HV interrupts that use HSRR registers do not enter with MSR[RI] clear,
but their entry code is not recoverable vs NMI, due to shared use of
HSPRG1 as a scratch register to save r13.
This means that a system reset or machine check that hits in HSRR
interrupt entry can cause r13 to be silently corrupted.
Fix this by marking NMIs non-recoverable if they land in HV interrupt
ranges.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds emulation support for the following integer instructions:
* Multiply-Add High Doubleword (maddhd)
* Multiply-Add High Doubleword Unsigned (maddhdu)
* Multiply-Add Low Doubleword (maddld)
As suggested by Michael, this uses a raw .long for specifying the
instruction word when using inline assembly to retain compatibility
with older binutils.
Signed-off-by: Sandipan Das <sandipan@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that current_thread_info is located at the beginning of 'current'
task struct, CURRENT_THREAD_INFO macro is not really needed any more.
This patch replaces it by loads of the value at PACA_THREAD_INFO(r13).
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Add PACA_THREAD_INFO rather than using PACACURRENT]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that thread_info is similar to task_struct, its address is in r2
so CURRENT_THREAD_INFO() macro is useless. This patch removes it.
This patch also moves the 'tovirt(r2, r2)' down just before the
reactivation of MMU translation, so that we keep the physical address
of 'current' in r2 until then. It avoids a few calls to tophys().
At the same time, as the 'cpu' field is not anymore in thread_info,
TI_CPU is renamed TASK_CPU by this patch.
It also allows to get rid of a couple of
'#ifdef CONFIG_VIRT_CPU_ACCOUNTING_NATIVE' as ACCOUNT_CPU_USER_ENTRY()
and ACCOUNT_CPU_USER_EXIT() are empty when
CONFIG_VIRT_CPU_ACCOUNTING_NATIVE is not defined.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Fix a missed conversion of TI_CPU idle_6xx.S]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The table of pointers 'current_set' has been used for retrieving
the stack and current. They used to be thread_info pointers as
they were pointing to the stack and current was taken from the
'task' field of the thread_info.
Now, the pointers of 'current_set' table are now both pointers
to task_struct and pointers to thread_info.
As they are used to get current, and the stack pointer is
retrieved from current's stack field, this patch changes
their type to task_struct, and renames secondary_ti to
secondary_current.
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
thread_info is not anymore in the stack, so the entire stack
can now be used.
There is also no risk anymore of corrupting task_cpu(p) with a
stack overflow so the patch removes the test.
When doing this, an explicit test for NULL stack pointer is
needed in validate_sp() as it is not anymore implicitely covered
by the sizeof(thread_info) gap.
In the meantime, with the previous patch all pointers to the stacks
are not anymore pointers to thread_info so this patch changes them
to void*
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch activates CONFIG_THREAD_INFO_IN_TASK which
moves the thread_info into task_struct.
Moving thread_info into task_struct has the following advantages:
- It protects thread_info from corruption in the case of stack
overflows.
- Its address is harder to determine if stack addresses are leaked,
making a number of attacks more difficult.
This has the following consequences:
- thread_info is now located at the beginning of task_struct.
- The 'cpu' field is now in task_struct, and only exists when
CONFIG_SMP is active.
- thread_info doesn't have anymore the 'task' field.
This patch:
- Removes all recopy of thread_info struct when the stack changes.
- Changes the CURRENT_THREAD_INFO() macro to point to current.
- Selects CONFIG_THREAD_INFO_IN_TASK.
- Modifies raw_smp_processor_id() to get ->cpu from current without
including linux/sched.h to avoid circular inclusion and without
including asm/asm-offsets.h to avoid symbol names duplication
between ASM constants and C constants.
- Modifies klp_init_thread_info() to take a task_struct pointer
argument.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Add task_stack.h to livepatch.h to fix build fails]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Change current_pt_regs() to use task_stack_page() rather than
current_thread_info() so that it keeps working once we enable
THREAD_INFO_IN_TASK.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Split out of large patch]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When we enable THREAD_INFO_IN_TASK we will remove our definition of
current_thread_info(). Instead it will come from linux/thread_info.h
So switch processor.h to include the latter, so that it can continue
to find current_thread_info().
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Split out of larger patch]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently INIT_SP_LIMIT uses sizeof(init_thread_info), but that symbol
won't exist when we enable THREAD_INFO_IN_TASK. So just use the sizeof
the type which is the same value but will continue to work.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Split out of larger patch]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Update a few comments that talk about current_thread_info() in
preparation for THREAD_INFO_IN_TASK.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Split out of larger patch]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The purpose of the pointer given to call_do_softirq() and
call_do_irq() is to point the new stack. Currently that's the same
thing as the thread_info, but won't be with THREAD_INFO_IN_TASK.
So change the parameter to void* and rename it 'sp'.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Split out of larger patch]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When activating CONFIG_THREAD_INFO_IN_TASK, linux/sched.h includes
asm/current.h. This generates a circular dependency. To avoid that,
asm/processor.h shall not be included in mmu-hash.h.
In order to do that, this patch moves into a new header called
asm/task_size_64/32.h all the TASK_SIZE related constants, which can
then be included in mmu-hash.h directly.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Split out all the TASK_SIZE constants not just 64-bit ones]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch implements handling of STRICT_KERNEL_RWX with
large TLBs directly in the TLB miss handlers.
To do so, etext and sinittext are aligned on 512kB boundaries
and the miss handlers use 512kB pages instead of 8Mb pages for
addresses close to the boundaries.
It sets RO PP flags for addresses under sinittext.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Today, STRICT_KERNEL_RWX is based on the use of regular pages
to map kernel pages.
On Book3s 32, it has three consequences:
- Using pages instead of BAT for mapping kernel linear memory severely
impacts performance.
- Exec protection is not effective because no-execute cannot be set at
page level (except on 603 which doesn't have hash tables)
- Write protection is not effective because PP bits do not provide RO
mode for kernel-only pages (except on 603 which handles it in software
via PAGE_DIRTY)
On the 603+, we have:
- Independent IBAT and DBAT allowing limitation of exec parts.
- NX bit can be set in segment registers to forbit execution on memory
mapped by pages.
- RO mode on DBATs even for kernel-only blocks.
On the 601, there is nothing much we can do other than warn the user
about it, because:
- BATs are common to instructions and data.
- BAT do not provide RO mode for kernel-only blocks.
- segment registers don't have the NX bit.
In order to use IBAT for exec protection, this patch:
- Aligns _etext to BAT block sizes (128kb)
- Set NX bit in kernel segment register (Except on vmalloc area when
CONFIG_MODULES is selected)
- Maps kernel text with IBATs.
In order to use DBAT for exec protection, this patch:
- Aligns RW DATA to BAT block sizes (4M)
- Maps kernel RO area with write prohibited DBATs
- Maps remaining memory with remaining DBATs
Here is what we get with this patch on a 832x when activating
STRICT_KERNEL_RWX:
Symbols:
c0000000 T _stext
c0680000 R __start_rodata
c0680000 R _etext
c0800000 T __init_begin
c0800000 T _sinittext
~# cat /sys/kernel/debug/block_address_translation
---[ Instruction Block Address Translation ]---
0: 0xc0000000-0xc03fffff 0x00000000 Kernel EXEC coherent
1: 0xc0400000-0xc05fffff 0x00400000 Kernel EXEC coherent
2: 0xc0600000-0xc067ffff 0x00600000 Kernel EXEC coherent
3: -
4: -
5: -
6: -
7: -
---[ Data Block Address Translation ]---
0: 0xc0000000-0xc07fffff 0x00000000 Kernel RO coherent
1: 0xc0800000-0xc0ffffff 0x00800000 Kernel RW coherent
2: 0xc1000000-0xc1ffffff 0x01000000 Kernel RW coherent
3: 0xc2000000-0xc3ffffff 0x02000000 Kernel RW coherent
4: 0xc4000000-0xc7ffffff 0x04000000 Kernel RW coherent
5: 0xc8000000-0xcfffffff 0x08000000 Kernel RW coherent
6: 0xd0000000-0xdfffffff 0x10000000 Kernel RW coherent
7: -
~# cat /sys/kernel/debug/segment_registers
---[ User Segments ]---
0x00000000-0x0fffffff Kern key 1 User key 1 VSID 0xa085d0
0x10000000-0x1fffffff Kern key 1 User key 1 VSID 0xa086e1
0x20000000-0x2fffffff Kern key 1 User key 1 VSID 0xa087f2
0x30000000-0x3fffffff Kern key 1 User key 1 VSID 0xa08903
0x40000000-0x4fffffff Kern key 1 User key 1 VSID 0xa08a14
0x50000000-0x5fffffff Kern key 1 User key 1 VSID 0xa08b25
0x60000000-0x6fffffff Kern key 1 User key 1 VSID 0xa08c36
0x70000000-0x7fffffff Kern key 1 User key 1 VSID 0xa08d47
0x80000000-0x8fffffff Kern key 1 User key 1 VSID 0xa08e58
0x90000000-0x9fffffff Kern key 1 User key 1 VSID 0xa08f69
0xa0000000-0xafffffff Kern key 1 User key 1 VSID 0xa0907a
0xb0000000-0xbfffffff Kern key 1 User key 1 VSID 0xa0918b
---[ Kernel Segments ]---
0xc0000000-0xcfffffff Kern key 0 User key 1 No Exec VSID 0x000ccc
0xd0000000-0xdfffffff Kern key 0 User key 1 No Exec VSID 0x000ddd
0xe0000000-0xefffffff Kern key 0 User key 1 No Exec VSID 0x000eee
0xf0000000-0xffffffff Kern key 0 User key 1 No Exec VSID 0x000fff
Aligning _etext to 128kb allows to map up to 32Mb text with 8 IBATs:
16Mb + 8Mb + 4Mb + 2Mb + 1Mb + 512kb + 256kb + 128kb (+ 128kb) = 32Mb
(A 9th IBAT is unneeded as 32Mb would need only a single 32Mb block)
Aligning data to 4M allows to map up to 512Mb data with 8 DBATs:
16Mb + 8Mb + 4Mb + 4Mb + 32Mb + 64Mb + 128Mb + 256Mb = 512Mb
Because some processors only have 4 BATs and because some targets need
DBATs for mapping other areas, the following patch will allow to
modify _etext and data alignment.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
setibat() and clearibat() allows to manipulate IBATs independently
of DBATs.
update_bats() allows to update bats after init. This is done
with MMU off.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch defined CONFIG_PPC_PAGE_SHIFT in order
to be able to use PAGE_SHIFT value inside Kconfig.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a helper to know whether STRICT_KERNEL_RWX is enabled.
This is based on rodata_enabled flag which is defined only
when CONFIG_STRICT_KERNEL_RWX is selected.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch add an helper which wraps 'mtsrin' instruction
to write into segment registers.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds test cases for the addc[.] instruction.
Signed-off-by: Sandipan Das <sandipan@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
For pages without _PAGE_USER, PP field is 00
For pages with _PAGE_USER, PP field is 10 for RW and 11 for RO.
This patch sets _PAGE_USER to 0x002 and _PAGE_RW to 0x001
is order to simplify TLB handling by reducing amount of shifts.
The location of _PAGE_PRESENT and _PAGE_HASHPTE doesn't matter
as they are only SW related flags.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use SPRN_SPRG2 to store the current thread PGDIR and
avoid reading thread_struct.pgdir at every TLB miss.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When calling RTAS, the stack pointer is stored in SPRN_SPRG2
in order to be able to restore it in case of machine check in RTAS.
As machine check is not a perfomance critical path, this patch
frees SPRN_SPRG2 by using a field in thread struct instead.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is no reason to re-read each time the pointer at
location 0xf0 as it is fixed and known.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 24be85a23d ("powerpc/powernv: Clear PECE1 in LPCR via stop-api
only on Hotplug", 2017-07-21) added two calls to opal_slw_set_reg()
inside pnv_cpu_offline(), with the aim of changing the LPCR value in
the SLW image to disable wakeups from the decrementer while a CPU is
offline. However, pnv_cpu_offline() gets called each time a secondary
CPU thread is woken up to participate in running a KVM guest, that is,
not just when a CPU is offlined.
Since opal_slw_set_reg() is a very slow operation (with observed
execution times around 20 milliseconds), this means that an offline
secondary CPU can often be busy doing the opal_slw_set_reg() call
when the primary CPU wants to grab all the secondary threads so that
it can run a KVM guest. This leads to messages like "KVM: couldn't
grab CPU n" being printed and guest execution failing.
There is no need to reprogram the SLW image on every KVM guest entry
and exit. So that we do it only when a CPU is really transitioning
between online and offline, this moves the calls to
pnv_program_cpu_hotplug_lpcr() into pnv_smp_cpu_kill_self().
Fixes: 24be85a23d ("powerpc/powernv: Clear PECE1 in LPCR via stop-api only on Hotplug")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When updating page tables, we need to make sure we fill the page table
entry valid bits. We do this by or'ing in one of PGD/PUD/PMD_VAL_BITS.
The page table 'set' interfaces allow updating the raw value of page
table entries without setting the valid bits, so remove those
interfaces to avoid incorrect usage in future.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
[mpe: Reword commit message based on mailing list discussion]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds a debugfs interface to force scheduling a recovery event.
This can be used to recover a specific PE or schedule a "special" recovery
even that checks for errors at the PHB level.
To force a recovery of a normal PE, use:
echo '<#pe>:<#phb>' > /sys/kernel/debug/powerpc/eeh_force_recover
To force a scan for broken PHBs:
echo 'hwcheck' > /sys/kernel/debug/powerpc/eeh_force_recover
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently when we detect an error we automatically invoke the EEH recovery
handler. This can be annoying when debugging EEH problems, or when working
on EEH itself so this patch adds a debugfs knob that will prevent a
recovery event from being queued up when an issue is detected.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a helper to find the pci_controller structure based on the domain
number / phb id.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Adds a debugfs file that can be read to view the contents of the EEH
address cache. This is pretty similar to the existing
eeh_addr_cache_print() function, but that function is intended to debug
issues inside of the kernel since it's #ifdef`ed out by default, and writes
into the kernel log.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There's no need to the custom getter/setter functions so we should remove
them in favour of using the generic one. While we're here, change the type
of eeh_max_freeze to u32 and print the value in decimal rather than
hex because printing it in hex makes no sense.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit d4fde568a3 ("powerpc/64: Use optimized checksum routines on
little-endian") converted last powerpc user of GENERIC_CSUM.
This patch does a final cleanup dropping the Kconfig GENERIC_CSUM
option which is always 'n', and associated piece of code in
asm/checksum.h
Fixes: d4fde568a3 ("powerpc/64: Use optimized checksum routines on little-endian")
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch updates the kernel non-linear virtual map to 512TB when
we're built with 64K page size and are using the hash MMU. We allocate
one context for the vmalloc region and hence the max virtual area size
is limited by the context map size (512TB for 64K and 64TB for 4K page
size).
This patch fixes boot failures with large amounts of system RAM where
we need large vmalloc space to handle per cpu allocations.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Tested-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
This adds an "in_guest" parameter to machine_check_print_event_info()
so that we can avoid trying to translate guest NIP values into
symbolic form using the host kernel's symbol table.
Reviewed-by: Aravinda Prasad <aravinda@linux.vnet.ibm.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This makes the handling of machine check interrupts that occur inside
a guest simpler and more robust, with less done in assembler code and
in real mode.
Now, when a machine check occurs inside a guest, we always get the
machine check event struct and put a copy in the vcpu struct for the
vcpu where the machine check occurred. We no longer call
machine_check_queue_event() from kvmppc_realmode_mc_power7(), because
on POWER8, when a vcpu is running on an offline secondary thread and
we call machine_check_queue_event(), that calls irq_work_queue(),
which doesn't work because the CPU is offline, but instead triggers
the WARN_ON(lazy_irq_pending()) in pnv_smp_cpu_kill_self() (which
fires again and again because nothing clears the condition).
All that machine_check_queue_event() actually does is to cause the
event to be printed to the console. For a machine check occurring in
the guest, we now print the event in kvmppc_handle_exit_hv()
instead.
The assembly code at label machine_check_realmode now just calls C
code and then continues exiting the guest. We no longer either
synthesize a machine check for the guest in assembly code or return
to the guest without a machine check.
The code in kvmppc_handle_exit_hv() is extended to handle the case
where the guest is not FWNMI-capable. In that case we now always
synthesize a machine check interrupt for the guest. Previously, if
the host thinks it has recovered the machine check fully, it would
return to the guest without any notification that the machine check
had occurred. If the machine check was caused by some action of the
guest (such as creating duplicate SLB entries), it is much better to
tell the guest that it has caused a problem. Therefore we now always
generate a machine check interrupt for guests that are not
FWNMI-capable.
Reviewed-by: Aravinda Prasad <aravinda@linux.vnet.ibm.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is no need to provide anything but get_arch_dma_ops to
<linux/dma-mapping.h>. More the remaining declarations to <asm/iommu.h>
and drop all the includes.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is no good reason for this helper, just opencode it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Just fold the calculation into __phys_to_dma/__dma_to_phys as those are
the only places that should know about it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that we've switched all the powerpc nommu and swiotlb methods to
use the generic dma_direct_* calls we can remove these ops vectors
entirely and rely on the common direct mapping bypass that avoids
indirect function calls entirely. This also allows to remove a whole
lot of boilerplate code related to setting up these operations.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Switch the streaming DMA mapping and ownership transfer methods to the
functionally identical dma_direct_ versions. Factor the cache
maintainance helpers into the form expected by the common code for that.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The generic code allows a few nice things such as node local allocations
and dipping into the CMA area. The lookup of the right zone for a given
dma mask works a little different, but the results should be the same.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This function is largely identical to the generic version used
everywhere else. Replace it with the generic version.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This function is identical to the generic dma_direct_get_required_mask,
except that the generic version also takes the bus_dma_mask account,
which could lead to incorrect results in the powerpc version.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The coherent cache version of this function already is functionally
identicall to the default version, and by defining the
arch_dma_coherent_to_pfn hook the same is ture for the noncoherent
version as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Instead of letting the architecture supply all of dma_set_mask just
give it an additional hook selected by Kconfig.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We need to compare the last byte in the dma range and not the one after it
for the bus_dma_mask, just like we do for the regular dma_mask. Fix this
cleanly by merging the two comparisms into one.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
