The CANFD transmitter delay calculation formula was updated in the
latest software drop from IFI and improves the behavior of the IFI
CANFD core during bitrate switching. Use the new formula to improve
stability of the CANFD operation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Markus Marb <markus@marb.org>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This adds support for the following PEAK-System CAN FD interfaces:
PCAN-cPCIe FD CAN FD Interface for cPCI Serial (2 or 4 channels)
PCAN-PCIe/104-Express CAN FD Interface for PCIe/104-Express (1, 2 or 4 ch.)
PCAN-miniPCIe FD CAN FD Interface for PCIe Mini (1, 2 or 4 channels)
PCAN-PCIe FD OEM CAN FD Interface for PCIe OEM version (1, 2 or 4 ch.)
PCAN-M.2 CAN FD Interface for M.2 (1 or 2 channels)
Like the PCAN-PCIe FD interface, all of these boards run the same IP Core
that is able to handle CAN FD (see also http://www.peak-system.com).
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
SUN4Is CAN IP has a 64 byte deep FIFO buffer. If the buffer is not
drained fast enough (overrun) it's getting mangled. Already received
frames are dropped - the data can't be restored.
Signed-off-by: Gerhard Bertelsmann <info@gerhard-bertelsmann.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The D_CAN controller doesn't provide a triple sampling mode, so don't set
the CAN_CTRLMODE_3_SAMPLES flag in ctrlmode_supported. Currently enabling
triple sampling is a no-op.
Signed-off-by: Richard Schütz <rschuetz@uni-koblenz.de>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.6
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several conflicts here.
NFP driver bug fix adding nfp_netdev_is_nfp_repr() check to
nfp_fl_output() needed some adjustments because the code block is in
an else block now.
Parallel additions to net/pkt_cls.h and net/sch_generic.h
A bug fix in __tcp_retransmit_skb() conflicted with some of
the rbtree changes in net-next.
The tc action RCU callback fixes in 'net' had some overlap with some
of the recent tcf_block reworking.
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Allen Pais <allen.lkml@gmail.com>
Cc: linux-can@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid kernel warning "Unhandled message (68)", ignore the
CMD_FLUSH_QUEUE_REPLY message for now.
As of Leaf v2 firmware version v4.1.844 (2017-02-15), flush tx queue is
synchronous. There is a capability bit indicating whether flushing tx
queue is synchronous or asynchronous.
A proper solution would be to query the device for capabilities. If the
synchronous tx flush capability bit is set, we should wait for
CMD_FLUSH_QUEUE_REPLY message, while flushing the tx queue.
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the return value from kvaser_usb_send_simple_msg() was non-zero, the
return value from kvaser_usb_flush_queue() was printed in the kernel
warning.
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fix loopback mode by setting the right flag and remove presume mode.
Signed-off-by: Gerhard Bertelsmann <info@gerhard-bertelsmann.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There were quite a few overlapping sets of changes here.
Daniel's bug fix for off-by-ones in the new BPF branch instructions,
along with the added allowances for "data_end > ptr + x" forms
collided with the metadata additions.
Along with those three changes came veritifer test cases, which in
their final form I tried to group together properly. If I had just
trimmed GIT's conflict tags as-is, this would have split up the
meta tests unnecessarily.
In the socketmap code, a set of preemption disabling changes
overlapped with the rename of bpf_compute_data_end() to
bpf_compute_data_pointers().
Changes were made to the mv88e6060.c driver set addr method
which got removed in net-next.
The hyperv transport socket layer had a locking change in 'net'
which overlapped with a change of socket state macro usage
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
If sending messages with no cable connected, it quickly happens that
there is no more TX context available. Then "gs_can_start_xmit()"
returns with "NETDEV_TX_BUSY" and the upper layer does retry
immediately keeping the CPU busy. To fix that issue, I moved
"atomic_dec(&dev->active_tx_urbs)" from "gs_usb_xmit_callback()" to
the TX done handling in "gs_usb_receive_bulk_callback()". Renaming
"active_tx_urbs" to "active_tx_contexts" and moving it into
"gs_[alloc|free]_tx_context()" would also make sense.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The dlc member of the struct rx_msg contains also the ESD_RTR flag to
mark received RTR frames. Without the fix the can_dlc value for received
RTR frames would always be set to 8 by get_can_dlc() instead of the
received value.
Fixes: 96d8e90382 ("can: Add driver for esd CAN-USB/2 device")
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Enable FLEXCAN_QUIRK_BROKEN_WERR_STATE and
FLEXCAN_QUIRK_BROKEN_PERR_STATE for p1010 to report correct state
transitions.
Signed-off-by: Zhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Enable FLEXCAN_QUIRK_BROKEN_PERR_STATE for i.MX28 to report correct
state transitions, especially to error passive.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Zhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Enable FLEXCAN_QUIRK_BROKEN_PERR_STATE for i.MX6 to report correct state
transitions.
Signed-off-by: Zhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add FLEXCAN_QUIRK_BROKEN_PERR_STATE for better description of the
missing error passive interrupt quirk.
Error interrupt flooding may happen if the broken error state quirk fix
is enabled. For example, in case there is singled out node on the bus
and the node sends a frame, then error interrupt flooding happens and
will not stop because the node cannot go to bus off. The flooding will
stop after another node connected to the bus again.
If high bitrate configured on the low end system, then the flooding
may causes performance issue, hence, this patch mitigates this by:
1. disable error interrupt upon error passive state transition
2. re-enable error interrupt upon error warning state transition
3. disable/enable error interrupt upon error active state transition
depends on FLEXCAN_QUIRK_BROKEN_WERR_STATE
In this way, the driver is still able to report correct state
transitions without additional latency. When there are bus problems,
flooding of error interrupts is limited to the number of frames required
to change state from error warning to error passive if the core has
[TR]WRN_INT connected (FLEXCAN_QUIRK_BROKEN_WERR_STATE is not enabled),
otherwise, the flooding is limited to the number of frames required to
change state from error active to error passive.
Signed-off-by: Zhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Rename FLEXCAN_QUIRK_BROKEN_ERR_STATE to FLEXCAN_QUIRK_BROKEN_WERR_STATE
for better description of the missing [TR]WRN_INT quirk.
Signed-off-by: Zhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Update state upon any interrupt to report correct state transitions in
case the flexcan core enabled the broken error state quirk fix.
Signed-off-by: Zhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
platform_device_id are not supposed to change at runtime. All functions
working with platform_device_id provided by <linux/platform_device.h>
work with const platform_device_id. So mark the non-const structs as
const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/netdevice.h> work
with const attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
11800 368 0 12168 2f88 drivers/net/can/janz-ican3.o
File size After adding 'const':
text data bss dec hex filename
11864 304 0 12168 2f88 drivers/net/can/janz-ican3.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/netdevice.h> work
with const attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
6164 304 0 6468 1944 drivers/net/can/at91_can.o
File size After adding 'const':
text data bss dec hex filename
6228 240 0 6468 1944 drivers/net/can/at91_can.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for extended error reporting.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for extended error reporting.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for extended error reporting.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions (skb_put, __skb_put and pskb_put) return void *
and remove all the casts across the tree, adding a (u8 *) cast only
where the unsigned char pointer was used directly, all done with the
following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_put, __skb_put };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_put, __skb_put };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
which actually doesn't cover pskb_put since there are only three
users overall.
A handful of stragglers were converted manually, notably a macro in
drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many
instances in net/bluetooth/hci_sock.c. In the former file, I also
had to fix one whitespace problem spatch introduced.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CAN FD capable CAN interfaces can handle (classic) CAN 2.0 frames too.
New users usually fail at their first attempt to explore CAN FD on
virtual CAN interfaces due to the current CAN_MTU default.
Set the MTU to CANFD_MTU by default to reduce this confusion.
If someone *really* needs a 'classic CAN'-only device this can be set
with the 'ip' tool with e.g. 'ip link set vcan0 mtu 16' as before.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds the missing kfree() in gs_cmd_reset() to free the
memory that is not used anymore after usb_control_msg().
Cc: linux-stable <stable@vger.kernel.org>
Cc: Maximilian Schneider <max@schneidersoft.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Make sure to use the USB device product-id stored in host-byte order in
a probe error message.
Also remove a redundant reassignment of the local usb_dev variable which
had already been used to retrieve the product id.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes two uninitialized symbol warnings in the new code adding
support of the PEAK-System PCAN-PCI Express FD boards, in the socket-CAN
network protocol family.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In OOM situations where no skb can be allocated, can_change_state() may
be called with cf == NULL. As this function updates the state and error
statistics it's not an option to skip the call to can_change_state() in
OOM situations.
This patch makes can_change_state() robust, so that it can be called
with cf == NULL.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Network devices can allocate reasources and private memory using
netdev_ops->ndo_init(). However, the release of these resources
can occur in one of two different places.
Either netdev_ops->ndo_uninit() or netdev->destructor().
The decision of which operation frees the resources depends upon
whether it is necessary for all netdev refs to be released before it
is safe to perform the freeing.
netdev_ops->ndo_uninit() presumably can occur right after the
NETDEV_UNREGISTER notifier completes and the unicast and multicast
address lists are flushed.
netdev->destructor(), on the other hand, does not run until the
netdev references all go away.
Further complicating the situation is that netdev->destructor()
almost universally does also a free_netdev().
This creates a problem for the logic in register_netdevice().
Because all callers of register_netdevice() manage the freeing
of the netdev, and invoke free_netdev(dev) if register_netdevice()
fails.
If netdev_ops->ndo_init() succeeds, but something else fails inside
of register_netdevice(), it does call ndo_ops->ndo_uninit(). But
it is not able to invoke netdev->destructor().
This is because netdev->destructor() will do a free_netdev() and
then the caller of register_netdevice() will do the same.
However, this means that the resources that would normally be released
by netdev->destructor() will not be.
Over the years drivers have added local hacks to deal with this, by
invoking their destructor parts by hand when register_netdevice()
fails.
Many drivers do not try to deal with this, and instead we have leaks.
Let's close this hole by formalizing the distinction between what
private things need to be freed up by netdev->destructor() and whether
the driver needs unregister_netdevice() to perform the free_netdev().
netdev->priv_destructor() performs all actions to free up the private
resources that used to be freed by netdev->destructor(), except for
free_netdev().
netdev->needs_free_netdev is a boolean that indicates whether
free_netdev() should be done at the end of unregister_netdevice().
Now, register_netdevice() can sanely release all resources after
ndo_ops->ndo_init() succeeds, by invoking both ndo_ops->ndo_uninit()
and netdev->priv_destructor().
And at the end of unregister_netdevice(), we invoke
netdev->priv_destructor() and optionally call free_netdev().
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds Power Management deep Suspend/Resume support for Bosch M_CAN
chip.
When entering deep sleep, the clocks are gated, the interrupts are
disabled. When resuming from deep sleep, the chip needs to be
reinitialized, the clocks ungated and the interrupts enabled.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This creates a function to ungate M_CAN clocks and another to gate the
same clocks, then swaps all gating/ungating code with their respective
function.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This moves clocks gating outside of the m_can_stop function as the
m_can_start function does not (and cannot, at least in current
implementation) ungate clocks. This way, both functions can now be used
symmetrically.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
To avoid possible ECC/parity checksum errors when reading an
uninitialized buffer, the entire Message RAM is initialized when probing
the driver. This initialization is done in the same function reading the
Device Tree properties.
This patch moves the RAM initialization to a separate function so it can
be called separately from device initialization from Device Tree.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-----BEGIN PGP SIGNATURE-----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=lbS7
-----END PGP SIGNATURE-----
Merge tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull hw lockdown support from David Howells:
"Annotation of module parameters that configure hardware resources
including ioports, iomem addresses, irq lines and dma channels.
This allows a future patch to prohibit the use of such module
parameters to prevent that hardware from being abused to gain access
to the running kernel image as part of locking the kernel down under
UEFI secure boot conditions.
Annotations are made by changing:
module_param(n, t, p)
module_param_named(n, v, t, p)
module_param_array(n, t, m, p)
to:
module_param_hw(n, t, hwtype, p)
module_param_hw_named(n, v, t, hwtype, p)
module_param_hw_array(n, t, hwtype, m, p)
where the module parameter refers to a hardware setting
hwtype specifies the type of the resource being configured. This can
be one of:
ioport Module parameter configures an I/O port
iomem Module parameter configures an I/O mem address
ioport_or_iomem Module parameter could be either (runtime set)
irq Module parameter configures an I/O port
dma Module parameter configures a DMA channel
dma_addr Module parameter configures a DMA buffer address
other Module parameter configures some other value
Note that the hwtype is compile checked, but not currently stored (the
lockdown code probably won't require it). It is, however, there for
future use.
A bonus is that the hwtype can also be used for grepping.
The intention is for the kernel to ignore or reject attempts to set
annotated module parameters if lockdown is enabled. This applies to
options passed on the boot command line, passed to insmod/modprobe or
direct twiddling in /sys/module/ parameter files.
The module initialisation then needs to handle the parameter not being
set, by (1) giving an error, (2) probing for a value or (3) using a
reasonable default.
What I can't do is just reject a module out of hand because it may
take a hardware setting in the module parameters. Some important
modules, some ipmi stuff for instance, both probe for hardware and
allow hardware to be manually specified; if the driver is aborts with
any error, you don't get any ipmi hardware.
Further, trying to do this entirely in the module initialisation code
doesn't protect against sysfs twiddling.
[!] Note that in and of itself, this series of patches should have no
effect on the the size of the kernel or code execution - that is
left to a patch in the next series to effect. It does mark
annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
an already existing field"
* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
Annotate hardware config module parameters in sound/pci/
Annotate hardware config module parameters in sound/oss/
Annotate hardware config module parameters in sound/isa/
Annotate hardware config module parameters in sound/drivers/
Annotate hardware config module parameters in fs/pstore/
Annotate hardware config module parameters in drivers/watchdog/
Annotate hardware config module parameters in drivers/video/
Annotate hardware config module parameters in drivers/tty/
Annotate hardware config module parameters in drivers/staging/vme/
Annotate hardware config module parameters in drivers/staging/speakup/
Annotate hardware config module parameters in drivers/staging/media/
Annotate hardware config module parameters in drivers/scsi/
Annotate hardware config module parameters in drivers/pcmcia/
Annotate hardware config module parameters in drivers/pci/hotplug/
Annotate hardware config module parameters in drivers/parport/
Annotate hardware config module parameters in drivers/net/wireless/
Annotate hardware config module parameters in drivers/net/wan/
Annotate hardware config module parameters in drivers/net/irda/
Annotate hardware config module parameters in drivers/net/hamradio/
Annotate hardware config module parameters in drivers/net/ethernet/
...
This typo is quite common. Fix it and add it to the spelling file so
that checkpatch catches it earlier.
Link: http://lkml.kernel.org/r/20170317011131.6881-2-sboyd@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allocate buffers on HEAP instead of STACK for local structures
that are to be sent using usb_control_msg().
Signed-off-by: Maksim Salau <maksim.salau@gmail.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.8
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds a text line in the help section of the CAN_PEAK_USB
config item describing the support of the PCAN-USB X6 adapter, which is
already included in the Kernel since 4.9.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds the support of the PCAN-Chip USB, a stamp module for
customer hardware designs, which communicates via USB 2.0 with the
hardware. The integrated CAN controller supports the protocols CAN 2.0 A/B
as well as CAN FD. The physical CAN connection is determined by external
wiring. The Stamp module with its single-sided mounting and plated
half-holes is suitable for automatic assembly.
Note that the chip is equipped with the same logic than the PCAN-USB FD.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Fixes: dabf54dd1c ("can: ti_hecc: Convert TI HECC driver to DT only driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Autoload the vcan module when a vcan instance is to be created by
'ip link add type vcan'
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Similar to the virtual ethernet driver veth, vxcan implements a
local CAN traffic tunnel between two virtual CAN network devices.
See Kconfig entry for details.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
SocketCAN driver for Microchip CAN BUS Analyzer
(http://www.microchip.com/development-tools/)
Changes in v4:
- possible memory leak fixed in mcba_usb_write_bulk_callback
- LED support added
- failure handling in mcba_usb_probe improved
- C99 initializers for structs on stack
Changes in v3:
- improved/simplified CAN ID conversion
- functions for transmission of skb and cmd separated
- fixed/improved netif_stop_queue handling
- style/cosmetic corrections
Changes in v2:
- Termination handling reimplemented to fit new netlink API
(IFLA_CAN_TERMINATION)
- Bitrate handling reimplemented to fit new netlink API
(IFLA_CAN_BITRATE)
- CAN ID conversion refactored (changed from macro to inline functions)
- CAN DLC handling using get_can_dlc()
- Endianness handling for can_speed introduced
- Debugging removed
- Redundant error prints removed
- Style/cosmetic corrections (i.e. macro names, redefs, inits etc.)
Signed-off-by: Remigiusz Kołłątaj <remigiusz.kollataj@mobica.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
* Added defines for TX Event FIFO Element
* Adapted ndo_start_xmit function.
For versions >= v3.1.x it uses the TX FIFO to optimize the data
throughput. It stores the echo skb at the same index as in the
M_CAN's TX FIFO. The frame's message marker is set to this index.
This message marker is received in the TX Event FIFO after
the message was successfully transmitted. It is used to echo the
correct echo skb back to the network stack.
* Added m_can_echo_tx_event function. It reads all received
message markers in the TX Event FIFO and loops back the
corresponding echo skbs.
* ISR checks for new TX Event Entry interrupt for version >= 3.1.x.
Signed-off-by: Mario Huettel <mario.huettel@gmx.net>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
* TX/TX Event FIFO sizes are configured for version >= v3.1.x
Signed-off-by: Mario Huettel <mario.huettel@gmx.net>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adapts the initialization of the M_CAN. So it can be used
with all versions >= 3.0.x.
Changes:
* Added version element to m_can_priv structure to hold M_CAN version.
* Renamed bittiming structs for version 3.0.x
* Added new bittiming structs for version >= 3.1.x
* Function alloc_m_can_dev takes 2 new arguments. The TX FIFO size and the
base address of the module.
* Chip configuration for CAN_CTRLMODE_LOOPBACK is changed: Enabled
CCCR_MON bit. In combination with TEST_LBCK it activates the internal
loopback mode. Leaving CCCR_MON '0' results in external loopback mode.
* Clocks are temporarily enabled by platform_propbe function in order to
allow read access to the Core Release register and the Control Register.
Registers are used to detect M_CAN version and optional Non-ISO Feature.
Initialization of M_CAN for version >= 3.1.x:
* TX FIFO of M_CAN is used to transmit frames. The driver does not need to
stop the tx queue after each frame sent.
* Initialization of TX Event FIFO is added.
* NON-ISO is fixed for all M_CAN versions < 3.2.x. Version 3.2.x _can_ have
the NISO (Non-ISO) bit which can switch the mode of the M_CAN to Non-ISO
mode. This bit does not have to be writeable. Therefore it is checked.
If it is writable Non-ISO support is added to the controllers supported
CAN modes.
New Functions:
* Function to check the Core Release version. The read value determines the
behaviour of the driver.
* Function to check if the NISO bit for version >= 3.2.x is implemented.
Signed-off-by: Mario Huettel <mario.huettel@gmx.net>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
* Updated register defines to newest M_CAN version (v3.2.1).
* Changed defines in the whole code.
Signed-off-by: Mario Huettel <mario.huettel@gmx.net>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The virtual address of the device was printed. I removed it because it
leaks internal information.
Signed-off-by: Mario Huettel <mario.huettel@gmx.net>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
FIFO water marks disabled because the driver doesn't handle water mark
events.
Signed-off-by: Mario Huettel <mario.huettel@gmx.net>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
* Disabled interrupt line 1. The driver didn't use it.
Signed-off-by: Mario Huettel <mario.huettel@gmx.net>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds the support of the PCAN-PCI Express FD boards made
by PEAK-System, for computers using the PCI Express slot.
The PCAN-PCI Express FD has one or two CAN FD channels, depending
on the model. A galvanic isolation of the CAN ports protects
the electronics of the card and the respective computer against
disturbances of up to 500 Volts. The PCAN-PCI Express FD can be operated
with ambient temperatures in a range of -40 to +85 °C.
Such boards run an extented version of the CAN-FD IP running into USB
CAN-FD interfaces from PEAK-System, so this patch adds several new commands
and their corresponding data types to the PEAK CAN-FD common definitions
header file too.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CAN-FD IP from PEAK-System runs into several kinds of PC CAN-FD
interfaces. Up to now, only the USB CAN-FD adapters were supported by
the Kernel. In order to prepare the adding of some new non-USB CAN-FD
interfaces, this patch moves - and rename - the IP definitions file
from its private (usb) sub-directory into a - newly created - CAN specific
one.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fixes the usage of the const qualifier in the memory pointer arguments
of the declared inline functions. By changing the line containing "const",
this patch also changes the name of the arg into a more usual one.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes the wrong usage of a specific USB data type into a common
header file. This common header file is intended to define the common data
types and values that define access to the PEAK-System CAN-FD IP, whatever
the PC interface is.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When the kernel is running in secure boot mode, we lock down the kernel to
prevent userspace from modifying the running kernel image. Whilst this
includes prohibiting access to things like /dev/mem, it must also prevent
access by means of configuring driver modules in such a way as to cause a
device to access or modify the kernel image.
To this end, annotate module_param* statements that refer to hardware
configuration and indicate for future reference what type of parameter they
specify. The parameter parser in the core sees this information and can
skip such parameters with an error message if the kernel is locked down.
The module initialisation then runs as normal, but just sees whatever the
default values for those parameters is.
Note that we do still need to do the module initialisation because some
drivers have viable defaults set in case parameters aren't specified and
some drivers support automatic configuration (e.g. PNP or PCI) in addition
to manually coded parameters.
This patch annotates drivers in drivers/net/can/.
Suggested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
cc: Wolfgang Grandegger <wg@grandegger.com>
cc: linux-can@vger.kernel.org
cc: netdev@vger.kernel.org
Conflicts were simply overlapping changes. In the net/ipv4/route.c
case the code had simply moved around a little bit and the same fix
was made in both 'net' and 'net-next'.
In the net/sched/sch_generic.c case a fix in 'net' happened at
the same time that a new argument was added to qdisc_hash_add().
Signed-off-by: David S. Miller <davem@davemloft.net>
During probe, the rcar_can driver prints:
rcar_can e6e80000.can: device registered (regs @ e08bc000, IRQ76)
The "regs" value is a virtual address, exposing internal information,
hence stop printing it. The (useful) physical address is already
printed as part of the device name.
Fixes: fd1159318e ("can: add Renesas R-Car CAN driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The incorrect offset was used when trying to read the RXSTCMD register.
Signed-off-by: Markus Marb <markus@marb.org>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds support for the Holt HI-311x CAN controller. The HI311x
CAN controller is capable of transmitting and receiving standard data
frames, extended data frames and remote frames. The HI311x interfaces
with the host over SPI.
Datasheet: www.holtic.com/documents/371-hi-3110_v-rev-jpdf.do
Signed-off-by: Akshay Bhat <nodeax@gmail.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch converts TI HECC driver to DT only driver. This results in
removing ti_hecc.h containing now obsolete platform data.
Former transceiver_switch callback function will be now modelled via
regulator API.
Signed-off-by: Anton Glukhov <anton.a.glukhov@gmail.com>
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Pull networking fixes from David Miller:
1) Fix double-free in batman-adv, from Sven Eckelmann.
2) Fix packet stats for fast-RX path, from Joannes Berg.
3) Netfilter's ip_route_me_harder() doesn't handle request sockets
properly, fix from Florian Westphal.
4) Fix sendmsg deadlock in rxrpc, from David Howells.
5) Add missing RCU locking to transport hashtable scan, from Xin Long.
6) Fix potential packet loss in mlxsw driver, from Ido Schimmel.
7) Fix race in NAPI handling between poll handlers and busy polling,
from Eric Dumazet.
8) TX path in vxlan and geneve need proper RCU locking, from Jakub
Kicinski.
9) SYN processing in DCCP and TCP need to disable BH, from Eric
Dumazet.
10) Properly handle net_enable_timestamp() being invoked from IRQ
context, also from Eric Dumazet.
11) Fix crash on device-tree systems in xgene driver, from Alban Bedel.
12) Do not call sk_free() on a locked socket, from Arnaldo Carvalho de
Melo.
13) Fix use-after-free in netvsc driver, from Dexuan Cui.
14) Fix max MTU setting in bonding driver, from WANG Cong.
15) xen-netback hash table can be allocated from softirq context, so use
GFP_ATOMIC. From Anoob Soman.
16) Fix MAC address change bug in bgmac driver, from Hari Vyas.
17) strparser needs to destroy strp_wq on module exit, from WANG Cong.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (69 commits)
strparser: destroy workqueue on module exit
sfc: fix IPID endianness in TSOv2
sfc: avoid max() in array size
rds: remove unnecessary returned value check
rxrpc: Fix potential NULL-pointer exception
nfp: correct DMA direction in XDP DMA sync
nfp: don't tell FW about the reserved buffer space
net: ethernet: bgmac: mac address change bug
net: ethernet: bgmac: init sequence bug
xen-netback: don't vfree() queues under spinlock
xen-netback: keep a local pointer for vif in backend_disconnect()
netfilter: nf_tables: don't call nfnetlink_set_err() if nfnetlink_send() fails
netfilter: nft_set_rbtree: incorrect assumption on lower interval lookups
netfilter: nf_conntrack_sip: fix wrong memory initialisation
can: flexcan: fix typo in comment
can: usb_8dev: Fix memory leak of priv->cmd_msg_buffer
can: gs_usb: fix coding style
can: gs_usb: Don't use stack memory for USB transfers
ixgbe: Limit use of 2K buffers on architectures with 256B or larger cache lines
ixgbe: update the rss key on h/w, when ethtool ask for it
...
The priv->cmd_msg_buffer is allocated in the probe function, but never
kfree()ed. This patch converts the kzalloc() to resource-managed
kzalloc.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes five minor style issues, spaces are between bitwise OR
operators.
Signed-off-by: Ethan Zonca <e@ethanzonca.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fixes: 05ca527000 can: gs_usb: add ethtool set_phys_id callback to locate physical device
The gs_usb driver is performing USB transfers using buffers allocated on
the stack. This causes the driver to not function with vmapped stacks.
Instead, allocate memory for the transfer buffers.
Signed-off-by: Ethan Zonca <e@ethanzonca.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.8
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch switches the imx6 and vf610 based SoCs from the hardware FIFO
to the timestamp based rx offloading.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The flexcan IP core has 64 mailboxes. For now they are configured for
RX as a hardware FIFO. This FIFO has a fixed depth of 6 CAN frames. In
some high load scenarios it turns out thas this buffer is too small.
In order to have a buffer larger than the 6 frames FIFO, this patch adds
support for timestamp based offloading via the generic rx-offload
infrastructure.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In order to receive RTR frames in the non HW FIFO mode the RSS and EACEN bits
of the reg_ctrl2 have to be activated. As this has no side effect in the FIFO
mode, we do this unconditionally on cores with the reg_ctrl2.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Modern flexcan IP cores support two RX modes. One is using the 6 fames deep
hardware FIFO, the other is using up to 64 mailboxes (in non FIFO mode). For
now only the HW FIFO mode is activated.
In order to make use of the RX mailboxes the individual RX masking feature has
to be activated, otherwise matching mailboxes are overwritten during the
reception process. This however switches on the individual RX masking, which
uses reg_rximr registers for masking.
This patch activates the individual RX masking feature unconditionally and
initializes the mask registers (reg_rximr) with 0x0 == "don't care", which
switches off any filtering.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch converts the flexcan driver to make use of the rx-offload
can_rx_offload_irq_offload_fifo() helper function. The idea is to read
the CAN frames already in the interrupt context, as the depth of the
flexcan HW FIFO is too shallow, resulting in too many missed frames.
During a normal NAPI poll the frames are the pushed into the upper
layers.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch makes the TX mailbox selectable duing runtime. This is a preparation
patch to use of the hardware FIFO selectable via runtime. As the TX mailbox
number is different in HW FIFO and normal mode.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch converts the define FLEXCAN_IFLAG_DEFAULT into the runtime
calculated value priv->reg_imask1_default. This is a preparation patch to make
the TX mailbox selectable during runtime, too.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch changes the flexcan_irq() function to only return
IRQ_HANDLED, if the interrupt really has been handled, otherwise
IRQ_NONE is returned.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch removed the not needed initialisation from the new_state,
rx_state, tx_state variabled.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch converts the rx_errors and tx_errors from int into bool
values, to reflect their actual meaning.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some CAN controllers don't implement a FIFO in hardware, but fill their
mailboxes in a particular order (from lowest to highest or highest to lowest).
This makes problems to read the frames in the correct order from the hardware,
as new frames might be filled into just read (low) mailboxes. This gets worse,
when following new frames are received into not read (higher) mailboxes.
On the bright side some these CAN controllers put a timestamp on each received
CAN frame. This patch adds support to offload CAN frames in interrupt context,
order them by timestamp and then transmitted in a NAPI context.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some CAN controllers have a usable FIFO already but can still benefit
from off-loading the CAN controller FIFO. The CAN frames of the FIFO are
read and put into a skb queue during interrupt and then transmitted in a
NAPI context.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error return ret is never zero in the error handling path in
softingcs_probe, so the check for non-zero and returning -ENODEV
is logically dead code and hence redundant. Remove it and just
return ret.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some CAN interfaces only support fixed fixed bitrates. This patch adds a
netlink interface to get the list of the CAN interface's fixed bitrates and
data bitrates.
Inside the driver arrays of supported data- bitrate values are defined.
const u32 drvname_bitrate[] = { 20000, 50000, 100000 };
const u32 drvname_data_bitrate[] = { 200000, 500000, 1000000 };
struct drvname_priv *priv;
priv = netdev_priv(dev);
priv->bitrate_const = drvname_bitrate;
priv->bitrate_const_cnt = ARRAY_SIZE(drvname_bitrate);
priv->data_bitrate_const = drvname_data_bitrate;
priv->data_bitrate_const_cnt = ARRAY_SIZE(drvname_data_bitrate);
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Until commit
08da7da41e can: provide a separate bittiming_const parameter to
bittiming functions
it was possible to have devices not providing bittiming_const. This can
be used for hardware that only support pre-defined fixed bitrates.
Although no mainline driver is using this feature so far.
This patch re-introduces this feature for the bitrate and the data
bitrate (of CANFD controllers). The driver can specify the
{data_,}bittiming_const (if the bittiming parameters should be
calculated from the bittiming_const) as before or no
{data_,}bittiming_const but implement the do_set_{data,}bittiming
callback.
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds a netlink interface to configure the CAN bus termination of
CAN interfaces.
Inside the driver an array of supported termination values is defined:
const u16 drvname_termination[] = { 60, 120, CAN_TERMINATION_DISABLED };
struct drvname_priv *priv;
priv = netdev_priv(dev);
priv->termination_const = drvname_termination;
priv->termination_const_cnt = ARRAY_SIZE(drvname_termination);
priv->termination = CAN_TERMINATION_DISABLED;
And the funtion to set the value has to be defined:
priv->do_set_termination = drvname_set_termination;
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Reviewed-by: Ramesh Shanmugasundaram <Ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In order to make the driver work with the common clock framework, this
patch converts the clk_enable()/clk_disable() to
clk_prepare_enable()/clk_disable_unprepare().
Also add error checking for clk_prepare_enable().
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The priv->device pointer for c_can_pci is never set, but it is used
without a NULL check in c_can_start(). Setting it in c_can_pci_probe()
like c_can_plat_probe() prevents c_can_pci.ko from crashing, with and
without CONFIG_PM.
This might also cause the pm_runtime_*() functions in c_can.c to
actually be executed for c_can_pci devices - they are the only other
place where priv->device is used, but they all contain a null check.
Signed-off-by: Einar Jón <tolvupostur@gmail.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
That's the default now, no need for makefiles to set it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
It's another busy cycle for the docs tree, as the sphinx conversion
continues. Highlights include:
- Further work on PDF output, which remains a bit of a pain but should be
more solid now.
- Five more DocBook template files converted to Sphinx. Only 27 to go...
Lots of plain-text files have also been converted and integrated.
- Images in binary formats have been replaced with more source-friendly
versions.
- Various bits of organizational work, including the renaming of various
files discussed at the kernel summit.
- New documentation for the device_link mechanism.
...and, of course, lots of typo fixes and small updates.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJYTbl7AAoJEI3ONVYwIuV63NIP/REwzThnGWFJMRSuq8Ieq2r9
sFSQsaGTGlhyKiDoEooo+SO/Za3uTonjK+e7WZg8mhdiEdamta5aociU/71C1Yy/
T9ur0FhcGblrvZ1NidSDvCLwuECZOMMei7mgLZ9a+KCpc4ANqqTVZSUm1blKcqhF
XelhVXxBa0ar35l/pVzyCxkdNXRWXv+MJZE8hp5XAdTdr11DS7UY9zrZdH31axtf
BZlbYJrvB8WPydU6myTjRpirA17Hu7uU64MsL3bNIEiRQ+nVghEzQC8uxeUCvfVx
r0H5AgGGQeir+e8GEv2T20SPZ+dumXs+y/HehKNb3jS3gV0mo+pKPeUhwLIxr+Zh
QY64gf+jYf5ISHwAJRnU0Ima72ehObzSbx9Dko10nhq2OvbR5f83gjz9t9jKYFU7
RDowICA8lwqyRbHRoVfyoW8CpVhWFpMFu3yNeJMckeTish3m7ANqzaWslbsqIP5G
zxgFMIrVVSbeae+sUeygtEJAnWI09aZ4tuaUXYtGWwu6ikC/3aV6DryP4bthG2LF
A19uV4nMrLuuh8g2wiTHHjMfjYRwvSn+f9yaolwJhwyNDXQzRPy+ZJ3W/6olOkXC
bAxTmVRCW5GA/fmSrfXmW1KbnxlWfP2C62hzZQ09UHxzTHdR97oFLDQdZhKo1uwf
pmSJR0hVeRUmA4uw6+Su
=A0EV
-----END PGP SIGNATURE-----
Merge tag 'docs-4.10' of git://git.lwn.net/linux
Pull documentation update from Jonathan Corbet:
"These are the documentation changes for 4.10.
It's another busy cycle for the docs tree, as the sphinx conversion
continues. Highlights include:
- Further work on PDF output, which remains a bit of a pain but
should be more solid now.
- Five more DocBook template files converted to Sphinx. Only 27 to
go... Lots of plain-text files have also been converted and
integrated.
- Images in binary formats have been replaced with more
source-friendly versions.
- Various bits of organizational work, including the renaming of
various files discussed at the kernel summit.
- New documentation for the device_link mechanism.
... and, of course, lots of typo fixes and small updates"
* tag 'docs-4.10' of git://git.lwn.net/linux: (193 commits)
dma-buf: Extract dma-buf.rst
Update Documentation/00-INDEX
docs: 00-INDEX: document directories/files with no docs
docs: 00-INDEX: remove non-existing entries
docs: 00-INDEX: add missing entries for documentation files/dirs
docs: 00-INDEX: consolidate process/ and admin-guide/ description
scripts: add a script to check if Documentation/00-INDEX is sane
Docs: change sh -> awk in REPORTING-BUGS
Documentation/core-api/device_link: Add initial documentation
core-api: remove an unexpected unident
ppc/idle: Add documentation for powersave=off
Doc: Correct typo, "Introdution" => "Introduction"
Documentation/atomic_ops.txt: convert to ReST markup
Documentation/local_ops.txt: convert to ReST markup
Documentation/assoc_array.txt: convert to ReST markup
docs-rst: parse-headers.pl: cleanup the documentation
docs-rst: fix media cleandocs target
docs-rst: media/Makefile: reorganize the rules
docs-rst: media: build SVG from graphviz files
docs-rst: replace bayer.png by a SVG image
...
Fix for bad memory access while disconnecting. netdev is freed before
private data free, and dev is accessed after freeing netdev.
This makes a slub problem, and it raise kernel oops with slub debugger
config.
Signed-off-by: Jiho Chu <jiho.chu@samsung.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEES2FAuYbJvAGobdVQPTuqJaypJWoFAlhAJY0THG1rbEBwZW5n
dXRyb25peC5kZQAKCRA9O6olrKklam88B/0dgD2R9D8udVyHnp1CGVrWm+REER49
g6V2ZqIqfxaAFEiQFIhySJJtWYt4vHAC2A3Mwx6yyv9qugYb26LCiSt3XQPlPNY4
yVFpVzOMsFjmSu9PQ7u47b7/IKmqmSuuuQQWm3rDxDQC+KLKmH1TfULXzqDQ/yR/
+gNTvi6Zwfi6rFU7B33I6cT0VhfnWXhbAbBdg4jNmW5WAyz+WT6c9J9oXQMRw5VW
ESTYrU2c+IVK3Z3e0BOmnCytaPrxE6j1OmT0LNsVR5aoXDmK3jDNln/7cPEOCkD3
3t9ub+gqfeaMIjyDI3yBcy75Gjk3mFQMXs/3LVTivwZySgGldOak/iyL
=vXN1
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.10-20161201' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2016-12-01
this is a pull request of 4 patches for net-next/master.
There are two patches by Chris Paterson for the rcar_can and rcar_canfd
device tree binding documentation. And a patch by Geert Uytterhoeven
that corrects the order of interrupt specifiers.
The fourth patch by Colin Ian King fixes a spelling error in the
kvaser_usb driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake "oustanding" to "outstanding" in
comment and dev_dbg message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This adds support for PEAK-System PCAN-USB X6 USB to CAN interface.
The CAN FD adapter PCAN-USB X6 allows the connection of up to 6 CAN FD
or CAN networks to a computer via USB. The interface is installed in an
aluminum profile casing and is shipped in versions with D-Sub connectors
or M12 circular connectors.
The PCAN-USB X6 registers in the USB sub-system as if 3x PCAN-USB-Pro FD
adapters were plugged. So, this patch:
- updates the PEAK_USB entry of the corresponding Kconfig file
- defines and adds the device id. of the PCAN-USB X6 (0x0014) into the
table of supported device ids
- defines and adds the new software structure implementing the PCAN-USB X6,
which is obviously a clone of the software structure implementing the
PCAN-USB Pro FD.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This fixes the bitimings fields ranges supported by all the CAN-FD USB
interfaces of the PEAK-System CAN-FD adapters.
Very first development versions of the IP core API defined smaller TSGEx
and SJW fields for both nominal and data bittimings records than the
production versions. This patch fixes them by enlarging their sizes to
the actual values:
field: old size: fixed size:
nominal TSGEG1 6 8
nominal TSGEG2 4 7
nominal SJW 4 7
data TSGEG1 4 5
data TSGEG2 3 4
data SJW 2 4
Note that this has no other consequences than offering larger choice to
bitrate encoding.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds support for Moxa CAN devices.
Signed-off-by: Lukas Resch <l.resch@incubedit.com>
Signed-off-by: Christoph Zehentner <c.zehentner@incubedit.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The previous patch renamed several files that are cross-referenced
along the Kernel documentation. Adjust the links to point to
the right places.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A timer was used to restart after the bus-off state, leading to a
relatively large can_restart() executed in an interrupt context,
which in turn sets up pinctrl. When this happens during system boot,
there is a high probability of grabbing the pinctrl_list_mutex,
which is locked already by the probe() of other device, making the
kernel suspect a deadlock condition [1].
To resolve this issue, the restart_timer is replaced by a delayed
work.
[1] https://github.com/victronenergy/venus/issues/24
Signed-off-by: Sergei Miroshnichenko <sergeimir@emcraft.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Configure the transmitter delay register at +0x1c to correctly handle
the CAN FD bitrate switch (BRS). This moves the SSP (secondary sample
point) to a proper offset, so that the TDC mechanism works and won't
generate error frames on the CAN link.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
On a imx6ul-pico board the following error is seen during system suspend:
dpm_run_callback(): platform_pm_resume+0x0/0x54 returns -110
PM: Device 2090000.flexcan failed to resume: error -110
The reason for this suspend error is because when the CAN interface is not
active the clocks are disabled and then flexcan_chip_enable() will
always fail due to a timeout error.
In order to fix this issue, only call flexcan_chip_enable/disable()
when the CAN interface is active.
Based on a patch from Dong Aisheng in the NXP kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
Silent ignorance of errors during probe procedure is a bad thing, this
patch fixes it. Extra message added for hardware initialization
failure. Such common issues are mostly caused by wrong wiring. Message
about success added as well, it should be useful to debug new hardware
configuration, especially in case of several CAN buses.
Signed-off-by: Ed Spiridonov <edo.rus@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As per Wolfgang G, all new drivers should support decreasing state
transition(back-to-error-active). This patch adds this support.
This driver configures the controller to halt on bus-off entry. Hence,
when in error states less than bus off state, the TEC/REC counters
are checked for lower state transition eligibility and action.
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The controller can operate in one of the two global modes
- CAN FD only mode (default)
- Classical CAN (CAN2.0) only mode
This patch adds support for Classical CAN only mode. It can be enabled
by defining the optional device tree property "renesas,no-can-fd" of this
node.
Note: R-Car Gen3 h/w manual v0.51E shows bit6 of RSCFDnCFDGCFG as
reserved, which is incorrect. This bit is same as RSCFDnGCFG.
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds support for Kvaser Leaf Light HS v2 OEM, Mini PCI
Express 2xHS and USBcan Light 2xHS.
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
For 'real' hardware CAN devices the netlink interface is used to set CAN
specific communication parameters. Real CAN hardware can not be created nor
removed with the ip tool ...
This patch adds a private dellink function for the CAN device driver interface
that does just nothing.
It's a follow up to commit 993e6f2fd ("can: fix oops caused by wrong rtnl
newlink usage") but for dellink.
Reported-by: ajneu <ajneu1@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
With upstream commit bb208f144c (can: fix handling of unmodifiable
configuration options) a new can_validate() function was introduced.
When invoking 'ip link set can0 type can' without any configuration data
can_validate() tries to validate the content without taking into account that
there's totally no content. This patch adds a check for missing content.
Reported-by: ajneu <ajneu1@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patchs adds basic support for the bytewerk.org candleLight interface,
a open hardware (CERN OHL) USB CAN adapter.
Signed-off-by: Hubert Denkmair <hubert@denkmair.de>
Signed-off-by: Maximilian Schneider <max@schneidersoft.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
At high bus load it could happen that "at91_poll()" enters with all RX
message boxes filled up. If then at the end the "quota" is exceeded as
well, "rx_next" will not be reset to the first RX mailbox and hence the
interrupts remain disabled.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Tested-by: Amr Bekhit <amrbekhit@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When testing CAN write floods on Altera's CycloneV, the first 2 bytes
are sometimes 0x00, 0x00 or corrupted instead of the values sent. Also
observed bytes 4 & 5 were corrupted in some cases.
The D_CAN Data registers are 32 bits and changing from 16 bit writes to
32 bit writes fixes the problem.
Testing performed on Altera CycloneV (D_CAN). Requesting tests on other
C_CAN & D_CAN platforms.
Reported-by: Richard Andrysek <richard.andrysek@gomtec.de>
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch clubs the Renesas controller drivers in one rcar dir.
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds support for the CAN FD controller found in Renesas R-Car
SoCs. The controller operates in CAN FD only mode by default.
CAN FD mode supports both Classical CAN & CAN FD frame formats. The
controller supports ISO 11898-1:2015 CAN FD format only.
This controller supports two channels and the driver can enable either
or both of the channels.
Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one
per channel) for transmission. Rx filter rules are configured to the
minimum (one per channel) and it accepts Standard, Extended, Data &
Remote Frame combinations.
Note: There are few documentation errors in R-Car Gen3 Hardware User
Manual v0.5E with respect to CAN FD controller. They are listed below:
1. CAN FD interrupt numbers 29 & 30 are listed as per channel
interrupts. However, they are common to both channels (i.e.) they are
global and channel interrupts respectively.
2. CANFD clock is derived from PLL1. This is not documented.
3. CANFD clock is further divided by (1/2) within the CAN FD controller.
This is not documented.
4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It
is specified 4 Tq in the manual.
5. The maximum number of message RAM area the controller can use is 3584
bytes. It is specified 10752 bytes in the manual.
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch Implements the ethtool set_phys_id callback to ease the
locating of specific physical devices. Currently only supported on
candleLight interfaces.
Signed-off-by: Hubert Denkmair <hubert@denkmair.de>
Signed-off-by: Maximilian Schneider <max@schneidersoft.net>
[mkl: split codingstyle change sinto separate patch]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch converts "1 << n" by BIT(n) and fixes the indention. No
functional change.
Signed-off-by: Hubert Denkmair <hubert@denkmair.de>
Signed-off-by: Maximilian Schneider <max@schneidersoft.net>
[mkl: split codingstyle changes into separate patch]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This driver does not do anything special in module init/exit. This patch
eliminates the module init/exit boilerplate code by utilizing the
module_isa_driver macro.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use CAN_MTU macro instead of sizeof(struct can_frame) just like the
other drivers do.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch optimizes the calculation of the sample point. To understand what it
does have a look at the original implementation.
If there is a combination of timing parameters where both the bitrate and
sample point error are 0 the current implementation will find it.
However if the reference clock doesn't allow an optimal bitrate (this means the
bitrate error is always != 0) there might be several timing parameter
combinations having the same bitrate error. The original implementation will
allways choose the one with the highest brp. The actual sample point error
isn't taken into account.
This patch changes the algorithm to minimize the sample point error, too. Now a
brp/tseg combination is accepted as better if one of these condition are
fulfilled:
1) the bit rate error must be smaller, or
2) the bit rate error must be equal and
the sample point error must be equal or smaller
If a smaller bit rate error is found the sample point error is reset. This
ensures that we first optimize for small bit rate error and then for small
sample point errors.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The updated specification for the IFI CANFD core contains description
of more detailed error reporting capability of the core. Implement
support for this detailed error reporting.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Only increment the TX counters in the irq handler if a CAN message
was sent. The current code incremented the counters also if the TX
FIFO empty interrupt happened, which is incorrect.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CAN_CTRLMODE_FD flag is set for both ISO and BOSCH CANFD mode,
while the CAN_CTRLMODE_FD_NON_ISO is additional flag which is only
set for CANFD-BOSCH mode. Fix the handling of the flags to reflect
this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no distinction between bittiming constants for the slow and
fast part of the CANFD operation on this controller, so just use one
single bittiming constant set.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The updated documentation regarding the IFI CANFD core from April 2016
adds more details regarding the timing calculation. There is no longer
any distinction in the timing calculation between CANFD and CAN2.0, but
instead there are two timing modes -- 4_12_6_6 and 7_9_8_8 -- where the
numbers mean the width in bits of the SJW/Prescaler/TimeA/TimeB fields.
The code uses 7_9_8_8 mode, which allows more fine-grained control over
the timing.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Start the NAPI polling in case the bus warning interrupt happens,
since it is the poll function which checks and reports the warning.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Modified the USB device table to use only the first USB interface, as is
the case with GS USB devices. This allows other GS USB compatible
devices to be more flexible with their remaining interfaces.
Signed-off-by: Maximilian Schneider <max@schneidersoft.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
My patch of May 2015 was missing the changed handling of error
indications. With CAL/CANopen firmware the NMTS-SlaveEventIndication
must be used instead of CAN-EventIndication. An appropriate slave node
must be configured to report the errors.
In our department (about 15 development systems with Janz ICAN3-
modules with firmware 1.48, my system also with firmware ICANOS 1.35)
we use the driver with this patch for about one year: no known problems.
Signed-off-by: Andreas Gröger <andreas24groeger@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As described in 'can: m_can: tag current CAN FD controllers as non-ISO'
(6cfda7fbeb) it is possible to define fixed configuration options by
setting the according bit in 'ctrlmode' and clear it in 'ctrlmode_supported'.
This leads to the incovenience that the fixed configuration bits can not be
passed by netlink even when they have the correct values (e.g. non-ISO, FD).
This patch fixes that issue and not only allows fixed set bit values to be set
again but now requires(!) to provide these fixed values at configuration time.
A valid CAN FD configuration consists of a nominal/arbitration bittiming, a
data bittiming and a control mode with CAN_CTRLMODE_FD set - which is now
enforced by a new can_validate() function. This fix additionally removed the
inconsistency that was prohibiting the support of 'CANFD-only' controller
drivers, like the RCar CAN FD.
For this reason a new helper can_set_static_ctrlmode() has been introduced to
provide a proper interface to handle static enabled CAN controller options.
Reported-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Reviewed-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Cc: <stable@vger.kernel.org> # >= 3.18
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Replace scheduled to be removed create_freezable_workqueue with
alloc_workqueue.
priv->wq should be explicitly set as freezable to ensure it is frozen
in the suspend sequence and work items are drained so that no new work
item starts execution until thawed. Thus, use of WQ_FREEZABLE flag
here is required.
WQ_MEM_RECLAIM flag has been set here to ensure forward progress
regardless of memory pressure.
The order of execution is not important so set @max_active as 0.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds support for the Marathon CAN-bus-PCIe card to the
sja1000 driver. For more information see:
http://can.marathon.ru/page/devices/can-bus-pcie
Signed-off-by: Nikita Edward Baruzdin <nebaruzdin@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
According to SJA1000 documentation the location of error is available
regardless of an error type. Therefore it should always be forwarded to
SocketCAN.
Signed-off-by: Nikita Edward Baruzdin <nebaruzdin@lvk.cs.msu.su>
Signed-off-by: Alexander GQ Gerasiov <gq@cs.msu.su>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In case of CAN2.0 EFF frame, the controller handles frame IDs in a
rather bizzare way. The ID is split into an extended part, IDX[28:11]
and standard part, ID[10:0]. In the TX path, the core first sends the
top 11 bits of the IDX, followed by ID and finally the rest of IDX.
In the RX path, the core stores the ID the LSbit part of IDX field,
followed by the LSbit parts of real IDX. The MSbit parts of IDX are
stored in ID field of the register.
This patch implements the necessary bit shuffling to mitigate this
obscure behavior. In case two of these controllers are connected
together, the RX and TX bit swapping nullifies itself and the issue
does not manifest. The issue only manifests when talking to another
different CAN controller.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The RX and TX ID mask for CAN2.0 is 11 bits wide. This patch fixes
the incorrect mask, which caused the CAN IDs to miss the MSBit both
on receive and transmit.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The TX DLC, the transmission length information, was not written
into the transmit configuration register. When using the CAN core
with different CAN controller, the receiving CAN controller will
receive only the ID part of the CAN frame, but no data at all.
This patch adds the TX DLC into the register to fix this issue.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The clock generation does not match reality when using the CAN IP
core outside of the FPGA design. This patch fixes the computation
of values which are programmed into the clock generator registers.
First, there are some off-by-one errors which manifest themselves
only when communicating with different controller, so those are
fixed.
Second, the bits in the clock generator registers have different
meaning depending on whether the core is in ISO CANFD mode or any
of the other modes (BOSCH CANFD or CAN2.0). Detect the ISO CANFD
mode and fix handling of this special case of clock configuration.
Finally, the CAN clock speed is in CANCLOCK register, not SYSCLOCK
register, so fix this as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Only two bits (RX0OVR and RX1OVR) are writable in EFLG, write is useless
if these bits aren't set.
Signed-off-by: Ed Spiridonov <edo.rus@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add fallback compatibility string for R-Car Gen 1 and Gen2.
In the case of Renesas R-Car hardware we know that there are generations of
SoCs, e.g. Gen 1 and Gen 2. But beyond that its not clear what the
relationship between IP blocks might be. For example, I believe that
r8a7779 is older than r8a7778 but that doesn't imply that the latter is a
descendant of the former or vice versa.
We can, however, by examining the documentation and behaviour of the
hardware at run-time observe that the current driver implementation appears
to be compatible with the IP blocks on SoCs within a given generation.
For the above reasons and convenience when enabling new SoCs a
per-generation fallback compatibility string scheme being adopted for
drivers for Renesas SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes the coding style issues introduced in commit:
90cfde4658 can: ems_usb: Fix possible tx overflow
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
gs_destroy_candev() erroneously calls kfree() on a struct gs_can *, which is
allocated through alloc_candev() and should instead be freed using
free_candev() alone.
The inappropriate use of kfree() causes the kernel to hang when
gs_destroy_candev() is called.
Only the struct gs_usb * which is allocated through kzalloc() should be freed
using kfree() when the device is disconnected.
Signed-off-by: Maximilian Schneider <max@schneidersoft.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Conflicts:
drivers/net/phy/bcm7xxx.c
drivers/net/phy/marvell.c
drivers/net/vxlan.c
All three conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the problem that more CAN messages could be sent to the
interface as could be send on the CAN bus. This was more likely for slow baud
rates. The sleeping _start_xmit was woken up in the _write_bulk_callback. Under
heavy TX load this produced another bulk transfer without checking the
free_slots variable and hence caused the overflow in the interface.
Signed-off-by: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The patch adds support for IFI CAN/FD controller [1]. This driver
currently supports sending and receiving both standard CAN and new
CAN/FD frames. Both ISO and BOSCH variant of CAN/FD is supported.
[1] http://www.ifi-pld.de/IP/CANFD/canfd.html
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Just sort the drivers in the Makefile, no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Sort the Kconfig includes, no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Technologic Systems provides an IP compatible with the SJA1000,
instantiated in an FPGA. Because of some bus widths issue, access to
registers is made through a "window" that works like this:
base + 0x0: address to read/write
base + 0x2: 8-bit register value
This commit adds a new compatible device, "technologic,sja1000", with
read and write functions using the window mechanism.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This commit adds the capability to allocate and init private data
embedded in the sja1000_priv structure on a per-compatible basis. The
device node is passed as a parameter of the init callback to allow
parsing of custom device tree properties.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Conflicts:
drivers/net/ethernet/renesas/ravb_main.c
kernel/bpf/syscall.c
net/ipv4/ipmr.c
All three conflicts were cases of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of enabling/disabling clocks at several locations in the driver,
Use the runtime_pm framework. This consolidates the actions for runtime PM
In the appropriate callbacks and makes the driver more readable and mantainable.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The assignment 'cf->data[2] |= CAN_ERR_PROT_UNSPEC' used at CAN error message
creation time is obsolete as CAN_ERR_PROT_UNSPEC is zero and cf->data[2] is
initialized with zero in alloc_can_err_skb() anyway.
So we could either assign 'cf->data[2] = CAN_ERR_PROT_UNSPEC' correctly or we
can remove the obsolete OR operation entirely.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As Dan Carpenter reported in http://marc.info/?l=linux-can&m=144793696016187
the assignment of the error location in CAN error messages had some bit wise
overlaps. Indeed the value to be assigned in data[3] is no bitfield but defines
a single value which points to a location inside the CAN frame on the wire.
This patch fixes the assignments for the error locations in error messages.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
According to SJA1000 data sheet error-warning (EI) interrupt is not
cleared by setting the controller in to reset-mode.
Then if we have the following case:
- system is suspended (echo mem > /sys/power/state) and SJA1000 is left
in operating state
- A bus error condition occurs which activates EI interrupt, system is
still suspended which means EI interrupt will be not be handled nor
cleared.
If the above two events occur, on resume there is no way to return the
SJA1000 to operating state, except to cycle power to it.
By simply reading the IR register on start we will clear any previous
conditions that could be present.
Signed-off-by: Mirza Krak <mirza.krak@hostmobility.com>
Reported-by: Christian Magnusson <Christian.Magnusson@semcon.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
=DgXG
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
Minor overlapping changes in net/ipv4/ipmr.c, in 'net' we were
fixing the "BH-ness" of the counter bumps whilst in 'net-next'
the functions were modified to take an explicit 'net' parameter.
Signed-off-by: David S. Miller <davem@davemloft.net>
The sizeof() is invoked on an incorrect variable, likely due to some
copy-paste error, and this might result in memory corruption. Fix this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: netdev@vger.kernel.org
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
struct at91_can_data was used to pass a callback to the driver, allowing it
to switch the transceiver on and off. As all at91 boards are now using DT,
this is not used anymore, remove that structure.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch change description of the module.
Signed-off-by: Gerhard Bertelsmann <info@gerhard-bertelsmann.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes a bug in arbitration error reporting
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Gerhard Bertelsmann <info@gerhard-bertelsmann.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
While new PEAK_PCIE_OEM_ID has been defined since 3.17, no corresponding
entry has been added in the peak_pci_tbl[] of the peak_pci CAN driver.
This patch enables now users of the PCAN-PCI Express OEM card to run the
peak_pci driver too.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch defers the writing of the interrupts bits of the CTRL register order
to enables all interrupts atomically at the the of the flexcan_chip_start()
function.
Suggested-by: Torsten Lang <torsten.lang@uweschneider.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch gives the member of flexcan_priv holding mailboxes a sensible name,
by renaming from "cantxfg" to "mb":
struct flexcan_priv::cantxfg -> struct flexcan_priv::mb
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch renames the pointer to the mmio address space from "base" to "regs"
and changes the type from "void __iomem *" to "struct flexcan_regs __iomem *".
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch renames the "features" member of struct flexcan_devtype_data to
"quirks". The corresponding defines are renamed too, to reflect what they
actually do.
FLEXCAN_HAS_V10_FEATURES -> FLEXCAN_QUIRK_DISABLE_RXFG
FLEXCAN_HAS_BROKEN_ERR_STATE -> FLEXCAN_QUIRK_BROKEN_ERR_STATE
FLEXCAN_HAS_MECR_FEATURES -> FLEXCAN_QUIRK_DISABLE_MECR
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch changes the order the individual bits of the mcr register in
flexcan_chip_start() are or'ed together to match the datasheet. The inline
documentation is adjusted accordingly.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Kernel module for Allwinner A10/A20 CAN controller.
Signed-off-by: Gerhard Bertelsmann <info@gerhard-bertelsmann.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CAN FD data bittiming constants are provided via netlink only when there
are valid CAN FD constants available in priv->data_bittiming_const.
Due to the indirection of pointer assignments in the peak_usb driver the
priv->data_bittiming_const never becomes NULL - not even for non-FD adapters.
The data_bittiming_const points to zero'ed data which leads to this result
when running 'ip -details link show can0':
35: can0: <NOARP,ECHO> mtu 16 qdisc noop state DOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state STOPPED restart-ms 0
pcan_usb: tseg1 1..16 tseg2 1..8 sjw 1..4 brp 1..64 brp-inc 1
: dtseg1 0..0 dtseg2 0..0 dsjw 1..0 dbrp 0..0 dbrp-inc 0 <== BROKEN!
clock 8000000
This patch changes the struct peak_usb_adapter::bittiming_const and struct
peak_usb_adapter::data_bittiming_const to pointers to fix the assignemnt
problems.
Cc: linux-stable <stable@vger.kernel.org> # >= 4.0
Reported-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This message isn't really helpful for the general reader of the kernel
logs, so should not be printed with info level. All other register
programming outputs in the flexcan driver already use the debug level.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This fixes typos in gs_usb.c where 'receive' is misspelled
as 'recieve'.
Signed-off-by: Nik Nyby <nikolas@gnu.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The regulators power and transceiver are optional. If those are not
present, the pointer (or error pointer) is correctly handled by the
driver, hence we can use devm_regulator_get_optional safely, which
avoids regulators getting created.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If a valid power regulator or a dummy regulator is used (which
happens to be the case when no regulator is specified), restart_work
is queued no matter whether the device was running or not at suspend
time. Since work queues get initialized in the ndo_open callback,
resuming leads to a NULL pointer exception.
Reverse exactly the steps executed at suspend time:
- Enable the power regulator in any case
- Enable the transceiver regulator if the device was running, even in
case we have a power regulator
- Queue restart_work only in case the device was running
Fixes: bf66f3736a ("can: mcp251x: Move to threaded interrupts instead of workqueues.")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Cc: Bernd Krumboeck <b.krumboeck@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Cc: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Cc: Thomas Körper <thomas.koerper@esd.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Cc: Anant Gole <anantgole@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Cc: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Cc: Aaron Wu <Aaron.wu@analog.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Commit 514ac99c64 "can: fix multiple delivery of a single CAN frame for
overlapping CAN filters" requires the skb->tstamp to be set to check for
identical CAN skbs.
Without timestamping to be required by user space applications this timestamp
was not generated which lead to commit 36c01245eb "can: fix loss of CAN frames
in raw_rcv" - which forces the timestamp to be set in all CAN related skbuffs
by introducing several __net_timestamp() calls.
This forces e.g. out of tree drivers which are not using alloc_can{,fd}_skb()
to add __net_timestamp() after skbuff creation to prevent the frame loss fixed
in mainline Linux.
This patch removes the timestamp dependency and uses an atomic counter to
create an unique identifier together with the skbuff pointer.
Btw: the new skbcnt element introduced in struct can_skb_priv has to be
initialized with zero in out-of-tree drivers which are not using
alloc_can{,fd}_skb() too.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The previous change 3973c526ae (net: can: c_can: Disable pins when CAN
interface is down) causes a slight glitch on the pinctrl settings when used.
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
the device core will automatically set the default pins. This causes the pins
to be momentarily set to the default and then to the sleep state in
register_c_can_dev(). By adding an optional "enable" state, boards can set the
default pin state to be disabled and avoid the glitch when the switch from
default to sleep first occurs. If the "enable" state is not available
c_can_pinctrl_select_state() falls back to using the "default" pinctrl state.
[Roger Q] - Forward port to v4.2 and use pinctrl_get_select().
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
All the error messages in the driver but the ones from devm_clk_get() failures
use similar format. Make those two messages consitent with others.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Also print the error code when the request_irq() call fails in rcar_can_open(),
rewording the error message...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fix typo in the first error message printed by rcar_can_open().
Based on the original patch by Vladimir Barinov.
Fixes: 862e2b6af9 ("can: rcar_can: support all input clocks")
Reported-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Printing IRQ # using "%x" and "%u" unsigned formats isn't quite correct as
'ndev->irq' is of type *int*, so the "%d" format needs to be used instead.
While fixing this, beautify the dev_info() message in rcar_can_probe() a bit.
Fixes: fd1159318e ("can: add Renesas R-Car CAN driver")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
rcar_can_probe() regards 0 as a wrong IRQ #, despite platform_get_irq() that it
calls returns negative error code in that case. This leads to the following
being printed to the console when attempting to open the device:
error requesting interrupt fffffffa
because rcar_can_open() calls request_irq() with a negative IRQ #, and that
function naturally fails with -EINVAL.
Check for the negative error codes instead and propagate them upstream instead
of just returning -ENODEV.
Fixes: fd1159318e ("can: add Renesas R-Car CAN driver")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Conflicts:
drivers/net/ethernet/mellanox/mlx4/main.c
net/packet/af_packet.c
Both conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Manfred Schlaegl here
http://marc.info/?l=linux-netdev&m=143482089824232&w=2
commit 514ac99c64 "can: fix multiple delivery of a single CAN frame for
overlapping CAN filters" requires the skb->tstamp to be set to check for
identical CAN skbs.
As net timestamping is influenced by several players (netstamp_needed and
netdev_tstamp_prequeue) Manfred missed a proper timestamp which leads to
CAN frame loss.
As skb timestamping became now mandatory for CAN related skbs this patch
makes sure that received CAN skbs always have a proper timestamp set.
Maybe there's a better solution in the future but this patch fixes the
CAN frame loss so far.
Reported-by: Manfred Schlaegl <manfred.schlaegl@gmx.at>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch corrects addresses of acceptance filters. These registers are not in
use, but values should be correct. Tested with MCP2515 and am3352 and also
checked datasheets for MCP2515 and MCP2510.
Signed-off-by: Tomas Krcka <tomas.krcka@nkgroup.cz>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Four minor merge conflicts:
1) qca_spi.c renamed the local variable used for the SPI device
from spi_device to spi, meanwhile the spi_set_drvdata() call
got moved further up in the probe function.
2) Two changes were both adding new members to codel params
structure, and thus we had overlapping changes to the
initializer function.
3) 'net' was making a fix to sk_release_kernel() which is
completely removed in 'net-next'.
4) In net_namespace.c, the rtnl_net_fill() call for GET operations
had the command value fixed, meanwhile 'net-next' adjusted the
argument signature a bit.
This also matches example merge resolutions posted by Stephen
Rothwell over the past two days.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces a open coded variant of a "mailbox code" definition by an
existing define, improves code readability.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds a short documentation snippet about the mailbox organization as
it's regularly not correct in freescale's datasheets.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Flexcan V10 and newer are able to receive RTR frames in a MB. Older versions
are not. Those should use flexcan in FIFO mode.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In our department we are using some older Janz ICAN3-modules in our dekstop
pcs. There we have slightly different carrier boards than the janz-cmodio
supported in the kernel sources, called CAN-PCI2 with two submodules. But the
pci configuration regions are identical. So extending the supported pci devices
to the corresponding device ids is sufficient to get the drivers working.
* The old ICAN3-modules with firmware 1.28 need more then 250ms for the restart
after reset. I've increased the timeout to 500ms.
* The janz_ican3 module uses the raw can services of the Janz-firmware, this
means firmware must be ICANOS/2. Our ICAN3-modules are equipped with
CAL/CANopen-firmware, so I must use the appropriate commands for the layer
management services.
Te driver detects the firmware after module reset and selects the commands
matching the firmware. This affects the bus on/off-command
(ican3_set_bus_state) and the configuration of the bittiming
(ican3_set_bittiming). For better diagnostics the detected firmware string is
presented as sysfs attribute (fwinfo).
Signed-off-by: Andreas Gröger <andreas24groeger@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Using IDR_SRR in RXFIFO_ID to test for the presence of data is only
valid for standard frames. For extended frames the bit is always 1 and
IDR_RTR should be used instead. This patch switches the check to use
CAN_RTR_FLAG which is correctly set when reading the ID.
The patch also changes the DW1/DW2 to be read unconditionally, since
this is necessary to remove the frame from the RXFIFO.
Signed-off-by: Jeppe Ledet-Pedersen <jlp@gomspace.com>
Acked-by: Kedareswara rao Appana <appanad@xilinx.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If NO_DMA=y:
drivers/built-in.o: In function `grcan_free_dma_buffers':
grcan.c:(.text+0x2d7716): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `grcan_allocate_dma_buffers':
grcan.c:(.text+0x2d779c): undefined reference to `dma_alloc_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/asix_common.c
drivers/net/usb/sr9800.c
drivers/net/usb/usbnet.c
include/linux/usb/usbnet.h
net/ipv4/tcp_ipv4.c
net/ipv6/tcp_ipv6.c
The TCP conflicts were overlapping changes. In 'net' we added a
READ_ONCE() to the socket cached RX route read, whilst in 'net-next'
Eric Dumazet touched the surrounding code dealing with how mini
sockets are handled.
With USB, it's a case of the same bug fix first going into net-next
and then I cherry picked it back into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch silences the compiler warning:
drivers/net/can/usb/peak_usb/pcan_usb_fd.c: In function 'pcan_usb_fd_send_cmd':
drivers/net/can/usb/peak_usb/pcan_usb_fd.c:185:6: warning: 'err' may be used uninitialized in this function [-Wuninitialized]
by initialising the variable as 0.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The struct ems_cpc_msg describes the a message received from the USB device,
which uses little endian byte order. This patch marks the timestamp in struct
ems_cpc_msg accordingly.
Acked-by: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The device expects the CAN ID in little endian format.
Signed-off-by: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Change __raw accesors to endian agnostic versions to allow the driver
to work properly on big endian systems.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The hnd field of the structs does not need to be __le32: the
device just returns the value without using it itself.
Signed-off-by: Thomas Körper <thomas.koerper@esd.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add <ifname>-rxtx trigger, that will be activated both for tx
as rx events. This trigger mimics "activity" LED for Ethernet
devices.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use can-dev's unregister_candev() instead of directly calling
networking unregister_netdev(). While both are functionally
equivalent, unregister_candev() might do extra stuff in the
future than just calling networking layer unregistration code.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Return EPROBE_DEFER if Regulator returns EPROBE_DEFER
If the Flexcan driver is built into kernel and a regulator is used to
enable the CAN transceiver, the Flexcan driver may not use the regulator.
When initializing the Flexcan device with a regulator defined in the device
tree, but not initialized, the regulator subsystem returns EPROBE_DEFER, hence
the Flexcan init fails.
The solution for this is to return EPROBE_DEFER if regulator is not initialized
and wait until the regulator is initialized.
Signed-off-by: Andreas Werner <kernel@andy89.org>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Making sure that the bus-off state gets passed to can_change_state().
Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The PCAN USB (pro) FD adapters with firmware versions > 2.x support the
switching between ISO (default) and non-ISO conform bitstreams on the CAN bus.
The setting for the 2.x firmware adapters can be modified with the 'ip' tool
from the iproute2 package (option: fd-non-iso [on|off]).
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The PUCAN_CMD_RX_FRAME_(ENABLE|DISABLE) command has extended its purpose
and was therefore renamed to PUCAN_CMD_SET_(EN|DIS)_OPTION.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
smatch detected the following issue:
drivers/net/can/usb/gs_usb.c:904 gs_usb_probe() error:
potential null dereference 'dev'. (kzalloc returns null)
Add a check for null return from kzalloc and return -ENOMEM
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
USB endpoint's wMaxPacketSize field is an le16 entity. Use
appropriate le16_to_cpu macros to maintain endian independence.
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Current driver code arbitrarily assumes a max outstanding tx
value of 16 parallel transmissions. Meanwhile, the device
firmware provides its actual maximum inside its reply to the
CMD_GET_SOFTWARE_INFO message.
Under heavy tx traffic, if the interleaved transmissions count
increases above the limit reported by firmware, the firmware
breaks up badly, reports a massive list of internal errors, and
the candump traces hardly matches the actual frames sent and
received.
On the other hand, in certain models, the firmware can support
up to 48 tx URBs instead of just 16, increasing the driver
throughput by two-fold and reducing the possibility of -ENOBUFs.
Thus dynamically set the driver's max tx URBs value according
to firmware replies.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of tx queue wake-up events went missing due to the
outlined scenario below. Start state is a pool of 16 tx URBs,
active tx_urbs count = 15, with the netdev tx queue open.
CPU #1 [softirq] CPU #2 [softirq]
start_xmit() tx_acknowledge()
................ ................
atomic_inc(&tx_urbs);
if (atomic_read(&tx_urbs) >= 16) {
-->
atomic_dec(&tx_urbs);
netif_wake_queue();
return;
<--
netif_stop_queue();
}
At the end, the correct state expected is a 15 tx_urbs count
value with the tx queue state _open_. Due to the race, we get
the same tx_urbs value but with the tx queue state _stopped_.
The wake-up event is completely lost.
Thus avoid hand-rolled concurrency mechanisms and use a proper
lock for contexts and tx queue protection.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
