Since all sub-protocols of MHL3 are already supported MHL3 mode can be
enabled. With this patch it is possible to use packed pixel modes and
clocks up to 300MHz - 1920x1080@60Hz and 4K modes.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-25-git-send-email-a.hajda@samsung.com
MHL3 protocol requires registry adjustments depending on chosen video mode.
Necessary information is gathered in mode_fixup callback. In case of HDMI
video modes driver should also send special AVI and MHL3 infoframes.
The patch introduces generic helpers for handling MHL3 infoframes, in
case of appearance of other users of MHL3 infoframes these function can
be moved to common library.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-21-git-send-email-a.hajda@samsung.com
The Single-ended eCBUS Mode (eCBUS-S) mode provides 60 Mb/s full-duplex
bidirectional traffic for three channels:
- CBUS data (CBUS1 channel),
- High-bandwidth MHL data (eMSC channel),
- tunneling data (T-CBUS channel).
It is required to fully support MHL3 dongles.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-6-git-send-email-a.hajda@samsung.com
Due to asynchronous nature of MHL flow of execution is dispersed.
Logical continuation of some actions happens after response of peer,
i.e in interrupt handler. To simplify coding continuation mechanism
has been added - it is now possible to provide continuation callback,
which will be called after peer responds to given action.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-5-git-send-email-a.hajda@samsung.com
Another round of -misc stuff:
- Noralf debugfs cleanup cleanup (not yet everything, some more driver
patches awaiting acks).
- More doc work.
- edid/infoframe fixes from Ville.
- misc 1-patch fixes all over, as usual
Noralf needs this for his tinydrm pull request.
* tag 'drm-misc-next-2017-01-30' of git://anongit.freedesktop.org/git/drm-misc: (48 commits)
drm/vc4: Remove vc4_debugfs_cleanup()
dma/fence: Export enable-signaling tracepoint for emission by drivers
drm/tilcdc: Remove tilcdc_debugfs_cleanup()
drm/tegra: Remove tegra_debugfs_cleanup()
drm/sti: Remove drm_debugfs_remove_files() calls
drm/radeon: Remove drm_debugfs_remove_files() call
drm/omap: Remove omap_debugfs_cleanup()
drm/hdlcd: Remove hdlcd_debugfs_cleanup()
drm/etnaviv: Remove etnaviv_debugfs_cleanup()
drm/etnaviv: allow build with COMPILE_TEST
drm/amd/amdgpu: Remove drm_debugfs_remove_files() call
drm/prime: Clarify DMA-BUF/GEM Object lifetime
drm/ttm: Make sure BOs being swapped out are cacheable
drm/atomic: Remove drm_atomic_debugfs_cleanup()
drm: drm_minor_register(): Clean up debugfs on failure
drm: debugfs: Remove all files automatically on cleanup
drm/fourcc: add vivante tiled layout format modifiers
drm/edid: Set YQ bits in the AVI infoframe according to CEA-861-F
drm/edid: Set AVI infoframe Q even when QS=0
drm/edid: Introduce drm_hdmi_avi_infoframe_quant_range()
...
- cleanups&fixes for dw-hdmi bride driver (Laurent)
- updates for adv bridge driver (John Stultz) for nexus
- drm_crtc_from_index helper rollout (Shawn Guo)
- removing drm_framebuffer_unregister_private from drivers&core
- target_vblank (Andrey Grodzovsky)
- misc tiny stuff
* tag 'drm-misc-next-2017-01-23' of git://anongit.freedesktop.org/git/drm-misc: (49 commits)
drm: qxl: Open code teardown function for qxl
drm: qxl: Open code probing sequence for qxl
drm/bridge: adv7511: Re-write the i2c address before EDID probing
drm/bridge: adv7511: Reuse __adv7511_power_on/off() when probing EDID
drm/bridge: adv7511: Rework adv7511_power_on/off() so they can be reused internally
drm/bridge: adv7511: Enable HPD interrupts to support hotplug and improve monitor detection
drm/bridge: adv7511: Switch to using drm_kms_helper_hotplug_event()
drm/bridge: adv7511: Use work_struct to defer hotplug handing to out of irq context
drm: vc4: use crtc helper drm_crtc_from_index()
drm: tegra: use crtc helper drm_crtc_from_index()
drm: nouveau: use crtc helper drm_crtc_from_index()
drm: mediatek: use crtc helper drm_crtc_from_index()
drm: kirin: use crtc helper drm_crtc_from_index()
drm: exynos: use crtc helper drm_crtc_from_index()
dt-bindings: display: dw-hdmi: Clean up DT bindings documentation
drm: bridge: dw-hdmi: Assert SVSRET before resetting the PHY
drm: bridge: dw-hdmi: Fix the name of the PHY reset macros
drm: bridge: dw-hdmi: Define and use macros for PHY register addresses
drm: bridge: dw-hdmi: Detect PHY type at runtime
drm: bridge: dw-hdmi: Handle overflow workaround based on device version
...
Backmerge Linus master to get the connector locking revert.
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux: (645 commits)
sysctl: fix proc_doulongvec_ms_jiffies_minmax()
Revert "drm/probe-helpers: Drop locking from poll_enable"
MAINTAINERS: add Dan Streetman to zbud maintainers
MAINTAINERS: add Dan Streetman to zswap maintainers
mm: do not export ioremap_page_range symbol for external module
mn10300: fix build error of missing fpu_save()
romfs: use different way to generate fsid for BLOCK or MTD
frv: add missing atomic64 operations
mm, page_alloc: fix premature OOM when racing with cpuset mems update
mm, page_alloc: move cpuset seqcount checking to slowpath
mm, page_alloc: fix fast-path race with cpuset update or removal
mm, page_alloc: fix check for NULL preferred_zone
kernel/panic.c: add missing \n
fbdev: color map copying bounds checking
frv: add atomic64_add_unless()
mm/mempolicy.c: do not put mempolicy before using its nodemask
radix-tree: fix private list warnings
Documentation/filesystems/proc.txt: add VmPin
mm, memcg: do not retry precharge charges
proc: add a schedule point in proc_pid_readdir()
...
The of_node member in struct drm_bridge is hidden when CONFIG_OF
is disabled, causing a build error:
drivers/gpu/drm/bridge/dw-hdmi.c: In function '__dw_hdmi_probe':
drivers/gpu/drm/bridge/dw-hdmi.c:2063:14: error: 'struct drm_bridge' has no member named 'of_node'
We could fix this either using a Kconfig dependency on CONFIG_OF
or making the one line conditional. The latter gives us better
compile test coverage, so this is what I'm doing here.
Fixes: 69497eb923 ("drm: bridge: dw-hdmi: Implement DRM bridge registration")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170123122312.3290934-1-arnd@arndb.de
I've found that by just turning the chip on and off via the
POWER_DOWN register, I end up getting i2c_transfer errors on
HiKey.
Investigating further, it turns out that some of the register
state in hardware is getting lost, as the device registers are
reset when the chip is powered down.
Thus this patch simply re-writes the i2c address to the
ADV7511_REG_EDID_I2C_ADDR register to ensure its properly set
before we try to read the EDID data.
Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1484614372-15342-7-git-send-email-john.stultz@linaro.org
Thus this patch changes the EDID probing logic so that we
re-use the __adv7511_power_on/off() calls instead of duplciating
logic.
This does change behavior slightly as it adds the HPD signal
pulse to the EDID probe path, but Archit has had a patch to
add HPD signal pulse to the EDID probe path before, so this
should address the cases where that helped. Another difference
is that regcache_mark_dirty() is also called in the power off
path once EDID is probed.
Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1484614372-15342-6-git-send-email-john.stultz@linaro.org
In chasing down issues with EDID probing, I found some
duplicated but incomplete logic used to power the chip on and
off.
This patch refactors the adv7511_power_on/off functions, so
they can be used for internal needs.
Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1484614372-15342-5-git-send-email-john.stultz@linaro.org
On some adv7511 implementations, we can get some spurious
disconnect signals which can cause monitor probing to fail.
This patch enables HPD (hot plug detect) interrupt support
which allows the monitor to be properly re-initialized when
the spurious disconnect signal goes away.
This also enables proper hotplug support.
Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Originally-by: Archit Taneja <architt@codeaurora.org>
[jstultz: Added proper commit message]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1484614372-15342-4-git-send-email-john.stultz@linaro.org
In chasing down a previous issue with EDID probing from calling
drm_helper_hpd_irq_event() from irq context, Laurent noticed
that the DRM documentation suggests that
drm_kms_helper_hotplug_event() should be used instead.
Thus this patch replaces drm_helper_hpd_irq_event() with
drm_kms_helper_hotplug_event(), which requires we update the
connector.status entry and only call _hotplug_event() when the
status changes.
Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1484614372-15342-3-git-send-email-john.stultz@linaro.org
I was recently seeing issues with EDID probing, where
the logic to wait for the EDID read bit to be set by the
IRQ wasn't happening and the code would time out and fail.
Digging deeper, I found this was due to the fact that
IRQs were disabled as we were running in IRQ context from
the HPD signal.
Thus this patch changes the logic to handle the HPD signal
via a work_struct so we can be out of irq context.
With this patch, the EDID probing on hotplug does not time
out.
Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1484614372-15342-2-git-send-email-john.stultz@linaro.org
According to the PHY IP core vendor, the SVSRET signal must be asserted
before resetting the PHY. Tests on RK3288 and R-Car Gen3 showed no
regression, the change should thus be safe.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-20-laurent.pinchart+renesas@ideasonboard.com
The PHY reset signal is controlled by bit PHYRSTZ in the MC_PHYRSTZ
register. The signal is active low on Gen1 PHYs and active high on Gen2
PHYs. The driver toggles the signal high then low, which is correct for
all currently supported platforms, but the register values macros are
incorrectly named. Replace them with a single macro named after the bit,
and add a comment to the source code to explain the behaviour.
The driver's behaviour isn't changed by this rename, the code will still
need to be fixed to support Gen1 PHYs.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-19-laurent.pinchart+renesas@ideasonboard.com
Replace the hardcoded register address numerical values with macros to
clarify the code.
This change has been tested by comparing the assembly code before and
after the change.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-18-laurent.pinchart+renesas@ideasonboard.com
Use the device version queried at runtime instead of the device type
provided through platform data to handle the overflow workaround. This
will make support of other SoCs integrating the same HDMI TX controller
version easier.
Among the supported platforms only i.MX6DL and i.MX6Q have been
identified as needing the workaround. Disabling it on Rockchip RK3288
(which integrates a v2.00a controller) didn't produce any error or
artifact.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-16-laurent.pinchart+renesas@ideasonboard.com
Bit 0 in CONFIG1_ID tells whether the IP core uses an AHB slave
interface for control. The correct way to identify AHB audio DMA support
is through bit 1 in CONFIG3_ID.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-15-laurent.pinchart+renesas@ideasonboard.com
The DWC HDMI TX can be recognized by the two product identification
registers. If the registers don't read as expect the IP will be very
different than what the driver has been designed for, or will be
misconfigured in a way that makes it non-operational (invalid memory
address, incorrect clocks, ...). We should reject this situation with an
error.
While this isn't critical for proper operation with supported IPs at the
moment, the driver will soon gain automatic device-specific handling
based on runtime device identification. This change makes it easier to
implement that without having to default to a random guess in case the
device can't be identified.
While at it print a readable version number in the device identification
message instead of raw register values.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-14-laurent.pinchart+renesas@ideasonboard.com
The bit is documented in a Rockchip BSP as
#define m_SVSRET_SIG (1 << 5) /* depend on PHY_MHL_COMB0=1 */
This is confirmed by a Renesas platform, which uses a 2.0 DWC HDMI TX as
the RK3288. Rename the bit accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-13-laurent.pinchart+renesas@ideasonboard.com
The current code hard codes the call of hdmi_phy_configure() to be 8bpp
and provides extraneous error checking to verify that this hardcoded
value is correct. Simplify the implementation by removing the argument.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-12-laurent.pinchart+renesas@ideasonboard.com
As an option for drivers not based on the component framework, register
the bridge with the DRM core with the DRM bridge API. Existing drivers
based on dw_hdmi_bind() and dw_hdmi_unbind() are not affected as those
functions are preserved with their current behaviour.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-11-laurent.pinchart+renesas@ideasonboard.com
The DRM device is not guaranteed by the bridge API to be available
before the attach callback. The driver performs properly at the moment
as it doesn't use the drm_bridge_add() registration method. As this will
be changed later, move connector creation to attach time to ensure
compatibility with the API.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-10-laurent.pinchart+renesas@ideasonboard.com
The next commit will reference structures and functions in a way that
currently requires forward declarations. Reorder the functions to avoid
that. No functional change to the code is performed.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-9-laurent.pinchart+renesas@ideasonboard.com
There's no need to duplicate identical code in multiple drivers (two at
the moment, one more to come soon). Move it to the dw-hdmi core where it
can be shared. If resource allocation ever becomes device-specific later
we'll always have the option of splitting it out again.
While it at pass the platform device to the bind function to avoid
having to cast struct device to struct platform_device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-8-laurent.pinchart+renesas@ideasonboard.com
Hotplug events should only be forwarded to the DRM core by the interrupt
handler when the bridge has been attached, otherwise the DRM device
pointer will be NULL, resulting in a crash.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-7-laurent.pinchart+renesas@ideasonboard.com
The 'prep' parameter passed to hdmi_phy_configure() is useless. It is
hardcoded as 0, and if set, simply prevents the configure function from
executing.
Remove it.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-4-laurent.pinchart+renesas@ideasonboard.com
The master argument isn't used. The data argument, a void pointer, is
used by the bind function only where it's cast to a drm_device pointer,
which can easily be obtained from the encoder argument instead. Remove
them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-3-laurent.pinchart+renesas@ideasonboard.com
The latter is just an int wrapper around the former void function that
unconditionally returns 0. As the return value is never checked, merge
the two functions into one.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-2-laurent.pinchart+renesas@ideasonboard.com
Maintain a table of regulator names expected by ADV7511 and ADV7533.
Use regulator_bulk_* api to configure these.
Initialize and enable the regulators during probe itself. Controlling
these dynamically is left for later.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1484117547-26417-3-git-send-email-architt@codeaurora.org
Analogix_dp_bind() can be called from component framework, which doesn't
guarantee proper runtime PM state of the device during bind operation,
so ensure that device is runtime active before doing any register access.
This ensures that the power domain, to which DP module belongs, is turned
on. While at it, also fix the unbalanced call to phy_power_on() in
analogix_dp_bind() function.
This patch solves the following kernel oops on Samsung Exynos5250 Snow
board:
Unhandled fault: imprecise external abort (0x406) at 0x00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: : 406 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 75 Comm: kworker/0:2 Not tainted 4.9.0 #1046
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
Workqueue: events deferred_probe_work_func
task: ee272300 task.stack: ee312000
PC is at analogix_dp_enable_sw_function+0x18/0x2c
LR is at analogix_dp_init_dp+0x2c/0x50
...
[<c03fcb38>] (analogix_dp_enable_sw_function) from [<c03fa9c4>] (analogix_dp_init_dp+0x2c/0x50)
[<c03fa9c4>] (analogix_dp_init_dp) from [<c03fab6c>] (analogix_dp_bind+0x184/0x42c)
[<c03fab6c>] (analogix_dp_bind) from [<c03fdb84>] (component_bind_all+0xf0/0x218)
[<c03fdb84>] (component_bind_all) from [<c03ed64c>] (exynos_drm_load+0x134/0x200)
[<c03ed64c>] (exynos_drm_load) from [<c03d5058>] (drm_dev_register+0xa0/0xd0)
[<c03d5058>] (drm_dev_register) from [<c03d66b8>] (drm_platform_init+0x58/0xb0)
[<c03d66b8>] (drm_platform_init) from [<c03fe0c4>] (try_to_bring_up_master+0x14c/0x188)
[<c03fe0c4>] (try_to_bring_up_master) from [<c03fe188>] (component_add+0x88/0x138)
[<c03fe188>] (component_add) from [<c0403a38>] (platform_drv_probe+0x50/0xb0)
[<c0403a38>] (platform_drv_probe) from [<c0402470>] (driver_probe_device+0x1f0/0x2a8)
[<c0402470>] (driver_probe_device) from [<c0400a54>] (bus_for_each_drv+0x44/0x8c)
[<c0400a54>] (bus_for_each_drv) from [<c04021f8>] (__device_attach+0x9c/0x100)
[<c04021f8>] (__device_attach) from [<c04018e8>] (bus_probe_device+0x84/0x8c)
[<c04018e8>] (bus_probe_device) from [<c0401d1c>] (deferred_probe_work_func+0x60/0x8c)
[<c0401d1c>] (deferred_probe_work_func) from [<c012fc14>] (process_one_work+0x120/0x318)
[<c012fc14>] (process_one_work) from [<c012fe34>] (process_scheduled_works+0x28/0x38)
[<c012fe34>] (process_scheduled_works) from [<c0130048>] (worker_thread+0x204/0x4ac)
[<c0130048>] (worker_thread) from [<c01352c4>] (kthread+0xd8/0xf4)
[<c01352c4>] (kthread) from [<c0107978>] (ret_from_fork+0x14/0x3c)
Code: e59035f0 e5935018 f57ff04f e3c55001 (f57ff04e)
---[ end trace 3d1d0d87796de344 ]---
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1483091866-1088-1-git-send-email-m.szyprowski@samsung.com
Instead of linking encoders and bridges in every driver (and getting it
wrong half of the time, as many drivers forget to set the drm_bridge
encoder pointer), do so in core code. The drm_bridge_attach() function
needs the encoder and optional previous bridge to perform that task,
update all the callers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Stefan Agner <stefan@agner.ch> # For DCU
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> # For atmel-hlcdc
Acked-by: Vincent Abriou <vincent.abriou@st.com> # For STI
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> # For sun4i
Acked-by: Xinliang Liu <z.liuxinliang@hisilicon.com> # For hisilicon
Acked-by: Jyri Sarha <jsarha@ti.com> # For tilcdc
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1481709550-29226-4-git-send-email-laurent.pinchart+renesas@ideasonboard.com
It looks like the BOE panel FW didn't ack the DPCD600 signal from the
host device, this will cause the panel to hang on the startup display.
The root cause is that we use the fast link mode when we enter and
exit PSR, the issue is gone if we switch from the fast link to main
link mode.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1481338159-7189-1-git-send-email-wxt@rock-chips.com
THS8135 is a configurable video DAC, but no configuration is actually
necessary to make it work.
For now use the dumb-vga-dac driver to support it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1481623759-12786-4-git-send-email-bgolaszewski@baylibre.com
We will ignored PSR setting if panel not support it. So, in this case,
we should return from analogix_dp_enable/disable_psr() without any
error code. Let's retrun 0 instead of -EINVAL when panel not support PSR
in analogix_dp_enable/disable_psr().
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1481072253-8917-1-git-send-email-wzz@rock-chips.com
Backmerge v4.9-rc8 to get at
commit e94bd1736f
Author: Michel Dänzer <michel.daenzer@amd.com>
Date: Wed Nov 30 17:30:01 2016 +0900
drm: Don't call drm_for_each_crtc with a non-KMS driver
so I can apply Michel's follow-up patch.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Many drivers (21 to be exact) create connectors that are always
connected (for instance to an LVDS or DSI panel). Instead of forcing
them to implement a dummy .detect() handler, make the callback optional
and consider the connector as always connected in that case.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Vincent Abriou <vincent.abriou@st.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[seanpaul fixed small conflict in rcar-du/rcar_du_lvdscon.c]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
ASSR is an optional feature, so it's a valid operating condition for
the display to reject ASSR enable. Demote the warning to the debug
level.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by:Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20161130114810.3245-1-l.stach@pengutronix.de
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7Fpy
-----END PGP SIGNATURE-----
Merge tag 'tilcdc-4.10' of https://github.com/jsarha/linux into drm-next
tilcdc changes for v4.10
* tag 'tilcdc-4.10' of https://github.com/jsarha/linux: (23 commits)
drm/tilcdc: fix parsing of some DT properties
drm/tilcdc: Enable frame done irq and functionality for LCDC rev 1
drm/tilcdc: Configure video mode to HW in enable() not in mode_set_nofb()
drm/tilcdc: Load palette at the end of mode_set_nofb()
drm/tilcdc: Add timeout wait for palette loading to complete
drm/tilcdc: Enable palette loading for revision 2 LCDC too
drm/tilcdc: Fix load mode bit-field setting in tilcdc_crtc_enable()
drm/tilcdc: Add tilcdc_write_mask() to tilcdc_regs.h
drm/tilcdc: Fix tilcdc_crtc_create() return value handling
drm/tilcdc: implement palette loading for rev1
drm/tilcdc: Enable sync lost error and recovery handling for rev 1 LCDC
drm/tilcdc: Add drm bridge support for attaching drm bridge drivers
drm/bridge: Add ti-tfp410 DVI transmitter driver
dt-bindings: Move "ti,tfp410.txt" from display/ti to display/bridge
drm/tilcdc: Recover from sync lost error flood by resetting the LCDC
drm/tilcdc: Fix race from forced shutdown of crtc in unload
drm/tilcdc: Use unload to handle initialization failures
drm/tilcdc: Stop using struct drm_driver load() callback
drm/tilcdc: Remove obsolete drm_connector_register() calls
drm/tilcdc: Correct misspelling in error message
...
Add very basic ti-tfp410 DVI transmitter driver. The only feature
separating this from a completely dummy bridge is the EDID read
support trough DDC I2C. Even that functionality should be in a
separate generic connector driver. However, because of missing DRM
infrastructure support the connector is implemented within the bridge
driver. Some tfp410 HW specific features may be added later if needed,
because there is a set of registers behind i2c if it is connected.
This implementation is tested against my new tilcdc bridge support
and it works with BeagleBone DVI-D Cape Rev A3. A DT binding document
is also updated.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
This patch enables the Audio Data and Clock pads to the adv7533 bridge.
Without this patch audio can not be played.
Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Andy Green <andy@warmcat.com>
Cc: Dave Long <dave.long@linaro.org>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Zhangfei Gao <zhangfei.gao@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Jose Abreu <joabreu@synopsys.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1480382552-28219-3-git-send-email-john.stultz@linaro.org
This patch adds support to Audio for both adv7511 and adv7533
bridge chips.
This patch was originally from [1] by Lars-Peter Clausen <lars@metafoo.de>
and was adapted by Archit Taneja <architt@codeaurora.org> and
Srinivas Kandagatla <srinivas.kandagatla@linaro.org>.
Then I heavily reworked it to use the hdmi-codec driver. And also
folded in some audio packet initialization done by Andy Green
<andy.green@linaro.org>. So credit to them, but blame to me.
[1] https://github.com/analogdevicesinc/linux/blob/xcomm_zynq/drivers/gpu/drm/i2c/adv7511_audio.c
Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Andy Green <andy@warmcat.com>
Cc: Dave Long <dave.long@linaro.org>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Zhangfei Gao <zhangfei.gao@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Jose Abreu <joabreu@synopsys.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: dri-devel@lists.freedesktop.org
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1480382552-28219-2-git-send-email-john.stultz@linaro.org
The newly added sound driver depends on SND_SOC_HDMI_CODEC, which in
turn only makes sense when ASoC is enabled, as shown by this warning:
warning: (DRM_MSM && DRM_STI && DRM_MEDIATEK_HDMI && DRM_I2C_NXP_TDA998X && DRM_DW_HDMI_I2S_AUDIO) selects SND_SOC_HDMI_CODEC which has unmet direct dependencies (SOUND && !M68K && !UML && SND && SND_SOC)
Since the audio driver is probably useless without the audio subsystem,
adding a dependency here seems the right solution.
Fixes: 2761ba6c09 ("drm: bridge: add DesignWare HDMI I2S audio support")
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20161125205411.1157522-1-arnd@arndb.de
Current dw-hdmi is supporting sound via AHB bus, but it has
I2S audio feature too. This patch adds I2S audio support to dw-hdmi.
This HDMI I2S is supported by using ALSA SoC common HDMI encoder
driver.
Tested-by: Jose Abreu <joabreu@synopsys.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/8737j2bxba.wl%kuninori.morimoto.gx@renesas.com
Some dumb VGA DACs are active components which require external power.
Add support for specifying a regulator as its power supply.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20161116154232.872-2-wens@csie.org
Reference from drm_dp_aux description (about transfer):
Upon success, the implementation should return the number of payload bytes
that were transferred, or a negative error-code on failure. Helpers
propagate errors from the .transfer() function, with the exception of
the -EBUSY error, which causes a transaction to be retried. On a short,
helpers will return -EPROTO to make it simpler to check for failure.
The analogix_dp_transfer will return num_transferred, but if there is none
byte been transferred, the return value will be 0, which means success, we
should return error-code if transfer none byte.
for (retry = 0; retry < 32; retry++) {
err = aux->transfer(aux, &msg);
if (err < 0) {
if (err == -EBUSY)
continue;
goto unlock;
}
}
Cc: zain wang <wzz@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1479255219-7243-1-git-send-email-jay.xu@rock-chips.com
- add support for the HDMI I2C master controller, for boards that
can have their DDC pins connected only to the HDMI TX directly.
-----BEGIN PGP SIGNATURE-----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=aAzo
-----END PGP SIGNATURE-----
Merge tag 'dw-hdmi-next-2016-09-19' of git://git.pengutronix.de/git/pza/linux into drm-next
dw-hdmi i2c master controller
- add support for the HDMI I2C master controller, for boards that
can have their DDC pins connected only to the HDMI TX directly.
* tag 'dw-hdmi-next-2016-09-19' of git://git.pengutronix.de/git/pza/linux:
drm: bridge/dw_hdmi: add dw hdmi i2c bus adapter support
drm: dw_hdmi: use of_get_i2c_adapter_by_node interface
drivers/gpu/drm/bridge/sil-sii8620.c:1556:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20161026165836.GA98766@lkp-sb04.lkp.intel.com
SiI8620 transmitter converts eTMDS/HDMI signal to MHL 3.0.
It is controlled via I2C bus. Its interaction with other
devices in video pipeline is performed mainly on HW level.
The only interaction it does on device driver level is
filtering-out unsupported video modes, it exposes drm_bridge
interface to perform this operation.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1476085157-5266-1-git-send-email-a.hajda@samsung.com
Drop unneeded drm_connector_unregister() and remove the unnecessary
wrapper functions around drm_connector_cleanup().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161005143133.5549-1-marex@denx.de
Some boards have an entirely passive RGB to VGA bridge, based on DACs
implemented by resistor ladders.
Those might or might not have an i2c bus routed to the VGA connector in
order to access the screen EDIDs.
Add a bridge that doesn't do anything but expose the modes available on the
screen, either based on the EDIDs if available, or based on the XGA
standards.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20160930143709.1388-3-maxime.ripard@free-electrons.com
Remove the unnecessary wrapper functions around drm_connector_cleanup().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161004222331.7200-1-marex@denx.de
- more core cleanup patches to prep drm_file to be used for
kernel-internal contexts (David Herrmann)
- more split-up+docs for drm_crtc.c
- lots of small fixes and polish all over
* tag 'topic/drm-misc-2016-09-25' of git://anongit.freedesktop.org/drm-intel: (37 commits)
drm: bridge: analogix/dp: mark symbols static where possible
drm/bochs: mark bochs_connector_get_modes() static
drm/bridge: analogix_dp: Improve panel on time
drm/bridge: analogix_dp: Don't read EDID if panel present
drm/bridge: analogix_dp: Remove duplicated code
Revert "drm/i2c: tda998x: don't register the connector"
drm: Fix plane type uabi breakage
dma-buf/sync_file: free fences array in num_fences is 1
drm/i2c: tda998x: don't register the connector
drm: Don't swallow error codes in drm_dev_alloc()
drm: Distinguish no name from ENOMEM in set_unique()
drm: Remove dirty property from docs
drm/doc: Document color space handling
drm: Extract drm_color_mgmt.[hc]
drm/doc: Polish plane composition property docs
drm: Conslidate blending properties in drm_blend.[hc]
drm/doc: Polish for drm_plane.[hc]
drm: Extract drm_plane.[hc]
drm/tilcdc: Add atomic and crtc headers to crtc.c
drm: Fix typo in encoder docs
...
We get 2 warnings when building kernel with W=1:
drivers/gpu/drm/bridge/analogix/analogix_dp_core.c:1053:5: warning: no previous prototype for 'analogix_dp_get_modes' [-Wmissing-prototypes]
drivers/gpu/drm/bridge/analogix/analogix_dp_core.c:1097:1: warning: no previous prototype for 'analogix_dp_detect' [-Wmissing-prototypes]
In fact, both functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
So this patch marks both functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1474788764-6069-1-git-send-email-baoyou.xie@linaro.org
In order to reduce the time required to turn on the panel, this patch
makes 2 assumptions:
1- In detect(): if there's a panel, we're connected.
2- In get_modes(): if there's a panel, let the panel driver decide if
it should prepare/unprepare in order to get the modes.
The first is straightforward, and shouldn't need further explanation. The
second should eliminate the prepare/unprepare delays from get_modes() in
most cases, since panels generally hardcode their modes in the driver as
opposed to reading EDID. If a panel does need to read EDID, it should be
responsible for ensuring it's in a state in which it can.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
If there's a panel connected to the analogix_dp bridge, rely on
the panel driver for modes, rather than reading EDID *and* calling
get_modes() on the panel.
This allows panels with a valid EDID to read it in the panel driver
(e.g. simple_panel), and panels with invalid EDID to homebrew modes
in their get_modes implementation.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Remove code for reading the EDID and DPCD fields and use the helpers
instead.
Besides the obvious code reduction, other helpers are being added to the
core that could be used in this driver and will be good to be able to
use them instead of duplicating them.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Yakir Yang <ykk@rock-chips.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Archit Taneja <architt@codeaurora.org>
- add active plane reconfiguration support (v4),
use the atomic_disable callback
- stop calling disable_plane manually in the plane destroy path
- let mode cleanup destroy mode objects on driver unbind
- drop deprecated load/unload drm_driver ops
- add exclusive fence to plane state, so the atomic helper can
wait on them, remove the open-coded fence wait from imx-drm
- add low level deinterlacer (VDIC) support
- add support for channel linking via the frame synchronisation unit (FSU)
- add queued image conversion support for memory-to-memory scaling, rotation,
and color space conversion, using IC and IRT.
-----BEGIN PGP SIGNATURE-----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=WtaT
-----END PGP SIGNATURE-----
Merge tag 'imx-drm-next-2016-09-19' of git://git.pengutronix.de/git/pza/linux into drm-next
imx-drm active plane reconfiguration, cleanup, FSU/IC/IRT/VDIC support
- add active plane reconfiguration support (v4),
use the atomic_disable callback
- stop calling disable_plane manually in the plane destroy path
- let mode cleanup destroy mode objects on driver unbind
- drop deprecated load/unload drm_driver ops
- add exclusive fence to plane state, so the atomic helper can
wait on them, remove the open-coded fence wait from imx-drm
- add low level deinterlacer (VDIC) support
- add support for channel linking via the frame synchronisation unit (FSU)
- add queued image conversion support for memory-to-memory scaling, rotation,
and color space conversion, using IC and IRT.
* tag 'imx-drm-next-2016-09-19' of git://git.pengutronix.de/git/pza/linux:
gpu: ipu-v3: Add queued image conversion support
gpu: ipu-v3: Add ipu_rot_mode_is_irt()
gpu: ipu-v3: fix a possible NULL dereference
drm/imx: parallel-display: detach bridge or panel on unbind
drm/imx: imx-ldb: detach bridge on unbind
drm/imx: imx-ldb: detach panel on unbind
gpu: ipu-v3: Add FSU channel linking support
gpu: ipu-v3: Add Video Deinterlacer unit
drm/imx: add exclusive fence to plane state
drm/imx: fold ipu_plane_disable into ipu_disable_plane
drm/imx: don't destroy mode objects manually on driver unbind
drm/imx: drop deprecated load/unload drm_driver ops
drm/imx: don't call disable_plane in plane destroy path
drm/imx: Add active plane reconfiguration support
drm/imx: Use DRM_PLANE_COMMIT_NO_DISABLE_AFTER_MODESET flag
drm/imx: ipuv3-crtc: Use the callback ->atomic_disable instead of ->disable
gpu: ipu-v3: Do not wait for DMFC FIFO to clear when disabling DMFC channel
The change adds support of internal HDMI I2C master controller, this
subdevice is used by default, if "ddc-i2c-bus" DT property is omitted.
The main purpose of this functionality is to support reading EDID from
an HDMI monitor on boards, which don't have an I2C bus connected to
DDC pins.
The current implementation does not support "I2C Master Interface
Extended Read Mode" to read data addressed by non-zero segment
pointer, this means that if EDID has more than 1 extension blocks,
EDID reading operation won't succeed, in my practice all tested HDMI
monitors have at maximum one extension block.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This change is needed to properly lock I2C bus driver, which serves
DDC.
The change fixes an overflow over zero of I2C bus driver user counter:
root@imx6q:~# lsmod
Not tainted
dw_hdmi_ahb_audio 4082 0 - Live 0xbf02c000
dw_hdmi_imx 3498 0 - Live 0xbf00d000
dw_hdmi 16398 2 dw_hdmi_ahb_audio,dw_hdmi_imx, Live 0xbf004000
i2c_imx 16687 0 - Live 0xbf017000
root@imx6q:~# rmmod dw_hdmi_imx
root@imx6q:~# lsmod
Not tainted
dw_hdmi_ahb_audio 4082 0 - Live 0xbf02c000
dw_hdmi 16398 1 dw_hdmi_ahb_audio, Live 0xbf004000
i2c_imx 16687 -1 - Live 0xbf017000
^^
root@imx6q:~# rmmod i2c_imx
rmmod: ERROR: Module i2c_imx is in use
Note that prior to this change put_device() coupled with
of_find_i2c_adapter_by_node() was missing on error path of
dw_hdmi_bind(), added i2c_put_adapter() there along with the change.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The Renesas Wheat board has 2 ADV7513 chips on the same I2C bus, however
the ADV751x driver only supports 1 chip as it tries to assign the packet/
EDID/CEC memory I2C devices to the fixed I2C addresses. Assign these I2C
addresses at the fixed offsets (derived from the programming guide) from
the main register map address instead.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1580212.O1LYdJFM97@wasted.cogentembedded.com
More -misc stuff
- moar drm_crtc.c split up&documentation
- some fixes for the simple kms helpers (Andrea)
- I included all the dri1 patches from David - we're not removing any code
or drivers, and it seems to have worked as a wake-up call to motivate a
few more people to upstream kms conversions for these. Feel free to
revert if you disagree strongly.
- a few other single patches
* tag 'topic/drm-misc-2016-08-31' of git://anongit.freedesktop.org/drm-intel: (24 commits)
drm: drm_probe_helper: Fix output_poll_work scheduling
drm: bridge/dw-hdmi: Fix colorspace and scan information registers values
drm/doc: Polish docs for drm_property&drm_property_blob
drm: Unify handling of blob and object properties
drm: Extract drm_property.[hc]
drm: move drm_mode_legacy_fb_format to drm_fourcc.c
drm/doc: Polish docs for drm_mode_object
drm: Remove drm_mode_object->atomic_count
drm: Extract drm_mode_object.[hc]
drm/doc: Polish kerneldoc for encoders
drm: Extract drm_encoder.[hc]
drm/fb-helper: don't call remove_conflicting_framebuffers for FB=m && DRM=y
drm/atomic-helper: Add NO_DISABLE_AFTER_MODESET flag support for plane commit
drm/atomic-helper: Disable appropriate planes in disable_planes_on_crtc()
drm/atomic-helper: Add atomic_disable CRTC helper callback
drm: simple_kms_helper: add support for bridges
drm: simple_kms_helper: make connector optional at init time
drm/bridge: introduce bridge detaching mechanism
drm/simple-helpers: Always add planes to the state update
drm: reduce GETCLIENT to a minimum
...
Colorspace and scan information values were being written in wrong
offsets. This patch corrects this and writes the values at the
offsets specified in the databook.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Carlos Palminha <palminha@synopsys.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/96fd0f06b7ebc2ee5cb8239a99648f3107e24497.1471530573.git.joabreu@synopsys.com
Instead let drm_mode_config_cleanup() do the work when taking down
the master device. This requires all cleanup functions to be
properly hooked up to the mode object .destroy callback.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This pull request contains the following rockchip drm changes:
- Introduce support for rk3399 vop/crtc
- Add PSR framework to the rockchip driver
- Implement PSR in the rockchip analogix edp driver
- Fix panel on/off in analogix to avoid damaging panels
- Some miscellaneous fixes to clean up logs and code readability
* 'for-next' of git://people.freedesktop.org/~seanpaul/dogwood:
drm/rockchip: analogix_dp: drop unnecessary probe deferral "error" print
drm/rockchip: Enable vblank without event
drm/rockchip: Improve analogix-dp psr handling
drm/rockchip: A couple small fixes to psr
drm/rockchip: Use a spinlock to protect psr state
drm/rockchip: Don't use a delayed worker for psr state changes
drm/rockchip: Convert psr_list_mutex to spinlock and use it
drm/rockchip: analogix_dp: implement PSR function
drm/bridge: analogix_dp: add the PSR function support
drm/rockchip: add an common abstracted PSR driver
drm/rockchip: vop: export line flag function
drm/bridge: analogix_dp: Ensure the panel is properly prepared/unprepared
dt-bindings: add compatible strings for big/little rockchip vops
dt-bindings: sort Rockchip vop compatible by chip's number
drm/rockchip: vop: add rk3399 vop support
drm/rockchip: vop: introduce VOP_REG_MASK
drm/rockchip: sort registers define by chip's number
The full name of PSR is Panel Self Refresh, panel device could refresh
itself with the hardware framebuffer in panel, this would make lots of
sense to save the power consumption.
This patch have exported two symbols for platform driver to implement
the PSR function in hardware side:
- analogix_dp_active_psr()
- analogix_dp_inactive_psr()
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Instead of just preparing the panel on bind, actually prepare/unprepare
during modeset/disable. The panel must be prepared in order to read hpd
status and edid, so we need to keep state around the prepares in order
to ensure we don't accidentally turn the panel off at the wrong time.
Reviewed-by: Yakir Yang <ykk@rock-chips.com>
Tested-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
A few more simple fixes that Sean&I collected. There's a bunch of bigger
things on dri-devel, but I think those are all too late for 4.8 really.
I'll try and go collect them after -rc1 for 4.9.
* tag 'topic/drm-misc-2016-07-28' of git://anongit.freedesktop.org/drm-intel:
drm/arm: mali-dp: Fix error return code in malidp_bind()
drm/arm: mali-dp: Remove redundant dev_err call in malidp_bind()
drm/gma500: remove unnecessary stub for fb_ioctl()
apple-gmux: Sphinxify docs
drm/arm: mali-dp: Set crtc.port to the port instead of the endpoint
drm/sti: use new Reset API
drm/etnaviv: Optimize error handling in etnaviv_gem_new_userptr()
drm/etnaviv: Delete unnecessary checks before two function calls
drm/vmwgfx: Delete an unnecessary check before the function call "vfree"
drm/qxl: Delete an unnecessary check before drm_gem_object_unreference_unlocked()
drm/mgag200: Delete an unnecessary check before drm_gem_object_unreference_unlocked()
drm/bridge: ps8622: Delete an unnecessary check before backlight_device_unregister()
GPU-DRM-GMA500: Delete unnecessary checks before two function calls
GPU-DRM-OMAP: Delete unnecessary checks before two function calls
The backlight_device_unregister() function tests whether its argument
is NULL and then returns immediately.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/791089e4-201c-ad01-9c3b-f49835765177@users.sourceforge.net
This is an update to the previous drm bridge pull request. The ADV7511
driver's conversion from slave encoder to bridge meant that its users
(the rcar-du kms driver) should use the bridge interface too. This pull
request now also contains a commit that updates the rcar-du's hdmi encoder
interface from slave encoder to bridge.
The other updates are as before:
- Converts the ADV7511 i2c slave encoder driver to a bridge driver.
Adds support for the ADV7533 bridge chip.
- Add bridge driver for TC358767 (DSI/DPI to eDP) encoder chips.
* 'drm_bridge_for_4.8' of https://github.com/boddob/linux:
drm: rcar-du: Remove i2c slave encoder interface for hdmi encoder
drm/bridge: tc358767: Add DPI to eDP bridge driver
dt-bindings: tc358767: add DT documentation
dt-bindings: drm/bridge: Update bindings for ADV7533
drm/bridge: adv7533: Change number of DSI lanes dynamically
drm/bridge: adv7533: Use internal timing generator
drm/bridge: adv7533: Create a MIPI DSI device
drm/bridge: adv7533: Initial support for ADV7533
drm/bridge: adv7511: Fix mutex deadlock when interrupts are disabled
drm/i2c: adv7511: Move to bridge folder
drm/i2c: adv7511: Convert to drm_bridge
Add a drm_bridge driver for the Toshiba TC358767 DPI/DSI to
eDP/DP bridge. Currently only DPI input with 24-bit RGB is
supported.
Signed-off-by: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Please consider merging this tag, which contains the v4 misc fixes and add RK3399 eDP support patches[0] I sent on 2016-06-29, rebased onto v4.7-rc5.
* 'upstream/analogix-dp-20160705' of git://github.com/yakir-Yang/linux:
dt-bindings: analogix_dp: rockchip: correct the wrong compatible name
drm/rockchip: analogix_dp: introduce the pclk for grf
drm/bridge: analogix_dp: fix no drm hpd event when panel plug in
drm/rockchip: analogix_dp: update the comments about why need to hardcode VOP output mode
drm/rockchip: analogix_dp: correct the connector display color format and bpc
drm/bridge: analogix_dp: passing the connector as an argument in .get_modes()
drm/rockchip: analogix_dp: make panel detect to an optional action
drm/rockchip: analogix_dp: add rk3399 eDP support
drm/bridge: analogix_dp: some rockchip chips need to flip REF_CLK bit setting
drm/bridge: analogix_dp: correct the register bit define error in ANALOGIX_DP_PLL_REG_1
drm/rockchip: analogix_dp: split the lcdc select setting into device data
Lower modes on ADV7533 require lower number of DSI lanes for correct
operation. If ADV7533 is being used with 4 DSI lanes, then switch the
lanes to 3 when the target mode's pixel clock is less than 80 Mhz.
Based on patch by Andy Green <andy.green@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
ADV7533 provides an internal timing generator for certain modes that it
can't use the DSI clock directly.
We've observed that HDMI is more stable with the internal timing
generator, especially if there are instabilities in the DSI clock source.
The data spec also seems to recommend the usage of the timing generator
for all modes.
However, on some platforms, it's reported that enabling the timing
generator causes instabilities with the HDMI output.
Create a DT parameter that lets a platform explicitly disable the timing
generator. The timing generator is enabled by default.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
In order to pass DSI specific parameters to the DSI host, we need the
driver to create a mipi_dsi_device DSI device that attaches to the
host.
Use of_graph helpers to get the DSI host DT node. Create a MIPI DSI
device using this host. Finally, attach this device to the DSI host.
Populate DT parameters (number of data lanes for now) that are required
for DSI RX to work correctly. Hardcode few other parameters (rgb,
embedded_sync) for now.
Select DRM_MIPI_DSI config option only when ADV7533 support is enabled.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
ADV7533 is a DSI to HDMI encoder chip. It is a derivative of ADV7511,
with additional blocks to translate input DSI data to parallel RGB
data. Besides the ADV7511 I2C register map, it has additional registers
that require to be configured to activate the DSI Rx block.
Create a new config that enables ADV7533 support. Use DT compatible
strings to populate the ADV7533 type enum. Add minimal register
configurations belonging to the DSI/CEC register map. Keep the ADV7533
code in a separate file.
Originally worked on by Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
When the adv7511 i2c client doesn't have an interrupt line, we observe a
deadlock on caused by trying to lock drm device's mode_config.mutex twice
in the same context.
Here is the sequence that causes it:
ioctl DRM_IOCTL_MODE_GETCONNECTOR from userspace
drm_mode_getconnector (acquires mode_config mutex)
connector->fill_modes()
drm_helper_probe_single_connector_modes
connector_funcs->get_modes
adv7511_encoder_get_modes
adv7511_get_edid_block
adv7511_irq_process
drm_helper_hpd_irq_event (acquires mode_config mutex again)
In adv7511_irq_process, don't call drm_helper_hpd_irq_event when not
called from the interrupt handler. It doesn't serve any purpose there
anyway.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
The driver has been converted to use drm_bridge instead of
drm_i2c_slave_encoder. We can now move it to the bridge folder.
Create a separate folder since we already have a couple of files and
expect more when we support audio and ADV7533.
Rename the driver to adv7511_drv.c. This will come in handy later
when the driver module will need to be built from multiple object
files.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
There is no one using the legacy drm_connector_funcs structure since
the imx-drm has been converted to atomic, so we may remove it.
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Wire up CRTCs', planes' and connectors' ->reset, ->duplicate and ->destroy state
hooks to use the default implementations from the atomic helper library.
The helpers track each DRM object state.
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The enum value of DP_IRQ_TYPE_HP_CABLE_IN is zero, but driver only
send drm hp event when the irq_type and the enum value is true.
if (irq_type & DP_IRQ_TYPE_HP_CABLE_IN || ...)
drm_helper_hpd_irq_event(dp->drm_dev);
So there would no drm hpd event when cable plug in, to fix that
just need to assign all hotplug enum with no-zero values.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Stéphane Marchesin <marcheu@chromium.org>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
It's better to pass the connector to platform driver in .get_modes()
callback, just like what the .get_modes() helper function designed.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
RK3399 and RK3288 shared the same eDP IP controller, only some light
difference with VOP configure and GRF configure.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
As vendor document indicate, when REF_CLK bit set 0, then DP
phy's REF_CLK should switch to 24M source clock.
But due to IC PHY layout mistaken, some chips need to flip this
bit(like RK3288), and unfortunately they didn't indicate in the
DP version register. That's why we have to make this little hack.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
There're an register define error in ANALOGIX_DP_PLL_REG_1 which introduced
by commit bcec20fd5a ("drm: bridge: analogix/dp: add some rk3288 special
registers setting").
The PHY PLL input clock source is selected by ANALOGIX_DP_PLL_REG_1
BIT 0, not BIT 1.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Add basic support for the sii902x RGB -> HDMI bridge.
This driver does not support audio output yet.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
---
Changes in v8:
- remove useless headers inclusion
- fix macro names (s/SIL/SII)
- drop unneeded hotplug_work field from struct sii902x
- drop drm_connector_unregister() call in the ->destroy() method
- add a timeout when polling a register value
Changes in v6:
- use HDMI_INFOFRAME_SIZE(AVI)
- fix reset_gpio initialization
- reduce the reset time based on Ming feedback
Changes in v5:
- drop the best_encoder() implementation
Changes in v4:
- make reset GPIO optional
- only support attaching to DRM devices supporting atomic updates
Changes in v3:
- fix get_modes() implementation to avoid turning the screen in power
save mode
- rename the driver (sil902x -> sii902x)
Changes in v2:
- fix errors reported by the kbuild robot
fixup! drm: bridge: Add sii902x driver
We have a 1:1 relationship between connectors and encoders, which means
we can rely on the drm_atomic_helper_best_encoder() behavior.
We still have to explicitly assign ->best_encoder() to
drm_atomic_helper_best_encoder(), because the automated fallback to
drm_atomic_helper_best_encoder() when ->best_encoder() is NULL is only
available when the DRM device is using the atomic helpers, and this bridge
is compatible with non-atomic and atomic devices.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465300095-16971-21-git-send-email-boris.brezillon@free-electrons.com
Although there are other chips from the same family that can reuse this
driver, at the moment we only tested ANX7814 chip.
The ANX7814 is an ultra-low power Full-HD (1080p60) SlimPort transmitter
designed for portable devices. This driver adds initial support for HDMI
to DP pass-through mode.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Daniel Kurtz <djkurtz@chromium.org>
Cc: Nicolas Boichat <drinkcat@chromium.org>
Cc: Thierry Reding <treding@nvidia.com>
[treding@nvidia.com: coding style, propagate regulator_get() errors]
Signed-off-by: Thierry Reding <treding@nvidia.com>
This pull request want to land the analogix_dp driver into drm/bridge directory,
which reused the Exynos DP code, and add Rockchip DP support. And those
patches have been:
* 'drm-next-analogix-dp-v2' of github.com:yakir-Yang/linux:
drm: bridge: analogix/dp: Fix the possible dead lock in bridge disable time
drm: bridge: analogix/dp: add panel prepare/unprepare in suspend/resume time
drm: bridge: analogix/dp: add edid modes parse in get_modes method
drm: bridge: analogix/dp: move hpd detect to connector detect function
drm: bridge: analogix/dp: try force hpd after plug in lookup failed
drm: bridge: analogix/dp: add max link rate and lane count limit for RK3288
drm: bridge: analogix/dp: add some rk3288 special registers setting
dt-bindings: add document for rockchip variant of analogix_dp
drm: rockchip: dp: add rockchip platform dp driver
ARM: dts: exynos/dp: remove some properties that deprecated by analogix_dp driver
dt-bindings: add document for analogix display port driver
drm: bridge: analogix/dp: dynamic parse sync_pol & interlace & dynamic_range
drm: bridge: analogix/dp: remove duplicate configuration of link rate and link count
drm: bridge: analogix/dp: fix some obvious code style
drm: bridge: analogix/dp: rename register constants
drm/exynos: dp: rename implementation specific driver part
drm: bridge: analogix/dp: split exynos dp driver to bridge directory
It may caused a dead lock if we flush the hpd work in bridge disable time.
The normal flow would like:
IN --> DRM IOCTL
1. Acquire crtc_ww_class_mutex (DRM IOCTL)
IN --> analogix_dp_bridge
2. Acquire hpd work lock (Flush hpd work)
3. HPD work already in idle, no need to run the work function.
OUT <-- analogix_dp_bridge
OUT <-- DRM IOCTL
The dead lock flow would like:
IN --> DRM IOCTL
1. Acquire crtc_ww_class_mutex (DRM IOCTL)
IN --> analogix_dp_bridge
2. Acquire hpd work lock (Flush hpd work)
IN --> analogix_dp_hotplug
IN --> drm_helper_hpd_irq_event
3. Acquire mode_config lock (This lock already have been acquired in previous step 1)
** Dead Lock Now **
It's wrong to flush the hpd work in bridge->disable time, I guess the
original code just want to ensure the delay work must be finish before
encoder disabled.
The flush work in bridge disable time is try to ensure the HPD event
won't be missed before display card disabled, actually we can take a
fast respond way(interrupt thread) to update DRM HPD event to fix the
delay update and possible dead lock.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Turn off the panel power in suspend time would help to reduce
power waste.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Display Port monitor could support kinds of mode which indicate
in monitor edid, not just one single display resolution which
defined in panel or devivetree property display timing.
Note: Gustavo Padovan try to remove the controller and phy
power on function in bind time at bellow commit:
drm/exynos: do not start enabling DP at bind() phase
But for now driver need to read edid message in .get_modes()
function, so controller must be inited in bind time, so we
need to add controller init back.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
This change just make a little clean to make code more like
drm core expect, move hdp detect code from bridge->enable(),
and place them into connector->detect().
Note: Gustavo Padovan try to remove the controller and phy
power on function in bind time at bellow commit:
drm/exynos: do not start enabling DP at bind() phase
But for now the connector status don't hardcode to connected,
need to operate dp phy in .detect function, so we need to revert
parts if Gustavo Padovan's changes, add phy poweron
function in bind time.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Some edp screen do not have hpd signal, so we can't just return
failed when hpd plug in detect failed.
This is an hardware property, so we need add a devicetree property
"analogix,need-force-hpd" to indicate this sutiation.
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
There are some IP limit on rk3288 that only support 4 physical lanes
of 2.7/1.6 Gbps/lane, so seprate them out by device_type flag.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
RK3288 need some special registers setting, we can separate
them out by the dev_type of plat_data.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Both hsync/vsync polarity and interlace mode can be parsed from
drm display mode, and dynamic_range and ycbcr_coeff can be judge
by the video code.
But presumably Exynos still relies on the DT properties, so take
good use of mode_fixup() in to achieve the compatibility hacks.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
link_rate and lane_count already configured in analogix_dp_set_link_train(),
so we don't need to config those repeatly after training finished, just
remove them out.
Beside Display Port 1.2 already support 5.4Gbps link rate, the maximum sets
would change from {1.62Gbps, 2.7Gbps} to {1.62Gbps, 2.7Gbps, 5.4Gbps}.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Fix some obvious alignment problems, like alignment and line
over 80 characters problems, make this easy to be maintained
later.
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
In the original split we kept the register constants intact to keep the
diff small. Still the constants are Analogix-specific, so rename them now.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Split the dp core driver from exynos directory to bridge directory,
and rename the core driver to analogix_dp_*, rename the platform
code to exynos_dp.
Beside the new analogix_dp driver would export six hooks.
"analogix_dp_bind()" and "analogix_dp_unbind()"
"analogix_dp_suspned()" and "analogix_dp_resume()"
"analogix_dp_detect()" and "analogix_dp_get_modes()"
The bind/unbind symbols is used for analogix platform driver to connect
with analogix_dp core driver. And the detect/get_modes is used for analogix
platform driver to init the connector.
They reason why connector need register in helper driver is rockchip drm
haven't implement the atomic API, but Exynos drm have implement it, so
there would need two different connector helper functions, that's why we
leave the connector register in helper driver.
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Since your main drm-next pull isn't out of the door yet I figured I might
as well flush out drm-misc instead of delaying for 4.6. It's really just
random stuff all over, biggest thing probably connector_mask tracking from
Maarten.
* tag 'topic/drm-misc-2016-01-17' of git://anongit.freedesktop.org/drm-intel: (24 commits)
drm/fb_cma_helper: Remove implicit call to disable_unused_functions
drm/sysfs: use kobj_to_dev()
drm/i915: Init power domains early in driver load
drm: Do not set connector->encoder in drivers
apple-gmux: Add initial documentation
drm: move MODULE_PARM_DESC to other file
drm/edid: index CEA/HDMI mode tables using the VIC
drm/atomic: Remove drm_atomic_connectors_for_crtc.
drm/i915: Update connector_mask during readout, v2.
drm: Remove opencoded drm_gem_object_release_handle()
drm: Do not set outparam on error during GEM handle allocation
drm/docs: more leftovers from the big vtable documentation pile
drm/atomic-helper: Reject legacy flips on a disabled pipe
drm/atomic: add connector mask to drm_crtc_state.
drm/tegra: Use __drm_atomic_helper_reset_connector for subclassing connector state, v2.
drm/atomic: Add __drm_atomic_helper_connector_reset, v2.
drm/i915: Set connector_state->connector using the helper.
drm: Use a normal idr allocation for the obj->name
drm: Only bump object-reference count when adding first handle
drm: Balance error path for GEM handle allocation
...
An encoder is associated with a connector by the DRM core as a result of
setting up a configuration. Drivers using the atomic or legacy helpers
should never set up this link, even if it is a static one.
While at it, try to catch this kind of error in the future by adding a
WARN_ON() in drm_mode_connector_attach_encoder(). Note that this doesn't
cover all the cases, since drivers could set this up after attaching.
Drivers that use the atomic helpers will get a warning later on, though,
so hopefully the two combined cover enough to help people avoid this in
the future.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Liviu Dudau <Liviu.Dudau@arm.com>
Cc: Mark yao <mark.yao@rock-chips.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1447694393-24700-1-git-send-email-thierry.reding@gmail.com
Fill atomic needed funcs with default atomic helper library.
Rockchip use dw_hdmi, and drm/rockchip will covert to atomic api,
we need dw_hdmi support atomic funcs.
Now another drm driver use dw_hdmi is imx, not yet atomic, so
check DRIVER_ATOMIC at runtime to spilt atomic and not atomic.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Seems I lied in my last drm-misc pull request and suddenly there's a big
pile of random stuff. Boris dug out Thierry's drm-trivial branch and
resubmitted everything since that branch didn't really work out.
On top of that Nicolas' changes to drm_dev_set_unique - this might
conflict with new driver pulls (I double checked and current drm-next
should be fine), so please beware. The -next/-fixes conflict in vmwgfx
will change slightly with this here too.
* tag 'topic/drm-misc-2015-12-18' of git://anongit.freedesktop.org/drm-intel: (36 commits)
drm: use dev_name as default unique name in drm_dev_alloc()
drm: make drm_dev_set_unique() not use a format string
drm/vmwgfx: Constify function pointer structs
drm/udl: Constify function pointer structs
drm/tegra: Constify function pointer structs
drm/rockchip: Constify function pointer structs
drm/nouveau: Constify function pointer structs
drm/mgag200: Constify function pointer structs
drm/imx: Constify function pointer structs
drm/i2c/sil164: Constify function pointer structs
drm/i2c/adv7511: Constify function pointer structs
drm/exynos: Constify function pointer structs
drm/cirrus: Constify function pointer structs
drm/i2c/ch7006: Constify function pointer structs
drm/bridge/nxp-ptn3460: Constify function pointer structs
drm/bridge/dw_hdmi: Constify function pointer structs
drm/bochs: Constify function pointer structs
drm/atmel-hlcdc: Constify function pointer structs
drm/armada: Constify function pointer structs
drm: Constify drm_encoder_slave_funcs
...
Moves a bunch of junk to .rodata from .data.
drivers/gpu/drm/bridge/nxp-ptn3460.ko:
-.rodata 440
+.rodata 536
-.data 208
+.data 112
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-16-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Moves a bunch of junk to .rodata from .data.
drivers/gpu/drm/bridge/dw_hdmi.ko:
-.rodata 120
+.rodata 216
-.data 96
+.data 0
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-15-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just two small cleanup patches to fix coccinelle warnings.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Q9bM
-----END PGP SIGNATURE-----
Merge tag 'drm/panel/for-4.4-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/panel: Changes for v4.4-rc1
Just two small cleanup patches to fix coccinelle warnings.
* tag 'drm/panel/for-4.4-rc1' of git://anongit.freedesktop.org/tegra/linux:
drm/bridge: ptn3460: Fix coccinelle warnings
drm/bridge: ps8622: Fix coccinelle warnings
The platform_no_drv_owner.cocci coccinelle script generates the
following warning:
drivers/gpu/drm/bridge/nxp-ptn3460.c:403:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically. Patch
generated by scripts/coccinelle/api/platform_no_drv_owner.cocci.
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The platform_no_drv_owner.cocci coccinelle script generates the
following warning:
drivers/gpu/drm/bridge/parade-ps8622.c:671:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically. Patch
generated by scripts/coccinelle/api/platform_no_drv_owner.cocci.
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Given the TDMS clock, audio sample rate, and the N parameter, we can
calculate the CTS value for the audio clock regenerator (ACR) using the
following calculation given in the HDMI specification:
CTS = ftdms * N / (128 * fs)
The specification says that the CTS value is an average value, which is
true if the source hardware measures it. Where source hardware needs it
to be programmed, it is particularly difficult to alternate between two
values correctly to ensure that we achieve a correct "average"
fractional value at the sink.
Also, there's the problem that our "ftdms" is not a fully accurate
value; it is rounded to a kHz value. This introduces an unnecessary
(and harmless) fractional value into the above equation for combinations
like 148.5MHz/1.001 for 44100Hz - we still calculate the correct CTS
value.
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We never set the ratio for CTS/N calculation for the audio clock
regenerator (ACR) to anything but 100, so this adds pointless
complexity. Should we support pixel repetition, we should update the
CTS/N calculation code to use those parameters or the actual TMDS clock
rate instead of a ratio.
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adjust the pixel clock values in the N calculation to match the more
accurate clock values we're given by the DRM subsystem, which are the
kHz pixel rate, with any fractional kHz rounded down in the case of
the non-240, non-480 line modes, or rounded up for the others. So,
25.20 / 1.001 => 25175
27.00 * 1.001 => 27027
74.25 / 1.001 => 74176
148.50 / 1.001 => 148352
DRM derives these rates from the EDID CEA mode identifiers, which are
looked up in the tables in drivers/gpu/drm/drm_edid.c. The values on
the right are the clock values found in these tables, and are
currently expected to be passed to the HDMI driver unchanged.
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's no need to be recursive when computing the N value for the ACR
packet - we can instead calculate the multiplier prior to our switch()
based lookup, and multiply the N value appropriately afterwards.
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With multichannel audio, we need to allow larger buffer sizes to avoid
XRUNs during playback. Push the buffer size up to 1024K, but as we
maintain two buffers, ensure that the vmalloc buffer does not exceed
the userspace buffer size.
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add basic support for multi-channel PCM audio, with fixed speaker
mappings. This has been tested with an AV receiver, and appears to
work for low sample rates up to 8 channels.
It should be noted that multi-channel mode using the IEC958 alsa-lib
conversion plugin requires correct AES channel status for the AV
receiver to recognise the stream, especially the sample rate bits.
"Not identified" does not work there.
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Parse the ELD (EDID like data) stored from the HDMI driver to restrict
the sample rates and channels which are available to ALSA. This causes
the ALSA device to reflect the capabilities of the overall audio path,
not just what is supported at the HDMI source interface level.
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add ALSA based HDMI AHB audio driver for dw_hdmi. The only buffer
format supported by the hardware is its own special IEC958 based format,
which is not compatible with any ALSA format. To avoid doing too much
data manipulation within the driver, we support only ALSAs IEC958 LE and
24-bit PCM formats for 2 to 6 channels, which we convert to its hardware
format.
A more desirable solution would be to have this conversion in userspace,
but ALSA does not appear to allow such transformations outside of
libasound itself.
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
HDMI sinks are permitted to de-assert and re-assert the HPD signal to
indicate that their EDID has been updated, which may not involve a
change of video information.
An example of where such a situation can arise is when an AV receiver
is connected between the source and the display device. Events which
can cause the HPD to be deasserted include:
* turning on or switching to standby the AV receiver.
* turning on or switching to standby the display device.
Each of these can change the entire EDID data, or just a part of the
EDID data - it's up to the connected HDMI sink to do what they desire
here. For example
- with the AV receiver and display device both in standby, a source
connected to the AV receiver may provide its own EDID to the source.
- turning on the display device causes the display device's EDID to be
made available in an unmodified form to the source.
- subsequently turning on the AV receiver then provides a modified
version of the display device's EDID.
Moreover, HPD doesn't tell us whether something is actually listening
on the HDMI TDMS signals. The phy gives us a set of RXSENSE indications
which tell us whether there is a sink connected to the TMDS signals.
Currently, we use the HPD signal to enable or disable the HDMI block,
which is questionable when HPD is used in this manner. Using the
RXSENSE would be more appropriate, but there is some bad behaviour
which needs to be coped with. The iMX6 implementation lets the TMDS
signals float when the phy is "powered down", which cause spurious
interrupts. Rather than just using RXSENSE, use RXSENSE and HPD
becoming both active to signal the presence of a device, but loss
of RXSENSE to indicate that the device has been unplugged.
The side effect of this change is that a sink deasserting the HPD
signal to cause a re-read of the EDID data will not cause the bridge
to immediately disable the video signal.
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When connected to HDMI sources, some DVI monitors de-assert their HPD
signal and TDMS loads for one seconds every four seconds when there is
no signal present on the connection.
Unfortunately, this behaviour is indistinguishable from a proper HDMI
setup with an AV receiver in the path to the display: the HDMI spec
requires us to detect HPD deassertions as short as 100ms, which indicate
that the EDID has changed.
Since it is possible to connect a DVI monitor to an AV receiver and then
to a HDMI source, merely working around this by detecting the lack of
HDMI vendor block in the EDID is insufficient - the AV receiver is at
liberty to modify the EDID as it sees fit, and it will place its own
parameters into the EDID including the HDMI vendor block.
DRM has support for forcing the state of a connector, which we should
implement to allow us to work around these broken DVI monitors - we can
tell DRM to force the connection state to indicate that there is always
a device connected to work around this problem. Although this requires
manual configuration, it is better than nothing at all.
When a forced connection state has been set, there is no point handling
our RXSENSE interrupts, so disable them in this circumstance.
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for interlaced video modes to the dw_hdmi bridge. This
mainly involves halving the vertical parameters to be programmed into
the bridge registers, and setting the interlace_allowed connector flag.
This brings working 1080i support. However, 480i and 576i fail to
work due to the lack of proper pixel repetition support, which is not
trivial to add due to the tabular PLL parameterisation. Hence, we
filter out these modes in our mode_valid() method.
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Here are some development updates for the Synopsis Designware HDMI driver,
which clean up some of the code, and start preparing to add audio support
to the driver. This series of patches are based on a couple of dependent
commits from the ALSA tree.
Briefly, the updates are:
- move comments which should have moved with the phy values to the IMX
part of the driver.
- clean up the phy configuration: to all lookups before starting to
program the phy.
- clean up the HDMI clock regenerator code
- use the drm_hdmi_avi_infoframe_from_display_mode() helper which allows
the code to be subsequently simplified
- remove the unused 'regmap' pointer in struct dw_hdmi
- use the bridge drm device rather than the connector (we're the bridge
code)
- remove private hsync/vsync/interlaced flags, getting them from the
DRM mode structure instead.
- implement interface functions to support audio - setting the audio
sample rate, and enabling the audio clocks.
- removal of broken pixel repetition support
- cleanup DVI vs HDMI sink handling
- enable audio only if connected device supports audio
- avoid double-enabling bridge in the sink path (once in mode_set, and
again in commit)
- rename mis-named dw_hdmi_phy_enable_power()
- fix bridge enable/disable handing, so a plug-in event doesn't
reconfigure the bridge if DRM has disabled the output
- fix from Vladimir Zapolskiy for the I2CM_ADDRESS macro name
These are primerily preparitory patches for the AHB audio driver and
the I2S audio driver (from Rockchip) for this IP.
* 'drm-dwhdmi-devel' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm: bridge/dw_hdmi: fix register I2CM_ADDRESS register name
drm: bridge/dw_hdmi: fix phy enable/disable handling
drm: bridge/dw_hdmi: rename dw_hdmi_phy_enable_power()
drm: bridge/dw_hdmi: avoid enabling interface in mode_set
drm: bridge/dw_hdmi: enable audio only if sink supports audio
drm: bridge/dw_hdmi: clean up HDMI vs DVI mode handling
drm: bridge/dw_hdmi: don't support any pixel doubled modes
drm: bridge/dw_hdmi: remove pixel repetition setting for all VICs
drm: bridge/dw_hdmi: introduce interfaces to enable and disable audio
drm: bridge/dw_hdmi: introduce interface to setting sample rate
drm: bridge/dw_hdmi: remove mhsyncpolarity/mvsyncpolarity/minterlaced
drm: bridge/dw_hdmi: use our own drm_device
drm: bridge/dw_hdmi: remove unused 'regmap' struct member
drm: bridge/dw_hdmi: simplify hdmi_config_AVI() a little
drm: bridge/dw_hdmi: use drm_hdmi_avi_infoframe_from_display_mode()
drm: bridge/dw_hdmi: clean up hdmi_set_clk_regenerator()
drm: bridge/dw_hdmi: clean up phy configuration
drm: imx/dw_hdmi: move phy comments
drm/edid: add function to help find SADs
I2CM_ADDRESS became a MESS, fix it, also change guarding define
to __DW_HDMI_H__ , since the driver is not IMX specific.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The dw_hdmi enable/disable handling is particularly weak in several
regards:
* The hotplug interrupt could call hdmi_poweron() or hdmi_poweroff()
while DRM is setting a mode, which could race with a mode being set.
* Hotplug will always re-enable the phy whenever it detects an active
hotplug signal, even if DRM has disabled the output.
Resolve all of these by introducing a mutex to prevent races, and a
state-tracking bool so we know whether DRM wishes the output to be
enabled. We choose to use our own mutex rather than ->struct_mutex
so that we can still process interrupts in a timely fashion.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
dw_hdmi_phy_enable_power() is not about enabling and disabling power.
It is about allowing or preventing power-down mode being entered - the
register is documented as "Power-down enable (active low 0b)."
This can be seen as the bit has no effect when the HDMI phy is
operational on iMX6 hardware.
Rename the function to dw_hdmi_phy_enable_powerdown() to reflect the
documentation, make it take a bool for the 'enable' argument, and invert
the value to be written.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On a mode set, DRM makes the following sequence of calls:
* for_each_encoder
* bridge mode_fixup
* encoder mode_fixup
* crtc mode_fixup
* for_each_encoder
* bridge disable
* encoder prepare
* bridge post_disable
* disable unused encoders
* crtc prepare
* crtc mode_set
* for_each_encoder
* encoder mode_set
* bridge mode_set
* crtc commit
* for_each_encoder
* bridge pre_enable
* encoder commit
* bridge enable
dw_hdmi enables the HDMI output in both the bridge mode_set() and also
the bridge enable() step. This is duplicated work - we can avoid the
setup in mode_set() and just do it in the enable() stage. This
simplifies the code a little.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Only enable audio support if the sink supports audio in some form, as
defined via its EDID. We discover this capability using the generic
drm_detect_monitor_audio() function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The FSL kernel detects the HDMI vendor id, and uses this to set
hdmi->edid_cfg.hdmi_cap, which is then used to set mdvi appropriately,
rather than detecting whether we are outputting a CEA mode. Update
the dw_hdmi code to use this logic, but lets eliminate the mdvi
variable, prefering the more verbose "hdmi->sink_is_hdmi" instead.
Use the generic drm_detect_hdmi_monitor() to detect a HDMI sink.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As mentioned in the previous commit, the dw-hdmi driver does not support
pixel doubled modes at present; it does not configure the PLL correctly
for these modes. Therefore, filter out the double-clocked modes as we
presently are unable to support them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
dw_hdmi sets a pixel repetition factor of 1 for VICs 10-15, 25-30 and
35-38. However, DRM uses their native resolutions in its timing
information. For example, VIC 14 can be 1440x480 with no repetition,
or 720x480 with one pixel repetition. As DRM uses 1440 pixels per line
for this video mode, we need no pixel repetition.
In any case, pixel repetition appears broken in dw_hdmi.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
iMX6 devices suffer from an errata (ERR005174) where the audio FIFO can
be emptied while it is partially full, resulting in misalignment of the
audio samples.
To prevent this, the errata workaround recommends writing N as zero
until the audio FIFO has been loaded by DMA. Writing N=0 prevents the
HDMI bridge from reading from the audio FIFO, effectively disabling
audio.
This means we need to provide the audio driver with a pair of functions
to enable/disable audio. These are dw_hdmi_audio_enable() and
dw_hdmi_audio_disable().
A spinlock is introduced to ensure that setting the CTS/N values can't
race, ensuring that the audio driver calling the enable/disable
functions (which are called in an atomic context) can't race with a
modeset.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Introduce dw_hdmi_set_sample_rate(), which allows us to configure the
audio sample rate, setting the CTS/N values appropriately.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the struct hdmi_vmode mhsyncpolarity/mvsyncpolarity/minterlaced
members, which are only used within a single function. We can directly
reference the appropriate mode->flags instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When a YCBCR format is selected, we can merely copy the colorimetry
information directly as we use the same definitions for both the
unpacked AVI info frame and the hdmi_data_info structure.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Clean up hdmi_set_clk_regenerator() by allowing it to take the audio
sample rate and ratio directly, rather than hiding it inside the
function. Raise the unsupported pixel clock/sample rate message from
debug to error level as this results in audio not working correctly.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The phy configuration is dependent on the SoC, and we look up values for
some of the registers in SoC specific data. However, we had partially
programmed the phy before we had successfully looked up the clock rate.
Also, we were only checking that we had a valid configuration for the
currctrl register.
Move all these lookups to the start of this function instead, so we can
check that all lookups were successful before beginning to program the
phy.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The phy comments in dw_hdmi.c applied to the iMX6 version. Move these
comments to the iMX6 dw_hdmi-imx data along side the data.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Put the Kconfig entries for bridge drivers into a separate menu so that
they are automatically grouped and don't clutter up the top-level menu.
While at it, move the bridge menu towards the end of the top-level menu
where the panel menu is already located.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use vendor prefixes for Kconfig symbols and filenames. This should make
it easier to identify the various bridge drivers and to organize the
directory.
v2: fix object name for dw-hdmi (Fabio Estevam)
Signed-off-by: Thierry Reding <treding@nvidia.com>
Run dpms operations through the atomic intefaces. This basically removes
the .dpms() callback from econders and crtcs and use .disable() and
.enable() to turn the crtc on and off.
v2: Address comments by Joonyoung:
- make hdmi code call ->disable() instead of ->dpms()
- do not use WARN_ON on crtc enable/disable
v3: - Fix build failure after the hdmi change in v2
- Change dpms helper of ptn3460 bridge
v4: - remove win_commit() call from .enable()
v5: - move .atomic_check() to the atomic PageFlip patch, and transform it
in .atomic_begin()
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Set CRTC, planes and connectors to use the default implementations from
the atomic helper library. The helpers will work to keep track of state
for each DRM object.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This header file declares prototypes of functions that are no longer
used. Remove this file and all references to it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
If GPIOLIB=n and asm-generic/gpio.h is not used:
drivers/gpu/drm/bridge/ps8622.c: In function ‘ps8622_pre_enable’:
drivers/gpu/drm/bridge/ps8622.c:368: error: implicit declaration of function ‘gpiod_set_value’
drivers/gpu/drm/bridge/ps8622.c: In function ‘ps8622_probe’:
drivers/gpu/drm/bridge/ps8622.c:584: error: implicit declaration of function ‘devm_gpiod_get’
drivers/gpu/drm/bridge/ps8622.c:584: warning: assignment makes pointer from integer without a cast
drivers/gpu/drm/bridge/ps8622.c:590: error: implicit declaration of function ‘gpiod_direction_output’
drivers/gpu/drm/bridge/ps8622.c:596: warning: assignment makes pointer from integer without a cast
Add the missing #include <linux/gpio/consumer.h> to fix this.
Fixes: f1336e6afb ("drm/bridge: Add I2C based driver for ps8622/ps8625 bridge")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
If GPIOLIB=n and asm-generic/gpio.h is not used:
drivers/gpu/drm/bridge/ptn3460.c: In function ‘ptn3460_pre_enable’:
drivers/gpu/drm/bridge/ptn3460.c:135: error: implicit declaration of function ‘gpiod_set_value’
drivers/gpu/drm/bridge/ptn3460.c: In function ‘ptn3460_probe’:
drivers/gpu/drm/bridge/ptn3460.c:333: error: implicit declaration of function ‘devm_gpiod_get’
drivers/gpu/drm/bridge/ptn3460.c:333: warning: assignment makes pointer from integer without a cast
drivers/gpu/drm/bridge/ptn3460.c:340: error: implicit declaration of function ‘gpiod_direction_output’
drivers/gpu/drm/bridge/ptn3460.c:346: warning: assignment makes pointer from integer without a cast
Add the missing #include <linux/gpio/consumer.h> to fix this.
Fixes: af478d8823 ("drm/bridge: ptn3460: use gpiod interface")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
The dw_hdmi_connector_get_modes() function accidentally forgets to
return the number of modes it added, although it has this information
stored in a local variable. Let's fix that.
Without this fix, drm_helper_probe_single_connector_modes_merge_bits()
could get confused and always call drm_add_modes_noedid(). That's not
right.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Use this to simplify the driver. Furthermore this is one caller less
that stops us making the flags argument to gpiod_get*() mandatory.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Use this to simplify the driver. Furthermore this is one caller less
that stops us making the flags argument to gpiod_get*() mandatory.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
I2C drivers that support OF, have both an I2C and OF device ID tables
that are used to fill the supported module aliases. But currently the
I2C core only uses the OF table to match a device with a driver and
the aliases information are always reported in the form i2c:<name>.
The client->name is used as the name postfix and when booting with OF
this is obtained with of_modalias_node() which drops the compatible
string vendor prefix.
So for I2C drivers, the I2C and OF device ID tables should be keep in
sync in order to make module auto-loading to work but the I2C device
entries shouldn't have the vendor prefix since that is not reported.
Before this patch:
MODALIAS=i2c:ptn3460
$ modinfo | grep alias
alias: i2c:nxp,ptn3460
alias: of:N*T*Cnxp,ptn3460*
After this patch:
MODALIAS=i2c:ptn3460
$ modinfo | grep alias
alias: i2c:ptn3460
alias: of:N*T*Cnxp,ptn3460*
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Staticize dw_hdmi_bridge_funcs to fix the following sparse warning:
drivers/gpu/drm/bridge/dw_hdmi.c:1458:25: warning: symbol 'dw_hdmi_bridge_funcs' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This set of patches adjust the setup of the HDMI CTS/N values for audio
support to be compliant with the work-around given in the iMX6 errata
documentation as part of the preparation for integrating audio support
for this driver, and also update the HDMI phy configuration for Rockchip
devices to improve the HDMI eye pattern.
* 'drm-dwhdmi-devel' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm: rockchip/dw_hdmi-rockchip: improve for HDMI electrical test
drm: bridge/dw_hdmi: separate VLEVCTRL settting into platform driver
drm: bridge/dw_hdmi: fixed codec style
drm: bridge/dw_hdmi: adjust n/cts setting order
drm: bridge/dw_hdmi: protect n/cts setting with a mutex
drm: bridge/dw_hdmi: combine hdmi_set_clock_regenerator_n() and hdmi_regenerate_cts()
Conflicts:
drivers/gpu/drm/imx/dw_hdmi-imx.c
Because of iMX6 & Rockchip have differnet mpll config parameter,
the VLEVCTRL parameter would be different. In this case we should
separate VLEVCTRL setting from the common dw_hdmi driver, config
this parameter in platform driver(dw_hdmi-imx and dw_hdmi-rockchip)
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Using a local struct pointer to reduce one level of indirection
makes the code slightly more readable.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch derived from one from Yakir Yang. Yakir Yang says:
For Designerware HDMI, the following write sequence is recommended:
1. aud_n3 (set bit ncts_atomic_write if desired)
2. aud_cts3 (set CTS_manual and CTS value if desired/enabled)
3. aud_cts2 (required in CTS_manual)
4. aud_cts1 (required in CTS_manual)
5. aud_n3 (bit ncts_atomic_write with same value as in step 1.)
6. aud_n2
7. aud_n1
However, avoid the ncts_atomic_write_bit and CTS_manual settings in this
patch, both of which are marked reserved in the iMX6 documentation. All
iMX6 code in the wild seems to want CTS_manual cleared.
Having requested clarification from FSL, it appears that neither of
these bits are implemented in their version of the IP.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The HDMI n/cts settings need to be updated whenever the audio sample
rate or the video pixel clock changes. This needs to be protected
against concurrency as there is no synchronisation between these two
operations. Introduce a mutex (called audio_mutex) to protect against
two threads trying to update the video clock rate and pixel clock
simultaneously.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Combine these two functions into a single implementation. These two
functions are called consecutively anyway. Idea from a patch by
Yakir Yang.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ps8622_attach and ps8522_driver symbols are never used outside this
file, so they should be static.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit fbc4572e9c48e45b ("drm/bridge: make bridge registration independent of
drm flow") introduced some drm/bridge API modifications. Make the necessary
changes so that we can avoid the build breakage:
drivers/gpu/drm/bridge/dw_hdmi.c: In function 'dw_hdmi_bridge_destroy':
drivers/gpu/drm/bridge/dw_hdmi.c:1378:2: error: implicit declaration of function 'drm_bridge_cleanup' [-Werror=implicit-function-declaration]
drivers/gpu/drm/bridge/dw_hdmi.c: At top level:
drivers/gpu/drm/bridge/dw_hdmi.c:1471:2: error: unknown field 'destroy' specified in initializer
drivers/gpu/drm/bridge/dw_hdmi.c: In function 'dw_hdmi_register':
drivers/gpu/drm/bridge/dw_hdmi.c:1535:2: error: implicit declaration of function 'drm_bridge_init' [-Werror=implicit-function-declaration]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
If devm_request_threaded_irq() fails we should jump to 'err_iahb' label that
will disable the clocks that were previously enabled.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Force bridge connector detection at the end of the bridge attach.
This is needed to detect the bridge connector early.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add drm_panel calls to the driver to make the panel and
bridge work together in tandem.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently, third party bridge drivers(ptn3460) are dependent
on the corresponding encoder driver init, since bridge driver
needs a drm_device pointer to finish drm initializations.
The encoder driver passes the drm_device pointer to the
bridge driver. Because of this dependency, third party drivers
like ptn3460 doesn't adhere to the driver model.
In this patch, we reframe the bridge registration framework
so that bridge initialization is split into 2 steps, and
bridge registration happens independent of drm flow:
--Step 1: gather all the bridge settings independent of drm and
add the bridge onto a global list of bridges.
--Step 2: when the encoder driver is probed, call drm_bridge_attach
for the corresponding bridge so that the bridge receives
drm_device pointer and continues with connector and other
drm initializations.
The old set of bridge helpers are removed, and a set of new helpers
are added to accomplish the 2 step initialization.
The bridge devices register themselves onto global list of bridges
when they get probed by calling "drm_bridge_add".
The parent encoder driver waits till the bridge is available
in the lookup table(by calling "of_drm_find_bridge") and then
continues with its initialization.
The encoder driver should also call "drm_bridge_attach" to pass
on the drm_device to the bridge object.
drm_bridge_attach inturn calls "bridge->funcs->attach" so that
bridge can continue with drm related initializations.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Assign the pointer to bridge ops structure(drm_bridge_funcs) in
the bridge driver itself, instead of passing it to drm_bridge_init.
This will allow bridge driver developer to pack bridge private
information inside the bridge object and pass only the drm-relevant
information to drm_bridge_init.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch does the following changes:
-- Use usleep_range instead of udelay.
-- Remove driver_private member from ptn3460 structure.
-- Make all possible functions and structures static.
-- Use dev_err for non-DRM errors.
-- Arrange header files alphabetically.
-- s/edid/EDID in all error messages.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The encoder ->prepare() and ->mode_set() methods need to use the
hw adjusted mode, not the original mode.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Otherwise a spurious interrupt might trigger (and crash) the interrupt handler
before probing finished.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Rockchip RK3288 hdmi is compatible with dw_hdmi
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
RK3288 HDMI will not work without the spare bit of
HDMI_PHY_CONF0 enable
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
HDMI_IH_I2CMPHY_STAT0 is a clear on write register, which indicates i2cm
operation status(i2c transfer done or error), every hdmi phy register
configuration must check this register to make sure the configuration
has complete. But the indication bit should be cleared after check, otherwise
the corresponding bit will hold on forever, this may give a wrong signal for
next check.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
some platform may not support all the display mode,
add mode_valid interface check it
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
On rockchip rk3288, only word(32-bit) accesses are
permitted for hdmi registers. Byte width accesses (writeb,
readb) generate an imprecise external abort.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
the original imx hdmi driver is under drm/imx/,
which depends on imx-drm, so move the imx hdmi
driver out to drm/bridge and rename it to dw_hdmi
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Introduce generic functions to register and unregister connectors. This
provides a common place to add and remove associated user space
interfaces.
Signed-off-by: Thomas Wood <thomas.wood@intel.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Many drm connectors do not need mode validation.
The patch makes this callback optional and removes dumb implementations.
v2: Rebase:
- imx move to a shared (but still dummy) ->mode_valid implementation.
- probe helpers have been extracted to drm_probe_helper.c
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch exports ptn3460_init function so that other modules
can call this function.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The recently added PTN3460 device driver uses interfaces that
are provided by the KMS helper infrastructure, so we should
explicitly select that to avoid this linker error:
ERROR: "drm_helper_probe_single_connector_modes" [drivers/gpu/drm/bridge/ptn3460.ko] undefined!
ERROR: "drm_helper_connector_dpms" [drivers/gpu/drm/bridge/ptn3460.ko] undefined!
We have to drop the I2C dependency to avoid a circular dependency
chain, but that's ok because DRM already selects I2C.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch adds a drm_bridge driver for the PTN3460 DisplayPort to LVDS
bridge chip.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
