer. Moreover documentation says that
such state can be caused by slave clock stretching, and should not be
treated as an error during transaction. The only place it indicates
an error is just before starting transaction. In such case bus recovery
procedure should be performed - master should pulse SCL line nine times
and then send STOP condition, it can be repeated until SDA goes high.
The procedure can be performed using manual commands HSI2C_CMD_READ_DATA
and HSI2C_CMD_SEND_STOP.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In case of transaction with I2C_M_RECV_LEN set, make sure the driver reads
the first byte and then updates the RX fifo with the expected length. Set
threshold to 1 byte so that driver gets an interrupt on receiving the first byte.
After which the transfer length is updated depending on the received length.
Also report SMBus block read functionality.
Signed-off-by: George Cherian <george.cherian@cavium.com>
Tested-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix the driver violation of the common practice to return
ENXIO error on a slave address NACK.
Signed-off-by: Dmitry Bazhenov <dmitry.bazhenov@auriga.com>
Signed-off-by: George Cherian <george.cherian@cavium.com>
Tested-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
GPIO library can return -ENOSYS for the failed request.
Instead of failing ->probe() in this case override error code to 0.
Fixes: ca382f5b38 ("i2c: designware: add i2c gpio recovery option")
Reported-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We were leaving them in the power on state (or the state the firmware
had set up for some client, if we were taking over from them). The
boot state was 30 core clocks, when we actually want to sample some
time after (to make sure that the new input bit has actually arrived).
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Commits adding PCI IDs for Intel Braswell and Kaby Lake PCH-H lacked the
respective Kconfig and Documentation/i2c/busses/i2c-i801 change. Add
them now.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
One I2C bus on my Atom E3845 board has been broken since 4.9.
It has two devices, both declared by ACPI and with built-in drivers.
There are two back-to-back transactions originating from the kernel, one
targeting each device. The first transaction works, the second one locks
up the I2C controller. The controller never recovers.
These kernel logs show up whenever an I2C transaction is attempted after
this failure.
i2c-designware-pci 0000:00:18.3: timeout in disabling adapter
i2c-designware-pci 0000:00:18.3: timeout waiting for bus ready
Waiting for the I2C controller status to indicate that it is enabled
before programming it fixes the issue.
I have tested this patch on 4.14 and 4.15.
Fixes: commit 2702ea7dbe ("i2c: designware: wait for disable/enable only if necessary")
Cc: linux-stable <stable@vger.kernel.org> #4.13+
Signed-off-by: Ben Gardner <gardner.ben@gmail.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"I2C has the following changes for you:
- new flag to mark DMA safe buffers in i2c_msg. Also, some
infrastructure around it. And docs.
- huge refactoring of the at24 driver led by the new maintainer
Bartosz
- update I2C bus recovery to send STOP after recovery
- conversion from gpio to gpiod for I2C bus recovery
- adding a fault-injector to the i2c-gpio driver
- lots of small driver improvements, and bigger ones to
i2c-sh_mobile"
* 'i2c/for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (99 commits)
i2c: mv64xxx: Add myself as maintainer for this driver
i2c: mv64xxx: Fix clock resource by adding an optional bus clock
i2c: mv64xxx: Remove useless test before clk_disable_unprepare
i2c: mxs: use true and false for boolean values
i2c: meson: update doc description to fix build warnings
i2c: meson: add configurable divider factors
dt-bindings: i2c: update documentation for the Meson-AXG
i2c: imx-lpi2c: add runtime pm support
i2c: rcar: fix some trivial typos in comments
i2c: davinci: fix the cpufreq transition
i2c: rk3x: add proper kerneldoc header
i2c: rk3x: account for const type of of_device_id.data
i2c: acorn: remove outdated path from file header
i2c: acorn: add MODULE_LICENSE tag
i2c: rcar: implement bus recovery
i2c: send STOP after successful bus recovery
i2c: ensure SDA is released in recovery if SDA is controllable
i2c: add 'set_sda' to bus_recovery_info
i2c: add identifier in declarations for i2c_bus_recovery
i2c: make kerneldoc about bus recovery more precise
...
These are mostly minor bugfixes, cleanup and many defconfig updates to
support added drivers. In particular OMAP and PXA keep cleaning up the
legacy code base, as usual.
Nvidia adds some more SoC support code for Tegra 186.
For the first time on years, we are actually adding a non-DT platform for,
the EP93xx based Liebherr controller BK3.1. It's a minor variation of
the EP93xx reference design and in active use, while EP93xx apparently
doesn't have enough new development to have any device tree support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=frm4
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"These are mostly minor bugfixes, cleanup and many defconfig updates to
support added drivers. In particular OMAP and PXA keep cleaning up the
legacy code base, as usual.
Nvidia adds some more SoC support code for Tegra 186.
For the first time on years, we are actually adding a non-DT platform
for the EP93xx based Liebherr controller BK3.1. It's a minor variation
of the EP93xx reference design and in active use, while EP93xx
apparently doesn't have enough new development to have any device tree
support"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: omap: hwmod: fix section mismatch warnings
ARM: pxa/tosa-bt: add MODULE_LICENSE tag
arm64: defconfig: enable CONFIG_ACPI_APEI_EINJ
arm64: defconfig: enable EDAC GHES option
arm64: defconfig: enable CONFIG_ACPI_APEI_MEMORY_FAILURE
ARM: imx_v6_v7_defconfig: enable CONFIG_CPU_FREQ_STAT
Wind down ARM/TANGO port
ARM: davinci: constify gpio_led
ARM: davinci: drop unneeded newline
soc: Add SoC driver for Gemini
ARM: SAMSUNG: Add SPDX license identifiers
ARM: S5PV210: Add SPDX license identifiers
ARM: S3C64XX: Add SPDX license identifiers
ARM: S3C24XX: Add SPDX license identifiers
ARM: EXYNOS: Add SPDX license identifiers
ARM: imx: remove unused imx3 pm definitions
ARM: imx: don't abort MMDC probe if power saving status doesn't match
ARM: imx_v6_v7_defconfig: enable RTC_DRV_MXC_V2
ARM: imx_v6_v7_defconfig: Add missing config for DART-MX6 SoM
ARM: davinci: Use PTR_ERR_OR_ZERO()
...
On Armada 7K/8K we need to explicitly enable the bus clock. The bus clock
is optional because not all the SoCs need them but at least for Armada
7K/8K it is actually mandatory.
The binding documentation is updating accordingly.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
clk_disable_unprepare() already checks that the clock pointer is valid.
No need to test it before calling it.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Assign true or false to boolean variables instead of an integer value.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add description for 'data' parameter and drop unused 'irq' memeber.
Here is the warnings:
drivers/i2c/busses/i2c-meson.c:103: warning: No description found for
parameter 'data'
drivers/i2c/busses/i2c-meson.c:103: warning: Excess struct member 'irq'
description in 'meson_i2c'
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch try to add support for I2C controller in Meson-AXG SoC,
Due to the IP changes between I2C controller, we need to introduce
a compatible data to make the divider factor configurable.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jian Hu <jian.hu@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add runtime pm support to dynamically manage the clock to avoid enable/disable
clock in frequently that can improve the i2c bus transfer performance.
And use pm_runtime_force_suspend/resume() instead of lpi2c_imx_suspend/resume().
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Nothing big, but they get annoying after a while ;)
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c_davinci_cpufreq_transition() is implemented in a way that will
block if it ever gets called while no transfer is in progress.
Not only that, but reinit_completion() is never called for xfr_complete.
Use the fact that cpufreq uses an srcu_notifier (running in process
context) for transitions and that the bus_lock is taken during the call
to master_xfer() and simplify the code by removing the transfer
completion entirely and protecting i2c_davinci_cpufreq_transition()
with i2c_lock/unlock_adapter().
Reported-by: David Lechner <david@lechnology.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
* pm-core: (29 commits)
dmaengine: rcar-dmac: Make DMAC reinit during system resume explicit
PM / runtime: Allow no callbacks in pm_runtime_force_suspend|resume()
PM / runtime: Check ignore_children in pm_runtime_need_not_resume()
PM / runtime: Rework pm_runtime_force_suspend/resume()
PM / wakeup: Print warn if device gets enabled as wakeup source during sleep
PM / core: Propagate wakeup_path status flag in __device_suspend_late()
PM / core: Re-structure code for clearing the direct_complete flag
PM: i2c-designware-platdrv: Optimize power management
PM: i2c-designware-platdrv: Use DPM_FLAG_SMART_PREPARE
PM / mfd: intel-lpss: Use DPM_FLAG_SMART_SUSPEND
PCI / PM: Use SMART_SUSPEND and LEAVE_SUSPENDED flags for PCIe ports
PM / wakeup: Add device_set_wakeup_path() helper to control wakeup path
PM / core: Assign the wakeup_path status flag in __device_prepare()
PM / wakeup: Do not fail dev_pm_attach_wake_irq() unnecessarily
PM / core: Direct DPM_FLAG_LEAVE_SUSPENDED handling
PM / core: Direct DPM_FLAG_SMART_SUSPEND optimization
PM / core: Add helpers for subsystem callback selection
PM / wakeup: Drop redundant check from device_init_wakeup()
PM / wakeup: Drop redundant check from device_set_wakeup_enable()
PM / wakeup: only recommend "call"ing device_init_wakeup() once
...
gcc noticed the kerneldoc was wrongly formatted. Fix it!
drivers/i2c/busses/i2c-rk3x.c:164: warning:
Cannot understand * @grf_offset: ...
on line 164 - I thought it was a doc line
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
This driver creates a number of const structures that it stores in
the data field of an of_device_id array.
The data field of an of_device_id structure has type const void *, so
there is no need for a const-discarding cast when putting const values
into such a structure.
Furthermore, adding const to the declaration of the location that
receives a const value from such a field ensures that the compiler
will continue to check that the value is not modified. The
const-discarding cast on the extraction from the data field is thus
no longer needed.
Done using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
As of v4.15, Kbuild warns about missing MODULE_LICENSE tags:
WARNING: modpost: missing MODULE_LICENSE() in drivers/i2c/busses/i2c-acorn.o
This adds a license, author and description tag, matching the
comment at the start of the acorn i2c driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We can force levels of SCL and SDA, so we can use that for bus recovery.
Note that we cannot read SDA back, because we will only get the internal
state of the bus free detection.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Exynos-I2C uses default timeout of 1 second for the whole transaction,
including re-transmissions due to arbitration lost errors (-EAGAIN).
To allow re-transmissions driver's internal timeout should be significantly
lower, 100ms seems to be good candidate.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use only a portion of the data buffer for DMA transfers, which is always
16-byte aligned. This makes the DMA buffer address 16-byte aligned and
compensates for spurious hardware parity errors that may appear when the
DMA buffer address is not 16-byte aligned.
The data buffer is enlarged in order to accommodate any possible 16-byte
alignment offset and changes the DMA code to only use a portion of the
data buffer, which is 16-byte aligned.
The symptom of the hardware issue is the same as the one addressed in
v3.12-rc2-5-gbf41691 and manifests by transfers failing with EIO, with
bit 9 being set in the ERRSTS register.
Signed-off-by: Radu Rendec <radu.rendec@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove the facility for setting the prescaler value at compile time
entirely. It was only used for two SoCs, duplicating the actual value
for one of them and setting sometimes bogus value for another. Make all
MPC8xxx SoCs obtain their actual I2C clock prescaler from a single place
in the code.
Changes from v2:
- left Device Tree compatibles in place
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
According to the reference manuals for the corresponding SoCs, SEC
frequency ratio configuration is indicated by bit 26 of the POR Device
Status Register 2. Consequently, SEC_CFG bit should be tested by mask 0x20,
not 0x80. Testing the wrong bit leads to selection of wrong I2C clock
prescaler on those SoCs.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 8ce795cb0c ("i2c: mpc: assign the correct prescaler from SVR")
introduced the common helper function for obtaining the actual clock
prescaler value for MPC85xx. However, getting the prescaler for MPC8544
which depends on the SEC frequency ratio on this platform, has been always
performed separately based on the corresponding Device Tree configuration.
Move special handling of MPC8544 into that common helper. Make it dependent
on the SoC version and not on Device Tree compatible node, as is the case
with all other SoCs. Handle MPC8533 the same way which is similar
to MPC8544 in this regard, according to AN2919 "Determining the I2C
Frequency Divider Ratio for SCL".
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Obtaining the actual I2C clock prescaler value in mpc_i2c_setup_8xxx() only
happens when the clock parameter is set to something other than
MPC_I2C_CLOCK_LEGACY. When the clock parameter is exactly
MPC_I2C_CLOCK_LEGACY, the prescaler parameter is used in arithmetic
division as provided by the caller, resulting in a division by zero
for the majority of processors supported by the module.
Avoid division by zero by obtaining the actual I2C clock prescaler
in mpc_i2c_setup_8xxx() unconditionally regardless of the passed clock
value.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch dumps general and master registers at the end of transactions
when debugging is enabled. Previously, registers were only dumped before
submitting new descriptors (at the beginning of transactions).
This helps debugging if some registers change as result of a failed
transaction (e.g. bits are set in the ERRSTS general register).
Signed-off-by: Radu Rendec <radu.rendec@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make use of the new formula for more precise bus frequencies.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The formula to generate the desired bus speeds has changed a little over
time. Implement the new formula and allow drivers to opt-in by changing
to this new config set. Ensure in probe that we don't divide by zero.
The returned values on a R-Car H2 (r8a7790/Lager board) match the
suggested values in the datasheet.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Because we will add a second formula soon, put the sanity checks for the
computed results into a separate function.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Start RuntimePM a bit earlier, so we can use it to enable the clock
during probe for frequency calculations. Make sure it is enabled before
calling setup().
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Require the setup callback and move the frequency calculation into it.
This is in preparation for supporting multiple formulas.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The setup callback will be more generic and, thus, need to be able to
return error codes. Change the return type to 'int' for that.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
