Currently powernv reboot and shutdown requests just leave secondaries
to do their own things. This is undesirable because they can trigger
any number of watchdogs while waiting for reboot, but also we don't
know what else they might be doing -- they might be causing trouble,
trampling memory, etc.
The opal scheduled flash update code already ran into watchdog problems
due to flashing taking a long time, and it was fixed with 2196c6f1ed
("powerpc/powernv: Return secondary CPUs to firmware before FW update"),
which returns secondaries to opal. It's been found that regular reboots
can take over 10 seconds, which can result in the hard lockup watchdog
firing,
reboot: Restarting system
[ 360.038896709,5] OPAL: Reboot request...
Watchdog CPU:0 Hard LOCKUP
Watchdog CPU:44 detected Hard LOCKUP other CPUS:16
Watchdog CPU:16 Hard LOCKUP
watchdog: BUG: soft lockup - CPU#16 stuck for 3s! [swapper/16:0]
This patch removes the special case for flash update, and calls
smp_send_stop in all cases before calling reboot/shutdown.
smp_send_stop could return CPUs to OPAL, the main reason not to is
that the request could come from a NMI that interrupts OPAL code,
so re-entry to OPAL can cause a number of problems. Putting
secondaries into simple spin loops improves the chances of a
successful reboot.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Bring in yet another series that touches KVM code, and might need to
be merged into the kvm-ppc branch to resolve conflicts.
This required some changes in pnv_power9_force_smt4_catch/release()
due to the paca array becomming an array of pointers.
Change the paca array into an array of pointers to pacas. Allocate
pacas individually.
This allows flexibility in where the PACAs are allocated. Future work
will allocate them node-local. Platforms that don't have address limits
on PACAs would be able to defer PACA allocations until later in boot
rather than allocate all possible ones up-front then freeing unused.
This is slightly more overhead (one additional indirection) for cross
CPU paca references, but those aren't too common.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that we have the security flags we can significantly simplify the
code in pnv_setup_rfi_flush(), because we can use the flags instead of
checking device tree properties and because the security flags have
pessimistic defaults.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that we have feature flags for security related things, set or
clear them based on what we see in the device tree provided by
firmware.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some versions of firmware will have a setting that can be configured
to disable the RFI flush, add support for it.
Fixes: 6e032b350c ("powerpc/powernv: Check device-tree for RFI flush settings")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
New device-tree properties are available which tell the hypervisor
settings related to the RFI flush. Use them to determine the
appropriate flush instruction to use, and whether the flush is
required.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We have some dependencies & conflicts between patches in fixes and
things to go in next, both in the radix TLB flush code and the IMC PMU
driver. So merge fixes into next.
The call to /proc/cpuinfo in turn calls cpufreq_quick_get() which
returns the last frequency requested by the kernel, but may not
reflect the actual frequency the processor is running at. This patch
makes a call to cpufreq_get() instead which returns the current
frequency reported by the hardware.
Fixes: fb5153d05a ("powerpc: powernv: Implement ppc_md.get_proc_freq()")
Signed-off-by: Shriya <shriyak@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some Power9 revisions can run in a mode where TM operates without
suspended state. If we find ourself on a CPU that might be in this
mode, we query OPAL to check, and if so we reenable TM in CPU
features, and enable a new user feature to signal to userspace that we
are in this mode.
We do not enable the "normal" user feature, PPC_FEATURE2_HTM, but we
do enable PPC_FEATURE2_HTM_NOSC because that indicates to userspace
that the kernel will abort transactions on syscall entry, which is
true regardless of the suspend mode.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Memory hot unplug on PowerNV radix hosts is broken. Our memory block
size is 256MB but since we map the linear region with very large
pages, each pte we tear down maps 1GB.
A hot unplug of one 256MB memory block results in 768MB of memory
getting unintentionally unmapped. At this point we are likely to oops.
Fix this by increasing our memory block size to 1GB on PowerNV radix
hosts.
Fixes: 4b5d62ca17 ("powerpc/mm: add radix__remove_section_mapping()")
Cc: stable@vger.kernel.org # v4.11+
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
That will allow OPAL to configure the CPU in an optimal way.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This merges the arch part of the XIVE support, leaving the final commit
with the KVM specific pieces dangling on the branch for Paul to merge
via the kvm-ppc tree.
The XIVE interrupt controller is the new interrupt controller
found in POWER9. It supports advanced virtualization capabilities
among other things.
Currently we use a set of firmware calls that simulate the old
"XICS" interrupt controller but this is fairly inefficient.
This adds the framework for using XIVE along with a native
backend which OPAL for configuration. Later, a backend allowing
the use in a KVM or PowerVM guest will also be provided.
This disables some fast path for interrupts in KVM when XIVE is
enabled as these rely on the firmware emulation code which is no
longer available when the XIVE is used natively by Linux.
A latter patch will make KVM also directly exploit the XIVE, thus
recovering the lost performance (and more).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Fixup pr_xxx("XIVE:"...), don't split pr_xxx() strings,
tweak Kconfig so XIVE_NATIVE selects XIVE and depends on POWERNV,
fix build errors when SMP=n, fold in fixes from Ben:
Don't call cpu_online() on an invalid CPU number
Fix irq target selection returning out of bounds cpu#
Extra sanity checks on cpu numbers
]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With this we have on powernv and pseries /proc/cpuinfo reporting
timebase : 512000000
platform : PowerNV
model : 8247-22L
machine : PowerNV 8247-22L
firmware : OPAL
MMU : Hash
Reviewed-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 2965faa5e0 ("kexec: split kexec_load syscall from kexec core
code") introduced CONFIG_KEXEC_CORE so that CONFIG_KEXEC means whether
the kexec_load system call should be compiled-in and CONFIG_KEXEC_FILE
means whether the kexec_file_load system call should be compiled-in.
These options can be set independently from each other.
Since until now powerpc only supported kexec_load, CONFIG_KEXEC and
CONFIG_KEXEC_CORE were synonyms. That is not the case anymore, so we
need to make a distinction. Almost all places where CONFIG_KEXEC was
being used should be using CONFIG_KEXEC_CORE instead, since
kexec_file_load also needs that code compiled in.
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It is now called right after platform probe, so the probe function
can just do the job.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We no long need the machine type that early, so we can move probe_machine()
to after the device-tree has been expanded. This will allow further
consolidation.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We move it into early_mmu_init() based on firmware features. For PS3,
we have to move the setting of these into early_init_devtree().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
pnv_init_idle_states() discovers supported idle states from the
device tree and does the required initialization. Set power_save
function pointer only after this initialization is done
Otherwise on machines which don't support nap, eg. Power9, the kernel
will crash when it tries to nap.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds routines for early setup for radix. We use device tree
property "ibm,processor-radix-AP-encodings" to find supported page
sizes. If we don't find the above we consider 64K and 4K as supported
page sizes.
We do map vmemap using 2M page size if we can. The linear mapping is
done such that we use required page size for that range. For example
memory of 3.5G is mapped such that we use 1G mapping till 3G range and
use 2M mapping for the rest.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Long ago, only in the lab, there was OPALv1 and OPALv2. Now there is
just OPALv3, with nobody ever expecting anything on pre-OPALv3 to
be cared about or supported by mainline kernels.
So, let's remove FW_FEATURE_OPALv3 and instead use FW_FEATURE_OPAL
exclusively.
Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
OPALv2 only ever existed in the lab and didn't escape to the world.
All OPAL systems in the wild are OPALv3.
The probability of there being an OPALv2 system still powered on
anywhere inside IBM is approximately zero, let alone anyone
expecting to run mainline kernels.
So, start to remove references to OPALv2.
Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Always include a timeout when waiting for secondary cpus to enter OPAL
in the kexec path, rather than only when crashing.
Signed-off-by: Samuel Mendoza-Jonas <sam.mj@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On powernv secondary cpus are returned to OPAL, and will then enter
the target kernel in big-endian. However if it is set the HILE bit
will persist, causing the first exception in the target kernel to be
delivered in litte-endian regardless of the current endianness.
If running on top of OPAL make sure the HILE bit is reset once we've
finished waiting for all of the secondaries to be returned to OPAL.
Signed-off-by: Samuel Mendoza-Jonas <sam.mj@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Simplify the dma_get_required_mask call chain by moving it from pnv_phb to
pci_controller_ops, similar to commit 763d2d8df1 ("powerpc/powernv:
Move dma_set_mask from pnv_phb to pci_controller_ops").
Previous call chain:
0) call dma_get_required_mask() (kernel/dma.c)
1) call ppc_md.dma_get_required_mask, if it exists. On powernv, that
points to pnv_dma_get_required_mask() (platforms/powernv/setup.c)
2) device is PCI, therefore call pnv_pci_dma_get_required_mask()
(platforms/powernv/pci.c)
3) call phb->dma_get_required_mask if it exists
4) it only exists in the ioda case, where it points to
pnv_pci_ioda_dma_get_required_mask() (platforms/powernv/pci-ioda.c)
New call chain:
0) call dma_get_required_mask() (kernel/dma.c)
1) device is PCI, therefore call pci_controller_ops.dma_get_required_mask
if it exists
2) in the ioda case, that points to pnv_pci_ioda_dma_get_required_mask()
(platforms/powernv/pci-ioda.c)
In the p5ioc2 case, the call chain remains the same -
dma_get_required_mask() does not find either a ppc_md call or
pci_controller_ops call, so it calls __dma_get_required_mask().
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Previously, dma_set_mask() on powernv was convoluted:
0) Call dma_set_mask() (a/p/kernel/dma.c)
1) In dma_set_mask(), ppc_md.dma_set_mask() exists, so call it.
2) On powernv, that function pointer is pnv_dma_set_mask().
In pnv_dma_set_mask(), the device is pci, so call pnv_pci_dma_set_mask().
3) In pnv_pci_dma_set_mask(), call pnv_phb->set_dma_mask() if it exists.
4) It only exists in the ioda case, where it points to
pnv_pci_ioda_dma_set_mask(), which is the final function.
So the call chain is:
dma_set_mask() ->
pnv_dma_set_mask() ->
pnv_pci_dma_set_mask() ->
pnv_pci_ioda_dma_set_mask()
Both ppc_md and pnv_phb function pointers are used.
Rip out the ppc_md call, pnv_dma_set_mask() and pnv_pci_dma_set_mask().
Instead:
0) Call dma_set_mask() (a/p/kernel/dma.c)
1) In dma_set_mask(), the device is pci, and pci_controller_ops.dma_set_mask()
exists, so call pci_controller_ops.dma_set_mask()
2) In the ioda case, that points to pnv_pci_ioda_dma_set_mask().
The new call chain is
dma_set_mask() ->
pnv_pci_ioda_dma_set_mask()
Now only the pci_controller_ops function pointer is used.
The fallback paths for p5ioc2 are the same.
Previously, pnv_pci_dma_set_mask() would find no pnv_phb->set_dma_mask()
function, to it would call __set_dma_mask().
Now, dma_set_mask() finds no ppc_md call or pci_controller_ops call,
so it calls __set_dma_mask().
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
All users of the old opal events notifier have been converted over to
the irq domain so remove the event notifier functions.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This is a cleanup patch; doesn't change any functionality. Moves
all cpuidle related code from setup.c to a new file.
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
[mpe: Fix the SMP=n build by including asm/smp.h in idle.c]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The powernv code has some conditional support for running on bare metal
machines that have no OPAL firmware, but provide RTAS.
No released machines ever supported that, and even in the lab it was
just a transitional hack in the days when OPAL was still being
developed.
So remove the code.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>
We currently read the information about idle states from the device
tree, so as to find out the CPU idle states supported by the platform.
Use the of_property_read/count_xxx() APIs, which handle endian
conversions for us, and mean we don't need any endian annotations in the
code.
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
LPCR_PECE1 bit controls whether decrementer interrupts are allowed to
cause exit from power-saving mode. While waking up from winkle, restoring
LPCR with LPCR_PECE1 set (i.e Decrementer interrupts allowed) can cause
issue in the following scenario:
- All the threads in a core are offlined. The core enters deep winkle.
- Spurious interrupt wakes up a thread in the core. Here LPCR is restored
with LPCR_PECE1 bit set.
- Since it was a spurious interrupt on a offline thread, the thread clears
the interrupt and goes back to winkle.
- Here before the thread executes winkle and puts the core into deep winkle,
if a decrementer interrupt occurs on any of the sibling threads in the core
that thread wakes up.
- Since in offline loop we are flushing interrupt only in case of external
interrupt, the decrementer interrupt does not get flushed. So at this stage
the thread is stuck in this is loop of waking up at 0x100 due to decrementer
interrupt, not flushing the interrupt as only external interrupts get flushed,
entering winkle, waking up at 0x100 again.
Fix this by programming PORE to restore LPCR with LPCR_PECE1 bit
cleared when waking up from winkle.
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Winkle is a deep idle state supported in power8 chips. A core enters
winkle when all the threads of the core enter winkle. In this state
power supply to the entire chiplet i.e core, private L2 and private L3
is turned off. As a result it gives higher powersavings compared to
sleep.
But entering winkle results in a total hypervisor state loss. Hence the
hypervisor context has to be preserved before entering winkle and
restored upon wake up.
Power-on Reset Engine (PORE) is a dedicated engine which is responsible
for powering on the chiplet during wake up. It can be programmed to
restore the register contests of a few specific registers. This patch
uses PORE to restore register state wherever possible and uses stack to
save and restore rest of the necessary registers.
With hypervisor state restore things fall under three categories-
per-core state, per-subcore state and per-thread state. To manage this,
extend the infrastructure introduced for sleep. Mainly we add a paca
variable subcore_sibling_mask. Using this and the core_idle_state we can
distingush first thread in core and subcore.
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Deep idle states like sleep and winkle are per core idle states. A core
enters these states only when all the threads enter either the
particular idle state or a deeper one. There are tasks like fastsleep
hardware bug workaround and hypervisor core state save which have to be
done only by the last thread of the core entering deep idle state and
similarly tasks like timebase resync, hypervisor core register restore
that have to be done only by the first thread waking up from these
state.
The current idle state management does not have a way to distinguish the
first/last thread of the core waking/entering idle states. Tasks like
timebase resync are done for all the threads. This is not only is
suboptimal, but can cause functionality issues when subcores and kvm is
involved.
This patch adds the necessary infrastructure to track idle states of
threads in a per-core structure. It uses this info to perform tasks like
fastsleep workaround and timebase resync only once per core.
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Originally-by: Preeti U. Murthy <preeti@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: linux-pm@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The secondary threads should enter deep idle states so as to gain maximum
powersavings when the entire core is offline. To do so the offline path
must be made aware of the available deepest idle state. Hence probe the
device tree for the possible idle states in powernv core code and
expose the deepest idle state through flags.
Since the device tree is probed by the cpuidle driver as well, move
the parameters required to discover the idle states into an appropriate
common place to both the driver and the powernv core code.
Another point is that fastsleep idle state may require workarounds in
the kernel to function properly. This workaround is introduced in the
subsequent patches. However neither the cpuidle driver or the hotplug
path need be bothered about this workaround.
They will be taken care of by the core powernv code.
Originally-by: Srivatsa S. Bhat <srivatsa@mit.edu>
Signed-off-by: Preeti U. Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Reviewed-by: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: linux-pm@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The patch implements the OPAL rtc driver that binds with the rtc
driver subsystem. The driver uses the platform device infrastructure
to probe the rtc device and register it to rtc class framework. The
'wakeup' is supported depending upon the property 'has-tpo' present
in the OF node. It provides a way to load the generic rtc driver in
in the absence of an OPAL driver.
The patch also moves the existing OPAL rtc get/set time interfaces to the
new driver and exposes the necessary OPAL calls using EXPORT_SYMBOL_GPL.
Test results:
-------------
Host:
[root@tul169p1 ~]# ls -l /sys/class/rtc/
total 0
lrwxrwxrwx 1 root root 0 Oct 14 03:07 rtc0 -> ../../devices/opal-rtc/rtc/rtc0
[root@tul169p1 ~]# cat /sys/devices/opal-rtc/rtc/rtc0/time
08:10:07
[root@tul169p1 ~]# echo `date '+%s' -d '+ 2 minutes'` > /sys/class/rtc/rtc0/wakealarm
[root@tul169p1 ~]# cat /sys/class/rtc/rtc0/wakealarm
1413274345
[root@tul169p1 ~]#
FSP:
$ smgr mfgState
standby
$ rtim timeofday
System time is valid: 2014/10/14 08:12:04.225115
$ smgr mfgState
ipling
$
CC: devicetree@vger.kernel.org
CC: tglx@linutronix.de
CC: rtc-linux@googlegroups.com
CC: a.zummo@towertech.it
Signed-off-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The generic Linux framework to power off the machine is a function pointer
called pm_power_off. The trick about this pointer is that device drivers can
potentially implement it rather than board files.
Today on powerpc we set pm_power_off to invoke our generic full machine power
off logic which then calls ppc_md.power_off to invoke machine specific power
off.
However, when we want to add a power off GPIO via the "gpio-poweroff" driver,
this card house falls apart. That driver only registers itself if pm_power_off
is NULL to ensure it doesn't override board specific logic. However, since we
always set pm_power_off to the generic power off logic (which will just not
power off the machine if no ppc_md.power_off call is implemented), we can't
implement power off via the generic GPIO power off driver.
To fix this up, let's get rid of the ppc_md.power_off logic and just always use
pm_power_off as was intended. Then individual drivers such as the GPIO power off
driver can implement power off logic via that function pointer.
With this patch set applied and a few patches on top of QEMU that implement a
power off GPIO on the virt e500 machine, I can successfully turn off my virtual
machine after halt.
Signed-off-by: Alexander Graf <agraf@suse.de>
[mpe: Squash into one patch and update changelog based on cover letter]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The dma_get_required_mask() function is used by some drivers to
query the platform about what DMA mask is needed to cover all of
memory. This is a bit of a strange semantic when we have to choose
between IOMMU translation or bypass, but essentially what it means
is "what DMA mask will give best performances".
Currently, our IOMMU backend always returns a 32-bit mask here, we
don't do anything special to it when we have bypass available. This
causes some drivers to choose a 32-bit mask, thus losing the ability
to use the bypass window, thinking this is more efficient. The problem
was reported from the driver of following device:
0004:03:00.0 0107: 1000:0087 (rev 05)
0004:03:00.0 Serial Attached SCSI controller: LSI Logic / Symbios \
Logic SAS2308 PCI-Express Fusion-MPT SAS-2 (rev 05)
This patch adds an override of that function in order to, instead,
return a 64-bit mask whenever a bypass window is available in order
for drivers to prefer this configuration.
Reported-by: Murali N. Iyer <mniyer@us.ibm.com>
Suggested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Handle Hypervisor Maintenance Interrupt (HMI) in Linux. This patch implements
basic infrastructure to handle HMI in Linux host. The design is to invoke
opal handle hmi in real mode for recovery and set irq_pending when we hit HMI.
During check_irq_replay pull opal hmi event and print hmi info on console.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We've already dropped the default pseries timeout to 10s, do
the same for powernv.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Build throws following errors when CONFIG_SMP=n
arch/powerpc/platforms/powernv/setup.c: In function ‘pnv_kexec_wait_secondaries_down’:
arch/powerpc/platforms/powernv/setup.c:179:4: error: implicit declaration of function ‘get_hard_smp_processor_id’
rc = opal_query_cpu_status(get_hard_smp_processor_id(i),
The usage of get_hard_smp_processor_id() needs the declaration from
<asm/smp.h>. The file setup.c includes <linux/sched.h>, which in-turn
includes <linux/smp.h>. However, <linux/smp.h> includes <asm/smp.h>
only on SMP configs and hence UP builds fail.
Fix this by directly including <asm/smp.h> in setup.c unconditionally.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc sets a low SECTION_SIZE_BITS to accomodate small pseries
boxes. We default to 16MB memory blocks, and boxes with a lot
of memory end up with enormous numbers of sysfs memory nodes.
Set a more reasonable default for powernv of 256MB.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Implement a method named pnv_get_proc_freq(unsigned int cpu) which
returns the current clock rate on the 'cpu' in Hz to be reported in
/proc/cpuinfo. This method uses the value reported by cpufreq when
such a value is sane. Otherwise it falls back to old way of reporting
the clockrate, i.e. ppc_proc_freq.
Set the ppc_md.get_proc_freq() hook to pnv_get_proc_freq() on the
PowerNV platform.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Firmware update on PowerNV platform takes several minutes. During
this time one CPU is stuck in FW and the kernel complains about "soft
lockups".
This patch returns all secondary CPUs to firmware before starting
firmware update process.
[ Reworked a bit and cleaned up -- BenH ]
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have a subtle race when sending CPUs back to OPAL on kexec.
We mark them as "in real mode" right before we send them down. Once
we've booted the new kernel, it might try to call opal_reinit_cpus()
to change endianness, and that requires all CPUs to be spinning inside
OPAL.
However there is no synchronization here and we've observed cases
where the returning CPUs hadn't established their new state inside
OPAL before opal_reinit_cpus() is called, causing it to fail.
The proper fix is to actually wait for them to go down all the way
from the kexec'ing kernel.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull main powerpc updates from Ben Herrenschmidt:
"This time around, the powerpc merges are going to be a little bit more
complicated than usual.
This is the main pull request with most of the work for this merge
window. I will describe it a bit more further down.
There is some additional cpuidle driver work, however I haven't
included it in this tree as it depends on some work in tip/timer-core
which Thomas accidentally forgot to put in a topic branch. Since I
didn't want to carry all of that tip timer stuff in powerpc -next, I
setup a separate branch on top of Thomas tree with just that cpuidle
driver in it, and Stephen has been carrying that in next separately
for a while now. I'll send a separate pull request for it.
Additionally, two new pieces in this tree add users for a sysfs API
that Tejun and Greg have been deprecating in drivers-core-next.
Thankfully Greg reverted the patch that removes the old API so this
merge can happen cleanly, but once merged, I will send a patch
adjusting our new code to the new API so that Greg can send you the
removal patch.
Now as for the content of this branch, we have a lot of perf work for
power8 new counters including support for our new "nest" counters
(also called 24x7) under pHyp (not natively yet).
We have new functionality when running under the OPAL firmware
(non-virtualized or KVM host), such as access to the firmware error
logs and service processor dumps, system parameters and sensors, along
with a hwmon driver for the latter.
There's also a bunch of bug fixes accross the board, some LE fixes,
and a nice set of selftests for validating our various types of copy
loops.
On the Freescale side, we see mostly new chip/board revisions, some
clock updates, better support for machine checks and debug exceptions,
etc..."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (70 commits)
powerpc/book3s: Fix CFAR clobbering issue in machine check handler.
powerpc/compat: 32-bit little endian machine name is ppcle, not ppc
powerpc/le: Big endian arguments for ppc_rtas()
powerpc: Use default set of netfilter modules (CONFIG_NETFILTER_ADVANCED=n)
powerpc/defconfigs: Enable THP in pseries defconfig
powerpc/mm: Make sure a local_irq_disable prevent a parallel THP split
powerpc: Rate-limit users spamming kernel log buffer
powerpc/perf: Fix handling of L3 events with bank == 1
powerpc/perf/hv_{gpci, 24x7}: Add documentation of device attributes
powerpc/perf: Add kconfig option for hypervisor provided counters
powerpc/perf: Add support for the hv 24x7 interface
powerpc/perf: Add support for the hv gpci (get performance counter info) interface
powerpc/perf: Add macros for defining event fields & formats
powerpc/perf: Add a shared interface to get gpci version and capabilities
powerpc/perf: Add 24x7 interface headers
powerpc/perf: Add hv_gpci interface header
powerpc: Add hvcalls for 24x7 and gpci (Get Performance Counter Info)
sysfs: create bin_attributes under the requested group
powerpc/perf: Enable BHRB access for EBB events
powerpc/perf: Add BHRB constraint and IFM MMCRA handling for EBB
...
Detect and recover from machine check when inside opal on a special
scom load instructions. On specific SCOM read via MMIO we may get a machine
check exception with SRR0 pointing inside opal. To recover from MC
in this scenario, get a recovery instruction address and return to it from
MC.
OPAL will export the machine check recoverable ranges through
device tree node mcheck-recoverable-ranges under ibm,opal:
# hexdump /proc/device-tree/ibm,opal/mcheck-recoverable-ranges
0000000 0000 0000 3000 2804 0000 000c 0000 0000
0000010 3000 2814 0000 0000 3000 27f0 0000 000c
0000020 0000 0000 3000 2814 xxxx xxxx xxxx xxxx
0000030 llll llll yyyy yyyy yyyy yyyy
...
...
#
where:
xxxx xxxx xxxx xxxx = Starting instruction address
llll llll = Length of the address range.
yyyy yyyy yyyy yyyy = recovery address
Each recoverable address range entry is (start address, len,
recovery address), 2 cells each for start and recovery address, 1 cell for
len, totalling 5 cells per entry. During kernel boot time, build up the
recovery table with the list of recovery ranges from device-tree node which
will be used during machine check exception to recover from MMIO SCOM UE.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The core idle loop now takes care of it. We need to add the runlatch
function calls to the idle routines which was earlier taken care of by
the arch specific idle routine.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Reviewed-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-pm@vger.kernel.org
Cc: linaro-kernel@lists.linaro.org
Link: http://lkml.kernel.org/n/tip-nr4mtbkkzf2oomaj85m24o7c@git.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
