v4l2_fh_init is already done. So call the v4l2_fh_exit in error
condition before returing from the function.
Signed-off-by: Shailendra Verma <shailendra.v@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Minor tweaks to document the swap register and make the documentation
match the struct ordering
Signed-off-by: Kieran Bingham <kieran@bingham.xyz>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The documentation for video capture and output devices claims that the video standard
ioctls are required. This is not the case, they are only required for PAL/NTSC/SECAM
type inputs and outputs. Sensors do not implement this at all and e.g. HDMI inputs
implement the DV Timings ioctls.
Just drop the mention of 'video standard' ioctls.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver moved to drivers/media/platform/atmel.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Update the bindings for this device based on a working DT example.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The colorspace is independent of whether YUV or RGB is sent to the SoC.
Fix this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Move this out of the soc_camera directory into the atmel directory
where it belongs.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch converts the atmel-isi driver from a soc-camera driver to a driver
that is stand-alone.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The original bindings documentation was incomplete (missing pinctrl-names,
missing endpoint node properties) and the example was out of date.
Add the missing information and tidy up the text.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add DT support. Use it to get the reset and pwdn pins (if there are any).
Tested with one sensor requiring reset/pwdn and one sensor that doesn't
have reset/pwdn pins.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Get the clock for this sensor.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Drop unnecesary memset. Drop the unnecessary extendedmode check and
set the V4L2_CAP_TIMEPERFRAME capability.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add v4l2-async support for this driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add binding documentation and add that file to the MAINTAINERS entry.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for Intel SR300 depth camera in uvc driver.
This includes adding three uvc GUIDs for the required pixel formats
and updating the uvc driver GUID-to-4cc tables with the new formats.
Signed-off-by: Daniel Patrick Johnson <teknotus@teknot.us>
Signed-off-by: Aviv Greenberg <avivgr@gmail.com>
Signed-off-by: Evgeni Raikhel <evgeni.raikhel@intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Provide the frame structure and data layout of V4L2-PIX-FMT-INZI
format utilized by Intel SR300 Depth camera.
Signed-off-by: Evgeni Raikhel <evgeni.raikhel@intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The statistics function subtracts two timespecs manually. A helper is
provided by the kernel to do this.
Replace the implementation, using the helper.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The frame counters are inadvertently counting packets with content as
empty.
Fix it by correcting the logic expression
Fixes: 7bc5edb00b [media] uvcvideo: Extract video stream statistics
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
All control menus use the english capitalization rules of titles.
The only menu not following these rules is the RGB Quantization Range control
menu. Fix this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Fixes: e0d3bafd02 ("V4L/DVB (10954): Add cx231xx USB driver")
Cc: stable <stable@vger.kernel.org> # 2.6.30
Cc: Sri Deevi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make sure to release the snd_card also on a late allocation error.
Fixes: e0d3bafd02 ("V4L/DVB (10954): Add cx231xx USB driver")
Cc: stable <stable@vger.kernel.org> # 2.6.30
Cc: Sri Deevi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Fixes: e0d3bafd02 ("V4L/DVB (10954): Add cx231xx USB driver")
Cc: stable <stable@vger.kernel.org> # 2.6.30
Cc: Sri Deevi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Fixes: 2a9f8b5d25 ("V4L/DVB (5206): Usbvision: set alternate interface
modification")
Cc: stable <stable@vger.kernel.org> # 2.6.21
Cc: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: c4018fa2e4 ("[media] dib0700: fix RC support on Hauppauge
Nova-TD")
Cc: stable <stable@vger.kernel.org> # 3.16
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The V4L2_INPUT_TYPE_CAMERA and V4L2_OUTPUT_TYPE_ANALOG descriptions were
hopelessly out of date. Fix this, and also fix a few style issues in these
documents. Finally add the missing documentation for V4L2_OUTPUT_TYPE_ANALOGVGAOVERLAY
(only used by the zoran driver).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Most ioctls do not have to write back the contents of the argument
if an error is returned. But VIDIOC_S_EDID is an exception together
with the EXT_CTRLS ioctls (already handled correctly).
Add this exception to v4l2-compat-ioctl32.
This fixes a compliance error when using compat32 and trying to
set a new EDID with more blocks than the hardware supports. In
that case the driver will return -E2BIG and set edid.blocks to the
actual maximum number of blocks. This field was never copied back
to userspace due to this bug.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the line "Camera sensors are also considered to be a video input."
In practice all non-MC drivers for sensors support the input ioctls, and the
compliance test actually tests for the presence of these ioctls. So clarify
the documentation by explicitly mentioning sensors.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When CONFIG_PM is disabled, we get a couple of unused functions:
drivers/media/platform/mtk-jpeg/mtk_jpeg_core.c:927:13: error: 'mtk_jpeg_clk_off' defined but not used [-Werror=unused-function]
static void mtk_jpeg_clk_off(struct mtk_jpeg_dev *jpeg)
^~~~~~~~~~~~~~~~
drivers/media/platform/mtk-jpeg/mtk_jpeg_core.c:916:13: error: 'mtk_jpeg_clk_on' defined but not used [-Werror=unused-function]
static void mtk_jpeg_clk_on(struct mtk_jpeg_dev *jpeg)
Rather than adding more error-prone #ifdefs around those, this patch
removes the existing #ifdef checks and marks the PM functions as __maybe_unused
to let gcc do the right thing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rick Chang <rick.chang@mediatek.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
According to the surrounding goto, it is likely that 'unprep_clk_gate'
was expected here.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Further investigation revealed that codec buffers also don't need to
be allocated at higher addresses than firmware base for MFC v6+ hardware.
Those buffers can be quite large and its size depends on the selected
format and framesize. This patch changes the way the codec buffers are
allocated - driver will use generic allocator for them instead of the
pre-allocated buffer for firmware and contexts.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Clock should be turned off after calling s5p_mfc_init_hw() from the
watchdog worker, like it is already done in the s5p_mfc_open() which also
calls this function.
Fixes: af93574678 ("[media] MFC: Add MFC 5.1 V4L2 driver")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: stable@vger.kernel.org # v3.7+
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Documentation for MFC hardware still uses 'left' and 'right' names for
the memory channel/banks, so replace BANK1/2 defines with more appropriate
BANK_L/R names.
Suggested-by: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It turned out that all versions of MFC v6+ hardware doesn't have a strict
requirement for ALL buffers to be allocated on higher addresses than the
firmware base like it was documented for MFC v5. This requirement is true
only for the device and per-context buffers. All video data buffers can be
allocated anywhere for all MFC v6+ versions. Basing on this fact, the
special DMA configuration based on two reserved memory regions is not
really needed for MFC v6+ devices, because the memory requirements for the
firmware, device and per-context buffers can be fulfilled by the simple
probe-time pre-allocated block allocator introduced in previous patch.
This patch enables support for such pre-allocated block based allocator
always for MFC v6+ devices. Due to the limitations of the memory management
subsystem the largest supported size of the pre-allocated buffer when no
CMA (Contiguous Memory Allocator) is enabled is 4 MiB.
This patch also removes the requirement to provide two reserved memory
regions for MFC v6+ devices in device tree. Now the driver is fully
functional without them.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The main reason for using special configuration of IOMMU domain was the
problem with MFC firmware, which failed to operate properly when placed
at 0 DMA address. Instead of adding custom code for configuring each
variant of IOMMU domain and architecture specific glue code, simply use
what arch code provides and if the DMA base address equals zero, skip
first 128 KiB to keep required alignment. This patch also make the driver
operational on ARM64 architecture, because it no longer depends on ARM
specific DMA-mapping and IOMMU glue code functions.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Current MFC driver depends on the fact that when IOMMU is available, the
DMA-mapping framework and its IOMMU glue will use first-fit allocator.
This was true for ARM architecture, but its not for ARM64 arch. However, in
case of MFC v6+ hardware and latest firmware, it turned out that there is
no strict requirement for ALL buffers to be allocated on higher addresses
than the firmware base. This requirement is true only for the device and
per-context buffers. All video data buffers can be allocated anywhere for
all MFC v6+ versions.
Such relaxed requirements for the memory buffers can be easily fulfilled
by allocating firmware, device and per-context buffers from the probe-time
preallocated larger buffer. This patch adds support for it. This way the
driver finally works fine on ARM64 architecture. The size of the
preallocated buffer is 8 MiB, what is enough for three instances H264
decoders or encoders (other codecs have smaller memory requirements).
If one needs more for particular use case, one can use "mem" module
parameter to force larger (or smaller) buffer (for example by adding
"s5p_mfc.mem=16M" to kernel command line).
[mchehab@s-opensource.com: fix two checkpatch warnings: don't initialize
static to NULL; don't use S_foo permisions]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Move code for DMA memory configuration with IOMMU into separate function
to make it easier to compare what is being done in each case.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Firmware for MFC v6+ variants is not larger than 400 KiB, so there is no
need to allocate a full 1 MiB buffer for it. Reduce it to 512 KiB to keep
proper alignment of allocated buffer.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Once firmware buffer has been converted to use s5p_mfc_priv_buf structure,
it is possible to allocate it with existing s5p_mfc_alloc_priv_buf()
function. This change will help to reduce code variants in the next
patches.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
To complete DMA memory configuration for MFC device, allocation of the
firmware buffer is needed, because some parameters are dependant on its base
address. Till now, this has been handled in the s5p_mfc_alloc_firmware()
function. This patch moves that logic to s5p_mfc_configure_dma_memory() to
keep DMA memory related operations in a single place. This way
s5p_mfc_alloc_firmware() is simplified and does what it name says. The
other consequence of this change is moving s5p_mfc_alloc_firmware() call
from the s5p_mfc_probe() function to the s5p_mfc_configure_dma_memory().
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use s5p_mfc_priv_buf structure for keeping the firmware image. This will
help handling of firmware buffer allocation in the next patches.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Setting DMA max segment size to 32 bit mask is a part of DMA memory
configuration, so move those calls to s5p_mfc_configure_dma_memory()
function.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Change parameters for s5p_mfc_alloc_priv_buf() and s5p_mfc_release_priv_buf()
functions. Instead of DMA device pointer and a base, provide common MFC
device structure and memory bank context identifier.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Internal MFC driver device structure contains two entries for keeping
addresses of the DMA memory banks. Replace them with the dma_base[] array
and use defines for accessing particular banks. This will help to simplify
code in the next patches.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Internal MFC driver device structure contains two pointers to devices used
for DMA memory allocation: mem_dev_l and mem_dev_r. Replace them with the
mem_dev[] array and use defines for accessing particular banks. This will
help to simplify code in the next patches.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove unused structures, definitions and functions
that are no longer called from the driver code.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Reviewed-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Interrupt routine must wake process waiting for given interrupt AFTER
updating driver's internal structures and contexts. Doing it in-between
is a serious bug. This patch moves all calls to the wake() function to
the end of the interrupt processing block to avoid potential and real
races, especially on multi-core platforms. This also fixes following issue
reported from clock core (clocks were disabled in interrupt after being
unprepared from the other place in the driver, the stack trace however
points to the different place than s5p_mfc driver because of the race):
WARNING: CPU: 1 PID: 18 at drivers/clk/clk.c:544 clk_core_unprepare+0xc8/0x108
Modules linked in:
CPU: 1 PID: 18 Comm: kworker/1:0 Not tainted 4.10.0-next-20170223-00070-g04e18bc99ab9-dirty #2154
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
Workqueue: pm pm_runtime_work
[<c010d8b0>] (unwind_backtrace) from [<c010a534>] (show_stack+0x10/0x14)
[<c010a534>] (show_stack) from [<c033292c>] (dump_stack+0x74/0x94)
[<c033292c>] (dump_stack) from [<c011cef4>] (__warn+0xd4/0x100)
[<c011cef4>] (__warn) from [<c011cf40>] (warn_slowpath_null+0x20/0x28)
[<c011cf40>] (warn_slowpath_null) from [<c0387a84>] (clk_core_unprepare+0xc8/0x108)
[<c0387a84>] (clk_core_unprepare) from [<c0389d84>] (clk_unprepare+0x24/0x2c)
[<c0389d84>] (clk_unprepare) from [<c03d4660>] (exynos_sysmmu_suspend+0x48/0x60)
[<c03d4660>] (exynos_sysmmu_suspend) from [<c042b9b0>] (pm_generic_runtime_suspend+0x2c/0x38)
[<c042b9b0>] (pm_generic_runtime_suspend) from [<c0437580>] (genpd_runtime_suspend+0x94/0x220)
[<c0437580>] (genpd_runtime_suspend) from [<c042e240>] (__rpm_callback+0x134/0x208)
[<c042e240>] (__rpm_callback) from [<c042e334>] (rpm_callback+0x20/0x80)
[<c042e334>] (rpm_callback) from [<c042d3b8>] (rpm_suspend+0xdc/0x458)
[<c042d3b8>] (rpm_suspend) from [<c042ea24>] (pm_runtime_work+0x80/0x90)
[<c042ea24>] (pm_runtime_work) from [<c01322c4>] (process_one_work+0x120/0x318)
[<c01322c4>] (process_one_work) from [<c0132520>] (worker_thread+0x2c/0x4ac)
[<c0132520>] (worker_thread) from [<c0137ab0>] (kthread+0xfc/0x134)
[<c0137ab0>] (kthread) from [<c0107978>] (ret_from_fork+0x14/0x3c)
---[ end trace 1ead49a7bb83f0d8 ]---
Fixes: af93574678 ("[media] MFC: Add MFC 5.1 V4L2 driver")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: stable@vger.kernel.org # v4.5+
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix s5p_mfc_set_dec_frame_buffer_v6() to print buffer pointer in hex
to be consistent with the rest of the messages in the routine.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Initialize members of the internal device and context structures as early
as possible to avoid access to uninitialized objects on initialization
failures. If loading firmware or creating of the hardware instance fails,
driver will access device or context queue in error handling path, which
might not be initialized yet, what causes kernel panic. Fix this by moving
initialization of all static members as early as possible.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
