The lantiq-ssc driver uses internally an own workqueue to wait till the
data is not only written out of the FIFO but really written to the wire.
This workqueue is flushed while the SPI subsystem is working in some
other system workqueue.
The system workqueue is marked as WQ_MEM_RECLAIM, but the workqueue in
the lantiq-ssc driver does not use WQ_MEM_RECLAIM for now. Add this flag
too to prevent this warning.
This fixes the following warning:
[ 2.975956] WARNING: CPU: 1 PID: 17 at kernel/workqueue.c:2614 check_flush_dependency+0x168/0x184
[ 2.984752] workqueue: WQ_MEM_RECLAIM kblockd:blk_mq_run_work_fn is flushing !WQ_MEM_RECLAIM 1e100800.spi:0x0
Fixes: 891b7c5fbf ("mtd_blkdevs: convert to blk-mq")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://lore.kernel.org/r/20200717215648.20522-1-hauke@hauke-m.de
Signed-off-by: Mark Brown <broonie@kernel.org>
A couple of small driver specific fixes for fairly minor issues.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl8Rl3ETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0DrYCACFJjlpdg7+LFK+zoQwIY9JPFd/VQWD
X0xxnpJVxBRwyoAFbjfN0TfEg4lZ7KtbOBt91T7MaxUTtLet6KSuf+1ADuZSKe4Y
K9eb1i+J1zjYzkVTDhlSCmIUIVOufZqxGPSQjuPjQhbOyT+SjyfyQhrJ0Atof8gb
EyyrkQjwiC6y6xW0TpxEcrC4Toku5Si2YbH8RkOgH3puaZ03wVzLxNNeDxPPUFSh
uu6IvXuzE+6p1MlTF13nd4TFkFRu1QNUVPL7PRlXvU9a1YtYzxp6tPYlOtnWvrER
vh2u2QfR90LeVy+r7RizJO7bfBy90H7yB8qKRPOPn3v2UhImYDEwfqtm
=zprr
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v5.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi into master
Pull spi fixes from Mark Brown:
"A couple of small driver specific fixes for fairly minor issues"
* tag 'spi-fix-v5.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-sun6i: sun6i_spi_transfer_one(): fix setting of clock rate
spi: mediatek: use correct SPI_CFG2_REG MACRO
A SPI transfer defines the _maximum_ speed of the SPI transfer. However the
driver doesn't take into account that the clock divider is always rounded down
(due to integer arithmetics). This results in a too high clock rate for the SPI
transfer.
E.g.: with a mclk_rate of 24 MHz and a SPI transfer speed of 10 MHz, the
original code calculates a reg of "0", which results in a effective divider of
"2" and a 12 MHz clock for the SPI transfer.
This patch fixes the issue by using DIV_ROUND_UP() instead of a plain
integer division.
While there simplify the divider calculation for the CDR1 case, use
order_base_2() instead of two ilog2() calculations.
Fixes: 3558fe900e ("spi: sunxi: Add Allwinner A31 SPI controller driver")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200706143443.9855-2-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
A batch of fixes for the Freescale DSPI driver fixing some serious
issues with removal of active devices and one resume case, plus a few
new PCI IDs for Intel platforms.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl76FzkTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0C5iB/0ThW3V0f9NKiIPkJjgp4DYfhYL8cKO
z4fOeOdJHOm73Atd5efhfU58REpEjmAD76O++/z4qD1l5wRsfILCObEsMwPYRTzr
gYlFVaNuZ3wAz8rDYU7VfmdzuZKRfhAUxJKovcLJleBmWAsGk3fHd5oBPVNJQPl3
jx1Wnj37T2dykI+jhRjQuRbN4e+1FxOKNHcVmwkoUx9OKX1cbRczE5mYhPf8zD2K
ZMMlfuyPg1zqfsVRzBSjaqsbMLZY4tgYemwQmLthhMvMZJ1cw4bt1RMgVBKlzPZN
X+vr5vh9HA8y6spJoAfffBCtIr7BVsNpXXi11QMozZ6YgnBUSJDZeN8Q
=OauP
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v5.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A batch of fixes for the Freescale DSPI driver fixing some serious
issues with removal of active devices and one resume case, plus a few
new PCI IDs for Intel platforms"
* tag 'spi-fix-v5.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: pxa2xx: Add support for Intel Tiger Lake PCH-H
spi: spi-fsl-dspi: Initialize completion before possible interrupt
spi: spi-fsl-dspi: Fix external abort on interrupt in resume or exit paths
spi: spi-fsl-dspi: Fix lockup if device is shutdown during SPI transfer
spi: spi-fsl-dspi: Fix lockup if device is removed during SPI transfer
Quite a lot of fixes here for no single reason. There's a collection of
the usual sort of device specific fixes and also a bunch of people have
been working on spidev and the userspace test program spidev_test so
they've got an unusually large collection of small fixes.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl7wl/8THGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0NJBB/4oTOxPIfkKQyPcSTQB8FC6AHJ5Z8FT
/4dtK4U32rn5Sms/CHNXMMFxomBgB46Ud19KJ/bEgqugJfI9Vl0bl9fZT+sDyVU3
rFPthVluIprFe1bITyfcgYmjRoznLRdzj9LMFsAWIe3Vmy584TdvXbl8n5COu5Wh
6sR6SuQnEn65x1HC4++3IsG70+ogz81sFRapk/7jXwS+YdwzWIqtN2s2IlUcTmcy
ylijl04XUSyo6e/v/sjZaaRmIz72mW+HbMKW4iC0mGZ6yuACoy7zop9BuwAg6S7z
dFDyqTZ5gq72ZeJc7fuco1y7jqQoKUC1oTRghPlbq2XG3Huta80l415l
=32lr
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v5.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"Quite a lot of fixes here for no single reason.
There's a collection of the usual sort of device specific fixes and
also a bunch of people have been working on spidev and the userspace
test program spidev_test so they've got an unusually large collection
of small fixes"
* tag 'spi-fix-v5.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spidev: fix a potential use-after-free in spidev_release()
spi: spidev: fix a race between spidev_release and spidev_remove
spi: stm32-qspi: Fix error path in case of -EPROBE_DEFER
spi: uapi: spidev: Use TABs for alignment
spi: spi-fsl-dspi: Free DMA memory with matching function
spi: tools: Add macro definitions to fix build errors
spi: tools: Make default_tx/rx and input_tx static
spi: dt-bindings: amlogic, meson-gx-spicc: Fix schema for meson-g12a
spi: rspi: Use requested instead of maximum bit rate
spi: spidev_test: Use %u to format unsigned numbers
spi: sprd: switch the sequence of setting WDG_LOAD_LOW and _HIGH
The interrupt handler calls completion and is IRQ requested before the
completion is initialized. Logically it should be the other way.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200622110543.5035-4-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
If shared interrupt comes late, during probe error path or device remove
(could be triggered with CONFIG_DEBUG_SHIRQ), the interrupt handler
dspi_interrupt() will access registers with the clock being disabled.
This leads to external abort on non-linefetch on Toradex Colibri VF50
module (with Vybrid VF5xx):
$ echo 4002d000.spi > /sys/devices/platform/soc/40000000.bus/4002d000.spi/driver/unbind
Unhandled fault: external abort on non-linefetch (0x1008) at 0x8887f02c
Internal error: : 1008 [#1] ARM
Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
Backtrace:
(regmap_mmio_read32le)
(regmap_mmio_read)
(_regmap_bus_reg_read)
(_regmap_read)
(regmap_read)
(dspi_interrupt)
(free_irq)
(devm_irq_release)
(release_nodes)
(devres_release_all)
(device_release_driver_internal)
The resource-managed framework should not be used for shared interrupt
handling, because the interrupt handler might be called after releasing
other resources and disabling clocks.
Similar bug could happen during suspend - the shared interrupt handler
could be invoked after suspending the device. Each device sharing this
interrupt line should disable the IRQ during suspend so handler will be
invoked only in following cases:
1. None suspended,
2. All devices resumed.
Fixes: 349ad66c0a ("spi:Add Freescale DSPI driver for Vybrid VF610 platform")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200622110543.5035-3-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
During shutdown, the driver should unregister the SPI controller
and stop the hardware. Otherwise the dspi_transfer_one_message() could
wait on completion infinitely.
Additionally, calling spi_unregister_controller() first in device
shutdown reverse-matches the probe function, where SPI controller is
registered at the end.
Fixes: dc23482599 ("spi: spi-fsl-dspi: Adding shutdown hook")
Reported-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200622110543.5035-2-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
During device removal, the driver should unregister the SPI controller
and stop the hardware. Otherwise the dspi_transfer_one_message() could
wait on completion infinitely.
Additionally, calling spi_unregister_controller() first in device
removal reverse-matches the probe function, where SPI controller is
registered at the end.
Fixes: 05209f4570 ("spi: fsl-dspi: add missing clk_disable_unprepare() in dspi_remove()")
Reported-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200622110543.5035-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
If an spi device is unbounded from the driver before the release
process, there will be an NULL pointer reference when it's
referenced in spi_slave_abort().
Fix it by checking it's already freed before reference.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@gmail.com>
Link: https://lore.kernel.org/r/20200618032125.4650-2-zhenzhong.duan@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of -EPROBE_DEFER, stm32_qspi_release() was called
in any case which unregistered driver from pm_runtime framework
even if it has not been registered yet to it. This leads to:
stm32-qspi 58003000.spi: can't setup spi0.0, status -13
spi_master spi0: spi_device register error /soc/spi@58003000/mx66l51235l@0
spi_master spi0: Failed to create SPI device for /soc/spi@58003000/mx66l51235l@0
stm32-qspi 58003000.spi: can't setup spi0.1, status -13
spi_master spi0: spi_device register error /soc/spi@58003000/mx66l51235l@1
spi_master spi0: Failed to create SPI device for /soc/spi@58003000/mx66l51235l@1
On v5.7 kernel,this issue was not "visible", qspi driver was probed
successfully.
Fixes: 9d282c17b0 ("spi: stm32-qspi: Add pm_runtime support")
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Link: https://lore.kernel.org/r/20200616113035.4514-1-patrice.chotard@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver allocates DMA memory with dma_alloc_coherent() but frees it with
dma_unmap_single().
This causes DMA warning during system shutdown (with DMA debugging) on
Toradex Colibri VF50 module:
WARNING: CPU: 0 PID: 1 at ../kernel/dma/debug.c:1036 check_unmap+0x3fc/0xb04
DMA-API: fsl-edma 40098000.dma-controller: device driver frees DMA memory with wrong function
[device address=0x0000000087040000] [size=8 bytes] [mapped as coherent] [unmapped as single]
Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
(unwind_backtrace) from [<8010bb34>] (show_stack+0x10/0x14)
(show_stack) from [<8011ced8>] (__warn+0xf0/0x108)
(__warn) from [<8011cf64>] (warn_slowpath_fmt+0x74/0xb8)
(warn_slowpath_fmt) from [<8017d170>] (check_unmap+0x3fc/0xb04)
(check_unmap) from [<8017d900>] (debug_dma_unmap_page+0x88/0x90)
(debug_dma_unmap_page) from [<80601d68>] (dspi_release_dma+0x88/0x110)
(dspi_release_dma) from [<80601e4c>] (dspi_shutdown+0x5c/0x80)
(dspi_shutdown) from [<805845f8>] (device_shutdown+0x17c/0x220)
(device_shutdown) from [<80143ef8>] (kernel_restart+0xc/0x50)
(kernel_restart) from [<801441cc>] (__do_sys_reboot+0x18c/0x210)
(__do_sys_reboot) from [<80100060>] (ret_fast_syscall+0x0/0x28)
DMA-API: Mapped at:
dma_alloc_attrs+0xa4/0x130
dspi_probe+0x568/0x7b4
platform_drv_probe+0x6c/0xa4
really_probe+0x208/0x348
driver_probe_device+0x5c/0xb4
Fixes: 90ba37033c ("spi: spi-fsl-dspi: Add DMA support for Vybrid")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1591803717-11218-1-git-send-email-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, the RSPI driver always tries to use the maximum configured
bit rate for communicating with a slave device, even if the transfer(s)
in the current message specify a lower rate.
Use the mininum rate specified in the message instead.
Rename rspi_data.max_speed_hz accordingly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200608095940.30516-3-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Here is the large set of char/misc driver patches for 5.8-rc1
Included in here are:
- habanalabs driver updates, loads
- mhi bus driver updates
- extcon driver updates
- clk driver updates (approved by the clock maintainer)
- firmware driver updates
- fpga driver updates
- gnss driver updates
- coresight driver updates
- interconnect driver updates
- parport driver updates (it's still alive!)
- nvmem driver updates
- soundwire driver updates
- visorbus driver updates
- w1 driver updates
- various misc driver updates
In short, loads of different driver subsystem updates along with the
drivers as well.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXtzkHw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yldOwCgus/DgpnI1UL4z+NdBxJrAXtkPmgAn2sgTUea
i5RblCmcVMqvHaGtYkY+
=tScN
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the large set of char/misc driver patches for 5.8-rc1
Included in here are:
- habanalabs driver updates, loads
- mhi bus driver updates
- extcon driver updates
- clk driver updates (approved by the clock maintainer)
- firmware driver updates
- fpga driver updates
- gnss driver updates
- coresight driver updates
- interconnect driver updates
- parport driver updates (it's still alive!)
- nvmem driver updates
- soundwire driver updates
- visorbus driver updates
- w1 driver updates
- various misc driver updates
In short, loads of different driver subsystem updates along with the
drivers as well.
All have been in linux-next for a while with no reported issues"
* tag 'char-misc-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (233 commits)
habanalabs: correctly cast u64 to void*
habanalabs: initialize variable to default value
extcon: arizona: Fix runtime PM imbalance on error
extcon: max14577: Add proper dt-compatible strings
extcon: adc-jack: Fix an error handling path in 'adc_jack_probe()'
extcon: remove redundant assignment to variable idx
w1: omap-hdq: print dev_err if irq flags are not cleared
w1: omap-hdq: fix interrupt handling which did show spurious timeouts
w1: omap-hdq: fix return value to be -1 if there is a timeout
w1: omap-hdq: cleanup to add missing newline for some dev_dbg
/dev/mem: Revoke mappings when a driver claims the region
misc: xilinx-sdfec: convert get_user_pages() --> pin_user_pages()
misc: xilinx-sdfec: cleanup return value in xsdfec_table_write()
misc: xilinx-sdfec: improve get_user_pages_fast() error handling
nvmem: qfprom: remove incorrect write support
habanalabs: handle MMU cache invalidation timeout
habanalabs: don't allow hard reset with open processes
habanalabs: GAUDI does not support soft-reset
habanalabs: add print for soft reset due to event
habanalabs: improve MMU cache invalidation code
...
The watchdog counter consists of WDG_LOAD_LOW and WDG_LOAD_HIGH,
which would be loaded to watchdog counter once writing WDG_LOAD_LOW.
Fixes: ac17750120 ("spi: sprd: Add the support of restarting the system")
Signed-off-by: Lingling Xu <ling_ling.xu@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20200602082415.5848-1-zhang.lyra@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ColdFire is a big-endian cpu with a big-endian dspi hw module,
so, it uses native access, but memcpy breaks the endianness.
So, if i understand properly, by native copy we would mean
be(cpu)->be(dspi) or le(cpu)->le(dspi) accesses, so my fix
shouldn't break anything, but i couldn't test it on LS family,
so every test is really appreciated.
Fixes: 53fadb4d90 ("spi: spi-fsl-dspi: Simplify bytes_per_word gymnastics")
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200529195756.184677-1-angelo.dureghello@timesys.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It's better to understand what bits are set for DMA and for IRQ handling
in mid_spi_dma_setup() if they are grouped accordingly. Thus,
refactor mid_spi_dma_setup() to separate DMA and IRQ configuration.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200529183150.44149-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The 2afccbd283 ("spi: dw: Discard static DW DMA slave structures")
did a clean up of global variables, which is fine, but messed up with
the carefully provided information in the custom DMA slave structures.
There reader can find an assignment of the DMA request lines in use.
Partially revert the above mentioned commit to restore readability
and maintainability of the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200529183150.44149-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit ecfbd3cf3b since Lukas Wunner noticed that we
start operating on the hardware before we check to see if this is a
spurious interrupt.
Reported-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Baikal-T1 SoC provides a DW DMA controller to perform low-speed peripherals
Mem-to-Dev and Dev-to-Mem transaction. This is also applicable to the DW
APB SSI devices embedded into the SoC. Currently the DMA-based transfers
are supported by the DW APB SPI driver only as a middle layer code for
Intel MID/Elkhart PCI devices. Seeing the same code can be used for normal
platform DMAC device we introduced a set of patches to fix it within this
series.
First of all we need to add the Tx and Rx DMA channels support into the DW
APB SSI binding. Then there are several fixes and cleanups provided as a
initial preparation for the Generic DMA support integration: add Tx/Rx
finish wait methods, clear DMAC register when done or stopped, Fix native
CS being unset, enable interrupts in accordance with DMA xfer mode,
discard static DW DMA slave structures, discard unused void priv pointer
and dma_width member of the dw_spi structure, provide the DMA Tx/Rx burst
length parametrisation and make sure it's optionally set in accordance
with the DMA max-burst capability.
In order to have the DW APB SSI MMIO driver working with DMA we need to
initialize the paddr field with the physical base address of the DW APB SSI
registers space. Then we unpin the Intel MID specific code from the
generic DMA one and placed it into the spi-dw-pci.c driver, which is a
better place for it anyway. After that the naming cleanups are performed
since the code is going to be used for a generic DMAC device. Finally the
Generic DMA initialization can be added to the generic version of the
DW APB SSI IP.
Last but not least we traditionally convert the legacy plain text-based
dt-binding file with yaml-based one and as a cherry on a cake replace
the manually written DebugFS registers read method with a ready-to-use
for the same purpose regset32 DebugFS interface usage.
This patchset is rebased and tested on the spi/for-next (5.7-rc5):
base-commit: fe9fce6b2cf3 ("Merge remote-tracking branch 'spi/for-5.8' into spi-next")
Link: https://lore.kernel.org/linux-spi/20200508132943.9826-1-Sergey.Semin@baikalelectronics.ru/
Changelog v2:
- Rebase on top of the spi repository for-next branch.
- Move bindings conversion patch to the tail of the series.
- Move fixes to the head of the series.
- Apply as many changes as possible to be applied the Generic DMA
functionality support is added and the spi-dw-mid is moved to the
spi-dw-dma driver.
- Discard patch "spi: dw: Fix dma_slave_config used partly uninitialized"
since the problem has already been fixed.
- Add new patch "spi: dw: Discard unused void priv pointer".
- Add new patch "spi: dw: Discard dma_width member of the dw_spi structure".
n_bytes member of the DW SPI data can be used instead.
- Build the DMA functionality into the DW APB SSI core if required instead
of creating a separate kernel module.
- Use conditional statement instead of the ternary operator in the ref
clock getter.
Link: https://lore.kernel.org/linux-spi/20200515104758.6934-1-Sergey.Semin@baikalelectronics.ru/
Changelog v3:
- Use spi_delay_exec() method to wait for the DMA operation completion.
- Explicitly initialize the dw_dma_slave members on stack.
- Discard the dws->fifo_len utilization in the Tx FIFO DMA threshold
setting from the patch where we just add the default burst length
constants.
- Use min() method to calculate the optimal burst values.
- Add new patch which moves the spi-dw.c source file to spi-dw-core.c in
order to preserve the DW APB SSI core driver name.
- Add commas in the debugfs_reg32 structure initializer and after the last
entry of the dw_spi_dbgfs_regs array.
Link: https://lore.kernel.org/linux-spi/20200521012206.14472-1-Sergey.Semin@baikalelectronics.ru
Changelog v4:
- Get back ndelay() method to wait for an SPI transfer completion.
spi_delay_exec() isn't suitable for the atomic context.
Link: https://lore.kernel.org/linux-spi/20200522000806.7381-1-Sergey.Semin@baikalelectronics.ru
Changelog v5:
- Refactor the Tx/Rx DMA-based SPI transfers wait methods.
- Add a new patch "spi: dw: Set xfer effective_speed_hz".
- Add a new patch "spi: dw: Return any value retrieved from the
dma_transfer callback" as a preparation patch before implementing
the local DMA, Tx SPI and Rx SPI transfers wait methods.
- Add a new patch "spi: dw: Locally wait for the DMA transactions
completion", which provides a local DMA transaction complete
method
- Create a dedicated patch which adds the Rx-done wait method:
"spi: dw: Add SPI Rx-done wait method to DMA-based transfer".
- Add more detailed description of the problems the Tx/Rx-wait
methods-related patches fix.
- Wait for the SPI Tx and Rx transfers being finished in the
mid_spi_dma_transfer() method executed in the task context.
- Use spi_delay_exec() to wait for the SPI Tx/Rx completion, since now
the driver calls the wait methods in the kernel thread context.
- Use SPI_DELAY_UNIT_SCK spi_delay unit for Tx-wait delay, since SPI
xfer's are now have the effective_speed_hz initialized.
- Rx-wait for a delay correlated with the APB/SSI synchronous clock
rate instead of using the SPI bus clock rate.
Link: https://lore.kernel.org/linux-spi/20200529035915.20790-1-Sergey.Semin@baikalelectronics.ru
Changelog v6:
- Provide a more detailed description of the patch:
2901db35bea1 ("spi: dw: Locally wait for the DMA transfers completion")
- Calculate the Rx delay with better accuracy by moving 4-multiplication
to the head of the formulae:
ns = 4U * NSEC_PER_SEC / dws->max_freq * nents.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Maxim Kaurkin <Maxim.Kaurkin@baikalelectronics.ru>
Cc: Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru>
Cc: Ekaterina Skachko <Ekaterina.Skachko@baikalelectronics.ru>
Cc: Vadim Vlasov <V.Vlasov@baikalelectronics.ru>
Cc: Alexey Kolotnikov <Alexey.Kolotnikov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-spi@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Serge Semin (16):
spi: dw: Set xfer effective_speed_hz
spi: dw: Return any value retrieved from the dma_transfer callback
spi: dw: Locally wait for the DMA transfers completion
spi: dw: Add SPI Tx-done wait method to DMA-based transfer
spi: dw: Add SPI Rx-done wait method to DMA-based transfer
spi: dw: Parameterize the DMA Rx/Tx burst length
spi: dw: Use DMA max burst to set the request thresholds
spi: dw: Fix Rx-only DMA transfers
spi: dw: Add core suffix to the DW APB SSI core source file
spi: dw: Move Non-DMA code to the DW PCIe-SPI driver
spi: dw: Remove DW DMA code dependency from DW_DMAC_PCI
spi: dw: Add DW SPI DMA/PCI/MMIO dependency on the DW SPI core
spi: dw: Cleanup generic DW DMA code namings
spi: dw: Add DMA support to the DW SPI MMIO driver
spi: dw: Use regset32 DebugFS method to create regdump file
dt-bindings: spi: Convert DW SPI binding to DT schema
.../bindings/spi/snps,dw-apb-ssi.txt | 44 --
.../bindings/spi/snps,dw-apb-ssi.yaml | 127 +++++
.../devicetree/bindings/spi/spi-dw.txt | 24 -
drivers/spi/Kconfig | 15 +-
drivers/spi/Makefile | 5 +-
drivers/spi/{spi-dw.c => spi-dw-core.c} | 95 ++--
drivers/spi/spi-dw-dma.c | 482 ++++++++++++++++++
drivers/spi/spi-dw-mid.c | 382 --------------
drivers/spi/spi-dw-mmio.c | 4 +
drivers/spi/spi-dw-pci.c | 50 +-
drivers/spi/spi-dw.h | 20 +-
11 files changed, 719 insertions(+), 529 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt
create mode 100644 Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml
delete mode 100644 Documentation/devicetree/bindings/spi/spi-dw.txt
rename drivers/spi/{spi-dw.c => spi-dw-core.c} (82%)
create mode 100644 drivers/spi/spi-dw-dma.c
delete mode 100644 drivers/spi/spi-dw-mid.c
--
2.26.2
Add mechanism to get the reset control and deassert it in order to bring
the IP out of reset.
Signed-off-by: Liang Jin J <liang.j.jin@ericsson.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Link: https://lore.kernel.org/r/20200529155806.16758-1-dinguyen@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
bcm2711, Rasberry Pi 4's SoC, shares one interrupt for multiple
instances of the bcm2835 SPI controller. So this enables shared
interrupt support for them.
The early bail out in the interrupt routine avoids messing with buffers
of transfers being done by other means. Otherwise, the driver can handle
receiving interrupts asserted by other controllers during an IRQ based
transfer.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200528185805.28991-1-nsaenzjulienne@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the common code in the spi-dw-dma.c driver is ready to be used
by the MMIO driver and now provides a method to generically (on any
DT or ACPI-based platforms) retrieve the Tx/Rx DMA channel handlers,
we can use it and a set of the common DW SPI DMA callbacks to enable
DMA at least for generic "snps,dw-apb-ssi" and "snps,dwc-ssi-1.01a"
devices.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-15-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Since from now the former Intel MID platform layer is used as a generic
DW SPI DMA module, let's alter the internal methods naming to be
DMA-related instead of having the "mid_" prefix.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-14-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Since there is a generic method available to initialize the DW SPI DMA
interface on any DT and ACPI-based platforms, which in general can be
designed with not only DW DMAC but with any DMA engine on board, we can
freely remove the CONFIG_DW_DMAC_PCI config from dependency list of
CONFIG_SPI_DW_DMA. Especially seeing that we don't use anything DW DMAC
specific in the new driver.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-12-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a preparation patch before adding the DW DMA support into the
DW SPI MMIO driver. We need to unpin the Non-DMA-specific code from the
intended to be generic DW APB SSI DMA code. This isn't that hard,
since the most part of the spi-dw-mid.c driver in fact implements a
generic DMA interface for the DW SPI controller driver. The only Intel
MID specifics concern getting the max frequency from the MRST Clock
Control Unit and fetching the DMA controller channels from
corresponding PCIe DMA controller. Since first one is related with the
SPI interface configuration we moved it' implementation into the
DW PCIe-SPI driver module. After that former spi-dw-mid.c file
can be just renamed to be the DW SPI DMA module optionally compiled in to
the DW APB SSI core driver.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-11-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Generic DMA support is going to be part of the DW APB SSI core object.
In order to preserve the kernel loadable module name as spi-dw.ko, let's
add the "-core" suffix to the object with generic DW APB SSI code and
build it into the target spi-dw.ko driver.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-10-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Tx-only DMA transfers are working perfectly fine since in this case
the code just ignores the Rx FIFO overflow interrupts. But it turns
out the SPI Rx-only transfers are broken since nothing pushing any
data to the shift registers, so the Rx FIFO is left empty and the
SPI core subsystems just returns a timeout error. Since DW DMAC
driver doesn't support something like cyclic write operations of
a single byte to a device register, the only way to support the
Rx-only SPI transfers is to fake it by using a dummy Tx-buffer.
This is what we intend to fix in this commit by setting the
SPI_CONTROLLER_MUST_TX flag for DMA-capable platform.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-9-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Each channel of DMA controller may have a limited length of burst
transaction (number of IO operations performed at ones in a single
DMA client request). This parameter can be used to setup the most
optimal DMA Tx/Rx data level values. In order to avoid the Tx buffer
overrun we can set the DMA Tx level to be of FIFO depth minus the
maximum burst transactions length. To prevent the Rx buffer underflow
the DMA Rx level should be set to the maximum burst transactions length.
This commit setups the DMA channels and the DW SPI DMA Tx/Rx levels
in accordance with these rules.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-8-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
It isn't good to have numeric literals in the code especially if there
are multiple of them and they are related. Let's replace the Tx and Rx
burst level literals with the corresponding constants.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-7-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Having any data left in the Rx FIFO after the DMA engine claimed it has
finished all DMA transactions is an abnormal situation, since the DW SPI
controller driver expects to have all the data being fetched and placed
into the SPI Rx buffer at that moment. In case if that has happened we
hopefully assume that the DMA engine may still be doing the data fetching,
thus we give it sometime to finish. If after a short period of time the
data is still left in the Rx FIFO, the driver will give up waiting and
return an error indicating that the SPI controller/DMA engine must have
hung up or failed at some point of doing their duties.
Fixes: 7063c0d942 ("spi/dw_spi: add DMA support")
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-6-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Since DMA transfers are performed asynchronously with actual SPI bus
transfers, then even if DMA transactions are finished it doesn't mean
all data is actually pushed to the SPI bus. Some data might still be
in the controller FIFO. This is specifically true for Tx-only transfers.
In this case if the next SPI transfer is recharged while a tail of the
previous one is still in FIFO, we'll loose that tail data. In order to
fix that problem let's add the wait procedure of the Tx SPI transfer
completion after the DMA transactions are finished.
Fixes: 7063c0d942 ("spi/dw_spi: add DMA support")
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
In general each DMA-based SPI transfer can be split up into two stages:
DMA data transmission/reception and SPI-bus transmission/reception. DMA
asynchronous transactions completion can be tracked by means of the
DMA async Tx-descriptor completion callback. But that callback being
called indicates that the DMA transfer has been finished, it doesn't
mean that SPI data transmission is also done. Moreover in fact it isn't
for at least Tx-only SPI transfers. Upon DMA transfer completion some
data is left in the Tx FIFO and being pushed out by the SPI controller.
So in order to make sure that an SPI transfer is completely pushed to the
SPI-bus, the driver has to wait for both DMA transaction and the SPI-bus
transmission/reception are finished. Note if there is a way to
asynchronously track the former event by means of the DMA async Tx
callback, there isn't easy one for the later (IRQ-based solution won't
work since SPI controller doesn't notify about Rx FIFO being empty).
The DMA transfer completion callback isn't suitable to wait for the
SPI controller activity finish either. The callback might (in case of DW
DMAC it will) be called in the tasklet context. Waiting for the SPI
controller to complete the transfer might take a considerable amount of
time since SPI-bus might be pretty slow. In this case delaying the
execution in the tasklet atomic context might cause significant system
performance drop.
So to speak the best option we've got to solve the problem is to
consequently wait for both stages being finished in the locally
implemented SPI transfer execution procedure even if it costs us of the
local wait-function re-implementation. In this case we don't need to use
the SPI-core transfer-wait functionality, but we'll make sure that
all DMA and SPI-bus transactions are completely finished before the
SPI-core transfer_one callback returns. In this commit we provide an
implementation of the DMA-transfers completion wait functionality.
The DW APB SSI DMA-specific SPI transfer_one function waits for both
Tx and Rx DMA transfers being finished, and only then exits with zero
returned signalling to the SPI core that the SPI transfer is finished.
This implementation is fully equivalent to the currently used
DMA-execution-SPI-core-wait algorithm. The SPI-bus transmission/reception
wait methods will be added in the follow-up commits.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
DW APB SSI DMA-part of the driver may need to perform the requested
SPI-transfer synchronously. In that case the dma_transfer() callback
will return 0 as a marker of the SPI transfer being finished so the
SPI core doesn't need to wait and may proceed with the SPI message
trasnfers pumping procedure. This will be needed to fix the problem
when DMA transactions are finished, but there is still data left in
the SPI Tx/Rx FIFOs being sent/received. But for now make dma_transfer
to return 1 as the normal dw_spi_transfer_one() method.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Seeing DW APB SSI controller doesn't support setting the exactly
requested SPI bus frequency, but only a rounded frequency determined
by means of the odd-numbered half-worded reference clock divider,
it would be good to tune the SPI core up and initialize the current
transfer effective_speed_hz. By doing so the core will be able to
execute the xfer-related delays with better accuracy.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
There is ecspi ERR009165 on i.mx6/7 soc family, which cause FIFO
transfer to be send twice in DMA mode. Please get more information from:
https://www.nxp.com/docs/en/errata/IMX6DQCE.pdf. The workaround is adding
new sdma ram script which works in XCH mode as PIO inside sdma instead
of SMC mode, meanwhile, 'TX_THRESHOLD' should be 0. The issue should be
exist on all legacy i.mx6/7 soc family before i.mx6ul.
NXP fix this design issue from i.mx6ul, so newer chips including i.mx6ul/
6ull/6sll do not need this workaroud anymore. All other i.mx6/7/8 chips
still need this workaroud. This patch set add new 'fsl,imx6ul-ecspi'
for ecspi driver and 'ecspi_fixed' in sdma driver to choose if need errata
or not.
The first two reverted patches should be the same issue, though, it
seems 'fixed' by changing to other shp script. Hope Sean or Sascha could
have the chance to test this patch set if could fix their issues.
Besides, enable sdma support for i.mx8mm/8mq and fix ecspi1 not work
on i.mx8mm because the event id is zero.
PS:
Please get sdma firmware from below linux-firmware and copy it to your
local rootfs /lib/firmware/imx/sdma.
https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/tree/imx/sdma
v2:
1.Add commit log for reverted patches.
2.Add comment for 'ecspi_fixed' in sdma driver.
3.Add 'fsl,imx6sll-ecspi' compatible instead of 'fsl,imx6ul-ecspi'
rather than remove.
v3:
1.Confirm with design team make sure ERR009165 fixed on i.mx6ul/i.mx6ull
/i.mx6sll, not fixed on i.mx8m/8mm and other i.mx6/7 legacy chips.
Correct dts related dts patch in v2.
2.Clean eratta information in binding doc and new 'tx_glitch_fixed' flag
in spi-imx driver to state ERR009165 fixed or not.
3.Enlarge burst size to fifo size for tx since tx_wml set to 0 in the
errata workaroud, thus improve performance as possible.
v4:
1.Add Ack tag from Mark and Vinod
2.Remove checking 'event_id1' zero as 'event_id0'.
v5:
1.Add the last patch for compatible with the current uart driver which
using rom script, so both uart ram script and rom script supported
in latest firmware, by default uart rom script used. UART driver
will be broken without this patch.
v6:
1.Resend after rebase the latest next branch.
2.Remove below No.13~No.15 patches of v5 because they were mergered.
ARM: dts: imx6ul: add dma support on ecspi
ARM: dts: imx6sll: correct sdma compatible
arm64: defconfig: Enable SDMA on i.mx8mq/8mm
3.Revert "dmaengine: imx-sdma: fix context cache" since
'context_loaded' removed.
v7:
1.Put the last patch 13/13 'Revert "dmaengine: imx-sdma: fix context
cache"' to the ahead of 03/13 'Revert "dmaengine: imx-sdma: refine
to load context only once" so that no building waring during comes out
during bisect.
2.Address Sascha's comments, including eliminating any i.mx6sx in this
series, adding new 'is_imx6ul_ecspi()' instead imx in imx51 and taking
care SMC bit for PIO.
3.Add back missing 'Reviewed-by' tag on 08/15(v5):09/13(v7)
'spi: imx: add new i.mx6ul compatible name in binding doc'
v8:
1.remove 0003-Revert-dmaengine-imx-sdma-fix-context-cache.patch and merge
it into 04/13 of v7
2.add 0005-spi-imx-fallback-to-PIO-if-dma-setup-failure.patch for no any
ecspi function broken even if sdma firmware not updated.
3.merge 'tx.dst_maxburst' changes in the two continous patches into one
patch to avoid confusion.
4.fix typo 'duplicated'.
Robin Gong (13):
Revert "ARM: dts: imx6q: Use correct SDMA script for SPI5 core"
Revert "ARM: dts: imx6: Use correct SDMA script for SPI cores"
Revert "dmaengine: imx-sdma: refine to load context only once"
dmaengine: imx-sdma: remove duplicated sdma_load_context
spi: imx: fallback to PIO if dma setup failure
dmaengine: imx-sdma: add mcu_2_ecspi script
spi: imx: fix ERR009165
spi: imx: remove ERR009165 workaround on i.mx6ul
spi: imx: add new i.mx6ul compatible name in binding doc
dmaengine: imx-sdma: remove ERR009165 on i.mx6ul
dma: imx-sdma: add i.mx6ul compatible name
dmaengine: imx-sdma: fix ecspi1 rx dma not work on i.mx8mm
dmaengine: imx-sdma: add uart rom script
.../devicetree/bindings/dma/fsl-imx-sdma.txt | 1 +
.../devicetree/bindings/spi/fsl-imx-cspi.txt | 1 +
arch/arm/boot/dts/imx6q.dtsi | 2 +-
arch/arm/boot/dts/imx6qdl.dtsi | 8 +-
drivers/dma/imx-sdma.c | 67 ++++++++++------
drivers/spi/spi-imx.c | 92 +++++++++++++++++++---
include/linux/platform_data/dma-imx-sdma.h | 8 +-
7 files changed, 135 insertions(+), 44 deletions(-)
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20200523124758.28604-1-dinghao.liu@zju.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20200523122909.25247-1-dinghao.liu@zju.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20200523125704.30300-1-dinghao.liu@zju.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Fallback to PIO in case dma setup failed. For example, sdma firmware not
updated but ERR009165 workaroud added in kernel.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/1590006865-20900-6-git-send-email-yibin.gong@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20200523133859.5625-1-dinghao.liu@zju.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
