The ALWAYS_SYNC flag is currently honored by the usb-storage driver but not UAS
and is required to work around devices that become unstable upon being
queried for cache. This code is taken straight from:
drivers/usb/storage/scsiglue.c:284
Signed-off-by: Alexander Kappner <agk@godking.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB Type-C PHY in Intel WhiskeyCove PMIC has build-in
USB Type-C state machine which we were relying on to
configure the CC lines correctly. This patch removes that
dependency and configures the CC line according to commands
from the port manager (tcpm.c) in wcove_set_cc().
This fixes an issue where USB devices attached to the USB
Type-C port do not get enumerated. When acting as
source/host, the HW FSM sometimes fails to configure the PHY
correctly.
Fixes: 3c4fb9f169 ("usb: typec: wcove: start using tcpm for USB PD support")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes an issue where the mux does not get configured
when the parent device is suspended. The registers for this
mux are mapped to the parent device MMIO (usually xHCI PCI
device), so in order for the driver to be able to program
the registers, the parent device must be resumed.
Reported-by: Sathyanarayanan Kuppuswamy <sathyanarayanan.kuppuswamy@intel.com>
Fixes: f6fb9ec02b ("usb: roles: Add Intel xHCI USB role switch driver")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removing the "fusb302" debugfs directory when unloading
the driver. That allows the driver to be loaded more then
one time. The directory will not get actually removed until
it is empty, so only after the last instance has been
removed.
This fixes an issue where the driver can't be re-loaded if
it has been unloaded as the "fusb302" debugfs directory
already exists.
Fixes: 76f0c53d08 ("usb: typec: fusb302: Move out of staging")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver will not probe unless bq24190 is loaded, so
making it a dependency.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trying to determine the USB port type with this mux is very
difficult. To simplify the situation, always allow user
control, even if the port is USB Type-C port.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix htmldocs warning:
drivers/usb/typec/mux.c:186: warning: Function parameter or member 'mux' not described in
'typec_mux_unregister'
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: bdecb33af3 ("usb: typec: API for controlling USB Type-C Multiplexers")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pdev_nr and rhport can be controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/usb/usbip/vhci_sysfs.c:238 detach_store() warn: potential spectre issue 'vhcis'
drivers/usb/usbip/vhci_sysfs.c:328 attach_store() warn: potential spectre issue 'vhcis'
drivers/usb/usbip/vhci_sysfs.c:338 attach_store() warn: potential spectre issue 'vhci->vhci_hcd_ss->vdev'
drivers/usb/usbip/vhci_sysfs.c:340 attach_store() warn: potential spectre issue 'vhci->vhci_hcd_hs->vdev'
Fix this by sanitizing pdev_nr and rhport before using them to index
vhcis and vhci->vhci_hcd_ss->vdev respectively.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When printer_write() calls usb_ep_queue(), a udc driver (e.g.
renesas_usbhs driver) may call usb_gadget_giveback_request() in
the udc .queue ops immediately. Then, printer_write() calls
list_add(&req->list, &dev->tx_reqs_active) wrongly. After that,
if we do unbind the printer driver, WARN_ON() happens in
printer_func_unbind() because the list entry is not removed.
So, this patch moves list_add(&req->list, &dev->tx_reqs_active)
calling before usb_ep_queue().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For supply registration, provide fwnode pointer of the port device,
via the power_supply_config structure, to allow other psy drivers
to add us as a supplier. At present this only applies to DT
based platforms using the 'power-supplies' DT property, but in the
future should also work for ACPI platforms when the relevant support
is added to the power_supply core.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To allow users of the power supply framework to be hw description
agnostic, this commit adds the ability to pass a fwnode pointer,
via the power_supply_config structure, to the initialisation code
of the core, instead of explicitly specifying of_ndoe. If that
fwnode pointer is provided then it will automatically resolve down
to of_node on platforms which support it, otherwise it will be NULL.
In the future, when ACPI support is added, this can be modified to
accommodate ACPI without the need to change calling code which
already provides the fwnode handle in this manner.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The notifier callbacks of extcon are called in atomic context, but the
callbacks will call regulator_enable()/regulator_disable() which may
sleep caused by mutex, so use work queue to call the sleep functions.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When VBUS_FALL interrupt arises, it means U3 device is disconnected
with host, so need reset status of gadget
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clear test_mode flag when the gadget is reset by host, otherwise
will affect the next test item.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reset EP when disable it to reset data toggle for U2 EP, and
SeqN, flow control status etc for U3 EP, this can avoid
issue of uncontinuous SeqN
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the controller receives a LPM request, it will reject the LPM
request, and need software to re-enable it after LPM resume if the
controller doesn't remote wakeup from L1 automatically
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable compliance transition for a port by writing "compliance" to the
ports portsc file in debugfs.
port must be "Not-connected" and Link must be in RxDetect state to enable
compliance mode.
Only needed for host that have CTC flag set.
Allows state transitioning to compliance at 1st LFPS timeout.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add ports/portxx/portsc for each xHC hardware usb port to debugfs.
Showing the content of the port status and control register for
each port (PORTSC)
Portxx is numbered starting from 1 for historical reasons to better
match port numbering shown by lsusb and other places.
Ports in debugfs are in the order XHC controller has them,
In most cases USB2 ports come first, followed by USB3 ports.
i.e. USB2 ports are port01-portxx, and USB3 portxx-portmax.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As we are now using the new port strtuctes the port_arrays
are no longer needed, remove them completely
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_get_ports() is one of the last functions using port_arrays in
xhci-hub.c. We get the same data directly from hub and port structures
instead, so convert and remove both xhci_get_ports() and port_arrays from
all function that no longer need it.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
get rid of port iomem arrays and use port structures in the following
functions:
xhci_find_raw_port_number()
xhci_disable_port_wake_on_bits()
xhci_set_usb2_hardware_lpm()
xhci_all_ports_seen_u0()
compliance_mode_recovery()
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't use pointers to port array and port index as function parameters
in xhci_test_and_clear_bit(), just use a pointer to the right port
structure.
xhci_test_and_clear_bit() was the last port_array user in
xhci_get_port_status() and handle_port_status(), so remove the
port_array from them as well.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove old iomem port array and index as parameters, just
send a ponter to a port strucure instread
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hcd_portnum is a better desctiption than faked_port_index, and
is in line with the name the port structure uses.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
use port structures in the port event handler.
Getting the right hcd and hcd portnumber from the hardware port number
is a lot easier with port structures, and allows us to remove a lot
of the previous code, including the find_faked_portnum_from_hw_index()
function
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use port structures instead of mmio port arrays for
xhci_port_missing_cas_quirk() and xhci_set_remote_wake_mask() in
xhci-hub.c
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new port structures for functions in xhci-hub.c to get
port mmio address of portsc register instead of the port array
xhci_get_port_io_addr() is no longer needeed and is removed.
Plan is to get rid of the mmio port array completely.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
quick way to get the xhci roothub and thus all the ports
belonging to a certain hcd
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allows us to know the correct hcd a xhci roothub and its ports
belong to.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current way of having one array telling only the port speed,
and then two separate arrays with mmio addresses for usb2 and usb3 ports
requeres helper functions to transate hw to hcd, and hcd to hw port
numbers, and is hard to expand.
Instead create a structure describing a port, including the mmio address,
the port hardware index, hcd port index, and a pointer to the roothub
it belongs to.
Create one array containing all port structures in the same order the
hardware controller sees them. Then add an array of port pointers to
each xhci hub structure pointing to the ports that belonging to the
roothub.
This way we can easily convert hw indexed port events to usb core
hcd port numbers, and vice versa usb core hub hcd port numbers
to hw index and mmio address.
Other benefit is that we can easily find the parent hcd and xhci
structure of a port structure. This is useful in debugfs where
we can give one port structure pointer as parameter and get both
the correct mmio address and xhci lock needed to set some port
parameter.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for HiSilicon STB xHCI host controller.
There are two xHCI host controllers on HiSilicon STB SoCs. Each
one requires additional configuration before exposing interface
compliant with xHCI.
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Jianguo Sun <sunjianguo1@huawei.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A total of 98 non-merge commits, the biggest part being in dwc3 this
time around with a large refactoring of dwc3's transfer handling code.
We also have a new driver for Aspeed virtual hub controller.
Apart from that, just a list of miscellaneous fixes all over the place.
-----BEGIN PGP SIGNATURE-----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=b56m
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: changes for v4.18 merge window
A total of 98 non-merge commits, the biggest part being in dwc3 this
time around with a large refactoring of dwc3's transfer handling code.
We also have a new driver for Aspeed virtual hub controller.
Apart from that, just a list of miscellaneous fixes all over the place.
UDC core ensures the usb_ep parameter passed in is not NULL, so
checking if (ep != NULL) is pointless.
Convert to_musb_ep() to a simple macro to not directly return NULL to
avoid warnings from code static analysis tools.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gadget function drivers should ensure the usb_request parameter
passed in is not NULL. UDC core doesn't check if it is NULL, so MUSB
driver shouldn't have to check it either.
Convert to_musb_request() to a simple macro to not directly return NULL
to avoid warnings from code static analysis tools.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To be able to use DSPS-based controllers with device-tree descriptions
of the USB topology, we need to associate the glue device's device-tree
node with the child controller device.
Note that this can also be used to eventually let USB core manage
generic phys.
Also note that the other glue drivers will require similar changes to be
able to describe their buses in DT.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As decided in the discussion [1] we are deleting the otg protocol
support from the musb drivers.
First this patch disables the flags for enabling the otg protocols. We
will later gradually delete the otg protocol code from the musb drivers.
[1] https://www.spinics.net/lists/linux-usb/msg167003.html
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
musb drivers do not use the otg fsm framework, so referencing to
otg->default_a doesn't have any effect, so remove the references.
But tusb6010 glue driver uses it locally to control the vbus power, so
keep the references in tusb6010 only.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
musb_stage0_irq() is 400+ lines long. Break its interrupt events
handling into each individual functions to make it easy to read.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following members in struct musb_hdrc_config are not used,
so remove them.
soft_con
utm_16
big_endian
mult_bulk_tx
mult_bulk_rx
high_iso_tx
high_iso_rx
dma
dma_channels
dyn_fifo_size
vendor_ctrl
vendor_stat
vendor_req
dma_req_chan
musb_hdrc_eps_bits
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
include/linux/usb/musb.h already defines enum for musb port mode, so
remove the duplicate in musb_core.h and use the definition in musb.h.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
musb_core already has musb_get_mode(), so remove the duplicate from
musb_dsps.c.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both musb_io and musb_platform_ops in struct musb define a quirks flag
for the same purpose. Let's remove the one in struct musb_io, and use
that in struct musb_platform_ops instead.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following wrappers were defined because of Blackfin support. Now
Blackfin support is removed, these wrappers are no longer needed, so
remove them.
musb_write_txfifosz
musb_write_txfifoadd
musb_write_rxfifosz
musb_write_rxfifoadd
musb_write_ulpi_buscontrol
musb_read_txfifosz
musb_read_txfifoadd
musb_read_rxfifosz
musb_read_rxfifoadd
musb_read_ulpi_buscontrol
musb_read_hwvers
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now Blackfin support is removed, nobody uses adjust_channel_params() any
more, so remove it from struct musb_platform_ops.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now Blackfin support is removed, we no longer need function pointers for
musb_readl() and musb_writel().
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
