[why]
As a fail-safe, in case 'set FEC_READY' DPCD write fails, a HW shadow
register should be cleared and the internal FEC stat should be set to
'not ready'. This is to make sure HW settings will be consistent with
FEC_READY state on the RX.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Chris Park <Chris.Park@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
1. Stack usage is pretty high as fixed31_32 struct is 8 bytes and we
have functions with >30 vars on the stack.
2. Optimize gamma calculation by reducing number of calls to
dc_fixpt_pow Our X points are divided into 32 regions wth 16 pts each.
Each region is 2x the previous, meaning x[i] = 2*x[i-16] for i>=16.
Using (2x)^gamma = 2^gamma * x^gamma, we can recursively compute powers
of gamma, we just need first 16 pts to start it up. dc_fixpt_pow() is
expensive, it computes x^y by doing exp(y*logx) Exp is done by Taylor
series approximation, and log by Newton-like approximation that also
uses exp internally. In short, it's significantly heavier than
run-of-the-mill addition/subtraction/multiply.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Seamless boot optimization removed proper front end power off sequence.
In driver disable enable case, this causes driver to power gate hubp
and dpp while there is still memory fetching going on, this can cause
invalid memory requests to be generated which will hang data fabric.
[How]
Put back proper front end power off sequence
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Right now we FEC_READY is set only before the final link training,
i.e. at mode set time. This means FEC_READY won't be set when doing
link training as a response to HPD. It also fails UCD400 FEC test in
DP compliance.
[how]
Move FEC_READY setup to link training.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Abdoulaye Berthe <Abdoulaye.Berthe@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use helper to determine if HDMI signal when processing avmute.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Logic & structures for generic regs does not exist in DC currently.
[How]
Implement register masks/shifts and relevant functions for generic mux,
similar to existing HPD and DDC objects.
V2: fix includes for kalloc/free (Alex)
Signed-off-by: Murton Liu <murton.liu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In pipe split issue occurs when we program immediate flip while vsync flip is pending
[how]
Don't program immediate flip until flip is no longer pending
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jaehyun Chung <Jaehyun.Chung@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some display's hsync width is lower than the minimum dcn20 is set
to support right now. This will cause optc1_validate_timing to fail which
eventually will result in wrong set mode. This was set to 8 as per
HW team's request for no valid reason.
[How]
Changing min_h_sync_width to 4 will let us validate timing for
preffered mode and light up the headset. This change was made
to Vega 10 before for a similar issue.
Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
We initialize pp_smu twice
[how]
Remove second initialization of pp_smu
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jaehyun Chung <Jaehyun.Chung@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
dcn20_clk_mgr_construct was not initializing pp_smu, and PME call gets
filtered out by the null check
[how]
initialize pp_smu dcn20_clk_mgr_construct
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On some platforms, the encoder id 3 is not populated. So the encoders
are not stored in right order as index (id: 0, 1, 2, 4, 5) at pool. This
would cause encoders id 4 & id 5 to fail when finding corresponding
audio device, defaulting to the first available audio device. As result,
we cannot stream audio into two DP ports with encoders id 4 & id 5.
[How]
It need to create enough audio device objects (0 - 5) to perform matching.
Then use encoder engine id to find matched audio device.
Signed-off-by: Tai Man <taiman.wong@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
link_stream is never NULL here as we've dereferenced it a couple lines before
and have done so for a couple months now.
[How]
- Drop the NULL check.
- Initialize where we know link_stream is non-NULL
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
Do not fill Null packet in the blank period for new packet gen
This is based on HW IP team recommended default setting change.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When the system is going into suspend, set_backlight gets called
after the eDP got blanked. Since smooth brightness is enabled,
the driver will make a call into the DMCU to ramp the brightness.
The DMCU would try to enable ABM to do so. But since the display is
blanked, this ends up causing ABM1_ACE_DBUF_REG_UPDATE_PENDING to
get stuck at 1, which results in a dead lock in the DMCU firmware.
[how]
Disable brightness ramping when the eDP display is blanked.
Signed-off-by: Zi Yu Liao <ziyu.liao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When we recover from hang, we do not want to skip the audio enable call.
[How]
Disable audio in dc_reinitialize_hardware
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DSC should be powered-on only on as-needed basis, i.e. if the mode
requires it
[how]
Loop over all the DSCs at driver init time and power-gate each
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Current default is sufficient for a flag that does not change.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When launch D10.2, driver will write DPCD 0x107 with 0x00
[How]
Read MAX_DOWNSPREAD (0x0003h) then keep in current
link settings
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A hubp pointer was being passed to DCN1 functions, which
expect the enclosing structure (for the purpose of container_of macros)
to be dcn10_hubp, but the actual type was dcn20_hubp.
[How]
Copy existing DCN1 functions and alter them slightly for use with
dcn20_hubp.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Before accessing it's vtable, check that stream_encoder is non-null.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need to implement register programming for HDR dynamic
metadata transmission and tests.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently we don't wait for blacklight programming completion in DMCU
when setting backlight level. Some sequences such as PSR static screen
event trigger reprogramming requires it to be complete.
[How]
Add generic wait for dmcu command completion in set backlight level.
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to check the pipe crc source through debugfs for bypass mode test.
[How]
add implementation of amdgpu_dm_crtc_get_crc_sources and hook into drm_crtc
callback get_crc_sources.
Signed-off-by: Dingchen Zhang <dingchen.zhang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to compare DPRX CRCs with framebuffer CRCs for digital bypass mode.
[How]
Hook into DRM to grab DP receiver CRCs through drm_dp_start_crc.
Signed-off-by: Dingchen Zhang <dingchen.zhang@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hardware docs state that we must wait until the GPUVM context is ready
after programming it.
[How]
Poll until the valid bit of PAGE_TABLE_BASE_ADDR_LO32 is set to 1 after
programming it.
v2: fix include for udelay (Alex)
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Specifically to one panel,
TCON is able to accept active video signal quickly, but
the Source Driver requires 2-3 frames of extra time.
It is a Panel issue since TCON needs to take care of
all Sink requirements including Source Driver. But in
this case it does not.
Customer is asking to add fixed T7 delay as panel
workaround.
[How]
Add monitor specific patch to add T7 delay
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This change adds EMP packet programming for enabling dsc with
hdmi. The packets are structured according to VESA HDMI 2.1x
r2 spec, section 10.10.2.2.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
for 2 purposes:
1. get raw register value dumped on the log, which will make it easier
to talk to other team who only knows about the register
2. enable other HW to be able to use the same interface as raven to log
clock register data
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The current code will not wait for the entire frame
after global unlock.
This causes dsc dynamic target bpp update corruption when
there is a surface update immediately happens after this.
[how]
Wait for the entire whole frame after unlock before continuing
the rest of stream and surface update.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
-Pass and use pixel clock in 100 Hz to Audio for HDMI
audio DTO for Audio wall clock programming so audio DTO gets
increased precision for timings with /1001 factor.
-For HDMI TMDS for N and CTS ACR tables are based on 10 KHz
units, these does not need to be modified as N and CTS values
are still valid using current tables.
Signed-off-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For DCE110, DCE112 and DCE120 the max_clks_by_state for the clk_mgr are
copied from their respective table before the call to
dce_clk_mgr_construct, but then dce_clk_mgr_construct overwrites
these with the dce80_max_clks_by_state.
[How]
Copy these after we call dce_clk_mgr_construct so we're using the
right tables.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
We reset the optimized_required in atomic_plane_disable
flag immediately after it is set in atomic_plane_disconnect, causing us to
never have flag set during next flip in UpdatePlanes.
[how]
Optimize directly after each time plane is removed.
Signed-off-by: Murton Liu <murton.liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
TRAINING_AUX_RD_INTERVAL (DPCD 000Eh) modifies the read interval
for the EQ training sequence. CR read interval should remain 100 us.
Currently, the CR interval is also being modified.
[HOW]
lt_settings->cr_pattern_time should always be 100 us.
Signed-off-by: David Galiffi <david.galiffi@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are shared regs and code across DCN generations. Pull them out
into a shared common location.
Also, expose some dcn20 init functions.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Fixes issue when we have a display connected using a passive
dongle and then emulate over it using a DP connection at 1 x 1.62 Ghz.
System hangs because register bus returns back 0xFFFFFFFF for all
register reads after setting register DIG_BE_CNTL in
dcn10_link_encoder_connect_dig_be_to_fe(). Hang occurs later
when trying to do a register read.
[How]
At the start of the emulation, dc_link_set_preferred_link_settings()
and dp_retrain_link_dp_test() is called, even though it is connected
using a passive dongle.
Add an extra condition in dp_retrain_link_dp_test() to check for
link->dongle_max_pix_clk > 0. This is the only way we know if the
connection is using passive dongle so we don't retrain DP.
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Currently logical values are swapped in HW, causing
system aperture to be undefined, so VA and PA cannot co-exist
[how]
program values correctly
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
'second_line_offset_adj' was mistakenly left at zero, even though DSC spec
v1.2a recommends setting this field to 512 for 4:2:0.
[how]
Set 'second_line_offset_adj' to 512 for 4:2:0 and leave at zero otherwise
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We're not expected to enter the default case, but not returning a
default value here is incorrect.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Unintentionally introduced behaviour change from previous refactor,
which causes clks to be 0 in no stream cases, which will cause
divide by 0.
[How]
Skip calculation of clocks when no stream. Which is the same as old
behaviour.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <tong.cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some parts of the DSC spec relating to 4.2.0 were not reflected in
drm_dsc_compute_rc_parameters, causing unexpected config failures
[How]
Add nsl_bpg_offset and rbs_min computation
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dce was re-arch'd, therefore adding aux tracing log into new dce
[How]
The porting from submit_channel_request/process_channel_reply of aux_engine_dce110.c
Signed-off-by: Chiawen Huang <chiawen.huang@amd.com>
Reviewed-by: Tony Cheng <tong.cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are certain MST displays (i.e. Dell P2715Q)
that although have the MST feature set to off may still
report it is a branch device and a non-zero
value for downstream port present.
This can lead to us incorrectly classifying a
dp dongle connection as being active and
disabling the audio endpoint for the display.
[How]
Modified the placement and
condition used to assign
the is_branch_dev bit.
Signed-off-by: Harmanprit Tatla <harmanprit.tatla@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Due to limitation in SMU/PPLIB, it is not possible to know Fmax @ Vmin for DCFCLK.
This causes issues at high display configurations where extra headroom of DCFCLK
can enable P-state switching
[how]
Use existing override logic. If override not defined, then force
min = 507
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For better readability and reusability
[How]
Move snippets of BW calculation code into helpers.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Fatemeh Darbehani <Fatemeh.Darbehani@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A regression caused dsc to never get disabled in certain situations.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some values were not being converted or bit-shifted properly for
HW registers, causing black screen
[how]
Fix up the values before programming HW
Signed-off-by: Jun Lei <jun.lei@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
