Commit d23b9b00cd (PM / Domains: Rework
system suspend callback routines (v2)) broke the system suspend and
resume handling by devices belonging to generic PM domains, because
it used freeze/thaw callbacks instead of suspend/resume ones and
didn't initialize device callbacks for system suspend/resume
properly at all. Fix those problems.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add a name member pointer to struct generic_pm_domain and use it in
diagnostic messages regarding the domain power-off and power-on
latencies. Update the ARM shmobile SH7372 code to assign names to
the PM domains used by it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Measure the time of execution of the .stop(), .start(), .save_state()
and .restore_state() PM domain device callbacks and if the result
is greater than the corresponding latency value stored in the
device's struct generic_pm_domain_data object, replace the inaccurate
value with the measured time.
Do analogously for the PM domains' .power_off() and .power_off()
callbacks.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add a function deciding whether or not a given PM domain should
be powered off on the basis of the PM QoS constraints of devices
belonging to it and their PM QoS timing data.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add a function deciding whether or not devices should be stopped in
pm_genpd_runtime_suspend() depending on their PM QoS constraints
and stop/start timing values. Make it possible to add information
used by this function to device objects.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
The current generic PM domains code attempts to use the generic
system suspend operations along with the domains' device stop/start
routines, which requires device drivers to assume that their
system suspend/resume (and hibernation/restore) callbacks will always
be used with generic PM domains. However, in theory, the same
hardware may be used in devices that don't belong to any PM domain,
in which case it would be necessary to add "fake" PM domains to
satisfy the above assumption. Also, the domain the hardware belongs
to may not be handled with the help of the generic code.
To allow device drivers that may be used along with the generic PM
domains code of more flexibility, add new device callbacks,
.suspend(), .suspend_late(), .resume_early(), .resume(), .freeze(),
.freeze_late(), .thaw_early(), and .thaw(), that can be supplied by
the drivers in addition to their "standard" system suspend and
hibernation callbacks. These new callbacks, if defined, will be used
by the generic PM domains code for the handling of system suspend and
hibernation instead of the "standard" ones. This will allow drivers
to be designed to work with generic PM domains as well as without
them.
For backwards compatibility, introduce default implementations of the
new callbacks for PM domains that will execute pm_generic_suspend(),
pm_generic_suspend_noirq(), pm_generic_resume_noirq(),
pm_generic_resume(), pm_generic_freeze(), pm_generic_freeze_noirq(),
pm_generic_thaw_noirq(), and pm_generic_thaw(), respectively, for the
given device if its driver doesn't define those callbacks.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The current PM domains code uses device drivers' .runtime_suspend()
and .runtime_resume() callbacks as the "save device state" and
"restore device state" operations, which may not be appropriate in
general, because it forces drivers to assume that they always will
be used with generic PM domains. However, in theory, the same
hardware may be used in devices that don't belong to any PM
domain, in which case it would be necessary to add "fake" PM
domains to satisfy the above assumption. It also may be located in
a PM domain that's not handled with the help of the generic code.
To allow device drivers that may be used along with the generic PM
domains code of more flexibility, introduce new device callbacks,
.save_state() and .restore_state(), that can be supplied by the
drivers in addition to their "standard" runtime PM callbacks. This
will allow the drivers to be designed to work with generic PM domains
as well as without them.
For backwards compatibility, introduce default .save_state() and
.restore_state() callback routines for PM domains that will execute
a device driver's .runtime_suspend() and .runtime_resume() callbacks,
respectively, for the given device if the driver doesn't provide its
own implementations of .save_state() and .restore_state().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The current generic PM domains code requires that the same .stop(),
.start() and .active_wakeup() device callback routines be used for
all devices in the given domain, which is inflexible and may not
cover some specific use cases. For this reason, make it possible to
use device specific .start()/.stop() and .active_wakeup() callback
routines by adding corresponding callback pointers to struct
generic_pm_domain_data. Add a new helper routine,
pm_genpd_register_callbacks(), that can be used to populate
the new per-device callback pointers.
Modify the shmobile's power domains code to allow drivers to add
their own code to be run during the device stop and start operations
with the help of the new callback pointers.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: twl: fix twl4030 support for smps regulators
regulator: fix use after free bug
regulator: aat2870: Fix the logic of checking if no id is matched in aat2870_get_regulator
Commit f2c31e32b3 ("net: fix NULL dereferences in check_peer_redir()")
forgot to take care of infiniband uses of dst neighbours.
Many thanks to Marc Aurele who provided a nice bug report and feedback.
Reported-by: Marc Aurele La France <tsi@ualberta.ca>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This following can occur with ipoib when processing a multicast reponse:
BUG: soft lockup - CPU#0 stuck for 67s! [ib_mad1:982]
Modules linked in: ...
CPU 0:
Modules linked in: ...
Pid: 982, comm: ib_mad1 Not tainted 2.6.32-131.0.15.el6.x86_64 #1 ProLiant DL160 G5
RIP: 0010:[<ffffffff814ddb27>] [<ffffffff814ddb27>] _spin_unlock_irqrestore+0x17/0x20
RSP: 0018:ffff8802119ed860 EFLAGS: 00000246
0000000000000004 RBX: ffff8802119ed860 RCX: 000000000000a299
RDX: ffff88021086c700 RSI: 0000000000000246 RDI: 0000000000000246
RBP: ffffffff8100bc8e R08: ffff880210ac229c R09: 0000000000000000
R10: ffff88021278aab8 R11: 0000000000000000 R12: ffff8802119ed860
R13: ffffffff8100be6e R14: 0000000000000001 R15: 0000000000000003
FS: 0000000000000000(0000) GS:ffff880028200000(0000) knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 00000000006d4840 CR3: 0000000209aa5000 CR4: 00000000000406f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Call Trace:
[<ffffffffa032c247>] ? ipoib_mcast_send+0x157/0x480 [ib_ipoib]
[<ffffffff8100bc8e>] ? apic_timer_interrupt+0xe/0x20
[<ffffffff8100bc8e>] ? apic_timer_interrupt+0xe/0x20
[<ffffffffa03283d4>] ? ipoib_path_lookup+0x124/0x2d0 [ib_ipoib]
[<ffffffffa03286fc>] ? ipoib_start_xmit+0x17c/0x430 [ib_ipoib]
[<ffffffff8141e758>] ? dev_hard_start_xmit+0x2c8/0x3f0
[<ffffffff81439d0a>] ? sch_direct_xmit+0x15a/0x1c0
[<ffffffff81423098>] ? dev_queue_xmit+0x388/0x4d0
[<ffffffffa032d6b7>] ? ipoib_mcast_join_finish+0x2c7/0x510 [ib_ipoib]
[<ffffffffa032dab8>] ? ipoib_mcast_sendonly_join_complete+0x1b8/0x1f0 [ib_ipoib]
[<ffffffffa02a0946>] ? mcast_work_handler+0x1a6/0x710 [ib_sa]
[<ffffffffa015f01e>] ? ib_send_mad+0xfe/0x3c0 [ib_mad]
[<ffffffffa00f6c93>] ? ib_get_cached_lmc+0xa3/0xb0 [ib_core]
[<ffffffffa02a0f9b>] ? join_handler+0xeb/0x200 [ib_sa]
[<ffffffffa029e4fc>] ? ib_sa_mcmember_rec_callback+0x5c/0xa0 [ib_sa]
[<ffffffffa029e79c>] ? recv_handler+0x3c/0x70 [ib_sa]
[<ffffffffa01603a4>] ? ib_mad_completion_handler+0x844/0x9d0 [ib_mad]
[<ffffffffa015fb60>] ? ib_mad_completion_handler+0x0/0x9d0 [ib_mad]
[<ffffffff81088830>] ? worker_thread+0x170/0x2a0
[<ffffffff8108e160>] ? autoremove_wake_function+0x0/0x40
[<ffffffff810886c0>] ? worker_thread+0x0/0x2a0
[<ffffffff8108ddf6>] ? kthread+0x96/0xa0
[<ffffffff8100c1ca>] ? child_rip+0xa/0x20
Coinciding with stack trace is the following message:
ib0: ib_address_create failed
The code below in ipoib_mcast_join_finish() will note the above
failure in the address handle but otherwise continue:
ah = ipoib_create_ah(dev, priv->pd, &av);
if (!ah) {
ipoib_warn(priv, "ib_address_create failed\n");
} else {
The while loop at the bottom of ipoib_mcast_join_finish() will attempt
to send queued multicast packets in mcast->pkt_queue and eventually
end up in ipoib_mcast_send():
if (!mcast->ah) {
if (skb_queue_len(&mcast->pkt_queue) < IPOIB_MAX_MCAST_QUEUE)
skb_queue_tail(&mcast->pkt_queue, skb);
else {
++dev->stats.tx_dropped;
dev_kfree_skb_any(skb);
}
My read is that the code will requeue the packet and return to the
ipoib_mcast_join_finish() while loop and the stage is set for the
"hung" task diagnostic as the while loop never sees a non-NULL ah, and
will do nothing to resolve.
There are GFP_ATOMIC allocates in the provider routines, so this is
possible and should be dealt with.
The test that induced the failure is associated with a host SM on the
same server during a shutdown.
This patch causes ipoib_mcast_join_finish() to exit with an error
which will flush the queued mcast packets. Nothing is done to unwind
the QP attached state so that subsequent sends from above will retry
the join.
Reviewed-by: Ram Vepa <ram.vepa@qlogic.com>
Reviewed-by: Gary Leshner <gary.leshner@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
With the revert of "of/irq: of_irq_find_parent: check for parent equal to
child" (dc93728084), we need another way to handle parent node equal
to the child node. This can simply be handled in of_irq_init by checking
for this condition.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Tested-by: Pawel Moll <pawel.moll@arm.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: convert drivers/hwmon/* to use module_platform_driver()
hwmon: Remove redundant spi driver bus initialization
In the case where CONFIG_PSTORE=n, the function efi_pstore_read() doesn't
have the correct list of parameters. This patch provides a definition
of efi_pstore_read() with 'char **buf' added to fix this warning:
"drivers/firmware/efivars.c:609: warning: initialization from".
problem introduced in commit f6f8285132
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Don't over-schedule QSFP work on driver initialization. It could end
up being run simultaneously on two different CPUs resulting in bad
EEPROM reads. In combination with setting the physical IB link state
prior to the IBC being brought out of reset, this can cause the link
state machine to start training early with wrong settings.
Signed-off-by: Mitko Haralanov <mitko@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix logic so that we don't retry with MPAv1 once we have done that
already. Otherwise, we end up retrying with MPAv1 even when its not
needed on getting peer aborts - and this could lead to kernel panic.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix another place in the code where logic dealing with the t4_cqe was
using the wrong QID. This fixes the counting logic so that it tests
against the SQ QID instead of the RQ QID when counting RCQES.
Signed-off by: Jonathan Lallinger <jonathan@ogc.us>
Signed-off by: Steve Wise <swise@ogc.us>
Signed-off-by: Roland Dreier <roland@purestorage.com>
SMPS regulator voltage control differs from the one of the LDO ones.
Current TWL code was using LDO regulator ops for controlling the SMPS
regulators, which fails. This was fixed fixed by adding separate
regulator type which uses correct logic and calculations for the
voltage levels.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
This is caused by dereferencing 'rdev' after device_unregister() in
the regulator_unregister() function. 'rdev' is freed by
device_unregister(), so it must not be dereferenced after this call.
[Edited commit message for legibility -- broonie]
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In current implementation, the pointer ri is not NULL if no id is matched.
Fix it by checking i == ARRAY_SIZE(aat2870_regulators) if no id is matched.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
* 'fbdev-for-linus' of git://github.com/schandinat/linux-2.6:
viafb: correct sync polarity for OLPC DCON
video:da8xx-fb: Disable and reset sequence on version2 of LCDC
OMAPDSS: DISPC: skip scaling calculations when not scaling
OMAPFB: fix compilation warnings due to missing include
OMAPDSS: HDMI: fix returned HDMI pixel clock
Revert a hunk in drivers/net/wireless/ath/ath9k/hw.c introduced by
commit 2577c6e8f2 ("ath9k_hw: Add support for AR946/8x chipsets") that
caused a nasty regression to appear on my Acer Ferrari One (the box
locks up entirely at random times after the wireless has been started
without any way to get debug information out of it).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix build failure in staging iio driver:
.../drivers/staging/iio/industrialio-core.c: In function 'iio_event_getfd':
.../drivers/staging/iio/industrialio-core.c:262:32: error:
'ev_int' undeclared (first use in this function)
Also convert the rest of the function to use the new variable.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch converts the drivers in drivers/hwmon/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Cc: Donggeun Kim <dg77.kim@samsung.com>
Cc: Simon Guinot <sguinot@lacie.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: J Keerthy <j-keerthy@ti.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
In ancient times it was necessary to manually initialize the bus field of an
spi_driver to spi_bus_type. These days this is done in spi_register_driver(),
so we can drop the manual assignment.
The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
.driver = {
- .bus = &spi_bus_type,
},
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: lm-sensors@lm-sensors.org
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
compatible in dts has been changed, so the driver needs to be updated
accordingly.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* git://github.com/rustyrussell/linux:
virtio-pci: make reset operation safer
virtio-mmio: Correct the name of the guest features selector
virtio: add HAS_IOMEM dependency to MMIO platform bus driver
virtio pci device reset actually just does an I/O
write, which in PCI is really posted, that is it
can complete on CPU before the device has received it.
Further, interrupts might have been pending on
another CPU, so device callback might get invoked after reset.
This conflicts with how drivers use reset, which is typically:
reset
unregister
a callback running after reset completed can race with
unregister, potentially leading to use after free bugs.
Fix by flushing out the write, and flushing pending interrupts.
This assumes that device is never reset from
its vq/config callbacks, or in parallel with being
added/removed, document this assumption.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Fix this compile error on s390:
CC [M] drivers/virtio/virtio_mmio.o
drivers/virtio/virtio_mmio.c: In function 'vm_get_features':
drivers/virtio/virtio_mmio.c:107:2: error: implicit declaration of function 'writel'
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci:
PCI hotplug: shpchp: don't blindly claim non-AMD 0x7450 device IDs
PCI: pciehp: wait 100 ms after Link Training check
PCI: pciehp: wait 1000 ms before Link Training check
PCI: pciehp: Retrieve link speed after link is trained
PCI: Let PCI_PRI depend on PCI
PCI: Fix compile errors with PCI_ATS and !PCI_IOV
PCI / ACPI: Make acpiphp ignore root bridges using PCIe native hotplug
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (31 commits)
drm: integer overflow in drm_mode_dirtyfb_ioctl()
drivers/gpu/vga/vgaarb.c: add missing kfree
drm/radeon/kms/atom: unify i2c gpio table handling
drm/radeon/kms: fix up gpio i2c mask bits for r4xx for real
ttm: Don't return the bo reserved on error path
drm/radeon/kms: add a CS ioctl flag not to rewrite tiling flags in the CS
drm/i915: Fix inconsistent backlight level during disabled
drm, i915: Fix memory leak in i915_gem_busy_ioctl().
drm/i915: Use DPCD value for max DP lanes.
drm/i915: Initiate DP link training only on the lanes we'll be using
drm/i915: Remove trailing white space
drm/i915: Try harder during dp pattern 1 link training
drm/i915: Make DP prepare/commit consistent with DP dpms
drm/i915: Let panel power sequencing hardware do its job
drm/i915: Treat PCH eDP like DP in most places
drm/i915: Remove link_status field from intel_dp structure
drm/i915: Move common PCH_PP_CONTROL setup to ironlake_get_pp_control
drm/i915: Module parameters using '-1' as default must be signed type
drm/i915: Turn on another required clock gating bit on gen6.
drm/i915: Turn on a required 3D clock gating bit on Sandybridge.
...
Count of selector voltage is required for regulator_set_voltage
to work via set_voltage_sel. VDD1/2 currently have it as zero,
so regulator_set_voltage won't work for VDD1/2.
Update count (n_voltages) for VDD1/2.
Output Voltage = (step value * 12.5 mV + 562.5 mV) * gain
With above expr, number of voltages that can be selected is
step value count * gain count
constant for gain count will be called VDD1_2_NUM_VOLT_COARSE
existing constant for step value count is VDD1_2_NUM_VOLTS,
use VDD1_2_NUM_VOLT_FINE instead to make clear that step value
is not the only component in deciding selectable voltage count
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The function i2cdev_notifier_call is used only in i2c-dev file
making it static.
Also removes the following sparse warning
drivers/i2c/i2c-dev.c:582:5: warning: symbol 'i2cdev_notifier_call'
was not declared. Should it be static?
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
10-bit addresses overlap with traditional 7-bit addresses, leading in
device name collisions. Add an arbitrary offset to 10-bit addresses to
prevent this collision. The offset was chosen so that the address is
still easily recognizable.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
The wrong bits were put on the wire, fix that.
This fixes kernel bug #42562.
Signed-off-by: Sheng-Hui J. Chu <jeffchu@broadcom.com>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
There is a potential integer overflow in drm_mode_dirtyfb_ioctl()
if userspace passes in a large num_clips. The call to kmalloc would
allocate a small buffer, and the call to fb->funcs->dirty may result
in a memory corruption.
Reported-by: Haogang Chen <haogangchen@gmail.com>
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
