Since commit dccd2304cc ("ARM: 7430/1: sizes.h: move from asm-generic
to <linux/sizes.h>"), <asm/sizes.h> and <asm-generic/sizes.h> are just
wrappers of <linux/sizes.h>.
This commit replaces all <asm/sizes.h> and <asm-generic/sizes.h> to
prepare for the removal.
Link: http://lkml.kernel.org/r/1553267665-27228-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to request dynamic allocationn of GPIO IDs, a negative number
should be passed as a base GPIO ID via platform data. Unfortuntely,
commit 771e53c4d1 ("ARM: OMAP1: ams-delta: Drop board specific global
GPIO numbers") didn't follow that rule while switching to dynamically
allocated GPIO IDs for Amstrad Delta latches, making their IDs
overlapping with those already assigned to OMAP GPIO devices. Fix it.
Fixes: 771e53c4d1 ("ARM: OMAP1: ams-delta: Drop board specific global GPIO numbers")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: stable@vger.kernel.org
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull i2c updates from Wolfram Sang:
- the I2C core gained helpers to assist drivers in handling their
suspended state, and drivers were converted to use it
- two new fault-injectors for stress-testing
- bigger refactoring and feature improvements for the ocores,
sh_mobile, and tegra drivers
- platform_data removal for the at24 EEPROM driver
- ... and various improvements and bugfixes all over the subsystem
* 'i2c/for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (69 commits)
i2c: Allow recovery of the initial IRQ by an I2C client device.
i2c: ocores: turn incomplete kdoc into a comment
i2c: designware: Do not allow i2c_dw_xfer() calls while suspended
i2c: tegra: Only display error messages if DMA setup fails
i2c: gpio: fault-injector: add 'inject_panic' injector
i2c: gpio: fault-injector: add 'lose_arbitration' injector
i2c: tegra: remove multi-master support
i2c: tegra: remove master fifo support on tegra186
i2c: tegra: change phrasing, "fallbacking" to "falling back"
i2c: expand minor range when registering chrdev region
i2c: aspeed: Add multi-master use case support
i2c: core-smbus: don't trace smbus_reply data on errors
i2c: ocores: Add support for bus clock via platform data
i2c: ocores: Add support for IO mapper registers.
i2c: ocores: checkpatch fixes
i2c: ocores: add SPDX tag
i2c: ocores: add polling interface
i2c: ocores: do not handle IRQ if IF is not set
i2c: ocores: stop transfer on timeout
i2c: tegra: add i2c interface timing support
...
This augments the CBUS GPIO I2C driver to use GPIO
descriptors for clock, sel and data. We drop the platform
data that was only used for carrying GPIO numbers and
use machine descriptor tables instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This pushes the handling of inversion semantics and open drain
settings to the GPIO descriptor and gpiolib. All affected board
files are also augmented.
This is especially nice since we don't have to have any
confusing flags passed around to the left and right littering
the fixed and GPIO regulator drivers and the regulator core.
It is all just very straight-forward: the core asks the GPIO
line to be asserted or deasserted and gpiolib deals with the
rest depending on how the platform is configured: if the line
is active low, it deals with that, if the line is open drain,
it deals with that too.
Cc: Alexander Shiyan <shc_work@mail.ru> # i.MX boards user
Cc: Haojian Zhuang <haojian.zhuang@gmail.com> # MMP2 maintainer
Cc: Aaro Koskinen <aaro.koskinen@iki.fi> # OMAP1 maintainer
Cc: Tony Lindgren <tony@atomide.com> # OMAP1,2,3 maintainer
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> # EM-X270 maintainer
Cc: Robert Jarzmik <robert.jarzmik@free.fr> # EZX maintainer
Cc: Philipp Zabel <philipp.zabel@gmail.com> # Magician maintainer
Cc: Petr Cvek <petr.cvek@tul.cz> # Magician
Cc: Robert Jarzmik <robert.jarzmik@free.fr> # PXA
Cc: Paul Parsons <lost.distance@yahoo.com> # hx4700
Cc: Daniel Mack <zonque@gmail.com> # Raumfeld maintainer
Cc: Marc Zyngier <marc.zyngier@arm.com> # Zeus maintainer
Cc: Geert Uytterhoeven <geert+renesas@glider.be> # SuperH pinctrl/GPIO maintainer
Cc: Russell King <rmk+kernel@armlinux.org.uk> # SA1100
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> #OMAP1 Amstrad Delta
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
SoC updates, mostly refactorings and cleanups of old legacy platforms,
but also a few more things:
New SoC support this release:
- NXP/Freescale i.MX7ULP (1x Cortex-A7, Cortex-M4, graphics, etc)
- Allwinner F1C100, older platform with an ARM926-EJS (ARMv5) core
Cleanups of various platforms:
- OMAP1 ams-delta does some GPIO cleanups
- Davinci removes of at24 platform data
- Samsung cleans up old wakeup, PM debug and secondary core boot code
- Renesas moves around config options and PM code to drivers/soc for
sharing with 64-bit and more consistency
- i.MX, Broadcom and SoCFPGA all have tweaks to lowlevel debug console setups
- SoCFPGA adds explicit selection of ARM errata and removes some unused code
This tag also contains a few patches that I had queued up as fixes for
4.20 but didn't send in before the release.
-----BEGIN PGP SIGNATURE-----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=m7me
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm SoC platform updates from Olof Johansson:
"SoC updates, mostly refactorings and cleanups of old legacy platforms,
but also a few more things:
New SoC support this release:
- NXP/Freescale i.MX7ULP (1x Cortex-A7, Cortex-M4, graphics, etc)
- Allwinner F1C100, older platform with an ARM926-EJS (ARMv5) core
Cleanups of various platforms:
- OMAP1 ams-delta does some GPIO cleanups
- Davinci removes of at24 platform data
- Samsung cleans up old wakeup, PM debug and secondary core boot code
- Renesas moves around config options and PM code to drivers/soc for
sharing with 64-bit and more consistency
- i.MX, Broadcom and SoCFPGA all have tweaks to lowlevel debug
console setups
- SoCFPGA adds explicit selection of ARM errata and removes some
unused code
This also contains a few patches that I had queued up as fixes for
4.20 but didn't send in before the release"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (68 commits)
arm64: dts: renesas: draak: Fix CVBS input
ARM: omap2: avoid section mismatch warning
ARM: tegra: avoid section mismatch warning
ARM: ks8695: fix section mismatch warning
ARM: pxa: avoid section mismatch warning
ARM: mmp: fix pxa168_device_usb_phy use on aspenite
ARM: mmp: fix timer_init calls
ARM: OMAP1: fix USB configuration for device-only setups
ARM: OMAP1: add MMC configuration for Palm Tungsten E
ARM: imx: fix dependencies on imx7ulp
ARM: meson: select HAVE_ARM_TWD and ARM_GLOBAL_TIMER
MAINTAINERS: add drivers/soc/amlogic/ to amlogic list
ARM: imx: add initial support for imx7ulp
ARM: debug-imx: only define DEBUG_IMX_UART_PORT if needed
ARM: dts: Fix OMAP4430 SDP Ethernet startup
ARM: dts: am335x-pdu001: Fix polarity of card detection input
ARM: OMAP1: ams-delta: Fix audio permanently muted
ARM: dts: omap5: Fix dual-role mode on Super-Speed port
arm64: dts: rockchip: fix rk3399-rockpro64 regulator gpios
ARM: davinci: da850-evm: remove unnecessary include
...
Merge in fixes here, since the last batch didn't make it in before the
release of 4.20, and we might as well group them with this set of
patches.
* fixes: (822 commits)
arm64: dts: renesas: draak: Fix CVBS input
ARM: dts: Fix OMAP4430 SDP Ethernet startup
ARM: dts: am335x-pdu001: Fix polarity of card detection input
ARM: OMAP1: ams-delta: Fix audio permanently muted
ARM: dts: omap5: Fix dual-role mode on Super-Speed port
arm64: dts: rockchip: fix rk3399-rockpro64 regulator gpios
ARM: dts: imx7d-nitrogen7: Fix the description of the Wifi clock
ARM: imx: update the cpu power up timing setting on i.mx6sx
Revert "arm64: dts: marvell: add CPU Idle power state support on Armada 7K/8K"
ARM: dts: imx7d-pico: Describe the Wifi clock
ARM: dts: realview: Fix some more duplicate regulator nodes
MAINTAINERS: update entry for MMP platform
ARM: mmp/mmp2: fix cpu_is_mmp2() on mmp2-dt
MAINTAINERS: mediatek: Update SoC entry
ARM: dts: bcm2837: Fix polarity of wifi reset GPIOs
+ Linux 4.20-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
Core changes:
- Some core changes are already in outside of this pull
request as they came through the regulator tree, most
notably devm_gpiod_unhinge() that removes devres refcount
management from a GPIO descriptor. This is needed in
subsystems such as regulators where the regulator core
need to take over the reference counting and lifecycle
management for a GPIO descriptor.
- We dropped devm_gpiochip_remove() and devm_gpio_chip_match()
as nothing needs it. We can bring it back if need be.
- Add a global TODO so people see where we are going. This
helps setting the direction now that we are two GPIO
maintainers.
- Handle the MMC CD/WP properties in the device tree core.
(The bulk of patches activating this code is already
merged through the MMC/SD tree.)
- Augment gpiochip_request_own_desc() to pass a flag so
we as gpiochips can request lines as active low or open
drain etc even from ourselves.
New drivers:
- New driver for Cadence GPIO blocks.
- New driver for Atmel SAMA5D2 PIOBU GPIO lines.
Driver improvements:
- A major refactoring of the PCA953x driver - this driver has
been around for ages, and is now modernized to reduce code
duplication that has stacked up and is using regmap to read
write and cache registers.
- Intel drivers are now maintained in a separate tree and
start with a round of cleanups and unifications.
-----BEGIN PGP SIGNATURE-----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=05LW
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.21 kernel series.
Core changes:
- Some core changes are already in outside of this pull request as
they came through the regulator tree, most notably
devm_gpiod_unhinge() that removes devres refcount management from a
GPIO descriptor. This is needed in subsystems such as regulators
where the regulator core need to take over the reference counting
and lifecycle management for a GPIO descriptor.
- We dropped devm_gpiochip_remove() and devm_gpio_chip_match() as
nothing needs it. We can bring it back if need be.
- Add a global TODO so people see where we are going. This helps
setting the direction now that we are two GPIO maintainers.
- Handle the MMC CD/WP properties in the device tree core. (The bulk
of patches activating this code is already merged through the
MMC/SD tree.)
- Augment gpiochip_request_own_desc() to pass a flag so we as
gpiochips can request lines as active low or open drain etc even
from ourselves.
New drivers:
- New driver for Cadence GPIO blocks.
- New driver for Atmel SAMA5D2 PIOBU GPIO lines.
Driver improvements:
- A major refactoring of the PCA953x driver - this driver has been
around for ages, and is now modernized to reduce code duplication
that has stacked up and is using regmap to read write and cache
registers.
- Intel drivers are now maintained in a separate tree and start with
a round of cleanups and unifications"
* tag 'gpio-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (99 commits)
gpio: sama5d2-piobu: Depend on OF_GPIO
gpio: Add Cadence GPIO driver
dt-bindings: gpio: Add bindings for Cadence GPIO
gpiolib-acpi: remove unused variable 'err', cleans up build warning
gpio: mxs: read pin level directly instead of using .get
gpio: aspeed: remove duplicated statement
gpio: add driver for SAMA5D2 PIOBU pins
dt-bindings: arm: atmel: describe SECUMOD usage as a GPIO controller
gpio/mmc/of: Respect polarity in the device tree
dt-bindings: gpio: rcar: Add r8a774c0 (RZ/G2E) support
memory: omap-gpmc: Get the header of the enum
ARM: omap1: Fix new user of gpiochip_request_own_desc()
gpio: pca953x: Add regmap dependency for PCA953x driver
gpio: raspberrypi-exp: decrease refcount on firmware dt node
gpiolib: Fix return value of gpio_to_desc() stub if !GPIOLIB
gpio: pca953x: Restore registers after suspend/resume cycle
gpio: pca953x: Zap single use of pca953x_read_single()
gpio: pca953x: Zap ad-hoc reg_output cache
gpio: pca953x: Zap ad-hoc reg_direction cache
gpio: pca953x: Perform basic regmap conversion
...
There are no intensive changes in both ALSA and ASoC core parts while
rather most of changes are a bunch of driver fixes and updates.
A large diff pattern appears in ASoC TI part which now merges both
OMAP and DaVinci stuff, but the rest spreads allover the places.
Note that this pull request includes also some updates for LED trigger
and platform drivers for mute LEDs, appearing in the diffstat as well.
Some highlights:
ASoC:
- Preparatory work for merging the audio-graph and audio-graph-scu
cards
- A merge of TI OMAP and DaVinci directories, as both product lines
get merged together. Also including a few architecture changes as
well.
- Major cleanups of the Maxim MAX9867 driver
- Small fixes for tablets & co with Intel BYT/CHT chips
- Lots of rsnd updates as usual
- Support for Asahi Kaesi AKM4118, AMD ACP3x, Intel platforms with
RT5660, Meson AXG S/PDIF inputs, several Qualcomm IPs and Xilinx I2S
controllers
HD-audio:
- Introduce audio-mute LED trigger for replacing the former hackish
dynamic binding
- Huawei WMI hotkey and mute LED support
- Refactoring of PM code and display power controls
- Headset button support in the generic jack code
- A few updates for Tegra
- Fixups for HP EliteBook and ASUS UX391UA
- Lots of updates for Intel ASoC HD-audio, including the improved DSP
detection and the fallback binding from ASoC SST to legacy HD-audio
controller drivers
Others:
- Updates for FireWire TASCAM and Fireface devices, some other fixes
- A few potential Spectre v1 fixes that are all trivial
-----BEGIN PGP SIGNATURE-----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=SG61
-----END PGP SIGNATURE-----
Merge tag 'sound-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"There are no intensive changes in both ALSA and ASoC core parts while
rather most of changes are a bunch of driver fixes and updates. A
large diff pattern appears in ASoC TI part which now merges both OMAP
and DaVinci stuff, but the rest spreads allover the places.
Note that this pull request includes also some updates for LED trigger
and platform drivers for mute LEDs, appearing in the diffstat as well.
Some highlights:
ASoC:
- Preparatory work for merging the audio-graph and audio-graph-scu
cards
- A merge of TI OMAP and DaVinci directories, as both product lines
get merged together. Also including a few architecture changes as
well.
- Major cleanups of the Maxim MAX9867 driver
- Small fixes for tablets & co with Intel BYT/CHT chips
- Lots of rsnd updates as usual
- Support for Asahi Kaesi AKM4118, AMD ACP3x, Intel platforms with
RT5660, Meson AXG S/PDIF inputs, several Qualcomm IPs and Xilinx
I2S controllers
HD-audio:
- Introduce audio-mute LED trigger for replacing the former hackish
dynamic binding
- Huawei WMI hotkey and mute LED support
- Refactoring of PM code and display power controls
- Headset button support in the generic jack code
- A few updates for Tegra
- Fixups for HP EliteBook and ASUS UX391UA
- Lots of updates for Intel ASoC HD-audio, including the improved DSP
detection and the fallback binding from ASoC SST to legacy HD-audio
controller drivers
Others:
- Updates for FireWire TASCAM and Fireface devices, some other fixes
- A few potential Spectre v1 fixes that are all trivial"
* tag 'sound-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (280 commits)
ALSA: HD-Audio: SKL+: force HDaudio legacy or SKL+ driver selection
ALSA: HD-Audio: SKL+: abort probe if DSP is present and Skylake driver selected
ALSA: HDA: export process_unsol_events()
ALSA: hda/realtek: Enable audio jacks of ASUS UX391UA with ALC294
ALSA: bebob: fix model-id of unit for Apogee Ensemble
ALSA: emu10k1: Fix potential Spectre v1 vulnerabilities
ALSA: rme9652: Fix potential Spectre v1 vulnerability
ASoC: ti: Kconfig: Remove the deprecated options
ARM: davinci_all_defconfig: Update the audio options
ARM: omap1_defconfig: Do not select ASoC by default
ARM: omap2plus_defconfig: Update the audio options
ARM: davinci: dm365-evm: Update for the new ASoC Kcofnig options
ARM: OMAP2: Update for new MCBSP Kconfig option
ARM: OMAP1: Makefile: Update for new MCBSP Kconfig option
MAINTAINERS: Add entry for sound/soc/ti and update the OMAP audio support
ASoC: ti: Merge davinci and omap directories
ALSA: hda: add mute LED support for HP EliteBook 840 G4
ALSA: fireface: code refactoring to handle model-specific registers
ALSA: fireface: add support for packet streaming on Fireface 800
ALSA: fireface: allocate isochronous resources in mode-specific implementation
...
- Parse the 4BAIT SFDP section
- Add a bunch of SPI NOR entries to the flash_info table
- Add the concept of SFDP fixups and use it to fix a bug on MX25L25635F
- A bunch of minor cleanups/comestic changes
-----BEGIN PGP SIGNATURE-----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=JXhP
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-4.21' of git://git.infradead.org/linux-mtd into mtd/next
Core changes:
- Parse the 4BAIT SFDP section
- Add a bunch of SPI NOR entries to the flash_info table
- Add the concept of SFDP fixups and use it to fix a bug on MX25L25635F
- A bunch of minor cleanups/comestic changes
The MCBSP config option has been changed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes up a new user of gpiochip_request_own_desc() in
the AMS Delta board that appeared after the patch that was
applied recently.
Fixes: 21abf10381 ("gpio: Pass a flag to gpiochip_request_own_desc()")
Reviewed-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Before things go out of hand, make it possible to pass
flags when requesting "own" descriptors from a gpio_chip.
This is necessary if the chip wants to request a GPIO with
active low semantics, for example.
Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Roger Quadros <rogerq@ti.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently we do USB configuration only if the host mode (CONFIG_USB)
is enabled. But it should be done also in the case of device-only setups,
so change the condition to CONFIG_USB_SUPPORT. This allows to use
omap_udc on Palm Tungsten E.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add initial MMC configuration for Palm Tungsten E to allow using a proper
rootfs on the device. This still assumes the bootloader enabling the MMC,
and that the card is always present and writeable.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since commit 1137ceee76 ("ARM: OMAP1: ams-delta: Don't request unused
GPIOs"), on-board audio has appeared muted. Believed to be unused GPIO
pin "hookflash1", apparently set high regardless of the corresponding
bit of "latch2" port attempted to be set low during .init_machine(),
has been identified as the reason.
According to Amstrad E3 wiki, the purpose of the pin hasn't been
clearly identified. Original Amstrad software used to produce a high
pulse on it when the phone was taken off hook or recall was pressed.
With the current finding, we can assume the pin provides a kind of
audio mute function.
Proper resolution of the issue should be done in two steps:
- resolution of an issue with the pin state not reflecting the value
the corresponding bit of the port was attempted to be initialized
with,
- extension of on-board audio driver with a new control.
For now, rename the pin to "audio_mute" to reflect its function and,
as a quick fix, hogg it as output low so on-board audio can produce
audible sound again.
Fixes: 1137ceee76 ("ARM: OMAP1: ams-delta: Don't request unused GPIOs")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Amstrad Delta NAND driver now uses GPIO API for data I/O so there is no
need to assign memory I/O resource to the device any longer. Drop it.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Data port used by Amstrad Delta NAND driver is actually an OMAP MPUIO
device, already under control of gpio-omap driver. The NAND driver
gets access to the port by ioremapping it and performs read/write
operations. That is done without any proteciton from other users
legally manipulating the port pins over GPIO API.
The plan is to convert the driver to access the port over GPIO consumer
API. Before that is implemented, the driver can already obtain
exclusive access to the port by requesting an array of its GPIO
descriptors.
Add respective entries to the NAND GPIO lookup table.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Configure omap1_spi100k only on OMAP7xx. This allows running multiboard
kernels on non-OMAP7xx HW with CONFIG_SPI_OMAP_100K enabled.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently we get extra newlines on OMAP1/2 when the SoC name is printed:
[ 0.000000] OMAP1510
[ 0.000000] revision 2 handled as 15xx id: bc058c9b93111a16
[ 0.000000] OMAP2420
[ 0.000000]
Fix by using pr_cont.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
That symbol is not used outside the board file, there is no need to
keep it in the board header.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Those bitmap symbols defining pins of latch2 register, used with
read()/write() calls before the latch was converted to a GPIO device,
have been obsoleted by integer symbols defined inside the board file.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As all users of the board specific GPIO pins have been converted from
legacy integer-based to descriptor-based interface, there is no longer
a need to maintain statically assigned GPIO pin numbers. Drop support
for that.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Global GPIO numbers no longer have to be passed to leds-gpio driver,
replace their assignment with a lookup table.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now as the board header file is no longer included by drivers, move it
to the root directory of mach-omap1.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
While playing with initialization order of modem device, it has been
discovered that under some circumstances (early console init, I
believe) its .pm() callback may be called before the
uart_port->private_data pointer is initialized from
plat_serial8250_port->private_data, resulting in NULL pointer
dereference. Fix it by checking for uninitialized pointer before using
it in modem_pm().
Fixes: aabf31737a ("ARM: OMAP1: ams-delta: update the modem to use regulator API")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to use IRQ_NOTCONNECTED instead of -EINVAL for
ams_delta_modem_ports irq.
-----BEGIN PGP SIGNATURE-----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=SgVo
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.20/omap1-fix-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fix for omap1 ams-delta irq
We need to use IRQ_NOTCONNECTED instead of -EINVAL for
ams_delta_modem_ports irq.
* tag 'omap-for-v4.20/omap1-fix-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP1: ams-delta: Fix impossible .irq < 0
Signed-off-by: Olof Johansson <olof@lixom.net>
A couple of platforms change hands in the MAINTAINERS file:
- Linus Walleij lists himself for the ARM Reference platforms:
versatile, vexpress, integrator and realview. He has been the main
contributor for these for a while, and makes it official now.
- Vladimir Zapolskiy takes over the LPC18xx platform from Joachim Eastwood
- Manivannan Sadhasivam becomes a secondary maintainer for the
Actions Semi machines
- Nicolas Ferre lists updates the MAINTAINER listing for the AT91
platform: Ludovic Desroches is now a co-maintainer for the platform, and
several other people (Claudiu Beznea, Cristian Birsan, Eugen Hristev,
Codrin Ciubotariu) take over individual device drivers.
Thanks everyone for working on this, and welcome to the new maintainers!
The "virt" platform on qemy or kvm can now be used in big-endian mode
without additional tricks, thanks to Jason Donenfeld.
Once again, we gain support for another NXP i.MX6 variant, this time
it's the i.MX 6ULZ 32-bit single-core version.
On arm64, we add support for two SoCs from Renesas: RZ/G2E (r8a774c0)
and RZ/G2M (r8a774a1). These are described as microcontrollers on the
manufacturer website, but appear to be rather powerful. The RZ/G2M is
used on the reference board for the CIP Super Long Term Support (SLTS)
Linux Kernels.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7+46
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"A couple of platforms change hands in the MAINTAINERS file:
- Linus Walleij lists himself for the ARM Reference platforms:
versatile, vexpress, integrator and realview. He has been the main
contributor for these for a while, and makes it official now.
- Vladimir Zapolskiy takes over the LPC18xx platform from Joachim
Eastwood
- Manivannan Sadhasivam becomes a secondary maintainer for the
Actions Semi machines
- Nicolas Ferre lists updates the MAINTAINER listing for the AT91
platform: Ludovic Desroches is now a co-maintainer for the
platform, and several other people (Claudiu Beznea, Cristian
Birsan, Eugen Hristev, Codrin Ciubotariu) take over individual
device drivers.
Thanks everyone for working on this, and welcome to the new
maintainers!
The "virt" platform on qemy or kvm can now be used in big-endian mode
without additional tricks, thanks to Jason Donenfeld.
Once again, we gain support for another NXP i.MX6 variant, this time
it's the i.MX 6ULZ 32-bit single-core version.
On arm64, we add support for two SoCs from Renesas: RZ/G2E (r8a774c0)
and RZ/G2M (r8a774a1). These are described as microcontrollers on the
manufacturer website, but appear to be rather powerful. The RZ/G2M is
used on the reference board for the CIP Super Long Term Support (SLTS)
Linux Kernels"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
MAINTAINERS: Assign myself as a maintainer of ARM/LPC18XX architecture
arm64: exynos: Enable generic power domain support
MAINTAINERS: remove non-exsiting email address of Baoyou
MAINTAINERS: fix pattern in ARM/Synaptics berlin SoC section
MAINTAINERS: Drop dt-bindings/genpd/k2g.h
ARM: samsung: Limit SAMSUNG_PM_CHECK config option to non-Exynos platforms
arm64: actions: Enable PINCTRL in platforms Kconfig
MAINTAINERS: Add entry for Actions Semi Owl SoCs DMA driver
MAINTAINERS: Add entry for Actions Semiconductor Owl I2C driver
MAINTAINERS: Update clock binding entry for Actions Semi Owl SoCs
ARM: imx: add i.mx6ulz msl support
ARM: Assume maintainership of ARM reference designs
ARM: support big-endian for the virt architecture
MAINTAINERS: sdhci: move the Microchip entry to proper location
MAINTAINERS: move former ATMEL entries to proper MICROCHIP location
MAINTAINERS: remove the / ATMEL string from MICROCHIP entries
MAINTAINERS: iio: add co-maintainer to SAMA5D2-compatible ADC driver
MAINTAINERS: pwm: add entry for Microchip pwm driver
MAINTAINERS: dmaengine: add files to Microchip dma entry
MAINTAINERS: USB: change maintainer for Microchip USBA gadget driver
...
The biggest chunk of the regulator changes for this release outside of
the new drivers is the conversion of the fixed regulator to use the GPIO
descriptor API, there's a small addition to the GPIO API plus a bunch of
updates to board files to implement it. This is some really welcome
work from Linus Walleij that's had a bunch of review and has been
sitting in -next for a while so I'm fairly happy there's no major
issues.
- Helpers for overlapping linear ranges.
- Display opmode and consumer requested load in the regualtor_summary
file in debugfs, plus a fix there.
- Support for the fun and entertaining power off mechanism that the
pfuze100 hardware implements.
- Conversion of the fixed regulator API to use GPIO descriptors,
including pulling in a bunch of patches to a bunch of board files.
- New drivers for Cirrus Logic Lochnagar, Qualcomm PMS405, Rohm
BD71847, ST PMIC1, and TI LM363x devices.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlvNyl0THGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0DubB/4nWL/XSUb7qIm2fjjMUffelfk4/viB
MZg3JPEMr7ahK+QC1RQ5nOmkuACSU3Uij8RE1omLp5isfCiSa+e17f9uQx4Cn/pw
9DsIeJUEC4LvZ9gA9pDf0313B/0BIYfOMJToyLgwTNmJl+T+0e59RcS4TTCEqxwD
PmpPakOvCTD6YuVI7HhYL/HXJK1buvrAiENSjCyfyJTDaMSzJl6WMn+eibFaZbDn
NXwj2W+QyuiFCdl/7/4NWaqhlyOvM05ivnnLM/SPMBj+Iu4gSZ0PX81z98eZ3M66
YSPhF2o5SkhhffFx5xjpgR3VquXDVb0oefzhvJmZYHXi7ZKKMruoYaGB
=Ztu3
-----END PGP SIGNATURE-----
Merge tag 'regulator-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"The biggest chunk of the regulator changes for this release outside of
the new drivers is the conversion of the fixed regulator to use the
GPIO descriptor API, there's a small addition to the GPIO API plus a
bunch of updates to board files to implement it. This is some really
welcome work from Linus Walleij that's had a bunch of review and has
been sitting in -next for a while so I'm fairly happy there's no major
issues.
- Helpers for overlapping linear ranges.
- Display opmode and consumer requested load in the regualtor_summary
file in debugfs, plus a fix there.
- Support for the fun and entertaining power off mechanism that the
pfuze100 hardware implements.
- Conversion of the fixed regulator API to use GPIO descriptors,
including pulling in a bunch of patches to a bunch of board files.
- New drivers for Cirrus Logic Lochnagar, Qualcomm PMS405, Rohm
BD71847, ST PMIC1, and TI LM363x devices"
* tag 'regulator-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (36 commits)
regulator: lochnagar: Use a consisent comment style for SPDX header
regulator: bd718x7: Remove struct bd718xx_pmic
regulator: Fetch enable gpiods nonexclusive
regulator/gpio: Allow nonexclusive GPIO access
regulator: lochnagar: Add support for the Cirrus Logic Lochnagar
regulator: stpmic1: Return REGULATOR_MODE_INVALID for invalid mode
regulator: stpmic1: add stpmic1 regulator driver
dt-bindings: regulator: document stpmic1 pmic regulators
regulator: axp20x: Mark expected switch fall-throughs
regulator: bd718xx: fix build warning on x86_64
regulator: fixed: Default enable high on DT regulators
regulator: bd718xx: rename bd71837 to 718xx
regulator: bd718XX use pickable ranges
regulator/mfd: bd718xx: rename bd71837/bd71847 common instances
regulator: Support regulators where voltage ranges are selectable
mfd: dt bindings: add BD71847 device-tree binding documentation
regulator: dt bindings: add BD71847 device-tree binding documentation
regulator/mfd: Support ROHM BD71847 power management IC
regulator: da905{2,5}: Remove unnecessary array check
regulator: qcom: Add PMS405 regulators
...
Since the very beginning, unsigned int .irq member of struct
plat_serial8250_port introduced by commit eff443df67 ("OMAP1:
AMS_DELTA: add modem support") was statically initialized to a negative
value -EINVAL. Moreover, commit 0812db9437 ("ARM: OMAP1: ams-delta:
assign MODEM IRQ from GPIO descriptor") has introduced some new code
which checks for that member carrying a negative value which is
impossible.
Use IRQ_NOTCONNECTED instead of -EINVAL. Also, drop the valueless check
and let the modem device be registered regardless of .irq value, and
the value handled by "serial8250" driver.
Fixes: 0812db9437 ("ARM: OMAP1: ams-delta: assign MODEM IRQ from GPIO descriptor")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
platform_nand_xxx definitions are just used by the plat_nand driver.
Let's move those definitions out of the core/driver-agnostic rawnand.h
header.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We regularly have new NAND controller drivers that are making use of
fields/hooks that we want to get rid of but can't because of all the
legacy drivers that we might break if we do.
So, instead of removing those fields/hooks, let's move them to a
sub-struct which is clearly documented as deprecated.
We start with the ->IO_ADDR_{R,W] fields.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
In order to do that, we first need to update the platform_nand_ctrl
hooks to take a nand_chip object instead of an mtd_info.
We add temporary plat_nand_xxx() wrappers to the do the mtd -> chip
conversion, but those will be dropped when patching nand_chip hooks to
take a nand_chip object.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
GPIOs with no kernel drivers can still be used from user space, don't
request them from the board file.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Instead of defining symbols already defined in
linux/platform_data/gpio-omap.h, use that header file.
Since we include the header into an assembler code, prevent C only bits
from being read in.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Amstrad Delta MODEM device used to be initialized at arch_initcall
before it was once moved to late_initcall by commit f7519d8c82 ("ARM:
OMAP1: ams-delta: register latch dependent devices later"). The purpose
of that change was to postpone initialization of devices which depended
on latch2 pins until latch2 converted to GPIO device was ready.
After recent fixes to GPIO handling, it was possible to moove
registration of most of those device back to where they were before.
The same can be safely done with the MODEM device as initialization
of GPIO pins it depends on was moved to machine_init by preceding
patch.
Move registration of the MODEM device to arch_initcall_sync, not to
arch_initcall, so it is never exposed to potential conflict in
registration order hazard against OMAP serial ports.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Latch2 pins control a number of on-board devices, namely LCD, NAND,
MODEM and CODEC. Those pins used to be initialized with safe values
from init_machine before that operation was:
1) moved to late_initcall in preparation for conversion of latch2 to
GPIO device - see commit f7519d8c82 ("ARM: OMAP1: ams-delta: register
latch dependent devices later"),
2) replaced with non-atomic initialization performed by means of
gpio_request_array() - see commit 937eb4bb00 ("ARM: OMAP1: ams-delta:
convert latches to basic_mmio_gpio"),
3) made completely asynchronous by delegation of GPIO request
operations performed on subsets of pins to respective device drivers in
subsequent commits.
One visible negative result of that disintegration was corrupt keyboard
data reported by serio driver, recently fixed by commit 41f8fee385
("ARM: OMAP1: ams-delta: Hog "keybrd_dataout" GPIO pin").
Moreover, initialization of LATCH2_PIN_MODEM_CODEC still performed with
ams_delta_latch2_write() wrapper from late_init() is now done on not
requested GPIO pin.
Reintroduce atomic initialization of latch2 pins at machine_init to
prevent from random values potentially corrupting NAND data or maybe
even destroing other hardware. Also take care of MODEM/CODEC related
pins so MODEM device probe succeeds even if latch2 GPIO device or
dependent regulator is not ready and CODEC can be reached over the
MODEM even if audio driver doesn't take control over
LATCH2_PIN_MODEM_CODEC.
Once done, remove the no longer needed GPIO based implementation of
ams_delta_latch_write() and its frontend macro.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[tony@atomide.com: updated for the header location to remove dependency]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Don't request MODEM IRQ GPIO by its global number in
ams_delta_modem_init(). Instead, obtain its GPIO descriptor
and assign related IRQ to the MODEM. Do that from
omap_gpio_deps_init(), where the chip is already looked up. Then, in
ams_delta_modem_init(), just check for the IRQ number having been
already assigned.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As we augmented the regulator core to accept a GPIO descriptor instead
of a GPIO number, we can augment the fixed GPIO regulator to look up
and pass that descriptor directly from device tree or board GPIO
descriptor look up tables.
Some boards just auto-enumerate their fixed regulator platform devices
and I have assumed they get names like "fixed-regulator.0" but it's
pretty hard to guess this. I need some testing from board maintainers to
be sure. Other boards are straight forward, using just plain
"fixed-regulator" (ID -1) or "fixed-regulator.1" hammering down the
device ID.
It seems the da9055 and da9211 has never got around to actually passing
any enable gpio into its platform data (not the in-tree code anyway) so we
can just decide to simply pass a descriptor instead.
The fixed GPIO-controlled regulator in mach-pxa/ezx.c was confusingly named
"*_dummy_supply_device" while it is a very real device backed by a GPIO
line. There is nothing dummy about it at all, so I renamed it with the
infix *_regulator_* as part of this patch set.
Intel MID portions tested by Andy.
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # Check the x86 BCM stuff
Acked-by: Tony Lindgren <tony@atomide.com> # OMAP1,2,3 maintainer
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Initialization of several Amstrad Delta devices was once moved to
late_initcall by commit f7519d8c82 ("ARM: OMAP1: ams-delta: register
latch dependent devices later"). The purpose of that move was to allow
smooth conversion of Amstrad Delta latches to GPIO.
After successful conversion only ams_delta_serio driver was moved back
to device_initcall by commit 8d09a1bb31 ("input: serio: ams-delta:
toggle keyboard power over GPIO"). Registration of ams-delta-nand and
lcd_ams_delta devices was kept in late_initcall in order to avoid
corrupt data reported by the serio driver on boot. Registration of
cx20442-codec device was kept there for it to be probed after a
regulator on which it depended was ready.
The issue of "keybrd_dataout" GPIO pin not initilized to GPIO_OUT_LOW
before other latch2 pins causing the corruption have been apparently
fixed by commit 5322c19b117a ("ARM: OMAP1: ams-delta: Hog
"keybrd_dataout" GPIO pin"). In turn, the issue of missing regulator
has been fixed by commit 50c678772a ("ASoC: cx20442: Don't ignore
regulator_get() errors.").
Simplify the board init code by moving registration of those devices
back to init_machine.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Instead of exporting the FIQ buffer symbol to be used in
ams-delta-serio driver, pass it to the driver as platform_data.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The driver still obtains IRQ number from a hardcoded GPIO. Use IRQ
resource instead.
For this to work on Amstrad Delta, add the IRQ resource to
ams-delta-serio platform device structure. Obtain the IRQ number
assigned to "keybrd_clk" GPIO pin from FIQ initialization routine.
As a benefit, the driver no longer needs to include
<mach/board-ams-delta.h>.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Split the header file into two parts and move them to directories where
they belong.
Information on internal structure of FIQ buffer is moved to
<linux/platform_data/ams-delta-fiq.h> for ams-delta-serio driver use.
Other information used by ams-delta board init file and FIQ code is
made local to mach-omap1 root directory.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
From the very beginning, input GPIO pins of ams-delta serio port have
been used by FIQ handler, not serio driver.
Don't request those pins from the ams-delta-serio driver any longer,
instead keep them requested and initialized by the FIQ initialization
routine which already requests them and releases while identifying GPIO
IRQs.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With introduction of GPIO lookup tables to Amstrad Delta board init
file, semantics of symbols representing OMAP GPIO pins defined in
<mach/board-ams-delta.h> changed from statically assigned global GPIO
numbers to hardware pin numbers local to OMAP "gpio-0-15" chip.
This patch modifies deferred FIQ interrupt handler so it no longer uses
static GPIO numbers in favour of IRQ data descriptors obtained at FIQ
initialization time from descriptor of the GPIO chip with use of its
hardware pin numbers. The chip descriptor is passed from the board
init file.
As a benefit, the deferred FIQ handler should work faster.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
[tony@atomide.com: removed duplicate gpiochip_match_by_label]
Signed-off-by: Tony Lindgren <tony@atomide.com>
