Nothing in it can raise an error.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Clearly a right-shift was meant. Effectively doesn't make a difference,
as add_len is hard-coded to 8 and the high byte will be zero no matter
which way you shift. But I hate leaving bad examples for others to
copy.
Found by coverity.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch correctly handles match_int() errors in FILEIO + PSCSI
backend parameter parsing, which can potentially fail due to a
memory allocation failure or invalid argument.
Found by coverity.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Old code in iscsi_parse_pr_out_transport_id() was obviously buggy
and effectively ignored the high byte.
Found by coverity.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Coverity complained that lun_cg has been dereferenced in all paths
leading to NULL check. It didn't mention that only a single path could
lead there and the code can be simplified even further.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a memory leak on error in target_fabric_make_mappedlun(),
where se_lun_acl memory does not get released on exit.
Found by coverity.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Each case of match_strdup could leak memory if the same argument was
present before. I am not too concerned, as it would require a
non-sensical combination like "target_lun=foo target_lun=bar", done
with root privileges and even then leak just a few bytes per instance.
But arg_p is different, as it will always leak memory. Let's plug that
one. And while at it, replace some &args[0] with args.
Found by coverity.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
last_intr_fail_name is a fixed-size array and could theoretically
overflow. In reality intrname->value doesn't seem to depend on
untrusted input or be anywhere near 224 characters, so the overflow is
pretty theoretical. But strlcpy is cheap enough.
Found by coverity.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Found by coverity. At this point sock is non-NULL, so the check
to unnecessary.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch drops the now duplicate + unnecessary check for -ENODEV from
iscsi_transport->iscsit_accept_np() for jumping to out:, or immediately
returning 1 in __iscsi_target_login_thread() code.
Since commit 81a9c5e72b the jump to out: and returning 1 have the same
effect, and end up hitting the ISCSI_NP_THREAD_SHUTDOWN check regardless
at the top of __iscsi_target_login_thread() during next loop iteration.
So that said, it's safe to go ahead and remove this duplicate check.
Reported-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The return statement cannot be reached without either recovery or dump
being set to 1. Therefore the condition always evaluates to true and
recovery and dump are useless variables.
Found by Coverity.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Found by coverity. InitiatorName and InitiatorAlias are static arrays
and therefore always non-NULL. At some point in the past they may have
been dynamically allocated, but for current code the condition is
useless. If the intent was to check InitiatorName[0] instead, I cannot
find a use for that either. Let's get rid of it.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Last user of buf was removed with c6037cc546. While at it,
free_cpumask_var() handles a NULL argument just fine, so remove the
conditionals.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Clearly the file was meant to contain an include guard, but it was
missing the #define part.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The use of "rcu_assign_pointer()" is NULLing out the pointer.
According to RCU_INIT_POINTER()'s block comment:
"1. This use of RCU_INIT_POINTER() is NULLing out the pointer"
it is better to use it instead of rcu_assign_pointer() because it has a
smaller overhead.
The following Coccinelle semantic patch was used:
@@
@@
- rcu_assign_pointer
+ RCU_INIT_POINTER
(..., NULL)
Signed-off-by: Andreea-Cristina Bernat <bernat.ada@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch removes the null test on lun_cg. lun_cg is initialized
at the beginning of the function to &lun->lun_group. Since lun_cg is
dereferenced prior to the null test, it must be a valid pointer.
The following Coccinelle script is used for detecting the change:
@r@
expression e,f;
identifier g,y;
statement S1,S2;
@@
*e = &f->g
<+...
f->y
...+>
*if (e != NULL || ...)
S1 else S2
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch set consists of the usual driver updates (ufs, storvsc, pm8001
hpsa). It also has removal of the user space target driver code (everyone is
using LIO now), a partial PCI MSI-X update, more multi-queue updates,
conversion to 64 bit LUNs (so we could theoretically cope with any LUN
returned by a device) and placeholder support for the ZBC device type (Shingle
drives), plus an assortment of minor updates and bug fixes.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJT4mS9AAoJEDeqqVYsXL0Mq34H/2AeXiM8GEVO3PIsBtF3TFZ9
poJvAyb8t//+VwAIVLHU9wrssIrIcyvNQmNHH/InGt5rOaXwGQRsnEc73bBtot4b
aC1t+hAnp2Ddvu6phmyUg7iY2GmQhAoZmeaj7krGIu2XgtLGiPg26eSsgk4Yv/U9
cuULEuOc/UnTj3w5VK8SvpyXMybVF6oQhSrS1slOglfFwPTlTI/NHU9xo7Wc3qHT
VifHXNphIvye5EH8zwtKX5p8qCrFW0pevJwyfPz7Hp2CTA9XYKx3SoeOh+n9F9ez
udBBggg7Vb1tb4mPKUoZ78UrtCVdFSCmesBU/RJe7cIh8daKaO5MVr3WPSx2JhM=
=yGai
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This patch set consists of the usual driver updates (ufs, storvsc,
pm8001 hpsa). It also has removal of the user space target driver
code (everyone is using LIO now), a partial PCI MSI-X update, more
multi-queue updates, conversion to 64 bit LUNs (so we could
theoretically cope with any LUN returned by a device) and placeholder
support for the ZBC device type (Shingle drives), plus an assortment
of minor updates and bug fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (143 commits)
scsi: do not issue SCSI RSOC command to Promise Vtrak E610f
vmw_pvscsi: Use pci_enable_msix_exact() instead of pci_enable_msix()
pm8001: Fix invalid return when request_irq() failed
lpfc: Remove superfluous call to pci_disable_msix()
isci: Use pci_enable_msix_exact() instead of pci_enable_msix()
bfa: Use pci_enable_msix_exact() instead of pci_enable_msix()
bfa: Cleanup bfad_setup_intr() function
bfa: Do not call pci_enable_msix() after it failed once
fnic: Use pci_enable_msix_exact() instead of pci_enable_msix()
scsi: use short driver name for per-driver cmd slab caches
scsi_debug: support scsi-mq, queues and locks
Drivers: add blist flags
scsi: ufs: fix endianness sparse warnings
scsi: ufs: make undeclared functions static
bnx2i: Update driver version to 2.7.10.1
pm8001: fix a memory leak in nvmd_resp
pm8001: fix update_flash
pm8001: fix a memory leak in flash_update
pm8001: Cleaning up uninitialized variables
pm8001: Fix to remove null pointer checks that could never happen
...
Pull percpu updates from Tejun Heo:
- Major reorganization of percpu header files which I think makes
things a lot more readable and logical than before.
- percpu-refcount is updated so that it requires explicit destruction
and can be reinitialized if necessary. This was pulled into the
block tree to replace the custom percpu refcnting implemented in
blk-mq.
- In the process, percpu and percpu-refcount got cleaned up a bit
* 'for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (21 commits)
percpu-refcount: implement percpu_ref_reinit() and percpu_ref_is_zero()
percpu-refcount: require percpu_ref to be exited explicitly
percpu-refcount: use unsigned long for pcpu_count pointer
percpu-refcount: add helpers for ->percpu_count accesses
percpu-refcount: one bit is enough for REF_STATUS
percpu-refcount, aio: use percpu_ref_cancel_init() in ioctx_alloc()
workqueue: stronger test in process_one_work()
workqueue: clear POOL_DISASSOCIATED in rebind_workers()
percpu: Use ALIGN macro instead of hand coding alignment calculation
percpu: invoke __verify_pcpu_ptr() from the generic part of accessors and operations
percpu: preffity percpu header files
percpu: use raw_cpu_*() to define __this_cpu_*()
percpu: reorder macros in percpu header files
percpu: move {raw|this}_cpu_*() definitions to include/linux/percpu-defs.h
percpu: move generic {raw|this}_cpu_*_N() definitions to include/asm-generic/percpu.h
percpu: only allow sized arch overrides for {raw|this}_cpu_*() ops
percpu: reorganize include/linux/percpu-defs.h
percpu: move accessors from include/linux/percpu.h to percpu-defs.h
percpu: include/asm-generic/percpu.h should contain only arch-overridable parts
percpu: introduce arch_raw_cpu_ptr()
...
The SCSI standard defines 64-bit values for LUNs, and large arrays
employing large or hierarchical LUN numbers become more and more
common.
So update the linux SCSI stack to use 64-bit LUN numbers.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Currently, a percpu_ref undoes percpu_ref_init() automatically by
freeing the allocated percpu area when the percpu_ref is killed.
While seemingly convenient, this has the following niggles.
* It's impossible to re-init a released reference counter without
going through re-allocation.
* In the similar vein, it's impossible to initialize a percpu_ref
count with static percpu variables.
* We need and have an explicit destructor anyway for failure paths -
percpu_ref_cancel_init().
This patch removes the automatic percpu counter freeing in
percpu_ref_kill_rcu() and repurposes percpu_ref_cancel_init() into a
generic destructor now named percpu_ref_exit(). percpu_ref_destroy()
is considered but it gets confusing with percpu_ref_kill() while
"exit" clearly indicates that it's the counterpart of
percpu_ref_init().
All percpu_ref_cancel_init() users are updated to invoke
percpu_ref_exit() instead and explicit percpu_ref_exit() calls are
added to the destruction path of all percpu_ref users.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Benjamin LaHaise <bcrl@kvack.org>
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: Nicholas A. Bellinger <nab@linux-iscsi.org>
Cc: Li Zefan <lizefan@huawei.com>
On uniprocessor preemptible kernel, target core deadlocks on unload. The
following events happen:
* iscsit_del_np is called
* it calls send_sig(SIGINT, np->np_thread, 1);
* the scheduler switches to the np_thread
* the np_thread is woken up, it sees that kthread_should_stop() returns
false, so it doesn't terminate
* the np_thread clears signals with flush_signals(current); and goes back
to sleep in iscsit_accept_np
* the scheduler switches back to iscsit_del_np
* iscsit_del_np calls kthread_stop(np->np_thread);
* the np_thread is waiting in iscsit_accept_np and it doesn't respond to
kthread_stop
The deadlock could be resolved if the administrator sends SIGINT signal to
the np_thread with killall -INT iscsi_np
The reproducible deadlock was introduced in commit
db6077fd0b, but the thread-stopping code was
racy even before.
This patch fixes the problem. Using kthread_should_stop to stop the
np_thread is unreliable, so we test np_thread_state instead. If
np_thread_state equals ISCSI_NP_THREAD_SHUTDOWN, the thread exits.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes iscsit_check_dataout_hdr() to dump the incoming
Data-Out payload when the received ITT is not associated with a
WRITE, instead of calling iscsit_reject_cmd() for the non WRITE
ITT descriptor.
This addresses a bug where an initiator sending an Data-Out for
an ITT associated with a READ would end up generating a reject
for the READ, eventually resulting in list corruption.
Reported-by: Santosh Kulkarni <santosh.kulkarni@calsoftinc.com>
Reported-by: Arshad Hussain <arshad.hussain@calsoftinc.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a tcm_loop_cmd descriptor memory leak in the
tcm_loop_submission_work() error path, and would result in
warnings about leaked tcm_loop_cmd_cache objects at module
unload time.
Go ahead and invoke kmem_cache_free() to release tl_cmd back to
tcm_loop_cmd_cache before calling sc->scsi_done().
Reported-by: Sebastian Herbszt <herbszt@gmx.de>
Tested-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a explicit memset to the login response PDU
exception path in iscsit_tx_login_rsp().
This addresses a regression bug introduced in commit baa4d64b
where the initiator would end up not receiving the login
response and associated status class + detail, before closing
the login connection.
Reported-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr>
Tested-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a left-over se_lun->lun_sep pointer OOPs when one
of the /sys/kernel/config/target/$FABRIC/$WWPN/$TPGT/lun/$LUN/alua*
attributes is accessed after the $DEVICE symlink has been removed.
To address this bug, go ahead and clear se_lun->lun_sep memory in
core_dev_unexport(), so that the existing checks for show/store
ALUA attributes in target_core_fabric_configfs.c work as expected.
Reported-by: Sebastian Herbszt <herbszt@gmx.de>
Tested-by: Sebastian Herbszt <herbszt@gmx.de>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a check in chap_server_compute_md5() to enforce a
1024 byte maximum for the CHAP_C key value following the requirement
in RFC-3720 Section 11.1.4:
"..., C and R are large-binary-values and their binary length (not
the length of the character string that represents them in encoded
form) MUST not exceed 1024 bytes."
Reported-by: rahul.rane <rahul.rane@calsoftinc.com>
Tested-by: rahul.rane <rahul.rane@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts chap_server_compute_md5() from simple_strtoul() to
kstrtoul usage().
This addresses the case where a empty 'CHAP_I=' key value received during
mutual authentication would be converted to a '0' by simple_strtoul(),
instead of failing the login attempt.
Reported-by: Tejas Vaykole <tejas.vaykole@calsoftinc.com>
Tested-by: Tejas Vaykole <tejas.vaykole@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- Add support for T10 PI pass-through between vhost-scsi +
virtio-scsi (MST + Paolo + MKP + nab)
- Add support for T10 PI in qla2xxx target mode (Quinn + MKP + hch +
nab, merged through scsi.git)
- Add support for percpu-ida pre-allocation in qla2xxx target code
(Quinn + nab)
- A number of iser-target fixes related to hardening the network
portal shutdown path (Sagi + Slava)
- Fix response length residual handling for a number of control CDBs
(Roland + Christophe V.)
- Various iscsi RFC conformance fixes in the CHAP authentication path
(Tejas and Calsoft folks + nab)
- Return TASK_SET_FULL status for tcm_fc(FCoE) DataIn + Response
failures (Vasu + Jun + nab)
- Fix long-standing ABORT_TASK + session reset hang (nab)
- Convert iser-initiator + iser-target to include T10 bytes into EDTL
(Sagi + Or + MKP + Mike Christie)
- Fix NULL pointer dereference regression related to XCOPY introduced
in v3.15 + CC'ed to v3.12.y (nab)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (34 commits)
target: Fix NULL pointer dereference for XCOPY in target_put_sess_cmd
vhost-scsi: Include prot_bytes into expected data transfer length
TARGET/sbc,loopback: Adjust command data length in case pi exists on the wire
libiscsi, iser: Adjust data_length to include protection information
scsi_cmnd: Introduce scsi_transfer_length helper
target: Report correct response length for some commands
target/sbc: Check that the LBA and number of blocks are correct in VERIFY
target/sbc: Remove sbc_check_valid_sectors()
Target/iscsi: Fix sendtargets response pdu for iser transport
Target/iser: Fix a wrong dereference in case discovery session is over iser
iscsi-target: Fix ABORT_TASK + connection reset iscsi_queue_req memory leak
target: Use complete_all for se_cmd->t_transport_stop_comp
target: Set CMD_T_ACTIVE bit for Task Management Requests
target: cleanup some boolean tests
target/spc: Simplify INQUIRY EVPD=0x80
tcm_fc: Generate TASK_SET_FULL status for response failures
tcm_fc: Generate TASK_SET_FULL status for DataIN failures
iscsi-target: Reject mutual authentication with reflected CHAP_C
iscsi-target: Remove no-op from iscsit_tpg_del_portal_group
iscsi-target: Fix CHAP_A parameter list handling
...
This patch fixes a NULL pointer dereference regression bug that was
introduced with:
commit 1e1110c43b
Author: Mikulas Patocka <mpatocka@redhat.com>
Date: Sat May 17 06:49:22 2014 -0400
target: fix memory leak on XCOPY
Now that target_put_sess_cmd() -> kref_put_spinlock_irqsave() is
called with a valid se_cmd->cmd_kref, a NULL pointer dereference
is triggered because the XCOPY passthrough commands don't have
an associated se_session pointer.
To address this bug, go ahead and checking for a NULL se_sess pointer
within target_put_sess_cmd(), and call se_cmd->se_tfo->release_cmd()
to release the XCOPY's xcopy_pt_cmd memory.
Reported-by: Thomas Glanzmann <thomas@glanzmann.de>
Cc: Thomas Glanzmann <thomas@glanzmann.de>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org # 3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In various areas of the code, it is assumed that
se_cmd->data_length describes pure data. In case
that protection information exists over the wire
(protect bits is are on) the target core re-calculates
the data length from the CDB and the backed device
block size (instead of each transport peeking in the cdb).
Modify loopback device to include protection information
in the transferred data length (like other scsi transports).
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: stable@vger.kernel.org # 3.15+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When an initiator sends an allocation length bigger than what its
command consumes, the target should only return the actual response data
and set the residual length to the unused part of the allocation length.
Add a helper function that command handlers (INQUIRY, READ CAPACITY,
etc) can use to do this correctly, and use this code to get the correct
residual for commands that don't use the full initiator allocation in the
handlers for READ CAPACITY, READ CAPACITY(16), INQUIRY, MODE SENSE and
REPORT LUNS.
This addresses a handful of failures as reported by Christophe with
the Windows Certification Kit:
http://permalink.gmane.org/gmane.linux.scsi.target.devel/6515
Signed-off-by: Roland Dreier <roland@purestorage.com>
Tested-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch extracts LBA + sectors for VERIFY, and adds a goto check_lba
to perform the end-of-device checking.
(Update patch to drop lba_check usage - nab)
Signed-off-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
A similar check is performed at the end of sbc_parse_cdb() and is now
enforced if the SYNCHRONIZE CACHE command's backend supports
->execute_sync_cache().
(Add check_lba goto to avoid *_max_sectors checks - nab)
Signed-off-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In case the transport is iser we should not include the
iscsi target info in the sendtargets text response pdu.
This causes sendtargets response to include the target
info twice.
Modify iscsit_build_sendtargets_response to filter
transport types that don't match.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reported-by: Slava Shwartsman <valyushash@gmail.com>
Cc: stable@vger.kernel.org # 3.11+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull block layer fixes from Jens Axboe:
"Final small batch of fixes to be included before -rc1. Some general
cleanups in here as well, but some of the blk-mq fixes we need for the
NVMe conversion and/or scsi-mq. The pull request contains:
- Support for not merging across a specified "chunk size", if set by
the driver. Some NVMe devices perform poorly for IO that crosses
such a chunk, so we need to support it generically as part of
request merging avoid having to do complicated split logic. From
me.
- Bump max tag depth to 10Ki tags. Some scsi devices have a huge
shared tag space. Before we failed with EINVAL if a too large tag
depth was specified, now we truncate it and pass back the actual
value. From me.
- Various blk-mq rq init fixes from me and others.
- A fix for enter on a dying queue for blk-mq from Keith. This is
needed to prevent oopsing on hot device removal.
- Fixup for blk-mq timer addition from Ming Lei.
- Small round of performance fixes for mtip32xx from Sam Bradshaw.
- Minor stack leak fix from Rickard Strandqvist.
- Two __init annotations from Fabian Frederick"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: add __init to blkcg_policy_register
block: add __init to elv_register
block: ensure that bio_add_page() always accepts a page for an empty bio
blk-mq: add timer in blk_mq_start_request
blk-mq: always initialize request->start_time
block: blk-exec.c: Cleaning up local variable address returnd
mtip32xx: minor performance enhancements
blk-mq: ->timeout should be cleared in blk_mq_rq_ctx_init()
blk-mq: don't allow queue entering for a dying queue
blk-mq: bump max tag depth to 10K tags
block: add blk_rq_set_block_pc()
block: add notion of a chunk size for request merging
This patch fixes a iscsi_queue_req memory leak when ABORT_TASK response
has been queued by TFO->queue_tm_rsp() -> lio_queue_tm_rsp() after a
long standing I/O completes, but the connection has already reset and
waiting for cleanup to complete in iscsit_release_commands_from_conn()
-> transport_generic_free_cmd() -> transport_wait_for_tasks() code.
It moves iscsit_free_queue_reqs_for_conn() after the per-connection command
list has been released, so that the associated se_cmd tag can be completed +
released by target-core before freeing any remaining iscsi_queue_req memory
for the connection generated by lio_queue_tm_rsp().
Cc: Thomas Glanzmann <thomas@glanzmann.de>
Cc: Charalampos Pournaris <charpour@gmail.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug where multiple waiters on ->t_transport_stop_comp
occurs due to a concurrent ABORT_TASK and session reset both invoking
transport_wait_for_tasks(), while waiting for the associated se_cmd
descriptor backend processing to complete.
For this case, complete_all() should be invoked in order to wake up
both waiters in core_tmr_abort_task() + transport_generic_free_cmd()
process contexts.
Cc: Thomas Glanzmann <thomas@glanzmann.de>
Cc: Charalampos Pournaris <charpour@gmail.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug where se_cmd descriptors associated with a
Task Management Request (TMR) where not setting CMD_T_ACTIVE before
being dispatched into target_tmr_work() process context.
This is required in order for transport_generic_free_cmd() ->
transport_wait_for_tasks() to wait on se_cmd->t_transport_stop_comp
if a session reset event occurs while an ABORT_TASK is outstanding
waiting for another I/O to complete.
Cc: Thomas Glanzmann <thomas@glanzmann.de>
Cc: Charalampos Pournaris <charpour@gmail.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that 3.15 is released, this merges the 'next' branch into 'master',
bringing us to the normal situation where my 'master' branch is the
merge window.
* accumulated work in next: (6809 commits)
ufs: sb mutex merge + mutex_destroy
powerpc: update comments for generic idle conversion
cris: update comments for generic idle conversion
idle: remove cpu_idle() forward declarations
nbd: zero from and len fields in NBD_CMD_DISCONNECT.
mm: convert some level-less printks to pr_*
MAINTAINERS: adi-buildroot-devel is moderated
MAINTAINERS: add linux-api for review of API/ABI changes
mm/kmemleak-test.c: use pr_fmt for logging
fs/dlm/debug_fs.c: replace seq_printf by seq_puts
fs/dlm/lockspace.c: convert simple_str to kstr
fs/dlm/config.c: convert simple_str to kstr
mm: mark remap_file_pages() syscall as deprecated
mm: memcontrol: remove unnecessary memcg argument from soft limit functions
mm: memcontrol: clean up memcg zoneinfo lookup
mm/memblock.c: call kmemleak directly from memblock_(alloc|free)
mm/mempool.c: update the kmemleak stack trace for mempool allocations
lib/radix-tree.c: update the kmemleak stack trace for radix tree allocations
mm: introduce kmemleak_update_trace()
mm/kmemleak.c: use %u to print ->checksum
...
Convert "x == true" to "x" and "x == false" to "!x".
Signed-off-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes ft_queue_status() to set SAM_STAT_TASK_SET_FULL
status upon lport->tt.seq_send( failure, and return -EAGAIN to notify
target-core to attempt to requeue the response.
It also does the same for a fc_frame_alloc() failures, in order to
signal the initiator that it should try to reduce it's current
queue_depth, to lower the number of outstanding I/Os on the wire.
Reported-by: Vasu Dev <vasu.dev@linux.intel.com>
Reviewed-by: Vasu Dev <vasu.dev@linux.intel.com>
Cc: Jun Wu <jwu@stormojo.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes ft_queue_data_in() to set SAM_STAT_TASK_SET_FULL
status upon a lport->tt.seq_send() failure, where it will now stop
sending subsequent DataIN, and immediately attempt to send the
response with exception status.
Sending a response with SAM_STAT_TASK_SET_FULL status is useful in
order to signal the initiator that it should try to reduce it's
current queue_depth, to lower the number of outstanding I/Os on
the wire.
Also, add a check to skip sending DataIN if TASK_SET_FULL status
has already been set due to a response lport->tt.seq_send()
failure, that has asked target-core to requeue a response.
Reported-by: Vasu Dev <vasu.dev@linux.intel.com>
Reviewed-by: Vasu Dev <vasu.dev@linux.intel.com>
Cc: Jun Wu <jwu@stormojo.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
With the optimizations around not clearing the full request at alloc
time, we are leaving some of the needed init for REQ_TYPE_BLOCK_PC
up to the user allocating the request.
Add a blk_rq_set_block_pc() that sets the command type to
REQ_TYPE_BLOCK_PC, and properly initializes the members associated
with this type of request. Update callers to use this function instead
of manipulating rq->cmd_type directly.
Includes fixes from Christoph Hellwig <hch@lst.de> for my half-assed
attempt.
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch fixes a OOPs where an attempt to write to the per-device
alua_access_state configfs attribute at:
/sys/kernel/config/target/core/$HBA/$DEV/alua/$TG_PT_GP/alua_access_state
results in an NULL pointer dereference when the backend device has not
yet been configured.
This patch adds an explicit check for DF_CONFIGURED, and fails with
-ENODEV to avoid this case.
Reported-by: Chris Boot <crb@tiger-computing.co.uk>
Reported-by: Philip Gaw <pgaw@darktech.org.uk>
Cc: Chris Boot <crb@tiger-computing.co.uk>
Cc: Philip Gaw <pgaw@darktech.org.uk>
Cc: stable@vger.kernel.org # 3.8+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch allows READ_CAPACITY + SAI_READ_CAPACITY_16 opcode
processing to occur while the associated ALUA group is in Standby
access state.
This is required to avoid host side LUN probe failures during the
initial scan if an ALUA group has already implicitly changed into
Standby access state.
This addresses a bug reported by Chris + Philip using dm-multipath
+ ESX hosts configured with ALUA multipath.
Reported-by: Chris Boot <crb@tiger-computing.co.uk>
Reported-by: Philip Gaw <pgaw@darktech.org.uk>
Cc: Chris Boot <crb@tiger-computing.co.uk>
Cc: Philip Gaw <pgaw@darktech.org.uk>
Cc: Hannes Reinecke <hare@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds an explicit check in chap_server_compute_md5() to ensure
the CHAP_C value received from the initiator during mutual authentication
does not match the original CHAP_C provided by the target.
This is in line with RFC-3720, section 8.2.1:
Originators MUST NOT reuse the CHAP challenge sent by the Responder
for the other direction of a bidirectional authentication.
Responders MUST check for this condition and close the iSCSI TCP
connection if it occurs.
Reported-by: Tejas Vaykole <tejas.vaykole@calsoftinc.com>
Cc: stable@vger.kernel.org # 3.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch removes a no-op iscsit_clear_tpg_np_login_threads() call
in iscsit_tpg_del_portal_group(), which is unnecessary because
iscsit_tpg_del_portal_group() can only ever be removed from configfs
once all of the child network portals have been released.
Also, go ahed and make iscsit_clear_tpg_np_login_threads() declared
as static.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The target is failing to handle list of CHAP_A key-value pair form
initiator.The target is expecting CHAP_A=5 always. In other cases,
where initiator sends list (for example) CHAP_A=6,5 target is failing
the security negotiation. Which is incorrect.
This patch handles the case (RFC 3720 section 11.1.4).
where in the initiator may send list of CHAP_A values and target replies
with appropriate CHAP_A value in response
(Drop whitespaces + rename to chap_check_algorithm + save original
pointer + add explicit check for CHAP_A key - nab)
Signed-off-by: Tejas Vaykole <tejas.vaykole@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If the message "Unable to allocate…" pops up, it's useful to know
whether the problem is that the system is genuinely out of memory, or
that some bug has led to a crazy allocation length.
In particular this helped debug a corruption of login headers in
iscsi_login_non_zero_tsih_s1().
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
