All Colibri iMX7 SKUs use either single-die NAND or eMMC, hence
NAND_CE1 is not used on the module and can be used as a GPIO by
carrier boards.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use pull-ups instead of pull-downs for the pins which are already
pulled-up externally.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Colibri pins PWM<A> and <D> are multiplexed on the module, make
sure the secondary SoC pin is not active.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Colibri default which enables USB Host power is not necessarily
tied to the OTG2 controller, some carrier board use the pin to
control USB power for both controllers. Hence name the pinctrl
group more generic.
Also move the regulator to the generic eval-v3 device tree since
the regulator is always on the carrier board. In the Colibri iMX7S
case the regulator is just not used. This allows to reuse the
regulator in a upcoming SKU Colibri iMX7D 1GB with eMMC.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is preferred to use the panel compatible string rather than passing
the LCD timing in the device tree.
So pass the "sii,43wvf1g" compatible string which describes the parallel
LCD.
Also, pass the 'backlight' property as described in
Documentation/devicetree/bindings/display/panel/simple-panel.txt
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is not recommended to place regulators inside "simple-bus", so move
them out.
The motivation for doing this is to make it easier to adding new
regulators.
Signed-off-by: Marco Franchi <marcofrk@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is preferred to use the panel compatible string rather than passing
the LCD timing in the device tree.
So pass the "sii,43wvf1g" compatible string, which describes the parallel
LCD.
Also pass the 'backlight' property as described in
Documentation/devicetree/bindings/display/panel/simple-panel.txt
Signed-off-by: Marco Franchi <marcofrk@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
All Toradex Carrier Boards use a st,m41t0 compatible RTC. Compared
to a st,m41t00 this RTC has also an oscillator fail bit which allows
to detect when the RTC lost track of time.
Cc: Sanchayan Maity <maitysanchayan@gmail.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This avoids the warning
hw perfevents: no interrupt-affinity property for /pmu, guessing.
Signed-off-by: Esben Haabendal <eha@deif.com>
[RV: adapt commit log to the warning emitted in current mainline]
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The LS1021A can be reset via the dcfg regmap in the same way as the
arm64 layerscape SoCs, so add the corresponding DT node.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The USB PHYs are supplied via MC13892 VUSB regulator rail,
so properly describe this in the device tree.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
device_type = "pci" should be used for the SoC level PCI controller and
it is already present at imx6qdl.dtsi.
Remove it from the subnode in order to fix the following build
warnings with W=1:
arch/arm/boot/dts/imx6q-zii-rdu2.dtb: Warning (pci_bridge): Node /soc/pcie@1ffc000/pci@0 missing ranges for PCI bridge (or not a bridge)
arch/arm/boot/dts/imx6q-zii-rdu2.dtb: Warning (pci_bridge): Node /soc/pcie@1ffc000/pci@0 missing bus-range for PCI bridge
arch/arm/boot/dts/imx6q-zii-rdu2.dtb: Warning (unit_address_format): Failed prerequisite 'pci_bridge'
arch/arm/boot/dts/imx6q-zii-rdu2.dtb: Warning (pci_device_reg): Failed prerequisite 'pci_bridge'
arch/arm/boot/dts/imx6q-zii-rdu2.dtb: Warning (pci_device_bus_num): Failed prerequisite 'pci_bridge'
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is not recommended to place regulator nodes inside simple-bus, so
move them out in order to fix the following build warnings with W=1:
arch/arm/boot/dts/imx6ul-14x14-evk.dtb: Warning (simple_bus_reg): Node /regulators/sd1_regulator missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove the unneeded unit address for the i2cmux nodes in order to fix
the following build warnings with W=1:
arch/arm/boot/dts/imx6q-nitrogen6_max.dtb: Warning (unit_address_vs_reg): Node /i2cmux@2 has a unit name, but no reg property
arch/arm/boot/dts/imx6q-nitrogen6_max.dtb: Warning (unit_address_vs_reg): Node /i2cmux@3 has a unit name, but no reg property
While at it, rename the i2cmux nodes and subnodes to make it clearer to which
i2c controller the mux belongs to.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove the unneeded unit address for the port nodes in order to fix
the following build warnings with W=1:
arch/arm/boot/dts/imx6q-h100.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/i2c@21a0000/tc358743@f/port@0 has a unit name, but no reg property
arch/arm/boot/dts/imx6q-h100.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@0 has a unit name, but no reg property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As described in
Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
there is no 'reg' property under stmpe_touchscreen, so remove it
to fix the following build warning with W=1:
arch/arm/boot/dts/imx6dl-colibri-eval-v3.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/i2c@21a4000/stmpe811@41/stmpe_touchscreen has a reg or ranges property, but no unit name
Cc: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As described in
Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
there is no 'reg' property under stmpe_touchscreen, so remove it
to fix the following build warning with W=1:
arch/arm/boot/dts/imx6q-apalis-eval.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/i2c@21a4000/stmpe811@41/stmpe_touchscreen has a reg or ranges property, but no unit name
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move disp0 node from soc node to root node.
disp0 node does not have any register properties and thus
shouldn't be placed on the bus.
This fixes the following build warnings with W=1:
arch/arm/boot/dts/imx6dl-aristainetos_4.dtb: Warning (simple_bus_reg): Node /soc/disp0 missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is not recommended to place regulator nodes inside simple-bus, so
move them out in order to fix the following build warnings with W=1:
arch/arm/boot/dts/imx6dl-aristainetos_4.dtb: Warning (unit_address_vs_reg): Node /regulators/regulator@0 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-aristainetos_4.dtb: Warning (unit_address_vs_reg): Node /regulators/regulator@1 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-aristainetos_4.dtb: Warning (unit_address_vs_reg): Node /regulators/regulator@2 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-aristainetos_4.dtb: Warning (unit_address_vs_reg): Node /regulators/regulator@3 has a unit name, but no reg property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is not recommended to place regulator nodes inside simple-bus, so
move them out in order to fix the following build warnings with W=1:
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (simple_bus_reg): Node /regulators/3p3v missing or empty reg/ranges property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (simple_bus_reg): Node /regulators/usb-h1-vbus missing or empty reg/ranges property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (simple_bus_reg): Node /regulators/usb-otg-vbus missing or empty reg/ranges property
Cc: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move disp0 node from soc node to root node.
disp0 node does not have any register properties and thus
shouldn't be placed on the bus.
This fixes the following build warnings with W=1:
arch/arm/boot/dts/imx53-tx53-x03x.dtb: Warning (simple_bus_reg): Node /soc/disp0 missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As described in
Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
there is no 'reg' property under stmpe_touchscreen, so remove it
to fix the following build warning with W=1:
arch/arm/boot/dts/imx53-m53evk.dtb: Warning (unit_address_vs_reg): Node /soc/aips@60000000/i2c@63fc4000/stmpe610@41/stmpe_touchscreen has a reg or ranges property, but no unit name
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As described at Documentation/devicetree/bindings/mfd/mc13xxx.txt the
reg property is mandatory, so add the corresponding unit address in
order to fix the following build warnings with W=1:
arch/arm/boot/dts/imx51-zii-rdu1.dtb: Warning (unit_address_vs_reg): Node /soc/aips@70000000/spba@70000000/ecspi@70010000/pmic@0/leds/sysled0 has a reg or ranges property, but no unit name
arch/arm/boot/dts/imx51-zii-rdu1.dtb: Warning (unit_address_vs_reg): Node /soc/aips@70000000/spba@70000000/ecspi@70010000/pmic@0/leds/sysled1 has a reg or ranges property, but no unit name
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The syscon node has an incorrect notation for its unit address and the
wdt node has an unneeded unit address.
Fix them so that the following build warnings with W=1 are gone:
arch/arm/boot/dts/imx51-ts4800.dtb: Warning (unit_address_vs_reg): Node /soc/aips@80000000/weim@83fda000/fpga@0/syscon@b0010000/wdt@e has a unit name, but no reg property
arch/arm/boot/dts/imx51-ts4800.dtb: Warning (unit_address_vs_reg): Node /soc/aips@80000000/weim@83fda000/fpga@0/touchscreen has a reg or ranges property, but no unit name
arch/arm/boot/dts/imx51-ts4800.dtb: Warning (simple_bus_reg): Node /soc/aips@80000000/weim@83fda000/fpga@0/syscon@b0010000 simple-bus unit address format error, expected "10000"
arch/arm/boot/dts/imx51-ts4800.dtb: Warning (simple_bus_reg): Node /soc/aips@80000000/weim@83fda000/fpga@0/touchscreen simple-bus unit address format error, expected "12000"
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds support for the i.MX6 Quad variant of the Variscite DART-MX6
SoM Carrier-Board.
This Carrier-Board has the following :
- LVDS interface for the VLCD-CAP-GLD-LVDS 7" LCD 800 x 480 touch display
- HDMI Connector
- USB Host + USB OTG Connector
- 10/100/1000 Mbps Ethernet
- miniPCI-Express slot
- SD Card connector
- Audio Headphone/Line In jack connectors
- On-board DMIC
- CAN bus header
- SPI header
- Camera Interfaces header
- 4xButtons, 2xLeds
- OnBoard RTC with Coin Backup battery socket
- RS232 Header + USB-Serial debug port
Product Page : http://www.variscite.com/products/evaluation-kits/dart-mx6-kits
The board support is done with all on-board and header interfaces enabled.
7" LVDS Touchscreen is enabled by default along HDMI output.
Audio interface is supported with the "simple-card" bindings.
PCIe slot, On-Board DMIC and Camera Interfaces are not handled yet.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds support for the Variscite DART-MX6 SoM with :
- i.MX6 Quad or Dual Lite SoC
- 1Gb/2Gb LPDDR2
- 4-64 GB eMMC
- Camera Interface
- HDMI+CEC interface
- LVDS / DSI / Parallel RGB interfaces
- Ethernet RGMII interface
- On-SoM Wi-Fi/Bluetooth with WiLink wl1835 SDIO Module
- SD/MMC/SDIO interface
- USB Host + USB OTG interface
- I2C interfaces
- SPI interfaces
- PCI-Express 2.0 interface
- on-SoM Audio Codec with HP/Line-In interfaces + DMIC interface
- Digital Audio interface
- S/PDIF interface
Product website : http://www.variscite.com/products/system-on-module-som/cortex-a9/dart-mx6-cpu-freescale-imx6
Support is handled with a SoM-centric dtsi exporting the default interfaces
along the default pinmuxing to be enabled by the board dts file.
Only board-independent devices like WiFi, eMMC or PMIC are enabled in the dtsi.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add missing pinmux entry for OSC32K_32K_OUT on pad ENET_RXD0 used by the
Variscite DART-MX6 SoM.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
LS1021AQDS support NAND flash on IFC chip-select 2.
So add NAND node in device tree for IFC controller.
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Separate the old imx7d-pico into cpu (imx7d-pico.dtsi) and baseboard
(imx7d-pico-pi.dts) dts so the same cpu dtsi can be used in different
baseboards variants.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The correct unit address for interrupt-controller is 0x40003000, so
change it accordingly in order to fix the following build warning
with W=1:
arch/arm/boot/dts/vf500-colibri-eval-v3.dtb: Warning (simple_bus_reg): Node /soc/aips-bus@40000000/interrupt-controller@40002000 simple-bus unit address format error, expected "40003000"
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The correct unit address for spba-bus is 0x2240000, so change it
accordingly in order to fix the following build warning with W=1:
arch/arm/boot/dts/imx6sx-sabreauto.dtb: Warning (simple_bus_reg): Node /soc/aips-bus@2200000/spba-bus@2200000 simple-bus unit address format error, expected "2240000"
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move iio-hwmon node from soc node to root node.
iio-hwmon node does not have any register properties and thus
shouldn't be placed on the bus.
This fixes the following build warnings with W=1:
arch/arm/boot/dts/vf500-colibri-eval-v3.dtb: Warning (simple_bus_reg): Node /soc/iio-hwmon missing or empty reg/ranges property
Based on a patch from Simon Horman for the renesas r8a7795 dtsi.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add unit address and reg for the anatop nodes in order to fix the
following build warnings with W=1:
arch/arm/boot/dts/imx7d-cl-som-imx7.dtb: Warning (simple_bus_reg): Node /soc/aips-bus@30000000/anatop@30360000/regulator-vdd1p0d missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move usbphynop1, usbphynop2, usbhypnop3, replicator and timer and nodes
from soc node to root node.
The nodes that have been moved do not have any register properties and thus
shouldn't be placed on the bus.
This fixes the following build warnings with W=1:
arch/arm/boot/dts/imx7d-cl-som-imx7.dtb: Warning (simple_bus_reg): Node /soc/replicator missing or empty reg/ranges property
arch/arm/boot/dts/imx7d-cl-som-imx7.dtb: Warning (simple_bus_reg): Node /soc/timer missing or empty reg/ranges property
arch/arm/boot/dts/imx7d-cl-som-imx7.dtb: Warning (simple_bus_reg): Node /soc/aips-bus@30800000/usbphynop1 missing or empty reg/ranges property
arch/arm/boot/dts/imx7d-cl-som-imx7.dtb: Warning (simple_bus_reg): Node /soc/aips-bus@30800000/usbphynop3 missing or empty reg/ranges property
arch/arm/boot/dts/imx7d-cl-som-imx7.dtb: Warning (simple_bus_reg): Node /soc/aips-bus@30800000/usbphynop2 missing or empty reg/ranges property
Based on a patch from Simon Horman for r8a7795.dtsi.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove unneeded label and unit address in order to fix the following
build warnings with W=1:
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2000000/iomuxc-gpr@20e0000/ipu1_csi0_mux@34 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2000000/iomuxc-gpr@20e0000/ipu1_csi1_mux@34 has a unit name, but no
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pass the reg properties for mipi nodes in order to fix the
following build warnings with W=1:
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@1/endpoint@0 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@1/endpoint@1 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@2/endpoint@0 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@2/endpoint@1 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@3/endpoint@0 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@3/endpoint@1 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@4/endpoint@0 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@4/endpoint@1 has a unit name, but no reg property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move tempmon, ldb and pmu nodes from soc node to root node.
The nodes that have been moved do not have any register properties and thus
shouldn't be placed on the bus.
This fixes the following build warnings with W=1:
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (simple_bus_reg): Node /soc/aips-bus@2000000/tempmon missing or empty reg/ranges property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (simple_bus_reg): Node /soc/aips-bus@2000000/ldb missing or empty reg/ranges property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (simple_bus_reg): Node /soc/pmu missing or empty reg/ranges property
Based on a patch from Simon Horman for r8a7795.dtsi.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move pmu, usbphy0 and usbphy1 nodes from soc node to root node.
The nodes that have been moved do not have any register properties and thus
shouldn't be placed on the bus.
This fixes the following build warnings with W=1:
arch/arm/boot/dts/imx53-ard.dtb: Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
arch/arm/boot/dts/imx53-ard.dtb: Warning (simple_bus_reg): Node /soc/aips@50000000/usbphy-0 missing or empty reg/ranges property
arch/arm/boot/dts/imx53-ard.dtb: Warning (simple_bus_reg): Node /soc/aips@50000000/usbphy-1 missing or empty reg/ranges property
arch/arm/boot/dts/imx53-ard.dtb: Warning (simple_bus_reg): Node /soc/pmu missing or empty reg/ranges property
Based on a patch from Simon Horman for r8a7795.dtsi.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This node is for Low Power General Purpose Register which can
be used as Non-Volatile Storage.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The timer fixed interval period pulse generator register
is used to generate periodic pulses. The down count
register loads the value programmed in the fixed period
interval (FIPER). At every tick of the timer accumulator
overflow, the counter decrements by the value of
TMR_CTRL[TCLK_PERIOD]. It generates a pulse when the down
counter value reaches zero. It reloads the down counter
in the cycle following a pulse. To use the TMR_FIPER1
register to generate a 1 PPS event, the value
(10^9 nanoseconds) - TCLK_PERIOD should be programmed.
It should be 999999995 not 999999990 since TCLK_PERIOD
is 5.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds the partitions definition for the SPI NOR to provide
backward compatibility with the documented[1] layout used with
Boundary Devices BSP.
1. https://boundarydevices.com/boot-flash-access-linux/
It exports to Linux:
mtd0: bootloader
mtd1: env
mtd2: splash
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam suggested using GPIO_ACTIVE_HIGH in the gpio specification
for the USB regulators. Change them to conform.
Suggested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add Cubox-i and Hummingboard variants for v1.5 SOMs, where the SOM has
eMMC fitted.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add Cubox-i and Hummingboard variants for v1.5 SOMs, which have TI
Wi-Fi instead of Broadcom Wi-Fi. This variant does not include
SOM eMMC support.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node names are supposed to be generic, fix the RTC and codec node
names for both Hummingboard and Cubox-i.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Make the regulators match the schematic - name the regulators after
one of their schematic supply names, and arrange them into their
heirarchy.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the SD card regulator, which allows the SD card power to be switched
on/off.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Rev 1.5 microsoms include eMMC support on-board. Add a microsom include
file which can be used to add support for this.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the TI Wi-Fi WL1837 device on SolidRun's revision
1.5 microsoms.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a 3.3V regulator for devices connected to the vcc_3v3 supply
signal on the microsom.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SDIO clock is really the Broadcom clock. Rename it as such.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are two variants of the imx6qdl som: one with Broadcom Wi-Fi and
another with Texas Instruments Wi-Fi. The two Wi-Fi devices require
different DT bindings, so it's necessary to split out the Broadcom
specifics.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use real iomuxc values rather than preserving the boot loader value for
the SOMs ethernet.
Suggested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move the microsom includes into the .dts files so different options can
be accomodated at the lowest level.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Jon and myself feel that "imx6qdl-microsom" is too generic a name for
SolidRun's microsom - some other manufacturer could have their own
microsom. Change the name to the shorter "imx6qdl-sr-som".
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As all SolidRun microsoms are fitted with an AR8035, it's pointless
having the ethernet support as a separate include file. Move the
AR8035 support into the main imx6qdl-microsom file.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The regulators node is redundant, and serves no useful function.
Remove it from i.MX6 SolidRun platforms.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
UDOO board has a possibility to disable most of imx6 SoC power supplies via
"EN_5V" signal, which is connected to "NANDF_D4" pad.
This reduces current consumption after shutdown from ~350 mA to ~40 mA and
prevents a SoC watchdog from starting it again on its own after the
watchdog timeout expires (previously it was not possible to shut down the
SoC permanently if its watchdog was ever enabled since it was still ticking
after the shutdown).
Unfortunately, this does not extinguish the "Power" LED (as it is powered
from an always-on voltage regulator).
To power the SoC up again press the power button (SW2, the one with a long
shaft).
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As explained in Documentation/devicetree/bindings/net/fsl-fec.txt the
phy-reset-gpios is active high only if the 'phy-reset-active-high' is
present.
As 'phy-reset-active-high' is not used here, fix the device tree
description by passing GPIO_ACTIVE_LOW flag.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
HDMI_TX_CEC_LINE pin is used for CEC, so pass it in the device tree.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On imx6qdl-sabreauto the HDMI DDC bus is connected to I2C2, so
pass the 'ddc-i2c-bus' property accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is not recommended to place regulators inside "simple-bus", so
move them out. The motivation for doing this is to make it easier to
adding new regulators.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently the imx pci driver fails to probe on i.MX6SX.
Fix the PCI representation so that the driver can be probed and
PCI devices can be detected.
Tested on a im6sx-sdb board:
00:00.0 Class 0604: 16c3:abcd
01:00.0 Class 0280: 8086:08b1
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
AC'97 interface RXD and TXC pins are only used as SoC inputs, let's disable
pad drivers for them so we will be protected if, for example, TCLKDIR is
set by mistake in AUDMUX and causes TXC pin to be configured as an output.
This also changes pull direction on these pins from pull-up to pull-down
to match what the board AC'97 CODEC chip (VT1613) has on these pins.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Commit a22950c888 (mmc: sdhci-of-esdhc: add quirk
SDHCI_QUIRK_BROKEN_TIMEOUT_VAL for ls1021a) added logic to the driver to
enable the broken timeout val quirk for ls1021a, but did not add the
corresponding compatible string to the device tree, so it didn't really
have any effect. Fix that.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ls1021a esdhc had been enabled in uboot,
but it had not been enabled it in kernel,
So set the esdhc's status to "okay".
Signed-off-by: yinbo.zhu <yinbo.zhu@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The two Ethernet switches have an AT24C512 each. This is a 64K device,
not 512 bytes as currently listed in the device tree.
Reported-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
"usb-nop-xceiv" is using the phy binding, but is missing #phy-cells
property. This is probably because the binding was the precursor to the phy
binding.
Fixes the following warning in i.MX dts files:
Warning (phys_property): Missing property '#phy-cells' in node ...
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This makes sure that the battery backed RTC is always the
primary one, regardless of the driver probe ordering.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This renames the audio device to "Front" in order to match the RDU2
naming, which makes it easier for a unified userspace to deal with
both boards.
Also rename the phandle for the headphone amplifier to more closely
resemble the RDU2 DTS.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are 0 ohm resistors that allow selecting the EDID I2C port to
be I2C1 or I2C2.
On revd1 the 0 ohm resistors are populated in such a way that the I2C2
is used as DDC I2C bus, so fix it accordingly.
Reported-by: Luís Mendes <luis.p.mendes@gmail.com>
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx7s/imx7d has the ptp interrupt newly added as well.
For imx7, "int0" is the interrupt for queue 0 and ENET_MII
"int1" is for queue 1
"int2" is for queue 2
For imx6sx, "int0" handles all 3 queues and ENET_MII
And of course, the "pps" interrupt is for the PTP_CLOCK_PPS interrupts
This will help document what each interrupt does.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is needed for the bootloader to patch in the correct MAC address.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The following build warning is seen with W=1:
Warning (unit_address_vs_reg): Node /soc/aips@60000000/ethernet@63fec000/ethernet-phy@0 has a unit name, but no reg property
Fix this warning by adding reg property from such node and, consequently,
includes a mdio node into the fec node, with the 'address-cells' and
'size-cells' to avoid these other following warnings:
Warning (reg_format): "reg" property in /soc/aips@60000000/ethernet@63fec000/ethernet-phy@0 has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells value for /soc/aips@60000000/ethernet@63fec000/ethernet-phy@0
Warning (avoid_default_addr_size): Relying on default #size-cells value for /soc/aips@60000000/ethernet@63fec000/ethernet-phy@0
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Tested-by: Lothar Waßmann <LW@karo-electronics.de>
Acked-by: Lothar Waßmann <LW@karo-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add QSPI node support, and this function is disabled by default
This setting could be overwritten in board-level definitions
Signed-off-by: SZ Lin <sz.lin@moxa.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a Device Tree for the Allo.com Sparky SBC.
Acked-by: Sudeep Kumar <sudeepkumar@cem-solutions.net>
[AF: Adjusted SPDX-License-Identifier style]
Signed-off-by: Andreas Färber <afaerber@suse.de>
This adds the TVE200/TVC TV-encoder and the Ilitek ILI9322 panel
to the DIR-685 device tree.
This brings graphics to this funky router and it is possible to
even run a console on its tiny screen.
Incidentally this requires us to disable the access to the
parallel (NOR) flash, as the communication pins to the panel
are shared with the flash memory.
To access the flash, a separate kernel with the panel disabled
and the flash enabled should be booted. The pin control selecting
whether to use the lines cannot be altered at runtime due to
hardware constraints.
Cc: David Lechner <david@lechnology.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These GPIOs are used in open drain mode, so make sure to
flag them as such. Use the new separate scl/sda line
GPIO bindings.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the missing clock to CA7 CPU1 node.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
dtc points out that the parent node of the interrupt controllers is not
actually an interrupt controller itself, and lacks an #interrupt-cells
property:
arch/arm/boot/dts/tango4-vantage-1172.dtb: Warning (interrupts_property): Missing #interrupt-cells in interrupt-parent /soc/interrupt-controller@6e000
This removes the annotation.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
dtc warns about two 'clocks' properties that have an extraneous '1'
at the end:
arch/arm/boot/dts/ls1021a-qds.dtb: Warning (clocks_property): arch/arm/boot/dts/ls1021a-twr.dtb: Warning (clocks_property): Property 'clocks', cell 1 is not a phandle reference in /soc/i2c@2180000/mux@77/i2c@4/sgtl5000@2a
arch/arm/boot/dts/ls1021a-qds.dtb: Warning (clocks_property): Missing property '#clock-cells' in node /soc/interrupt-controller@1400000 or bad phandle (referred from /soc/i2c@2180000/mux@77/i2c@4/sgtl5000@2a:clocks[1])
Property 'clocks', cell 1 is not a phandle reference in /soc/i2c@2190000/sgtl5000@a
arch/arm/boot/dts/ls1021a-twr.dtb: Warning (clocks_property): Missing property '#clock-cells' in node /soc/interrupt-controller@1400000 or bad phandle (referred from /soc/i2c@2190000/sgtl5000@a:clocks[1])
The clocks that get referenced here are fixed-rate, so they do not
take any argument, and dtc interprets the next cell as a phandle, which
is invalid.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlo7+7IQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgWKzCACiOs6rif6zIG6hBl29S5q8BGIwD1K234Br
4u05OIUzlol41p0cp5wBBuYyUd9jQdXhYVZLVk+iKsygOJEZY/u1jKa1gy6nVQxu
Uqb3CgVq0QjbGIMWEIssOE2oML4Rhgx9dmMhVoVYgP+A1yFiGRnevp0ZKlYc+iHM
kqaZfno2WWBARgLMuJ90kyaZhUSyjweWi3rJiFCc5Hx0oeX/ENKFyI0NftUfjkD1
2bgDAkRiOK4ieK8LqM1BbUvhKPvEP5mR/hZsqa7AykXf+oYKk9ZAxoXx2EndyCN0
dbQppp4fqvWusTDP+xi1lrEq5JVhPHuBtcR1ntzfSOF1D3K00PA8
=b8Nk
-----END PGP SIGNATURE-----
Merge tag 'v4.16-rockchip-dts32-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "Rockchip dts32 changes for 4.16" from Heiko Stübner:
Just the reset property for the rk3066a-rayeager emac phy
* tag 'v4.16-rockchip-dts32-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add reset property for rk3066a-rayeager emac phy
Add and enable the sdhci2 slot and the pinctrl configuration.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
- update mmc nodes for mt7623
- mt7623 change mmc card detection pin to active low
- mt7623 set unit address to lower case
-----BEGIN PGP SIGNATURE-----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=d/4Y
-----END PGP SIGNATURE-----
Merge tag 'v4.15-next-dts32' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into next/dt
Pull "arm: Updates of armv7 DTS for v4.15-next" from Matthias Brugger:
- add reset cells mt2701 and mt7623 ethsys
- update mmc nodes for mt7623
- mt7623 change mmc card detection pin to active low
- mt7623 set unit address to lower case
* tag 'v4.15-next-dts32' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
dt-bindings: ARM: Mediatek: Fix ethsys documentation
arm: mt7: dts: Remove leading 0x and 0s from bindings notation
arm: dts: mt7623: fix card detection issue on bananapi-r2
arm: dts: mt7623: update mmc related nodes with the appropriate fallback
arm: dts: mt2701: Add reset-cells
arm: dts: mt7623: Update ethsys binding
These changes enable the video decoder engine found on Tegra20 SoCs.
-----BEGIN PGP SIGNATURE-----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=bS8w
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.16-arm-dt' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
Pull "ARM: tegra: Device tree changes for v4.16-rc1" from Thierry Reding:
These changes enable the video decoder engine found on Tegra20 SoCs.
* tag 'tegra-for-4.16-arm-dt' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Add video decoder on Tegra20
ARM: tegra: Add device tree node to describe IRAM on Tegra20
1. Add sound support to Odroid XU4 (and adjustments to Odroid XU3).
2. Enable WiFi on Trats2.
3. Add CPU perf counters to Exynos54xx.
4. Add power domains to certain chipsets.
5. Add Exynos4412 ISP clock controller which finally solves freezes when
accessing ISP clocks while having the ISP power domain turned off.
6. Add Pseudo and True RNG to Exynos5.
7. Minor fixes for Trats2, Odroid XU3/XU4, Exynos5410.
8. Cleanup of some of DTC warnings
-----BEGIN PGP SIGNATURE-----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=auEd
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Pull "Samsung DTS ARM changes for 4.16" from Krzysztof Kozłowski:
1. Add sound support to Odroid XU4 (and adjustments to Odroid XU3).
2. Enable WiFi on Trats2.
3. Add CPU perf counters to Exynos54xx.
4. Add power domains to certain chipsets.
5. Add Exynos4412 ISP clock controller which finally solves freezes when
accessing ISP clocks while having the ISP power domain turned off.
6. Add Pseudo and True RNG to Exynos5.
7. Minor fixes for Trats2, Odroid XU3/XU4, Exynos5410.
8. Cleanup of some of DTC warnings
* tag 'samsung-dt-4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Use lower case hex addresses in node unit addresses
ARM: dts: exynos: Add nodes for True Random Number Generator
ARM: dts: exynos: Add DT nodes for PRNG in Exynos5 SoCs
ARM: dts: exynos: Add G3D power domain to Exynos5250
ARM: dts: exynos: Add audio power domain to Exynos5250
ARM: dts: exynos: Fix power domain node names for Exynos5250
ARM: dts: exynos: Add missing interrupt-controller properties to Exynos5410 PMU
ARM: dts: exynos: Add audio power domain support to Exynos542x SoCs
ARM: dts: exynos: Fix property values of LDO15/17 for Odroid XU3/XU4
ARM: dts: exynos: Add Exynos4412 ISP clock controller
ARM: dts: exynos: Move G2D node to exynos5.dtsi
ARM: dts: exynos: Add CPU perf counters to Exynos54xx boards
ARM: dts: exynos: Remove duplicate definitions of SSS nodes for Exynos5
ARM: dts: exynos: Add bcm4334 device node to Trats2
ARM: dts: exynos: Correct Trats2 panel reset line
ARM: dts: exynos: Add sound support for Odroid XU4
ARM: dts: exynos: Switch to dedicated Odroid XU3 sound card binding
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJaNXUrAAoJEEEQszewGV1zLPEP/0QQ9i4UCR+hglmUOPHAe1eu
h9HccxmtqzWOKWcknBoL5DtM7gHhTLW1ty9yCs4vKwzUevr+NJNenqTlkDnKcQV4
/mxYePPnkDB6o26pg0CZOaCi5w1q54R9gOa9QNDomNSG+iOsZwdjOUBUIURe1xmU
eekOBT++cmHK56D2/lHZxXNy15/P1B0KmXRUYtORDWKy9cqgYhREAAHGBCL5vTBM
skIze8zkb1VZ34rWLfJwxoXnMOGCpGO+EN6xQRZOuxRYwys5Hfjl/5WcHo/Mvk8H
lgiLCtF2K+l6MVc8qAuDFsUlyZvKSTPxBVdx4nlRiCJ+s0nbAOdtS2wsEoRNTC70
DcbYsuO+K4Sfmn8rAUAAnQXlFDVxZQuoZb3+pxl5TugktSVJN38hdcp76k9XnGt8
6DjU/kuUbOR2mjQqF6xNUxT83rEm0/MlmH2yGgTlIXCRz7LUATGODjWIO7QwX0gO
kyLT191VajQM6ewD4TLpVbapwatyEskYIDZ86oUdP3uIsut51hZbKELBmJt/bFes
8ys5Gd6VMZT7bI/P4DOWCVfASNgnAP4duvTQJS1VA1H1iyG7Rv+7OEPICqa+5ytD
50DcG3iwfVJEMsf7NmOoHNVLakKFSdSIue8xP4HdnbL9JaTWx70LlYAXckerN+nO
qAXFGpNrpATM8TUvfy5y
=10ji
-----END PGP SIGNATURE-----
Merge tag 'gemni-dts-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
Gemini DTS updates, take one
* tag 'gemni-dts-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: Add basic devicetree for D-Link DNS-313
ARM: dts: Add ethernet PHYs to the a bunch of Geminis
These changes are mostly improvments for various devices.
Note that these are based on my earlier fixes branch
omap-for-v4.15/fixes-dt to avoid a pointless merge conflict
between a fix and removal. The summary of changes is:
- Fix audio codec reset pin for am335x-pepper and n900, this
has been always broken and won't get fixed until the related
driver changes are also merged in for v4.16, so not urgent
- Fix tps65917 powerhold property for dra76-evm
- Changes to logicpd boards to remove MTD partition information
and to add support for omap35xx variants by setting up common
dts files for the logicpd boards
- Disable dra7 USB metastability workaround, this won't do
anything until the related driver changes are also merged
into v4.16, so not urgent
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEkgNvrZJU/QSQYIcQG9Q+yVyrpXMFAloynnkRHHRvbnlAYXRv
bWlkZS5jb20ACgkQG9Q+yVyrpXMoCRAAt0FUyB27k7XKtsull1vepLy4M7w6RRZE
hCYsdgCznXSwrp46ZL09HkakEa8Vk+D1PZUtNf4ZU5lB/wi1zZ/bJHsNewCaBYHU
UkyjTP/EaM2gekb/v0fQ7zEew2xipZ6rGW+mHz7t3cX1WzwJRWcWEqcVWtIN0sjG
VAyr1VZwt2s0j+f8n+BjhCf1gkoZnQZt2+PU3+H/jh0P9tLEyZdq/P1npTLxm1Tj
qvYMYkfbaamX+RC7JAvO3LoIF4fxAocLdbuVQk+5Vg2xVtOkRDhnJCUzZdgaQ5f4
Mlxo93j0TZFwJI+rhDBgZGJawi/PgEv4xNCGYOgG6wXW5j5Af3kihBBdz2nbx1tY
svzeoS+bE7T+gGqmzSGH1CzZUCyP5B4Ue49JrNsYsGFgXXbwjd0k1sYcjORx+VRg
iYfd+8NdwWGlNX5KtYJ01BMitRqIDADDeeGibeGPsj2VAryAPuIGpiD7ux7YPSDV
/kpPzBA7Ju9iTfHC5s/4QzhZPggHkTtmt/vgs60yZ8GGTBohhByMlg6yqItYLWc5
4x6jBPIgs8Zay0CAtXpGszoMNgOH3a9B8+3RwZIHg7jtCzKEyS8wDmAGvLuljZ5i
VOUpqmhpyl2OPVJcNdkUpH65dueHW+qiCK8ytAwnbqpwDN/CUtHMExZrNtWlpndn
hqE7Fm22smM=
=jzFR
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.16/dt-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "Dts related changes for omaps for v4.16 merge window" from Tony
Lindgren:
These changes are mostly improvments for various devices.
Note that these are based on my earlier fixes branch
omap-for-v4.15/fixes-dt to avoid a pointless merge conflict
between a fix and removal. The summary of changes is:
- Fix audio codec reset pin for am335x-pepper and n900, this
has been always broken and won't get fixed until the related
driver changes are also merged in for v4.16, so not urgent
- Fix tps65917 powerhold property for dra76-evm
- Changes to logicpd boards to remove MTD partition information
and to add support for omap35xx variants by setting up common
dts files for the logicpd boards
- Disable dra7 USB metastability workaround, this won't do
anything until the related driver changes are also merged
into v4.16, so not urgent
* tag 'omap-for-v4.16/dt-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Move move WiFi bindings to logicpd-torpedo-37xx-devkit
ARM: dts: Add minimal support for LogicPD OMAP35xx Torpedo devkit
ARM: dts: Move most of logicpd-torpedo-37xx-devkit to logicpd-torpedo-baseboard
ARM: dts: Add minimal support for LogicPD OMAP35xx SOM-LV devkit
ARM: dts: Move most of logicpd-som-lv-37xx-devkit.dts to logicpd-som-lv-baseboard.dtsi
ARM: dts: dra7: Add missing hdmi audio DMA channel information
ARM: dts: dra7: Disable USB metastability workaround for USB2
ARM: dts: omap3: logicpd kits: Remove partition information
ARM: dts: DRA76-EVM: Set powerhold property for tps65917
ARM: dts: omap3-n900: Fix the audio CODEC's reset pin
ARM: dts: am335x-pepper: Fix the audio CODEC's reset pin
This branch contains a series of dts changes from Tero Kristo to
start using clkctrl clocks.
Note that this branch is based on a merge of omap-for-v4.16/soc-signed
and an immutable commit from Tero Kristo fe7020e64f ("clk: ti: omap4:
clkctrl data fixes for opt-clocks") that is also in clk-next.
-----BEGIN PGP SIGNATURE-----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=uhHY
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.16/dt-clk-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "Clock related dts changes for omaps for v4.16 merge window" from
Tony Lindgren:
This branch contains a series of dts changes from Tero Kristo to
start using clkctrl clocks.
Note that this branch is based on a merge of omap-for-v4.16/soc-signed
and an immutable commit from Tero Kristo fe7020e64f ("clk: ti: omap4:
clkctrl data fixes for opt-clocks") that is also in clk-next.
* tag 'omap-for-v4.16/dt-clk-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (57 commits)
ARM: dts: dm816x: add clkctrl nodes
ARM: dts: dm814x: add clkctrl nodes
ARM: dts: am43xx: add clkctrl nodes
ARM: dts: am33xx: add clkctrl nodes
ARM: dts: dra7: add clkctrl nodes
ARM: dts: omap5: add clkctrl nodes
ARM: dts: omap4: add clkctrl nodes
ARM: dts: dm816x: add bus functionality to base PRCM node
ARM: dts: am43xx: add bus functionality to base PRCM node
ARM: dts: am33xx: add bus functionality to base PRCM node
ARM: dts: dra7: add bus functionality to base PRCM nodes
ARM: dts: omap4: add bus functionality to base PRCM nodes
ARM: dts: omap5: add bus functionality to base PRCM nodes
ARM: dts: dm816x: add fck under timers1/2
ARM: dts: dm814x: add fck under timers1/2
ARM: dts: dra7: add fck under timer1
ARM: dts: am43xx: add fck under timers1/2
ARM: dts: am33xx: add fck under timers1/2
ARM: dts: omap4: add fck under timer1
ARM: dts: omap5: add fck under timer1
...
work on DM365 and a fix for battery voltage monitoring on Lego EV3.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=GZm0
-----END PGP SIGNATURE-----
Merge tag 'davinci-fixes-for-v4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes
Pull "TI DaVinci fixes for v4.15" from Sekhar Nori:
DaVinci fixes for v4.15 consiting of fixes to make EDMA and MMC/SD
work on DM365 and a fix for battery voltage monitoring on Lego EV3.
* tag 'davinci-fixes-for-v4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: fix mmc entries in dm365's dma_slave_map
ARM: dts: da850-lego-ev3: Fix battery voltage gpio
ARM: davinci: Add dma_mask to dm365's eDMA device
ARM: davinci: Use platform_device_register_full() to create pdev for dm365's eDMA
on the rk3066a-marsboard to make it not fail from cpufreq changes.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlosSE4QHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgRhMCACXcPJmWvjPRQwrpFrFOrHUfgsku46CFl2a
AWmN5wGB2pStM1R/1HsfrfO0YXb5e9UESEwyQzb1/DEoAnES5aFrZqnuPSSHr/9W
cZR8fDRk69cxMILdCy25xmWeAmhPTJUWTPwdhfSkINmf0+DcPehKr97xVyzEcVK3
LMczvzPUSuipciQbVdR8bTkVy05ToHJctN+ri3Ux9SqrGZcW86W/v5mRnRVxxvXU
NcdEIB1/IC9nHPYYRJbUvrEgLIzHt21KkS3GEmCI3kf4t7qsY28VkVfsoqrIQMA9
/ennO0r6df+7sSzQXI25lERWMHk+gSSlq4z3jguI6b8NmAFBynMh
=CZn2
-----END PGP SIGNATURE-----
Merge tag 'v4.15-rockchip-dts32fixes-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Pull "Rockchip dts32 fixes for 4.15" from Heiko Stübner:
Removed another trailing interrupt-cell 0 and added the cpu regulator
on the rk3066a-marsboard to make it not fail from cpufreq changes.
* tag 'v4.15-rockchip-dts32fixes-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: fix rk3288 iep-IOMMU interrupts property cells
ARM: dts: rockchip: add cpu0-regulator on rk3066a-marsboard
After ti-opp-supply driver is in place to provide AVS Class0 and abb
regulator scaling support let's enable 1.5GHz for the cpu.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the OPP supply node for the MPU voltage rail to provide the
information needed by the ti-opp-supply driver to enable AVS Class 0.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a vbb-supply phandle to the cpus node and also add an additional
triplet of voltages for each OPP in the operating-points-v2 table to
make use of the multi regulator support in the OPP core and provide the
vbb regulator for use by the ti-opp-supply driver.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise we cannot use generic OF_DEV_AUXDATA match without listing
all the compatibles separately for OF_DEV_AUXDATA. Let's also update the
binding accordingly.
Let's also fix omap4.dtsi to use "ti,sysc-omap4-sr" compatible as we
have documented in the binding. This was not noticed earlier as we're
still probing SmartReflex driver with platform data.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This should have always been 8.
Fixes: db4d6d9d80 ("ARM: dts: aspeed: Correctly order UART nodes")
Cc: stable@vger.kernel.org
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
BeagleBone Blue: can: enable the dedicated can connector.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Cc: Jason Kridner <jkridner@beagleboard.org>
Cc: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
BeagleBone Blue: usarts: enable all the dedicated usart connectors.
DSM2/uart4: on the Blue, this is a recieve only interface.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Cc: Jason Kridner <jkridner@beagleboard.org>
Cc: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the correct IRQ gpio pin on the BeagleBone Blue to allow the
wl1835 wireless module to actually work.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Cc: Jason Kridner <jkridner@beagleboard.org>
Cc: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since SoC specific compatible strings are used for PCIe in
dra74x.dtsi and dra72x.dtsi, remove the compatible property
from dra7.dtsi which uses the deprecated compatible string.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DRA76 EVM has a 4-lane PCIe connector and DRA76 can support x2 lanes.
Enable both the PCIe lanes here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use dra72 specific compatible string for PCIe while preserving
the older compatible.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use dra74 specific compatible string for PCIe while preserving
the older compatible. While at that add a new label for the
2nd instance of pcie.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ti,syscon-lane-sel and ti,syscon-lane-conf properties specific to enable
PCIe x2 lane mode are added here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
am574x-idk is similar to am572x-idk with am574x SoC. So create
a common file for both evms and include SoC dtsi as needed.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM437x IDK has a TPS386000 supply voltage supervisor on the VDD_MPU rail
set to trigger undervoltage condition at 0.96V. Because of this, OPP50,
which is normally configured to 300MHz at 0.95V, must be disabled to
avoid triggering the undervoltage condition. Also mark OPP100 as the
suspend-opp as it is now our lowest OPP.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can remove the unnecessary "omapdss," prefix because
the omapdrm driver takes care of it when matching with
the driver table.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* Convert to named i2c-gpio bindings
Geert Uytterhoeven says "Commits 7d29f509d2 ("dt-bindings: i2c:
i2c-gpio: Add support for named gpios") and 05c7477885 ("i2c: gpio:
Add support for named gpios in DT") introduced named i2c-gpio DT
bindings, and deprecated the more error-prone unnamed variant.
This patch series switches all Renesas boards to the new bindings, and
adds the missing GPIO_OPEN_DRAIN I/O flags, which were implicitly
assumed before..."
... Note that after this series is applied, the i2c-gpio buses are no
longer detected when booting new DTBs on old (v4.14 and older) kernels,
which should not be an issue. Booting old DTBs on new kernels is not
affected."
* Update DTS for CMT DT binding rework
Geert Uytterhoeven says "This patch series updates the CMT device nodes
in the various Renesas DTS files sh_cmt clocksource driver for the recent
DT binding rework that was merged in v4.14-rc1 and v4.15-rc1..."
* Add SMP support to r8a7794 (R-Car E2) SoC
Sergei Shtylyov says "Add the device tree node for the Advanced Power
Management Unit (APMU). Use the "enable-method" prop to point out that
the APMU should be used for the SMP support."
* Correct primary compatible value for eeprom
on r7s72100 (RZ/A1H) genmai and r8a7791 (R-Car M2-W) koelsh boards
Geert Uytterhoeven says "The Renesas part numbers of the two-wire serial
interface EEPROMs do not follow the 24Cxx pattern, but the R1EX24xxx
pattern.
Hence change the primary compatible values to the appropriate variant of
"renesas,r1ex24xxx", like is already done on Gose.""
* Move cec_clock to root node on r8a7791 (R-Car M2-W) koelsh board
r8a7791 (R-Car M2-W) koelsh board
* Use R-Car SDHI and Ether Gen1 and 2 fallback compat strings
Use recently posted R-Car SDHI and Ether Gen 1 and 2 fallback
compat strings in the DT of Renesas ARM based SoCs.
* Add IIC cores to dtsi of r8a7745 (RZ/G1E) SoC
* Rework DT architecture for r8a7745 (RZ/G1E) iW-RainboW-G22D development
platform and add serial support.
Fabrizio Castro says "... define a new DT architecture for the
iW-RainboW-G22D SODIMM Development Platform to include the configuration
with the HDMI daughter board and to define the serial interfaces."
* Add USB function support to
r8a7745 (RZ/G1E) iW-RainboW-G22D development platform
* Add PCIEC and ttySC3 support to r8a7743 (RZ/G1M) iW-RainboW-G20M-Qseven SoM
* Add VIN support to r8a7743 (RZ/G1M) and r8a7745 (RZ/G1E) SoCs
* Add CAN and HDMI support to r8a7743 (RZ/G1M) iW-RainboW-G20D-Qseven and
r8a7745 (RZ/G1E) iW-RainboW-G22D development platforms
-----BEGIN PGP SIGNATURE-----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=Yk5x
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Renesas ARM Based SoC DT Updates for v4.16" from Simon Horman:
* Convert to named i2c-gpio bindings
Geert Uytterhoeven says "Commits 7d29f509d2 ("dt-bindings: i2c:
i2c-gpio: Add support for named gpios") and 05c7477885 ("i2c: gpio:
Add support for named gpios in DT") introduced named i2c-gpio DT
bindings, and deprecated the more error-prone unnamed variant.
This patch series switches all Renesas boards to the new bindings, and
adds the missing GPIO_OPEN_DRAIN I/O flags, which were implicitly
assumed before..."
... Note that after this series is applied, the i2c-gpio buses are no
longer detected when booting new DTBs on old (v4.14 and older) kernels,
which should not be an issue. Booting old DTBs on new kernels is not
affected."
* Update DTS for CMT DT binding rework
Geert Uytterhoeven says "This patch series updates the CMT device nodes
in the various Renesas DTS files sh_cmt clocksource driver for the recent
DT binding rework that was merged in v4.14-rc1 and v4.15-rc1..."
* Add SMP support to r8a7794 (R-Car E2) SoC
Sergei Shtylyov says "Add the device tree node for the Advanced Power
Management Unit (APMU). Use the "enable-method" prop to point out that
the APMU should be used for the SMP support."
* Correct primary compatible value for eeprom
on r7s72100 (RZ/A1H) genmai and r8a7791 (R-Car M2-W) koelsh boards
Geert Uytterhoeven says "The Renesas part numbers of the two-wire serial
interface EEPROMs do not follow the 24Cxx pattern, but the R1EX24xxx
pattern.
Hence change the primary compatible values to the appropriate variant of
"renesas,r1ex24xxx", like is already done on Gose.""
* Move cec_clock to root node on r8a7791 (R-Car M2-W) koelsh board
r8a7791 (R-Car M2-W) koelsh board
* Use R-Car SDHI and Ether Gen1 and 2 fallback compat strings
Use recently posted R-Car SDHI and Ether Gen 1 and 2 fallback
compat strings in the DT of Renesas ARM based SoCs.
* Add IIC cores to dtsi of r8a7745 (RZ/G1E) SoC
* Rework DT architecture for r8a7745 (RZ/G1E) iW-RainboW-G22D development
platform and add serial support.
Fabrizio Castro says "... define a new DT architecture for the
iW-RainboW-G22D SODIMM Development Platform to include the configuration
with the HDMI daughter board and to define the serial interfaces."
* Add USB function support to
r8a7745 (RZ/G1E) iW-RainboW-G22D development platform
* Add PCIEC and ttySC3 support to r8a7743 (RZ/G1M) iW-RainboW-G20M-Qseven SoM
* Add VIN support to r8a7743 (RZ/G1M) and r8a7745 (RZ/G1E) SoCs
* Add CAN and HDMI support to r8a7743 (RZ/G1M) iW-RainboW-G20D-Qseven and
r8a7745 (RZ/G1E) iW-RainboW-G22D development platforms
* tag 'renesas-dt-for-v4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (61 commits)
ARM: dts: alt: Convert to named i2c-gpio bindings
ARM: dts: koelsch: Convert to named i2c-gpio bindings
ARM: dts: lager: Convert to named i2c-gpio bindings
ARM: dts: armadillo800eva: Convert to named i2c-gpio bindings
ARM: dts: sh73a0: Remove CMT renesas,channels-mask
ARM: dts: r8a7794: Remove CMT renesas,channels-mask
ARM: dts: r8a7793: Remove CMT renesas,channels-mask
ARM: dts: r8a7791: Remove CMT renesas,channels-mask
ARM: dts: r8a7790: Remove CMT renesas,channels-mask
ARM: dts: r8a7740: Remove CMT renesas,channels-mask
ARM: dts: r8a73a4: Remove CMT renesas,channels-mask
ARM: dts: r8a7794: Update CMT compat strings
ARM: dts: r8a7793: Update CMT compat strings
ARM: dts: r8a7791: Update CMT compat strings
ARM: dts: r8a7790: Update CMT compat strings
ARM: dts: r8a73a4: Update CMT compat string
ARM: dts: r8a7794: Add SMP support
ARM: dts: genmai: Correct primary compatible value for eeprom
ARM: dts: koelsch: Correct primary compatible value for eeprom
ARM: dts: r8a7745: add VIN dt support
...
ARCH_S3C24XX is a very exceptional platform that some DT files in
arch/arm/boot/dts/, but does not select USE_OF.
All the other platforms with DT files correctly select USE_OF
directly or indirectly (Most of them are either ARCH_MULTIPLATFORM
or ARM_SINGLE_ARMV7M).
With ARCH_S3C24XX fixed, "ifeq ($(CONFIG_OF),y)" in DT Makefile
can be deleted.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit 1cb686c08d ("ARM: dts: exynos: Add status property to Exynos 542x
Mixer nodes") disabled the Mixer node by default in the DTSI and enabled
for each Exynos 542x DTS. But unfortunately it missed to enable it for the
Exynos5800 Peach Pi machine, since the 5800 is also an 542x SoC variant.
Fixes: 1cb686c08d ("ARM: dts: exynos: Add status property to Exynos 542x Mixer nodes")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Official vendor string is now "tpo" and not "toppoly".
Requires patch "omapdrm: panel: fix compatible vendor string for td028ttec1"
so that the driver understands both.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add basic panel support for the Nokia N950. It must be tweaked a
little bit later, since the panel was built into the device
upside-down. Also the first 5 and the last 5 pixels are covered
by plastic.
Signed-off-By: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This improves LCD support for the Droid 4.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable sound PIO support on carrier board.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic r8a7745(RZ/G1E) part of the sound device node.
This patch is based on the r8a7794 sound work by Sergei Shtylyov.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the external audio clocks required by the sound driver.
Boards that provide audio clocks need to override the clock frequencies.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Timer Pulse Unit has registers that lie outside the declared
register block. Enlarge the register block size to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The OpenBMC flash layout is used by Palmetto systems.
Add the unit name to the memory node to fix a warning with W=1.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
- Fix incorrect RAM size
- Remove alias; these are now specified in the dtsi
- Add newly upstreamed devices
- Include OpenBMC flash layout
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The Qanta Q71L BMC is an ASPEED ast2400 based BMC that is part of a
Qanta x86 server.
This adds the device tree description for most upstream components. It
is a squashed commit from the OpenBMC kernel tree.
Signed-off-by: Peter Hanson <peterh@google.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Rick Altherr <raltherr@google.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Zaius is a POWER9 platform announced at OpenPOWER Summit 2016. This adds
basic DTS support for its AST2500 BMC.
This adds the device tree description for most upstream components. It
is a squashed commit of all of the patches from the OpenBMC kernel tree.
Signed-off-by: Xo Wang <xow@google.com>
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Robert Lippert <rlippert@google.com>
Signed-off-by: Peter Hanson <peterh@google.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Rick Altherr <raltherr@google.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The Witherspoon BMC is an ASPEED ast2500 based BMC that is part of an
OpenPower Power9 server.
This adds the device tree description for most upstream components. It
is a squashed commit from the OpenBMC kernel tree.
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Signed-off-by: Matt Spinler <spinler@us.ibm.com>
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Edward A. James <eajames@us.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Brandon Wyman <bjwyman@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This is a layout used by OpenBMC systems. It describes the fixed flash
layout of a 32MB mtd device.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
In b24413180f ("License cleanup: add SPDX GPL-2.0 license identifier
to files with no license") these files had the GPL-2.0 licence added
automatically. Update them to be GPL 2.0+ in line with other IBM kernel
contributions.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
LPC snoop hardware on the ASPEED BMC, used for monitoring
host I/O port activity.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The PWM/tach unit has a clock and reset phandle. It needs both in order
to function correctly.
Signed-off-by: Joel Stanley <joel@jms.id.au>
--
v3:
Add the pwm reset phandle
This device tree will break existing kernels that do not have the clk
patches applied (no clocksource, as we don't know the speed of the APB
clock. You can boot if you pass a lpj value on the command line, but
won't have a uart).
Older device trees running with the newer kernel will function as well
as pre-4.16 kernels. That is, that some IP blocks (i2c, pwm/tach, adc)
will not work as the kernel lacks reset controller and clock enabling.
This is being changed as existing device trees use fixed-clocks in order
to boot without a clk driver. The newly added clk driver provides proper
clock support, including gating, so we move the device trees over to
properly request clocks.
The SCU compatible string is updated as the g4-scu string made it into
the tree before we decided on aspeed,astX000-<ip> as the format for the
strings. The old string will be removed from the bindings in a future
patch.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Ensure the ordering is correct and add all of the children in the SoC
device trees for the ast2400 and ast2500.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add a device tree node for the Video Decoder Engine found on Tegra20
SoCs.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
All Tegra20 SoCs contain 256 KiB IRAM, which is used to store resume
code and by the video decoder engine.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The timer and thermal-zones nodes do not have any register properties and
thus shouldn't be placed on the bus.
This problem is flagged by the compiler as follows:
$ make
DTC arch/arm/boot/dts/r8a7743-iwg20d-q7-dbcm-ca.dtb
arch/arm/boot/dts/r8a7743-iwg20d-q7.dtb: Warning (simple_bus_reg): Node /soc/thermal-zones missing or empty reg/ranges property
arch/arm/boot/dts/r8a7743-iwg20d-q7.dtb: Warning (simple_bus_reg): Node /soc/timer missing or empty reg/ranges property
arch/arm/boot/dts/r8a7743-iwg20d-q7-dbcm-ca.dtb: Warning (simple_bus_reg): Node /soc/thermal-zones missing or empty reg/ranges property
arch/arm/boot/dts/r8a7743-iwg20d-q7-dbcm-ca.dtb: Warning (simple_bus_reg): Node /soc/timer missing or empty reg/ranges property
DTC arch/arm/boot/dts/r8a7743-sk-rzg1m.dtb
arch/arm/boot/dts/r8a7743-sk-rzg1m.dtb: Warning (simple_bus_reg): Node /soc/thermal-zones missing or empty reg/ranges property
arch/arm/boot/dts/r8a7743-sk-rzg1m.dtb: Warning (simple_bus_reg): Node /soc/timer missing or empty reg/ranges property
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort root sub-nodes alphabetically to allow for easier maintenance
of this file.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable sound PIO support on carrier board.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables SGTL5000 audio codec on the carrier board.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The timer node does not have any register properties and thus shouldn't be
placed on the bus.
This problem is flagged by the compiler as follows:
$ make dtbs W=1
...
DTC arch/arm/boot/dts/r8a7792-wheat.dtb
arch/arm/boot/dts/r8a7792-blanche.dtb: Warning (simple_bus_reg): Node /soc/timer missing or empty reg/ranges property
arch/arm/boot/dts/r8a7792-wheat.dtb: Warning (simple_bus_reg): Node /soc/timer missing or empty reg/ranges property
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort root sub-nodes alphabetically to allow for easier maintenance
of this file.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
The timer node does not have any register properties and thus shouldn't be
placed on the bus.
This problem is flagged by the compiler as follows:
$ make dtbs W=1
...
arch/arm/boot/dts/r8a7745-iwg22d-sodimm.dtb: Warning (simple_bus_reg): Node /soc/timer missing or empty reg/ranges property
arch/arm/boot/dts/r8a7745-iwg22d-sodimm-dbhd-ca.dtb: Warning (simple_bus_reg): Node /soc/timer missing or empty reg/ranges property
DTC arch/arm/boot/dts/r8a7745-sk-rzg1e.dtb
arch/arm/boot/dts/r8a7745-sk-rzg1e.dtb: Warning (simple_bus_reg): Node /soc/timer missing or empty reg/ranges property
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort root sub-nodes alphabetically to allow for easier maintenance
of this file.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the definitions for pwm[0123456] to the SoC .dtsi.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch instantiates the thermal sensor module with thermal-zone
support.
This patch is based on the commit cac68a56e3
("ARM: dts: r8a7791: enable to use thermal-zone") by Kuninori Morimoto.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the definitions for pwm[0123456] to the SoC .dtsi.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When we added the regulator support in commit 90c5d7cdae ("ARM: dts:
sun8i: a711: Add regulator support"), we also dropped the PMIC's
compatible. Since it's not in the PMIC DTSI, unlike most other PMIC
DTSI, it obviously wasn't probing anymore.
Re-add it so that everything works again.
Fixes: 90c5d7cdae ("ARM: dts: sun8i: a711: Add regulator support")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch fixes a missing ethernet 0 alisas in the devicetree on the
Nanopi M1 Plus.
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The dwmac-sun8i hardware is present on the Nanopi M1.
It uses the internal PHY
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Convert all hex addresses in node unit addresses to lower case to fix warnings
like:
arch/arm/boot/dts/exynos5422-odroidhc1.dtb: Warning (simple_bus_reg):
Node /soc/nocp@10CA1000 simple-bus unit address format error, expected "10ca1000"
Conversion was done using sed:
$ sed -e 's/@\([a-zA-Z0-9_-]*\) {/@\L\1 {/' -i arch/arm/boot/dts/exynos*.dts*
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Improve the DTS files using lower case to fix the following dtc warnings:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>"
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" -e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +^C
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This is a follow up to commit 4c9847b737 ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The R-Car M2N hardware manual states that Tc = –40°C to +105°C. The
thermal sensor has an accuracy of ±5°C and there can be a temperature
difference of 1 or 2 degrees between Tjmax and the thermal sensor due
to the location of the latter.
This means that 95°C is a safer value to use.
Fixes: 57f9156bc6 ("ARM: dts: r8a7793: enable to use thermal-zone")
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The R-Car M2W hardware manual states that Tc = –40°C to +105°C. The
thermal sensor has an accuracy of ±5°C and there can be a temperature
difference of 1 or 2 degrees between Tjmax and the thermal sensor due
to the location of the latter.
This means that 95°C is a safer value to use.
Fixes: cac68a56e3 ("ARM: dts: r8a7791: enable to use thermal-zone")
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The R-Car H2 hardware manual states that Tc = –40°C to +105°C. The
thermal sensor has an accuracy of ±5°C and there can be a temperature
difference of 1 or 2 degrees between Tjmax and the thermal sensor due
to the location of the latter.
This means that 95°C is a safer value to use.
Fixes: a8b805f360 ("ARM: dts: r8a7790: enable to use thermal-zone")
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic r8a7743(RZ/G1M) part of the sound device node.
This patch is based on the r8a7791 sound work by Kuninori Morimoto.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Instantiate the two audio DMA controllers on the r8a7743 device tree.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the external audio clocks required by the sound driver.
Boards that provide audio clocks need to override the clock frequencies.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Three sets of overlapping changes, two in the packet scheduler
and one in the meson-gxl PHY driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the control register as the base for the clock nodes which are
missing them. This squashes some 22 warnings of the effect when built
with W=1.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Add the control register as the base for the clock nodes which are
missing them. This squashes the following warnings of the effect when built
with W=1:
arch/arm/boot/dts/keystone-k2e-evm.dtb: Warning (unit_address_vs_reg): Node /soc@0/clocks/clkusb1 has a reg or ranges property, but no unit name
arch/arm/boot/dts/keystone-k2e-evm.dtb: Warning (unit_address_vs_reg): Node /soc@0/clocks/clkhyperlink0 has a reg or ranges property, but no unit name
arch/arm/boot/dts/keystone-k2e-evm.dtb: Warning (unit_address_vs_reg): Node /soc@0/clocks/clkpcie1 has a reg or ranges property, but no unit name
arch/arm/boot/dts/keystone-k2e-evm.dtb: Warning (unit_address_vs_reg): Node /soc@0/clocks/clkxge has a reg or ranges property, but no unit name
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Add the control register as the base for the clock nodes which are
missing them. This squashes some 36 warnings of the effect when built
with W=1.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Add the control register as the base for the clock nodes which are
missing them. This squashes some 78 warnings of the effect when built
with W=1.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Add base address for GIC as unit address. This also squashes the
following warnings when built with W=1:
arch/arm/boot/dts/keystone-k2hk-evm.dtb: Warning (unit_address_vs_reg): Node /interrupt-controller has a reg or ranges property, but no unit name
arch/arm/boot/dts/keystone-k2l-evm.dtb: Warning (unit_address_vs_reg): Node /interrupt-controller has a reg or ranges property, but no unit name
arch/arm/boot/dts/keystone-k2e-evm.dtb: Warning (unit_address_vs_reg): Node /interrupt-controller has a reg or ranges property, but no unit name
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
skeleton.dtsi doesn't offer us any real benefits with most of the
parameters being overridden. So, just drop the same entirely and
introduce appropriate changes for chosen node and memory back to
our top level definition.
This also squashes the following warnings with W=1:
arch/arm/boot/dts/keystone-k2hk-evm.dtb: Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
arch/arm/boot/dts/keystone-k2l-evm.dtb: Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
arch/arm/boot/dts/keystone-k2e-evm.dtb: Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Provide a soc0 node and reference the same to simplify dts. This also
resolves the following warnings when built with W=1:
arch/arm/boot/dts/keystone-k2hk-evm.dtb: Warning (unit_address_vs_reg): Node /soc has a reg or ranges property, but no unit name
arch/arm/boot/dts/keystone-k2l-evm.dtb: Warning (unit_address_vs_reg): Node /soc has a reg or ranges property, but no unit name
arch/arm/boot/dts/keystone-k2e-evm.dtb: Warning (unit_address_vs_reg): Node /soc has a reg or ranges property, but no unit name
arch/arm/boot/dts/keystone-k2g-evm.dtb: Warning (unit_address_vs_reg): Node /soc has a reg or ranges property, but no unit name
arch/arm/boot/dts/keystone-k2g-ice.dtb: Warning (unit_address_vs_reg): Node /soc has a reg or ranges property, but no unit name
NOTE: Though we can reformat files by reducing 1 level of indent due to
the use of soc0 phandle, we omit that change to prevent un-necessary
churn in code base.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Standardize the licenses with SPDX license tag and standardize TI's
copyright statement to be consistently after file description.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" -e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +^C
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve as a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>"
This is a follow up to commit 4c9847b737 ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The ethernet phy of rk3066a-rayeager has a reset pin, it controlled by
GPIO1_D6, this pin should be pull down then pull up to reset the phy.
Add a reset-gpios property in phy0, make the phy can be reset when emac
power on.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This adds a basic device tree for the D-Link DNS-313
NAS enclosure. This device has a thermal sensor and a
fan so we add a thermal zone for the chassis in the
device tree based on information from the product.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These Gemini boards have Ethernet PHY on GPIO bit-banged
MDIO, clearly defined in the corresponding OpenWRT
ethernet patches since ages. Add them in accordance with
the OpenWRT patch so we can use them when we add ethernet
support.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull networking fixes from David Miller:
1) Clamp timeouts to INT_MAX in conntrack, from Jay Elliot.
2) Fix broken UAPI for BPF_PROG_TYPE_PERF_EVENT, from Hendrik
Brueckner.
3) Fix locking in ieee80211_sta_tear_down_BA_sessions, from Johannes
Berg.
4) Add missing barriers to ptr_ring, from Michael S. Tsirkin.
5) Don't advertise gigabit in sh_eth when not available, from Thomas
Petazzoni.
6) Check network namespace when delivering to netlink taps, from Kevin
Cernekee.
7) Kill a race in raw_sendmsg(), from Mohamed Ghannam.
8) Use correct address in TCP md5 lookups when replying to an incoming
segment, from Christoph Paasch.
9) Add schedule points to BPF map alloc/free, from Eric Dumazet.
10) Don't allow silly mtu values to be used in ipv4/ipv6 multicast, also
from Eric Dumazet.
11) Fix SKB leak in tipc, from Jon Maloy.
12) Disable MAC learning on OVS ports of mlxsw, from Yuval Mintz.
13) SKB leak fix in skB_complete_tx_timestamp(), from Willem de Bruijn.
14) Add some new qmi_wwan device IDs, from Daniele Palmas.
15) Fix static key imbalance in ingress qdisc, from Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
net: qcom/emac: Reduce timeout for mdio read/write
net: sched: fix static key imbalance in case of ingress/clsact_init error
net: sched: fix clsact init error path
ip_gre: fix wrong return value of erspan_rcv
net: usb: qmi_wwan: add Telit ME910 PID 0x1101 support
pkt_sched: Remove TC_RED_OFFLOADED from uapi
net: sched: Move to new offload indication in RED
net: sched: Add TCA_HW_OFFLOAD
net: aquantia: Increment driver version
net: aquantia: Fix typo in ethtool statistics names
net: aquantia: Update hw counters on hw init
net: aquantia: Improve link state and statistics check interval callback
net: aquantia: Fill in multicast counter in ndev stats from hardware
net: aquantia: Fill ndev stat couters from hardware
net: aquantia: Extend stat counters to 64bit values
net: aquantia: Fix hardware DMA stream overload on large MRRS
net: aquantia: Fix actual speed capabilities reporting
sock: free skb in skb_complete_tx_timestamp on error
s390/qeth: update takeover IPs after configuration change
s390/qeth: lock IP table while applying takeover changes
...
With the backlight phandle the driver can manage the backlight on/off in
sync with the panel enable/disable.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the backlight phandle the driver can manage the backlight on/off in
sync with the panel enable/disable.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the backlight phandle the driver can manage the backlight on/off in
sync with the panel enable/disable.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have
leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have
leading 0s
Converted using the following command:
$ find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec \
sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" \
-e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +^C
For simplicity, two sed expressions were used to solve each warnings
separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before
the the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve as a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format
error, expected "<lower>"
This is a follow up to commit 4c9847b737 ("dt-bindings: Remove leading
0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pin control information for the NAND flash interface.
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The board has a regular-sized HDMI connector, so enable the display
the pipeline and HDMI output for it.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A83T has 3 I2C controllers under the standard bus. There is one
more in the R_ block section. The pin functions for the 3 controllers
are on PH 0~6. I2C2 can also be used on pins PE14 and PE15, but these
pins can also mux the CSI (camera sensor interface) controller's
embedded I2C controller. The latter seems to be preferred in the
reference designs for I2C camera sensor access, freeing I2C2 for other
uses.
This patch adds device nodes for the three standard I2C controllers,
as well as pinmux settings for the PH pins. For I2C0 and I2C1, since
they only have one possible setting, just set them by default.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A83T has 3 I2S controllers. The first is multiplexed with the TDM
controller. The pins are generally connected to the codec side of the
AXP81x PMIC/codec/RTC chip. The second is free for other uses. The
third only supports output, and is connected internally to the HDMI
controller for HDMI audio output.
This patch adds device nodes for the controllers, and a default pinmux
setting for the second controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add nodes for the True Random Number Generator found in Samsung Exynos
5250+ SoCs.
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Fix that bananapi-r2 booting from SD-card would fail since incorrect
polarity is applied to the previous setup with GPIO_ACTIVE_HIGH.
Cc: stable@vger.kernel.org
Fixes: 0eed8d0976 ("arm: dts: mt7623: Add SD-card and EMMC to bananapi-r2")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Tested-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The current mmc related nodes should be falling back to MT2701
as the dt-binding defines and which has more appropriate setup
for MT7623.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The hifsys and ethsys needs the definition of the reset-cells
property. Fix this.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The ethsys binding misses the reset-cells, this patch
adds this property.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Use XAUI rather than XGMII for DSA link ports, as this is the interface
mode that the switches actually use. XAUI is the 4 lane bus with clock
per direction, whereas XGMII is a 32 bit bus with clock.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables the GPIO interrupt controller for the Meson8 SoCs.
Interrupt support on the GPIOs can be used by the MMC framework to
detect when an SD card is inserted/removed or by the input framework to
detect button presses.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add nodes for Pseudo Random Number Generator in dts files describing
Exynos5 chips.
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The newly added OMAP35xx Torpedo does not have a WiFi option, so
this patch moves the WL1283 binding and pin muxing to the
logicpd-torpedo-37xx-devkit since it's only applicable on that SOM
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the common baseboard info moved into its own file and the
common torpedo already in its own file, we can very easily
create a new devkit specific for the OMAP35xx.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Development kits consist of a SOM connected to a baseboard. Moving most
of the devkit files to baseboard allow us to re-use much of the contents in
preparation for using it on the OMAP35xx varation of the same kit.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the common baseboard info moved into its own file and the common SOM-LV
already in its own file, we can very easily create a new devkit specific
for the OMAP35xx.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Development kits consist of a SOM connected to a baseboard. Moving most
of the devkit files to baseboard allow us to re-use much of the contents in
preparation for using it on the OMAP35xx varation of the same kit.
Signed-off-by: Adam Ford <aford173@gmail.com>
[tony@atomide.com: updated to apply on recent gpmc range fixes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The audio DMA request for hdmi is crossbar 76 and we use sDMA
to handle the data transfer.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The metastability workaround causes Erratic errors [1]
on the HighSpeed USB PHY which can cause upto 2 seconds
delay in enumerating to a USB host while in Gadget mode.
Disable the Run/Stop metastability workaround to avoid this
ill effect. We are aware that this opens up the opportunity
for Run/Stop metastability, however this issue has never been
observed in TI releases so we think that Run/Stop metastability
is a lesser evil than the PHY Erratic errors. So disable it.
[1] USB controller trace during gadget enumeration
irq/90-dwc3-969 [000] d... 52.323145: dwc3_event: event
(00000901): Erratic Error [U0]
irq/90-dwc3-969 [000] d... 52.560646: dwc3_event: event
(00000901): Erratic Error [U0]
irq/90-dwc3-969 [000] d... 52.798144: dwc3_event: event
(00000901): Erratic Error [U0]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@linux/intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since U-Boot passes this information to the kernel, let's remove
the partition information from the device tree for
logicpd-torpedo-37xx-devkit and logicpd-som-lv-37xx-devkit
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add clkctrl nodes for DM816x SoC. These are going to be acting as
replacement for part of the existing clock data and the existing
clkctrl hooks under hwmod data.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add clkctrl nodes for DM814x SoC. These are going to be acting as
replacement for part of the existing clock data and the existing
clkctrl hooks under hwmod data.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add clkctrl nodes for AM43xx SoC. These are going to be acting as
replacement for part of the existing clock data and the existing
clkctrl hooks under hwmod data.
This patch also removes any obsolete clock nodes, and reroutes all users
for these to use the new clkctrl clocks instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add clkctrl nodes for AM33xx SoC. These are going to be acting as
replacement for part of the existing clock data and the existing
clkctrl hooks under hwmod data.
This patch also removes any obsolete clock nodes, and reroutes all users
for these to use the new clkctrl clocks instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add clkctrl nodes for DRA7 SoC. These are going to be acting as
replacement for part of the existing clock data and the existing
clkctrl hooks under hwmod data.
This patch also removes any obsolete clock nodes, and reroutes all users
for these to use the new clkctrl clocks instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add clkctrl nodes for OMAP5 SoC. These are going to be acting as
replacement for part of the existing clock data and the existing
clkctrl hooks under hwmod data.
This patch also removes any obsolete clock nodes, and reroutes all users
for these to use the new clkctrl clocks instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add clkctrl nodes for OMAP4 SoC. These are going to be acting as
replacement for part of the existing clock data and the existing
clkctrl hooks under hwmod data.
This patch also removes any obsolete clock nodes, and reroutes all users
for these to use the new clkctrl clocks instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add simple-bus compatibility and ranges properties to prcm node. This is
done in preparation of adding the support for clkctrl nodes.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add simple-bus compatibility and ranges properties to prcm node. This is
done in preparation of adding the support for clkctrl nodes.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add simple-bus compatibility and ranges properties to prcm node. This is
done in preparation of adding the support for clkctrl nodes.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add simple-bus compatibility and ranges properties to cm1, cm2 and prm
nodes. This is done in preparation of adding the support for clkctrl
nodes.
SPLIT: timer1 fck setup
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add simple-bus compatibility and ranges properties to cm1, cm2 and prm
nodes. This is done in preparation of adding the support for clkctrl
nodes.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add simple-bus compatibility and ranges properties to cm_core_aon, cm_core
and prm nodes. This is done in preparation of adding the support for
clkctrl nodes.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the functional clock definition for timers1/2. This is needed so that
the clock rate claculations continue to function properly once dm816x
transitions away from hwmod data and towards the clkctrl clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the functional clock definition for timers1/2. This is needed so that
the clock rate claculations continue to function properly once dm814x
transitions away from hwmod data and towards the clkctrl clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the functional clock definition for timer1. This is needed so that
the clock rate calculations continue to function properly once dra7
transitions away from hwmod data and towards the clkctrl clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the functional clock definition for timers1/2. This is needed so that
the clock rate calculations continue to function properly once am33xx
transitions away from hwmod data and towards the clkctrl clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the functional clock definition for timers1/2. This is needed so that
the clock rate calculations continue to function properly once am33xx
transitions away from hwmod data and towards the clkctrl clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the functional clock definition for timer1. This is needed so that
the clock rate calculations continue to function properly once omap4
transitions away from hwmod data and towards the clkctrl clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
