Wireless device may implement a logic to kick-out STA due to inactivity
for a certain period of time. This feature needs to be advertised to
higher layers if supported. Timeout value is still taken from
parameters to START_AP command, nothing changes here.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Current recovery approach is to wake s/w Tx queues for skb->dev netdevice.
However this approach doesn't cover the case when h/w queue is full of
packets from a single wireless interface. Suppose xmit attempt from the
second wireless interface fails due to failed reclaim. Then the second
interface will not have a chance to recover even if subsequent reclaims
succeed. Possible solution is to attempt to wake all the s/w queues
belonging to driver interfaces.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function qtnf_classify_skb_no_mbss has been used for debug
during early stage of development. Drop its declaration.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Support registration for more mgmt frame types
for debug and monitoring purposes.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Under heavy load it is normal that h/w Tx queue is almost full all the time
and reclaim should be done before transmitting next packet. Warning still
should be reported as well as s/w Tx queues should be stopped in the
case when reclaim failed.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Igor Mitsyanko <imitsyanko@quantenna.com>
Cc: Avinash Patil <avinashp@quantenna.com>
Cc: Sergey Matyukevich <smatyukevich@quantenna.com>
Cc: Kamlesh Rath <krath@quantenna.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Linux Wireless device structure already has current channel
information that can be used when needed. Start using it.
Since driver's channel info is not used anymore, remove it.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Encryption info is a constant part of STA settings, no point
to pass it as an optional TLV.
Remove QTN_TLV_ID_CRYPTO type as it's not used anymore.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This cached state is used only once immediately after it is
initilized, except for BSSID value that is used for events processing.
There is no reason in keeping unused data in driver's state.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
QTNF_STATE_AP_START usage is redundant and imposes additional state
synchronization maintenance. We may as well leave state checking
to network card and upper layers (cfg80211, nl80211 and userspace).
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
QTNF_STATE_AP_CONFIG is redundant and its usage can be safely removed.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introduce "channel definition" TLV containing full channel
description (center frequence for both segments + BW) and pass it to
wireless card in a payload to START_AP command.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Modify QLINK START_AP command payload to pass all AP settings
contained within struct cfg80211_ap_settings.
Make most of settings a constant part of "config AP" command
instead of passing it as an optional TLVs.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Cached AP setings are passed to WiFi card right after they are
initialized and are never used for anything else. There is no
point in keeping them in driver state.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wireless device may send "channel changed" event before driver
registered this device with wireless core, which will result in
warnings.
Once device is registered, higher layer will query channel info
manually using .get_channel callback.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are no users of this field and it can safely be removed.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It is never used for anything useful, and all logic is handled by
either WiFi card or higher layers.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not assume whether wireless device can or can not handle switching
several interfaces on a single radio to different channels. Device will
handle it itself and will return appropriate error code.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
No reason to verify channel switch request in driver, it can simply be
forwarded to wireless device. Device can perform required checks and
return appropriate error code, and driver may not even have information
on current operational channel.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This makes no sense because real operational channel is choosen based
on AP operation, not on what STA is configured to.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not try to cache current operational channel info in driver, this
is a potential source of synchronization issues + driver does not
really need that info.
Introduce GET_CHANNEL command and process it appropriately.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Specifically, it has to report center frequency, secondary center
frequency (for 80+80) and BW.
Introduce channel definition structure to qlink and modify channel
change event processing function accordingly.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This will allow to use qlink channel width values to specify BW setting
corresponding to enum nl80211_chan_width.
Current user is converted to apply BIT() macro manually to each individual
qlink_channel_width enumeration value.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Cancel active scans and deactivate firmware scan watchdog timer
when wireless interface configuration is changed. The usecases
include wireless interface mode change, interface down,
AP stop, virtual interface removal.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix tx path regression. Lock should be held when queuing packets
to h/w fifos in order to properly handle configurations with
multiple enabled interfaces.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use 64-bit dma for hosts with CONFIG_ARCH_DMA_ADDR_T_64BIT enabled.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Check if skb tracking arrays has been already allocated. This additional
check handles the case when init partially failed.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
NULL is not a special type of success here but a error pointer.
So it makes sense to check against NULL in qtnf_map_bar
and return error code.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Linux built-in circ_buf implementation assumes that that the
circular buffer length is a power of 2. Make sure that
rx and tx descriptor queue lengths are power-of-2.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Flag -D__CHECK_ENDIAN was wrong: it should be -D__CHECK_ENDIAN__ instead.
However now this flag is enabled by default, so it can be removed.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Perform additional reclaim from qtnf_pcie_data_tx. Lock tx_lock serves only
reclaim synchronization purposes. Rename it accordingly and improve
granularity moving this lock to qtnf_pcie_data_tx_reclaim.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introduce counter for Rx underflow events. Export this counter via debugfs.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Current code for both Rx and Tx queue management is a custom and incomplete
circular buffer implementation. It makes a lot of sense to switch to kernel
built-in circ_buf implementation.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avoid extra buffering in driver by default. Use max hardware Tx queue size.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Update PCIE_HDP_TX_HOST_Q_WR_PTR register in skb2rbd_attach as a part of
procedure of passing new Rx buffer to hardware. Sync up all the the
qtnf_rx_bd descriptor updates before passing Rx buffer to hardware.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Replace __dev_alloc_skb and explicit NET_IP_ALIGN alignment by built-in
__netdev_alloc_skb_ip_align function.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use napi_gro_receive() rather than netif_receive_skb() to improve
performance when GRO is enabled.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the only caller of dma_supported() outside of DMA API internals, the
qtfnmac driver stands out and invites scrutiny. Thankfully, it's not
being used for evil, but it is entirely redundant, since it open-codes a
check that the DMA mask setting functions are going to perform anyway.
In fact, the whole qtnf_pcie_init_dma_mask() function is nothing more
than a rather long-winded implementation of dma_set_mask_and_coherent(),
so let's just use that directly.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Modify qlink command structures and interface types handling
to prepare adding AP_VLAN support to qtnfmac driver.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function is not used anymore, so remove it.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware sends supported interface type rather than mask. As a result,
types field of ieee80211_iface_limit structure may end up having
multiple iftype bits set. This leads to WARN_ON from
wiphy_verify_combinations.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Userspace tools may hang on scan in the case when scan completion event
is not returned by firmware. This patch implements the scan timeout
to avoid such situation.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch implements cfg80211 channel_switch handler enabling CSA
channel-switch procedure.
Driver performs only basic validation of the requested new channel
and then sends command to firmware. Beacon IEs are not sent since
beacon update is handled by firmware.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wireless cfg80211 core supplies channel settings in cfg80211_ap_settings
structure for each BSS in multiple BSS configuration. On the other hand
all the virtual interfaces on one radio are using the same PHY settings
including channel.
Move chandef structure from vif to mac structure in order to mantain
the only instance of cfg80211_chan_def structure in qtnf_wmac
rather than its multiple copies in qtnf_vif.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use proper endianness conversion for client station leave reason.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement current channel reporting functionality. Current operating
channel can be obtained either directly using cfg80211 get_channel
callback or from stats reported by cfg80211 survey_dump callback.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
