Current ak4642 was not able to select pll.
This patch add support it.
It still expect PLL base input pin is MCKI.
see Table 5 "setting of PLL Mode" of datasheet
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This also adds the first DAI operation for AIF3 so fill out the ID and
the ops for that too.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Don't force enable the microphone bias on WM8903 when doing jack
detection, and don't force enable microphone bias. This allows
platforms to only enable microphone detection when a jack has been
inserted.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
If no report is specified then disable detection. Note that we don't
disable the slow clock, though the power consumption from it should
be negligable. That should be reference counted, ideally through DAPM.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allow machines to control exactly when the bias is turned on and off.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Some systems, such as those with mechanical jack detection, may wish
to force enable a pin (typically mic bias) only some of the time.
Support such systems by having disable_pin() also coveer force enabled
pins.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Some systems provide both mechanical and electrical detection of jack
status changes. On such systems power savings can be achieved by only
enabling the electrical detection methods when physical insertion has
been detected.
Begin supporting such systems by providing a notifier for jack status
changes which can be used to trigger any reconfiguration.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Gain controls on outputs affect the power consumption
when the gain is set to non 0 value.
Outputs with amps have one register to configure the
routing and the gain:
PREDL_CTL (0x25):
bit 0: Voice enable
bit 1: Audio L1 enable
bit 2: Audio L2 enable
bit 3: Audio R2 enable
bit 4-5: Gain (0x0 - power down, 0x1 - 6dB, 0x2 - 0dB, 0x3 - -6dB)
bit 0 - 3: is handled in DAPM domain (DAPM_MIXER)
bit 4 - 5: has simple volume control
If there is no audio activity (BIAS_STANDBY), and
user changes the volume, than the output amplifier will
be enabled.
If the user changes the routing (but the codec remains in
BIAS_STANDBY), than the cached gain value also be written
to the register, which enables the amplifier.
The existing workaround for this is to have virtual
PGAs associated with the outputs, and whit DAPM PMD
the gain on the output will be forced to 0 (off) by
bypassing the regcache.
This failed to disable the amplifiers in several
scenario (as mentioned above).
Also if the codec is in BIAS_ON state, and user modifies
a volume control, which path is actually not enabled, than
that amplifier will be enabled as well, but it will
be not turned off, since there is no DAPM path, which
would make mute it.
To prevent amps being enabled, when they are not
needed, introduce the following workaround:
Track the state of each of this type of output.
In twl4030_write only allow actual write, when the
given output is enabled, otherwise only update
the reg_cache.
The PGA event handlers on power up will write the cached
value to the chip (restoring gain, routing selection).
On power down 0 is written to the register (disabling
the amp, and also just in case clearing the routing).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
serial: sh-sci: remove duplicated #include
sh: Export uncached helper symbols.
sh: Fix up NUMA build for 29-bit.
serial: sh-sci: Fix build failure for non-sh architectures.
sh: Fix up uncached offset for legacy 29-bit mode.
sh: Support CPU affinity masks for INTC controllers.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6:
alpha: fix compile errors in dma-mapping-common.h
alpha: remove trailing spaces in messages
alpha: use __ratelimit
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Remove IOMMU_VMERGE config option
powerpc: Fix swiotlb to respect the boot option
powerpc: Do not call prink when CONFIG_PRINTK is not defined
powerpc: Use correct ccr bit for syscall error status
powerpc/fsl-booke: Get coherent bit from PTE
powerpc/85xx: Make sure lwarx hint isn't set on ppc32
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty_port,usb-console: Fix usb serial console open/close regression
tty: cpm_uart: use resource_size()
tty_buffer: Fix distinct type warning
hvc_console: Fix race between hvc_close and hvc_remove
uartlite: Fix build on sparc.
tty: Take a 256 byte padding into account when buffering below sub-page units
Revert "tty: Add a new VT mode which is like VT_PROCESS but doesn't require a VT_RELDISP ioctl call"
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
driver core: numa: fix BUILD_BUG_ON for node_read_distance
driver-core: document ERR_PTR() return values
kobject: documentation: Update to refer to kset-example.c.
sysdev: the cpu probe/release attributes should be sysdev_class_attributes
kobject: documentation: Fix erroneous example in kobject doc.
driver-core: fix missing kernel-doc in firmware_class
Driver core: Early platform kernel-doc update
sysfs: fix sysfs lockdep warning in mlx4 code
sysfs: fix sysfs lockdep warning in infiniband code
sysfs: fix sysfs lockdep warning in ipmi code
sysfs: Initialised pci bus legacy_mem field before use
sysfs: use sysfs_bin_attr_init in firmware class driver
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (45 commits)
USB: gadget/multi: cdc_do_config: remove redundant check
usb: r8a66597-hcd: fix removed from an attached hub
USB: xhci: Make endpoint interval debugging clearer.
USB: Fix usb_fill_int_urb for SuperSpeed devices
USB: cp210x: Remove double usb_control_msg from cp210x_set_config
USB: Remove last bit of CONFIG_USB_BERRY_CHARGE
USB: gadget: add gadget controller number for s3c-hsotg driver
USB: ftdi_sio: Fix locking for change_speed() function
USB: g_mass_storage: fixed module name in Kconfig
USB: gadget: f_mass_storage::fsg_bind(): fix error handling
USB: g_mass_storage: fix section mismatch warnings
USB: gadget: fix Blackfin builds after gadget cleansing
USB: goku_udc: remove potential null dereference
USB: option.c: Add Pirelli VID/PID and indicate Pirelli's modem interface is 0xff
USB: serial: Fix module name typo for qcaux Kconfig entry.
usb: cdc-wdm: Fix deadlock between write and resume
usb: cdc-wdm: Fix order in disconnect and fix locking
usb: cdc-wdm:Fix loss of data due to autosuspend
usb: cdc-wdm: Fix submission of URB after suspension
usb: cdc-wdm: Fix race between disconnect and debug messages
...
If instantiation of a card failed, we still have to remove it from the
card list on unregistration. This fixes an Oops on Migo-R, triggering,
when after a failed firmware load attempt the driver modules are removed
and re-inserted again.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This fixes a memory corruption when ASoC devices are used in
full-duplex mode. Specifically for pxa-ssp code, where this pointer
is dynamically allocated for each direction and destroyed upon each
stream start.
All other platforms are fixed blindly, I couldn't even compile-test
them. Sorry for any breakage I may have caused.
Reported-by: Sven Neumann <s.neumann@raumfeld.com>
Reported-by: Michael Hirsch <m.hirsch@raumfeld.com>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (205 commits)
ceph: update for write_inode API change
ceph: reset osd after relevant messages timed out
ceph: fix flush_dirty_caps race with caps migration
ceph: include migrating caps in issued set
ceph: fix osdmap decoding when pools include (removed) snaps
ceph: return EBADF if waiting for caps on closed file
ceph: set osd request message front length correctly
ceph: reset front len on return to msgpool; BUG on mismatched front iov
ceph: fix snaptrace decoding on cap migration between mds
ceph: use single osd op reply msg
ceph: reset bits on connection close
ceph: remove bogus mds forward warning
ceph: remove fragile __map_osds optimization
ceph: fix connection fault STANDBY check
ceph: invalidate_authorizer without con->mutex held
ceph: don't clobber write return value when using O_SYNC
ceph: fix client_request_forward decoding
ceph: drop messages on unregistered mds sessions; cleanup
ceph: fix comments, locking in destroy_inode
ceph: move dereference after NULL test
...
Fix trivial conflicts in Documentation/ioctl/ioctl-number.txt
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: trivial white space
[CIFS] checkpatch cleanup
cifs: add cifs_revalidate_file
cifs: add a CIFSSMBUnixQFileInfo function
cifs: add a CIFSSMBQFileInfo function
cifs: overhaul cifs_revalidate and rename to cifs_revalidate_dentry
This fixes a warning ("pxa_free_dma: trying to free channel 0 which is
already freed") when a device was opened but the hw_params() call
failed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
cdc_do_config() had a double ret check after fsg_add().
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
fix the problem that when a USB hub is attached to the r8a66597-hcd and
a device is removed from that hub, it's likely that a kernel panic follows.
Reported-by: Markus Pietrek <Markus.Pietrek@emtrion.de>
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The xHCI hardware can only handle polling intervals that are a power of
two. When we add a new endpoint during a bandwidth allocation, and the
polling interval is rounded down to a power of two, print the original
polling interval in the endpoint descriptor.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB 3 and Wireless USB specify a logarithmic encoding of the endpoint
interval that matches the USB 2 specification. usb_fill_int_urb() didn't
know that and was filling in the interval as if it was USB 1.1. Fix
usb_fill_int_urb() for SuperSpeed devices, but leave the wireless case
alone, because David Vrabel wants to keep the old encoding.
Update the struct urb kernel doc to note that SuperSpeed URBs must have
urb->interval specified in microframes.
Add a missing break statement in the usb_submit_urb() interrupt URB
checking, since wireless USB and SuperSpeed USB encode urb->interval
differently. This allows xHCI roothubs to actually register with khubd.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes a double usb_control_msg that sets the cp210x
configuration registers a second time when calling cp210x_set_config.
For data sizes >2 the second write gets corrupted.
The patch has been created against 2.6.34-rc1, but all cp210x driver
revisions are affected.
Signed-off-by: Michael Brunner <mibru@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
One last bit was missed while removing the USB_BERRY_CHARGE config
option in a8d4211f33 which gets dropped
by this patch.
Signed-off-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This prevents some drivers from complaining that no bcdDevice id was set.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The change_speed() function should be serialized against multiple calls.
Use the cfg_lock mutex to do this.
Signed-off-by: Alessio Igor Bogani <abogani@texware.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Kconfig help message for Mass Storage Gadget claimed the
module will be named "g_file_storage" whereas it should be
"g_mass_storage".
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Contrary to the comment in fsg_add, fsg_bind calls fsg_unbind on errors,
which decreases refcount and frees the fsg_dev structure, causing trouble
when fsg_add does the same.
Fix it by simply leaving up cleanup to fsg_add().
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The recent commit (0e530b4578) that moved usb_ep_autoconfig from the
__devinit section to the __init section missed the mass storage device.
Its fsg_bind() function uses the usb_ep_autoconfig() function from non
__init context leading to:
WARNING: drivers/usb/gadget/g_mass_storage.o(.text): Section mismatch in
reference from the function _fsg_bind()
to the function .init.text:_usb_ep_autoconfig()
So move fsg_bind() into __init as well.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The recent change to clean out dead gadget drivers (90f7976880)
missed the call to gadget_is_musbhsfc() behind CONFIG_BLACKFIN. This
causes Blackfin gadget builds to fail since the function no longer
exists anywhere.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
"dev" is always null here. In the end it's only used to get the
pci_name() of "pdev" which is redundant information and so I
removed it.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The module is called qcaux and not moto_modem. Also use help instead of
---help-- to be in sync with the other Kconfig entries.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The new runtime PM scheme allows resume() to have no locks.
This fixes the deadlock.
Signed-off-by: Oliver Neukum <neukum@b1-systems.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- as the callback can schedule work, URBs must be killed first
- if the driver causes an autoresume, the caller must handle locking
Signed-off-by: Oliver Neukum <neukum@b1-systems.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The guarding flag must be set and tested under spinlock
and cleared before the URBs are resubmitted in resume.
Signed-off-by: Oliver Neukum <neukum@b1-systems.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
