The tid which is given in addba/delba req event is not
just tid but also muxed with the assoc id (MSB 4 bits)
which can be used to determine the corresponding connected
station in softap mode. The actual tid is LSB 4 bits. Using
the tid as it is with rx_tid[] would result in OOB or invalid
memory access in AP mode.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will be used when initializing station specific aggregation
information.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch just groups connection specific aggregation information
from struct aggr_info into a new structure (struct aggr_info_conn)
so that, in softAP mode, this can be used when each connected station
is made to have it's own aggregation state.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The patch "ath6kl: create core.c" removes wiphy_free() from
ath6kl_cfg80211_cleanup() and misses to free wiphy in
ath6kl_sdio_remove(). This patch fixes this regression.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The timer which is used to flush rx aggregation frames needs to
be disabled when resetting the aggregation state. This is found
in code review.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
John Linville had to revert the part of USB support which was already
in ath6kl due to build problems in commit cb00ec382b ("ath6kl: revert
USB support"). Now that I fixed the build problems properly by adding
ath6kl_core.ko kernel module it's possible to add back the
(incomplete) USB support. This patch is a revert of John's patch and
adds back the USB code which as already in ath6kl, only difference
being minor changes in Makefile and adapting usb.c to new core
function names.
Note that USB support in ath6kl is not complete yet. This code only
makes it possible to boot firmware but as HTC layer does not yet
support USB it's not possible to send any WMI commands nor data
packets to the firmware. That will be added soon.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Now ath6kl is ready for splitting core code to ath6kl_core.ko module.
This also makes it possible to link both sdio and usb code to kernel
at the same time, which earlier failed miserably.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
That way it's possible to not export debug_mask outside the upcoming
ath6kl_core.ko and that makes it easier to ath6kl_core.ko in the
following patch.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We don't need it as debug calls already have a log level and compiler
should be smart enough to optimise away the code when ath6kl debug code
is not enabled. Also it makes it easier to abstract core code to
ath6kl_core.ko.
In ath6kl_dump_registers() I had to change the debug level from ANY to IRQ
as I removed the AR_DBG_LVL_CHECK() check before calling the function.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently core functions are spread between various files, group all
the functions into file and rename the functions to follow the style
used elsewhere in the driver. This will make it easier to a separate core
module.
Also fix a bug where wiphy is freed too early.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add ATH6KL_CONF_UART_DEBUG which is set whenever uart_debug module
parameter is enabled. This way we can keep the uart_debug parameter
static when core.c file is introduced.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Group them together and change the naming to follow the common style in
ath6kl. No functional changes.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add testmode 2 for 6003 ART. When you insmod ath6kl_sdio.ko testmode=2, ath6kl
will load ART firmware utf.bin and testscript nullTestFlow.bin. These files
should be put in the firmware folder.
kvalo: add "ath6kl:" to the title, word wrap the commit log and remove
extra line in the code
Signed-off-by: Alex Yang <xiaojuny@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Before I commited patch c1762a3fe ("ath6kl: Add support for uAPSD") I
did a minor change how up variable is initialised in
ath6kl_process_uapsdq(). But I was sloppy and caused this compiler
warning:
txrx.c:88:5: warning: 'up' may be used uninitialized in this function
Revert my change to fix the warning.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
As drivers/net/wireless/ath/Makefile contains the flag to enable
endian checks there's no need to have it in ath6kl makefile anymore.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit c8f44affb7 ("net: introduce and use netdev_features_t for
device features sets") added netdev_features_t to ndo_set_features.
Change ath6kl to use the new type.
This fixes a warning:
ath6kl/main.c:1170: warning: initialization from incompatible pointer type
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl_read_fwlogs() assigns the value zero to the variable 'ret'
at the time of declaration. Later, return value of ath6kl_diag_read32()
repalces the init value. Hence removing useless zero assignment.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* A new APSD power save queue is added in the station structure.
* When a station has APSD capability and goes to power save, the frame
designated to the station will be buffered in APSD queue.
* When the host receives a frame which the firmware marked as trigger,
host delivers the buffered frame from the APSD power save queue.
Number of frames to deliver is decided by MAX SP length.
* When a station moves from sleep to awake state, all frames buffered
in APSD power save queue are sent to the firmware.
* When a station is disconnected, all frames bufferes in APSD power save
queue are dropped.
* When the host queues the first frame to the APSD queue or removes the
last frame from the APSD queue, it is indicated to the firmware using
WMI_AP_APSD_BUFFERED_TRAFFIC_CMD.
kvalo: fix buggy handling of sks queues, made it more obvious
the user priority when wmm is disabled, remove unneed else block and
combined some variable declarations
Signed-off-by: Thirumalai Pachamuthu <tpachamu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch addresses a few problems with the commit:
"ath6kl: Implement support for listen interval from userspace"
* The debugfs file required for reading/writing the listen interval
wasn't created. Fix this.
* The interface index was being hardcoded to zero. Fix this.
* Two separate parameters, "listen_interval_time and listen_interval_beacons"
were being used. This fails to work as expected because the FW assigns
higher precedence to "listen_interval_beacons" and "listen_interval_time"
ends up being never used at all.
To handle this, fix the host driver to exclusively use listen interval
based on units of beacon intervals.
To set the listen interval, a user would now do something like this:
echo "10" > /sys/kernel/debug/ieee80211/*/ath6kl/listen_interval
kvalo: fix two checkpatch warnings
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This prevents 'comp_pktq' from being used in an
incorrect manner.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
'params' is already used earlier and there is no point
in checking for a NULL condition again.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently this race is handled but in a messy way an atomic
variable is being checked in a loop which sleeps upto ms
in every iteration. Remove this logic and use a mutex
to make sure irq is not disabled when irq handling is in
progress.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Otherwise if (ielen <= ATH6KL_MAX_IE) is dead code. It looks safe to
change the type of ielen from u8 to size_t instead of removing this
if check, this ielen can have the length of more than one ies in future.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In ath6kl_reset_device(), since control can never reach switch..case
when the target_type is neither TARGET_TYPE_AR6003 nor TARGET_TYPE_AR6004,
remove the default option of switch statement.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are maximum of seven multicast filter are supported
by hw. When the requested number of filters exceeds the
maximum supported one, multicast filtering is completely
disabled, the requested filters will be configured in
firmware and the only multicast frames that host is interested
in will be passed to host for further processing otherwise.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
The ath6kl driver is causing build failures when the ath6kl bits are
not built as modules. A better fix is forthcoming in a future release,
but for now lets revert the problematic code.
This reverts the following commits:
fde57764efd70385a26a59d954dda4
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath6kl no longer knows what it is transmitting through
cfg80211_testmode, and simply passes opaque buffers between userspace
and the firmware. Leave the CONT_RX enum for backwards compatibility.
kvalo: change ATH6KL_TM_CMD_RX_REPORT to return -EOPNOTSUPP
Signed-off-by: Thomas Pedersen <twpedersen@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Less-than-zero comparison of an unsigned value is never true.
kvalo: remove WMI_MIN_KEY_INDEX altogether, it's useless
Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To enable firmware debug messages through uart interface,
modprobe ath6kl_sdio uart_debug=1.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The change enables offloading TCP checksum calculation to firmware.
There are still some issues with the checksum offload so better to
disable it by default until the issues are resolved.
To enable TCP checksum offload for tx and rx paths, use
the ethtool as follows:
ethtool -K <interface> tx on
ethtool -K <interface> rx on
To disable TCP checksum offload, for tx and rx paths, use
the ethtool as follows:
ethtool -K <interface> tx off
ethtool -K <interface> rx off
kvalo: indentation changes
Signed-off-by: Rishi Panjwani <rpanjwan@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is needed to fix current hostapd/wpa_supplicant AP operations for
frame registration. P2P GO mode already advertised these, but AP mode
was forgotten and could not be used after the hostapd/wpa_supplicant
frame registration changes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
hostapd/wpa_supplicant AP mode uses this operation to flush the station
entries. Implement this in ath6kl to avoid unnecessary warnings from
NL80211_CMD_DEL_STATION failing.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
As firmware starting from 3.2.0.12 has some API changes and doesn't work
with older versions of ath6kl we need to bump up the API version. This
way we don't break anything.
Also store which version of API is used and print that during boot:
ath6kl: ar6003 hw 2.1.1 sdio fw 3.2.0.13 api 3
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently ath6kl has just hardcoded paths to each firmware file. Change
this more dynamic by separating the the directory and file name from each
other. That way it's easier to dynamically create full paths to firmware and
code looks better. And now it's possible to remove a function needed by
devicetree code.
While at it add a structure inside struct ath6kl_hw to contain all
firmware names. I deliberately omitted board file support as
those will be handled later.
This is needed for firmware API 3.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware ARP module requires own IP addr in order to respond
to the outside world when the target is in WOW suspend state.
At present, firmware ARP module has capability to hold 2 IP addr.
So, WOW mode will be disabled if the total IP addr configured in
net_dev for our device is greater than firmware limit (MAX_IP_ADDRS)
which is 2 at this moment.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Thirumalai Pachamuthu <tpachamu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In this way, caller is free to pass only the value of IP addr
to configure.
In addition to this,
* 'ips' variable data type in struct wmi_set_ip_cmd is changed
from __le32 to __be32 in order to match network byte order.
* ipv4_is_multicast() is used to validate multicast ip addr.
* New argument if_idx is added to supply correct vif index
to ath6kl_wmi_cmd_send().
This will be used in the next patch.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Thirumalai Pachamuthu <tpachamu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Empty IE buffer means that the new association is not supposed to
include extra IEs. Make sure any previously configured (Re)Association
Request frame IEs get cleared in such a case. This is based on a patch
from Shuibing.
Cc: Dai Shuibing <shuibing@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is to avoid the scenario where the bss entry of the AP got
expired when reporting roaming event to current AP. As the bss
entry for the current bss is available in driver, pass this bss
to cfg80211. This fixes WARNING: at net/wireless/sme.c:586.
This patch depends on the following patch in cfg80211
"cfg80211: Fix race in bss timeout".
Reported-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
DaveM said:
Please, this kind of stuff rots forever and not using bool properly
drives me crazy.
Joe Perches <joe@perches.com> gave me the spatch script:
@@
bool b;
@@
-b = 0
+b = false
@@
bool b;
@@
-b = 1
+b = true
I merely installed coccinelle, read the documentation and took credit.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables support for doing P2P management operations like device
discovery on top of a station interface. After group formation, the station
interface will become a P2P GO/client interface as the case may be.
This feature requires modifications to a couple of existing WMI structures and
therefore new command ids and structures have been defined in order to be
compatible with older firmware versions and other chips. The exception here is
the wmi_connect_cmd. Adding a new field to the end of the structure will not
cause any issues with previous firmware versions since firmware only checks for
minimum length of the command. The other structures are of variable length,
hence it was not possible to add new fields to the end.
The new command ids have to be added to the end of enum wmi_cmd_id, so it has
updated to match the firmware.
The driver will support both the 'old' and the 'new' commands for a while by
checking the firmware capabilities.
Signed-off-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
AR6003 family use uart_tx=8 and refclk=26Mhz by default, and AR6004 family
uses different uart_tx pin and could also support various xtal source,
moves these per hw configuration.
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl firmware supports scheduled scan functionality with the wow ssid
filter. But the firmware does not send any events after scan results
so I had to add a timer which notifies about new scan results.
Sched scan needs firmware version 3.2.0.6 or later. If firmware doesn't
support sched scan the driver will not enable the feature.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For some strange reason I used ALIGN() to calculate index to the
buffer. That is totally bogus and wouldn't work when it tried to read
the second bit. Fix it by removing the ALIGN() altogether.
Also check that ie_len is not too short.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This way it's possible to keep all disconnect logic in one function and
easier to add new functionality, like stopping scheduled scan.
There are some changes to commands called during network interface close,
but there should not be any visible changes in functionality.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There's a workaround in ath6kl_cfg80211_stop() which emits disconnected
even when sme_state was disconnected. This is legacy from the old
staging driver and I can't repoduce the old problem anymore. I assume the
bug got fixed while the driver was cleaned up so let's get
rid of the hack.
This makes it possible to call ath6kl_cfg80211_stop from ath6kl_close()
which happens in a followup patch.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is needed to allow WAPI AP to configure the initial group key
to the target in the same way as is done with TKIP/CCMP. This
fixes broadcast data frame delivery with the initial group key.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The maximum number of clients which ath6kl can support in AP mode
is 10. The limitation of 8 connections is only for older chipsets
which ath6kl does not support.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was only initialised but not used anywhere. Also remove two defines
which ended up unused after this change.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl assumed cfg80211 passed to us power in dBm but it is in mBm.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The return value of snprintf() is the number of bytes which would
have been copied if there was enough space, but we want the number of
bytes actually copied. The scnprintf() function does this.
Also in theory, a %u can take take 10 digits so we may as well make
the buffer larger as well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently mac80211 implements these for all devices,
but given restrictions of some devices that isn't
really true, so prepare for being able to remove the
capability for some mac80211 devices.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware crashes while starting Soft AP in 32 bit x86 platform.
The reason is that the single dma buffer (ar_sdio->dma_buffer)
is used in ath6kl_sdio_read_write_sync() for unaligned buffer
handling and this function is called in the multiple context
at the same time. So, finally hits dma buffer corruption and
firmware crash.
Mutex is used to protect dma buffer to avoid data corruption.
Spin lock can not used to fix this issue since mmc stack
read/write calls may for sleep.
Observed this issue with recently commited patch
"ath6kl: Claim sdio function only at appropriate places"
861dd058f4
kvalo: change name of mutex to more descriptive and add a comment
about what it protects
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There is an unlock missing on this error path.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The maximum number of supported virtual interfaces are 3.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently the max number of vifs which can be used for non-p2p
mode is determined in ath6kl_core_alloc(). But the maximum
supported vifs are parsed from firmware IE in ath6kl_fetch_fw_api2()
which would happen after ath6kl_core_alloc().
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This modparam was introduced to enable non-p2p mode operation
on two virtual interfaces. It does not seem to be necessary to
have a separate module parameter to do that. Instead, this option
can be enabled when any one of the interfaces is not going to be
used for p2p (ath6kl_p2p).
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath6kl responds to probe-requests in HW while operating as an AP. It
supports offloading exclusions to support the WPS, WPS2, P2P and
802.11u protocols.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When operating AP interface is brough down the mode is reset to
STA. This STA will be reconfigured into AP mode when the interface
is brought up again. This sequence will be successful only when
change_virtual_intf() returns with no error, but there is a
check in this callback which does the type change only when
that interface is active. This callback does nothing more
than saving the new interface type to vif and wdev, so the
sanity check for interface state and wmi state is not necessary.
This makes the AP interface functional again after interface down/up.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Connect control flag CONNECT_WPS_FLAG has to be cleared
by default even if the driver receives zero length IE
from cfg80211.
Otherwise this flag would be always set after WPS exchange
which would lead wpa_supplicant to fail to connect with
the received WPS credentials. This issue is observed only
in OPEN security.
kvalo: use cfg80211 instead of CFG in the commit log
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When adding ar6004 SDIO support I forgot to add corresponding
MODULE_FIRMWARE() definitions to sdio.c.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Part of ath6kl uses "REV3" style of naming hardware versions and elsewhere
"hw 2.1.1" is used instead for the same version. This is confusing, use
the latter term everywhere.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To make it easier to print name for each hardware type. Also move the hw
info print to ath6kl_init_hw_start() which is more logical place for it.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Board data address can change between firmwares so we need to read that
from the firmware image.
Also fix debug log for the patch address to print the address in hex.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is to make it configurable by firmware IEs. Also determine if we need
to write or read the board address to the chip by checking if board address
is set or not.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Having separate defines, in a different file, makes it difficult to read
the actual values. As we are just setting named fields in a struct
the defines don't make any sense anymore.
There are no functional changes, only moving of constants.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
OPEN_AUTH is passed as dot11_auth_mode by default, this would
affect the AP mode when configured with shared authentication
type. Assign appropriate auth type to fix this from driver.
A patch in wpa_supplicant (wpa_supplicant: Set configured auth_algs)
is also needed to fix this.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
vif->def_txkey_index is set to key_index in ath6kl_cfg80211_add_key().
If the interface is configured with multiple static wep keys,
vif->def_txkey_index would be holding the index of the last key configured,
not the default tx key index. Remove this unnecessary default key index setting
in ath6kl_cfg80211_add_key() to configure the right key index in WEP thereby
make it work when multiple wep keys are configured.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Now two modules are built, ath6kl_sdio.ko and ath6kl_usb.ko. But the USB
module isn't fully functional yet as HTC layer is missing support and
that's why it's marked as experimental for now.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
As HTC layer doesn't support USB devices return an error if that happens.
USB support will be added to HTC in the future, this is just a temporary
solution.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add USB support for ar6004. Currently only firmware can be booted,
no commands can be sent to firmware yet as HTC layer doesn't work
with USB yet.
Based on patches by Kevin Fang.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In some rare cases core code needs to know what hif type is used. Add
a field to struct ath6kl to denote that. Hopefully this is just a
temporary solution.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add support for AR6004 SDIO. Tested scan, association (open mode) and
ping.
kvalo: change commit log a bit, drop board address changes
Signed-off-by: Naveen Gangadharan <ngangadh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is preparation for USB support which will have different diag
commands.
Based on code by Kevin Fang.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The firmware expects the minimum length of
WMI_SEND_PROBE_RESPONSE_CMDID to be 13. However, when the device is a
P2P GO and it needs to send a probe response to a non-P2P client,
there are no P2P IEs to be added, and therefore the length of the WMI
command is 12. This command gets rejected by the firmware. To fix
this, add an extra byte to satisfy the minimum length requirement.
Signed-off-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When the connect event is received from the target in IBSS mode,
cfg80211_ibss_joined() is called without informing BSS info to
cfg80211 layer which internally hits the below WARN_ON message.
WARNING: at net/wireless/ibss.c:33 __cfg80211_ibss_joined+0x153/0x180 [cfg80211]()
[..]
[ 4916.845878] Call Trace:
[ 4916.845889] [<c10427d2>] warn_slowpath_common+0x72/0xa0
[ 4916.845905] [<f8bccc63>] ? __cfg80211_ibss_joined+0x153/0x180 [cfg80211]
[ 4916.845918] [<f8bccc63>] ? __cfg80211_ibss_joined+0x153/0x180 [cfg80211]
[ 4916.845923] [<c1042822>] warn_slowpath_null+0x22/0x30
[ 4916.845934] [<f8bccc63>] __cfg80211_ibss_joined+0x153/0x180 [cfg80211]
[ 4916.845941] [<c1025108>] ? default_spin_lock_flags+0x8/0x10
[ 4916.845952] [<f8bb7fcd>] cfg80211_process_rdev_events+0x19d/0x220 [cfg80211]
[ 4916.845962] [<f8bb669b>] cfg80211_event_work+0x2b/0x50 [cfg80211]
[ 4916.845968] [<c105aae6>] process_one_work+0x116/0x3c0
[ 4916.845977] [<f8bb6670>] ? cfg80211_get_dev_from_info+0x40/0x40 [cfg80211]
[ 4916.845982] [<c105cdf0>] worker_thread+0x140/0x3b0
[ 4916.845986] [<c105ccb0>] ? manage_workers+0x1f0/0x1f0
[ 4916.845991] [<c1060c64>] kthread+0x74/0x80
[ 4916.845995] [<c1060bf0>] ? kthread_worker_fn+0x160/0x160
[ 4916.846001] [<c14e7bbe>] kernel_thread_helper+0x6/0x10
[ 4916.846005] ---[ end trace 769254924e409367 ]---
This patch make sures that BSS info is delivered via cfg80211_inform_bss()
to cfg80211 in advance before intimating IBSS status to cfg80211.
In addition to this, one debug message is also added to know
ad-hoc mode status (creator/joiner).
kvalo: change subject
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
"ath6kl: Maintain virtual interface in a list" mistakenly stops the
netq only when the mode is ibss. This causes packet drops in sta mode
when the available cookies (buffer abstraction in ath6kl and also used
for tx throttling) runs out for the highest priority traffic. This patch
just fixes this regression though the original code may still need fixes
which can be addressed in separate patches.
Reported-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When buffer alignmnet is applied, the data pointer of skb taken from
cookie will no longer point to the first byte of the actual data.
But the skb->data pointer is used in ath6kl_tx_complete() to get
the index of the virtual interface which will not give the correct
interface index and sometimes may give the following WARN_ON() message.
Use packet->buf instead of skb->data to fix this.
WARNING: at drivers/net/wireless/ath/ath6kl/wmi.c:88 ath6kl_get_vif_by_index+0x5b/0x60 [ath6kl]()
Hardware name: 2842K3U
Modules linked in: ath6kl mmc_block cfg80211 binfmt_misc ppdev nfs nfsd lockd nfs_acl auth_rpcgss sunrpc exportfs snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_intel
+snd_hda_codec snd_hwdep snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_dummy thinkpad_acpi snd_seq_oss snd_seq_midi snd_rawmidi joydev fbcon tileblit font bitblit softcursor
+snd_seq_midi_event snd_seq snd_timer snd_seq_device i915 uvcvideo drm_kms_helper drm psmouse serio_raw snd i2c_algo_bit sdhci_pci videodev intel_agp soundcore intel_gtt jmb38x_ms
+memstick sdhci snd_page_alloc nvram lp parport agpgart video ahci r8169 mii libahci [last unloaded: ath6kl]
Pid: 15482, comm: kworker/u:1 Tainted: G W 3.1.0-rc10-wl+ #2
Call Trace:
[<c0144d72>] warn_slowpath_common+0x72/0xa0
[<fb7c94fb>] ? ath6kl_get_vif_by_index+0x5b/0x60 [ath6kl]
[<fb7c94fb>] ? ath6kl_get_vif_by_index+0x5b/0x60 [ath6kl]
[<c0144dc2>] warn_slowpath_null+0x22/0x30
[<fb7c94fb>] ath6kl_get_vif_by_index+0x5b/0x60 [ath6kl]
[<fb7c7028>] ath6kl_tx_complete+0x128/0x4d0 [ath6kl]
[<c04df920>] ? mmc_request_done+0x80/0x80
[<fb7b9e2e>] htc_tx_complete+0x5e/0x70 [ath6kl]
[<c05e4cf6>] ? _raw_spin_unlock_bh+0x16/0x20
[<fb7ce588>] ? ath6kl_sdio_scatter_req_add+0x48/0x60 [ath6kl]
[<fb7b9f42>] htc_async_tx_scat_complete+0xb2/0x120 [ath6kl]
[<fb7ce9e7>] ath6kl_sdio_scat_rw+0x87/0x370 [ath6kl]
[<c0101e12>] ? __switch_to+0xd2/0x190
[<c01397b5>] ? finish_task_switch+0x45/0xd0
[<c05e272e>] ? __schedule+0x3ae/0x8b0
[<fb7cf00a>] ath6kl_sdio_write_async_work+0x4a/0xf0 [ath6kl]
[<c015d266>] process_one_work+0x116/0x3c0
[<fb7cefc0>] ? ath6kl_sdio_read_write_sync+0xb0/0xb0 [ath6kl]
[<c015f5b0>] worker_thread+0x140/0x3b0
[<c015f470>] ? manage_workers+0x1f0/0x1f0
[<c0163424>] kthread+0x74/0x80
[<c01633b0>] ? kthread_worker_fn+0x160/0x160
[<c05ebdc6>] kernel_thread_helper+0x6/0x10
Reported-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
