The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* beacon support for USB devices (mesh+ad-hoc only)
* mt76x0 tx power fixes
* fixes for encryption, calibration and ED/CCA
* more code unification
* USB fixes
* fix for using the correct hweight8 function
-----BEGIN PGP SIGNATURE-----
Version: GnuPG/MacGPG2 v2
Comment: GPGTools - http://gpgtools.org
iEYEABECAAYFAlxrEukACgkQ130UHQKnbvVuLgCg1hCXwfcaOFrDWv320hnBO5by
uacAn31lce0BEU3+O7cCof2UXcoH+HA+
=Iqux
-----END PGP SIGNATURE-----
Merge tag 'mt76-for-kvalo-2019-02-18' of https://github.com/nbd168/wireless
mt76 patches for 5.1
* beacon support for USB devices (mesh+ad-hoc only)
* mt76x0 tx power fixes
* fixes for encryption, calibration and ED/CCA
* more code unification
* USB fixes
* fix for using the correct hweight8 function
It needs to be unset instead of set
Fixes: 2340523646 ("mt76: fix transmission of encrypted management frames")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since ccmp_pn is u8 *, the second half needs to start at array index 4
instead of 0. Fixes a connection stall after a certain amount of traffic
Fixes: 2340523646 ("mt76: fix transmission of encrypted management frames")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove bogus check for MT_PACKET_ID_NO_ACK in mt76_tx_status_skb_get, which
is already handled in callers and turns timeout calls into no-ops
Do not clean up pending status items on reordering of tx status information
if the timeout is not reached yet
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt76_init_stream_cap() and mt76_get_txpower() call __sw_hweight8()
directly, but that's only defined if CONFIG_GENERIC_HWEIGHT is
enabled. The function that works on all architectures is hweight8().
Fixes: 551e1ef4d2 ("mt76: add mt76_init_stream_cap routine")
Fixes: 9313faacbb ("mt76: move mt76x02_get_txpower to mt76 core")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In mt76x02u_skb_dma_info() pad is always non-zero. Patch removes
bogus check and add comments to the function.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
During device removal the driver can report multiple error messages.
Use dev_err_ratelimited instead of dev_err to display urb errors
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add disable_usb_sg module parameter to disable scatter-gather on demand
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use linear fragment and not a single usb scatter-gather buffer in mt76u
{tx,rx} datapath if the usb controller has sg data length constraints
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do not use scatter-gather buffers for mcu commands.
Introduce mt76u_buf_alloc and mt76u_buf_alloc_sg routines.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76u_check_sg routine in usb.c and introduce sg_en variable
in mt76_usb in order to check if scatter-gather is supported by
mt76u layer
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move q->ndesc initialization before the for loop in mt76u_alloc_rx
since otherwise allocated urbs will not be freed in mt76u_buf_free
Double-check scatterlist pointer in mt76u_buf_free
Fixes: b40b15e152 ("mt76: add usb support to mt76 layer")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix possible NULL pointer dereference in mt76u_mcu_deinit routine that
can occur if initialization path fails before calling mt76u_mcu_init_rx
Fixes: ee676cd501 ("mt76: add driver code for MT76x2u based devices")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We don't need to send firmware data asynchronously, much simpler is just
use synchronous usb_bulk_msg().
Tested-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76x0_init_txpower in order to initialize max_power per channel
at device bootstrap. Modify mt76x0_get_tx_power_per_rate and
mt76x0_get_power_info signature in order to compute tx power for
non-operating channels
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Initialize target_power variable in mt76x0_phy_set_txpower in order to
report target_power in debugfs
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There is no need to retun 0 in mt76_dma_attach(), so switch it to void.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt76x2_alloc_device since it just runs mt76_alloc_device.
Move mt76_alloc_device call in mt76x2_probe
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt76x0u_alloc_device since it just runs mt76_alloc_device.
Move mt76_alloc_device call in mt76x0u_probe and in mt76x0e_probe
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt76x2u_alloc_device since it just runs mt76_alloc_device.
Move mt76_alloc_device call in mt76x2u_probe
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x{0,2} alloc_device common code in mt76_alloc_device and
remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Block only when the busy time reaches 92%, as lower values can be reached with
heavy 802.11 traffic as well.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Based on system load and time needed by other calibration runs, the time
between dev->mac_work runs can vary quite a bit.
Calculate busy time based on the actual time difference in order to avoid
potentially over-estimating busy time, which could lead to unnecessary tx
blocking.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
ED/CCA Tx blocking checks need to be run every 100 ms in order to avoid
triggering too late and keeping tx blocking on for too long
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Software encrypted packets can be passed not just through the drv_tx callback,
but also through the intermediate tx queue.
In order to deal with that, move the override to mt76x02_mac_write_txwi and
also take care of filling in the per-packet rate information
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove add_buf function pointer in mt76_queue_ops data structure since
it is no longer used
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_dma_tx_queue_skb_raw routine in dma.c and add the
corresponding entry in mt76_queue_ops data structure.
mt76_dma_tx_queue_skb_raw will be reused adding support for
mt7603 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove useless commented out configuration in mt76x0u_load_firmware
routine
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_mcu_rx_event i mt76-core module and remove duplicated code.
mt76_mcu_rx_event will be reused adding support for mt7603 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_mcu_get_response in mt76-core module and remove duplicated
code. mt76_mcu_get_response will be reused adding support for mt7603
driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_mcu_msg_alloc in mt76-core module and remove duplicated code.
mt76_mcu_msg_alloc will be reused adding support for mt7603 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix rate power configuration for VHT mcs 8 and 9 in
mt76x0_get_tx_power_per_rate. Moreover use the rate power
offset used for HT/VHT mcs 6 even for HT/VHT mcs 7
Fixes: b37bbc8c82 ("mt76x0: remove eeprom dependency from mt76x0_set_tx_power_per_rate")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since we implement beconing on USB now, similar interfaces should be
supported for USB as are for MMIO. Tested only on IBSS mode and
AP mode (not enabled due to lack of PS buffering).
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Configure beaconing on USB devices without PS buffering support.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Disable BEACON timer during init and configure interrupt registers
only for mmio devices.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
BSSID is not strtirct related with beaconing (for example we can have
2 STA vifs) and more related with MAC address, so initaize BSSID when
setting MAC address.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since we now support mt76x2u feature to allow set mac address
when creating interface in common code we can use it for
mt76x2u.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use vif_mask to count interfaces to allow to set mac address in HW
if there is only one interface and report error if we create
interface with wrong BSSID resulting in already used index.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
* Work on the new debugging infrastructure continues;
* FTM (Fine Timing Measurement) initiator and responder implementation;
* Support for a new device family started;
* Bump supported FW API to 46;
* General bugfixes;
* Other cleanups;
-----BEGIN PGP SIGNATURE-----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=B8hU
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2019-02-14' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Fourth batch of iwlwifi patches intended for v5.1
* Work on the new debugging infrastructure continues;
* FTM (Fine Timing Measurement) initiator and responder implementation;
* Support for a new device family started;
* Bump supported FW API to 46;
* General bugfixes;
* Other cleanups;
AP interfaces still use some static TX queues (for probes,
broadcast and multicast frames). These queues were not stopped
correctly when the transport layer indicated the queue should be
stopped. As a result, when flushing the queues, new frames from
the overflow queue were tx'd, so the queues still had frames after
flushing. This ended up in an assert since trying to remove a station
with non-empty queues.
Fix it by stopping the static queues correctly when required.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add IWL_FW_INI_APPLY_EARLY and IWL_FW_INI_APPLY_AFTER_ALIVE apply points
to unified images.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When HW restart is requested but not started yet, commands would not
be sent to the FW, and some function calls would return an error. In
case of iwl_mvm_mac_sta_state() returning an error value when a
station is removed can lead to an unneeded warning in
__sta_info_destroy_part2().
Handle this by setting the return value to 0, in case HW restart is
in progress.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When HW restart is requested but not started yet, commands would not
be sent to the FW, and some function calls return an error. Such cases
can trigger unneeded warning messages, e.g., in iwl_mvm_mac_sta_state()
and iwl_mvm_bss_info_changed_station().
Handle a couple of these cases by also checking in the WARN_ON()
condition that HW restart is not requested.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
