The Broadcom BCM7445 STB chip has an issued in its revision D0 which was
previously worked around in drivers/net/dsa/bcm_sf2.c where we may
end-up double programming the integrated BCM7445 switch (bcm_sf2) and an
external Broadcom switch such as BCM53125, since these are mostly
register compatible.
Add a small quirk which just defers probing until we are sitting on the
slave DSA MDIO bus, which will allow us to intercept reads/writes and
funnel them through the SF2 internal MDIO master (which happens to
disconnect its pseudo PHY).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for Broadcom's BCM53xx switch family, also known
as RoboSwitch. Some of these switches are ubiquituous, found in home
routers, Wi-Fi routers, DSL and cable modem gateways and other
networking related products.
This drivers adds the library driver (b53_common.c) as well as a few bus
glue drivers for MDIO, SPI, Switch Register Access Block (SRAB) and
memory-mapped I/O into a SoC's address space (Broadcom BCM63xx/33xx).
Basic operations are supported to bring the Layer 1/2 up and running,
but not much more at this point, subsequent patches add the remaining
features.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring VLANs on the Broadcom Starfigther2 switch.
This is all done through the bridge vlan facility just like other DSA
drivers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the definitions for the VLAN registers that we are going to
manipulate in subsequent patches.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-order the bcm_sf2_sw_setup() function so that it is at the far end of
the driver to avoid any kind of forward declarations.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper function to fast age something that is controlled by the
caller: port, VLAN. We will use this to implement a VLAN fast age
operation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register a slave MDIO bus which allows us to divert problematic
read/writes towards conflicting pseudo-PHY address (30). Do no longer
rely on DSA's slave_mii_bus, but instead provide our own implementation
which offers more flexibility as to what to do, and when to register it.
We need to register it by the time we are able to get access to our
memory mapped registers, which is not until drv->setup() time. In order
to avoid forward declarations, we need to re-order the function bodies a
bit.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing DSA binding has a number of limitations and problems. The
main problem is that it cannot represent a switch as a linux device,
hanging off some bus. It is limited to one CPU port. The DSA platform
device is artificial, and does not really represent hardware.
Implement a new binding which can be embedded into any type of node on
a bus to represent one switch device, and its links to other switches.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have the switch driver register its own MDIO bus. This allows for an
mdio property in the device tree, with child nodes for phys, which
can be referenced via phandles, etc.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch implements a generic MDIO bus, which could host more than
PHYs. It is conventional to use _mdio_ or _mii_ in the function name,
so rename them. Also postfix make the historically first read/write
function with _direct, to help distinguish it from _indirect and _ppu.
While touching these functions, remove some of the _ prefixes, which
we are deprecating.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The merged driver no longer offers the option to use DSA tagging. So
remove the code to setup the switch to do DSA tagging and hard code
the use of EDSA.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>y
Signed-off-by: David S. Miller <davem@davemloft.net>
The new binding will not have a chip data structure, it will place the
routing directly into the switch structure. To enable backwards
compatibility, copy the routing from the chip data into the switch
structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With a maximum of four switches, the size of the routing table is the
same as the pointer to it. Removing it makes the code simpler.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are going to be more per-port members added to the switch
structure. So add a port structure and move the netdev into it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the bridge code defers the switchdev port state setting, there
is no need to defer the port STP state change within the mv88e6xxx code.
Thus get rid of the driver's bridge work code.
This also fixes a race condition where the DSA layer assumes that the
bridge code already set the unbridged port's STP state to Disabled
before restoring the Forwarding state.
As a consequence, this also fixes the FDB flush for the unbridged port
which now correctly occurs during the Forwarding to Disabled transition.
Fixes: 0bc05d585d ("switchdev: allow caller to explicitly request attr_set as deferred")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A switch can export an attached EEPROM using the standard ethtool API.
However the switch itself cannot determine the size of the EEPROM, and
multiple sizes are allowed. Thus a device tree property is supported
to indicate the length of the EEPROM. Parse this property during
device probe, and implement a callback function to retrieve it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_switch structure contains a dsa_chip_data member called pd.
However in the rest of the code, pd is used for dsa_platform_data.
This is confusing. Rename it cd, which is already often used in dsa.c
and slave.c for this data type.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch drivers only use the master_dev member for dev_info()
messages. Now that the device is passed to the old style probe, and
new style drivers are probed as true linux drivers, this is no longer
needed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resetting the switch is something the driver does, not the framework.
So move the parsing of this property into the driver.
There are no in kernel users of this property, so moving it does not
break anything. There is however a board which will make use of this
property making its way into the kernel.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow Marvell switches to be mdio devices. Currently the driver just
allocate the private structure and detects what device is on the
bus. Later patches will make them register with the DSA framework.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
All other DSA drivers use _drv_ in there DSA probe function name, thus
allowing for a true linux driver probe function to use the
conventional name. Make mv88e6xxx fit this pattern.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
By initialising immediately it, we don't run the danger of using it
before it is initialised.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some switch models have a STU (per VLAN port state database). Add a new
capability flag to switches info, instead of checking their family.
Also if the 6165 family has an STU, it must have a VTU, so add the
MV88E6XXX_FLAG_VTU to its family flags.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both VTU and STU operations use the same routine to access their
(common) data registers, with a different offset.
Add VTU and STU specific read and write functions to the data registers
to abstract the required offset.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all drivers support the same set of functions and the same
setup code, drop every model-specific DSA switch driver and replace them
with a common mv88e6xxx driver.
This merges the info tables into one, removes the function exports, the
model-specific files, and update the defconfigs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6131 is the only driver to set the tag protocol to DSA_TAG_PROTO_DSA.
Since it works fine with DSA_TAG_PROTO_EDSA, change its value, like all
other mv88e6xxx drivers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a shared mv88e6xxx_setup function to the drivers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6131 is the only driver which setups the priority of IGMP/MLD snoop
frames and ARP frames to the highest setting. Drop such change until we
figure out a common configuration for all switch models.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All switch models setup the GLOBAL_CONTROL_2 register with slightly
differences.
Since the cascade mode is valid even in a single chip setup, factorize
such configuration.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All switch drivers configure the GLOBAL_MONITOR_CONTROL register with
slightly changes.
Assume the setup of the upstream port, and configure it as the port to
which ingress and egress and ARP monitor frames are to be sent.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6131 switch models have a Core Tag Type register. Their setup code
is setting it to 0x8100, which is the reset default.
Drop this specific part which is correctly configured on reset anyway.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All switch models configure the GLOBAL_CONTROL register with slightly
differences.
Discarding packets with excessive collisions
(GLOBAL_CONTROL_DISCARD_EXCESS) is specific to 6352 and similar
switches, and setting a maximum frame size
(GLOBAL_CONTROL_MAX_FRAME_1632) is specific to 6185 and similar
switches.
As we are centralizing the chips setup, skip these settings and don't
discard any frames yet, until we found out that such discarding by the
hardware is necessary.
Assume a common setup to enable the PHY Polling Unit if present, don't
discard any packets, and mask all interrupt sources.
Tested on 88E6352 and 88E6185.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every driver is calling mv88e6xxx_setup_global after
mv88e6xxx_setup_common. Call the former in the latter.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a MV88E6XXX_FLAG_PPU_ACTIVE flag to describe how to reset the
switch, and merge the reset call to the common setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a MV88E6XXX_FLAG_ATU flag to identify switch models with an Address
Translation Unit.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a MV88E6XXX_FLAG_VTU flag to indentify switch models with a VLAN
Table Unit.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MV88E6XXX_FLAG_PORTSTATE and MV88E6XXX_FLAG_VLANTABLE flags to
identify switch models with required 802.1D operations.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only 6131 was not supporting the port registers access yet. Assume such
support and use the unlock access routines in the meantime.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a MV88E6XXX_FLAG_EEE flag to describe switch models featuring Energy
Efficient Ethernet. Use it to conditionally support such access in the
common code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some switch models have a dedicated register for Switch MAC/WoF/WoL.
This register, when present, is used to indirectly set the switch MAC
address, instead of a direct write to 3 global registers.
Identify this feature and share a common mv88e6xxx_set_addr function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MV88E6XXX_FLAG_TEMP and MV88E6XXX_FLAG_TEMP_LIMIT flags to describe
switch models featuring a temperature access. Use them to centralize the
access to the temperature feature.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a MV88E6XXX_FLAG_EEPROM flag to describe switch models featuring an
EEPROM and distribute the EEPROM access routines to all models.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some switch has dedicated SMI PHY Command and Data registers, used to
indirectly access the PHYs, instead of direct access.
Identify these switch models and make mv88e6xxx_phy_{read,write} generic
enough to support every models.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a MV88E6XXX_FLAG_PPU flag to describe switch models with a PHY
Polling Unit. This allows to merge PPU specific PHY access code in the
share code.
Make the mv88e6xxx_ppu_disable and mv88e6xxx_phy_{read,write}_ppu
functions use unlocked register accesses in order to call them in
mv88e6xxx_phy_{read,write} in a locked context.
Since the PPU code is shared, also remove NET_DSA_MV88E6XXX_NEED_PPU.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a flags bitmap to the info structure in order to identify features
supported or not by the different switch models.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv4/ip_gre.c
Minor conflicts between tunnel bug fixes in net and
ipv6 tunnel cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_switch structure ds is actually needed in very few places,
mostly during setup of the switch. The private structure ps is however
needed nearly everywhere. Pass ps, not ds internally.
[vd: rebased Andrew's patch.]
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error return err is not initialized and there is a possibility
that err is not assigned causing mv88e6xxx_port_bridge_join to
return a garbage error return status. Fix this by initializing err
to 0.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts were two cases of simple overlapping changes,
nothing serious.
In the UDP case, we need to add a hlist_add_tail_rcu()
to linux/rculist.h, because we've moved UDP socket handling
away from using nulls lists.
Signed-off-by: David S. Miller <davem@davemloft.net>
ps->id is not needed anymore, so remove it as well as the related
defined values.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the number of databases to the info structure.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop the ps->num_ports variable in favor of a new member of the info
structure. This removes the need to assign it at setup time.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an mv88e6xxx_family enum to the info structure for better family
indentification.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new switch info structure which is meant to store switch models
static information, such as product number, name, number of ports,
number of databases, etc.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read the switch ID only once, at probe time, to avoid multiple read
accesses and MII bus checking.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point in having a special case for the revision when probing
a switch model. The code gets cluttered with unnecessary defines, and
leads to errors when code such as mv88e6131_setup compares
PORT_SWITCH_ID_6131_B2 to ps->id which masks the revision.
Drop every revision definition, and lookup only the product number.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every driver assigns ps->ds even though it gets assigned in the shared
mv88e6xxx_setup_common function. Kill redundancy.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the dsa_switch_driver.probe function to return a const char *.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros hide a ds variable and a return statement on error, which
can lead to locking issues. Kill them off.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For hardware cross-chip bridging to work, user ports *and* DSA ports
need to share a common address database, in order to switch a frame to
the correct interconnected device.
This is currently working for VLAN filtering aware systems, since Linux
will implement a bridge group as a 802.1Q VLAN, which has its own FDB,
including DSA and CPU links as members.
However when the system doesn't support VLAN filtering, Linux only
relies on the port-based VLAN to implement a bridge group.
To fix hardware cross-chip bridging for such systems, set the same
default address database 0 for user and DSA ports, instead of giving
them all a different default database.
Note that the bridging code prevents frames to egress between unbridged
ports, and flushes FDB entries of a port when changing its STP state.
Also note that the FID 0 is special and means "all" for ATU operations,
but it's OK since it is used as a default forwarding address database.
Fixes: 2db9ce1fd9 ("net: dsa: mv88e6xxx: assign default FDB to ports")
Fixes: 466dfa0770 ("net: dsa: mv88e6xxx: assign dynamic FDB to bridges")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In multi-chip systems, DSA Tag ports must learn SA addresses in order to
correctly switch frames between interconnected chips.
This fixes cross-chip hardware bridging in a VLAN filtering aware
system, because a bridge group gets implemented as an hardware 802.1Q
VLAN and thus DSA and user ports share the same FDB.
Fixes: 4c7ea3c079 ("net: dsa: mv88e6xxx: disable SA learning for DSA and CPU ports")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Locking a port generates an hardware interrupt when a new SA address is
received. This enables CPU directed learning, which is needed for 802.1X
MAC authentication.
To disable automatic learning on a port, the only configuration needed
is to set its Port Association Vector to all zero.
Clear PAV when SA learning should be disabled instead of locking a port.
Fixes: 4c7ea3c079 ("net: dsa: mv88e6xxx: disable SA learning for DSA and CPU ports")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_lookup_name() returns the model name of a switch at a given
address on an MII bus. Using mii_bus to identify the bus rather than
the host device is more logical, so change the parameter.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phys in phys_port_mask suggests this mask is about PHYs. In fact,
it means physical ports. Rename to enabled_port_mask, indicating
external enabled ports of the switch, which is hopefully less
confusing.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the function called from the DSA to perform a probe for the
switch. This makes the normal _probe() name available for a standard
Linux device driver probe function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than looking up the mii bus and address every time, do it once
at probe, and keep it in the private structure. Centralise this probe
code in mv88e6xxx.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the switch devices have a dev pointer, make use of it for allocating
the drivers private data structures using a devm_kzalloc().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By passing a device structure to the switch devices, it allows them
to use devm_* methods for resource management.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switchdev design implies that a software error should not happen in
the commit phase since it must have been previously reported in the
prepare phase. If an hardware error occurs during the commit phase,
there is nothing switchdev can do about it.
The DSA layer separates port_vlan_prepare and port_vlan_add for
simplicity and convenience. If an hardware error occurs during the
commit phase, there is no need to report it outside the driver itself.
Make the DSA port_vlan_add routine return void for explicitness.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switchdev design implies that a software error should not happen in
the commit phase since it must have been previously reported in the
prepare phase. If an hardware error occurs during the commit phase,
there is nothing switchdev can do about it.
The DSA layer separates port_fdb_prepare and port_fdb_add for simplicity
and convenience. If an hardware error occurs during the commit phase,
there is no need to report it outside the DSA driver itself.
Make the DSA port_fdb_add routine return void for explicitness.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA layer doesn't care about the return code of the port_stp_update
routine, so make it void in the layer and the DSA drivers.
Replace the useless dsa_slave_stp_update function with a
dsa_slave_stp_state function used to reply to the switchdev
SWITCHDEV_ATTR_ID_PORT_STP_STATE attribute.
In the meantime, rename port_stp_update to port_stp_state_set to
explicit the state change.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By adding support for bridge operations, FDB operations, and optionally
VLAN operations (for 802.1Q and VLAN filtering aware systems), the
switch bridges ports correctly, the CPU is able to populate the hardware
address databases, and thus hardware bridging becomes functional within
the 88E6185 family of switches.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88E6185 switch also has a MapDA bit in its Port Control 2 register.
When this bit is cleared, all frames are sent out to the CPU port.
Set this bit to rely on address databases (ATU) hits and direct frames
out of the correct ports, and thus allow hardware bridging.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6185 family of devices has only 256 address databases. Their 8-bit
FID for ATU and VTU operations are split into ATU Control and ATU/VTU
Operation registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell switch chips have different number of address databases.
The code currently only supports models with 4096 databases. Such switch
has dedicated FID registers for ATU and VTU operations. Models with
fewer databases have their FID split in several registers.
List them all but only support models with 4096 databases at the moment.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only switch families with 4096 address databases have dedicated FID
registers for ATU and VTU operations.
Factorize the access to the GLOBAL_ATU_FID register and introduce a
mv88e6xxx_has_fid_reg() helper function to protect the access to
GLOBAL_ATU_FID and GLOBAL_VTU_FID.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a mv88e6xxx_has_stu() helper to protect the access to the
GLOBAL_VTU_SID register, instead of checking switch families.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the vendor-specific bootloaders set up this part
of the initialization for us, so this was never added.
However, since upstream bootloaders don't initialize the
chip specifically, they leave the fiber MII's PDOWN flag
set, which means that the CPU port doesn't connect.
This patch checks whether this flag has been clear prior
by something else, and if not make us clear it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Patrick Uiterwijk <patrick@puiterwijk.org>
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add versions of the phy_page_read and _write functions to
be used in a context where the SMI mutex is held.
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Patrick Uiterwijk <patrick@puiterwijk.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev_upper_dev_unlink() which notifies NETDEV_CHANGEUPPER, returns
void, as well as del_nbp(). So there's no advantage to catch an eventual
error from the port_bridge_leave routine at the DSA level.
Make this routine void for the DSA layer and its existing drivers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename DSA port_join_bridge and port_leave_bridge routines to
respectively port_bridge_join and port_bridge_leave in order to respect
an implicit Port::Bridge namespace.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the drivers support multiple chips, but mv88e6123_61_65 is the
only one that reflects this in its naming. Change it to be consistent
with the other drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to change the 802.1Q port mode for the same value.
Thus avoid such message:
[ 401.954836] dsa dsa@0 lan0: 802.1Q Mode: Disabled (was Disabled)
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port register 0x07 contains more options than just the default VID,
even though they are not used yet. So prefer a read then write operation
over a direct write.
This also allows to keep track of the change through dynamic debug.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apply a few non-functional changes on the port state setter:
* add a dynamic debug message with state names to track changes
* explicit states checking instead of assuming their numeric values
* lock mutex only once when changing several port states
* use bitmap macros to declare and access port_state_update_mask
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement port_vlan_filtering in the driver to toggle the related port
802.1Q mode between DISABLED and SECURE, on user request.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that ports isolation is correctly configured when joining or leaving
a bridge, there is no need to rely on reserved VLANs to isolate
unbridged ports anymore. Thus remove them, and disable 802.1Q on setup.
This restores the expected behavior of hardware bridging for systems
without 802.1Q or VLAN filtering enabled.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The In Chip Port Based VLAN Table contains bits used to restrict which
output ports this input port can send frames to.
With the VLAN filtering enabled, these tables work in conjunction with
the VLAN Table Unit to allow egressing frames.
In order to remove the current dependency to BRIDGE_VLAN_FILTERING for
basic hardware bridging to work, it is necessary to restore a fine
control of each port's VLANTable, on setup and when a port joins or
leaves a bridge.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Give a new bridge a fresh FDB, assign it to its members, and restore a
fresh FDB to a port leaving a bridge.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restore per-port FDB. Assign them on setup, allow adding and deleting
addresses into them, and dump them.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a _mv88e6xxx_fid_new function which gives and flushes the lowest FID
available. Call it when preparing a new VTU entry.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move out the code which dumps a single FDB to its own function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename _mv88e6xxx_vlan_init in _mv88e6xxx_vtu_new, eventually called
from a new _mv88e6xxx_vtu_get function, which abstracts the VTU GetNext
VID-1 trick to retrieve a single entry.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the port_pvid_get and vlan_getnext functions in favor of a
simpler mv88e6xxx_port_vlan_dump function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA drivers now have access to the VLAN prepare phase and the bridge
net_device. It is easier to check for overlapping bridges from within
the driver. Thus add such check in mv88e6xxx_port_vlan_prepare.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some DSA drivers may or may not support multiple software bridges on top
of an hardware switch.
It is more convenient for them to access the bridge's net_device for
finer configuration.
Removing the need to craft and access a bitmask also simplifies the
code.
This patch changes the signature of bridge related functions, update DSA
drivers, and removes dsa_slave_br_port_mask.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a per-port mv88e6xxx_priv_port structure to store per-port related
data, instead of adding several arrays of DSA_MAX_PORTS elements in the
mv88e6xxx_priv_state structure.
It currently only contains the port STP state.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 88E6240 has been tested successfully without further
changes. Add entry to the table of supported devices.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
BRIDGE_VLAN_FILTERING automatically adds a newly bridged port to the
VLAN with the bridge's default_pvid.
The mv88e6xxx driver currently reserves VLANs 4000+ for unbridged ports
isolation. When a port joins a bridge, it leaves its reserved VLAN. When
a port leaves a bridge, it joins again its reserved VLAN.
But if the VLAN filtering is disabled, or if this hardware VLAN is
already in use, the bridged port ends up with no default VLAN, and the
communication with the CPU is thus broken.
To fix this, make a port join its reserved VLAN once on setup, never
leave it, and restore its PVID after another one was eventually used.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
