The code checks the total number of iterations to differentiate
between regular scan and scheduled scan. However, regular scan has
a total of one iteration, not zero. As a result, regular scan will
have lower priority than it should have, and in case scheduled
scan is already running when regular scan is requested, regular scan
will be delayed until scheduled scan is aborted.
Fix that by checking for total iterations number of one as an
identifier for regular scan.
Fixes: 133c8259f8 ("iwlwifi: mvm: rename generic_scan_cmd functions to dwell")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When the card is not owned by the PCIe bus, we need to
acquire ownership first. This flow is implemented in
iwl_pcie_prepare_card_hw. Because of a hardware bug, we
need to disable link power management before we can
request ownership otherwise the other user of the device
won't get notified that we are requesting the device which
will prevent us from acquire ownership.
Same holds for the down flow where we need to make sure
that any other potential user is notified that the driver
is going down.
CC: <stable@vger.kernel.org> [4.1]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This fixes the byte order copying in the MAO (Mac Override
Section) section from the PNVM, as the byte swapping is not
required anymore in the 8000 family. Due to the byte
swapping, the driver was reporting an incorrect MAC
adddress.
CC: <stable@vger.kernel.org> [4.1]
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This reverts commit 5f17570354.
This patch introduced a high latency in buffer allocation
under extreme load. This latency caused a firmwre crash.
The same scenario works fine with this patch reverted.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add preemptive flag to scheduled scan command flags. Without this
flag, all scan requests after scheduled scan was started will be
delayed until scheduled scan stops. As a result, P2P_FIND will be
blocked while scheduled scan is active.
This flag was omitted during refactoring.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add new 3165 devices support.
Add one new 8000 series device support.
Remove support for 0x0000, 0xC030 and 0xD030 sub-system IDs
in the 8000 series.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The time event is initialized relatively late in interface (mvmvif)
initialization, so it's possible to fail before that happens. As a
consequence, the driver will crash if it ever tries to delete this
time event in case initialization was unsuccessful.
Avoid this by using the time event's vif pointer to indicate validity.
The vif pointer is != NULL whenever the id is != TE_MAX, except for
this special error case where the vif pointer will have the correct
property (as the whole memory is cleared on allocation) whereas the
id is 0, causing a crash in trying to delete the time event from the
list.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
For 8000 series, we need to access the device to know what
firmware to load. Before we do so, we need to prepare the
device otherwise we might not be able to access the
hardware.
Fixes: c278754a21e6 ("iwlwifi: mvm: support family 8000 B2/C steps")
CC: <stable@vger.kernel.org> [4.1]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
iwl_trans_pcie_alloc needs to return a non-zero value
if it fails. Otherwise the iwl_drv_start will think that
the allocation succeeded.
Remove the duplication of err and ret variable and use ret
which is the name we usually use in other places of the
driver.
Fixes: c278754a21e6 ("iwlwifi: mvm: support family 8000 B2/C steps")
CC: <stable@vger.kernel.org> [4.1]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
While cleanig the access to those hw-dependent registers,
instead of using the product family type, wrong condition was added
mistakenly and enabled 8000 family devices a forbidden access
to HW registers, fix it.
Fixes: 95411d0455 ("iwlwifi: pcie: Control access to the NIC's PM registers via iwl_cfg")
Signed-off-by: Dreyfuss, Haim <haim.dreyfuss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Sometimes when setting an igtk key the station maybe NULL.
In the of case igtk the function will skip to the end, and
try to print sta->addr, if sta is Null - we will access a
Null pointer.
Avoid accessing a Null pointer when setting a igtk key &
the sta == NULL, and print a default MAC address instead.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When BT is active, we want to avoid the shared antenna for
management frame to make sure we don't disturb BT. There
was a bug in that code because it chose the antenna
BIT(ANT_A) where ANT_A is already a bitmap (0x1). This
means that the antenna chosen in the end was ANT_B.
While this is not optimal on devices with 2 antennas (it'd
disturb BT), it is critical on single antenna devices like
3160 which couldn't connect at all when BT was active.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=97181
CC: <stable@vger.kernel.org> [3.17+]
Fixes: 34c8b24ff2 ("iwlwifi: mvm: BT Coex - avoid the shared antenna for management frames")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Pull networking updates from David Miller:
1) Add TX fast path in mac80211, from Johannes Berg.
2) Add TSO/GRO support to ibmveth, from Thomas Falcon
3) Move away from cached routes in ipv6, just like ipv4, from Martin
KaFai Lau.
4) Lots of new rhashtable tests, from Thomas Graf.
5) Run ingress qdisc lockless, from Alexei Starovoitov.
6) Allow servers to fetch TCP packet headers for SYN packets of new
connections, for fingerprinting. From Eric Dumazet.
7) Add mode parameter to pktgen, for testing receive. From Alexei
Starovoitov.
8) Cache access optimizations via simplifications of build_skb(), from
Alexander Duyck.
9) Move page frag allocator under mm/, also from Alexander.
10) Add xmit_more support to hv_netvsc, from KY Srinivasan.
11) Add a counter guard in case we try to perform endless reclassify
loops in the packet scheduler.
12) Extern flow dissector to be programmable and use it in new "Flower"
classifier. From Jiri Pirko.
13) AF_PACKET fanout rollover fixes, performance improvements, and new
statistics. From Willem de Bruijn.
14) Add netdev driver for GENEVE tunnels, from John W Linville.
15) Add ingress netfilter hooks and filtering, from Pablo Neira Ayuso.
16) Fix handling of epoll edge triggers in TCP, from Eric Dumazet.
17) Add an ECN retry fallback for the initial TCP handshake, from Daniel
Borkmann.
18) Add tail call support to BPF, from Alexei Starovoitov.
19) Add several pktgen helper scripts, from Jesper Dangaard Brouer.
20) Add zerocopy support to AF_UNIX, from Hannes Frederic Sowa.
21) Favor even port numbers for allocation to connect() requests, and
odd port numbers for bind(0), in an effort to help avoid
ip_local_port_range exhaustion. From Eric Dumazet.
22) Add Cavium ThunderX driver, from Sunil Goutham.
23) Allow bpf programs to access skb_iif and dev->ifindex SKB metadata,
from Alexei Starovoitov.
24) Add support for T6 chips in cxgb4vf driver, from Hariprasad Shenai.
25) Double TCP Small Queues default to 256K to accomodate situations
like the XEN driver and wireless aggregation. From Wei Liu.
26) Add more entropy inputs to flow dissector, from Tom Herbert.
27) Add CDG congestion control algorithm to TCP, from Kenneth Klette
Jonassen.
28) Convert ipset over to RCU locking, from Jozsef Kadlecsik.
29) Track and act upon link status of ipv4 route nexthops, from Andy
Gospodarek.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1670 commits)
bridge: vlan: flush the dynamically learned entries on port vlan delete
bridge: multicast: add a comment to br_port_state_selection about blocking state
net: inet_diag: export IPV6_V6ONLY sockopt
stmmac: troubleshoot unexpected bits in des0 & des1
net: ipv4 sysctl option to ignore routes when nexthop link is down
net: track link-status of ipv4 nexthops
net: switchdev: ignore unsupported bridge flags
net: Cavium: Fix MAC address setting in shutdown state
drivers: net: xgene: fix for ACPI support without ACPI
ip: report the original address of ICMP messages
net/mlx5e: Prefetch skb data on RX
net/mlx5e: Pop cq outside mlx5e_get_cqe
net/mlx5e: Remove mlx5e_cq.sqrq back-pointer
net/mlx5e: Remove extra spaces
net/mlx5e: Avoid TX CQE generation if more xmit packets expected
net/mlx5e: Avoid redundant dev_kfree_skb() upon NOP completion
net/mlx5e: Remove re-assignment of wq type in mlx5e_enable_rq()
net/mlx5e: Use skb_shinfo(skb)->gso_segs rather than counting them
net/mlx5e: Static mapping of netdev priv resources to/from netdev TX queues
net/mlx4_en: Use HW counters for rx/tx bytes/packets in PF device
...
Pull scheduler updates from Thomas Gleixner:
"This series of scheduler updates depends on sched/core and timers/core
branches, which are already in your tree:
- Scheduler balancing overhaul to plug a hard to trigger race which
causes an oops in the balancer (Peter Zijlstra)
- Lockdep updates which are related to the balancing updates (Peter
Zijlstra)"
* 'sched-hrtimers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched,lockdep: Employ lock pinning
lockdep: Implement lock pinning
lockdep: Simplify lock_release()
sched: Streamline the task migration locking a little
sched: Move code around
sched,dl: Fix sched class hopping CBS hole
sched, dl: Convert switched_{from, to}_dl() / prio_changed_dl() to balance callbacks
sched,dl: Remove return value from pull_dl_task()
sched, rt: Convert switched_{from, to}_rt() / prio_changed_rt() to balance callbacks
sched,rt: Remove return value from pull_rt_task()
sched: Allow balance callbacks for check_class_changed()
sched: Use replace normalize_task() with __sched_setscheduler()
sched: Replace post_schedule with a balance callback list
Pull locking updates from Thomas Gleixner:
"These locking updates depend on the alreay merged sched/core branch:
- Lockless top waiter wakeup for rtmutex (Davidlohr)
- Reduce hash bucket lock contention for PI futexes (Sebastian)
- Documentation update (Davidlohr)"
* 'sched-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/rtmutex: Update stale plist comments
futex: Lower the lock contention on the HB lock during wake up
locking/rtmutex: Implement lockless top-waiter wakeup
- CPU ops and PSCI (Power State Coordination Interface) refactoring
following the merging of the arm64 ACPI support, together with
handling of Trusted (secure) OS instances
- Using fixmap for permanent FDT mapping, removing the initial dtb
placement requirements (within 512MB from the start of the kernel
image). This required moving the FDT self reservation out of the
memreserve processing
- Idmap (1:1 mapping used for MMU on/off) handling clean-up
- Removing flush_cache_all() - not safe on ARM unless the MMU is off.
Last stages of CPU power down/up are handled by firmware already
- "Alternatives" (run-time code patching) refactoring and support for
immediate branch patching, GICv3 CPU interface access
- User faults handling clean-up
And some fixes:
- Fix for VDSO building with broken ELF toolchains
- Fixing another case of init_mm.pgd usage for user mappings (during
ASID roll-over broadcasting)
- Fix for FPSIMD reloading after CPU hotplug
- Fix for missing syscall trace exit
- Workaround for .inst asm bug
- Compat fix for switching the user tls tpidr_el0 register
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YeGl
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
"Mostly refactoring/clean-up:
- CPU ops and PSCI (Power State Coordination Interface) refactoring
following the merging of the arm64 ACPI support, together with
handling of Trusted (secure) OS instances
- Using fixmap for permanent FDT mapping, removing the initial dtb
placement requirements (within 512MB from the start of the kernel
image). This required moving the FDT self reservation out of the
memreserve processing
- Idmap (1:1 mapping used for MMU on/off) handling clean-up
- Removing flush_cache_all() - not safe on ARM unless the MMU is off.
Last stages of CPU power down/up are handled by firmware already
- "Alternatives" (run-time code patching) refactoring and support for
immediate branch patching, GICv3 CPU interface access
- User faults handling clean-up
And some fixes:
- Fix for VDSO building with broken ELF toolchains
- Fix another case of init_mm.pgd usage for user mappings (during
ASID roll-over broadcasting)
- Fix for FPSIMD reloading after CPU hotplug
- Fix for missing syscall trace exit
- Workaround for .inst asm bug
- Compat fix for switching the user tls tpidr_el0 register"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (42 commits)
arm64: use private ratelimit state along with show_unhandled_signals
arm64: show unhandled SP/PC alignment faults
arm64: vdso: work-around broken ELF toolchains in Makefile
arm64: kernel: rename __cpu_suspend to keep it aligned with arm
arm64: compat: print compat_sp instead of sp
arm64: mm: Fix freeing of the wrong memmap entries with !SPARSEMEM_VMEMMAP
arm64: entry: fix context tracking for el0_sp_pc
arm64: defconfig: enable memtest
arm64: mm: remove reference to tlb.S from comment block
arm64: Do not attempt to use init_mm in reset_context()
arm64: KVM: Switch vgic save/restore to alternative_insn
arm64: alternative: Introduce feature for GICv3 CPU interface
arm64: psci: fix !CONFIG_HOTPLUG_CPU build warning
arm64: fix bug for reloading FPSIMD state after CPU hotplug.
arm64: kernel thread don't need to save fpsimd context.
arm64: fix missing syscall trace exit
arm64: alternative: Work around .inst assembler bugs
arm64: alternative: Merge alternative-asm.h into alternative.h
arm64: alternative: Allow immediate branch as alternative instruction
arm64: Rework alternate sequence for ARM erratum 845719
...
for silicon that no one owns: these are really new features for
everyone.
* ARM: several features are in progress but missed the 4.2 deadline.
So here is just a smattering of bug fixes, plus enabling the VFIO
integration.
* s390: Some fixes/refactorings/optimizations, plus support for
2GB pages.
* x86: 1) host and guest support for marking kvmclock as a stable
scheduler clock. 2) support for write combining. 3) support for
system management mode, needed for secure boot in guests. 4) a bunch
of cleanups required for 2+3. 5) support for virtualized performance
counters on AMD; 6) legacy PCI device assignment is deprecated and
defaults to "n" in Kconfig; VFIO replaces it. On top of this there are
also bug fixes and eager FPU context loading for FPU-heavy guests.
* Common code: Support for multiple address spaces; for now it is
used only for x86 SMM but the s390 folks also have plans.
There are some x86 conflicts, one with the rc8 pull request and
the rest with Ingo's FPU rework.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJViYzhAAoJEL/70l94x66Dda0H/1IepMbfEy+o849d5G71fNTs
F8Y8qUP2GZuL7T53FyFUGSBw+AX7kimu9ia4gR/PmDK+QYsdosYeEjwlsolZfTBf
sHuzNtPoJhi5o1o/ur4NGameo0WjGK8f1xyzr+U8z74QDQyQv/QYCdK/4isp4BJL
ugHNHkuROX6Zng4i7jc9rfaSRg29I3GBxQUYpMkEnD3eMYMUBWGm6Rs8pHgGAMvL
vqzntgW00WNxehTqcAkmD/Wv+txxhkvIadZnjgaxH49e9JeXeBKTIR5vtb7Hns3s
SuapZUyw+c95DIipXq4EznxxaOrjbebOeFgLCJo8+XMXZum8RZf/ob24KroYad0=
=YsAR
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull first batch of KVM updates from Paolo Bonzini:
"The bulk of the changes here is for x86. And for once it's not for
silicon that no one owns: these are really new features for everyone.
Details:
- ARM:
several features are in progress but missed the 4.2 deadline.
So here is just a smattering of bug fixes, plus enabling the
VFIO integration.
- s390:
Some fixes/refactorings/optimizations, plus support for 2GB
pages.
- x86:
* host and guest support for marking kvmclock as a stable
scheduler clock.
* support for write combining.
* support for system management mode, needed for secure boot in
guests.
* a bunch of cleanups required for the above
* support for virtualized performance counters on AMD
* legacy PCI device assignment is deprecated and defaults to "n"
in Kconfig; VFIO replaces it
On top of this there are also bug fixes and eager FPU context
loading for FPU-heavy guests.
- Common code:
Support for multiple address spaces; for now it is used only for
x86 SMM but the s390 folks also have plans"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (124 commits)
KVM: s390: clear floating interrupt bitmap and parameters
KVM: x86/vPMU: Enable PMU handling for AMD PERFCTRn and EVNTSELn MSRs
KVM: x86/vPMU: Implement AMD vPMU code for KVM
KVM: x86/vPMU: Define kvm_pmu_ops to support vPMU function dispatch
KVM: x86/vPMU: introduce kvm_pmu_msr_idx_to_pmc
KVM: x86/vPMU: reorder PMU functions
KVM: x86/vPMU: whitespace and stylistic adjustments in PMU code
KVM: x86/vPMU: use the new macros to go between PMC, PMU and VCPU
KVM: x86/vPMU: introduce pmu.h header
KVM: x86/vPMU: rename a few PMU functions
KVM: MTRR: do not map huge page for non-consistent range
KVM: MTRR: simplify kvm_mtrr_get_guest_memory_type
KVM: MTRR: introduce mtrr_for_each_mem_type
KVM: MTRR: introduce fixed_mtrr_addr_* functions
KVM: MTRR: sort variable MTRRs
KVM: MTRR: introduce var_mtrr_range
KVM: MTRR: introduce fixed_mtrr_segment table
KVM: MTRR: improve kvm_mtrr_get_guest_memory_type
KVM: MTRR: do not split 64 bits MSR content
KVM: MTRR: clean up mtrr default type
...
- Disable the 32-bit vdso when building LE, so we can build with a 64-bit only
toolchain.
- EEH fixes from Gavin & Richard.
- Enable the sys_kcmp syscall from Laurent.
- Sysfs control for fastsleep workaround from Shreyas.
- Expose OPAL events as an irq chip by Alistair.
- MSI ops moved to pci_controller_ops by Daniel.
- Fix for kernel to userspace backtraces for perf from Anton.
- Merge pseries and pseries_le defconfigs from Cyril.
- CXL in-kernel API from Mikey.
- OPAL prd driver from Jeremy.
- Fix for DSCR handling & tests from Anshuman.
- Powernv flash mtd driver from Cyril.
- Dynamic DMA Window support on powernv from Alexey.
- LLVM clang fixes & workarounds from Anton.
- Reworked version of the patch to abort syscalls when transactional.
- Fix the swap encoding to support 4TB, from Aneesh.
- Various fixes as usual.
- Freescale updates from Scott: Highlights include more 8xx optimizations, an
e6500 hugetlb optimization, QMan device tree nodes, t1024/t1023 support, and
various fixes and cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=d9Wh
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
- disable the 32-bit vdso when building LE, so we can build with a
64-bit only toolchain.
- EEH fixes from Gavin & Richard.
- enable the sys_kcmp syscall from Laurent.
- sysfs control for fastsleep workaround from Shreyas.
- expose OPAL events as an irq chip by Alistair.
- MSI ops moved to pci_controller_ops by Daniel.
- fix for kernel to userspace backtraces for perf from Anton.
- merge pseries and pseries_le defconfigs from Cyril.
- CXL in-kernel API from Mikey.
- OPAL prd driver from Jeremy.
- fix for DSCR handling & tests from Anshuman.
- Powernv flash mtd driver from Cyril.
- dynamic DMA Window support on powernv from Alexey.
- LLVM clang fixes & workarounds from Anton.
- reworked version of the patch to abort syscalls when transactional.
- fix the swap encoding to support 4TB, from Aneesh.
- various fixes as usual.
- Freescale updates from Scott: Highlights include more 8xx
optimizations, an e6500 hugetlb optimization, QMan device tree nodes,
t1024/t1023 support, and various fixes and cleanup.
* tag 'powerpc-4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (180 commits)
cxl: Fix typo in debug print
cxl: Add CXL_KERNEL_API config option
powerpc/powernv: Fix wrong IOMMU table in pnv_ioda_setup_bus_dma()
powerpc/mm: Change the swap encoding in pte.
powerpc/mm: PTE_RPN_MAX is not used, remove the same
powerpc/tm: Abort syscalls in active transactions
powerpc/iommu/ioda2: Enable compile with IOV=on and IOMMU_API=off
powerpc/include: Add opal-prd to installed uapi headers
powerpc/powernv: fix construction of opal PRD messages
powerpc/powernv: Increase opal-irqchip initcall priority
powerpc: Make doorbell check preemption safe
powerpc/powernv: pnv_init_idle_states() should only run on powernv
macintosh/nvram: Remove as unused
powerpc: Don't use gcc specific options on clang
powerpc: Don't use -mno-strict-align on clang
powerpc: Only use -mtraceback=no, -mno-string and -msoft-float if toolchain supports it
powerpc: Only use -mabi=altivec if toolchain supports it
powerpc: Fix duplicate const clang warning in user access code
vfio: powerpc/spapr: Support Dynamic DMA windows
vfio: powerpc/spapr: Register memory and define IOMMU v2
...
Pull s390 updates from Martin Schwidefsky:
"Pretty boring for a merge window pull.
One change in behaviour is the patch for dasd driver, the module which
provides the diagnose discipline is now loaded automatically.
The SCLP code got a nice cleanup, a new global structure replaces a
bunch of accessor functions.
And a couple of random, small improvements"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/pci: improve handling of hotplug event 0x301
s390/setup: fix DMA_API_DEBUG warnings
s390/zcrypt: remove obsolete __constant
s390/keyboard: avoid off-by-one when using strnlen_user()
s390/sclp: pass timeout as HZ independent value
s390/mm: s/specifiation/specification/, s/an specification/a specification/
s390/sclp: Use DECLARE_BITMAP
s390/dasd: Enable automatic loading of dasd_diag_mod
s390/sclp: move sclp_facilities into "struct sclp"
s390/sclp: get rid of sclp_get_mtid() and sclp_get_mtid_max()
s390/sclp: unify basic sclp access by exposing "struct sclp"
s390/sclp: prepare smp_fill_possible_mask for global "struct sclp"
Add a new argument to br_fdb_delete_by_port which allows to specify a
vid to match when flushing entries and use it in nbp_vlan_delete() to
flush the dynamically learned entries of the vlan/port pair when removing
a vlan from a port. Before this patch only the local mac was being
removed and the dynamically learned ones were left to expire.
Note that the do_all argument is still respected and if specified, the
vid will be ignored.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a comment to explain why we're not disabling port's multicast when it
goes in blocking state. Since there's a check in the timer's function which
bypasses the timer if the port's in blocking/disabled state, the timer will
simply expire and stop without sending more queries.
Suggested-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mellanox/mlx4/main.c
net/packet/af_packet.c
Both conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
For AF_INET6 sockets, the value of struct ipv6_pinfo.ipv6only is
exported to userspace. It indicates whether a socket bound to in6addr_any
listens on IPv4 as well as IPv6. Since the socket is natively IPv6, it is not
listed by e.g. 'ss -l -4'.
This patch is accompanied by an appropriate one for iproute2 to enable
the additional information in 'ss -e'.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current implementation of descriptor init procedure only takes
care about setting/clearing ownership flag in "des0"/"des1"
fields while it is perfectly possible to get unexpected bits
set because of the following factors:
[1] On driver probe underlying memory allocated with
dma_alloc_coherent() might not be zeroed and so
it will be filled with garbage.
[2] During driver operation some bits could be set by SD/MMC
controller (for example error flags etc).
And unexpected and/or randomly set flags in "des0"/"des1"
fields may lead to unpredictable behavior of GMAC DMA block.
This change addresses both items above with:
[1] Use of dma_zalloc_coherent() instead of simple
dma_alloc_coherent() to make sure allocated memory is
zeroed. That shouldn't affect performance because
this allocation only happens once on driver probe.
[2] Do explicit zeroing of both "des0" and "des1" fields
of all buffer descriptors during initialization of
DMA transfer.
And while at it fixed identation of dma_free_coherent()
counterpart as well.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: arc-linux-dev@synopsys.com
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org
Cc: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Gospodarek says:
====================
changes to make ipv4 routing table aware of next-hop link status
This series adds the ability to have the Linux kernel track whether or
not a particular route should be used based on the link-status of the
interface associated with the next-hop.
Before this patch any link-failure on an interface that was serving as a
gateway for some systems could result in those systems being isolated
from the rest of the network as the stack would continue to attempt to
send frames out of an interface that is actually linked-down. When the
kernel is responsible for all forwarding, it should also be responsible
for taking action when the traffic can no longer be forwarded -- there
is no real need to outsource link-monitoring to userspace anymore.
This feature is only enabled with the new per-interface or ipv4 global
sysctls called 'ignore_routes_with_linkdown'.
net.ipv4.conf.all.ignore_routes_with_linkdown = 0
net.ipv4.conf.default.ignore_routes_with_linkdown = 0
net.ipv4.conf.lo.ignore_routes_with_linkdown = 0
...
When the above sysctls are set, the kernel will not only report to
userspace that the link is down, but it will also report to userspace
that a route is dead. This will signal to userspace that the route will
not be selected.
With the new sysctls set, the following behavior can be observed
(interface p8p1 is link-down):
default via 10.0.5.2 dev p9p1
10.0.5.0/24 dev p9p1 proto kernel scope link src 10.0.5.15
70.0.0.0/24 dev p7p1 proto kernel scope link src 70.0.0.1
80.0.0.0/24 dev p8p1 proto kernel scope link src 80.0.0.1 dead linkdown
90.0.0.0/24 via 80.0.0.2 dev p8p1 metric 1 dead linkdown
90.0.0.0/24 via 70.0.0.2 dev p7p1 metric 2
90.0.0.1 via 70.0.0.2 dev p7p1 src 70.0.0.1
cache
local 80.0.0.1 dev lo src 80.0.0.1
cache <local>
80.0.0.2 via 10.0.5.2 dev p9p1 src 10.0.5.15
cache
While the route does remain in the table (so it can be modified if
needed rather than being wiped away as it would be if IFF_UP was
cleared), the proper next-hop is chosen automatically when the link is
down. Now interface p8p1 is linked-up:
default via 10.0.5.2 dev p9p1
10.0.5.0/24 dev p9p1 proto kernel scope link src 10.0.5.15
70.0.0.0/24 dev p7p1 proto kernel scope link src 70.0.0.1
80.0.0.0/24 dev p8p1 proto kernel scope link src 80.0.0.1
90.0.0.0/24 via 80.0.0.2 dev p8p1 metric 1
90.0.0.0/24 via 70.0.0.2 dev p7p1 metric 2
192.168.56.0/24 dev p2p1 proto kernel scope link src 192.168.56.2
90.0.0.1 via 80.0.0.2 dev p8p1 src 80.0.0.1
cache
local 80.0.0.1 dev lo src 80.0.0.1
cache <local>
80.0.0.2 dev p8p1 src 80.0.0.1
cache
and the output changes to what one would expect.
If the global or interface sysctl is not set, the following output would
be expected when p8p1 is down:
default via 10.0.5.2 dev p9p1
10.0.5.0/24 dev p9p1 proto kernel scope link src 10.0.5.15
70.0.0.0/24 dev p7p1 proto kernel scope link src 70.0.0.1
80.0.0.0/24 dev p8p1 proto kernel scope link src 80.0.0.1 linkdown
90.0.0.0/24 via 80.0.0.2 dev p8p1 metric 1 linkdown
90.0.0.0/24 via 70.0.0.2 dev p7p1 metric 2
If the dead flag does not appear there should be no expectation that the
kernel would skip using this route due to link being down.
v2: Split kernel changes into 2 patches: first to add linkdown flag and
second to add new sysctl settings. Also took suggestion from Alex to
simplify code by only checking sysctl during fib lookup and suggestion
from Scott to add a per-interface sysctl. Added iproute2 patch to
recognize and print linkdown flag.
v3: Code cleanups along with reverse-path checks suggested by Alex and
small fixes related to problems found when multipath was disabled.
v4: Drop binary sysctls
v5: Whitespace and variable declaration fixups suggested by Dave
v6: Style changes noticed by Dave and checkpath suggestions.
v7: Last checkpatch fixup.
Though there were some that preferred not to have a configuration option
and to make this behavior the default when it was discussed in Ottawa
earlier this year since "it was time to do this." I wanted to propose
the config option to preserve the current behavior for those that desire
it. I'll happily remove it if Dave and Linus approve.
An IPv6 implementation is also needed (DECnet too!), but I wanted to
start with the IPv4 implementation to get people comfortable with the
idea before moving forward. If this is accepted the IPv6 implementation
can be posted shortly.
There was also a request for switchdev support for this, but that will
be posted as a followup as switchdev does not currently handle dead
next-hops in a multi-path case and I felt that infra needed to be added
first.
FWIW, we have been running the original version of this series with a
global sysctl and our customers have been happily using a backported
version for IPv4 and IPv6 for >6 months.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This feature is only enabled with the new per-interface or ipv4 global
sysctls called 'ignore_routes_with_linkdown'.
net.ipv4.conf.all.ignore_routes_with_linkdown = 0
net.ipv4.conf.default.ignore_routes_with_linkdown = 0
net.ipv4.conf.lo.ignore_routes_with_linkdown = 0
...
When the above sysctls are set, will report to userspace that a route is
dead and will no longer resolve to this nexthop when performing a fib
lookup. This will signal to userspace that the route will not be
selected. The signalling of a RTNH_F_DEAD is only passed to userspace
if the sysctl is enabled and link is down. This was done as without it
the netlink listeners would have no idea whether or not a nexthop would
be selected. The kernel only sets RTNH_F_DEAD internally if the
interface has IFF_UP cleared.
With the new sysctl set, the following behavior can be observed
(interface p8p1 is link-down):
default via 10.0.5.2 dev p9p1
10.0.5.0/24 dev p9p1 proto kernel scope link src 10.0.5.15
70.0.0.0/24 dev p7p1 proto kernel scope link src 70.0.0.1
80.0.0.0/24 dev p8p1 proto kernel scope link src 80.0.0.1 dead linkdown
90.0.0.0/24 via 80.0.0.2 dev p8p1 metric 1 dead linkdown
90.0.0.0/24 via 70.0.0.2 dev p7p1 metric 2
90.0.0.1 via 70.0.0.2 dev p7p1 src 70.0.0.1
cache
local 80.0.0.1 dev lo src 80.0.0.1
cache <local>
80.0.0.2 via 10.0.5.2 dev p9p1 src 10.0.5.15
cache
While the route does remain in the table (so it can be modified if
needed rather than being wiped away as it would be if IFF_UP was
cleared), the proper next-hop is chosen automatically when the link is
down. Now interface p8p1 is linked-up:
default via 10.0.5.2 dev p9p1
10.0.5.0/24 dev p9p1 proto kernel scope link src 10.0.5.15
70.0.0.0/24 dev p7p1 proto kernel scope link src 70.0.0.1
80.0.0.0/24 dev p8p1 proto kernel scope link src 80.0.0.1
90.0.0.0/24 via 80.0.0.2 dev p8p1 metric 1
90.0.0.0/24 via 70.0.0.2 dev p7p1 metric 2
192.168.56.0/24 dev p2p1 proto kernel scope link src 192.168.56.2
90.0.0.1 via 80.0.0.2 dev p8p1 src 80.0.0.1
cache
local 80.0.0.1 dev lo src 80.0.0.1
cache <local>
80.0.0.2 dev p8p1 src 80.0.0.1
cache
and the output changes to what one would expect.
If the sysctl is not set, the following output would be expected when
p8p1 is down:
default via 10.0.5.2 dev p9p1
10.0.5.0/24 dev p9p1 proto kernel scope link src 10.0.5.15
70.0.0.0/24 dev p7p1 proto kernel scope link src 70.0.0.1
80.0.0.0/24 dev p8p1 proto kernel scope link src 80.0.0.1 linkdown
90.0.0.0/24 via 80.0.0.2 dev p8p1 metric 1 linkdown
90.0.0.0/24 via 70.0.0.2 dev p7p1 metric 2
Since the dead flag does not appear, there should be no expectation that
the kernel would skip using this route due to link being down.
v2: Split kernel changes into 2 patches, this actually makes a
behavioral change if the sysctl is set. Also took suggestion from Alex
to simplify code by only checking sysctl during fib lookup and
suggestion from Scott to add a per-interface sysctl.
v3: Code clean-ups to make it more readable and efficient as well as a
reverse path check fix.
v4: Drop binary sysctl
v5: Whitespace fixups from Dave
v6: Style changes from Dave and checkpatch suggestions
v7: One more checkpatch fixup
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a fib flag called RTNH_F_LINKDOWN to any ipv4 nexthops that are
reachable via an interface where carrier is off. No action is taken,
but additional flags are passed to userspace to indicate carrier status.
This also includes a cleanup to fib_disable_ip to more clearly indicate
what event made the function call to replace the more cryptic force
option previously used.
v2: Split out kernel functionality into 2 patches, this patch simply
sets and clears new nexthop flag RTNH_F_LINKDOWN.
v3: Cleanups suggested by Alex as well as a bug noticed in
fib_sync_down_dev and fib_sync_up when multipath was not enabled.
v5: Whitespace and variable declaration fixups suggested by Dave.
v6: Style fixups noticed by Dave; ran checkpatch to be sure I got them
all.
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
switchdev_port_bridge_getlink() queries SWITCHDEV_ATTR_PORT_BRIDGE_FLAGS
attributes, but a driver doesn't need to implement this in order to get
bridge link information.
So error out only on errors different than -EOPNOTSUPP.
(This is a follow-up patch for 7d4f8d8.)
Fixes: 8793d0a664 ("switchdev: add new switchdev_port_bridge_getlink")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This bug pops up with NetworkManager on Fedora 21. NetworkManager tends to
stop the interface (nicvf_stop() is called) before changing settings. In
stopped state MAC cannot be sent to a PF. However, when the interface is
restarted (nicvf_open() is called), we ping the PF using NIC_MBOX_MSG_READY
message, and the PF replies back with old MAC address, overriding what we
had after MAC setting from userspace. As a result, we cannot set MAC
address using NetworkManager.
This patch introduces special tracking of MAC change in stopped state so
that the correct new MAC address is sent to a PF when interface is reopen.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ICMP messages can trigger ICMP and local errors. In this case
serr->port is 0 and starting from Linux 4.0 we do not return
the original target address to the error queue readers.
Add function to define which errors provide addr_offset.
With this fix my ping command is not silent anymore.
Fixes: c247f0534c ("ip: fix error queue empty skb handling")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz says:
====================
Mellanox NIC drivers update, June 23 2015
This series has two fixes from Eran to his recent SRIOV counters work in
mlx4 and few more updates from Saeed and Achiad to the mlx5 Ethernet
code. All fixes here relate to net-next code, so no need for -stable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefetch the 1st cache line used by the buffer pointed by
the skb linear data.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate between mlx5e_get_cqe() and mlx5_cqwq_pop(), this helps for
better code readability and better CQ buffer management.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use container_of() instead.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Coding Style fix, remove extra spaces.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to save PCI BW consumed by TX CQEs and to reduce the amount of
CPU cache misses caused by TX CQE reading, we request TX CQE generation
only when skb->xmit_more=0.
As a consequence of the above, a single TX CQE may now indicate the
transmission completion of multiple TX SKBs.
This also handles a problem introduced in commit b1b8105ebf41 "net/mlx5e:
Support NETIF_F_SG" where we didn't ask for NOP completions while the
driver didn't have the proper code to handle this case.
Fixes: b1b8105ebf41 ('net/mlx5e: Support NETIF_F_SG')
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NOP completion SKBs are always NULL.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is already assigned at mlx5e_build_rq_param()
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of counting number of gso fragments, we can use
skb_shinfo(skb)->gso_segs.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To save per-packet calculations, we use the following static mappings:
1) priv {channel, tc} to netdev txq (used @mlx5e_selec_queue())
2) netdev txq to priv sq (used @mlx5e_xmit())
Thanks to these static mappings, no more need for a separate implementation
of ndo_start_xmit when multiple TCs are configured.
We believe the performance improvement of such separation would be negligible, if any.
The previous way of dynamically calculating the above mappings required
allocating more TX queues than actually used (@alloc_etherdev_mqs()),
which is now no longer needed.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under SRIOV, the port rx/tx bytes/packets statistics should by read
from the HW instead of using the PF netdevice SW accounting. This is
needed in order to get the full port statistics and not just the PF
own ones
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NUM_ALL_STATS was not updated with the new four entries, instead
NUM_FLOW_STATS was updated, fix it. that caused off-by-four for all
counters below pf_*_*.
Fixes: b42de4d012 ('net/mlx4_en: Show PF own statistics via ethtool')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This time with bigger changes than usual:
* A new IOMMU driver for the ARM SMMUv3. This IOMMU is pretty
different from SMMUv1 and v2 in that it is configured through
in-memory structures and not through the MMIO register region.
The ARM SMMUv3 also supports IO demand paging for PCI devices
with PRI/PASID capabilities, but this is not implemented in
the driver yet.
* Lots of cleanups and device-tree support for the Exynos IOMMU
driver. This is part of the effort to bring Exynos DRM support
upstream.
* Introduction of default domains into the IOMMU core code. The
rationale behind this is to move functionalily out of the
IOMMU drivers to common code to get to a unified behavior
between different drivers.
The patches here introduce a default domain for iommu-groups
(isolation groups). A device will now always be attached to a
domain, either the default domain or another domain handled by
the device driver. The IOMMU drivers have to be modified to
make use of that feature. So long the AMD IOMMU driver is
converted, with others to follow.
* Patches for the Intel VT-d drvier to fix DMAR faults that
happen when a kdump kernel boots. When the kdump kernel boots
it re-initializes the IOMMU hardware, which destroys all
mappings from the crashed kernel. As this happens before
the endpoint devices are re-initialized, any in-flight DMA
causes a DMAR fault. These faults cause PCI master aborts,
which some devices can't handle properly and go into an
undefined state, so that the device driver in the kdump kernel
fails to initialize them and the dump fails.
This is now fixed by copying over the mapping structures (only
context tables and interrupt remapping tables) from the old
kernel and keep the old mappings in place until the device
driver of the new kernel takes over. This emulates the the
behavior without an IOMMU to the best degree possible.
* A couple of other small fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=Zicw
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"This time with bigger changes than usual:
- A new IOMMU driver for the ARM SMMUv3.
This IOMMU is pretty different from SMMUv1 and v2 in that it is
configured through in-memory structures and not through the MMIO
register region. The ARM SMMUv3 also supports IO demand paging for
PCI devices with PRI/PASID capabilities, but this is not
implemented in the driver yet.
- Lots of cleanups and device-tree support for the Exynos IOMMU
driver. This is part of the effort to bring Exynos DRM support
upstream.
- Introduction of default domains into the IOMMU core code.
The rationale behind this is to move functionalily out of the IOMMU
drivers to common code to get to a unified behavior between
different drivers. The patches here introduce a default domain for
iommu-groups (isolation groups).
A device will now always be attached to a domain, either the
default domain or another domain handled by the device driver. The
IOMMU drivers have to be modified to make use of that feature. So
long the AMD IOMMU driver is converted, with others to follow.
- Patches for the Intel VT-d drvier to fix DMAR faults that happen
when a kdump kernel boots.
When the kdump kernel boots it re-initializes the IOMMU hardware,
which destroys all mappings from the crashed kernel. As this
happens before the endpoint devices are re-initialized, any
in-flight DMA causes a DMAR fault. These faults cause PCI master
aborts, which some devices can't handle properly and go into an
undefined state, so that the device driver in the kdump kernel
fails to initialize them and the dump fails.
This is now fixed by copying over the mapping structures (only
context tables and interrupt remapping tables) from the old kernel
and keep the old mappings in place until the device driver of the
new kernel takes over. This emulates the the behavior without an
IOMMU to the best degree possible.
- A couple of other small fixes and cleanups"
* tag 'iommu-updates-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (69 commits)
iommu/amd: Handle large pages correctly in free_pagetable
iommu/vt-d: Don't disable IR when it was previously enabled
iommu/vt-d: Make sure copied over IR entries are not reused
iommu/vt-d: Copy IR table from old kernel when in kdump mode
iommu/vt-d: Set IRTA in intel_setup_irq_remapping
iommu/vt-d: Disable IRQ remapping in intel_prepare_irq_remapping
iommu/vt-d: Move QI initializationt to intel_setup_irq_remapping
iommu/vt-d: Move EIM detection to intel_prepare_irq_remapping
iommu/vt-d: Enable Translation only if it was previously disabled
iommu/vt-d: Don't disable translation prior to OS handover
iommu/vt-d: Don't copy translation tables if RTT bit needs to be changed
iommu/vt-d: Don't do early domain assignment if kdump kernel
iommu/vt-d: Allocate si_domain in init_dmars()
iommu/vt-d: Mark copied context entries
iommu/vt-d: Do not re-use domain-ids from the old kernel
iommu/vt-d: Copy translation tables from old kernel
iommu/vt-d: Detect pre enabled translation
iommu/vt-d: Make root entry visible for hardware right after allocation
iommu/vt-d: Init QI before root entry is allocated
iommu/vt-d: Cleanup log messages
...
JFFS2
* fix a theoretical unbalanced locking issue; the lock handling was a bit
unclean, but AFAICT, it didn't actually lead to real deadlocks
NAND
* brcmnand driver: new driver supporting NAND controller found originally on
Broadcom STB SoCs (BCM7xxx), but now also found on BCM63xxx, iProc (e.g.,
Cygnus, BCM5301x), BCM3xxx, and more
* Begin factoring out BBT code so it can be shared between traditional
(parallel) NAND drivers and upcoming SPI NAND drivers (WIP)
* Add common DT-based init support, so nand_base can pick up some flash
properties automatically, using established common NAND DT properties
* mxc_nand: support 8-bit ECC
* pxa3xx_nand:
- fix build for ARM64
- use a jiffies-based timeout
SPI NOR
* Add a few new IDs
* Clear out some unnecessary entries
* Make sure SECT_4K flags are correct for all (?) entries
Core
* Fix mtd->usecount race conditions (BUG_ON())
* Switch to modern PM ops
Other
* CFI: save code space by de-inlining large functions
* Clean up some partition parser selection code across several drivers
* Various miscellaneous changes, mostly minor
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=JN5N
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20150623' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"JFFS2:
- fix a theoretical unbalanced locking issue; the lock handling was a
bit unclean, but AFAICT, it didn't actually lead to real deadlocks
NAND:
- brcmnand driver: new driver supporting NAND controller found
originally on Broadcom STB SoCs (BCM7xxx), but now also found on
BCM63xxx, iProc (e.g., Cygnus, BCM5301x), BCM3xxx, and more
- begin factoring out BBT code so it can be shared between
traditional (parallel) NAND drivers and upcoming SPI NAND drivers
(WIP)
- add common DT-based init support, so nand_base can pick up some
flash properties automatically, using established common NAND DT
properties
- mxc_nand: support 8-bit ECC
- pxa3xx_nand:
* fix build for ARM64
* use a jiffies-based timeout
SPI NOR:
- add a few new IDs
- clear out some unnecessary entries
- make sure SECT_4K flags are correct for all (?) entries
Core:
- fix mtd->usecount race conditions (BUG_ON())
- switch to modern PM ops
Other:
- CFI: save code space by de-inlining large functions
- clean up some partition parser selection code across several
drivers
- various miscellaneous changes, mostly minor"
* tag 'for-linus-20150623' of git://git.infradead.org/linux-mtd: (57 commits)
mtd: docg3: Fix kasprintf() usage
mtd: docg3: Don't leak docg3->bbt in error path
mtd: nandsim: Fix kasprintf() usage
mtd: cs553x_nand: Fix kasprintf() usage
mtd: r852: Fix device_create_file() usage
mtd: brcmnand: drop unnecessary initialization
mtd: propagate error codes from add_mtd_device()
mtd: diskonchip: remove two-phase partitioning / registration
mtd: dc21285: use raw spinlock functions for nw_gpio_lock
mtd: chips: fixup dependencies, to prevent build error
mtd: cfi_cmdset_0002: Initialize datum before calling map_word_load_partial
mtd: cfi: deinline large functions
mtd: lantiq-flash: use default partition parsers
mtd: plat_nand: use default partition probe
mtd: nand: correct indentation within conditional
mtd: remove incorrect file name
mtd: blktrans: use better error code for unimplemented ioctl()
mtd: maps: Spelling s/reseved/reserved/
mtd: blktrans: change blktrans_getgeo return value
mtd: mxc_nand: generate nand_ecclayout for 8 bit ECC
...
Another fairly quiet release, some new drivers with generic handling for
minor features but nothing that makes a substantial difference outside
of the subsystem or for most boards:
- Support for a bunch of new parameters which are present on enough
regulators to be worth having generic handling for in the framework.
- Fixes for some issues with printing constraints during boot which
should probably have gone in for v4.1 but didn't.
- New drivers for Dialog DA9062, Maxim MAX77621 and Qualcomm SPMI regulators.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJViYM8AAoJECTWi3JdVIfQxBkH/iWXaFGXaH4N42jKbo0RnKWT
JtKCQwVEilVDFjixt9fNDzlEX0ErZ9wuYvYYRkCGZqhwFwhZe2Pg1BGmN/e5o8dk
6OS3ZNiybBuUNHHio+toZyhJsJoSJubP7MZsWBpJ5evWYmnmqGS589LnlsZwJ7Ez
5W5YUU8GmwyUk2dEa+WpnT3jBJqfccuCzET68jtZz+koRIO0l/gpAgwhVoC/iF2J
LYn1r4Cvp0hOcvPJsbTsXUKDIeMk4jfvuYDzBXUyC21fsG2qPlvuYo3nKjhTnMBC
gxQcPzbUbfakRH6R5GFdFx+rhvzSKc4dlula5cOF9n++eVFQ6jwHqBk/XvSKRVc=
=e9Ij
-----END PGP SIGNATURE-----
Merge tag 'regulator-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"Another fairly quiet release, some new drivers with generic handling
for minor features but nothing that makes a substantial difference
outside of the subsystem or for most boards:
- support for a bunch of new parameters which are present on enough
regulators to be worth having generic handling for in the
framework.
- fixes for some issues with printing constraints during boot which
should probably have gone in for v4.1 but didn't.
- new drivers for Dialog DA9062, Maxim MAX77621 and Qualcomm SPMI
regulators"
* tag 'regulator-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (45 commits)
regulator: qcom_spmi: Fix calculating number of voltages
regulator: qcom_spmi: Add missing braces for aligned code
regulator: fix simple_return.cocci warnings
regulator: Add QCOM SPMI regulator driver
regulator: Add docbook for soft start
regulator: Add input current limit support
regulator: Add soft start support
regulator: Add pull down support
regulator: Add system_load constraint
regulator: max8973: Fix up ramp_delay for MAX8973_RAMP_25mV_PER_US case
regulator: core: replace sprintf with scnprintf
regulator: core: fix constraints output buffer
regulator: core: Don't corrupt display when printing uV offsets
regulator: max8973: add support for MAX77621
regulator: max8973: configure ramp delay through callback
regulator: pwm-regulator: Diffientiate between dev (device) and rdev (regulator_dev)
regulator: pwm-regulator: Remove superfluous is_enabled check
regulator: pwm-regulator: Remove unnecessary descriptor attribute from ddata
regulator: core: Don't spew backtraces on duplicate sysfs
regulator: da9063: Fix up irq leak
...
No framework updates for the SPI API this time around aside from one
small fix, just driver improvments. Some highlights include:
- New driver support for CSR USP, Mikrotik RB4xx and Zynq GQSPI
controllers.
- Modernisation of the OMAP McSPI controller driver, moving it to
current APIs to enable support for a wider range of client drivers.
- DMA support for the bcm2835 controller.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJViTdyAAoJECTWi3JdVIfQxY0H/2dWW+6SIt+To4WHDQDkKluA
QsT2n+t05LMukdWkD+fiaXMJ+4yqY1Dg8oNRUJeGCltRTJWmcjZep44hRpMv3EJd
oswPwKcfBMQ5jP3iwoiZvZiJxhTVBm2xJerOtL8ZyALovmU4BPN1VUpq+t1+yLnF
O53DnuIN29PEm2/VGK1+HlWNRebMEAsG/wlPvkFBT3TyIVwLAoMuYwkRMeK9XVnN
J9sgdsxQwKwKk6Vnh1oZ2uht83PFrMpZIyX2pKYLGRLxJ8ZYBOPUnAdqbWfDXA9t
rexsQdNWjJrcyIRJh1NqRnnIA43q6AgdPsCgg8eaI+1Jx3F2Bp+SpRjwK91KW+I=
=0yyj
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"No framework updates for the SPI API this time around aside from one
small fix, just driver improvments. Some highlights include:
- New driver support for CSR USP, Mikrotik RB4xx and Zynq GQSPI
controllers.
- Modernisation of the OMAP McSPI controller driver, moving it to
current APIs to enable support for a wider range of client drivers.
- DMA support for the bcm2835 controller"
* tag 'spi-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (60 commits)
spi: zynq: Remove execute bit
spi: atmel: add support to FIFOs
spi: atmel: update DT bindings documentation
spi: spi-fsl-dspi: Update DT binding documentation
spi: pxa2xx: Constify ACPI device ids
spi: Add support for Zynq Ultrascale+ MPSoC GQSPI controller
spi: zynq: Add DT bindings documentation for Zynq Ultrascale+ MPSoC GQSPI controller
spi: fsl-dspi: Use pinctrl PM helpers
spi: davinci: change the lower limit of pre-scale divider to 1
spi: spi-fsl-dspi: Change the way of increasing spi_message->actual_length
spi: spi-fsl-dspi: Enable TCF interrupt mode support
spi: atmel: add support for the internal chip-select of the spi controller
spi: spi-pxa2xx: remove legacy PXA DMA bits
spi: pxa2xx: Make LPSS SPI general register optional
spi: pxa2xx: Prepare for new Intel LPSS SPI type
spi: pxa2xx: Differentiate Intel LPSS types
spi: restore rx/tx_buf in case of unset CONFIG_HAS_DMA
spi: rspi: Re-do the returning value of qspi_transfer_out_in
spi: rspi: modify the name of "qspi_trigger_transfer_out_int" function
spi: orion: Fix extended baud rates for each Armada SoCs
...
As well as a few fixes and updates for API changes there's two new
features for the API:
- Better support for handling a reset of the underlying hardware,
marking the register map as needing a resync to the device when
we need to do that automatically.
- Support for querying the size and stride of the register map,
allowing higher level frameworks to configure themselves more
readily.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJViTT4AAoJECTWi3JdVIfQkXUH/2M7hKIAZ+OiZYFMW1SNupDv
YQ5h6F/lQAWs06AD3nuKgKLZQOdbTVthdYl05DretT+JMIJIyW3QeOrdiEdVTzcU
zX5tcfg8wWW1/VmtT9YZQ7uhgJZ3+Sbirt2KZdEag2LTqMtItqJFRyjIr5CwvQff
eQSdvUnygmQPktvqYc0S2CN0DsJt5YCRlg+AC624WGdt7VJadWkSLNwR+cELSpRy
F+ok1+bdy7RdqYtt7CrwCiZgvv8yCYgvuHFUkTMg5/qkUj3ps/dnj0DV80m/Dqig
IUccwDscWjiRLKYtS6UM9bGMlADFAdnp/WSzAr6iiEaWVSGfb6h2agKdYO35qHE=
=0JUa
-----END PGP SIGNATURE-----
Merge tag 'regmap-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"As well as a few fixes and updates for API changes there's two new
features for the API:
- Better support for handling a reset of the underlying hardware,
marking the register map as needing a resync to the device when we
need to do that automatically
- Support for querying the size and stride of the register map,
allowing higher level frameworks to configure themselves more
readily"
* tag 'regmap-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Fix possible shift overflow in regmap_field_init()
regmap: Fix regmap_bulk_read in BE mode
regmap: kill off set_irq_flags usage
regmap: irq: Fixed a typo error
regmap: drop unneeded goto
regmap: Introduce regmap_get_reg_stride
regmap: Introduce regmap_get_max_register
regmap: Use regcache_mark_dirty() to indicate power loss or reset
regmap: Add a helper function for regcache sync test
regmap: Constify irq_domain_ops
