This will allow the low level driver to make decision based
on the vif such as queues etc...
Since the vif might be NULL, we can't add it to the tracing
functions.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[fix staging rtl8821ae driver]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It was possible to create/delete/start/stop
monitor vdev from a few places that were not
exclusively protected against each other. This
resulted in monitor vdev being stopped/removed by
one call origin while another one was expecting it
to continue running.
For example if CAC was started and interface's
promiscuous mode was toggled monitor vdev was
removed from the driver meaning no radar would be
detected. In additional a warning would be printed
upon CAC completion complaining it tried to stop
non-running monitor vdev.
The patch simplifies monitor code by removing
IEEE80211_HW_WANT_MONITOR_VIF (which wasn't really
ever needed) and improves state tracking. It also
unifies prints.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
They were just too superfluous and made it harder to read logs. Change them to
follow the normal style used in ath10k.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
As pointed out by Michal Kazior, add extra pdev stats
for 10.1 firmware.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
FW stats does provide the Rx rate information. Add this.
Tested with firmware 10x firmware.
Increase buffer size so more peers can be shown.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Tested on 10.x firmware, and others report it at least
makes older firmware no more broken than it already was.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The filed has been missing (missmatched with FW ABI)
since 999.999.0.629 firmware release.
It's very imporatant to keep these structs up to date with FW,
due to the arithmetic we use while read the fw_stats.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since copy engine allocation has been revised the
ath10k_pci_ce_deinit() now simply zeroes copy
engine registers. It's probably a good idea to do
that before reseting for a more graceful device
reset.
Before ath10k_pci_ce_deinit() freed copy engine
ringbuffer memory so it was required to call it
after resetting. Otherwise it was possible for
device to access unmapped/freed copy engine
ringbuffer memory.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Definitions by which copy engine structure are
allocated do not change so it doesn't make much
sense to re-create those structures each time
device is booted (e.g. due to firmware recovery).
This should decrease chance of memory allocation
failures.
While at it remove per_transfer_context pointer
indirection. The array has been trailing the copy
engine ringbuffer structure anyway. This also
saves pointer size worth of bytes for each copy
engine ringbuffer.
Reported-By: Avery Pennarun <apenwarr@gmail.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This allows to use GFP_KERNEL allocation. This
should decrease chance of allocation failure, e.g.
during firmware recovery.
Reported-By: Avery Pennarun <apenwarr@gmail.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To make it easier to debug pci problems improve the log messages in pci.c. Also
change some debug messages to warning messages to more easily catch problems.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We do not really support older firmware API 1 anymore, so better remove
MODULE_FIRMWARE() declarations for them and only list for API 2 files.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The parameter name was ath10k_target_ps, but actually it should be just
target_ps. Module parameter names should not use the ath10k_ prefix.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
As cold reset is not reliable with CUS223 boards, make it possible
to disable cold reset entirely and only use warm reset. This makes it also
easier to debug warm reset problems.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k_pci_wait_for_target_init() did really follow the style used elsewhere in
ath10k. Use ath10k_pci_read/write() wrappers, simplify the while loop and
improve warning messages.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If OTP or firmware fails to load properly, print out some
extra info in the kernel logs.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Let user know the name of the board file if it is not
found, and make it easier to determine the firmware
api being used.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently there are different styles used for warning messages, unify them to
look similar. The style basically is:
1) start with a verb (if possible)
2) lower case letters
3) use plain english as much as possible
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
RSSI and RATES fields are valid only when START_VALID
bit is set. So, in current implementation we have to
remember/caclulate them when START_VALID and report the same
when only END_VALID is set.
Currently during heavy traffic we could have:
- 10 packets with START_VALID - correct RSSI and RATES
- 10 packets with END_VALID
- 10 packets with START_VALID - correct RSSI and RATES
- 10 packets with END_VALID
...
Next using monitor interface we will see:
- 10 packets with correct rssi/rates
- 10 packets with rssi=-95/rate=6Mbps
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Introduce rx_status htt template instead of
stack version, as a preparation for fix
rssi and rates reporting.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Struct htt_rx_info is not needed anymore while
we will use ieee80211_rx_status structure as
a template.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove almost the same code, and do only once
__le32_to_cpu() conversion.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Return error when rx_amsdu_pop() will fail.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Kill rates, tsf, fcs_err, mic_err, amsdu_more, encrypt_type, signal
from htt_rx_info and setup this directly in ieee80211_rx_status.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Setup band and frequency in ieee80211_rx_status
only once - for ppdu.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Will be used as a template, and final storage for
rx_status.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Using the macro to convert the MAC address from WMI word
format to char array has lead to the wrong peer mac
address printed out while retrieving the peer stats from
FW. Fix this.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Reviewed-By: Michał Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Regulatory domain settings for firmware 10.x has more options
than main firmware, so handle regulatory domain setup separately
for both supported firmwares. Fill in additional dfs domain
parameter according to current regulatory.
This patch does not solve any known bug. Not handled parameter
for firmware 10.x was found during code review.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Command WMI_FORCE_FW_HANG_CMDID is not supported in firmware 10.1.
In order to have firmware crash simulation functionality also
in firmware 10.1 driver can force firmware crash by performing not allowed
operation. Driver can deliberately crash firmware when setting vdev param for
vdev id out of range. This patch introduces two keywords to simulate_fw_crash:
'soft' which will cause firmware crash that is recoverable
by warm firmware reset but supported only in main firmware.
'hard' which will cause firmware crash recoverable by cold
firmware reset, this option works for both firmwares.
Commands to trigger firmware soft/hard crash:
echo 'soft' > /sys/kernel/debug/ieee80211/phyX/ath10k/simulate_fw_crash
echo 'hard' > /sys/kernel/debug/ieee80211/phyX/ath10k/simulate_fw_crash
kvalo: remove '\n' before checking the command and simplify how buf is null
terminated
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Don't fill this for each msdu, while this is the
same.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Introduce ath10k_htt_rx_amsdu_allowed() function, that
group code for checking if skip amsdu packets.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When we execute otp.bin in the target check that the result it returns doesn't
contain an error. This is to make sure that we don't accidentally use invalid
calibration data.
While at it, remove the useless label in the function and add few debug messages.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's just cleaner to have separate argument for the parameter and result. Also
fix returned error value if response length is invalid.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add recalculation of RTS/CTS protection when one or more legacy
stations are connected to ath10k. In this case enable RTS/CTS
protection and set sw retry profile are needed in the FW.
Without this change legacy station is starved and has very low
throughput.
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
IBSS mode requires the changing of supported rate. Do this
by reassociate the peer. The investigation shows that if move
from legacy to HT, the rate control won't work after changing
the supported rate. But once changing the supported rate to HT,
user can assign the TxRate in HT mode.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Seems like we have an old bug, where we incidently overwrites
the max_antenna_gain we pass to firmware, with zero value.
End of all we are artifically reducing the output power.
This patch removes the excessive assignment on max_antenna_gain,
which is being provided by regulatory domain, and consequently
improves the tx power.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Consolidate the list of msdu skbs into the msdu-head skb, delete the
rest of the skbs, pass the msdu-head skb on up the stack as normal.
Tested with high-speed TCP and UDP traffic on modified firmware that
supports raw-rx.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When using multiple vdevs (stations, aps, etc), it is
nice to be able to associate log messages with specific
interfaces. So, add vdev-id to most logging messages.
Add return code as well, where it was missing.
kvalo: unify some of the messages to follow the same style
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It doesn't make much sense to calculate the ring
size fill count because it already is memoized in
a separate variable.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
One of the premises was to guarantee serialized
completion handling for upper layers
(HTC/WMI/HTT). Since quite some time now it is no
longer necessary.
The other premise was to batch up tx/rx
completions to take advantage of hot caches.
However frame tx/rx completion indications come in
on a single pipe already so they are already
batched up. More meaningful batching is done in
HTT itself.
This means PCI completion is no longer necessary
to keep around. It just wastes memory, cycles and
SLOC.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is inefficient to grab irqsave spinlocks for
skb lists for each queue/dequeue action.
Using rx_ring.lock and tx_lock allows to use less
heavy bh spinlock functions and moving locking
upwards allows to toggle spinlocks less often.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HTT Rx endpoint processes both frame rx
indications and frame tx completion indications.
Those completions typically come in batches and
may be mixed so it makes sense to defer processing
hoping to get a bunch of them and take advantage
of hot caches.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Going through full htc tx path for htt tx is a
waste of resources. By skipping it it's possible
to easily submit scatter-gather to the pci hif for
reduced host cpu load and improved performance.
The new approach uses dma pool to store the
following metadata for each tx request:
* msdu fragment list
* htc header
* htt tx command
The htt tx command contains a msdu prefetch.
Instead of copying it original mapped msdu address
is used to submit a second scatter-gather item to
hif to make a complete htt tx command.
The htt tx command itself hands over dma mapped
pointers to msdus and completion of the command
itself doesn't mean the frame has been sent and
can be unmapped/freed. This is why htc tx
completion is skipped for htt tx as all tx related
resources are freed upon htt tx completion
indication event (which also implicitly means htt
tx command itself was completed).
Since now each htt tx request effectively consists
of 2 copy engine items CE_HTT_H2T_MSG_SRC_NENTRIES
is updated to allow maximum of
TARGET_10X_NUM_MSDU_DESC msdus being queued. This
keeps the tx path resource management simple.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
PCI is capable of handling scatter-gather lists.
This can be used to avoid copying memory.
Change the name of the callback while at to
reflect its purpose.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The flag wasn't used anymore. No need to keep it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There's no real benefit from using them. DMA-API
already provides debugging. Some skbuffs are
already mapped directly with DMA-API since wrapper
arguments were insufficient and extending them
would be pointless.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
After we pass frames with INV_PEER to upper layer in commit 716ae53c56
("ath10k: pass frames with invalid peer status to upper layer") we could pass
some management frames (in case INVALID_PEER and MGMT_CTRL) twice to upper
layer, once via WMI and once via HTT. Next we could handle assoc request twice.
This patch remove such regression.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Indicate spectrum management support in hardware
flags, while we already handle power set
(IEEE80211_CONF_CHANGE_POWER) in the ath10k driver.
This enable 802.11h support for station mode.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Retrieve the mactime of ieee80211_rx_status based on received
data frame. The value is obtained from the htt_rx_indication_ppdu
structure and only available in 32-bit.
kvalo: white space fixes
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The arsta structure wasn't initialized for
non-ap interfaces. This should fix related
warnings/crashes.
Reported-By: Ben Greear <greearb@candelatech.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The nwifi header is padded to 4 bytes. This wasn't
a problem until one tried to (at least) rx 4addr
frames.
This finally allows managed iface to be used in a
bridge.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Makes it easier to determine why some failures
happened.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Implement the get TSF by simply returning 0 so that IBSS
merging is happening. Otherwise, IBSS nodes that have similar
SSID naming won't merge. This is simply fooling the mac80211
that the TSF in the received beacon is higher than the local TSF.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This allows dynamic changes of bandwidth/nss/smps,
e.g. via ht/vht operation mode change
notification.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware ignores SMPS flags in peer assoc command.
For SMPS to work it is necessary to set peer
parameter after peer assoc command so that tx
chainmask is setup properly.
This should fix packet loss and improve throughput
with stations that have SMPS enabled upon
association.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
I modified Michal's commit c930f744bd ("ath10k: implement channel switching") to return
when vdev_start() fails, but forgot to release conf_mutex.
Found by coccinelle:
>> drivers/net/wireless/ath/ath10k/mac.c:2745:5-11: preceding lock on line 2663
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes a checkpatch warning in ath10k:
drivers/net/wireless/ath/ath10k/mac.c:1636: WARNING: Avoid CamelCase: <regpair->regDmnEnum>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix a checkpatch warning:
drivers/net/wireless/ath/ath10k/debug.h:95: CHECK: Alignment should match open parenthesis
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
As result deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case IRQ configuration is unknown possibly enabled MSIs
are left enabled in ath10k_pci_deinit_irq(). This update
fixes the described misbehaviour.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The documentation states that pci_enable_msi_block() returns the number of
requests 'could have been allocated', not 'could allocate'. IOW, MSIs are *not*
enabled if a positive value returned.
kvalo: add commit log based on Alexander's email
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pass frames with invalid peer status to upper layer.
Next mac80211 will validate frames and drop if required.
This is required to detect spurious frames and pass
this info to user mode (detect CLASS2 CLASS3 frames from
nonauthenticated/nonassociated stations).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is a workaround for HT-enabled STAs which break the spec
and have no HT capabilities RX mask (no HT RX MCS map).
As per spec, in section 20.3.5 Modulation and coding scheme (MCS),
MCS 0 through 7 are mandatory in 20MHz with 800 ns GI at all STAs.
Firmware asserts if such situation occurs.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case of warm reset target need to be suspended.
Suspend function is extented to handle both cases
with disabling interrupts and without disabling interrupts.
Warm target reset requires suspend with all interrupts
disabled.
This patch depends on
ath10k: fix device initialization routine
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Suspend/resume callbacks are not protected by configuration mutex
so adding such protection. Also in order to simplify implemetation
of suspend function wait queue is replaced by completion.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Hardware CUS232 version 2 has some issues with cold
reset that lead to Data Bus Errors or system hangs
in some cases. It's safer to use warm reset when
possible as it shouldn't trigger the
aforementioned issues.
Prefer warm reset over cold reset. However since
warm reset doesn't work after FW crash make sure to
fallback to cold reset when booting up the HW.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was found during testing the nss calculation does not
cover all corner cases. Station could request eq. only MCS8
and MCS9 (nss=2 specific). Next num_rates=2 so the driver
sets nss=(max((2+7)/8, 1))=1. Which is wrong. The in-driver
calculation was introduced prior (commit ddcc347b70
mac80211: fix rx_nss calculation for drivers with hw rc).
Since it's fixed, use mac80211 provided value from now.
End user will experience lower throuhputs than expected
if the nss is wrongly calculated.
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This throw a lot of pointless warnings in case of DFS (radar
detection) and PHYERR events from firmware, when firmware may
actually insert more data, than we assume.
Besides of being noisy this debug does not protect or check
anything usefull currently. It was introduced long time ago
while debugging aggregations. So just removing it.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Show message length and expected length. Helps debug
firmware mismatch issues.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ieee80211_rx_status.flags is full. Define a new vht_flag
variable to be able to set more VHT related flags and make
room in flags.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com> [ath10k]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Aids in understanding excactly what a firmware is
offering.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ARP frames exchange does not work properly for UAPSD enabled AP.
ARP requests which arrives with access category 0 are processed
by network stack and send back with access category 0. FW changes
access category to 6. This is causing problems when UAPSD associated
STA is sleeping after has sent ARP request. Configure ARP access
category in FW to best effort (0) solves this problem. ARP frames
will be send with access category 0.
Simplify arp ac override functionality by removing redundant entry in
pdev param maping table. There should be only one entry in pdev param
map but enum has different name for different FW.
kvalo: change the warning message
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Until now ath10k used a copy-by-value beacon
submission.
The new method passes a DMA address via WMI
command only. This command contains additional
metadata that fixes AP behaviour with regard
to powersave buffering.
This also fixes strange bug when multicast traffic
would freeze TX indefinitely.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Most channel switching logic has been implemented
already so this patch is pretty small. The patch
makes use of mac80211's vif->csa_active for AP CSA
handling.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Until now channel change wasn't propagating to FW
directly because operational channel is abstracted
by VDEVs and it wasn't really necessary since
ath10k implements hwscan and hwroc.
This effectively fixes STA CSA and allows for
future AP-like CSA as well.
kvalo: change error handling in ath10k_bss_info_changed()
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.x FW has no structure member sw_version_1. Thus,
both fw_version_release and fw_version_build are not
available. The provided fw_version_major is also wrong.
Fix this by using the fw_version from struct wiphy.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k handles UAPSD completly in the firmware.
When works in AP mode we have to configure
UAPSD params for each station. Without this
patch we configure UAPSD params before we
send peer assoc command to the FW, which was
wrong. Next FW didn't know what should be trigger
frame, couse UAPSD didn't work correctly in AP mode.
To configure UAPSD params correctly we have to
send them after peer assoc command.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware has a feature to track if the associated STA is not acking the frames.
When that happens, the firmware sends WMI_PEER_STA_KICKOUT_EVENTID event to the
host. Enable that to faster detect when a STA has left BSS without sending a
deauth frame.
Also set huge keepalive timeouts to avoid using the keepalive functionality in
the firmware.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable ap_ps_peer_param_cmdid for 10.x FW.
This is used mainly for AP UAPSD.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add set_bitrate_mask callback. Currently
ath10k HW is limited to handle only single
fixed rate setting or limit number of used
spatial streams.
Example:
iw wlanX set bitrates legacy-5 ht-mcs-5 vht-mcs-5 2:9
will setup VHT, nss=2, mcs=9
iw wlanX set bitrates legacy-5 18 ht-mcs-5 vht-mcs-5
will setup legacy, 18Mbps
iw wlanX set bitrates legacy-5 ht-mcs-5 3 vht-mcs-5
will setup HT, nss=1, mcs=3
iw wlanX set bitrate legacy-5 ht-mcs-5 vht-mcs-5 1:0-9
will setup nss=1
iw wlanX set bitrate legacy-5 ht-mcs-5 vht-mcs-5 1:0-9 2:0-9
will setup nss=2
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware dbglogs can be now enabled through fw_dbglog file. To enable all
possible log messages run:
echo 0xffffffff > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog
And to put back firmare defaults use 0x0:
echo 0x0 > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware can send simple ascii strings as debug messages using
WMI_DEBUG_PRINT_EVENTID, print those with ATH10K_DBG_WMI log level.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To not exceed number of allowed clients (AP mode), make sure to
check how many of them are already on the peers list.
10.X firmware support up to 127 peers, non-AP centric firmwares 16.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently ath10k is not using STA KICKOUT firmware functionality.
In order to avoid unwanted WMI_PEER_STA_KICKOUT_EVENT event this functionality
should be disabled when not used.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add Kconfig option that allow DFS functionality.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This value is no longer used by mac80211, and practically no
driver ever set it to a correct value anyway, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Not each ath10k FW track supports P2P (10.X for instance does not)
This new firmware feature flag allows to turn off P2P interface type.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Split the interface limits and inteface combination,
to reflect the 10.X capabilites (no P2P, no STA and 8 VAP).
kvalo: reverse order of ATH10K_FW_FEATURE_WMI_10X test, fix
checkpath warnings
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Although CCK modulation isn't expected for 11a if
it happened it made ath10k report wrong band
(2GHz) for a mgmt frame that were actually
received on 5Ghz band. Frequency would also
decoded incorrectly too.
In case of 5GHz-only devices this triggered
mac80211 WARN_ON because there was no according
sband pointer to be found.
The patch should fix delivery of such frames by
using different means to acquire band parameter.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We should check MIC error flag base on
rx_attention, to have consistent status
of MIC failure and FCS error.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Frames received from FW were treated incorrectly.
This led to stations being unable to associate to
WEP Shared ath10k AP. This was indicated by a
bizarre hostapd message:
Unsupported authentication algorithm (36088)
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
FW 10.1 seems to require the default key index to
be updated to point to group key after it is
installed. Otherwise Txed frames are corrupted.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Too much of tx info was being cleared. This caused
issues in some setups with tx frame status
reporting.
This should fix some cases of stations not being
able to associate to ath10k AP.
Reported-By: Matti Laakso <malaakso@elisanet.fi>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This can be useful for testing and debugging.
This introduces new ath10k_pci module parameter
`irq_mode`. By default it is 0, meaning automatic
irq mode (MSI-X as long as both target HW and host
platform supports it). The parameter works on a
best effort basis.
kvalo: fix typo "ayto"
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's possible for FW to panic during early boot.
The patch re-introduces support to detect and
print those crashes.
This introduces an additional irq handler that is
set for the duration of early boot and shutdown.
The handler is then overriden with regular
handlers upon hif start().
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Preparation for code re-use. Also use ioread/write
wrappers.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's impossible to rely on disable_irq() and/or CE
interrupt masking with legacy shared interrupts.
Other devices sharing the same irq line may assert
it while ath10k is doing something that requires
no interrupts.
Irq handlers are now registered after all
preparations are complete so spurious/foreign
interrupts won't do any harm. The handlers are
unregistered when no interrupts are required (i.e.
during driver teardown).
This also removes the ability to receive FW early
indication (since interrupts are not registered
until early boot is complete). This is not mission
critical (it's more of a hint that early boot
failed due to unexpected FW crash) and will be
re-added in a follow up patch.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The function did a couple of things: it allocated
CE completions, registered CE callbacks and
enabled CE interrupts through HW registers.
This cannot be so. Split the function into one
that allocates CE completions and the other one
that starts off CE operation.
This is required for future legacy shared
interrupt handling.
This also fixes possible memory leak if post rx
failed.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's not really necessary for interrupts to be
used for BMI. BMI already assumes there's only one
caller at a time and it works directly with CE.
Make BMI poll for CE completions instead of
waiting for interrupts. This makes disabling
interrupts during early boot possible.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Hardware waits until host signals whether it has
chosen MSI(-X) or shared legacy interrupts. It is
not required for the driver to register interrupt
handlers immediately.
This patch prepares the pci irq code for more
changes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k assumed all interrupts were directed to it.
This isn't the case for legacy shared interrupts.
ath10k consumed interrupts for other devices.
Check device irq status and return IRQ_NONE when
appropriate.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
These two flags are used for the same purpose, just
combine them into a no-ir flag to annotate no initiating
radiation is allowed.
Old userspace sending either flag will have it treated as
the no-ir flag. To be considerate to older userspace we
also send both the no-ir flag and the old no-ibss flags.
Newer userspace will have to be aware of older kernels.
Update all places in the tree using these flags with the
following semantic patch:
@@
@@
-NL80211_RRF_PASSIVE_SCAN
+NL80211_RRF_NO_IR
@@
@@
-NL80211_RRF_NO_IBSS
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_PASSIVE_SCAN
+IEEE80211_CHAN_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IBSS
+IEEE80211_CHAN_NO_IR
@@
@@
-NL80211_RRF_NO_IR | NL80211_RRF_NO_IR
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IR | IEEE80211_CHAN_NO_IR
+IEEE80211_CHAN_NO_IR
@@
@@
-(NL80211_RRF_NO_IR)
+NL80211_RRF_NO_IR
@@
@@
-(IEEE80211_CHAN_NO_IR)
+IEEE80211_CHAN_NO_IR
Along with some hand-optimisations in documentation, to
remove duplicates and to fix some indentation.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[do all the driver updates in one go]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We can show the same amount of information in one line. And then
it's easier to show this information only during first firmware boot
(see next patch).
For UART printouts there's already a message when they are enabled so
no need to have a print when they are disabled, that's the default
anyway.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Convert the MSI failure warnings to a debug message to make them less spammy.
Also convert the irq mode printout to a single print to make it easier to
show it only once.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sometimes for DFS testing is required to stay on current channel even after
radar detected. This patch allows to enable/disable radar detected event to be
passed to mac80211.
By default radar detected event in not blocked.
To block it:
echo 1 > /sys/kernel/debug/ieee80211/phyX/ath10k/dfs_block_radar_events
To unblock again:
echo 0 > /sys/kernel/debug/ieee80211/phyX/ath10k/dfs_block_radar_events
Inform about blocking radar detected event even when logs are disabled
for throughput/performance reasons.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Configure interface combination for AP running on channels
where radar detection is required. It allows only one type
of interface - AP on DFS channel and limits number of AP
interfaces to 8. Setup WMI channel flags accordingly to mac
channel configuration. CAC based on additional monitor vdev
is started if required for current channel.
kvalo: dropped ATH10K_DFS_CERTIFIED config option as this
the DFS still depends on few mac80211 and cfg80211 patches
which are on mac80211-next.git right now. The config option
will be added later once all dependencies are available.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Handle phyerr, dfs event, radar_report and fft_report.
Add also debugfs dfs_simulate_radar and dfs_stats files.
Use ath dfs pattern detector.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
Garbage was reported in ieee80211_tx_info. This
led to a WARN_ON in cfg80211_calculate_bitrate().
This also fixes some random tx bitrate values
reported through `iw` command.
Reported-By: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was obseverd many times the short queue limit can be
easily exceeded in case of AP multiple BSSID scenarios.
"ath10k: wmi mgmt_tx queue limit reached."
This was leading to TX packets drops.
This patch expands the queue limit to 128. After many stress
experiments (high traffic and lot of management frames in
the air) the new value seems to fix the problem on platforms
with limited resources.
Reported-By: Tomasz Skapski <tomasz.skapski@tieto.com>
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With commit 0cfcefef1 ("mac80211: support reporting A-MSDU subframes
individually") there's no need to have the hack to clear the retry bit in
ath10k_htt_rx_amsdu(), mac80211 can handle this properly now.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Frames were never retransmitted with
different/lower bandwidths, e.g. only 80MHz
bandwidth was used when dealing with a VHT80
peer.
Allow HW rate control to try out different
bandwidths when retransmitting. This increases
robustness.
Also, document the parameter properly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
HIF was not stopped properly in
ath10k_core_start() upon failure. This could cause
memory leaks of CE completions entries and
possibly other issues as well.
Move the HIF start/stop out of
ath10k_htc_wait_target(). The ctl_resp completion
is already prepared in ath10k_htc_init.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This should make sure the device won't issue any
interrupts nor access any memory after the driver
is stopped/freed thus avoid memory corruption in
some cases.
Reported-By: Ben Greear <greearb@candelatech.com>
Reported-By: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add missing error reporting and adjust other
prints to make everything more consistent.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch moves irq registering after necessary
structures have been allocated and initialized.
This should prevent interrupts from causing
tasklet access invalid memory pointers.
Reported-By: Ben Greear <greearb@candelatech.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case firmware crashes it may report CE
completions for entries that were never
submitted/filled with meaningful data. This in
turn led to NULL dereferences.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This shouldn't be silenced. This will be necessary
for PCI init code reordering.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This removes some remaining direct use of the wake
register which could interfere with power state
tracking of the target device. This will allow
initialization code reordering.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The check doesn't make much sense. If the address
were to be 0x0000 the check would fail. In this
case a 0 address isn't wrong.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make sure to put target back to sleep. This was a
minor issue as it didn't really matter if we put
target back to sleep at this point. It just looked
wrong.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
CE error interrupts were not disabled. This could
lead to invalid memory accesses / memory
corruption.
Also make sure CE watermark interrupts are also
disabled.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
What the function does is to actually wait for the
firmware indication bit to be set. Prerequisite
for this is having interrupts registered.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The function will soon be called from more than 1
place.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was possible for FW error tasklet to be
executed during teardown. This could lead to
system crashes and/or memory corruption.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It wasn't really useful to have it to begin with.
This makes it a little simpler to re-arrange PCI
init code as some function depended on
ar_pci->ce_count being set.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Not all errors were properly notified, fix that.
kvalo: use ath10k_warn() for all messages, cosmetic changes to some of the messages
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If the 'ar' registration fails early, the debug
objects were not initialized, and trouble ensued when
the object was later destroyed and the un-initialized
objects were accessed.
Per Kalle's suggestion, move the debug_destroy to the
core_unregister method.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
memory is malloced in ath10k_pci_probe() and should be freed before
leaving from the error handling cases, otherwise it will cause
memory leak.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If beacon tx command failed the wmi command buffer
was not freed. This led to OOM in the long run.
This became aparent when stress testing
multi-BSSID.
Reported-By: Tomasz Skapski <tomasz.skapski@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
sk_buff was not freed in some cases. The patch
unifies the msdu freeing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This allows txpower limits other than regulatory
to be applied (e.g. user txpower limit provided
via iw/nl80211).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was previously thought that FW expects tx power
in quarters of dBm.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
