Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm/boot/dts -type -f -name '*.dts*'
Dropped changes to ARM, Ltd. boards LED nodes and manually fixed up some
occurrences of uppercase hex.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Each serial port which supports HW flow-control should have 2 Pinctrl
groups. One for when HW flow-control is in progress, where the IP
will take over controlling the lines and another group which enables
the lines to be toggled using GPIO mechanisms.
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the pinctrl config for the spidf out
pins used by the sasg codec IP.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
This patch adds the pinctrl config for the i2s_in pins
used by the uniperif reader IP.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
This patch adds the pinctrl config for the i2s_out pins
used by the uniperif player IP.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
This patch allows to use second parameter to the gpio
specifier, which is used to specify whether the gpio is
active high or low.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
On 96board, we can't reuse rgmii1-mdio as the pin pio1 3
( mdint ) is dedicated for user led green 1. So create
rgmii1_mdio_1 for 96board on which only mdio and mdc pins
are useful.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Add missing pin muxing for I2C2 alternate 2. This
i2c2 pin muxing is dedicated for 96board high speed
expansion connector.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
[Lee: Correct spacing between nodes]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
This patch adds the RMII pinctrl support for the Synopsys
MAC on STiH407 SoCs.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This patch adds the pinconfig for IRB TX and IRB UHF.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This patch adds the missing SD pinctrl config
for mmc/sd controller 0. This is required to enable the
B2144A daughter board that exposes this controller as a sd
slot.
Signed-off-by: Nebil BEN MEFTEH <nebil.ben-mefteh@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This patch adds the pin config for systrace for
STiH407 family silicon.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This patch adds NAND flash support controller pin configuration
for STiH407 family silicon.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This patch adds the pin configuration for the NOR flash controller.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Add missing serial 3 pinctrl config. This can be used
on b2206 HVK, where it defaults to PIO31[3] & PIO31[4],
alternate 1.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Carmelo Amoroso <carmelo.amoroso@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This patch adds the spi pinctrl configurations for all SPI
controllers, and also the alternate muxings which
can be used depending on board design.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
i2c3 controller can use several sets of pins depending
on board design. This patch adds the missing alternate
pinconfigs.
Signed-off-by: Seraphin Bonnaffe <seraphin.bonnaffe@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This pin setup provides the correct configuration in order to
interact with the CEC HW.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Nicolas Vanhaelewyn <nicolas.vanhaelewyn@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
mtsin0 channel can only be configured for parallel data transfer.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
tsout1 channel can only be configured for serial data tranfer.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
tsout0 channel can be configured for either serial or parallel
data transfer. Both pin configurations are provided.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
tsin5 can only be configured for serial data transfer. However
depending on board design, two alternate tsin5 pin configurations
are available, both in pin-controller-front0.
pinctrl_tsin5_serial_alt1 is brought out on B2120 reference
design as TSD on NIMB slot of the B2004A daughter board.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
tsin4 can only be configured for serial data transfer. However
depending on board design, two alternate pin configurations
are available. One in pin-controller-front0 and the other in
pin-controller-front1.
pinctrl_tsin4_serial_alt3 is brought out on B2120 reference
design as TSC on NIMA slot of the B2004A daughter board.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
tsin3 channel can only be configured for serial data transfer.
On B2120 reference design tsin3 is brought out as TSB on the NIMB
slot of the B2004A daughter board.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
tsin2 channel can be configured for either serial or parallel data
transfer. This patch adds the pinctrl config for both possibilities.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
tsin1 channel can be configured for either serial or parallel data
transfer. This patch adds the pinctrl config for both possibilities.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
tsin0 and be configured as either serial or parallel. This patch
adds the pinctrl config for both possiblities. On B2120 reference
design tsin0 is brought out as TSA on the NIMA slot of the B2004A
daughter board.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This will avoid programming the retime registers when not implemented
- PIO5 : no retime registers assigned to pins 6 and 7
- PIO35 : pin 7 is reserved so no retime register assigned to it
Signed-off-by: Karim BEN BELGACEM <karim.ben-belgacem@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
The STiH407 is advanced multi-HD AVC processor with 3D graphics acceleration
and 1.5-GHz ARM Cortex-A9 SMP CPU.
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
