x86 architecture defines differences between the reset and INIT sequences.
INIT does not initialize the FPU (including MMX, XMM, YMM, etc.), TSC, PMU,
MSRs (in general), MTRRs machine-check, APIC ID, APIC arbitration ID and BSP.
References (from Intel SDM):
"If the MP protocol has completed and a BSP is chosen, subsequent INITs (either
to a specific processor or system wide) do not cause the MP protocol to be
repeated." [8.4.2: MP Initialization Protocol Requirements and Restrictions]
[Table 9-1. IA-32 Processor States Following Power-up, Reset, or INIT]
"If the processor is reset by asserting the INIT# pin, the x87 FPU state is not
changed." [9.2: X87 FPU INITIALIZATION]
"The state of the local APIC following an INIT reset is the same as it is after
a power-up or hardware reset, except that the APIC ID and arbitration ID
registers are not affected." [10.4.7.3: Local APIC State After an INIT Reset
("Wait-for-SIPI" State)]
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Message-Id: <1428924848-28212-1-git-send-email-namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Introducing KVM_CAP_DISABLE_QUIRKS for disabling x86 quirks that were previous
created in order to overcome QEMU issues. Those issue were mostly result of
invalid VM BIOS. Currently there are two quirks that can be disabled:
1. KVM_QUIRK_LINT0_REENABLED - LINT0 was enabled after boot
2. KVM_QUIRK_CD_NW_CLEARED - CD and NW are cleared after boot
These two issues are already resolved in recent releases of QEMU, and would
therefore be disabled by QEMU.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Message-Id: <1428879221-29996-1-git-send-email-namit@cs.technion.ac.il>
[Report capability from KVM_CHECK_EXTENSION too. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use __kvm_guest_{enter|exit} instead of kvm_guest_{enter|exit}
where interrupts are disabled.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Several kvm architectures disable interrupts before kvm_guest_enter.
kvm_guest_enter then uses local_irq_save/restore to disable interrupts
again or for the first time. Lets provide underscore versions of
kvm_guest_{enter|exit} that assume being called locked.
kvm_guest_enter now disables interrupts for the full function and
thus we can remove the check for preemptible.
This patch then adopts s390/kvm to use local_irq_disable/enable calls
which are slighty cheaper that local_irq_save/restore and call these
new functions.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If you try to enable NOHZ_FULL on a guest today, you'll get
the following error when the guest tries to deactivate the
scheduler tick:
WARNING: CPU: 3 PID: 2182 at kernel/time/tick-sched.c:192 can_stop_full_tick+0xb9/0x290()
NO_HZ FULL will not work with unstable sched clock
CPU: 3 PID: 2182 Comm: kworker/3:1 Not tainted 4.0.0-10545-gb9bb6fb #204
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
Workqueue: events flush_to_ldisc
ffffffff8162a0c7 ffff88011f583e88 ffffffff814e6ba0 0000000000000002
ffff88011f583ed8 ffff88011f583ec8 ffffffff8104d095 ffff88011f583eb8
0000000000000000 0000000000000003 0000000000000001 0000000000000001
Call Trace:
<IRQ> [<ffffffff814e6ba0>] dump_stack+0x4f/0x7b
[<ffffffff8104d095>] warn_slowpath_common+0x85/0xc0
[<ffffffff8104d146>] warn_slowpath_fmt+0x46/0x50
[<ffffffff810bd2a9>] can_stop_full_tick+0xb9/0x290
[<ffffffff810bd9ed>] tick_nohz_irq_exit+0x8d/0xb0
[<ffffffff810511c5>] irq_exit+0xc5/0x130
[<ffffffff814f180a>] smp_apic_timer_interrupt+0x4a/0x60
[<ffffffff814eff5e>] apic_timer_interrupt+0x6e/0x80
<EOI> [<ffffffff814ee5d1>] ? _raw_spin_unlock_irqrestore+0x31/0x60
[<ffffffff8108bbc8>] __wake_up+0x48/0x60
[<ffffffff8134836c>] n_tty_receive_buf_common+0x49c/0xba0
[<ffffffff8134a6bf>] ? tty_ldisc_ref+0x1f/0x70
[<ffffffff81348a84>] n_tty_receive_buf2+0x14/0x20
[<ffffffff8134b390>] flush_to_ldisc+0xe0/0x120
[<ffffffff81064d05>] process_one_work+0x1d5/0x540
[<ffffffff81064c81>] ? process_one_work+0x151/0x540
[<ffffffff81065191>] worker_thread+0x121/0x470
[<ffffffff81065070>] ? process_one_work+0x540/0x540
[<ffffffff8106b4df>] kthread+0xef/0x110
[<ffffffff8106b3f0>] ? __kthread_parkme+0xa0/0xa0
[<ffffffff814ef4f2>] ret_from_fork+0x42/0x70
[<ffffffff8106b3f0>] ? __kthread_parkme+0xa0/0xa0
---[ end trace 06e3507544a38866 ]---
However, it turns out that kvmclock does provide a stable
sched_clock callback. So, let the scheduler know this which
in turn makes NOHZ_FULL work in the guest.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
for ext4 encryption which provide better security and performance.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJVRsVDAAoJEPL5WVaVDYGj/UUIAI6zLGhq3I8uQLZQC22Ew2Ph
TPj6eABDuTrB/7QpAu21Dk59N70MQpsBTES6yLWWLf/eHp0gsH7gCNY/C9185vOh
tQjzw18hRH2IfPftOBrjDlPGbbBD8Gu9jAmpm5kKKOtBuSVbKQ4GeN6BTECkgwlg
U5EJHJJ5Ahl4MalODFreOE5ZrVC7FWGEpc1y/MquQ0qcGSGlNd35leK5FE2bfHWZ
M1IJfXH5RRVPUBp26uNvzEg0TtpqkigmCJUT6gOVLfSYBw+lYEbGl4lCflrJmbgt
8EZh3Q0plsDbNhMzqSvOE4RvsOZ28oMjRNbzxkAaoz/FlatWX2hrfAoI2nqRrKg=
=Unbp
-----END PGP SIGNATURE-----
Merge tag 'for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Some miscellaneous bug fixes and some final on-disk and ABI changes
for ext4 encryption which provide better security and performance"
* tag 'for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix growing of tiny filesystems
ext4: move check under lock scope to close a race.
ext4: fix data corruption caused by unwritten and delayed extents
ext4 crypto: remove duplicated encryption mode definitions
ext4 crypto: do not select from EXT4_FS_ENCRYPTION
ext4 crypto: add padding to filenames before encrypting
ext4 crypto: simplify and speed up filename encryption
Pull drm fixes from Dave Airlie:
"One intel fix, one rockchip fix, and a bunch of radeon fixes for some
regressions from audio rework and vm stability"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915/chv: Implement WaDisableShadowRegForCpd
drm/radeon: fix userptr return value checking (v2)
drm/radeon: check new address before removing old one
drm/radeon: reset BOs address after clearing it.
drm/radeon: fix lockup when BOs aren't part of the VM on release
drm/radeon: add SI DPM quirk for Sapphire R9 270 Dual-X 2G GDDR5
drm/radeon: adjust pll when audio is not enabled
drm/radeon: only enable audio streams if the monitor supports it
drm/radeon: only mark audio as connected if the monitor supports it (v3)
drm/radeon/audio: don't enable packets until the end
drm/radeon: drop dce6_dp_enable
drm/radeon: fix ordering of AVI packet setup
drm/radeon: Use drm_calloc_ab for CS relocs
drm/rockchip: fix error check when getting irq
MAINTAINERS: add entry for Rockchip drm drivers
Just a single intel fix
* tag 'drm-intel-fixes-2015-04-30' of git://anongit.freedesktop.org/drm-intel:
drm/i915/chv: Implement WaDisableShadowRegForCpd
one fix and maintainers update
* 'drm-next0420' of https://github.com/markyzq/kernel-drm-rockchip:
drm/rockchip: fix error check when getting irq
MAINTAINERS: add entry for Rockchip drm drivers
This is three logical fixes (as 5 patches). The 3ware class of drivers were
causing an oops with multiqueue by tearing down the command mappings after
completing the command (where the variables in the command used to tear down
the mapping were no-longer valid). There's also a fix for the qnap iscsi
target which was choking on us sending it commands that were too long and a
fix for the reworked aha1542 allocating GFP_KERNEL under a lock.
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJVRkgEAAoJEDeqqVYsXL0MZbEIAL7Repky0TI1GvyYVpbJLSc+
SlJurEQ9DIpsnNtHJlEfLHicqsrK3v/xS+3Kopd1OUEIjQ0kTFPkenTiJbwFNIB+
l7D3V1EfEdnOki7F8KU5bFf3i4KWeEUZ4v/FR3PC7dz4cFRav7OrMoGaA36yT/ns
I4NFZ7iOa/6QXzfrywTDU5HbHgQYIN2MfCPy/NrVP95Yq09TkN5ulXDz/h6PD6Iy
GV/RmeckUqkdO5SZq9kkIgR/czLpVCaqpf3/G6lFdfunNkhQJ96lQTzYwbvtPBrJ
m6+sxrcCWlHzIkJsXrKtopPYzSzGdApLSsZjuYtP3RJD0uO9psfgW8pbls3dDCg=
=n4aD
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is three logical fixes (as 5 patches).
The 3ware class of drivers were causing an oops with multiqueue by
tearing down the command mappings after completing the command (where
the variables in the command used to tear down the mapping were
no-longer valid). There's also a fix for the qnap iscsi target which
was choking on us sending it commands that were too long and a fix for
the reworked aha1542 allocating GFP_KERNEL under a lock"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
3w-9xxx: fix command completion race
3w-xxxx: fix command completion race
3w-sas: fix command completion race
aha1542: Allocate memory before taking a lock
SCSI: add 1024 max sectors black list flag
Pull slave dmaengine fixes from Vinod Koul:
"Here are the fixes in dmaengine subsystem for rc2:
- privatecnt fix for slave dma request API by Christopher
- warn fix for PM ifdef in usb-dmac by Geert
- fix hardware dependency for xgene by Jean"
* 'next' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: increment privatecnt when using dma_get_any_slave_channel
dmaengine: xgene: Set hardware dependency
dmaengine: usb-dmac: Protect PM-only functions to kill warning
- Build fix for SMP=n in book3s_xics.c
- Fix for Daniel's pci_controller_ops on powernv.
- Revert the TM syscall abort patch for now.
- CPU affinity fix from Nathan.
- Two EEH fixes from Gavin.
- Fix for CR corruption from Sam.
- Selftest build fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=S0WU
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc fixes from Michael Ellerman:
- build fix for SMP=n in book3s_xics.c
- fix for Daniel's pci_controller_ops on powernv.
- revert the TM syscall abort patch for now.
- CPU affinity fix from Nathan.
- two EEH fixes from Gavin.
- fix for CR corruption from Sam.
- selftest build fix.
* tag 'powerpc-4.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc/powernv: Restore non-volatile CRs after nap
powerpc/eeh: Delay probing EEH device during hotplug
powerpc/eeh: Fix race condition in pcibios_set_pcie_reset_state()
powerpc/pseries: Correct cpu affinity for dlpar added cpus
selftests/powerpc: Fix the pmu install rule
Revert "powerpc/tm: Abort syscalls in active transactions"
powerpc/powernv: Fix early pci_controller_ops loading.
powerpc/kvm: Fix SMP=n build error in book3s_xics.c
The estimate of necessary transaction credits in ext4_flex_group_add()
is too pessimistic. It reserves credit for sb, resize inode, and resize
inode dindirect block for each group added in a flex group although they
are always the same block and thus it is enough to account them only
once. Also the number of modified GDT block is overestimated since we
fit EXT4_DESC_PER_BLOCK(sb) descriptors in one block.
Make the estimation more precise. That reduces number of requested
credits enough that we can grow 20 MB filesystem (which has 1 MB
journal, 79 reserved GDT blocks, and flex group size 16 by default).
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
fallocate() checks that the file is extent-based and returns
EOPNOTSUPP in case is not. Other tasks can convert from and to
indirect and extent so it's safe to check only after grabbing
the inode mutex.
Signed-off-by: Davide Italiano <dccitaliano@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
Currently it is possible to lose whole file system block worth of data
when we hit the specific interaction with unwritten and delayed extents
in status extent tree.
The problem is that when we insert delayed extent into extent status
tree the only way to get rid of it is when we write out delayed buffer.
However there is a limitation in the extent status tree implementation
so that when inserting unwritten extent should there be even a single
delayed block the whole unwritten extent would be marked as delayed.
At this point, there is no way to get rid of the delayed extents,
because there are no delayed buffers to write out. So when a we write
into said unwritten extent we will convert it to written, but it still
remains delayed.
When we try to write into that block later ext4_da_map_blocks() will set
the buffer new and delayed and map it to invalid block which causes
the rest of the block to be zeroed loosing already written data.
For now we can fix this by simply not allowing to set delayed status on
written extent in the extent status tree. Also add WARN_ON() to make
sure that we notice if this happens in the future.
This problem can be easily reproduced by running the following xfs_io.
xfs_io -f -c "pwrite -S 0xaa 4096 2048" \
-c "falloc 0 131072" \
-c "pwrite -S 0xbb 65536 2048" \
-c "fsync" /mnt/test/fff
echo 3 > /proc/sys/vm/drop_caches
xfs_io -c "pwrite -S 0xdd 67584 2048" /mnt/test/fff
This can be theoretically also reproduced by at random by running fsx,
but it's not very reliable, though on machines with bigger page size
(like ppc) this can be seen more often (especially xfstest generic/127)
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
This patch removes duplicated encryption modes which were already in
ext4.h. They were duplicated from commit 3edc18d and commit f542fb.
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Michael Halcrow <mhalcrow@google.com>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
This patch adds a tristate EXT4_ENCRYPTION to do the selections
for EXT4_FS_ENCRYPTION because selecting from a bool causes all
the selected options to be built-in, even if EXT4 itself is a
module.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Pull networking fixes from David Miller:
1) Receive packet length needs to be adjust by 2 on RX to accomodate
the two padding bytes in altera_tse driver. From Vlastimil Setka.
2) If rx frame is dropped due to out of memory in macb driver, we leave
the receive ring descriptors in an undefined state. From Punnaiah
Choudary Kalluri
3) Some netlink subsystems erroneously signal NLM_F_MULTI. That is
only for dumps. Fix from Nicolas Dichtel.
4) Fix mis-use of raw rt->rt_pmtu value in ipv4, one must always go via
the ipv4_mtu() helper. From Herbert Xu.
5) Fix null deref in bridge netfilter, and miscalculated lengths in
jump/goto nf_tables verdicts. From Florian Westphal.
6) Unhash ping sockets properly.
7) Software implementation of BPF divide did 64/32 rather than 64/64
bit divide. The JITs got it right. Fix from Alexei Starovoitov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (30 commits)
ipv4: Missing sk_nulls_node_init() in ping_unhash().
net: fec: Fix RGMII-ID mode
net/mlx4_en: Schedule napi when RX buffers allocation fails
netxen_nic: use spin_[un]lock_bh around tx_clean_lock
net/mlx4_core: Fix unaligned accesses
mlx4_en: Use correct loop cursor in error path.
cxgb4: Fix MC1 memory offset calculation
bnx2x: Delay during kdump load
net: Fix Kernel Panic in bonding driver debugfs file: rlb_hash_table
net: dsa: Fix scope of eeprom-length property
net: macb: Fix race condition in driver when Rx frame is dropped
hv_netvsc: Fix a bug in netvsc_start_xmit()
altera_tse: Correct rx packet length
mlx4: Fix tx ring affinity_mask creation
tipc: fix problem with parallel link synchronization mechanism
tipc: remove wrong use of NLM_F_MULTI
bridge/nl: remove wrong use of NLM_F_MULTI
bridge/mdb: remove wrong use of NLM_F_MULTI
net: sched: act_connmark: don't zap skb->nfct
trivial: net: systemport: bcmsysport.h: fix 0x0x prefix
...
Here the "other side" refers to the guest or host.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With my job change kernel work will be "own time"; I'm keeping lguest
and modules (and the virtio standards work), but virtio kernel has to
go.
This makes it clear that Michael is in charge. He's good, but having
me watch over his shoulder won't help.
Good luck Michael!
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull Ceph RBD fix from Sage Weil.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: end I/O the entire obj_request on error
If we don't do that, then the poison value is left in the ->pprev
backlink.
This can cause crashes if we do a disconnect, followed by a connect().
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Wen Xu <hotdog3645@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we end I/O struct request with error, we need to pass
obj_request->length as @nr_bytes so that the entire obj_request worth
of bytes is completed. Otherwise block layer ends up confused and we
trip on
rbd_assert(more ^ (which == img_request->obj_request_count));
in rbd_img_obj_callback() due to more being true no matter what. We
already do it in most cases but we are missing some, in particular
those where we don't even get a chance to submit any obj_requests, due
to an early -ENOMEM for example.
A number of obj_request->xferred assignments seem to be redundant but
I haven't touched any of obj_request->xferred stuff to keep this small
and isolated.
Cc: Alex Elder <elder@linaro.org>
Cc: stable@vger.kernel.org # 3.10+
Reported-by: Shawn Edwards <lesser.evil@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
This obscures the length of the filenames, to decrease the amount of
information leakage. By default, we pad the filenames to the next 4
byte boundaries. This costs nothing, since the directory entries are
aligned to 4 byte boundaries anyway. Filenames can also be padded to
8, 16, or 32 bytes, which will consume more directory space.
Change-Id: Ibb7a0fb76d2c48e2061240a709358ff40b14f322
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Avoid using SHA-1 when calculating the user-visible filename when the
encryption key is available, and avoid decrypting lots of filenames
when searching for a directory entry in a directory block.
Change-Id: If4655f144784978ba0305b597bfa1c8d7bb69e63
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Pull btrfs fixes from Chris Mason:
"A few more btrfs fixes.
These range from corners Filipe found in the new free space cache
writeback to a grab bag of fixes from the list"
* 'for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: btrfs_release_extent_buffer_page didn't free pages of dummy extent
Btrfs: fill ->last_trans for delayed inode in btrfs_fill_inode.
btrfs: unlock i_mutex after attempting to delete subvolume during send
btrfs: check io_ctl_prepare_pages return in __btrfs_write_out_cache
btrfs: fix race on ENOMEM in alloc_extent_buffer
btrfs: handle ENOMEM in btrfs_alloc_tree_block
Btrfs: fix find_free_dev_extent() malfunction in case device tree has hole
Btrfs: don't check for delalloc_bytes in cache_save_setup
Btrfs: fix deadlock when starting writeback of bg caches
Btrfs: fix race between start dirty bg cache writeout and bg deletion
- Fix perf devicetree warnings at probe time
- Fix memory leak in __dma_free()
- Ensure DMA buffers are always zeroed
- Show IRQ trigger in /proc/interrupts (for parity with ARM)
- Implement byte and halfword access for smp_{load_acquire,store_release}
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJVQlyfAAoJELescNyEwWM0ZTIIAKnK5bIr1jS9wP9wLJ8eZ++y
8p5RYluqtMBkYzbOpKr8HiJdg6GupNiSq6as+cf5T+Gc2D01HhFocqJbLrOCqJRA
RG5gFqkx/7FKTCwIt/DSygiwA+szPKTArf3YOi+EuDmCkcgRv38vac8yqlM1rI+M
UL2vdAEqvjPxPquzeAqrSIcwQ9jAYzEouh8VrMWigLFN5BvCUrO64r1y4zN7hbO1
RWEKPkIFMLDGCFwCn17mzLafVF2f0JH514sMZEQi2AQA/MlaIS3hM+SFJgxbRzib
ZRqXujX1Osi9W20VPwMtuUgQymEBQDAbXT35BxehL7MVMZhv66q+LBEabIpDMqM=
=4S7b
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Not too much here, but we've addressed a couple of nasty issues in the
dma-mapping code as well as adding the halfword and byte variants of
load_acquire/store_release following on from the CSD locking bug that
you fixed in the core.
- fix perf devicetree warnings at probe time
- fix memory leak in __dma_free()
- ensure DMA buffers are always zeroed
- show IRQ trigger in /proc/interrupts (for parity with ARM)
- implement byte and halfword access for smp_{load_acquire,store_release}"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: perf: Fix the pmu node name in warning message
arm64: perf: don't warn about missing interrupt-affinity property for PPIs
arm64: add missing PAGE_ALIGN() to __dma_free()
arm64: dma-mapping: always clear allocated buffers
ARM64: Enable CONFIG_GENERIC_IRQ_SHOW_LEVEL
arm64: add missing data types in smp_load_acquire/smp_store_release
Patches 7cba160ad "powernv/cpuidle: Redesign idle states management"
and 77b54e9f2 "powernv/powerpc: Add winkle support for offline cpus"
use non-volatile condition registers (cr2, cr3 and cr4) early in the system
reset interrupt handler (system_reset_pSeries()) before it has been determined
if state loss has occurred. If state loss has not occurred, control returns via
the power7_wakeup_noloss() path which does not restore those condition
registers, leaving them corrupted.
Fix this by restoring the condition registers in the power7_wakeup_noloss()
case.
This is apparent when running a KVM guest on hardware that does not
support winkle or sleep and the guest makes use of secondary threads. In
practice this means Power7 machines, though some early unreleased Power8
machines may also be susceptible.
The secondary CPUs are taken off line before the guest is started and
they call pnv_smp_cpu_kill_self(). This checks support for sleep
states (in this case there is no support) and power7_nap() is called.
When the CPU is woken, power7_nap() returns and because the CPU is
still off line, the main while loop executes again. The sleep states
support test is executed again, but because the tested values cannot
have changed, the compiler has optimized the test away and instead we
rely on the result of the first test, which has been left in cr3
and/or cr4. With the result overwritten, the wrong branch is taken and
power7_winkle() is called on a CPU that does not support it, leading
to it stalling.
Fixes: 7cba160ad7 ("powernv/cpuidle: Redesign idle states management")
Fixes: 77b54e9f21 ("powernv/powerpc: Add winkle support for offline cpus")
[mpe: Massage change log a bit more]
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 1c509148b ("powerpc/eeh: Do probe on pci_dn") probes EEH
devices in early stage, which is reasonable to pSeries platform.
However, it's wrong for PowerNV platform because the PE# isn't
determined until the resources (IO and MMIO) are assigned to
PE in hotplug case. So we have to delay probing EEH devices
for PowerNV platform until the PE# is assigned.
Fixes: ff57b454dd ("powerpc/eeh: Do probe on pci_dn")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When asserting reset in pcibios_set_pcie_reset_state(), the PE
is enforced to (hardware) frozen state in order to drop unexpected
PCI transactions (except PCI config read/write) automatically by
hardware during reset, which would cause recursive EEH error.
However, the (software) frozen state EEH_PE_ISOLATED is missed.
When users get 0xFF from PCI config or MMIO read, EEH_PE_ISOLATED
is set in PE state retrival backend. Unfortunately, nobody (the
reset handler or the EEH recovery functinality in host) will clear
EEH_PE_ISOLATED when the PE has been passed through to guest.
The patch sets and clears EEH_PE_ISOLATED properly during reset
in function pcibios_set_pcie_reset_state() to fix the issue.
Fixes: 28158cd ("Enhance pcibios_set_pcie_reset_state()")
Reported-by: Carol L. Soto <clsoto@us.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Tested-by: Carol L. Soto <clsoto@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The incorrect ordering of operations during cpu dlpar add results in invalid
affinity for the cpu being added. The ibm,associativity property in the
device tree is populated with all zeroes for the added cpu which results in
invalid affinity mappings and all cpus appear to belong to node 0.
This occurs because rtas configure-connector is called prior to making the
rtas set-indicator calls. Phyp does not assign affinity information
for a cpu until the rtas set-indicator calls are made to set the isolation
and allocation state.
Correct the order of operations to make the rtas set-indicator
calls (done in dlpar_acquire_drc) before calling rtas configure-connector.
Fixes: 1a8061c46c ("powerpc/pseries: Add kernel based CPU DLPAR handling")
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
My patch to add install support for the powerpc selftests had a typo,
leading to the three tests in the pmu directory itself not being
installed.
Fixes: 6faeeea44b ("selftests: Add install support for the powerpc tests")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- Fix for a regression in the cpuidle core introduced by one of
the recent commits in the clockevents_notify() removal series
that put a call to a function which had to be executed with
disabled interrupts into a code path running with enabled
interrupts (Rafael J Wysocki).
- Fix for a build problem in ACPICA (with GCC 4.5) introduced by one
of the recent ACPICA tools commits that added a duplicate typedef
to one of the ACPICA's header files by mistake (Olaf Hering).
- Fix for a regression in the ACPI SBS (Smart Battery Subsystem)
driver introduced during the 3.18 development cycle causing the
smart battery manager to be marked as not present when it should
be marked as present (Chris Bainbridge).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=v78a
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"Three regression fixes this time, one for a recent regression in the
cpuidle core affecting multiple systems, one for an inadvertently
added duplicate typedef in ACPICA that breaks compilation with GCC 4.5
and one for an ACPI Smart Battery Subsystem driver regression
introduced during the 3.18 cycle (stable-candidate).
Specifics:
- Fix for a regression in the cpuidle core introduced by one of the
recent commits in the clockevents_notify() removal series that put
a call to a function which had to be executed with disabled
interrupts into a code path running with enabled interrupts (Rafael
J Wysocki)
- Fix for a build problem in ACPICA (with GCC 4.5) introduced by one
of the recent ACPICA tools commits that added a duplicate typedef
to one of the ACPICA's header files by mistake (Olaf Hering)
- Fix for a regression in the ACPI SBS (Smart Battery Subsystem)
driver introduced during the 3.18 development cycle causing the
smart battery manager to be marked as not present when it should be
marked as present (Chris Bainbridge)"
* tag 'pm+acpi-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: Run tick_broadcast_exit() with disabled interrupts
ACPI / SBS: Enable battery manager when present
ACPICA: remove duplicate u8 typedef
One nice fix is Peter's patch to make the old good SB Audigy PCI to
work with 32bit DMA instead of 31bit. This allows the MIDI synth
running on modern machines again. Along with it, a few fixes for
emu10k1 have merged.
In ASoC side, there is one fix in the common code, but it's just
trivial additions of static inline functions for CONFIG_PM=n. The rest
are various device-specific small fixes.
Last but not least, a few HD-audio fixes are included, as usual, too.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Ao64
-----END PGP SIGNATURE-----
Merge tag 'sound-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"One nice fix is Peter's patch to make the old good SB Audigy PCI to
work with 32bit DMA instead of 31bit. This allows the MIDI synth
running on modern machines again. Along with it, a few fixes for
emu10k1 have merged.
In ASoC side, there is one fix in the common code, but it's just
trivial additions of static inline functions for CONFIG_PM=n. The
rest are various device-specific small fixes.
Last but not least, a few HD-audio fixes are included, as usual, too"
* tag 'sound-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (23 commits)
ASoC: rt5677: fixed wrong DMIC ref clock
ALSA: emu10k1: Emu10k2 32 bit DMA mode
ALSA: emux: Fix mutex deadlock in OSS emulation
ASoC: Update email-id of Rajeev Kumar
ASoC: rt5645: Fix mask for setting RT5645_DMIC_2_DP_GPIO12 bit
ALSA: hda - Fix missing va_end() call in snd_hda_codec_pcm_new()
ALSA: emux: Fix mutex deadlock at unloading
ALSA: emu10k1: Fix card shortname string buffer overflow
ALSA: hda - Add mute-LED mode control to Thinkpad
ALSA: hda - Fix mute-LED fixed mode
ALSA: hda - Fix click noise at start on Dell XPS13
ASoC: rt5645: Add ACPI match ID
ASoC: rt5677: add register patch for PLL
ASoC: Intel: fix the makefile for atom code
ASoC: dapm: Enable autodisable on SOC_DAPM_SINGLE_TLV_AUTODISABLE
ASoC: add static inline funcs to fix a compiling issue
ASoC: Intel: sst_byt: remove kfree for memory allocated with devm_kzalloc
ASoC: samsung: s3c24xx-i2s: Fix return value check in s3c24xx_iis_dev_probe()
ASoC: tfa9879: Fix return value check in tfa9879_i2c_probe()
ASoC: fsl_ssi: Fix platform_get_irq() error handling
...
RGMII-ID uses an internal delay within the transmitter or receiver. This
feature is phy specific. The rest of the communication is normal RGMII.
So the fec driver has to check for all RGMII modes, not only
'PHY_INTERFACE_MODE_RGMII'.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When system is out of memory, refilling of RX buffers fails while
the driver continue to pass the received packets to the kernel stack.
At some point, when all RX buffers deplete, driver may fall into a
sleep, and not recover when memory for new RX buffers is once again
availible. This is because hardware does not have valid descriptors,
so no interrupt will be generated for the driver to return to work
in napi context. Fix it by schedule the napi poll function from
stats_task delayed workqueue, as long as the allocations fail.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing this driver with DEBUG_LOCKDEP and DEBUG_SPINLOCK
enabled did not produce any traces, it would be more prudent in the
case of tx_clean_lock to use spin_[un]lock_bh, since this lock is
manipulated in both the process and softirq contexts.
This patch was tested for functionality and regressions with netperf
and DEBUG_LOCKDEP and DEBUG_SPINLOCK enabled.
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Addresses the following kernel logs seen during boot:
Kernel unaligned access at TPC[100ee150] mlx4_QUERY_HCA+0x80/0x248 [mlx4_core]
Kernel unaligned access at TPC[100f071c] mlx4_QUERY_ADAPTER+0x100/0x12c [mlx4_core]
Kernel unaligned access at TPC[100f071c] mlx4_QUERY_ADAPTER+0x100/0x12c [mlx4_core]
Kernel unaligned access at TPC[100f071c] mlx4_QUERY_ADAPTER+0x100/0x12c [mlx4_core]
Kernel unaligned access at TPC[100f071c] mlx4_QUERY_ADAPTER+0x100/0x12c [mlx4_core]
Signed-off-by: David Ahern <david.ahern@oracle.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Fixes: 9e311e7 ("net/mlx4_en: Use affinity hint")
Acked-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few fixes for v4.1, none earth shattering and mostly driver related
except for one change to fix !PM builds for Intel platforms which is
done by adding stubs in the core so other platforms don't run into the
same issue.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVQj3nAAoJECTWi3JdVIfQkxYH/R8MhnJl7eQbW88UBcIZiDI+
IeJ239r8AH6HJHA7BFOfG1gUYCmpLsY+1rssyrJXYiKBRNsQ/az7AV1iFx/He7Xg
+NS9wBmLyj4yMF0aHETg5j3qdba+bNJLmNe0hlydXnSk79twgBkTw1YPY2eQ+5xX
DMZaBk2SRnikb8R7vUgCjMfpB5HxcpPAo8z55FRJOAb4yYBERUx82GQ9aGqInQk1
5gbtwBPDQ4kZyJitBA5o9qRV0jcXx75iC/vM4nvwi2Vjp/tLsYlhuk0RuwH1SnJ/
lzjBau7kYo97wxTf4Z903EijkgwYuk9FhRusxNr/FaBZB7pDBAxjzwVWoxJUV3U=
=INCv
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.1
A few fixes for v4.1, none earth shattering and mostly driver related
except for one change to fix !PM builds for Intel platforms which is
done by adding stubs in the core so other platforms don't run into the
same issue.
pvclock read; instead use the correct protocol in KVM.
This removes the need for task migration notifiers in core
scheduler code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJVQkUWAAoJEL/70l94x66DhfcH/A8RTHUOELtoy+v2weahn21m
FFWEnEUlCWzYgmiddgFdlr6+ub386W3ryFsXKPqjrn/8LVv3yS7tK1NJF8d03LQw
n7HtIsrF01E9UI8CIWO4S/mUxWQev6vEJ9NXtNrsJcRmhSeLaIZkPjTH8Zqyx4i9
ZvG4731WHXmxvbJ03bfJU9Y8OwHXe55GMi614aTxPndVBGdvIRu2Oj6aTfQTeab/
7tEujub0MKWp74a7eyNU4GItcvIAXZCQt2wMc5dN1VK3ma5FTOnHIOuhAb8mACFF
qEeGhtxAnOf7W+s9J8i7zVBdA5MOS0vUKng361ZOVGDb0OLqcVADW7GpuTZfRAM=
=2A7v
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm changes from Paolo Bonzini:
"Remove from guest code the handling of task migration during a pvclock
read; instead use the correct protocol in KVM.
This removes the need for task migration notifiers in core scheduler
code"
[ The scheduler people really hated the migration notifiers, so this was
kind of required - Linus ]
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
x86: pvclock: Really remove the sched notifier for cross-cpu migrations
kvm: x86: fix kvmclock update protocol
the 4.1 merge.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVQjzSAAoJEMUj8QotnQNaxOwIAJceb8ih3QGT5+2dcO2lZ0K7
NZfNvLgJQswg36vvjuLn8rrMXcAnmLSa+aEFrFH5coeGIYAMWaJqA+4vtohQPZPh
POSGIFkJxtpmWHqLlEZWthCMlZfoC3GhTu+BEWMcryupZpsJaLhiwBsWdA4HoMaE
tASn1qYK3y3ttFdnqRtfeKE0WFIZrmrEfR+tCMAqkrIEqnwLAY09KHCFHIf8tZjE
Lg4pOJPAPqxdFZ2vvWPj0671VQVfwuN08iqyemk6jWk3SD9GiB1faezFjXt4Lkgz
0kqXnkBgBsewheMLH55GgiRYg6ijCDzt55l6NLu0r2ltkSKX3z1qr5zhy/lIjRY=
=eV73
-----END PGP SIGNATURE-----
Merge tag 'dm-4.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper bugfixes from Mike Snitzer:
"Fix two bugs in the request-based DM blk-mq support that was added
during the 4.1 merge"
* tag 'dm-4.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: fix free_rq_clone() NULL pointer when requeueing unmapped request
dm: only initialize the request_queue once
Change default key details to be more obviously unspecified.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here are some small tty/serial driver fixes for 4.1-rc2.
They include some minor fixes that resolve reported issues, and a new
device quirk.
All have been in linux-next succesfully.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlVCMgMACgkQMUfUDdst+ylmRwCgzADm9JPmMS7DX0g21mfVSeQK
nI0AoIiYm3HHxu7wma7o3DowGLvuScwt
=8lGO
-----END PGP SIGNATURE-----
Merge tag 'tty-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small tty/serial driver fixes for 4.1-rc2.
They include some minor fixes that resolve reported issues, and a new
device quirk.
All have been in linux-next succesfully"
* tag 'tty-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: 8250_pci: Add support for 16 port Exar boards
serial: samsung: fix serial console break
tty/serial: at91: maxburst was missing for dma transfers
serial: of-serial: Remove device_type = "serial" registration
serial: xilinx: Use platform_get_irq to get irq description structure
serial: core: Fix kernel-doc build warnings
tty: Re-add external interface for tty_set_termios()
Here are a number of small USB fixes for 4.2-rc2. They revert one
problem patch, fix some minor things, and add some new quirks for
"broken" devices.
All have been in linux-next successfully.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlVCMNMACgkQMUfUDdst+ylQJwCgsGHQVK4YgrIOCpIkXoc+riy1
VWkAnip86mUGKRej4jrrRvTGvm3maeTj
=/oWf
-----END PGP SIGNATURE-----
Merge tag 'usb-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB fixes for 4.2-rc2. They revert one
problem patch, fix some minor things, and add some new quirks for
"broken" devices.
All have been in linux-next successfully"
* tag 'usb-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
cdc-acm: prevent infinite loop when parsing CDC headers.
Revert "usb: host: ehci-msm: Use devm_ioremap_resource instead of devm_ioremap"
usb: chipidea: otg: remove mutex unlock and lock while stop and start role
uas: Set max_sectors_240 quirk for ASM1053 devices
uas: Add US_FL_MAX_SECTORS_240 flag
uas: Allow uas_use_uas_driver to return usb-storage flags
* Remove test for now unsupported sh7372 SoC
* Disable PM runtime for multi-platform r8a73a4 and sh73a0 SoCs with genpd
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jOnx
-----END PGP SIGNATURE-----
Merge tag 'renesas-sh-drivers-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas
Pull SH driver updates from Simon Horman:
- remove test for now unsupported sh7372 SoC
- disable PM runtime for multi-platform r8a73a4 and sh73a0 SoCs with
genpd
* tag 'renesas-sh-drivers-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
drivers: sh: Remove test for now unsupported sh7372
drivers: sh: Disable PM runtime for multi-platform r8a73a4 with genpd
drivers: sh: Disable PM runtime for multi-platform sh73a0 with genpd
Commit 022333427a ("dm: optimize dm_mq_queue_rq to _not_ use kthread if
using pure blk-mq") mistakenly removed free_rq_clone()'s clone->q check
before testing clone->q->mq_ops. It was an oversight to discontinue
that check for 1 of the 2 use-cases for free_rq_clone():
1) free_rq_clone() called when an unmapped original request is requeued
2) free_rq_clone() called in the request-based IO completion path
The clone->q check made sense for case #1 but not for #2. However, we
cannot just reinstate the check as it'd mask a serious bug in the IO
completion case #2 -- no in-flight request should have an uninitialized
request_queue (basic block layer refcounting _should_ ensure this).
The NULL pointer seen for case #1 is detailed here:
https://www.redhat.com/archives/dm-devel/2015-April/msg00160.html
Fix this free_rq_clone() NULL pointer by simply checking if the
mapped_device's type is DM_TYPE_MQ_REQUEST_BASED (clone's queue is
blk-mq) rather than checking clone->q->mq_ops. This avoids the need to
dereference clone->q, but a WARN_ON_ONCE is added to let us know if an
uninitialized clone request is being completed.
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
