The return value of iovar set function should be saved and checked.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Configure ipv6 address for neighbor discovery offload ip table in
firmware obtained through ipv6 address notification callback.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add additional length checks on firmware events to create more
robust code.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Lei Zhang <leizh@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Country code configuration in a device is a device specific
operation. For this the country code as specified by reg notifier
(iso3166 alpha2) needs to be translated to a device specific
country locale and revision number. This patch adds this
translation and puts a placeholder in the device specific settings
where the translation table can be stored. Additional patches will
be needed to read these tables from for example device platform
data.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In some cases wiphy->wowlan could be NULL if firmware doesn't have the
support. Driver should check for support before walking down the feature
flags.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some systems have problems with allocating memory allocation larger
then 64K. Often on unload/load or suspend/resume a failure is
reported: Could not allocate wiphy device. This patch makes the
escan intermediate storage buf dynamically allocated, and smaller
than 64K.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Dropping the '_timeout' from the function name as the fact that a timeout
value is passed makes it obvious a timeout is used. Also helps to keep code
lines a bit shorter and easier to stick to 80 char boundary.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Routine rtl_addr_delay() uses delay statements in code that can
sleep. To improve system responsiveness, the various delay statements
are changed.
In addition, routines rtl_rfreg_delay() and rtl_bb_delay() are
rewritten to use the code in rtl_addr_delay() for most of their
input values.
Suggested-by: Byeoungwook Kim <quddnr145@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Import new headers from my firmware branch:
<https://github.com/chunkeey/carl9170fw>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The buffer needs to be zero terminated in case the user data is not.
Otherwise we run off the end of the buffer.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When driver rtl8821ae is loaded but not connected to any AP, it logs
a "firmware not ready to run" message roughly once a minute. To
eliminate logging this massage under normal debug conditions, the
degug level needed to print this message is increased.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath.git patches for 4.6. Major changes:
ath10k
* dt: add bindings for ipq4019 wifi block
* start adding support for qca4019 chip
ath9k
* add device ID for Toshiba WLM-20U2/GN-1080
* allow more than one interface on DFS channels
Zhang Shengju says:
====================
use reset to set header pointers
This patch series replace set function with reset when offset is zero.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since offset is zero, it's not necessary to use set function. Reset
function is straightforward, and will remove the unnecessary add
operation in set function.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since offset is zero, it's not necessary to use set function. Reset
function is straightforward, and will remove the unnecessary add
operation in set function.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since offset is zero, it's not necessary to use set function. Reset
function is straightforward, and will remove the unnecessary add
operation in set function.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since offset is zero, it's not necessary to use set function. Reset
function is straightforward, and will remove the unnecessary add operation
in set function.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9CQy
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-rewrite-20160304' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
RxRPC: Rewrite part 1
Here's the first set of patches from my RxRPC rewrite, aimed at net-next.
These do some clean ups and bug fixes. Most of the changes are small, but
there are a couple of bigger changes:
(*) Convert call flag numbers and event numbers into enums. Then rename
the event numbers to all have _EV_ in their name to stop confusion.
Fix one instance of an event bit being used instead of a flag bit.
(*) A copy of the Rx protocol header is kept in the sk_buff private data.
Keep this in host byte order rather than network byte order as it
makes more sense. A number of other fields then get converted into
host byte order too.
Conversion between host and network byte order is then done at the
packet reception/generation stage.
This is based on net-next/master
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel says:
====================
uapi: consolidate DIV_ROUND_UP definition
The inital goal was to consolidate ethtool.h uapi header. But I took the
opportunity to remove all duplicate definitions of DIV_ROUND_UP.
v3: add patch #2 and #3
v2: split the patch
define DIV_ROUND_UP in uapi
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
INT_MAX needs limits.h in userland.
When ethtool.h is included by a userland app, we got the following error:
.../usr/include/linux/ethtool.h: In function 'ethtool_validate_speed':
.../usr/include/linux/ethtool.h:1471:18: error: 'INT_MAX' undeclared (first use in this function)
return speed <= INT_MAX || speed == SPEED_UNKNOWN
^
Fixes: e02564ee33 ("ethtool: make validate_speed accept all speeds between 0 and INT_MAX")
CC: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let's use __KERNEL_DIV_ROUND_UP, which is defined in uapi/linux/kernel.h.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
let's use the common definition to avoid the following warning during the
compilation:
drivers/scsi/cxgbi/cxgb4i/cxgb4i.c:161:0: warning: "DIV_ROUND_UP" redefined
#define DIV_ROUND_UP(n, d) (((n) + (d) - 1) / (d))
^
In file included from include/linux/list.h:8:0,
from include/linux/module.h:9,
from drivers/scsi/cxgbi/cxgb4i/cxgb4i.c:16:
include/linux/kernel.h:67:0: note: this is the location of the previous definition
#define DIV_ROUND_UP __KERNEL_DIV_ROUND_UP
^
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DIV_ROUND_UP is defined in linux/kernel.h only for the kernel.
When ethtool.h is included by a userland app, we got the following error:
include/linux/ethtool.h:1218:8: error: variably modified 'queue_mask' at file scope
__u32 queue_mask[DIV_ROUND_UP(MAX_NUM_QUEUE, 32)];
^
Let's add a common definition in uapi and use it everywhere.
Fixes: ac2c7ad0e5 ("net/ethtool: introduce a new ioctl for per queue setting")
CC: Kan Liang <kan.liang@intel.com>
Suggested-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rolf is no longer in his previous role at Netronome and as far as I know no
longer working on the NFP driver. Thus it does not seem appropriate for him
to be a co-maintainer anymore.
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the ICMP message processing code, don't try to map ICMP codes to UNIX
error codes as the caller (IPv4/IPv6) already did that for us (ee_errno).
Signed-off-by: David Howells <dhowells@redhat.com>
The version number rxkad places in the response should be network byte
order.
Whilst we're at it, rearrange the code to be more readable.
Signed-off-by: David Howells <dhowells@redhat.com>
Use ACCESS_ONCE() when accessing the other-end pointer into a circular
buffer as it's possible the other-end pointer might change whilst we're
doing this, and if we access it twice, we might get some weird things
happening.
Signed-off-by: David Howells <dhowells@redhat.com>
Currently, received RxRPC packets outside the range 1-13 are rejected.
There are, however, holes in the range that should also be rejected - plus
at least one type we don't yet support - so reject these also.
Signed-off-by: David Howells <dhowells@redhat.com>
The upper bound of the defined range for rx_mtu is being set in the same
member as the lower bound (extra1) rather than the correct place (extra2).
I'm not entirely sure why this compiles.
Signed-off-by: David Howells <dhowells@redhat.com>
Currently, a copy of the Rx packet header is copied into the the sk_buff
private data so that we can advance the pointer into the buffer,
potentially discarding the original. At the moment, this copy is held in
network byte order, but this means we're doing a lot of unnecessary
translations.
The reasons it was done this way are that we need the values in network
byte order occasionally and we can use the copy, slightly modified, as part
of an iov array when sending an ack or an abort packet.
However, it seems more reasonable on review that it would be better kept in
host byte order and that we make up a new header when we want to send
another packet.
To this end, rename the original header struct to rxrpc_wire_header (with
BE fields) and institute a variant called rxrpc_host_header that has host
order fields. Change the struct in the sk_buff private data into an
rxrpc_host_header and translate the values when filling it in.
This further allows us to keep values kept in various structures in host
byte order rather than network byte order and allows removal of some fields
that are byteswapped duplicates.
Signed-off-by: David Howells <dhowells@redhat.com>
Convert call flag and event numbers into enums and move their definitions
outside of the struct.
Also move the call state enum outside of the struct and add an extra
element to count the number of states.
Signed-off-by: David Howells <dhowells@redhat.com>
Fix a case where RXRPC_CALL_RELEASE (an event) is being used to specify a
flag bit. RXRPC_CALL_RELEASED should be used instead.
Signed-off-by: David Howells <dhowells@redhat.com>
Some devices declare a high number of TX queues, then set a much
lower real_num_tx_queues
This cause setups using fq_codel, sfq or fq as the default qdisc to consume
more memory than really needed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew and Ying Huang's test robot both reported usage count problems that
trace back to the 'keep address on ifdown' patch.
>From Andrew:
We execute CRIU test on linux-next. On the current linux-next kernel
they hangs on creating a network namespace.
The kernel log contains many massages like this:
[ 1036.122108] unregister_netdevice: waiting for lo to become free.
Usage count = 2
[ 1046.165156] unregister_netdevice: waiting for lo to become free.
Usage count = 2
[ 1056.210287] unregister_netdevice: waiting for lo to become free.
Usage count = 2
I tried to revert this patch and the bug disappeared.
Here is a set of commands to reproduce this bug:
[root@linux-next-test linux-next]# uname -a
Linux linux-next-test 4.5.0-rc6-next-20160301+ #3 SMP Wed Mar 2
17:32:18 UTC 2016 x86_64 x86_64 x86_64 GNU/Linux
[root@linux-next-test ~]# unshare -n
[root@linux-next-test ~]# ip link set up dev lo
[root@linux-next-test ~]# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
group default qlen 1
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
[root@linux-next-test ~]# logout
[root@linux-next-test ~]# unshare -n
-----
The problem is a change made to RTM_DELADDR case in __ipv6_ifa_notify that
was added in an early version of the offending patch and is no longer
needed.
Fixes: f1705ec197 ("net: ipv6: Make address flushing on ifdown optional")
Cc: Andrey Wagin <avagin@gmail.com>
Cc: Ying Huang <ying.huang@linux.intel.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since ezchip network driver is written with big endian EZChip platform it
is necessary to add support for little endian architecture.
The first issue is that the order of the bits in a bit field is
implementation specific. So all the bit fields are removed.
Named constants are used to access necessary fields.
And the second one is that network byte order is big endian.
For example, data on ethernet is transmitted with most-significant
octet (byte) first. So in case of little endian architecture
it is important to swap data byte order when we read it from
register. In case of unaligned access we can use "get_unaligned_be32"
and in other case we can use function "ioread32_rep" which reads all
data from register and works either with little endian or big endian
architecture.
And then when we are going to write data to register we need to restore
byte order using the function "put_unaligned_be32" in case of
unaligned access and in other case "iowrite32_rep".
The last little fix is a space between type and pointer to observe
coding style.
Signed-off-by: Lada Trimasova <ltrimas@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Noam Camus <noamc@ezchip.com>
Cc: Tal Zilcer <talz@ezchip.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new NET_DEVLINK infrastructure can be a loadable module, but the drivers
using it might be built-in, which causes link errors like:
drivers/net/built-in.o: In function `mlx4_load_one':
:(.text+0x2fbfda): undefined reference to `devlink_port_register'
:(.text+0x2fc084): undefined reference to `devlink_port_unregister'
drivers/net/built-in.o: In function `mlxsw_sx_port_remove':
:(.text+0x33a03a): undefined reference to `devlink_port_type_clear'
:(.text+0x33a04e): undefined reference to `devlink_port_unregister'
There are multiple ways to avoid this:
a) add 'depends on NET_DEVLINK || !NET_DEVLINK' dependencies
for each user
b) use 'select NET_DEVLINK' from each driver that uses it
and hide the symbol in Kconfig.
c) make NET_DEVLINK a 'bool' option so we don't have to
list it as a dependency, and rely on the APIs to be
stubbed out when it is disabled
d) use IS_REACHABLE() rather than IS_ENABLED() to check for
NET_DEVLINK in include/net/devlink.h
This implements a variation of approach a) by adding an
intermediate symbol that drivers can depend on, and changes
the three drivers using it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 09d4d087cd ("mlx4: Implement devlink interface")
Fixes: c4745500e9 ("mlxsw: Implement devlink interface")
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2016-03-01
Here's our main set of Bluetooth & 802.15.4 patches for the 4.6 kernel.
- New Bluetooth HCI driver for Intel/AG6xx controllers
- New Broadcom ACPI IDs
- LED trigger support for indicating Bluetooth powered state
- Various fixes in mac802154, 6lowpan and related drivers
- New USB IDs for AR3012 Bluetooth controllers
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
I added this check in setup_tc to multiple drivers,
if (handle != TC_H_ROOT || tc->type != TC_SETUP_MQPRIO)
Unfortunately restricting to TC_H_ROOT like this breaks the old
instantiation of mqprio to setup a hardware qdisc. This patch
relaxes the test to only check the type to make it equivalent
to the check before I broke it. With this the old instantiation
continues to work.
A good smoke test is to setup mqprio with,
# tc qdisc add dev eth4 root mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 \
queues 0@0 1@1 2@2 3@3 4@4 5@5 6@6 7@7
Fixes: e4c6734eaa ("net: rework ndo tc op to consume additional qdisc handle paramete")
Reported-by: Singh Krishneil <krishneil.k.singh@intel.com>
Reported-by: Jake Keller <jacob.e.keller@intel.com>
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: Or Gerlitz <ogerlitz@mellanox.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
JP WiFi certification for bandwidth of channel 14 failed, the OBW
is lower than the requirement. Clear the bb filter calibration power
threshold to increase OBW(+2). The fix only for qca9531 chip now.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In some configurations, this function uses more than the warning limit
of 1024 bytes:
drivers/net/wireless/ath/ath9k/ar9003_aic.c: In function 'ar9003_aic_cal_post_process':
drivers/net/wireless/ath/ath9k/ar9003_aic.c:434:1: error: the frame size of 1040 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
It turns out that there are two large arrays on the stack here, but
almost all the data in them is never used outside of the loop in
which it gets written, so we can replace the array with a single
instance.
The .valid flag is used later, so I'm replacing the array of structures
with an array of bools. An obvious follow-up optimization would be
to replace it with a bitmask and set_bit()/find_first_bit()/
find_last_bit()/... operations. However, I have not tested this patch,
so I sticked to the simpler transformation that does the job of
reducing the stack usage to a harmless level.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make NF load complete quickly and reliably. NF load execution
is delayed by HW to end of frame if frame Rx or Tx is ongoing.
Increasing timeout to max frame duration. If NF cal is ongoing
before NF load, stop it before load, and restart it afterwards.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
First check for the device state before enabling / disabling
btcoex, also return a proper error value. Enabling / disabling
btcoex ideally does a f/w + ath10k_core_restart so the checks
that are applicable for 'simulate_fw_crash' shall be applicable
for this as well
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To enable per peer stats feature we are reducing the number of peers.
Firmware has introduced tx stats feature. We have memory limitation in
firmware to add these additional bytes.
These are the new variables introduced in the firmware.
======== =======================
Variable Bytes required/per rate
======== =======================
TX success packets 1
TX failed packets 1
Retry packets 1
Success bytes 2
TX failed bytes 2
Retry bytes 2
Tx duration 4
Rate 1
Bw and AMPDU flags 1
Total 16 (because of allocation in word pattern)
Firmware sends these tx_stats in pktlog.
If we consider 4 feedbacks at a time, Frimware need about ~1K memory for coding
and 8192 bytes required / per rate [ 4*16*128(peers)].
To accommodate this firmware needs to reduce 10 peers.
This fixes a firmware crash with firmware-5.bin_10.2.4.70.22-2.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
