This patch fixes a bug reported by a customer, who found
that many unreasonable error interrupts reported on all
non-boot CPUs (APs) during the system boot stage.
According to Chapter 10 of Intel Software Developer Manual
Volume 3A, Local APIC may signal an illegal vector error when
an LVT entry is set as an illegal vector value (0~15) under
FIXED delivery mode (bits 8-11 is 0), regardless of whether
the mask bit is set or an interrupt actually happen. These
errors are seen as error interrupts.
The initial value of thermal LVT entries on all APs always reads
0x10000 because APs are woken up by BSP issuing INIT-SIPI-SIPI
sequence to them and LVT registers are reset to 0s except for
the mask bits which are set to 1s when APs receive INIT IPI.
When the BIOS takes over the thermal throttling interrupt,
the LVT thermal deliver mode should be SMI and it is required
from the kernel to keep AP's LVT thermal monitoring register
programmed as such as well.
This issue happens when BIOS does not take over thermal throttling
interrupt, AP's LVT thermal monitor register will be restored to
0x10000 which means vector 0 and fixed deliver mode, so all APs will
signal illegal vector error interrupts.
This patch check if interrupt delivery mode is not fixed mode before
restoring AP's LVT thermal monitor register.
Signed-off-by: Youquan Song <youquan.song@intel.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Yong Wang <yong.y.wang@intel.com>
Cc: hpa@linux.intel.com
Cc: joe@perches.com
Cc: jbaron@redhat.com
Cc: trenn@suse.de
Cc: kent.liu@intel.com
Cc: chaohong.guo@intel.com
Cc: <stable@kernel.org> # As far back as possible
Link: http://lkml.kernel.org/r/1303402963-17738-1-git-send-email-youquan.song@intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Convert x86 i8253 clocksource code to use generic i8253 clocksource.
Acked-by: John Stultz <john.stultz@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is a fix for the SGI Altix-UV Broadcast Assist Unit code,
which is used for TLB flushing.
Certain hardware configurations (that customers are ordering)
cause nasids (numa address space id's) to be non-consecutive.
Specifically, once you have more than 4 blades in a IRU
(Individual Rack Unit - or 1/2 rack) but less than the maximum
of 16, the nasid numbering becomes non-consecutive. This
currently results in a 'catastrophic error' (CATERR) detected by
the firmware during OS boot. The BAU is generating an 'INTD'
request that is targeting a non-existent nasid value. Such
configurations may also occur when a blade is configured off
because of hardware errors. (There is one UV hub per blade.)
This patch is required to support such configurations.
The problem with the tlb_uv.c code is that is using the
consecutive hub numbers as indices to the BAU distribution bit
map. These are simply the ordinal position of the hub or blade
within its partition. It should be using physical node numbers
(pnodes), which correspond to the physical nasid values. Use of
the hub number only works as long as the nasids in the partition
are consecutive and increase with a stride of 1.
This patch changes the index to be the pnode number, thus
allowing nasids to be non-consecutive.
It also provides a table in local memory for each cpu to
translate target cpu number to target pnode and nasid.
And it improves naming to properly reflect 'node' and 'uvhub'
versus 'nasid'.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/E1QJmxX-0002Mz-Fk@eag09.americas.sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Introduce a new x86_init hook called pagetable_reserve that at the end
of init_memory_mapping is used to reserve a range of memory addresses for
the kernel pagetable pages we used and free the other ones.
On native it just calls memblock_x86_reserve_range while on xen it also
takes care of setting the spare memory previously allocated
for kernel pagetable pages from RO to RW, so that it can be used for
other purposes.
A detailed explanation of the reason why this hook is needed follows.
As a consequence of the commit:
commit 4b239f458c
Author: Yinghai Lu <yinghai@kernel.org>
Date: Fri Dec 17 16:58:28 2010 -0800
x86-64, mm: Put early page table high
at some point init_memory_mapping is going to reach the pagetable pages
area and map those pages too (mapping them as normal memory that falls
in the range of addresses passed to init_memory_mapping as argument).
Some of those pages are already pagetable pages (they are in the range
pgt_buf_start-pgt_buf_end) therefore they are going to be mapped RO and
everything is fine.
Some of these pages are not pagetable pages yet (they fall in the range
pgt_buf_end-pgt_buf_top; for example the page at pgt_buf_end) so they
are going to be mapped RW. When these pages become pagetable pages and
are hooked into the pagetable, xen will find that the guest has already
a RW mapping of them somewhere and fail the operation.
The reason Xen requires pagetables to be RO is that the hypervisor needs
to verify that the pagetables are valid before using them. The validation
operations are called "pinning" (more details in arch/x86/xen/mmu.c).
In order to fix the issue we mark all the pages in the entire range
pgt_buf_start-pgt_buf_top as RO, however when the pagetable allocation
is completed only the range pgt_buf_start-pgt_buf_end is reserved by
init_memory_mapping. Hence the kernel is going to crash as soon as one
of the pages in the range pgt_buf_end-pgt_buf_top is reused (b/c those
ranges are RO).
For this reason we need a hook to reserve the kernel pagetable pages we
used and free the other ones so that they can be reused for other
purposes.
On native it just means calling memblock_x86_reserve_range, on Xen it
also means marking RW the pagetable pages that we allocated before but
that haven't been used before.
Another way to fix this is without using the hook is by adding a 'if
(xen_pv_domain)' in the 'init_memory_mapping' code and calling the Xen
counterpart, but that is just nasty.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Both warning and warning_symbol are nowhere used.
Let's get rid of them.
Signed-off-by: Richard Weinberger <richard@nod.at>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Soeren Sandmann Pedersen <ssp@redhat.com>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: x86 <x86@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Link: http://lkml.kernel.org/r/1305205872-10321-2-git-send-email-richard@nod.at
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Since segments need to be handled slightly differently when fetching
instructions, we add a __linearize helper that accepts a new 'fetch' boolean.
[avi: fix oops caused by wrong segmented_address initialization order]
Signed-off-by: Nelson Elhage <nelhage@ksplice.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The last_guest_tsc is used in vcpu_load to adjust the
tsc_offset since tsc-scaling is merged. So the
last_guest_tsc needs to be updated in vcpu_put instead of
the the last_host_tsc. This is fixed with this patch.
Reported-by: Jan Kiszka <jan.kiszka@web.de>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently we sync registers back and forth before/after exiting
to userspace for IO, but during IO device model shouldn't need to
read/write the registers, so we can as well skip those sync points. The
only exaception is broken vmware backdor interface. The new code sync
registers content during IO only if registers are read from/written to
by userspace in the middle of the IO operation and this almost never
happens in practise.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch implements two new vm-ioctls to get and set the
virtual_tsc_khz if the machine supports tsc-scaling. Setting
the tsc-frequency is only possible before userspace creates
any vcpu.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
With TSC scaling in SVM the tsc-offset needs to be
calculated differently. This patch propagates this
calculation into the architecture specific modules so that
this complexity can be handled there.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch implements a call-back into the architecture code
to allow the propagation of changes to the virtual tsc_khz
of the vcpu.
On SVM it updates the tsc_ratio variable, on VMX it does
nothing.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch changes the kvm_guest_time_update function to use
TSC frequency the guest actually has for updating its clock.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch enhances the kvm_amd module with functions to
support the TSC_RATE_MSR which can be used to set a given
tsc frequency for the guest vcpu.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The mmu_seq verification can be removed since we get the pfn in the
protection of mmu_lock.
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch adds code to check for IOIO intercepts on
instructions decoded by the KVM instruction emulator.
[avi: fix build error due to missing #define D2bvIP]
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch adds intercepts checks for the remaining twobyte
instructions to the KVM instruction emulator.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch adds the intercept checks for instruction
accessing the debug registers.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch adds all necessary intercept checks for
instructions that access the crX registers.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch adds a callback into kvm_x86_ops so that svm and
vmx code can do intercept checks on emulated instructions.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch adds a flag for the opcoded to tag instruction
which are only recognized in protected mode. The necessary
check is added too.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch adds a check_perm callback for each opcode into
the instruction emulator. This will be used to do all
necessary permission checks on instructions before checking
whether they are intercepted or not.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch prevents the changed CPU state to be written back
when the emulator detected that the instruction was
intercepted by the guest.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Add intercept codes for instructions defined by SVM as
interceptable.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
When running in guest mode, certain instructions can be intercepted by
hardware. This also holds for nested guests running on emulated
virtualization hardware, in particular instructions emulated by kvm
itself.
This patch adds a framework for intercepting instructions. If an
instruction is marked for interception, and if we're running in guest
mode, a callback is called to check whether an intercept is needed or
not. The callback is called at three points in time: immediately after
beginning execution, after checking privilge exceptions, and after
checking memory exception. This suits the different interception points
defined for different instructions and for the various virtualization
instruction sets.
In addition, a new X86EMUL_INTERCEPT is defined, which any callback or
memory access may define, allowing the more complicated intercepts to be
implemented in existing callbacks.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently we store a rep prefix as 1 or 2 depending on whether it is a REPE or
REPNE. Since sse instructions depend on the prefix value, store it as the
original opcode to simplify things further on.
Signed-off-by: Avi Kivity <avi@redhat.com>
Since sse instructions can issue 16-byte mmios, we need to support them. We
can't increase the kvm_run mmio buffer size to 16 bytes without breaking
compatibility, so instead we break the large mmios into two smaller 8-byte
ones. Since the bus is 64-bit we aren't breaking any atomicity guarantees.
Signed-off-by: Avi Kivity <avi@redhat.com>
We may read the cpl quite often in the same vmexit (instruction privilege
check, memory access checks for instruction and operands), so we gain
a bit if we cache the value.
Signed-off-by: Avi Kivity <avi@redhat.com>
This workaround holds a dma32 buffer at early boot to prevent later
bootmem allocations from stealing it in the case of large RAM configs.
Now that x86 is using memblock, and the nobootmem wrapper does top-down
allocation, it's no longer necessary, so remove it.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Move the interupt handling for the iommu into the interupt
thread to reduce latencies and prepare interupt handling for
pri handling.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This fixes problems seen on UV systems handling NMIs from the
node controller.
I isolated the "dazed..." messages that I saw earlier to a bug in
the BMC on our platform. It was sending NMIs w/o properly setting
a register that indicated the source of NMI.
So rather than _assuming_ any unhandled NMI came from the UV system
maintenance console (SMC), add a check to verify that the SMC actually
sent the NMI.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: gorcunov@gmail.com
Cc: dzickus@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The core EFI code and 64-bit EFI code currently have independent
implementations of code for setting memory regions as executable or not.
Let's consolidate them.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Link: http://lkml.kernel.org/r/1304623186-18261-2-git-send-email-mjg@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This patch adds a multiple message send syscall and is the send
version of the existing recvmmsg syscall. This is heavily
based on the patch by Arnaldo that added recvmmsg.
I wrote a microbenchmark to test the performance gains of using
this new syscall:
http://ozlabs.org/~anton/junkcode/sendmmsg_test.c
The test was run on a ppc64 box with a 10 Gbit network card. The
benchmark can send both UDP and RAW ethernet packets.
64B UDP
batch pkts/sec
1 804570
2 872800 (+ 8 %)
4 916556 (+14 %)
8 939712 (+17 %)
16 952688 (+18 %)
32 956448 (+19 %)
64 964800 (+20 %)
64B raw socket
batch pkts/sec
1 1201449
2 1350028 (+12 %)
4 1461416 (+22 %)
8 1513080 (+26 %)
16 1541216 (+28 %)
32 1553440 (+29 %)
64 1557888 (+30 %)
We see a 20% improvement in throughput on UDP send and 30%
on raw socket send.
[ Add sparc syscall entries. -DaveM ]
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that NUMA init path is unified, NUMA emulation can be enabled on
32bit. Make numa_emluation.c safe on 32bit by doing the followings.
* Define MAX_DMA32_PFN on 32bit too.
* Include bootmem.h for max_pfn declaration.
* Use u64 explicitly and always use PFN_PHYS() when converting page
number to address.
* Avoid __udivdi3() generation on 32bit by doing number of pages
calculation instead in split_nodes_interleave().
And drop X86_64 dependency from Kconfig.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
numa_init_array() no longer has users outside of numa.c. Make it
static.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
With both _numa_init() methods converted and the rest of init code
adjusted, numa_32.c now can switch from the 32bit only init code to
the common one in numa.c.
* Shim get_memcfg_*()'s are dropped and initmem_init() calls
x86_numa_init(), which is updated to handle NUMAQ.
* All boilerplate operations including node range limiting, pgdat
alloc/init are handled by numa_init(). 32bit only implementation is
removed.
* 32bit numa_add_memblk(), numa_set_distance() and
memory_add_physaddr_to_nid() removed and common versions in
numa_32.c enabled for 32bit.
This change causes the following behavior changes.
* NODE_DATA()->node_start_pfn/node_spanned_pages properly initialized
for 32bit too.
* Much more sanity checks and configuration cleanups.
* Proper handling of node distances.
* The same NUMA init messages as 64bit.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Generic NUMA init code was moved to numa.c from numa_64.c but is still
guaraded by CONFIG_X86_64. This patch removes the compile guard and
enables compiling on 32bit.
* numa_add_memblk() and numa_set_distance() clash with the shim
implementation in numa_32.c and are left out.
* memory_add_physaddr_to_nid() clashes with 32bit implementation and
is left out.
* MAX_DMA_PFN definition in dma.h moved out of !CONFIG_X86_32.
* node_data definition in numa_32.c removed in favor of the one in
numa.c.
There are places where ulong is assumed to be 64bit. The next patch
will fix them up. Note that although the code is compiled it isn't
used yet and this patch doesn't cause any functional change.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Move the generic 64bit NUMA init machinery from numa_64.c to numa.c.
* node_data[], numa_mem_info and numa_distance
* numa_add_memblk[_to](), numa_remove_memblk[_from]()
* numa_set_distance() and friends
* numa_init() and all the numa_meminfo handling helpers called from it
* dummy_numa_init()
* memory_add_physaddr_to_nid()
A new function x86_numa_init() is added and the content of
numa_64.c::initmem_init() is moved into it. initmem_init() now simply
calls x86_numa_init().
Constants and numa_off declaration are moved from numa_{32|64}.h to
numa.h.
This is code reorganization and doesn't involve any functional change.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Update numaq such that it calls numa_add_memblk() and sets
numa_nodes_parsed instead of directly diddling with NUMA states. The
original get_memcfg_numaq() is renamed to numaq_numa_init() and new
get_memcfg_numaq() is created in numa_32.c.
The shim numa_add_memblk() implementation handles node_start/end_pfn[]
and node_set_online() for nodes with memory. The new
get_memcfg_numaq() exactly the same with get_memcfg_from_srat() other
than calling the numaq init function. Things get_memcfgs_numaq() do
are not strictly necessary for numaq but added for consistency and to
help unifying NUMA init handling.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
SRAT support implementation in srat_32.c and srat.c are generally
similar; however, there are some differences.
First of all, 64bit implementation supports more types of SRAT
entries. 64bit supports x2apic, affinity, memory and SLIT. 32bit
only supports processor and memory.
Most other differences stem from different initialization protocols
employed by 64bit and 32bit NUMA init paths.
On 64bit,
* Mappings among PXM, node and apicid are directly done in each SRAT
entry callback.
* Memory affinity information is passed to numa_add_memblk() which
takes care of all interfacing with NUMA init.
* Doesn't directly initialize NUMA configurations. All the
information is recorded in numa_nodes_parsed and memblks.
On 32bit,
* Checks numa_off.
* Things go through one more level of indirection via private tables
but eventually end up initializing the same mappings.
* node_start/end_pfn[] are initialized and
memblock_x86_register_active_regions() is called for each memory
chunk.
* node_set_online() is called for each online node.
* sort_node_map() is called.
There are also other minor differences in sanity checking and messages
but taking 64bit version should be good enough.
This patch drops the 32bit specific implementation and makes the 64bit
implementation common for both 32 and 64bit.
The init protocol differences are dealt with in two places - the
numa_add_memblk() shim added in the previous patch and new temporary
numa_32.c:get_memcfg_from_srat() which wraps invocation of
x86_acpi_numa_init().
The shim numa_add_memblk() handles the folowings.
* node_start/end_pfn[] initialization.
* node_set_online() for memory nodes.
* Invocation of memblock_x86_register_active_regions().
The shim get_memcfg_from_srat() handles the followings.
* numa_off check.
* node_set_online() for CPU nodes.
* sort_node_map() invocation.
* Clearing of numa_nodes_parsed and active_ranges on failure.
The shims are temporary and will be removed as the generic NUMA init
path in 32bit is replaced with 64bit one.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
To help transition to common NUMA init, implement temporary 32bit
shims for numa_add_memblk() and numa_set_distance().
numa_add_memblk() registers the memblk and adjusts
node_start/end_pfn[]. numa_set_distance() is noop.
These shims will allow using 64bit NUMA init functions on 32bit and
gradual transition to common NUMA init path.
For detailed description, please read description of commits which
make use of the shim functions.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Move numa_nodes_parsed from numa_64.[hc] to numa.[hc] to prepare for
NUMA init path unification.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
There's no reason get_memcfg_numa() to be implemented inline in
mmzone_32.h. Move it to numa_32.c and also make
get_memcfg_numa_flag() static.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
* Kill no longer used struct bootnode.
* Kill dangling declaration of pxm_to_nid() in numa_32.h.
* Make setup_node_bootmem() static.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
NUMAQ is the only meaningful user of this callback and
setup_local_APIC() the only callsite. Stop torturing everyone else by
making the callback optional and removing all the boilerplate
implementations and assignments.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Currently, the only meaningful user of apic->x86_32_numa_cpu_node() is
NUMAQ which returns valid mapping only after CPU is initialized during
SMP bringup; thus, the previous patch to set apicid -> node in
setup_local_APIC() makes __apicid_to_node[] always contain the correct
mapping whether custom apic->x86_32_numa_cpu_node() is used or not.
So, there is no reason to keep separate 32bit implementation. We can
always consult __apicid_to_node[]. Move 64bit implementation from
numa_64.c to numa.c and remove 32bit implementation from numa_32.c.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Merge reason: Pick up the following two fix commits.
2be19102b7: x86, NUMA: Fix empty memblk detection in numa_cleanup_meminfo()
765af22da8: x86-32, NUMA: Fix ACPI NUMA init broken by recent x86-64 change
Scheduled NUMA init 32/64bit unification changes depend on these.
Signed-off-by: Tejun Heo <tj@kernel.org>
Make the comments a bit clearer for get_bios_ebda so that it actually
tells us what it is returning.
Signed-off-by: Mike Waychison <mikew@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a wrapper routine that tells us the length of the EBDA if it is
present. This guy also ensures that the returned length doesn't let the
EBDA run past the 640KiB mark.
Signed-off-by: Mike Waychison <mikew@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We use io_apic_setup_irq_pin() in order to configure pin's interrupt
number polarity and type. This is done on every irq_create_of_mapping()
which happens for instance during pci enable calls. Level typed
interrupts are masked by default, edge are unmasked.
On the first ->xlate() call the level interrupt is configured and
masked. The driver calls request_irq() and the line is unmasked. Lets
assume the interrupt line is shared with another device and we call
pci_enable_device() for this device. The ->xlate() configures the pin
again and it is masked. request_irq() does not unmask the line because
it _is_ already unmasked according to its internal state. So the
interrupt will never be unmasked again.
This patch is based on an earlier work by Torben Hohn and solves the
problem by configuring the pin only once. Since all devices must agree
on the same type and polarity there is no point in configuring the pin
more than once.
[ tglx: Split out the ce4100 part into a separate patch ]
Cc: Torben Hohn <torbenh@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/%3C20110427143052.GA15211%40linutronix.de%3E
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Conflicts:
include/linux/perf_event.h
Merge reason: pick up the latest jump-label enhancements, they are cooked ready.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Recently, we had a build failure on !CONFIG_PARAVIRT due to a
callback ->wbinvd() clashing with a macro wbinvd().
While we worked around the issue, avoid it in the future by
changing the macro (and a few surrounding ones) to an inline
function.
Signed-off-by: Avi Kivity <avi@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Link: http://lkml.kernel.org/r/1303632711-21662-1-git-send-email-avi@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The default notifier doesn't make a lot of sense to call in the
correctable errors case. Drop it and emit the mcelog decoding
hint only in the uncorrectable errors case and when no notifier
is registered. Also, limit issuing the "mcelog --ascii" message
in the rare case when we dump unreported CEs before panicking.
While at it, remove unused old x86_mce_decode_callback from the
header.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Nagananda Chumbalkar <Nagananda.Chumbalkar@hp.com>
Cc: Russ Anderson <rja@sgi.com>
Link: http://lkml.kernel.org/r/20110420102349.GB1361@aftab
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The cpu<->node mappings under CONFIG_DEBUG_PER_CPU_MAPS=y
when NUMA emulation is enabled is currently broken because it does
not iterate through every emulated node and bind cpus that have
affinity to it.
NUMA emulation should bind each cpu to every local node to
accurately represent the true NUMA topology of the underlying
machine.
debug_cpumask_set_cpu() needs to be fixed at the same time so
that the debugging information that it emits shows the new
cpumask of the node being assigned when the cpu is being added
or removed.
It can now take responsibility of setting or clearing the cpu
itself to remove the need for duplicate code.
Also change its last parameter, "enable", to have the correct bool
type since it can only be true or false.
-v2: Fix the return statements, by Kosaki Motohiro
Acked-and-Tested-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Andreas Herrmann <herrmann.der.user@googlemail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.00.1104201918470.12634@chino.kir.corp.google.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Clean up and unify the NOP selection infrastructure:
- Make the atomic 5-byte NOP a part of the selection system.
- Pick NOPs once during early boot and then be done with it.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jason Baron <jbaron@redhat.com>
Link: http://lkml.kernel.org/r/1303166160-10315-3-git-send-email-hpa@linux.intel.com
The DISTLBWALKPRB bit must be set for the GART because the
gatt table is mapped UC. But the current code does not set
the bit at boot when the BIOS setup the aperture correctly.
Fix that by setting this bit when enabling the GART instead
of the other places.
Cc: <stable@kernel.org>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Link: http://lkml.kernel.org/r/1303134346-5805-4-git-send-email-joerg.roedel@amd.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
We only supported the M2P (and P2M) override only for the
GNTMAP_contains_pte type mappings. Meaning that we grants
operations would "contain the machine address of the PTE to update"
If the flag is unset, then the grant operation is
"contains a host virtual address". The latter case means that
the Hypervisor takes care of updating our page table
(specifically the PTE entry) with the guest's MFN. As such we should
not try to do anything with the PTE. Previous to this patch
we would try to clear the PTE which resulted in Xen hypervisor
being upset with us:
(XEN) mm.c:1066:d0 Attempt to implicitly unmap a granted PTE c0100000ccc59067
(XEN) domain_crash called from mm.c:1067
(XEN) Domain 0 (vcpu#0) crashed on cpu#3:
(XEN) ----[ Xen-4.0-110228 x86_64 debug=y Not tainted ]----
and crashing us.
This patch allows us to inhibit the PTE clearing in the PV guest
if the GNTMAP_contains_pte is not set.
On the m2p_remove_override path we provide the same parameter.
Sadly in the grant-table driver we do not have a mechanism to
tell m2p_remove_override whether to clear the PTE or not. Since
the grant-table driver is used by user-space, we can safely assume
that it operates only on PTE's. Hence the implementation for
it to work on !GNTMAP_contains_pte returns -EOPNOTSUPP. In the future
we can implement the support for this. It will require some extra
accounting structure to keep track of the page[i], and the flag.
[v1: Added documentation details, made it return -EOPNOTSUPP instead
of trying to do a half-way implementation]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This patch disables GartTlbWlk errors on AMD Fam10h CPUs if
the BIOS forgets to do is (or is just too old). Letting
these errors enabled can cause a sync-flood on the CPU
causing a reboot.
The AMD BKDG recommends disabling GART TLB Wlk Error completely.
This patch is the fix for
https://bugzilla.kernel.org/show_bug.cgi?id=33012
on my machine.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Link: http://lkml.kernel.org/r/20110415131152.GJ18463@8bytes.org
Tested-by: Alexandre Demers <alexandre.f.demers@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
When the Xen PCI backend is told to enable or disable MSI/MSI-X functions,
the initial domain performs these operations. The initial domain needs
to know which domain (guest) is going to use the PCI device so when it
makes the appropiate hypercall to retrieve the MSI/MSI-X vector it will
also assign the PCI device to the appropiate domain (guest).
This boils down to us needing a mechanism to find, set and unset the domain
id that will be using the device.
[v2: EXPORT_SYMBOL -> EXPORT_SYMBOL_GPL.]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This patch adds detection of the extended features of an
AMD IOMMU. The available features are printed to dmesg on
boot.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch adds the necessary code to the AMD IOMMU driver
for enabling and disabling the ATS capability on a device
and to setup the IOMMU data structures correctly.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch adds a flag to the AMD IOMMU driver to indicate
that all IOMMUs present in the system support device IOTLBs.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch implements a function to flush the IOTLB on
devices supporting ATS and makes sure that this TLB is also
flushed if necessary.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Currently the option resides under X86_EXTENDED_PLATFORM due to historical
nonstandard A20M# handling. However that is no longer the case and so Elan can
be treated as part of the standard processor choice Kconfig option.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Link: http://lkml.kernel.org/r/1302245177.31620.47.camel@localhost.localdomain
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The old code only flushed a DTE or a domain TLB before it is
actually used by the IOMMU driver. While this is efficient
and works when done right it is more likely to introduce new
bugs when changing code (which happened in the past).
This patch adds code to flush all DTEs and all domain TLBs
in each IOMMU right after it is enabled (at boot and after
resume). This reduces the complexity of the driver and makes
it less likely to introduce stale-TLB bugs in the future.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The logic to reset the command buffer caused more problems
than it actually helped. The logic jumped in when the IOMMU
hardware doesn't execute commands anymore but the reasons
for this are usually not fixed by just resetting the command
buffer. So the code can be removed to reduce complexity.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Only pgdat and memmap use remap area and there isn't much benefit in
allowing per-node override. In addition, the use of node_remap_size[]
is confusing in that it contains number of bytes before remap
initialization and then number of pages afterwards.
Move remap size calculation for memap from specific NUMA config
implementations to init_alloc_remap() and make node_remap_size[]
static.
The only behavior difference is that, before this patch, numaq_32
didn't consider max_pfn when calculating the memmap size but it's
enforced after this patch, which is the right thing to do.
Signed-off-by: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/1301955840-7246-8-git-send-email-tj@kernel.org
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The linker should not be adding holes to word size aligned pointers, but
out of paranoia we are explicitly specifying that alignment. I have not
seen any holes in the jump label section in practice.
Signed-off-by: Jason Baron <jbaron@redhat.com>
LKML-Reference: <e119fbd060c9452c56063ea6148ba1070e7434cc.1300299760.git.jbaron@redhat.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Introduce:
static __always_inline bool static_branch(struct jump_label_key *key);
instead of the old JUMP_LABEL(key, label) macro.
In this way, jump labels become really easy to use:
Define:
struct jump_label_key jump_key;
Can be used as:
if (static_branch(&jump_key))
do unlikely code
enable/disale via:
jump_label_inc(&jump_key);
jump_label_dec(&jump_key);
that's it!
For the jump labels disabled case, the static_branch() becomes an
atomic_read(), and jump_label_inc()/dec() are simply atomic_inc(),
atomic_dec() operations. We show testing results for this change below.
Thanks to H. Peter Anvin for suggesting the 'static_branch()' construct.
Since we now require a 'struct jump_label_key *key', we can store a pointer into
the jump table addresses. In this way, we can enable/disable jump labels, in
basically constant time. This change allows us to completely remove the previous
hashtable scheme. Thanks to Peter Zijlstra for this re-write.
Testing:
I ran a series of 'tbench 20' runs 5 times (with reboots) for 3
configurations, where tracepoints were disabled.
jump label configured in
avg: 815.6
jump label *not* configured in (using atomic reads)
avg: 800.1
jump label *not* configured in (regular reads)
avg: 803.4
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20110316212947.GA8792@redhat.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Suggested-by: H. Peter Anvin <hpa@linux.intel.com>
Tested-by: David Daney <ddaney@caviumnetworks.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
phys_to_nid() maps physical address to NUMA node id. This is
implemented by building perfect hash in compute_hash_shift() during
initialization.
However, with SPARSE memory model, the nid is encoded in page flags.
The perfect hash implementation was for DISCONTIG memory model which
got removed years ago by b263295dbf (x86: 64-bit, make sparsemem
vmemmap the only memory model).
So, the perfect hash ends up being used only during initialization
when the core SPARSE code already provides perfectly acceptable
generic early_pfn_to_nid() implementation.
Drop phys_to_nid() and use the generic ealry_pfn_to_nid() instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Add this_cpu_has() which determines if the current cpu has a certain
ability using a segment prefix and a bit test operation.
For that we need to add bit operations to x86s percpu.h.
Many uses of cpu_has use a pointer passed to a function to determine
the current flags. That is no longer necessary after this patch.
However, this patch only converts the straightforward cases where
cpu_has is used with this_cpu_ptr. The rest is work for later.
-tj: Rolled up patch to add x86_ prefix and use percpu_read() instead
of percpu_read_stable().
Signed-off-by: Christoph Lameter <cl@linux.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Stop including <linux/delay.h> in x86 header files which don't
need it. This will let the compiler complain when this header is
not included by source files when it should, so that
contributors can fix the problem before building on other
architectures starts to fail.
Credits go to Geert for the idea.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: James E.J. Bottomley <James.Bottomley@suse.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
LKML-Reference: <20110325152014.297890ec@endymion.delvare>
[ this also fixes an upstream build bug in drivers/media/rc/ite-cir.c ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Omit the segment prefix in the UP case. GS is not used then
and we will generate segfaults if cmpxchg16b is used otherwise.
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (42 commits)
ACPI: minor printk format change in acpi_pad
ACPI: make acpi_pad /sys output more readable
ACPICA: Update version to 20110316
ACPICA: Header support for SLIC table
ACPI: Make sure the FADT is at least rev 2 before using the reset register
ACPI: Bug compatibility for Windows on the ACPI reboot vector
ACPICA: Fix access width for reset vector
ACPI battery: fribble sysfs files from a resume notifier
ACPI button: remove unused procfs I/F
ACPI, APEI, Add PCIe AER error information printing support
PCIe, AER, use pre-generated prefix in error information printing
ACPI, APEI, Add ERST record ID cache
ACPI: Use syscore_ops instead of sysdev class and sysdev
ACPI: Remove the unused EC sysdev class
ACPI: use __cpuinit for the acpi_processor_set_pdc() call tree
ACPI: use __init where possible in processor driver
Thermal_Framework-Fix_crash_during_hwmon_unregister
ACPICA: Update version to 20110211.
ACPICA: Add mechanism to defer _REG methods for some installed handlers
ACPICA: Add support for FunctionalFixedHW in acpi_ut_get_region_name
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
deal with races in /proc/*/{syscall,stack,personality}
proc: enable writing to /proc/pid/mem
proc: make check_mem_permission() return an mm_struct on success
proc: hold cred_guard_mutex in check_mem_permission()
proc: disable mem_write after exec
mm: implement access_remote_vm
mm: factor out main logic of access_process_vm
mm: use mm_struct to resolve gate vma's in __get_user_pages
mm: arch: rename in_gate_area_no_task to in_gate_area_no_mm
mm: arch: make in_gate_area take an mm_struct instead of a task_struct
mm: arch: make get_gate_vma take an mm_struct instead of a task_struct
x86: mark associated mm when running a task in 32 bit compatibility mode
x86: add context tag to mark mm when running a task in 32-bit compatibility mode
auxv: require the target to be tracable (or yourself)
close race in /proc/*/environ
report errors in /proc/*/*map* sanely
pagemap: close races with suid execve
make sessionid permissions in /proc/*/task/* match those in /proc/*
fix leaks in path_lookupat()
Fix up trivial conflicts in fs/proc/base.c
There is no user now.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: David Miller <davem@davemloft.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
minix bit operations are only used by minix filesystem and useless by
other modules. Because byte order of inode and block bitmaps is different
on each architecture like below:
m68k:
big-endian 16bit indexed bitmaps
h8300, microblaze, s390, sparc, m68knommu:
big-endian 32 or 64bit indexed bitmaps
m32r, mips, sh, xtensa:
big-endian 32 or 64bit indexed bitmaps for big-endian mode
little-endian bitmaps for little-endian mode
Others:
little-endian bitmaps
In order to move minix bit operations from asm/bitops.h to architecture
independent code in minix filesystem, this provides two config options.
CONFIG_MINIX_FS_BIG_ENDIAN_16BIT_INDEXED is only selected by m68k.
CONFIG_MINIX_FS_NATIVE_ENDIAN is selected by the architectures which use
native byte order bitmaps (h8300, microblaze, s390, sparc, m68knommu,
m32r, mips, sh, xtensa). The architectures which always use little-endian
bitmaps do not select these options.
Finally, we can remove minix bit operations from asm/bitops.h for all
architectures.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Michal Simek <monstr@monstr.eu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As the result of conversions, there are no users of ext2 non-atomic bit
operations except for ext2 filesystem itself. Now we can put them into
architecture independent code in ext2 filesystem, and remove from
asm/bitops.h for all architectures.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce little-endian bit operations to the big-endian architectures
which do not have native little-endian bit operations and the
little-endian architectures. (alpha, avr32, blackfin, cris, frv, h8300,
ia64, m32r, mips, mn10300, parisc, sh, sparc, tile, x86, xtensa)
These architectures can just include generic implementation
(asm-generic/bitops/le.h).
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Zankel <chris@zankel.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This tag is intended to mirror the thread info TIF_IA32 flag. Will be used to
identify mm's which support 32 bit tasks running in compatibility mode without
requiring a reference to the task itself.
Signed-off-by: Stephen Wilson <wilsons@start.ca>
Reviewed-by: Michel Lespinasse <walken@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Not all 64-bit systems require ISA-style DMA, so allow it to be
configurable. x86 utilizes the generic ISA DMA allocator from
kernel/dma.c, so require it only when CONFIG_ISA_DMA_API is enabled.
Disabling CONFIG_ISA_DMA_API is dependent on x86_64 since those machines
do not have ISA slots and benefit the most from disabling the option (and
on CONFIG_EXPERT as required by H. Peter Anvin).
When disabled, this also avoids declaring claim_dma_lock(),
release_dma_lock(), request_dma(), and free_dma() since those interfaces
will no longer be provided.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All architectures can use the common dma_addr_t typedef now. We can
remove the arch specific dma_addr_t.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a node parameter to alloc_thread_info(), and change its name to
alloc_thread_info_node()
This change is needed to allow NUMA aware kthread_create_on_cpu()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tejun Heo <tj@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is frequently useful to sync a single file system, instead of all
mounted file systems via sync(2):
- On machines with many mounts, it is not at all uncommon for some of
them to hang (e.g. unresponsive NFS server). sync(2) will get stuck on
those and may never get to the one you do care about (e.g., /).
- Some applications write lots of data to the file system and then
want to make sure it is flushed to disk. Calling fsync(2) on each
file introduces unnecessary ordering constraints that result in a large
amount of sub-optimal writeback/flush/commit behavior by the file
system.
There are currently two ways (that I know of) to sync a single super_block:
- BLKFLSBUF ioctl on the block device: That also invalidates the bdev
mapping, which isn't usually desirable, and doesn't work for non-block
file systems.
- 'mount -o remount,rw' will call sync_filesystem as an artifact of the
current implemention. Relying on this little-known side effect for
something like data safety sounds foolish.
Both of these approaches require root privileges, which some applications
do not have (nor should they need?) given that sync(2) is an unprivileged
operation.
This patch introduces a new system call syncfs(2) that takes an fd and
syncs only the file system it references. Maybe someday we can
$ sync /some/path
and not get
sync: ignoring all arguments
The syscall is motivated by comments by Al and Christoph at the last LSF.
syncfs(2) seems like an appropriate name given statfs(2).
A similar ioctl was also proposed a while back, see
http://marc.info/?l=linux-fsdevel&m=127970513829285&w=2
Signed-off-by: Sage Weil <sage@newdream.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Flush TLB if PGD entry is changed in i386 PAE mode
x86, dumpstack: Correct stack dump info when frame pointer is available
x86: Clean up csum-copy_64.S a bit
x86: Fix common misspellings
x86: Fix misspelling and align params
x86: Use PentiumPro-optimized partial_csum() on VIA C7
