Controllers that support DMA of protection information must be told
explicitly how to handle the I/O. The controller has no knowledge of
the protection capabilities of the target device so this information
must be passed in the scsi_cmnd.
- The protection operation tells the HBA whether to generate, strip or
verify protection information.
- The protection type tells the HBA which layout the target is
formatted with. This is necessary because the controller must be
able to correctly interpret the included protection information in
order to verify it.
- When a scsi_cmnd is reused for error handling the protection
operation must be cleared and saved while error handling is in
progress.
- prot_op and prot_type are placed in an existing hole in scsi_cmnd
and don't cause the structure to grow.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Controllers that support protection information must indicate this to
the SCSI midlayer so that the ULD can prepare scsi_cmnds accordingly.
This patch implements a host mask and various types of protection:
- DIF Type 1-3 (between HBA and disk)
- DIX Type 0-3 (between OS and HBA)
The patch also allows the HBA to set the guard type to something
different than the T10-mandated CRC.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Create a cache of devices that are seen in a system. This will avoid
the unnecessary traversal of the device list in the scsi_dh when there
are multiple luns of a same type.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
multipath keeps a separate device table which may be
more current than the built-in one.
So we should make sure to always call ->attach whenever
a multipath map with hardware handler is instantiated.
And we should call ->detach on removal, too.
[sekharan: update as per comments from agk]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch updates the RDAC device handler to
refuse to attach to devices not supporting the
RDAC vpd pages.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch updates the hp_sw device handler to properly
check the return codes etc.
And adds the 'correct' machine definitions.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch converts the EMC device handler to use a proper
state machine. We now also parse the extended INQUIRY
information to determine if long trespass commands are
supported. And we're now using the long trespass command
correctly. And finally there's now an check at init time
to refuse to attach to devices not supporting EMC-specific
VPD pages.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Implement a 'dh_state' sdev attribute for dynamic device handler
manipulation. A read on the attribute will return the name of
the currently attached device handler or 'detached' if no handler
is attached.
The attribute allows the following strings to be written:
- The name of the device handler to be attached if the state is
'detached'.
- 'activate' to trigger path activation if a device handler
is attached.
- 'detach' to detach the currently attached device handler.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Instead of having each and every driver implement its own
device table scanning code we should rather implement a common
routine and scan the device tables there.
This allows us also to implement a general notifier chain
callback for all device handler instead for one per handler.
[sekharan: Fix rejections caused by conflicting bug fix]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Daniel Debonzi reports that he has managed to wrap host_no. Increasing
the number of host numbers available to 32-bit from 16-bit allows the
problem to be evaded for another hundred years.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Update index allocation as follows.
* sd_index_idr is used only for ID allocation and mapping
functionality is not used. Use more memory efficient ida instead.
* idr and ida have their own locks inside them and don't need them for
operation. Drop it.
* index wasn't freed if probing failed after index allocation. fix
it.
* ida allocation should be repeated if it fails with -EAGAIN.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When drivers use a shared tag map we can end up with more requests
than tags, because the tag map is shost->can_queue tags and there
can be sdevs * sdev->queue_depth requests. In scsi_request_fn
if tag allocation fails we just drop down to just dequeueing the
tag without a tag. The problem is that drivers using the shared tag
map rely on a valid tag always being set, because it will use the
tag number to lookup commands later.
This patch has us check if we got a valid tag when the host lock
is held right before we check if the host queue is ready. We do the
check here because to allocate the tag we need the q lock, but
if the tag is bad we want to add the device/q onto the starved list
which requires the host lock.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We want to set the queue depth to something reasonable - not
the can_queue.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We want to set the queue depth to something reasonable - not
the can_queue.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Currently qla4xxx and stex pass in their can_queue values into
scsi_activate_tcq because they wanted the tag map that large.
The problem with this is that it ends up also setting the queue
depth to that large value. All we want to do this in this case
is set the device queue depth and the other device settings.
We do not need to touch the tag map sizing because the drivers
had setup that map according to their can_queue limits when the
shared map was created.
The scsi mid layer in request_fn will then handle the case where we
have more requests than available tags when it checks the host
queue ready function.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mike Christie noticed a bogus memset. It can be removed as dead code
since the number of bytes in the driver buffer in fixed block mode is
always a multiple of the tape block size.
Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Move buffer pointer back when data could not be written. Bug found by
Mike Christie.
Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Use the full buffer size available, as there's no reason to limit
the firwmare-image load-segment size for these parts.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add an additional check to verify that the current executing
firmware is in fact non-ROM code. The non-ROM Get-ID mailbox
command is used for verification.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Total ram words can exceed a 16bit value on large-memory boards.
Safely extend to a 32bit width.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Firmware does not have the facilities to issue management server
IOCBs.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There were several issues here, one, during RSCN handling if a
follow-on RSCN occurred (within interrupt context) the DPC thread
could inadvertantly leave the fcport in a stale lost state.
Secondly, scheduled rport removal is handled exclusively by the
'parent' DPC thread, so wake up the proper thread. Finally,
process vport loop-resync's only when the vport has in an
"active" state (ID acquired).
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
By allowing the qla2x00_alert_all_vps() to manage per-vport
recognition of the MBA.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
All fcport->state management should be done within
qla2x00_mark_device_lost(), the assignment of state within
qla2x00_mark_vp_devices_dead() caused associated rports to not be
removed.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
While issuing a marker, manipulating the request/response queues
and modifying the outstanding command array.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The firmware group has suggested that FCE (Fibre Channel Event)
tracing be enabled prior to EFT (Extended Firmware Tracing) to
maximize the capturing of data on the wire. This change has no
real semantic effect on driver operation, as it's mostly a
shuffling of code.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Recent ISPs have this information written at manufacturing time,
so use the information. This also reduces future churn of the
qla_devtbl.h file contents, as the driver can now depend on the
information to be present in VPD.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
iIDMA support requires the driver issue several additional
fabric-managegment (FM) commands per port discovered during SNS
scanning -- GFPN (Get Fabric Port Name) and GPSC (Get Port Speed
Capabilities). It has been found during testing that some
switches do not respond as *well* as expected to these commands
(silence -- no ACC nor BS_RJT). So, to handle such conditions,
allow the user the ability to indirectly disable the FM commands
by disabling iIDMA with the ql2xiidmaenable module-parameter.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Removed repeated or unnecessary operations during vport
creation/deletion.
Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This parameter counts the total number of ISP aborts during
driver execution. The value is exported through a DEVICE_ATTR()
off the scsi_host.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As there's no point in adding a fixed-fudge value (originally 5
seconds), honor the user settings only. We also remove the
driver's dead-callback get_rport_dev_loss_tmo function
(qla2x00_get_rport_loss_tmo()).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Commit 2c96d8d0c1 pushed the
acquisition of hardware_lock to too fine a level, which in turn
will cause problems with cond_resched()s added with
40a2e34a94.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The new code in commit 5cbf1565f2
has a bug in the version supporting the AMD 'syscall' instruction.
It clobbers the user's %ecx register value (with the %ebp value).
This change fixes it.
Signed-off-by: Roland McGrath <roland@redhat.com>
Compile error on other architectures:
CC drivers/mfd/tc6393xb.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/mfd/tc6393xb.c: In function ‘tc6393xb_attach_irq’:
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/mfd/tc6393xb.c:324: error: implicit declaration of function ‘set_irq_flags’
...
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduced by commit aaca0bdca5 ("flag
parameters: paccept"):
net/socket.c:1515:17: error: symbol 'sys_paccept' redeclared with different type (originally declared at include/linux/syscalls.h:413) - incompatible argument 4 (different address spaces)
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 9115d13453 ("powerpc: Enable
AT_BASE_PLATFORM aux vector") broke boot on 32-bit powerpc systems; we
have to use PTRRELOC to initialize powerpc_base_platform this early in
boot.
Bug reported by Jon Smirl.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This wires up the recently added Wire up signalfd4, eventfd2,
epoll_create1, dup3, pipe2, and inotify_init1 system calls.
Signed-off-by: David S. Miller <davem@davemloft.net>
These got unintentionally moved, put them back as x86 provides its own
versions.
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes the dummy asm/kvm.h files on architectures not (yet)
supporting KVM and uses the same conditional headers installation as
already used for a.out.h .
Also removed are superfluous install rules in the s390 and x86 Kbuild
files (they are already in Kbuild.asm).
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
fix:
arch/x86/ia32/built-in.o: In function `ia32_sys_call_table':
(.rodata+0xa38): undefined reference to `compat_sys_signalfd4'
on !CONFIG_SIGNALFD.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
