This patch adds the WDIOF_CARDRESET support for the Renesas platform
watchdog, to know if the board reboot is due to a watchdog reset.
This is done via the WOVF bit (bit 4) of the RWTCSRA register, which
indicates if RWTCNT overflowed, triggering the reset in last boot.
Signed-off-by: Veeraiyan Chidambaram <veeraiyan.chidambaram@in.bosch.com>
[takeshi.kihara.df: changed to read the RWTCSRA register while clock is
enabled]
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case I replaced "Fall" with a proper
"Fall through" comment, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case I replaced "Fall" with a proper
"Fall through" comment, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case I replaced "Fall" with a proper
"Fall through" comment, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
New drivers:
- Nintendo Wii GameCube GPIO, known as "Hollywood"
- Raspberry Pi mailbox service GPIO expander
- Spreadtrum main SC9860 SoC and IEC GPIO controllers.
Improvements:
- Implemented .get_multiple() callback for most of the
high-performance industrial GPIO cards for the ISA bus.
- ISA GPIO drivers now select the ISA_BUS_API instead of
depending on it. This is merged with the same pattern
for all the ISA drivers and some other Kconfig cleanups
related to this.
Cleanup:
- Delete the TZ1090 GPIO drivers following the deletion of
this SoC from the ARM tree.
- Move the documentation over to driver-api to conform with
the rest of the kernel documentation build.
- Continue to make the GPIO drivers include only
<linux/gpio/driver.h> and not the too broad <linux/gpio.h>
that we want to get rid of.
- Managed to remove VLA allocation from two drivers pending
more fixes in this area for the next merge window.
- Misc janitorial fixes.
-----BEGIN PGP SIGNATURE-----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=C5t5
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.17 kernel cycle:
New drivers:
- Nintendo Wii GameCube GPIO, known as "Hollywood"
- Raspberry Pi mailbox service GPIO expander
- Spreadtrum main SC9860 SoC and IEC GPIO controllers.
Improvements:
- Implemented .get_multiple() callback for most of the
high-performance industrial GPIO cards for the ISA bus.
- ISA GPIO drivers now select the ISA_BUS_API instead of depending on
it. This is merged with the same pattern for all the ISA drivers
and some other Kconfig cleanups related to this.
Cleanup:
- Delete the TZ1090 GPIO drivers following the deletion of this SoC
from the ARM tree.
- Move the documentation over to driver-api to conform with the rest
of the kernel documentation build.
- Continue to make the GPIO drivers include only
<linux/gpio/driver.h> and not the too broad <linux/gpio.h> that we
want to get rid of.
- Managed to remove VLA allocation from two drivers pending more
fixes in this area for the next merge window.
- Misc janitorial fixes"
* tag 'gpio-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (77 commits)
gpio: Add Spreadtrum PMIC EIC driver support
gpio: Add Spreadtrum EIC driver support
dt-bindings: gpio: Add Spreadtrum EIC controller documentation
gpio: ath79: Fix potential NULL dereference in ath79_gpio_probe()
pinctrl: qcom: Don't allow protected pins to be requested
gpiolib: Support 'gpio-reserved-ranges' property
gpiolib: Change bitmap allocation to kmalloc_array
gpiolib: Extract mask allocation into subroutine
dt-bindings: gpio: Add a gpio-reserved-ranges property
gpio: mockup: fix a potential crash when creating debugfs entries
gpio: pca953x: add compatibility for pcal6524 and pcal9555a
gpio: dwapb: Add support for a bus clock
gpio: Remove VLA from xra1403 driver
gpio: Remove VLA from MAX3191X driver
gpio: ws16c48: Implement get_multiple callback
gpio: gpio-mm: Implement get_multiple callback
gpio: 104-idi-48: Implement get_multiple callback
gpio: 104-dio-48e: Implement get_multiple callback
gpio: pcie-idio-24: Implement get_multiple/set_multiple callbacks
gpio: pci-idio-16: Implement get_multiple callback
...
This removes the entire architecture code for blackfin, cris, frv, m32r,
metag, mn10300, score, and tile, including the associated device drivers.
I have been working with the (former) maintainers for each one to ensure
that my interpretation was right and the code is definitely unused in
mainline kernels. Many had fond memories of working on the respective
ports to start with and getting them included in upstream, but also saw
no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company
in charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It seems
that all the SoC product lines are still around, but have not used the
custom CPU architectures for several years at this point. In contrast,
CPU instruction sets that remain popular and have actively maintained
kernel ports tend to all be used across multiple licensees.
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I made
sure that they are all unused. Some architectures (notably tile, mn10300,
and blackfin) are still being shipped in products with old kernels,
but those products will never be updated to newer kernel releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing their
support or getting it added to mainline gcc in the first place.
They all have patched gcc-7.3 ports that work to some degree, but
complete upstream support won't happen before gcc-8.1. Csky posted
their first kernel patch set last week, their situation will be similar.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJawdL2AAoJEGCrR//JCVInuH0P/RJAZh1nTD+TR34ZhJq2TBoo
PgygwDU7Z2+tQVU+EZ453Gywz9/NMRFk1RWAZqrLix4ZtyIMvC6A1qfT2yH1Y7Fb
Qh6tccQeLe4ezq5u4S/46R/fQXu3Txr92yVwzJJUuPyU0arF9rv5MmI8e6p7L1en
yb74kSEaCe+/eMlsEj1Cc1dgthDNXGKIURHkRsILoweysCpesjiTg4qDcL+yTibV
FP2wjVbniKESMKS6qL71tiT5sexvLsLwMNcGiHPj94qCIQuI7DLhLdBVsL5Su6gI
sbtgv0dsq4auRYAbQdMaH1hFvu6WptsuttIbOMnz2Yegi2z28H8uVXkbk2WVLbqG
ZESUwutGh8MzOL2RJ4jyyQq5sfo++CRGlfKjr6ImZRv03dv0pe/W85062cK5cKNs
cgDDJjGRorOXW7dyU6jG2gRqODOQBObIv3w5efdq5OgzOWlbI4EC+Y5u1Z0JF/76
pSwtGXA6YhwC+9LLAlnVTHG+yOwuLmAICgoKcTbzTVDKA2YQZG/cYuQfI5S1wD8e
X6urPx3Md2GCwLXQ9mzKBzKZUpu/Tuhx0NvwF4qVxy6x1PELjn68zuP7abDHr46r
57/09ooVN+iXXnEGMtQVS/OPvYHSa2NgTSZz6Y86lCRbZmUOOlK31RDNlMvYNA+s
3iIVHovno/JuJnTOE8LY
=fQ8z
-----END PGP SIGNATURE-----
Merge tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pul removal of obsolete architecture ports from Arnd Bergmann:
"This removes the entire architecture code for blackfin, cris, frv,
m32r, metag, mn10300, score, and tile, including the associated device
drivers.
I have been working with the (former) maintainers for each one to
ensure that my interpretation was right and the code is definitely
unused in mainline kernels. Many had fond memories of working on the
respective ports to start with and getting them included in upstream,
but also saw no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company in
charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It
seems that all the SoC product lines are still around, but have not
used the custom CPU architectures for several years at this point. In
contrast, CPU instruction sets that remain popular and have actively
maintained kernel ports tend to all be used across multiple licensees.
[ See the new nds32 port merged in the previous commit for the next
generation of "one company in charge of an SoC line, a CPU
microarchitecture and a software ecosystem" - Linus ]
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I
made sure that they are all unused. Some architectures (notably tile,
mn10300, and blackfin) are still being shipped in products with old
kernels, but those products will never be updated to newer kernel
releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing
their support or getting it added to mainline gcc in the first
place. They all have patched gcc-7.3 ports that work to some
degree, but complete upstream support won't happen before gcc-8.1.
Csky posted their first kernel patch set last week, their situation
will be similar
[ Palmer Dabbelt points out that RISC-V support is in mainline gcc
since gcc-7, although gcc-7.3.0 is the recommended minimum - Linus ]"
This really says it all:
2498 files changed, 95 insertions(+), 467668 deletions(-)
* tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (74 commits)
MAINTAINERS: UNICORE32: Change email account
staging: iio: remove iio-trig-bfin-timer driver
tty: hvc: remove tile driver
tty: remove bfin_jtag_comm and hvc_bfin_jtag drivers
serial: remove tile uart driver
serial: remove m32r_sio driver
serial: remove blackfin drivers
serial: remove cris/etrax uart drivers
usb: Remove Blackfin references in USB support
usb: isp1362: remove blackfin arch glue
usb: musb: remove blackfin port
usb: host: remove tilegx platform glue
pwm: remove pwm-bfin driver
i2c: remove bfin-twi driver
spi: remove blackfin related host drivers
watchdog: remove bfin_wdt driver
can: remove bfin_can driver
mmc: remove bfin_sdh driver
input: misc: remove blackfin rotary driver
input: keyboard: remove bf54x driver
...
clk_disable_unprepare() was added to one error path,
but there is another one. The patch makes sure clk is
disabled at the both of them.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The blackfin architecture is getting removed, so this driver has
become obsolete.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Aaron Wu <aaron.wu@analog.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A lot of Kconfig symbols have architecture specific dependencies.
In those cases that depend on architectures we have already removed,
they can be omitted.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Allow the device tree to specify a watchdog to fallover to
the alternate boot source.
The aspeeed watchdog can set a latch directing flash chip select 0 to
chip select 1, allowing boot from an alternate media if the watchdog
is not reset in time. On the ast2400 bank 1 also goes to flash bank 1,
while on the ast2500 the chip selects are swapped.
Also clear the secondary boot bit during the machine restart operation.
Otherwise, the system will switch to the alternate boot after every
reboot, which is not desired.
Signed-off-by: Milton Miller <miltonm@us.ibm.com>
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The Nuvoton NPCM750 has a watchdog implemented as a single register
inside the timer peripheral.
This driver exposes that watchdog as a standard watchdog device with
coarse timeout intervals, limited by the combination of prescaler and
counter that is provided by the hardware. The calculation is taken from
the Nuvoton vendor tree.
The watchdog is left running if a bootloader had it going. The rate is
the one specified in the device tree, or the default value (obtained
from the datasheet).
There is a pre-timeout IRQ that is wired up. This timeout always occurs
1024 clocks before the timeout.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The resource allocation in WDAT watchdog has off-one-by error, it sets
one byte more than the actual end address. This may eventually lead
to unexpected resource conflicts.
Fixes: 058dfc7670 (ACPI / watchdog: Add support for WDAT hardware watchdog)
Cc: 4.9+ <stable@vger.kernel.org> # 4.9+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlqlyPEeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGNa0H/RIa/StQuYu/SBwa
JRqQFmkIsx+gG+FyamJrqGzRfyjounES8PbfyaN3cCrzYgeRwMp1U/bZW6/l5tkb
OjTtrCJ6CJaa21fC/7aqn3rhejHciKyk83EinMu5WjDpsQcaF2xKr3SaPa62Ja24
fhawKq3CnUa+OUuAbicVX8yn4viUB6x8FjSN/IWfp3Cs4IBR7SGxxD7A4MET9FbQ
5OOu0al8ly9QeCggTtJyk+cApeLfexEBTbUur9gm7GcH9jhUtJSyZCZsDJx6M2yb
CwdgF4fyk58c1fuHvTFb0AdUns55ba3nicybRHHMVbDpZIG9v4/M1yJETHHf5cD7
t3rFjrY=
=+Ldf
-----END PGP SIGNATURE-----
Merge tag 'v4.16-rc5' into devel
Linux 4.16-rc5 merged into the GPIO devel branch to resolve
a nasty conflict between fixes and devel in the RCAR driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some platforms lose this state in suspend. It should be safe to do this
unconditionally.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
RK3399 has rst_pulse_length in CONTROL_REG[4:2], determining the length
of pulse to issue for system reset. We shouldn't clobber this value,
because that might make the system reset ineffective. On RK3399, we're
seeing that a value of 000b (meaning 2 cycles) yields an unreliable
(partial?) reset, and so we only fully reset after the watchdog fires a
second time. If we retain the system default (010b, or 8 clock cycles),
then the watchdog reset is much more reliable.
Read-modify-write retains the system value and improves reset
reliability.
It seems we were intentionally clobbering the response mode previously,
to ensure we performed a system reset (we don't support an interrupt
notification), so retain that explicitly.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
If clk_prepare_enable(wdt->rtc_enable) fails,
wdt->enable clock is left enabled.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Assert RESET_SYSTEM bit for any reset and set MODE field from reset
type.
The watchdog control register has a RESET_SYSTEM bit that is really
closer to activate a reset, and RESET_SYSTEM_MODE field that chooses
how much to reset.
Before this patch, a node without these optional property would do a
SOC reset, but a node with properties requesting a cpu or SOC reset
would do nothing and a node requesting a system reset would do a
SOC reset.
Fixes: b7f0b8ad25 ("drivers/watchdog: ASPEED reference dev tree properties for config")
Signed-off-by: Milton Miller <miltonm@us.ibm.com>
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On iWave's boards iwg20d and iwg22d the only way to reboot the system is
by means of the watchdog.
This patch adds a restart handler to rwdt_ops, and also makes sure we
keep its priority to the lowest level, in order to not override other
more effective handlers.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Due to commits:
* "ARM: shmobile: Add watchdog support",
* "ARM: shmobile: rcar-gen2: Add watchdog support", and
* "soc: renesas: rcar-rst: Enable watchdog as reset trigger for Gen2",
we now have everything we needed for the watchdog to work on Gen2 and
RZ/G1.
However, on early revisions of some R-Car Gen2 SoCs, and depending on SMP
configuration, the system may fail to restart on watchdog time-out, and
lock up instead.
Specifically:
- On R-Car H2 ES1.0 and M2-W ES1.0, watchdog restart fails unless
only the first CPU core is in use (using e.g. the "maxcpus=1" kernel
commandline option).
- On R-Car V2H ES1.1, watchdog restart fails unless SMP is disabled
completely (using CONFIG_SMP=n during build configuration, or using
the "nosmp" or "maxcpus=0" kernel commandline options).
This commit adds "renesas,rcar-gen2-wdt" as compatible string for R-Car
Gen2 and RZ/G1, but also prevents the system from using the watchdog
driver in cases where the system would fail to restart by blacklisting
the affected SoCs, using the minimum known working revisions (ES2.0 on R-Car
H2, and ES3.0 on M2-W), and taking the actual SMP software configuration
into account.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
[Geert: blacklisting logic]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On R-Car Gen2 and RZ/G1 the watchdog IP clock needs to be always ON,
on R-Car Gen3 we power the IP down during suspend.
This commit adds suspend/resume support, so that the watchdog counting
"pauses" during suspend on all of the SoCs compatible with this driver
and on those we are now adding support for (R-Car Gen2 and RZ/G1).
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
These patches remove the metag architecture and tightly dependent
drivers from the kernel. With the 4.16 kernel the ancient gcc 4.2.4
based metag toolchain we have been using is hitting compiler bugs, so
now seems a good time to drop it altogether.
-----BEGIN PGP SIGNATURE-----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=zDIl
-----END PGP SIGNATURE-----
Merge tag 'metag_remove_2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jhogan/metag into asm-generic
Remove metag architecture
These patches remove the metag architecture and tightly dependent
drivers from the kernel. With the 4.16 kernel the ancient gcc 4.2.4
based metag toolchain we have been using is hitting compiler bugs, so
now seems a good time to drop it altogether.
* tag 'metag_remove_2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
i2c: img-scb: Drop METAG dependency
media: img-ir: Drop METAG dependency
watchdog: imgpdc: Drop METAG dependency
MAINTAINERS/CREDITS: Drop METAG ARCHITECTURE
tty: Remove metag DA TTY and console driver
clocksource: Remove metag generic timer driver
irqchip: Remove metag irqchip drivers
Drop a bunch of metag references
docs: Remove remaining references to metag
docs: Remove metag docs
metag: Remove arch/metag/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Now that arch/metag/ has been removed, remove the METAG dependency from
the IMG IR device driver. The hardware is also present on MIPS SoCs so
the driver still has value.
Signed-off-by: James Hogan <jhogan@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-metag@vger.kernel.org
Update driver version number to reflect changes.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add a few dynamic debug messages to aid in module level debug.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Make whether or not the hpwdt watchdog delivers a pretimeout NMI
programable by the user.
The underlying iLO hardware is programmable as to whether or not
a pre-timeout NMI is delivered to the system before the iLO resets
the system. However, the iLO does not allow for programming the
length of time that NMI is delivered before the system is reset.
By watchdog API, in hpwdt_set_pretimeout a val == 0 disables the NMI.
When val != 0, hpwdt_set_pretimeout will enable the pretimeout NMI
provided the current timeout is greator than the HW specified
pretimeout length. Otherwise an error is returned.
In set_timeout, if the new timeout is <= an already established pretimeout,
the pretimeout is canceled. This matches the action watchdog_set_timeout
in the watchdog core would do if an hpwdt specific set_timeout
function wasn't specified.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The intent of this parameter is unclear and it sets up a
race between the reset of the system by ASR and crashdump.
The length of time between receipt of the pretimeout NMI
and the ASR reset of the system is fixed by hardware.
Turning the parameter off doesn't necessairly prevent a crash dump.
Also, having the ASR reset occur while the system is crash dumping
doesn't imply that the dump was hung given the short duration
between the NMI and the reset.
This parameter is not a substitute for having a architected watchdog
crashdump hang detection paridigm.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Modify prior change to not claim an NMI unless originated
from iLO to apply only to iLO5 and later going forward.
This restores hpwdt traditional behavior of calling panic
if the NMI is NMI_IO_CHECK, NMI_SERR, or NMI_UNKNOWN for
legacy hardware.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Include the nmistat in the nmi_panic message to give support
an indication why the NMI was called (e.g. a timeout or generate
nmi button.)
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
If devm_reset_control_get_exclusive() fails, asm9260_wdt_probe()
returns immediately. But clks has been already enabled at that point,
so it is required to disable them or to move the code around.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Licence text is specifying "GPLv2" but the MODULE_LICENSE is set to "GPLv2
or later".
See include/linux/module.h:
"GPL" [GNU Public License v2 or later]
"GPL v2" [GNU Public License v2]
When on it, add SPDX identifier tag.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog_init_timeout() will preserve wdd->timeout value if
no parameter nor timeout-secs dt property is set.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog_init_timeout() will preserve wdd->timeout value if
no parameter nor timeout-secs dt property is set.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog_init_timeout() will preserve wdd->timeout value if no parameter
nor timeout-secs dt property is set.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog_init_timeout() will allways pick timeout_param since it
defaults to a valid timeout.
Following best practice described in
Documentation/watchdog/watchdog-kernel-api.txt to make use of
the parameter logic.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog_init_timeout() will allways pick timeout_param since it
defaults to a valid timeout.
By following best practice described in
Documentation/watchdog/watchdog-kernel-api.txt, it also
let us to set timout-sec property in devicetree.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog_init_timeout() will allways pick timeout_param since it
defaults to a valid timeout.
By following best practice described in
Documentation/watchdog/watchdog-kernel-api.txt, it also
let us to set timout-sec property in devicetree.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog_init_timeout() will allways pick timeout_param since it
defaults to a valid timeout.
Following best practice described in
Documentation/watchdog/watchdog-kernel-api.txt to make use of
the parameter logic.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog_init_timeout() will allways pick timeout_param since it
defaults to a valid timeout.
By following best practice described in
Documentation/watchdog/watchdog-kernel-api.txt, it also
let us to set timout-sec property in devicetree.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog_init_timeout() will allways pick timeout_param since it
defaults to a valid timeout.
By following best practice described in
Documentation/watchdog/watchdog-kernel-api.txt, it also
let us to set timout-sec property in devicetree.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog_init_timeout() will allways pick timeout_param since it
defaults to a valid timeout.
Following best practice described in
Documentation/watchdog/watchdog-kernel-api.txt to make use of
the parameter logic.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
By following best practice described in
Documentation/watchdog/watchdog-kernel-api.txt, it also let us to set
timout-sec property in devicetree.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Gen8 and prior Proliant systems supported the "CRU" interface
to firmware. This interfaces allows linux to "call back" into firmware
to source the cause of an NMI. This feature isn't fully utilized
as the actual source of the NMI isn't printed, the driver only
indicates that the source couldn't be determined when the call
fails.
With the advent of Gen9, iCRU replaces the CRU. The call back
feature is no longer available in firmware. To be compatible and
not attempt to call back into firmware on system not supporting CRU,
the SMBIOS table is consulted to determine if it is safe to
make the call back or not.
This results in about half of the driver code being devoted
to either making CRU calls or determing if it is safe to make
CRU calls. As noted, the driver isn't really using the results of
the CRU calls.
Furthermore, as a consequence of the Spectre security issue, the
BIOS/EFI calls are being wrapped into Spectre-disabling section.
Removing the call back in hpwdt_pretimeout assists in this effort.
As the CRU sourcing of the NMI isn't required for handling the
NMI and there are security concerns with making the call back, remove
the legacy (pre Gen9) NMI sourcing and the DMI code to determine if
the system had the CRU interface.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
According to SBSA spec v3.1 section 5.3:
All registers are 32 bits in size and should be accessed using
32-bit reads and writes. If an access size other than 32 bits
is used then the results are IMPLEMENTATION DEFINED.
[...]
The Generic Watchdog is little-endian
The current code uses readq to read the watchdog compare register
which does a 64-bit access. This fails on ThunderX2 which does not
implement 64-bit access to this register.
Fix this by using lo_hi_readq() that does two 32-bit reads.
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Watchdog close is "expected" when any byte is 'V' not just the last one.
Writing "V" to the device fails because the last byte is the end of string.
$ echo V > /dev/watchdog
f71808e_wdt: Unexpected close, not stopping watchdog!
Signed-off-by: Igor Pylypiv <igor.pylypiv@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The ISA_BUS_API Kconfig option enables the compilation of the ISA bus
driver. The ISA bus driver does not perform any hardware interaction,
and is instead just a thin layer of software abstraction to eliminate
boilerplate code common to ISA-style device drivers. Since ISA_BUS_API
has no dependencies and does not jeopardize the integrity of the system
when enabled, drivers should select it when the ISA bus driver
functionality is needed.
Cc: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
isp5100_tco.c uses watchdog core functions (from watchdog_core.c) and, when
compiled without CONFIG_WATCHDOG_CORE being set, it produces the
following build error:
ERROR: "devm_watchdog_register_device" [drivers/watchdog/sp5100_tco.ko] undefined!
ERROR: "watchdog_init_timeout" [drivers/watchdog/sp5100_tco.ko] undefined!
Fix this by selecting CONFIG_WATCHDOG_CORE.
Fixes: 7cd9d5fff7 ("watchdog: sp5100_tco: Convert to use watchdog subsystem")
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
xen_wdt uses watchdog core functions (from watchdog_core.c) and, when
compiled without CONFIG_WATCHDOG_CORE being set, it produces the
following build error:
ERROR: "devm_watchdog_register_device" [drivers/watchdog/xen_wdt.ko] undefined!
ERROR: "watchdog_init_timeout" [drivers/watchdog/xen_wdt.ko] undefined!
Fix this by selecting CONFIG_WATCHDOG_CORE when CONFIG_XEN_WDT is set.
Fixes: 18cffd68e0 ("watchdog: xen_wdt: use the watchdog subsystem")
Signed-off-by: Radu Rendec <radu.rendec@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
i6300esb uses fuctions defined in watchdog_core.c, and when
CONFIG_WATCHDOG_CORE is not set we have this build error:
drivers/watchdog/i6300esb.o: In function `esb_remove':
i6300esb.c:(.text+0xcc): undefined reference to `watchdog_unregister_device'
drivers/watchdog/i6300esb.o: In function `esb_probe':
i6300esb.c:(.text+0x2a1): undefined reference to `watchdog_init_timeout'
i6300esb.c:(.text+0x388): undefined reference to `watchdog_register_device'
make: *** [Makefile:1029: vmlinux] Error 1
Fix this by selecting CONFIG_WATCHDOG_CORE when I6300ESB_WDT is set.
Fixes: 7af4ac8772 ("watchdog: i6300esb: use the watchdog subsystem")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
We can build this driver with or without NVMEM, but not built-in
when NVMEM is a loadable module:
drivers/watchdog/rave-sp-wdt.o: In function `rave_sp_wdt_probe':
rave-sp-wdt.c:(.text+0x27c): undefined reference to `nvmem_cell_get'
rave-sp-wdt.c:(.text+0x290): undefined reference to `nvmem_cell_read'
rave-sp-wdt.c:(.text+0x2c4): undefined reference to `nvmem_cell_put'
This adds a Kconfig dependency to enforce that.
Fixes: c3bb333457 ("watchdog: Add RAVE SP watchdog driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)
iEYEABECAAYFAlp4I7MACgkQ+iyteGJfRsp34QCgi3O78Sajso9iJNMj5KJsQTEt
VOsAn1ioW2jO9CmZQoj4IlVStlKU0NCN
=jeHv
-----END PGP SIGNATURE-----
Merge tag 'linux-watchdog-4.16-rc1' of git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- new watchdog device drivers for Realtek RTD1295 and Spreadtrum SC9860
platform
- add support for the following devices: jz4780 SoC, AST25xx series SoC
and r8a77970 SoC
- convert to watchdog framework: i6300esb_wdt, xen_wdt and sp5100_tco
- several fixes for watchdog core
- remove at32ap700x and obsolete documentation
- gpio: Convert to use GPIO descriptors
- rename gemini into FTWDT010 as this IP block is generc from Faraday
Technology
- various clean-ups and small bugfixes
- add Guenter Roeck as co-maintainer
- change maintainers e-mail address
* tag 'linux-watchdog-4.16-rc1' of git://www.linux-watchdog.org/linux-watchdog: (74 commits)
documentation: watchdog: remove documentation of w83697hf_wdt/w83697ug_wdt
documentation: watchdog: remove documentation for ixp2000
documentation: watchdog: remove documentation of at32ap700x_wdt
watchdog: remove at32ap700x_wdt
watchdog: sp5100_tco: Add support for recent FCH versions
watchdog: sp5100-tco: Abort if watchdog is disabled by hardware
watchdog: sp5100_tco: Use bit operations
watchdog: sp5100_tco: Convert to use watchdog subsystem
watchdog: sp5100_tco: Clean up function and variable names
watchdog: sp5100_tco: Use dev_ print functions where possible
watchdog: sp5100_tco: Match PCI device early
watchdog: sp5100_tco: Clean up sp5100_tco_setupdevice
watchdog: sp5100_tco: Use standard error codes
watchdog: sp5100_tco: Use request_muxed_region where possible
watchdog: sp5100_tco: Fix watchdog disable bit
watchdog: sp5100_tco: Always use SP5100_IO_PM_{INDEX_REG,DATA_REG}
watchdog: core: make sure the watchdog_worker is not deferred
watchdog: mt7621: switch to using managed devm_watchdog_register_device()
watchdog: mt7621: set WDOG_HW_RUNNING bit when appropriate
watchdog: imx2_wdt: restore previous timeout after suspend+resume
...
Starting with Family 16h Models 30h-3Fh and Family 15h Models 60h-6Fh,
watchdog address space decoding has changed. The cutover point is already
identified in the i2c-piix2 driver, so use the same mechanism.
Cc: Zoltán Böszörményi <zboszor@pr.hu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
If the watchdog control register indicates that the watchdog hardware
is disabled even after we tried to enable it, there is no point to
instantiate the driver.
Cc: Zoltán Böszörményi <zboszor@pr.hu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Using bit operations makes it easier to improve the driver.
Cc: Zoltán Böszörményi <zboszor@pr.hu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Convert to watchdog subsystem. As part of that rework, use devm functions
where possible, and replace almost all static variables with a dynamically
allocated data structure.
Cc: Zoltán Böszörményi <zboszor@pr.hu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use more common function and variable names.
Use pdev instead of dev for platform device.
Use sp5100_tco_probe() instead of sp5100_tco_init() for the probe function.
Drop sp5100_tco_cleanup(); just move the code into sp5100_tco_remove().
Use sp5100_tco_init() instead of sp5100_tco_init_module() for the module
initialization function.
Use sp5100_tco_exit() instead of sp5100_tco_cleanup_module() for the module
exit function.
Use consistent defines for accessing the watchdog control register.
Cc: Zoltán Böszörményi <zboszor@pr.hu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use dev_ instead of pr_ functions where possible.
Cc: Zoltán Böszörményi <zboszor@pr.hu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Match PCI device in module init function, not in the probe function.
It is pointless trying to probe if we can determine early that the device
is not supported.
Cc: Zoltán Böszörményi <zboszor@pr.hu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
There are too many unnecessary goto statements in sp5100_tco_setupdevice().
Rearrange the code and limit goto statements to error handling.
Cc: Zoltán Böszörményi <zboszor@pr.hu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
By using standard error codes, we can identify and return more than one
error condition.
Cc: Zoltán Böszörményi <zboszor@pr.hu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use request_muxed_region for multiplexed IO memory regions.
Also, SP5100_IO_PM_INDEX_REG/SP5100_IO_PM_DATA_REG are only
used during initialization; it is unnecessary to keep the
address range reserved.
Cc: Zoltán Böszörményi <zboszor@pr.hu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
According to all published information, the watchdog disable bit for SB800
compatible controllers is bit 1 of PM register 0x48, not bit 2. For the
most part that doesn't matter in practice, since the bit has to be cleared
to enable watchdog address decoding, which is the default setting, but it
still needs to be fixed.
Cc: Zoltán Böszörményi <zboszor@pr.hu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
SP5100_IO_PM_INDEX_REG and SB800_IO_PM_INDEX_REG are used inconsistently
and define the same value. Just use SP5100_IO_PM_INDEX_REG throughout.
Do the same for SP5100_IO_PM_DATA_REG and SB800_IO_PM_DATA_REG.
Use helper functions to access the indexed registers.
Cc: Zoltán Böszörményi <zboszor@pr.hu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
commit 4cd13c21b2 ("softirq: Let ksoftirqd do its job") has the
effect of deferring timer handling in case of high CPU load, hence
delaying the delayed work allthought the worker is running which
high realtime priority.
As hrtimers are not managed by softirqs, this patch replaces the
delayed work by a plain work and uses an hrtimer to schedule that work.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Guenter Roeck <Linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This does the necessary cleanup on driver unload automatically.
Signed-off-by: André Draszik <git@andred.net>
Cc: linux-watchdog@vger.kernel.org
Cc: John Crispin <john@phrozen.org>
Reviewed-by: Guenter Roeck <Linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
If the watchdog hardware is enabled/running during boot, e.g.
due to a boot loader configuring it, we must tell the
watchdog framework about this fact so that it can ping the
watchdog until userspace opens the device and takes over
control.
Do so using the WDOG_HW_RUNNING flag that exists for exactly
that use-case.
Given the watchdog driver core doesn't know what timeout was
originally set by whoever started the watchdog (boot loader),
we make sure to update the timeout in the hardware according
to what the watchdog core thinks it is.
Signed-off-by: André Draszik <git@andred.net>
Cc: linux-watchdog@vger.kernel.org
Cc: John Crispin <john@phrozen.org>
Reviewed-by: Guenter Roeck <Linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
When the watchdog device is suspended, its timeout is set to the maximum
value. During resume, the previously set timeout should be restored.
This does not work at the moment.
The suspend function calls
imx2_wdt_set_timeout(wdog, IMX2_WDT_MAX_TIME);
and resume reverts this by calling
imx2_wdt_set_timeout(wdog, wdog->timeout);
However, imx2_wdt_set_timeout() updates wdog->timeout. Therefore,
wdog->timeout is set to IMX2_WDT_MAX_TIME when we enter the resume
function.
Fix this by adding a new function __imx2_wdt_set_timeout() which
only updates the hardware settings. imx2_wdt_set_timeout() now calls
__imx2_wdt_set_timeout() and then saves the new timeout to
wdog->timeout.
During suspend, we call __imx2_wdt_set_timeout() directly so that
wdog->timeout won't be updated and we can restore the previous value
during resume. This approach makes wdog->timeout different from the
actual setting in the hardware which is usually not a good thing.
However, the two differ only while we're suspended and no kernel code is
running, so it should be ok in this case.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Cc: stable@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
When running a command like 'chrt -f 50 dd if=/dev/zero of=/dev/null',
the watchdog_worker fails to service the HW watchdog and the
HW watchdog fires long before the watchdog soft timeout.
At the moment, the watchdog_worker is invoked as a delayed work.
Delayed works are handled by non realtime kernel threads. The
WQ_HIGHPRI flag only increases the niceness of that threads.
This patch replaces the delayed work logic by kthread delayed work,
and sets the associated kernel task to SCHED_FIFO with the highest
priority, in order to ensure that the watchdog worker will run as
soon as possible.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This adds a restart function to the davinci watchdog timer driver.
This is copied from arch/arm/mach-davinci/time.c and will allow us to
remove the code from there.
Signed-off-by: David Lechner <david@lechnology.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
All parameters of watchdog_init_timeout() are documented with exception
of wdd, thus generating a build warning.
This patch document it and so remove the following build warning:
drivers/watchdog/watchdog_core.c:113: warning: No description found for parameter 'wdd'
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The new hpwdt_my_nmi() function is used conditionally, which produces
a harmless warning in some configurations:
drivers/watchdog/hpwdt.c:478:12: error: 'hpwdt_my_nmi' defined but not used [-Werror=unused-function]
This moves it inside of the #ifdef that protects its caller, to silence
the warning.
Fixes: 621174a92851 ("watchdog: hpwdt: Check source of NMI")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case I replaced "Fall" with a proper
"fall through" comment, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case I replaced "Fall" with a proper
"fall through" comment, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
There is no need to #define the license of the driver, just put it in
the MODULE_LICENSE() line directly as a text string.
This allows tools that check that the module license matches the source
code license to work properly, as there is no need to unwind the
unneeded dereference, especially when it is defined just a few lines
above from where it is used.
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Guenter Roeck <linux@roeck-us.net>
Reported-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The initial info message (early in the xen_wdt_init_module() function)
is not very useful and we already have a message on successful probe. If
the probe fails, additional messages are printed anyway.
The version number serves no useful purpose and it ran out of favor
upstream anyway.
Signed-off-by: Radu Rendec <rrendec@arista.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Change the xen_wdt driver to use the watchdog subsystem instead of
registering and manipulating the char device directly through the misc
API. This is mainly getting rid of the "write" and "ioctl" methods and
part of the watchdog control logic (which are all implemented by the
watchdog subsystem).
Even though the watchdog subsystem supports registering and handling
multiple watchdog devices at the same time, the xen_wdt driver has an
inherent limitation of only one device due to the way the Xen hypervisor
exposes watchdog functionality. However, the driver can now coexist with
other watchdog devices (supported by different drivers).
Signed-off-by: Radu Rendec <rrendec@arista.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds the watchdog driver for Spreadtrum SC9860 platform.
Signed-off-by: Eric Long <eric.long@spreadtrum.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The watchdog core includes a worker function which pings the
watchdog until user app starts pinging it and which also
pings it if the HW require more frequent pings.
Use that function instead of the dedicated timer.
In the mean time, we can allow the user to change the timeout.
Then change the timeout module parameter to use seconds and
use the watchdog_init_timeout() core function.
On some HW (eg: the 8xx), SWCRR contains bits unrelated to the
watchdog which have to be preserved upon write.
This driver has nothing preventing the use of the magic close, so
enable it.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The first patch above (https://patchwork.kernel.org/patch/9970181/)
makes the oops go away, but it just papers over the problem. The real
problem is that the watchdog core clears WDOG_HW_RUNNING in
watchdog_stop, and the gpio driver fails to set it in its stop
function when it doesn't actually stop it. This means that the core
doesn't know that it now has responsibility for petting the device, in
turn causing the device to reset the system (I hadn't noticed this
because the board I'm working on has that reset logic disabled).
How about this (other drivers may of course have the same problem, I
haven't checked). One might say that ->stop should return an error
when the device can't be stopped, but OTOH this brings parity between
a device without a ->stop method and a GPIO wd that has always-running
set. IOW, I think ->stop should only return an error when an actual
attempt to stop the hardware failed.
From: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
The watchdog framework clears WDOG_HW_RUNNING before calling
->stop. If the driver is unable to stop the device, it is supposed to
set that bit again so that the watchdog core takes care of sending
heart-beats while the device is not open from user-space. Update the
gpio_wdt driver to honour that contract (and get rid of the redundant
clearing of WDOG_HW_RUNNING).
Fixes: 3c10bbde10 ("watchdog: core: Clear WDOG_HW_RUNNING before calling the stop function")
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case I replaced "Fall" with a proper
"fall through" comment, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case I replaced "Fall" with a proper
"fall through" comment, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case I replaced "Fall" with a proper
"fall through" comment, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case I replaced "Fall" with a proper
"fall through" comment, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case I replaced "Fall" with a proper
"fall through" comment, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case I replaced "Fall" with a proper
"fall through" comment, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case I replaced "Fall" with a proper
"fall through" comment, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The initial info message (early in the esb_probe() function) is not very
useful and we already have a message on successful probe, which includes
device identification. If the probe fails (e.g. PCI related errors),
additional messages are printed anyway.
The version number was only used in the initial info message. Other than
that, it serves no useful purpose and it ran out of favor upstream
anyway.
Signed-off-by: Radu Rendec <rrendec@arista.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The minimum, maximum and default values for the watchdog heartbeat
(timeout) were hardcoded in several places (including module parameter
description and warning message for invalid module parameter value).
This patch adds macros for the aforementioned values and replaces all
occurences of hardcoded values by these macros.
Signed-off-by: Radu Rendec <rrendec@arista.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Support multiple i6300esb devices simultaneously, by removing the single
device restriction in the original design and leveraging the multiple
device support of the watchdog subsystem.
This patch replaces the global definitions of watchdog device data with
a dynamically allocated structure. This structure is allocated during
device probe, so multiple independent structures can be allocated if
multiple devices are probed.
Signed-off-by: Radu Rendec <rrendec@arista.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Change the i6300esb driver to use the watchdog subsystem instead of the
legacy watchdog API. This is mainly just getting rid of the "write" and
"ioctl" methods and part of the watchdog control logic (which are all
implemented by the watchdog subsystem).
Even though the watchdog subsystem supports registering and handling
multiple watchdog devices at the same time, the i6300esb driver still
has a limitation of only one i6300esb device due to some global variable
usage that comes from the original design. However, the driver can now
coexist with other watchdog devices (supported by different drivers).
Signed-off-by: Radu Rendec <rrendec@arista.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Do not claim the NMI (i.e. return NMI_DONE) if the source of
the NMI isn't the iLO watchdog or debug.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The usage of of_device_get_match_data reduce the code size a bit.
Furthermore, it prevents an improbable dereference when
of_match_device() return NULL.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The Xen watchdog driver uses __kernel_time_t and ktime_to_timespec()
internally for managing its timeouts. Both are deprecated because of
y2038 problems. The driver itself is fine, since it only uses monotonic
times, but converting it to use ktime_get_seconds() avoids the deprecated
interfaces and is slightly simpler.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch removes the windows protection routine that got
now covered by the wdt core.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The DA9062 watchdog occasionally enters error condition and resets the
system if the timeout is changed quickly after the timer was enabled.
The method of disabling and waiting for > 150 µs before setting the
new timeout is taken from the DA9052 driver.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Register a restart handler for the da9062 watchdog. System restart is
triggered by sending the shutdown command to the PMIC.
As more-suitable restart handlers may exist, the priority of the
watchdog restart handler is set to 128.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The Moxart does not appear to be using the interrupt from the
watchdog timer, maybe it's not even routed, so as to support
more architectures with this driver, make the interrupt
optional.
While we are at it: actually enable the use of the interrupt
if present by setting the right bit in the control register
and define the missing control register bits.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This renames all the driver files and symbols for the Gemini
watchdog to FTWDT010 as it has been revealed that this IP block
is a generic watchdog timer from Faraday Technology used in
several SoC designs.
Select this driver by default for the Gemini, it is a sensible
driver to always have enabled.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This converts the GPIO watchdog driver to use GPIO descriptors
instead of relying on the old method to read out GPIO numbers
from the device tree and then using those with the old GPIO
API.
The descriptor API keeps track of whether the line is active
low so we can remove all active low handling and rely on the
GPIO descriptor to deal with this for us.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This add "dev" and "np" variables to make the probe() function
a bit easier to read.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The only way of stopping the watchdog is by resetting it.
Add the watchdog op for stopping the device and reset if
a reset line is provided.
At same time WDOG_HW_RUNNING should be remove from dw_wdt_start.
As commented by Guenter Roeck:
dw_wdt sets WDOG_HW_RUNNING in its open function. Result is
that the kref_get() in watchdog_open() won't be executed. But then
kref_put() in close will be called since the watchdog now does stop.
This causes the imbalance.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-watchdog@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Probing at device_initcall time lead to perverse cases where the
watchdog was probed after, say, I2C devices, which then leaves a
potentially running watchdog at the mercy of I2C device behaviour and
bus conditions.
Load the watchdog driver early to ensure that the kernel is patting it
well before initialising peripherals.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The driver also supports the watchdog in the AST25xx series, and
may work on earlier SoCs as well.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Apseed sounds like a good name for a web/mobile start-up incubator, but
isn't a reflection of Aspeed themselves.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
An unintended post-condition of probe() is that the watchdog is
disabled. This behaviour was introduced by an unnecessary write to the
control register to configure the hardware based on the devicetree. The
write is unnecessary because the cached control value that is
manipulated by the code parsing the devicetree is eventually written by
aspeed_wdt_enable(), which is when we care how the control register
should be configured.
Remove the write to restore expected behaviour.
Fixes: b7f0b8ad25 ("drivers/watchdog: ASPEED reference dev tree properties for config")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The watchdog unit present in the JZ4780 works the same as the one in the
JZ4740.
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add a watchdog driver for the Realtek RTD1295 SoC.
Based on QNAP's arch/arm/mach-rtk119x/driver/rtk_watchdog.c code and
mach-rtk119x/driver/dc2vo/fpga/include/iso_reg.h register defines.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This corrects:
commit cce78da766 ("watchdog: hpwdt: Add check for UEFI bits")
The test on HPE SMBIOS extension type 219 record "Misc Features"
bits for UEFI support is incorrect. The definition of the Misc Features
bits in the HPE SMBIOS OEM Extensions specification (and related
firmware) was changed to use a different pair of bits to
represent UEFI supported. Howerver, a corresponding change
to Linux was missed.
Current code/platform work because the iCRU test is working.
But purpose of cce78da766 is to ensure correct functionality
on future systems where iCRU isn't supported.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Commit da2a68b3eb ("watchdog: Enable COMPILE_TEST where possible")
enabled building the Indy watchdog driver when COMPILE_TEST is enabled.
However, the driver makes reference to symbols that are only defined for
certain platforms are selected in the config. These platforms select
SGI_HAS_INDYDOG. Without this, link time errors result, for example
when building a MIPS allyesconfig.
drivers/watchdog/indydog.o: In function `indydog_write':
indydog.c:(.text+0x18): undefined reference to `sgimc'
indydog.c:(.text+0x1c): undefined reference to `sgimc'
drivers/watchdog/indydog.o: In function `indydog_start':
indydog.c:(.text+0x54): undefined reference to `sgimc'
indydog.c:(.text+0x58): undefined reference to `sgimc'
drivers/watchdog/indydog.o: In function `indydog_stop':
indydog.c:(.text+0xa4): undefined reference to `sgimc'
drivers/watchdog/indydog.o:indydog.c:(.text+0xa8): more undefined
references to `sgimc' follow
make: *** [Makefile:1005: vmlinux] Error 1
Fix this by ensuring that CONFIG_INDIDOG can only be selected when the
necessary dependent platform symbols are built in.
Fixes: da2a68b3eb ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: <stable@vger.kernel.org> # 4.11 +
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Suggested-by: James Hogan <james.hogan@mips.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
If handle_boot_enabled is set to 0, the watchdog driver module use
counter will not be increased and kref_get() will not be called when
registering the watchdog. Subsequently, on open, this does not happen
either because the code believes that it was already done because the
hardware watchdog is marked as running.
We could introduce a state variable to indicate this state, but let's
just increase the module use counter and call kref_get() unconditionally
if the hardware watchdog is running when a driver is registering itself
to keep the code simple.
Fixes: 2501b01531 ("watchdog: core: add option to avoid early ...")
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
If a watchdog driver's open function sets WDOG_HW_RUNNING with the
expectation that the watchdog can not be stopped, but then stops the
watchdog anyway in its stop function, kref_get() wil not be called in
watchdog_open(). If the watchdog then stops on close, WDOG_HW_RUNNING
will be cleared and kref_put() will be called, causing a kref imbalance.
As result the character device data structure will be released, which in
turn will cause the system to crash on the next call to watchdog_open().
Fixes: ee142889e3 ("watchdog: Introduce WDOG_HW_RUNNING flag")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This changes all DEFINE_TIMER() callbacks to use a struct timer_list
pointer instead of unsigned long. Since the data argument has already been
removed, none of these callbacks are using their argument currently, so
this renames the argument to "unused".
Done using the following semantic patch:
@match_define_timer@
declarer name DEFINE_TIMER;
identifier _timer, _callback;
@@
DEFINE_TIMER(_timer, _callback);
@change_callback depends on match_define_timer@
identifier match_define_timer._callback;
type _origtype;
identifier _origarg;
@@
void
-_callback(_origtype _origarg)
+_callback(struct timer_list *unused)
{ ... }
Signed-off-by: Kees Cook <keescook@chromium.org>
Save a bit of cleanup code by leveraging newly added
devm_register_reboot_notifier().
[akpm@linux-foundation.org: small cleanup: avoid 80-col tricks]
Link: http://lkml.kernel.org/r/20170411160615.9784-1-andrew.smirnov@gmail.com
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These are the main MIPS changes for 4.15.
Fixes:
- ralink: Fix MT7620 PCI build issues (4.5)
- Disable cmpxchg64() and HAVE_VIRT_CPU_ACCOUNTING_GEN for 32-bit SMP
(4.1)
- Fix MIPS64 FP save/restore on 32-bit kernels (4.0)
- ptrace: Pick up ptrace/seccomp changed syscall numbers (3.19)
- ralink: Fix MT7628 pinmux (3.19)
- BCM47XX: Fix LED inversion on WRT54GSv1 (3.17)
- Fix n32 core dumping as o32 since regset support (3.13)
- ralink: Drop obsolete USB_ARCH_HAS_HCD select
Build system:
- Default to "generic" (multiplatform) system type instead of IP22
- Use generic little endian MIPS32 r2 configuration as default defconfig
instead of ip22_defconfig
FPU emulation:
- Fix exception generation for certain R6 FPU instructions
SMP:
- Allow __cpu_number_map to be larger than NR_CPUS for sparse CPU id
spaces
Miscellaneous:
- Add iomem resource for kernel bss section for kexec/kdump
- Atomics: Nudge writes on bit unlock
- DT files: Standardise "ok" -> "okay"
Platform support:
BMIPS:
- Enable HARDIRQS_SW_RESEND
Broadcom BCM63XX:
- Add clkdev lookup support
- Update clk driver, UART driver, DTs to handle named refclk from DTs
- Split apart various clocks to more closely match hardware
- Add ethernet clocks
Cavium Octeon:
- Remove usage of cvmx_wait() in favour of __delay()
ImgTec Pistachio:
- DT: Drop deprecated dwmmc num-slots property
Ingenic JZ4780:
- Add NFS root to Ci20 defconfig
- Add watchdog to Ci20 DT & defconfig, and allow building of watchdog
driver with this SoC
Generic (multiplatform):
- Migrate xilfpga (MIPSfpga) platform to the generic platform
Lantiq xway:
- Fix ASC0/ASC1 clocks
Minor cleanups:
- Define virt_to_pfn()
- Make thread_saved_pc static
- Simplify 32-bit sign extension in __read_64bit_c0_split()
- DMA: Use vma_pages() helper
- FPU emulation: Replace unsigned with unsigned int
- MM: Removed unused lastpfn
- Alchemy: Make clk_ops const
- Lasat: Use setup_timer() helper
- ralink: Use BIT() in MT7620 PCI driver
-----BEGIN PGP SIGNATURE-----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=xbL0
-----END PGP SIGNATURE-----
Merge tag 'mips_4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips
Pull MIPS updates from James Hogan:
"These are the main MIPS changes for 4.15.
Fixes:
- ralink: Fix MT7620 PCI build issues (4.5)
- Disable cmpxchg64() and HAVE_VIRT_CPU_ACCOUNTING_GEN for 32-bit SMP
(4.1)
- Fix MIPS64 FP save/restore on 32-bit kernels (4.0)
- ptrace: Pick up ptrace/seccomp changed syscall numbers (3.19)
- ralink: Fix MT7628 pinmux (3.19)
- BCM47XX: Fix LED inversion on WRT54GSv1 (3.17)
- Fix n32 core dumping as o32 since regset support (3.13)
- ralink: Drop obsolete USB_ARCH_HAS_HCD select
Build system:
- Default to "generic" (multiplatform) system type instead of IP22
- Use generic little endian MIPS32 r2 configuration as default
defconfig instead of ip22_defconfig
FPU emulation:
- Fix exception generation for certain R6 FPU instructions
SMP:
- Allow __cpu_number_map to be larger than NR_CPUS for sparse CPU id
spaces
Miscellaneous:
- Add iomem resource for kernel bss section for kexec/kdump
- Atomics: Nudge writes on bit unlock
- DT files: Standardise "ok" -> "okay"
Minor cleanups:
- Define virt_to_pfn()
- Make thread_saved_pc static
- Simplify 32-bit sign extension in __read_64bit_c0_split()
- DMA: Use vma_pages() helper
- FPU emulation: Replace unsigned with unsigned int
- MM: Removed unused lastpfn
- Alchemy: Make clk_ops const
- Lasat: Use setup_timer() helper
- ralink: Use BIT() in MT7620 PCI driver
Platform support:
BMIPS:
- Enable HARDIRQS_SW_RESEND
Broadcom BCM63XX:
- Add clkdev lookup support
- Update clk driver, UART driver, DTs to handle named refclk from DTs
- Split apart various clocks to more closely match hardware
- Add ethernet clocks
Cavium Octeon:
- Remove usage of cvmx_wait() in favour of __delay()
ImgTec Pistachio:
- DT: Drop deprecated dwmmc num-slots property
Ingenic JZ4780:
- Add NFS root to Ci20 defconfig
- Add watchdog to Ci20 DT & defconfig, and allow building of watchdog
driver with this SoC
Generic (multiplatform):
- Migrate xilfpga (MIPSfpga) platform to the generic platform
Lantiq xway:
- Fix ASC0/ASC1 clocks"
* tag 'mips_4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips: (46 commits)
MIPS: Add iomem resource for kernel bss section.
MIPS: cmpxchg64() and HAVE_VIRT_CPU_ACCOUNTING_GEN don't work for 32-bit SMP
MIPS: BMIPS: Enable HARDIRQS_SW_RESEND
MIPS: pci: Make use of the BIT() macro inside the mt7620 driver
MIPS: pci: Remove KERN_WARN instance inside the mt7620 driver
MIPS: pci: Remove duplicate define in mt7620 driver
MIPS: ralink: Fix typo in mt7628 pinmux function
MIPS: ralink: Fix MT7628 pinmux
MIPS: Fix odd fp register warnings with MIPS64r2
watchdog: jz4780: Allow selection of jz4740-wdt driver
MIPS/ptrace: Update syscall nr on register changes
MIPS/ptrace: Pick up ptrace/seccomp changed syscalls
MIPS: Fix an n32 core file generation regset support regression
MIPS: Fix MIPS64 FP save/restore on 32-bit kernels
MIPS: page.h: Define virt_to_pfn()
MIPS: Xilfpga: Switch to using generic defconfigs
MIPS: generic: Add support for MIPSfpga
MIPS: Set defconfig target to a generic system for 32r2el
MIPS: Kconfig: Set default MIPS system type as generic
MIPS: DTS: Remove num-slots from Pistachio SoC
...
Pull timer updates from Thomas Gleixner:
"Yet another big pile of changes:
- More year 2038 work from Arnd slowly reaching the point where we
need to think about the syscalls themself.
- A new timer function which allows to conditionally (re)arm a timer
only when it's either not running or the new expiry time is sooner
than the armed expiry time. This allows to use a single timer for
multiple timeout requirements w/o caring about the first expiry
time at the call site.
- A new NMI safe accessor to clock real time for the printk timestamp
work. Can be used by tracing, perf as well if required.
- A large number of timer setup conversions from Kees which got
collected here because either maintainers requested so or they
simply got ignored. As Kees pointed out already there are a few
trivial merge conflicts and some redundant commits which was
unavoidable due to the size of this conversion effort.
- Avoid a redundant iteration in the timer wheel softirq processing.
- Provide a mechanism to treat RTC implementations depending on their
hardware properties, i.e. don't inflict the write at the 0.5
seconds boundary which originates from the PC CMOS RTC to all RTCs.
No functional change as drivers need to be updated separately.
- The usual small updates to core code clocksource drivers. Nothing
really exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
timers: Add a function to start/reduce a timer
pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday()
timer: Prepare to change all DEFINE_TIMER() callbacks
netfilter: ipvs: Convert timers to use timer_setup()
scsi: qla2xxx: Convert timers to use timer_setup()
block/aoe: discover_timer: Convert timers to use timer_setup()
ide: Convert timers to use timer_setup()
drbd: Convert timers to use timer_setup()
mailbox: Convert timers to use timer_setup()
crypto: Convert timers to use timer_setup()
drivers/pcmcia: omap1: Fix error in automated timer conversion
ARM: footbridge: Fix typo in timer conversion
drivers/sgi-xp: Convert timers to use timer_setup()
drivers/pcmcia: Convert timers to use timer_setup()
drivers/memstick: Convert timers to use timer_setup()
drivers/macintosh: Convert timers to use timer_setup()
hwrng/xgene-rng: Convert timers to use timer_setup()
auxdisplay: Convert timers to use timer_setup()
sparc/led: Convert timers to use timer_setup()
mips: ip22/32: Convert timers to use timer_setup()
...
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. Switches to using the global that is
used everywhere else.
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The expire and data arguments of DEFINE_TIMER are only used in two places
and are ignored by the code (malta-display.c only uses mod_timer(),
never add_timer(), so the preset expires value is ignored). Set both
sets of arguments to zero.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Guenter Roeck <linux@roeck-us.net> # for watchdog parts
Cc: linux-mips@linux-mips.org
Cc: Petr Mladek <pmladek@suse.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: linux1394-devel@lists.sourceforge.net
Cc: linux-s390@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: linux-scsi@vger.kernel.org
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Ursula Braun <ubraun@linux.vnet.ibm.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Harish Patil <harish.patil@cavium.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Manish Chopra <manish.chopra@cavium.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-pm@vger.kernel.org
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Mark Gross <mark.gross@intel.com>
Cc: linux-watchdog@vger.kernel.org
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Michael Reed <mdr@sgi.com>
Cc: netdev@vger.kernel.org
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Link: https://lkml.kernel.org/r/1507159627-127660-10-git-send-email-keescook@chromium.org
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.14 for MIPS; below a summary of
the non-merge commits:
CM:
- Rename mips_cm_base to mips_gcr_base
- Specify register size when generating accessors
- Use BIT/GENMASK for register fields, order & drop shifts
- Add cluster & block args to mips_cm_lock_other()
CPC:
- Use common CPS accessor generation macros
- Use BIT/GENMASK for register fields, order & drop shifts
- Introduce register modify (set/clear/change) accessors
- Use change_*, set_* & clear_* where appropriate
- Add CM/CPC 3.5 register definitions
- Use GlobalNumber macros rather than magic numbers
- Have asm/mips-cps.h include CM & CPC headers
- Cluster support for topology functions
- Detect CPUs in secondary clusters
CPS:
- Read GIC_VL_IDENT directly, not via irqchip driver
DMA:
- Consolidate coherent and non-coherent dma_alloc code
- Don't use dma_cache_sync to implement fd_cacheflush
FPU emulation / FP assist code:
- Another series of 14 commits fixing corner cases such as NaN
propgagation and other special input values.
- Zero bits 32-63 of the result for a CLASS.D instruction.
- Enhanced statics via debugfs
- Do not use bools for arithmetic. GCC 7.1 moans about this.
- Correct user fault_addr type
Generic MIPS:
- Enhancement of stack backtraces
- Cleanup from non-existing options
- Handle non word sized instructions when examining frame
- Fix detection and decoding of ADDIUSP instruction
- Fix decoding of SWSP16 instruction
- Refactor handling of stack pointer in get_frame_info
- Remove unreachable code from force_fcr31_sig()
- Convert to using %pOF instead of full_name
- Remove the R6000 support.
- Move FP code from *_switch.S to *_fpu.S
- Remove unused ST_OFF from r2300_switch.S
- Allow platform to specify multiple its.S files
- Add #includes to various files to ensure code builds reliable and
without warning..
- Remove __invalidate_kernel_vmap_range
- Remove plat_timer_setup
- Declare various variables & functions static
- Abstract CPU core & VP(E) ID access through accessor functions
- Store core & VP IDs in GlobalNumber-style variable
- Unify checks for sibling CPUs
- Add CPU cluster number accessors
- Prevent direct use of generic_defconfig
- Make CONFIG_MIPS_MT_SMP default y
- Add __ioread64_copy
- Remove unnecessary inclusions of linux/irqchip/mips-gic.h
GIC:
- Introduce asm/mips-gic.h with accessor functions
- Use new GIC accessor functions in mips-gic-timer
- Remove counter access functions from irq-mips-gic.c
- Remove gic_read_local_vp_id() from irq-mips-gic.c
- Simplify shared interrupt pending/mask reads in irq-mips-gic.c
- Simplify gic_local_irq_domain_map() in irq-mips-gic.c
- Drop gic_(re)set_mask() functions in irq-mips-gic.c
- Remove gic_set_polarity(), gic_set_trigger(), gic_set_dual_edge(),
gic_map_to_pin() and gic_map_to_vpe() from irq-mips-gic.c.
- Convert remaining shared reg access, local int mask access and
remaining local reg access to new accessors
- Move GIC_LOCAL_INT_* to asm/mips-gic.h
- Remove GIC_CPU_INT* macros from irq-mips-gic.c
- Move various definitions to the driver
- Remove gic_get_usm_range()
- Remove __gic_irq_dispatch() forward declaration
- Remove gic_init()
- Use mips_gic_present() in place of gic_present and remove
gic_present
- Move gic_get_c0_*_int() to asm/mips-gic.h
- Remove linux/irqchip/mips-gic.h
- Inline __gic_init()
- Inline gic_basic_init()
- Make pcpu_masks a per-cpu variable
- Use pcpu_masks to avoid reading GIC_SH_MASK*
- Clean up mti, reserved-cpu-vectors handling
- Use cpumask_first_and() in gic_set_affinity()
- Let the core set struct irq_common_data affinity
microMIPS:
- Fix microMIPS stack unwinding on big endian systems
MIPS-GIC:
- SYNC after enabling GIC region
NUMA:
- Remove the unused parent_node() macro
R6:
- Constify r2_decoder_tables
- Add accessor & bit definitions for GlobalNumber
SMP:
- Constify smp ops
- Allow boot_secondary SMP op to return errors
VDSO:
- Drop gic_get_usm_range() usage
- Avoid use of linux/irqchip/mips-gic.h
Platform changes:
Alchemy:
- Add devboard machine type to cpuinfo
- update cpu feature overrides
- Threaded carddetect irqs for devboards
AR7:
- allow NULL clock for clk_get_rate
BCM63xx:
- Fix ENETDMA_6345_MAXBURST_REG offset
- Allow NULL clock for clk_get_rate
CI20:
- Enable GPIO and RTC drivers in defconfig
- Add ethernet and fixed-regulator nodes to DTS
Generic platform:
- Move Boston and NI 169445 FIT image source to their own files
- Include asm/bootinfo.h for plat_fdt_relocated()
- Include asm/time.h for get_c0_*_int()
- Include asm/bootinfo.h for plat_fdt_relocated()
- Include asm/time.h for get_c0_*_int()
- Allow filtering enabled boards by requirements
- Don't explicitly disable CONFIG_USB_SUPPORT
- Bump default NR_CPUS to 16
JZ4700:
- Probe the jz4740-rtc driver from devicetree
Lantiq:
- Drop check of boot select from the spi-falcon driver.
- Drop check of boot select from the lantiq-flash MTD driver.
- Access boot cause register in the watchdog driver through regmap
- Add device tree binding documentation for the watchdog driver
- Add docs for the RCU DT bindings.
- Convert the fpi bus driver to a platform_driver
- Remove ltq_reset_cause() and ltq_boot_select(
- Switch to a proper reset driver
- Switch to a new drivers/soc GPHY driver
- Add an USB PHY driver for the Lantiq SoCs using the RCU module
- Use of_platform_default_populate instead of __dt_register_buses
- Enable MFD_SYSCON to be able to use it for the RCU MFD
- Replace ltq_boot_select() with dummy implementation.
Loongson 2F:
- Allow NULL clock for clk_get_rate
Malta:
- Use new GIC accessor functions
NI 169445:
- Add support for NI 169445 board.
- Only include in 32r2el kernels
Octeon:
- Add support for watchdog of 78XX SOCs.
- Add support for watchdog of CN68XX SOCs.
- Expose support for mips32r1, mips32r2 and mips64r1
- Enable more drivers in config file
- Add support for accessing the boot vector.
- Remove old boot vector code from watchdog driver
- Define watchdog registers for 70xx, 73xx, 78xx, F75xx.
- Make CSR functions node aware.
- Allow access to CIU3 IRQ domains.
- Misc cleanups in the watchdog driver
Omega2+:
- New board, add support and defconfig
Pistachio:
- Enable Root FS on NFS in defconfig
Ralink:
- Add Mediatek MT7628A SoC
- Allow NULL clock for clk_get_rate
- Explicitly request exclusive reset control in the pci-mt7620 PCI driver.
SEAD3:
- Only include in 32 bit kernels by default
VoCore:
- Add VoCore as a vendor t0 dt-bindings
- Add defconfig file"
* '4.14-features' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (167 commits)
MIPS: Refactor handling of stack pointer in get_frame_info
MIPS: Stacktrace: Fix microMIPS stack unwinding on big endian systems
MIPS: microMIPS: Fix decoding of swsp16 instruction
MIPS: microMIPS: Fix decoding of addiusp instruction
MIPS: microMIPS: Fix detection of addiusp instruction
MIPS: Handle non word sized instructions when examining frame
MIPS: ralink: allow NULL clock for clk_get_rate
MIPS: Loongson 2F: allow NULL clock for clk_get_rate
MIPS: BCM63XX: allow NULL clock for clk_get_rate
MIPS: AR7: allow NULL clock for clk_get_rate
MIPS: BCM63XX: fix ENETDMA_6345_MAXBURST_REG offset
mips: Save all registers when saving the frame
MIPS: Add DWARF unwinding to assembly
MIPS: Make SAVE_SOME more standard
MIPS: Fix issues in backtraces
MIPS: jz4780: DTS: Probe the jz4740-rtc driver from devicetree
MIPS: Ci20: Enable RTC driver
watchdog: octeon-wdt: Add support for 78XX SOCs.
watchdog: octeon-wdt: Add support for cn68XX SOCs.
watchdog: octeon-wdt: File cleaning.
...
mei_cl_device_id are not supposed to change at runtime. All functions
working with mei_cl_device_id provided by <linux/mei_cl_bus.h> work
with const mei_cl_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
pnp_device_id are not supposed to change at runtime. All functions
working with pnp_device_id provided by <linux/pnp.h> work with
const pnp_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On Renesas R-Car archs, RuntimePM does all the clock handling. So, use
it consistently to enable/disable the clocks. Also make sure that clocks
are really enabled around clk_get_rate(). clk_summary looks proper now:
clock enable_cnt prepare_cnt rate ...
Before this commit:
At boot: rwdt 1 1 32768 0 0
WDT running: rwdt 2 2 32768 0 0
After this commit:
At boot: rwdt 0 1 32768 0 0
WDT running rwdt 1 1 32768 0 0
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add support for configuring the drive strength and polarity on the
AST2500, and the pulse duration on both the AST2400 and AST2500.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Tested-by: Matt Spinler <mspinler@linux.vnet.ibm.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Reference the system device tree when configuring the watchdog
engines. If property 'aspeed,reset_type' is present then set
reset behavior based on the specified value. This can be one of
three different mutually exclusive values
* cpu - Reset CPU only on watchdog timeout
* soc - Reset System on Chip
* system - Full system reset
No reset can also be specified by indicating:
* none - No reset, assumes another watchdog is responsible for
this.
Add optional property 'aspeed,external-signal'. If present then
configure to generate external signal on watchdog timeout.
Signed-off-by: Christopher Bostic <cbostic@linux.vnet.ibm.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
...da9063_watchdog, which contained nothing but struct watchdog_device and a
struct da9063 pointer.
Assign the struct da9063 pointer directly to the struct watchdog_device's
driver_data field instead of creating struct da9063_watchdog and assigning
it's address there.
Spares a pointer's size data memory and an indirection level in the callbacks.
Signed-off-by: Karsten Wiese <fzuuzf@googlemail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
platform_get_resource() may fail, so we should better check its
return value and propagate an error in case it fails.
This avoids a NULL pointer dereference a bit later in the code.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Improve CLK handling in the code to read freq via CCF.
Also disable CLK asap and add clk handling code to start and stop.
Signed-off-by: Maulik Jodhani <maulik.jodhani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
platform_device_id are not supposed to change at runtime. All functions
working with platform_device_id provided by <linux/platform_device.h>
work with const platform_device_id. So mark the non-const structs as
const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Showing message that driver is loaded is common across drivers.
This change also fixes checkpatch (--strict) warning
"Alignment should match open parenthesis".
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Give read access to module parameters to all and write access to root.
This change also improves driver error path testing.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
These watchdog_ops and watchdog_info structures are only stored
in the ops and info fields of a watchdog_device structure,
respectively, which are const. Thus make the watchdog_ops and
watchdog_info structures const as well.
Done with the help of Coccinelle. The rules for the watchdog_ops case are
as follows:
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct watchdog_ops i@p = { ... };
@ok@
identifier r.i;
struct watchdog_device e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct watchdog_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct watchdog_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
We should never return more time left than there actually is. So, switch
to a plain divider instead of DIV_ROUND_CLOSEST.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
If we set RWTCSRB to 0, we can gain 4096 as another divider value. This
is supported by all R-Car Gen2 and Gen3 devices which we aim to support.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The error margin of the clks_per_second variable was too large and
caused offsets when used with clock frequencies which left a remainder
after applying the dividers. Now we always calculate directly using the
clock rate and the divider using some helper macros. That also means
that DIV_ROUND_UP moves from probe to the multiplication macro. In
probe, we don't need to ensure anymore that 'clks_per_sec' would go too
fast but rather ensure that the lower limit is really at least 1 to
certainly get a full cycle.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
We should never return more time left than there actually is. So, switch
to a plain divider instead of DIV_ROUND_CLOSEST.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
When checking the clock rate, ensure also that counting all 16 bits
takes at least one second to match the granularity of the framework.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Because the smallest clock divider we can select is 1, 'clks_per_sec'
must be the same type as 'rate'.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: linux-watchdog@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: linux-watchdog@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: linux-watchdog@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: linux-watchdog@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The watchdog IP block on Meson8 and Meson8m2 is already supported by the
existing meson-wdt driver. Meson8 uses the same register bits as Meson6,
while the newer Meson8m2 SoC uses the same register bits as Meson8b.
Currently watchdog support on Meson8 SoC already works because
meson8.dtsi simply uses the "amlogic,meson6-wdt" compatible. Adding a
separate compatible for Meson8 makes this more explicit though.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Don't populate array chip_name on the stack but instead make it static.
Makes the object code smaller by 40 bytes:
Before:
text data bss dec hex filename
5641 2840 384 8865 22a1 drivers/watchdog/w83627hf_wdt.o
After:
text data bss dec hex filename
5545 2896 384 8825 2279 drivers/watchdog/w83627hf_wdt.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Check for watchdog_ops structures that are only stored in the ops field of
a watchdog_device structure. This field is declared const, so watchdog_ops
structures that have this property can be declared as const also.
This issue was detected using Coccinelle and the following semantic patch:
@r
disable optional_qualifier@
identifier i;
position p;
@@
static struct watchdog_ops i@p = { ... };
@ok@
identifier r.i;
struct watchdog_device e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct watchdog_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct watchdog_ops i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Check for watchdog_ops structures that are only stored in the ops field of
a watchdog_device structure. This field is declared const, so watchdog_ops
structures that have this property can be declared as const also.
This issue was detected using Coccinelle and the following semantic patch:
@r
disable optional_qualifier@
identifier i;
position p;
@@
static struct watchdog_ops i@p = { ... };
@ok@
identifier r.i;
struct watchdog_device e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct watchdog_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct watchdog_ops i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Check for watchdog_ops structures that are only stored in the ops field of
a watchdog_device structure. This field is declared const, so watchdog_ops
structures that have this property can be declared as const also.
This issue was detected using Coccinelle and the following semantic patch:
@r
disable optional_qualifier@
identifier i;
position p;
@@
static struct watchdog_ops i@p = { ... };
@ok@
identifier r.i;
struct watchdog_device e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct watchdog_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct watchdog_ops i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Check for watchdog_ops structures that are only stored in the ops field of
a watchdog_device structure. This field is declared const, so watchdog_ops
structures that have this property can be declared as const also.
This issue was detected using Coccinelle and the following semantic patch:
@r
disable optional_qualifier@
identifier i;
position p;
@@
static struct watchdog_ops i@p = { ... };
@ok@
identifier r.i;
struct watchdog_device e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct watchdog_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct watchdog_ops i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This reverts commit 1fccb73011.
Reported as Bug 196509 - iTCO_wdt regression reboot before timeout expire
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
* Update copyright and company name.
* Remove unused headers.
* Fix variable spelling and data type.
* Use octal values for module parameters.
Signed-off-by: Steven J. Hill <steven.hill@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Cc: linux-mips@linux-mips.org
Cc: linux-watchdog@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/17212/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pull watchdog updates from Wim Van Sebroeck:
- Add Renesas RZ/A WDT Watchdog driver
- STM32 Independent WatchDoG (IWDG) support
- UniPhier watchdog support
- Add F71868 support
- Add support for NCT6793D and NCT6795D
- dw_wdt: add reset lines support
- core: add option to avoid early handling of watchdog
- core: introduce watchdog_worker_should_ping helper
- Cleanups and improvements for sama5d4, intel-mid_wdt, s3c2410_wdt,
orion_wdt, gpio_wdt, it87_wdt, meson_wdt, davinci_wdt, bcm47xx_wdt,
zx2967_wdt, cadence_wdt
* git://www.linux-watchdog.org/linux-watchdog: (32 commits)
watchdog: introduce watchdog_worker_should_ping helper
watchdog: uniphier: add UniPhier watchdog driver
dt-bindings: watchdog: add description for UniPhier WDT controller
watchdog: cadence_wdt: make of_device_ids const.
watchdog: zx2967: constify zx2967_wdt_ops.
watchdog: bcm47xx_wdt: constify bcm47xx_wdt_hard_ops and bcm47xx_wdt_soft_ops
watchdog: davinci: Add missing clk_disable_unprepare().
watchdog: davinci: Handle return value of clk_prepare_enable
watchdog: meson: Handle return value of clk_prepare_enable
watchdog: it87: Add support for various Super-IO chips
watchdog: it87: Use infrastructure to stop watchdog on reboot
watchdog: it87: Drop support for resetting watchdog though CIR and Game port
watchdog: it87: Convert to use watchdog core infrastructure
watchdog: it87: Drop FSF mailing address
watchdog: dw_wdt: get reset lines from dt
watchdog: bindings: dw_wdt: add reset lines
watchdog: w83627hf: Add support for NCT6793D and NCT6795D
watchdog: core: add option to avoid early handling of watchdog
watchdog: f71808e_wdt: Add F71868 support
watchdog: Add STM32 IWDG driver
...
This will be useful when the condition becomes slightly more
complicated in the next patch.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Esben Haabendal <esben@haabendal.dk>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add a watchdog driver for Socionext UniPhier series SoC.
Note that the timeout value for this device must be a power
of 2 because of the specification.
Signed-off-by: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
of_device_ids are not supposed to change at runtime. All functions
working with of_device_ids provided by <linux/of.h> work with const
of_device_ids. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
1962 612 4 2578 a12 drivers/watchdog/cadence_wdt.o
File size after constify cdns_wdt_of_match:
text data bss dec hex filename
2378 196 4 2578 a12 drivers/watchdog/cadence_wdt.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
davinci_wdt_probe() can fail here and we must disable clock.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add support for IT8607, IT8622, IT8625, IT8628, IT8655, IT8665,
and IT8686.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use watchdog_stop_on_reboot() to stop the watchdog on reboot instead
of registering a driver-specific notifier.
While at it, reorder remaining include files alphabetically.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Resetting the watchdog timer on CIR interrupts or on game port interrupts
is not not supported on recent chips, and doesn't really tell if the system
is stable. On top of that, at least the bit to enable resetting the
watchdog through the game port is used differently on recent chips.
Drop resetting the watchdog on CIR or game port interrupts to simplify
the code.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The dw_wdt has an external reset line, that can keep the device in reset
and therefore rendering it useless and also is the only way of stopping
the watchdog once it was started.
Get the reset lines for this core from the devicetree. As these lines are
optional, use devm_reset_control_get_optional_shared. If the reset line
is not specified in the devicetree, the reset framework will just skip
deasserting and continue.
This way all users of the driver will continue to function without
any harm, even if the reset line is not specified in the devicetree.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: linux-watchdog@vger.kernel.org
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
drivers/watchdog/wdrtas.c uses symbols defined in arch/powerpc/kernel/rtas.c,
which are exported iff CONFIG_PPC_RTAS is selected. Building wdrtas.c without
setting CONFIG_PPC_RTAS throws the following errors:
ERROR: ".rtas_token" [drivers/watchdog/wdrtas.ko] undefined!
ERROR: "rtas_data_buf" [drivers/watchdog/wdrtas.ko] undefined!
ERROR: "rtas_data_buf_lock" [drivers/watchdog/wdrtas.ko] undefined!
ERROR: ".rtas_get_sensor" [drivers/watchdog/wdrtas.ko] undefined!
ERROR: ".rtas_call" [drivers/watchdog/wdrtas.ko] undefined!
This was identified during a randconfig build where CONFIG_WATCHDOG_RTAS=m and
CONFIG_PPC_RTAS was not set. Logs are here:
http://kisskb.ellerman.id.au/kisskb/buildresult/12982152/
This patch fixes the issue by updating CONFIG_WATCHDOG_RTAS to depend on just
CONFIG_PPC_RTAS, removing COMPILE_TEST entirely.
Signed-off-by: Murilo Opsfelder Araujo <mopsfelder@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Both NCT6793D and NCT6795D are compatible to NCT6792D.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On some systems its desirable to have watchdog reboot the system
when it does not come up fast enough. This adds a kernel parameter
to disable the auto-update of watchdog before userspace takes over
and a kernel option to set the default. The info messages were
added to shorten error searching on misconfigured systems.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This adds support for watchdog part of Fintek F71868 Super I/O chip to
f71808e_wdt driver.
The F71868 chip is, in general, very similar to a F71869, however it has
slightly different set of available reset pulse widths.
Tested on MSI A55M-P33 motherboard.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The watchdog infrastructure now supports handling watchdog keepalive
if the watchdog is running while the watchdog device is closed.
The infrastructure now also supports generating additional heartbeats
if the maximum hardware timeout is smaller than or close to the
configured timeout. Convert the driver to use this infrastructure.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The header says: This file is licensed under the terms of the GNU
General Public License version 2. The right identifier for
MODULE_LICENSE is "GPL v2" then.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cleanup the code from minor readability issues (no functional changes):
1. Fix checkpatch: ERROR: Do not include the paragraph about writing to
the Free Software Foundation's mailing address.
2. Fix checkpatch: WARNING: quoted string split across lines
3. Fix chechpatch: WARNING: Prefer 'unsigned int' to bare use of
'unsigned'
4. Use 'dev' consistently in probe function instead of mixing dev with
&pdev->dev.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Simplify the flow in helper function for getting the driver data by
using of_device_get_match_data() and only one if() branch.
The code should be equivalent.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Structures watchdog_device, watchdog_ops and s3c2410_wdt_variant are not
modified so they can be made const to increase code safeness.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Firmware followed by bootloader leaves watchdog running.
Keep it running in the driver.
User will not need any additional options to reboot in case of panic
during boot.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Adds a watchdog timer driver for the Renesas RZ/A Series SoCs. A reset
handler is also included since a WDT overflow is the only method for
restarting an RZ/A SoC.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Because suspending to RAM may lose the register values, they are restored
on resume. This is currently done unconditionally because there is
currently no way to know (from the driver) whether they have really been
lost or are still valid. Writing MR also pings the watchdog and this may
not be what is expected so add a comment explaining why it happens.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Because the only way to use the driver is to have a device tree enabling
it, pdev->dev.of_node will never be NULL. Remove the unnecessary check.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The ICH9 is listed as having TCO v2, and indeed the behavior in the
datasheet corresponds to v2 (for example the NO_REBOOT flag is
accessible via the 16KiB-aligned Root Complex Base Address).
However, the TCO counts twice just like in v1; the documentation
of the SECOND_TO_STS bit says: "ICH9 sets this bit to 1 to indicate
that the TIMEOUT bit had been (or is currently) set and a second
timeout occurred before the TCO_RLD register was written. If this
bit is set and the NO_REBOOT config bit is 0, then the ICH9 will
reboot the system after the second timeout. The same can be found
in the BayTrail (Atom E3800) datasheet, and even HOWTOs around
the Internet say that it will reboot after _twice_ the specified
heartbeat.
I did not find the Apollo Lake datasheet, but because v4/v5 has
a SECOND_TO_STS bit just like the previous version I'm enabling
this for Apollo Lake as well.
Cc: linux-watchdog@vger.kernel.org
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
To fix following build error when SOFTWARE_REBOOT is defined:
CC [M] driver/watchdog/wdt_pci.o
driver/watchdog/wdt_pci.c: In function 'wdtpci_interrupt':
driver/watchdog/wdt_pci.c:335:3: error: too many arguments to function 'emergency_restart'
emergency_restart(NULL);
^
In file included from driver/watchdog/wdt_pci.c:51:0:
include/linux/reboot.h:80:13: note: declared here
extern void emergency_restart(void);
^
Signed-off-by: Shile Zhang <shile.zhang@nokia.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
wdt_timeout must not be initialized to CDNS_WDT_DEFAULT_TIMEOUT in
order to allow the value to be overriddden by a device tree setting.
This way, the default timeout value will be used only in case module_param
has not been set, or device tree timeout-sec has not been defined.
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
WDT_MR and WDT_CR must not updated within three slow clock periods after
the last ping (write to WDT_CR or WDT_MR). Ensure enough time has elapsed
before writing those registers.
wdt_write() waits for 4 periods to ensure at least 3 edges are seen by the
IP.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Wenyou.Yang <wenyou.yang@microchip.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The datasheet states: "When setting the WDDIS bit, and while it is set, the
fields WDV and WDD must not be modified."
Because the whole configuration is already cached inside .mr, wait for the
user to enable the watchdog to configure it so it is enabled and configured
at the same time (what the IP is actually expecting).
When the watchdog is already enabled, it is not an issue to reconfigure it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Wenyou.Yang <wenyou.yang@microchip.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
I ran into one corner case with the orion watchdog using the
atomic_io_modify interface:
drivers/watchdog/orion_wdt.o: In function `orion_stop':
orion_wdt.c:(.text.orion_stop+0x28): undefined reference to `atomic_io_modify'
drivers/watchdog/orion_wdt.o: In function `armada375_stop':
orion_wdt.c:(.text.armada375_stop+0x28): undefined reference to `atomic_io_modify'
This function is available on all 32-bit ARM builds except for ebsa110, so
we have to specifically exclude that from compile-testing.
Fixes: da2a68b3eb ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
-----BEGIN PGP SIGNATURE-----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=lbS7
-----END PGP SIGNATURE-----
Merge tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull hw lockdown support from David Howells:
"Annotation of module parameters that configure hardware resources
including ioports, iomem addresses, irq lines and dma channels.
This allows a future patch to prohibit the use of such module
parameters to prevent that hardware from being abused to gain access
to the running kernel image as part of locking the kernel down under
UEFI secure boot conditions.
Annotations are made by changing:
module_param(n, t, p)
module_param_named(n, v, t, p)
module_param_array(n, t, m, p)
to:
module_param_hw(n, t, hwtype, p)
module_param_hw_named(n, v, t, hwtype, p)
module_param_hw_array(n, t, hwtype, m, p)
where the module parameter refers to a hardware setting
hwtype specifies the type of the resource being configured. This can
be one of:
ioport Module parameter configures an I/O port
iomem Module parameter configures an I/O mem address
ioport_or_iomem Module parameter could be either (runtime set)
irq Module parameter configures an I/O port
dma Module parameter configures a DMA channel
dma_addr Module parameter configures a DMA buffer address
other Module parameter configures some other value
Note that the hwtype is compile checked, but not currently stored (the
lockdown code probably won't require it). It is, however, there for
future use.
A bonus is that the hwtype can also be used for grepping.
The intention is for the kernel to ignore or reject attempts to set
annotated module parameters if lockdown is enabled. This applies to
options passed on the boot command line, passed to insmod/modprobe or
direct twiddling in /sys/module/ parameter files.
The module initialisation then needs to handle the parameter not being
set, by (1) giving an error, (2) probing for a value or (3) using a
reasonable default.
What I can't do is just reject a module out of hand because it may
take a hardware setting in the module parameters. Some important
modules, some ipmi stuff for instance, both probe for hardware and
allow hardware to be manually specified; if the driver is aborts with
any error, you don't get any ipmi hardware.
Further, trying to do this entirely in the module initialisation code
doesn't protect against sysfs twiddling.
[!] Note that in and of itself, this series of patches should have no
effect on the the size of the kernel or code execution - that is
left to a patch in the next series to effect. It does mark
annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
an already existing field"
* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
Annotate hardware config module parameters in sound/pci/
Annotate hardware config module parameters in sound/oss/
Annotate hardware config module parameters in sound/isa/
Annotate hardware config module parameters in sound/drivers/
Annotate hardware config module parameters in fs/pstore/
Annotate hardware config module parameters in drivers/watchdog/
Annotate hardware config module parameters in drivers/video/
Annotate hardware config module parameters in drivers/tty/
Annotate hardware config module parameters in drivers/staging/vme/
Annotate hardware config module parameters in drivers/staging/speakup/
Annotate hardware config module parameters in drivers/staging/media/
Annotate hardware config module parameters in drivers/scsi/
Annotate hardware config module parameters in drivers/pcmcia/
Annotate hardware config module parameters in drivers/pci/hotplug/
Annotate hardware config module parameters in drivers/parport/
Annotate hardware config module parameters in drivers/net/wireless/
Annotate hardware config module parameters in drivers/net/wan/
Annotate hardware config module parameters in drivers/net/irda/
Annotate hardware config module parameters in drivers/net/hamradio/
Annotate hardware config module parameters in drivers/net/ethernet/
...
set_memory_* functions have moved to set_memory.h. Switch to this
explicitly.
Link: http://lkml.kernel.org/r/1488920133-27229-10-git-send-email-labbott@redhat.com
Signed-off-by: Laura Abbott <labbott@redhat.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In some SoCs, setting noreboot bit needs modification to
PMC GC registers. But not all PMC drivers allow other drivers
to memory map their GC region. This could create mem request
conflict in watchdog driver. So this patch adds facility to allow
PMC drivers to pass noreboot update function to watchdog
drivers via platform data.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
iTCO_wdt no_reboot_bit set/unset functions has lot of common code between
them. So merging these two functions into a single update function would
remove these unnecessary code duplications. This patch fixes this issue
by creating a no_reboot_bit update function to handle both set/unset
functions.
Also checking for iTCO version every time you make no_reboot_bit set/unset
call is inefficient and makes the code look complex. This can be improved
by performing this check once during device probe and selecting the
appropriate no_reboot_bit update function. This patch fixes this issue
by splitting the update function into multiple helper functions.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
When the kernel is running in secure boot mode, we lock down the kernel to
prevent userspace from modifying the running kernel image. Whilst this
includes prohibiting access to things like /dev/mem, it must also prevent
access by means of configuring driver modules in such a way as to cause a
device to access or modify the kernel image.
To this end, annotate module_param* statements that refer to hardware
configuration and indicate for future reference what type of parameter they
specify. The parameter parser in the core sees this information and can
skip such parameters with an error message if the kernel is locked down.
The module initialisation then runs as normal, but just sees whatever the
default values for those parameters is.
Note that we do still need to do the module initialisation because some
drivers have viable defaults set in case parameters aren't specified and
some drivers support automatic configuration (e.g. PNP or PCI) in addition
to manually coded parameters.
This patch annotates drivers in drivers/watchdog/.
Suggested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
cc: Wim Van Sebroeck <wim@iguana.be>
cc: Zwane Mwaikambo <zwanem@gmail.com>
cc: linux-watchdog@vger.kernel.org
The retu watchdog calls into the respective mfd driver, but fails to
link if that is diabled:
drivers/watchdog/built-in.o: In function `retu_wdt_set_timeout':
ziirave_wdt.c:(.text+0x8c88): undefined reference to `retu_write'
ziirave_wdt.c:(.text+0x8c88): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `retu_write'
drivers/watchdog/built-in.o: In function `retu_wdt_start':
ziirave_wdt.c:(.text+0x8cc8): undefined reference to `retu_write'
ziirave_wdt.c:(.text+0x8cc8): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `retu_write'
This restores the dependency as it was before
Fixes: da2a68b3eb ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When the db8500 watchdog is enabled without the PRCMU, we get a lot of
warnings about duplicate or missing helper functions:
In file included from drivers/watchdog/ux500_wdt.c:21:0:
include/linux/mfd/dbx500-prcmu.h:422:19: error: redefinition of 'prcmu_abb_read'
static inline int prcmu_abb_read(u8 slave, u8 reg, u8 *value, u8 size)
This restores the dependency as it was.
Fixes: da2a68b3eb ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
gcc-4.3 can't decide whether the constant value in
kempld_prescaler[PRESCALER_21] is built-time constant or
not, and gets confused by the logic in do_div():
drivers/watchdog/kempld_wdt.o: In function `kempld_wdt_set_stage_timeout':
kempld_wdt.c:(.text.kempld_wdt_set_stage_timeout+0x130): undefined reference to `__aeabi_uldivmod'
This adds a call to ACCESS_ONCE() to force it to not consider
it to be constant, and leaves the more efficient normal case
in place for modern compilers, using an #ifdef to annotate
why we do this hack.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Checking for timer expiration is done from the softirq TIMER_SOFTIRQ.
Since commit 4cd13c21b2 ("softirq: Let ksoftirqd do its job"),
pending softirqs are no longer always handled immediately, instead,
if there are pending softirqs, and ksoftirqd is in state TASK_RUNNING,
the handling of the softirqs are deferred, and are instead supposed
to be handled by ksoftirqd, when ksoftirqd gets scheduled.
If a user space process with a real-time policy starts to misbehave
by never relinquishing the CPU while ksoftirqd is in state TASK_RUNNING,
what will happen is that all softirqs will get deferred, while ksoftirqd,
which is supposed to handle the deferred softirqs, will never get to run.
To make sure that the watchdog is able to fire even when we do not get
to run softirqs, replace the timers with hrtimers.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The kempld watchdog driver requires the respective MFD driver:
drivers/watchdog/built-in.o: In function `kempld_wdt_probe':
kempld_wdt.c:(.text+0x5c78): undefined reference to `kempld_get_mutex'
kempld_wdt.c:(.text+0x5c84): undefined reference to `kempld_read8'
kempld_wdt.c:(.text+0x5c8e): undefined reference to `kempld_release_mutex'
kempld_wdt.c:(.text+0x5d1c): undefined reference to `kempld_read8'
kempld_wdt.c:(.text+0x5d2c): undefined reference to `kempld_write8'
This adds the Kconfig dependency back.
Fixes: da2a68b3eb ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Without CONFIG_OF, the driver fails to link:
drivers/watchdog/built-in.o: In function `bcm2835_power_off':
bcm2835_wdt.c:(.text+0x1946): undefined reference to `of_find_device_by_node'
This adds a new dependency, to allow the COMPILE_TEST check to succeed.
Fixes: da2a68b3eb ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver fails to link if ARM_AMBA is disabled:
drivers/watchdog/sp805_wdt.o: In function `sp805_wdt_driver_init':
sp805_wdt.c:(.init.text+0x4): undefined reference to `amba_driver_register'
It seems that the COMPILE_TEST was added in the wrong place, as there
is no architecture dependency, but a bus dependency. This moves
the dependency accordingly.
Fixes: da2a68b3eb ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver fails to link when CONFIG_I2C is disabled or a loadable module while
the watchdog is built-in:
drivers/watchdog/built-in.o: In function `menf21bmc_wdt_shutdown':
menf21bmc_wdt.c:(.text+0x9b44): undefined reference to `i2c_smbus_write_word_data'
menf21bmc_wdt.c:(.text+0x9b44): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `i2c_smbus_write_word_data'
This adds a Kconfig dependency for it, to enforce a valid configuration.
Fixes: da2a68b3eb ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Wtihout CONFIG_CS5535_MFGPT, the driver does not link right:
drivers/watchdog/built-in.o: In function `geodewdt_probe':
geodewdt.c:(.init.text+0xca3): undefined reference to `cs5535_mfgpt_alloc_timer'
geodewdt.c:(.init.text+0xcd4): undefined reference to `cs5535_mfgpt_write'
geodewdt.c:(.init.text+0xcef): undefined reference to `cs5535_mfgpt_toggle_event'
This adds back the dependency on this base driver.
Fixes: da2a68b3eb ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The wm831x watchdog driver can now be built without the wm831x mfd
driver, which results in a link error:
(.text+0x1a95c): undefined reference to `wm831x_set_bits'
(.text+0x1a95c): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `wm831x_set_bits'
(.text+0x1a968): undefined reference to `wm831x_reg_lock'
(.text+0x1a968): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `wm831x_reg_lock'
(.text+0x1a9dc): undefined reference to `wm831x_reg_unlock'
(.text+0x1a9dc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `wm831x_reg_unlock'
This adds back the dependency that was removed. We can still build test
this driver on all architectures by enabling the MFD driver for it first.
Fixes: da2a68b3eb ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix typos and add the following to the scripts/spelling.txt:
partiton||partition
Link: http://lkml.kernel.org/r/1481573103-11329-7-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Functions marked static inline might not be inlined so a driver-specific
prefix for function name helps when looking through call backtrace.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Syscon is used not only on Exynos5 SoCs but also on Exynos3250,
Exynos4412 and ARMv8 versions (Exynos5433, Exynos7).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Replace the 'debug' module parameter and pr_info() with proper device
dynamic debug calls because this is the preferred and flexible way of
enabling debugging printks.
Also remove some obvious debug printks.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In soft (no-reboot) mode, the driver self-pings watchdog upon expiration
of an interrupt. However the interrupt itself was not cleared thus on
first hit, the system enters infinite interrupt handling loop.
On Odroid U3 (Exynos4412), when booted with s3c2410_wdt.soft_noboot=1
argument the console is flooded:
# killall -9 watchdog
[ 60.523760] s3c2410-wdt 10060000.watchdog: watchdog timer expired (irq)
[ 60.536744] s3c2410-wdt 10060000.watchdog: watchdog timer expired (irq)
Fix this by writing something to the WTCLRINT register to clear the
interrupt. The register WTCLRINT however appeared in S3C6410 so a new
watchdog quirk and flavor are needed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The CONFIG prefix from defines in the s3c2410_wdt.c might suggest that
these constants come from Kconfig.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It occurred to me that the panic pretimeout governor will stall the
softdog, because it is purely software which simply breaks when the
kernel panics. Testing governors with the softdog on the other hand is
really useful, so make this feature a compile time option which nees to
be enabled explicitly. This also removes the overhead if pretimeout
support is not used because it will now be compiled away (saving ~10% on
ARM32).
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When resuming for the deepest state on sama5d2, it is necessary to restore
MR as the registers are lost.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
.config is used to cache a part of WDT_MR at probe time and is not used
afterwards. Instead of doing that, actually cache MR and avoid reading it
every time it is modified.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cleanup this driver and convert it to use the watchdog framework API.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Mika Westerberg <mika.westerberg@iki.fi>
[groeck: Dropped initialization of static variable]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cleanup this driver and remove the 200ms heartbeat timer. The core now
has the ability to handle the heartbeat.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
[groeck: Dropped 0-initialization of static variable]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Without this dependency, platforms not supporting PCI (such as m68k)
report the following build warning when building allmodconfig
or allyesconfig.
drivers/watchdog/rdc321x_wdt.c: In function 'rdc321x_wdt_ioctl':
./arch/m68k/include/asm/uaccess_mm.h:61:1: warning:
'value' may be used uninitialized in this function
Fixes: f4c3de659054 ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This add support for the Cortina systems Gemini (SL3516)
SoC watchdog.
I have tried to use all the right new kernel interfaces
and tested with busybox' "watchdog" command both to kick
and get timeouts and reboots.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Declare watchdog_ops structures as const as they are only stored in the
ops field of a watchdog_device structure. This field is of type const, so
watchdog_ops structures having this property can be made const too.
Done using Coccinelle:
@r disable optional_qualifier@
identifier x;
position p;
@@
static struct watchdog_ops x@p={...};
@ok@
struct watchdog_device w;
identifier r.x;
position p;
@@
w.ops=&x@p;
@bad@
position p != {r.p,ok.p};
identifier r.x;
@@
x@p
@depends on !bad disable optional_qualifier@
identifier r.x;
@@
+const
struct watchdog_ops x;
File size details before and after patching.
First line of every .o file shows the file size before patching
and second line shows the size after patching.
text data bss dec hex filename
1340 544 0 1884 75c drivers/watchdog/bcm_kona_wdt.o
1436 440 0 1876 754 drivers/watchdog/bcm_kona_wdt.o
1176 544 4 1724 6bc drivers/watchdog/digicolor_wdt.o
1272 440 4 1716 6b4 drivers/watchdog/digicolor_wdt.o
925 580 89 1594 63a drivers/watchdog/ep93xx_wdt.o
1021 476 89 1586 632 drivers/watchdog/ep93xx_wdt.o
4932 288 17 5237 1475 drivers/watchdog/s3c2410_wdt.o
5028 192 17 5237 1475 drivers/watchdog/s3c2410_wdt.o
1977 292 1 2270 8de drivers/watchdog/sama5d4_wdt.o
2073 196 1 2270 8de drivers/watchdog/sama5d4_wdt.o
1375 484 1 1860 744 drivers/watchdog/sirfsoc_wdt.o
1471 380 1 1852 73c drivers/watchdog/sirfsoc_wdt.o
Size remains the same for the files drivers/watchdog/diag288_wdt.o
drivers/watchdog/asm9260_wdt.o and drivers/watchdog/atlas7_wdt.o
The following .o files did not compile:
drivers/watchdog/sun4v_wdt.o, drivers/watchdog/sbsa_gwdt.o,
drivers/watchdog/rt2880_wdt.o, drivers/watchdog/booke_wdt.o
drivers/watchdog/mt7621_wdt.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Many watchdog drivers explicitly stop the watchdog when unregistering it.
While it is unclear if this is actually needed (the whatdog should not be
running at that time if it can be stopped), introduce a helper to
explicitly stop the watchdog in the watchdog core when unregistering it.
This helps reducing driver code size while retaining functionality.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The devm_ resource manager functions allow memory to be automatically
released when a device is unbound. This patch takes advantage of the
resource manager functions and replaces the watchdog_register_device
call with the devm_watchdog_register_device call. In addition, the
ebc_c384_wdt_remove function has been removed as no longer necessary due
to the use of the relevant devm_ resource manager functions.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use device managed functions to simplify error handling, reduce
source code size, improve readability, and reduce the likelyhood of bugs.
The conversion was done automatically with coccinelle using the
following semantic patches. The semantic patches and the scripts used
to generate this commit log are available at
https://github.com/groeck/coccinelle-patches
- Use devm_watchdog_register_driver() to register watchdog device
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use device managed functions to simplify error handling, reduce
source code size, improve readability, and reduce the likelyhood of bugs.
The conversion was done automatically with coccinelle using the
following semantic patches. The semantic patches and the scripts used
to generate this commit log are available at
https://github.com/groeck/coccinelle-patches
- Replace 'val = e; return val;' with 'return e;'
- Replace 'if (e) return e; return 0;' with 'return e;'
- Drop assignments to otherwise unused variables
- Drop unused variables
- Drop remove function
- Drop dev_set_drvdata()
- Use devm_watchdog_register_driver() to register watchdog device
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use device managed functions to simplify error handling, reduce
source code size, improve readability, and reduce the likelyhood of bugs.
The conversion was done automatically with coccinelle using the
following semantic patches. The semantic patches and the scripts used
to generate this commit log are available at
https://github.com/groeck/coccinelle-patches
- Replace 'val = e; return val;' with 'return e;'
- Drop assignments to otherwise unused variables
- Drop remove function
- Drop dev_set_drvdata()
- Use devm_watchdog_register_driver() to register watchdog device
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use device managed functions to simplify error handling, reduce
source code size, improve readability, and reduce the likelyhood of bugs.
The conversion was done automatically with coccinelle using the
following semantic patches. The semantic patches and the scripts used
to generate this commit log are available at
https://github.com/groeck/coccinelle-patches
- Replace 'goto l; ... l: return e;' with 'return e;'
- Drop assignments to otherwise unused variables
- Drop remove function
- Drop platform_set_drvdata()
- Use devm_watchdog_register_driver() to register watchdog device
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use device managed functions to simplify error handling, reduce
source code size, improve readability, and reduce the likelyhood of bugs.
The conversion was done automatically with coccinelle using the
following semantic patches. The semantic patches and the scripts used
to generate this commit log are available at
https://github.com/groeck/coccinelle-patches
- Replace 'goto l; ... l: return e;' with 'return e;'
- Replace 'val = e; return val;' with 'return e;'
- Drop assignments to otherwise unused variables
- Replace 'if (e) { return expr; }' with 'if (e) return expr;'
- Drop remove function
- Drop platform_set_drvdata()
- Use devm_watchdog_register_driver() to register watchdog device
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use device managed functions to simplify error handling, reduce
source code size, improve readability, and reduce the likelyhood of bugs.
Other improvements as listed below.
The conversion was done automatically with coccinelle using the
following semantic patches. The semantic patches and the scripts used
to generate this commit log are available at
https://github.com/groeck/coccinelle-patches
- Drop assignments to otherwise unused variables
- Replace of_iomap() with platform_get_resource() followed by
devm_ioremap_resource()
- Replace &pdev->dev with dev if 'struct device *dev' is a declared
variable
- Use devm_watchdog_register_driver() to register watchdog device
- Replace shutdown function with call to watchdog_stop_on_reboot()
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Lee Jones <lee@kernel.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use device managed functions to simplify error handling, reduce
source code size, improve readability, and reduce the likelyhood of bugs.
Other improvements as listed below.
The conversion was done automatically with coccinelle using the
following semantic patches. The semantic patches and the scripts used
to generate this commit log are available at
https://github.com/groeck/coccinelle-patches
- Replace 'goto l; ... l: return e;' with 'return e;'
- Drop assignments to otherwise unused variables
- Drop remove function
- Drop unnecessary mutex_destroy() on allocated data
- Use devm_watchdog_register_driver() to register watchdog device
Acked-by: Johannes Thumshirn <morbidrsa@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use device managed functions to simplify error handling, reduce
source code size, improve readability, and reduce the likelyhood of bugs.
The conversion was done automatically with coccinelle using the
following semantic patches. The semantic patches and the scripts used
to generate this commit log are available at
https://github.com/groeck/coccinelle-patches
- Replace 'goto l; ... l: return e;' with 'return e;'
- Replace 'val = e; return val;' with 'return e;'
- Drop assignments to otherwise unused variables
- Replace 'if (e) { return expr; }' with 'if (e) return expr;'
- Drop remove function
- Drop platform_set_drvdata()
- Use devm_watchdog_register_driver() to register watchdog device
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use device managed functions to simplify error handling, reduce
source code size, improve readability, and reduce the likelyhood of bugs.
Other improvements as listed below.
The conversion was done automatically with coccinelle using the
following semantic patches. The semantic patches and the scripts used
to generate this commit log are available at
https://github.com/groeck/coccinelle-patches
- Replace 'goto l; ... l: return e;' with 'return e;'
- Replace 'val = e; return val;' with 'return e;'
- Drop assignments to otherwise unused variables
- Replace 'if (e) { return expr; }' with 'if (e) return expr;'
- Drop remove function
- Replace of_iomap() with platform_get_resource() followed by
devm_ioremap_resource()
- Drop platform_set_drvdata()
- Replace &pdev->dev with dev if 'struct device *dev' is a declared
variable
- Use devm_watchdog_register_driver() to register watchdog device
- Replace shutdown function with call to watchdog_stop_on_reboot()
Acked-by: Baruch Siach <baruch@tkos.co.il>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The shutdown function calls the stop function.
Call watchdog_stop_on_reboot() from probe instead.
The conversion was done automatically with coccinelle using the
following semantic patches. The semantic patches and the scripts used
to generate this commit log are available at
https://github.com/groeck/coccinelle-patches
- Replace shutdown function with call to watchdog_stop_on_reboot()
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use device managed functions to simplify error handling, reduce
source code size, improve readability, and reduce the likelyhood of bugs.
The conversion was done automatically with coccinelle using the
following semantic patches. The semantic patches and the scripts used
to generate this commit log are available at
https://github.com/groeck/coccinelle-patches
- Drop assignments to otherwise unused variables
- Drop remove function
- Drop platform_set_drvdata()
- Use devm_watchdog_register_driver() to register watchdog device
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use device managed functions to simplify error handling, reduce
source code size, improve readability, and reduce the likelyhood of bugs.
Other improvements as listed below.
The conversion was done automatically with coccinelle using the
following semantic patches. The semantic patches and the scripts used
to generate this commit log are available at
https://github.com/groeck/coccinelle-patches
- Drop assignments to otherwise unused variables
- Drop remove function
- Drop platform_set_drvdata()
- Use devm_watchdog_register_driver() to register watchdog device
- Replace shutdown function with call to watchdog_stop_on_reboot()
Cc: Carlo Caione <carlo@caione.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use device managed functions to simplify error handling, reduce
source code size, improve readability, and reduce the likelyhood of bugs.
Other improvements as listed below.
The conversion was done automatically with coccinelle using the
following semantic patches. The semantic patches and the scripts used
to generate this commit log are available at
https://github.com/groeck/coccinelle-patches
- Drop assignments to otherwise unused variables
- Drop remove function
- Drop platform_set_drvdata()
- Use devm_watchdog_register_driver() to register watchdog device
- Replace shutdown function with call to watchdog_stop_on_reboot()
Cc: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use device managed functions to simplify error handling, reduce
source code size, improve readability, and reduce the likelyhood of bugs.
The conversion was done automatically with coccinelle using the
following semantic patches. The semantic patches and the scripts used
to generate this commit log are available at
https://github.com/groeck/coccinelle-patches
- Drop assignments to otherwise unused variables
- Drop remove function
- Drop platform_set_drvdata()
- Use devm_watchdog_register_driver() to register watchdog device
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use a local dev variable instead of dereferencing pdev->dev several
times in the probe function to make the code easier to read.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Enabling the clock before accessing chip registers and disabling it
afterwards does not really make sense and only adds complexity to
the driver. In addition to that, a comment int the driver suggests
that it does not serve a useful purpose either.
"The watchdog block is of course always clocked, the
clk_enable()/clk_disable() calls are mainly for performing reference
counting higher up in the clock hierarchy."
Just keep the clock enabled instead.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Checking if there is no error followed by a goto if there is one is
confusing. Reverse the logic.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use the infrastructure provided by the watchdog core to install
the restart handler.
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Platform data was already validated in the probe function. If it was NULL,
the remove function will never be called. Remove the unnecessary check.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The 'ret' variable in iTCO_wdt_init_module() does not add any value;
drop it.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use pdev for struct platform_device, pci_dev for struct pci_dev, and dev
for struct device variables to improve consistency.
Remove 'struct platform_device *dev;' from struct iTCO_wdt_private since
it was unused.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Using device managed resources simplifies error handling and cleanup,
and to reduce the likelyhood of errors.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Allocate private data and the watchdog device to avoid having
to clear it on remove and to enable subsequent simplifications.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Trivial fix to spelling mistake in WARN message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Building all watchdog drivers is all but impossible since many depend
on platforms which are not enabled by test builds. Add dependency on
COMPILE_TEST where possible to improve the situation.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pnx833x_wdt does not compile if enabled. Bit operations expect an unsigned
long as argument. If that is fixed, the build still fails because put_user,
get_user, and copy_to_user are undefined.
Mark it as broken.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the watchdog timer on PXI Embedded Controller.
Signed-off-by: Hui Chun Ong <hui.chun.ong@ni.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Declare watchdog_info structures as const as they are only stored in the
info field of watchdog_device structures. This field is of type const
struct watchdog_info *, so watchdog_info structures having this property
can be declared const too.
Done using Coccinelle:
@r1 disable optional_qualifier@
identifier i;
position p;
@@
static struct watchdog_info i@p={...};
@ok@
identifier r1.i;
position p;
struct watchdog_device obj;
@@
obj.info=&i@p;
@bad@
position p!={r1.p,ok.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct watchdog_info i;
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The object ident of type watchdog_info structure is not
modified after getting initialized by pikawdt_init. Apart from getting
referenced in init it is also passed as an argument to the function
copy_to_user but this argument is of type const void *. Therefore add
__ro_after_init to its declaration.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The object booke_wdt_info of watchdog_info structure is not
modified after getting initialized by booke_wdt_init. Apart from getting
referenced in init it is also stored in the info field of watchdog_device
structure which is of type const struct watchdog_info *info. So, it
becomes read only after init and therefore add __ro_after_init to it's
declaration.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The change corrects release of captured resources on error path, namely
the clock is disabled and put if misc device registration fails and not
enabled clock is not disabled now.
Fixes: 6924089c48 ("watchdog: sa11x0/pxa: get rid of get_clock_tick_rate")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch updates my email address as I no longer have access to the old
one.
Signed-off-by: John Crispin <john@phrozen.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
New driver for Add Loongson1 SoC.
Minor cleanup and fixes in various drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iGOO
-----END PGP SIGNATURE-----
Merge tag 'watchdog-for-linus-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull watchdog updates from Wim Van Sebroeck and Guenter Roeck:
- new driver for Add Loongson1 SoC
- minor cleanup and fixes in various drivers
* tag 'watchdog-for-linus-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
watchdog: it87_wdt: add IT8620E ID
watchdog: mpc8xxx: Remove unneeded linux/miscdevice.h include
watchdog: octeon: Remove unneeded linux/miscdevice.h include
watchdog: bcm2835_wdt: set WDOG_HW_RUNNING bit when appropriate
watchdog: loongson1: Add Loongson1 SoC watchdog driver
watchdog: cpwd: remove memory allocate failure message
watchdog: da9062/61: watchdog driver
intel-mid_wdt: Error code is just an integer
intel-mid_wdt: make sure watchdog is not running at startup
watchdog: mei_wdt: request stop on reboot to prevent false positive event
watchdog: hpwdt: changed maintainer information
watchdog: jz4740: Fix modular build
watchdog: qcom: fix kernel panic due to external abort on non-linefetch
watchdog: davinci: add support for deferred probing
watchdog: meson: Remove unneeded platform MODULE_ALIAS
watchdog: Standardize leading tabs and spaces in Kconfig file
watchdog: max77620_wdt: fix module autoload
watchdog: bcm7038_wdt: fix module autoload
This adds IT8620E chip ID to it87_wdt driver.
Such chip is often found on current Gigabyte motherboards, it is allegedly
custom made for this manufacturer.
Upon testing it looks like it has a 16-bit timer and cannot be reset via
game port (only via CIR), so it is similar to IT87{18,20,21,28,83} chips.
Tested on GA-F2A88XM-HD3P board.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
watchdog/mpc8xxx_wdt.c does not use any miscdevice so this patch remove
this unnecessary inclusion.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
watchdog/octeon-wdt-main.c does not use any miscdevice so this patch
remove this unnecessary inclusion.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A bootloader may start the watchdog device before handing control to
the kernel - in that case, we should tell the kernel about it so the
watchdog framework can keep it alive until userspace opens
/dev/watchdog0.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Replaced goto with a return statement and dropped the kfree()
calls because memory allocated with devm_kzalloc() is
automatically freed on driver detach
Signed-off-by: Amit Kushwaha <akkushwaha9896@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The of_device_id match array is added to support "dlg,da9062-watchdog"
as a valid .compatible string. A MODULE_DEVICE_TABLE() macro is added.
This patch assumes the use of a DA9062 fallback compatible string for the
DTS to pick up the DA9062 device driver for use with the DA9061 watchdog
hardware
Copyright header is updated to add DA9061 in its description and the module
description macro is extended to include DA9061.
Kconfig is updated to reflect support for DA9061/62.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Error code when printed is more readable if it's represented as plain decimal
integer. Otherwise user will see something like
intel_mid_wdt: Error stopping watchdog: 0xffffffed
which is not quite understandable ("Should I interpret it as a bitfield?").
Make it clear to use plaint integer specifier.
While here, move struct device *dev local variable definition to the top of
functions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Make sure that the watchdog is not running after loading
and before it is started by opening /dev/watchdog.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Systemd on reboot enables shutdown watchdog that leaves the watchdog
device open to ensure that even if power down process get stuck the
platform reboots nonetheless.
The iamt_wdt is an alarm-only watchdog and can't reboot system, but the
FW will generate an alarm event reboot was completed in time, as the
watchdog is not automatically disabled during power cycle.
So we should request stop watchdog on reboot to eliminate wrong alarm
from the FW.
Cc: <stable@vger.kernel.org>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Compiling this driver as a module causes a build error because a
semicolon is missing after MODULE_DEVICE_TABLE. Add it.
CC [M] drivers/watchdog/jz4740_wdt.o
drivers/watchdog/jz4740_wdt.c:154:1: error: expected ‘,’ or ‘;’ before ‘static’
drivers/watchdog/jz4740_wdt.c:218:11: error: ‘jz4740_wdt_probe’ undeclared here (not in a function)
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
devm_clk_get can fail with EPROBE_DEFER in case the clock provider is
not ready yet. Handle this case gracefully, rather than dumping out
a huge warning.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The Amlogic Meson is a DT-only platform, which means the devices are
registered via OF and not using the legacy platform devices support.
So there's no need to have a MODULE_ALIAS("platform:meson-gxbb-wdt")
since the reported uevent MODALIAS to user-space will be the OF one.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Replace small number of lines using leading spaces with proper leading
tabs and spaces -- purely an aesthetic fix.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ $ modinfo drivers/watchdog/max77620_wdt.ko | grep alias
$
After this patch:
modinfo drivers/watchdog/max77620_wdt.ko | grep alias
alias: platform:max77620-watchdog
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/watchdog/bcm7038_wdt.ko | grep alias
$
After this patch:
$ modinfo drivers/watchdog/bcm7038_wdt.ko | grep alias
alias: of:N*T*Cbrcm,bcm7038-wdtC*
alias: of:N*T*Cbrcm,bcm7038-wdt
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These are updates for platform specific code on 32-bit ARM machines,
essentially anything that can not (yet) be expressed using DT files.
Noteworthy changes include:
- Added support for the TI DRA71x family of SoCs in mach-omap2,
this is an new variant of the the DRA72x/DRA74x automotive
infotainment chips we already supported for a while.
- Added support for the ST STM32F746 SoC, the first Cortex-M7
based microcontroller we support, related to the smaller
STM32F4 family.
- Renesas adds support for r8a7743 and r8a7745 in mach-shmobile,
see http://elinux.org/RZ-G
- SMP is now supported on the OX820 platform
- A lot of code in mach-omap2 gets removed as a follow-up to
removing support for board files in the previous release
- Davinci has some new work to improve USB support
- For i.MX, the performance monitor now supports profiling the
memory controller using 'perf'
Conflicts:
arch/arm/mach-shmobile/setup-rcar-gen2.c: rcar_gen2_clocks_init()
is gone, calling of_clk_init(NULL) is sufficient now.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BF6Y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"These are updates for platform specific code on 32-bit ARM machines,
essentially anything that can not (yet) be expressed using DT files.
Noteworthy changes include:
- Added support for the TI DRA71x family of SoCs in mach-omap2, this
is an new variant of the the DRA72x/DRA74x automotive infotainment
chips we already supported for a while.
- Added support for the ST STM32F746 SoC, the first Cortex-M7 based
microcontroller we support, related to the smaller STM32F4 family.
- Renesas adds support for r8a7743 and r8a7745 in mach-shmobile, see
http://elinux.org/RZ-G
- SMP is now supported on the OX820 platform
- A lot of code in mach-omap2 gets removed as a follow-up to removing
support for board files in the previous release
- Davinci has some new work to improve USB support
- For i.MX, the performance monitor now supports profiling the memory
controller using 'perf'"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (95 commits)
ARM: davinci: da830-evm: use gpio descriptor for mmc pins
ARM: davinci: da850-evm: use gpio descriptor for mmc pins
ARM: davinci: hawk: use gpio descriptor for mmc pins
ARM: ARTPEC-6: add select MFD_SYSCON to MACH_ARTPEC6
ARM: davinci: da8xx: Fix ohci device name
ARM: oxnas: Add OX820 config and makefile entry
ARM: oxnas: Add OX820 SMP support
ARM: davinci: PM: fix build when da850 not compiled in
ARM: orion5x: remove legacy support of ls-chl
ARM: integrator: drop EBI access use syscon
ARM: BCM5301X: Add back handler ignoring external imprecise aborts
ARM: davinci: PM: support da8xx DT platforms
ARM: davinci: PM: cleanup: remove references to pdata
ARM: davinci: PM: rework init, remove platform device
ARM: Kconfig: Introduce MACH_STM32F746 flag
ARM: mach-stm32: Add a new SOC - STM32F746
ARM: shmobile: document SK-RZG1E board
ARM: shmobile: r8a7745: basic SoC support
ARM: imx: mach-imx6ul: add imx6ull support
ARM: zynq: Reserve correct amount of non-DMA RAM
...
Here's the big char/misc driver patches for 4.10-rc1. Lots of tiny
changes over lots of "minor" driver subsystems, the largest being some
new FPGA drivers. Other than that, a few other new drivers, but no new
driver subsystems added for this kernel cycle, a nice change.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWFAtwA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykyCgCeJn36u1AsBi7qZ3u/1hwD8k56s2IAnRo6U31r
WW65YcNTK7qYXqNbfgIa
=/t/V
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the big char/misc driver patches for 4.10-rc1. Lots of tiny
changes over lots of "minor" driver subsystems, the largest being some
new FPGA drivers. Other than that, a few other new drivers, but no new
driver subsystems added for this kernel cycle, a nice change.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (107 commits)
uio-hv-generic: store physical addresses instead of virtual
Tools: hv: kvp: configurable external scripts path
uio-hv-generic: new userspace i/o driver for VMBus
vmbus: add support for dynamic device id's
hv: change clockevents unbind tactics
hv: acquire vmbus_connection.channel_mutex in vmbus_free_channels()
hyperv: Fix spelling of HV_UNKOWN
mei: bus: enable non-blocking RX
mei: fix the back to back interrupt handling
mei: synchronize irq before initiating a reset.
VME: Remove shutdown entry from vme_driver
auxdisplay: ht16k33: select framebuffer helper modules
MAINTAINERS: add git url for fpga
fpga: Clarify how write_init works streaming modes
fpga zynq: Fix incorrect ISR state on bootup
fpga zynq: Remove priv->dev
fpga zynq: Add missing \n to messages
fpga: Add COMPILE_TEST to all drivers
uio: pruss: add clk_disable()
char/pcmcia: add some error checking in scr24x_read()
...
Pull smp hotplug updates from Thomas Gleixner:
"This is the final round of converting the notifier mess to the state
machine. The removal of the notifiers and the related infrastructure
will happen around rc1, as there are conversions outstanding in other
trees.
The whole exercise removed about 2000 lines of code in total and in
course of the conversion several dozen bugs got fixed. The new
mechanism allows to test almost every hotplug step standalone, so
usage sites can exercise all transitions extensively.
There is more room for improvement, like integrating all the
pointlessly different architecture mechanisms of synchronizing,
setting cpus online etc into the core code"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (60 commits)
tracing/rb: Init the CPU mask on allocation
soc/fsl/qbman: Convert to hotplug state machine
soc/fsl/qbman: Convert to hotplug state machine
zram: Convert to hotplug state machine
KVM/PPC/Book3S HV: Convert to hotplug state machine
arm64/cpuinfo: Convert to hotplug state machine
arm64/cpuinfo: Make hotplug notifier symmetric
mm/compaction: Convert to hotplug state machine
iommu/vt-d: Convert to hotplug state machine
mm/zswap: Convert pool to hotplug state machine
mm/zswap: Convert dst-mem to hotplug state machine
mm/zsmalloc: Convert to hotplug state machine
mm/vmstat: Convert to hotplug state machine
mm/vmstat: Avoid on each online CPU loops
mm/vmstat: Drop get_online_cpus() from init_cpu_node_state/vmstat_cpu_dead()
tracing/rb: Convert to hotplug state machine
oprofile/nmi timer: Convert to hotplug state machine
net/iucv: Use explicit clean up labels in iucv_init()
x86/pci/amd-bus: Convert to hotplug state machine
x86/oprofile/nmi: Convert to hotplug state machine
...
The WDAT watchdog driver uses functionality provided by the watchdog timer
core but it did not select it explicitly. This results following linker
error when only WDAT_WDT is enabled in Kconfig:
drivers/built-in.o: In function `wdat_wdt_probe':
drivers/watchdog/wdat_wdt.c:444: undefined reference to `devm_watchdog_register_device'
Fix this by explicitly selecting WATCHDOG_CORE when WDAT watchdog driver is
enabled.
Fixes: 058dfc7670 (ACPI / watchdog: Add support for WDAT hardware watchdog)
Reported-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This cycle is covering :
- some clock fixes common with sa1100 architecture
- the consequence of the pxa_camera conversion to v4l2
- a small irq related fix for pxa25x device-tree only
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1WrE
-----END PGP SIGNATURE-----
Merge tag 'pxa-for-4.10' of https://github.com/rjarzmik/linux into next/soc
This is the pxa changes for v4.10 cycle.
This cycle is covering :
- some clock fixes common with sa1100 architecture
- the consequence of the pxa_camera conversion to v4l2
- a small irq related fix for pxa25x device-tree only
* tag 'pxa-for-4.10' of https://github.com/rjarzmik/linux:
ARM: pxa: fix pxa25x interrupt init
ARM: pxa: remove duplicated include from spitz.c
ARM: pxa: em-x270: use the new pxa_camera platform_data
ARM: pxa: ezx: use the new pxa_camera platform_data
ARM: pxa: mioa701: use the new pxa_camera platform_data
ARM: pxa: pxa_cplds: honor probe deferral
ARM: sa11x0/pxa: get rid of get_clock_tick_rate
watchdog: sa11x0/pxa: get rid of get_clock_tick_rate
ARM: sa11x0/pxa: acquire timer rate from the clock rate
clk: pxa25x: OSTIMER0 clocks from the main oscillator
Signed-off-by: Olof Johansson <olof@lixom.net>
Split callbacks for RX and async notification events on mei bus to
eliminate synchronization problems and to open way for RX optimizations.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The callback context is redunant as all the information can be
retrived from the device struture of its private data.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It turns out we need to ping the watchdog hardware on resume when we
re-program it. Otherwise this causes inadvertent reset to trigger
right after the resume is complete.
Fixes: 058dfc7670 (ACPI / watchdog: Add support for WDAT hardware watchdog)
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The OS timer rate used for the watchdog can now be fetched from the
standard clock API. This will remove the last user of
get_clock_tick_rate() in both pxa and sa11x0 architectures.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Pull watchdog updates from Wim Van Sebroeck:
- a new watchdog pretimeout governor framework
- support to upload the firmware on the ziirave_wdt
- several fixes and cleanups
* git://www.linux-watchdog.org/linux-watchdog: (26 commits)
watchdog: imx2_wdt: add pretimeout function support
watchdog: softdog: implement pretimeout support
watchdog: pretimeout: add pretimeout_available_governors attribute
watchdog: pretimeout: add option to select a pretimeout governor in runtime
watchdog: pretimeout: add panic pretimeout governor
watchdog: pretimeout: add noop pretimeout governor
watchdog: add watchdog pretimeout governor framework
watchdog: hpwdt: add support for iLO5
fs: compat_ioctl: add pretimeout functions for watchdogs
watchdog: add pretimeout support to the core
watchdog: imx2_wdt: use preferred BIT macro instead of open coded values
watchdog: st_wdt: Remove support for obsolete platforms
watchdog: bindings: Remove obsolete platforms from dt doc.
watchdog: mt7621_wdt: Remove assignment of dev pointer
watchdog: rt2880_wdt: Remove assignment of dev pointer
watchdog: constify watchdog_ops structures
watchdog: tegra: constify watchdog_ops structures
watchdog: iTCO_wdt: constify iTCO_wdt_pm structure
watchdog: cadence_wdt: Fix the suspend resume
watchdog: txx9wdt: Add missing clock (un)prepare calls for CCF
...
Pull uaccess.h prepwork from Al Viro:
"Preparations to tree-wide switch to use of linux/uaccess.h (which,
obviously, will allow to start unifying stuff for real). The last step
there, ie
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
`git grep -l "$PATT"|grep -v ^include/linux/uaccess.h`
is not taken here - I would prefer to do it once just before or just
after -rc1. However, everything should be ready for it"
* 'work.uaccess2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
remove a stray reference to asm/uaccess.h in docs
sparc64: separate extable_64.h, switch elf_64.h to it
score: separate extable.h, switch module.h to it
mips: separate extable.h, switch module.h to it
x86: separate extable.h, switch sections.h to it
remove stray include of asm/uaccess.h from cacheflush.h
mn10300: remove a bogus processor.h->uaccess.h include
xtensa: split uaccess.h into C and asm sides
bonding: quit messing with IOCTL
kill __kernel_ds_p off
mn10300: finish verify_area() off
frv: move HAVE_ARCH_UNMAPPED_AREA to pgtable.h
exceptions: detritus removal
The change adds watchdog pretimeout notification handling to imx2_wdt
driver, if device data contains information about a valid interrupt.
It is unlikely but still possible (e.g. through a software limitation)
that only a subset of watchdogs on SoC has interrupt lines, hence
functionally the devices from these two groups have different
capabilities, and this is reflected in different watchdog_info
structs assigned to the devices.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Give devices which do not have hardware support for pretimeout at least a
software version of it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The change adds an option to a user with CONFIG_WATCHDOG_SYSFS and
CONFIG_WATCHDOG_PRETIMEOUT_GOV enabled to get information about all
registered watchdog pretimeout governors by reading watchdog device
attribute named "pretimeout_available_governors".
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The change converts watchdog device attribute "pretimeout_governor" from
read-only to read-write type to allow users to select a desirable
watchdog pretimeout governor in runtime, e.g.
% echo -n panic > /sys/..../watchdog/watchdog0/pretimeout
To get this working a list of registered pretimeout governors is created
and a new helper function watchdog_pretimeout_governor_set() is exported
to watchdog_dev.c.
If a selected governor is gone, a watchdog device pretimeout notification
is delegated to a default built-in pretimeout governor.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The change adds panic watchdog pretimeout governor, on watchdog
pretimeout event the kernel shall panic. In general watchdog
pretimeout event means that something essentially bad is going on the
system, for example a process scheduler stalls or watchdog feeder is
killed due to OOM, so printing out information attendant to panic and
before likely unavoidable reboot caused by a watchdog may help to
determine a root cause of the issue.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The change adds noop watchdog pretimeout governor, only an
informational message is printed to the kernel log buffer when a
watchdog triggers a pretimeout event.
While introducing the first pretimeout governor the selected design
assumes that the default pretimeout governor is selected by its name
and it is always built-in, thus the default pretimeout governor can
not be unregistered and the correspondent check can be removed from
the watchdog_unregister_governor() function.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The change adds a simple watchdog pretimeout framework infrastructure,
its purpose is to allow users to select a desired handling of watchdog
pretimeout events, which may be generated by some watchdog devices.
A user selects a default watchdog pretimeout governor during
compilation stage.
Watchdogs with WDIOF_PRETIMEOUT capability now have one more device
attribute in sysfs, pretimeout_governor attribute is intended to display
the selected watchdog pretimeout governor.
The framework has no impact at runtime on watchdog devices with no
WDIOF_PRETIMEOUT capability set.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
more victims of indirect include chains - au1200fb
lasat/picvue_proc and watchdog/ath79_wdt
... as well as tb0219, spotted by Sudip Mukherjee
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Here is the big USB, and PHY, and extcon, patchsets for 4.9-rc1.
Full details are in the shortlog, but generally a lot of new hardware
support, usb gadget updates, and Wolfram's great cleanup of USB error
message handling, making the kernel image a tad bit smaller.
All of this has been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlfyNTEPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspbuUAoJAn
XD6k9A+0QgnJ/iLiT8pztawNAKCCVYZOzgdFRGsnaZ2p7lb9IHpPCA==
=QUj+
-----END PGP SIGNATURE-----
Merge tag 'usb-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull usb/phy/extcon updates from Greg KH:
"Here is the big USB, and PHY, and extcon, patchsets for 4.9-rc1.
Full details are in the shortlog, but generally a lot of new hardware
support, usb gadget updates, and Wolfram's great cleanup of USB error
message handling, making the kernel image a tad bit smaller.
All of this has been in linux-next with no reported issues"
* tag 'usb-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (343 commits)
Revert "usbtmc: convert to devm_kzalloc"
USB: serial: cp210x: Add ID for a Juniper console
usb: Kconfig: using select for USB_COMMON dependency
bluetooth: bcm203x: don't print error when allocating urb fails
mmc: host: vub300: don't print error when allocating urb fails
usb: hub: change CLEAR_FEATURE to SET_FEATURE
usb: core: Introduce a USB port LED trigger
USB: bcma: drop Northstar PHY 2.0 initialization code
usb: core: hcd: add missing header dependencies
usb: musb: da8xx: fix error handling message in probe
usb: musb: Fix session based PM for first invalid VBUS
usb: musb: Fix PM runtime for disconnect after unconfigure
musb: Export musb_root_disconnect for use in modules
usb: misc: legousbtower: Fix NULL pointer deference
cdc-acm: hardening against malicious devices
Revert "usb: gadget: NCM: Protect dev->port_usb using dev->lock"
include: extcon: Fix compilation error caused because of incomplete merge
MAINTAINERS: add tree entry for USB Serial
phy-twl4030-usb: initialize charging-related stuff via pm_runtime
phy-twl4030-usb: better handle musb_mailbox() failure
...
iLO5 will offer the same watchdog timer as previous generations, but the
PCI subsystem vendor ID will be PCI_VENDOR_ID_HP_3PAR (0x1590) instead of
PCI_VENDOR_ID_HP (0x103c). Add 0x1590 to the whitelist and be more
specific when ignoring the 103c,1979 device.
Signed-off-by: Brian Boylston <brian.boylston@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Fixes the following sparse warnings:
drivers/watchdog/wdat_wdt.c:210:66: warning: Using plain integer as NULL pointer
drivers/watchdog/wdat_wdt.c:235:66: warning: Using plain integer as NULL pointer
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since the watchdog framework centrializes the IOCTL interfaces of device
drivers now, SETPRETIMEOUT and GETPRETIMEOUT need to be added in the
common code.
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
[vzapolskiy: added conditional pretimeout sysfs attribute visibility]
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This is a nonfunctional change, declare register bit values with BIT()
helper macro.
The issues are reported by checkpatch:
CHECK: Prefer using the BIT macro
#40: FILE: drivers/watchdog/imx2_wdt.c:40:
+#define IMX2_WDT_WCR_WDA (1 << 5) /* -> External Reset WDOG_B */
etc.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
STiH415/6 SoC support is being removed from the kernel.
This patch updates the watchdog driver to remove references
to these obsolete platforms.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: <linux-watchdog@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Commit 0254e95353 ("watchdog: Drop pointer to watchdog device from
struct watchdog_device") removed the dev pointer from struct
watchdog_device, but this driver was still assigning it, leading to
a compilation error:
drivers/watchdog/mt7621_wdt.c: In function 'mt7621_wdt_probe':
drivers/watchdog/mt7621_wdt.c:142:16: error:
'struct watchdog_device' has no member named 'dev'
Fix this by removing the assignment.
Fixes: 0254e95353 ("watchdog: Drop pointer to watchdog device ...")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org # v4.5+
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Commit 0254e95353 ("watchdog: Drop pointer to watchdog device from
struct watchdog_device") removed the dev pointer from struct
watchdog_device, but this driver was still assigning it, leading to a
compilation error:
drivers/watchdog/rt2880_wdt.c: In function ‘rt288x_wdt_probe’:
drivers/watchdog/rt2880_wdt.c:161:16: error: ‘struct watchdog_device’
has no member named ‘dev’
rt288x_wdt_dev.dev = &pdev->dev;
^
scripts/Makefile.build:289: recipe for target
'drivers/watchdog/rt2880_wdt.o' failed
Fix this by removing the assignment.
Fixes: 0254e95353 ("watchdog: Drop pointer to watchdog device ...")
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: stable@vger.kernel.org # v4.5+
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Check for watchdog_ops structures that are only stored in the ops field of
a watchdog_device structure. This field is declared const, so watchdog_ops
structures that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct watchdog_ops i@p = { ... };
@ok@
identifier r.i;
struct watchdog_device e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct watchdog_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct watchdog_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Check for watchdog_ops structures that are only stored in the ops field of
a watchdog_device structure. This field is declared const, so watchdog_ops
structures that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct watchdog_ops i@p = { ... };
@ok@
identifier r.i;
struct watchdog_device e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct watchdog_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct watchdog_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
iTCO_wdt_pm, of type struct dev_pm_ops, is never modified, so declare it as
const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Currently even if no users are there the suspend tries to
stop the watchdog and resume starts it.
so after resume the watchdog starts and resets the board.
Fix the same by adding a check for users.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Starting from Intel Skylake the iTCO watchdog timer registers were moved to
reside in the same register space with SMBus host controller. Not all
needed registers are available though and we need to unhide P2SB (Primary
to Sideband) device briefly to be able to read status of required NO_REBOOT
bit. The i2c-i801.c SMBus driver used to handle this and creation of the
iTCO watchdog platform device.
Windows, on the other hand, does not use the iTCO watchdog hardware
directly even if it is available. Instead it relies on ACPI Watchdog Action
Table (WDAT) table to describe the watchdog hardware to the OS. This table
contains necessary information about the the hardware and also set of
actions which are executed by a driver as needed.
This patch implements a new watchdog driver that takes advantage of the
ACPI WDAT table. We split the functionality into two parts: first part
enumerates the WDAT table and if found, populates resources and creates
platform device for the actual driver. The second part is the driver
itself.
The reason for the split is that this way we can make the driver itself to
be a module and loaded automatically if the WDAT table is found. Otherwise
the module is not loaded.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
While the custom minimal TXx9 clock implementation doesn't need or use
clock (un)prepare calls (they are dummies if !CONFIG_HAVE_CLK_PREPARE),
they are mandatory when using the Common Clock Framework.
Hence add them, to prepare for the advent of CCF.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The field "owner" is set by core. Thus delete an extra initialisation.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds and entry to the sysfs to start firmware upload process
on the specified device with the requested firmware.
The uploading of the firmware needs only to happen once per firmware
upgrade, as the firmware is stored in persistent storage. If the
firmware upload or the firmware verification fails then we print and
error message and exit.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add support for the clock. Currently we enable
at probe and relinquish at remove.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Coverity reports:
divide_by_zero: In expression readl(dw_wdt->regs + 8) /
clk_get_rate(dw_wdt->clk), division by expression clk_get_rate(dw_wdt->clk)
which may be zero has undefined behavior.
The clock used for the watchdog timer won't change its rate, so read it
only once during probe. Also validate it and abort the probe function
with an error if it is 0.
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Coverity reports:
Passing argument 152UL /* sizeof (*wdd) */ to function __devres_alloc_node
and then casting the return value to struct watchdog_device ** is
suspicious.
Allocation size needs to be sizeof(*rcwdd), not sizeof(*wdd).
Fixes: 83fbae5a14 ("watchdog: Add a device managed API for ...")
Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WDOG_HW_RUNNING indicates that the hardware watchdog is running while the
watchdog device is closed. The flag may be set by the driver when it is
instantiated to indicate that the watchdog is running, and that the
watchdog core needs to send heartbeat requests to the driver until the
watchdog device is opened.
When the watchdog device is closed, the flag can be used by the driver's
stop function to indicate to the watchdog core that it was unable to stop
the watchdog, and that the watchdog core needs to send heartbeat requests.
This only works if the flag is actually cleared when the watchdog is
stopped. To avoid having to clear the flag in each driver's stop function,
clear it in the watchdog core before calling the stop function.
Reported-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Fixes: ee142889e3 ("watchdog: Introduce WDOG_HW_RUNNING flag")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
