Make it available to AMD hosts as well, just in case someone is trying
to use an Intel processor's CPUID setup.
Suggested-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is an imperfection in get_vmx_mem_address(): access length is ignored
when checking the limit. To fix this, pass access length as a function argument.
The access length is usually obvious since it is used by callers after
get_vmx_mem_address() call, but for vmread/vmwrite it depends on the
state of 64-bit mode.
Signed-off-by: Eugene Korenevsky <ekorenevsky@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Intel SDM vol. 3, 5.3:
The processor causes a
general-protection exception (or, if the segment is SS, a stack-fault
exception) any time an attempt is made to access the following addresses
in a segment:
- A byte at an offset greater than the effective limit
- A word at an offset greater than the (effective-limit – 1)
- A doubleword at an offset greater than the (effective-limit – 3)
- A quadword at an offset greater than the (effective-limit – 7)
Therefore, the generic limit checking error condition must be
exn = (off > limit + 1 - access_len) = (off + access_len - 1 > limit)
but not
exn = (off + access_len > limit)
as for now.
Also avoid integer overflow of `off` at 32-bit KVM by casting it to u64.
Note: access length is currently sizeof(u64) which is incorrect. This
will be fixed in the subsequent patch.
Signed-off-by: Eugene Korenevsky <ekorenevsky@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make all code consistent with kvm_deliver_exception_payload() by using
appropriate symbolic constant instead of hard-coded number.
Reviewed-by: Nikita Leshenko <nikita.leshchenko@oracle.com>
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Unfortunately, a couple of mistakes were made while implementing
Enlightened VMCS support, in particular, wrong clean fields were
used in copy_enlightened_to_vmcs12():
- exception_bitmap is covered by CONTROL_EXCPN;
- vm_exit_controls/pin_based_vm_exec_control/secondary_vm_exec_control
are covered by CONTROL_GRP1.
Fixes: 945679e301 ("KVM: nVMX: add enlightened VMCS state")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
__vmcs_writel uses volatile asm, so there is no need to insert another
one between the first and the second call to __vmcs_writel in order
to prevent unwanted code moves for 32bit targets.
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
While upstream gcc doesn't detect conflicts on cc (yet), it really
should, and hence "cc" should not be specified for asm()-s also having
"=@cc<cond>" outputs. (It is quite pointless anyway to specify a "cc"
clobber in x86 inline assembly, since the compiler assumes it to be
always clobbered, and has no means [yet] to suppress this behavior.)
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Fixes: bbc0b82392 ("KVM: nVMX: Capture VM-Fail via CC_{SET,OUT} in nested early checks")
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Allow guest reads CORE cstate when exposing host CPU power management capabilities
to the guest. PKG cstate is restricted to avoid a guest to get the whole package
information in multi-tenant scenario.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Sean Christopherson <sean.j.christopherson@intel.com>
Cc: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a wrapper to invoke kvm_arch_check_processor_compat() so that the
boilerplate ugliness of checking virtualization support on all CPUs is
hidden from the arch specific code. x86's implementation in particular
is quite heinous, as it unnecessarily propagates the out-param pattern
into kvm_x86_ops.
While the x86 specific issue could be resolved solely by changing
kvm_x86_ops, make the change for all architectures as returning a value
directly is prettier and technically more robust, e.g. s390 doesn't set
the out param, which could lead to subtle breakage in the (highly
unlikely) scenario where the out-param was not pre-initialized by the
caller.
Opportunistically annotate svm_check_processor_compat() with __init.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Advance lapic timer tries to hidden the hypervisor overhead between the
host emulated timer fires and the guest awares the timer is fired. However,
it just hidden the time between apic_timer_fn/handle_preemption_timer ->
wait_lapic_expire, instead of the real position of vmentry which is
mentioned in the orignial commit d0659d946b ("KVM: x86: add option to
advance tscdeadline hrtimer expiration"). There is 700+ cpu cycles between
the end of wait_lapic_expire and before world switch on my haswell desktop.
This patch tries to narrow the last gap(wait_lapic_expire -> world switch),
it takes the real overhead time between apic_timer_fn/handle_preemption_timer
and before world switch into consideration when adaptively tuning timer
advancement. The patch can reduce 40% latency (~1600+ cycles to ~1000+ cycles
on a haswell desktop) for kvm-unit-tests/tscdeadline_latency when testing
busy waits.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Sean Christopherson <sean.j.christopherson@intel.com>
Cc: Liran Alon <liran.alon@oracle.com>
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
According to the SDM, for MSR_IA32_PERFCTR0/1 "the lower-order 32 bits of
each MSR may be written with any value, and the high-order 8 bits are
sign-extended according to the value of bit 31", but the fixed counters
in real hardware are limited to the width of the fixed counters ("bits
beyond the width of the fixed-function counter are reserved and must be
written as zeros"). Fix KVM to do the same.
Reported-by: Nadav Amit <nadav.amit@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch will simplify the changes in the next, by enforcing the
masking of the counters to RDPMC and RDMSR.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Userspace can easily set up invalid processor state in such a way that
dmesg will be filled with VMCS or VMCB dumps. Disable this by default
using a module parameter.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We get a warning when build kernel W=1:
arch/x86/kvm/vmx/vmx.c:6365:6: warning: no previous prototype for ‘vmx_update_host_rsp’ [-Wmissing-prototypes]
void vmx_update_host_rsp(struct vcpu_vmx *vmx, unsigned long host_rsp)
Add the missing declaration to fix this.
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VMX's nested_run_pending flag is subtly consumed when stuffing state to
enter guest mode, i.e. needs to be set according before KVM knows if
setting guest state is successful. If setting guest state fails, clear
the flag as a nested run is obviously not pending.
Reported-by: Aaron Lewis <aaronlewis@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The offset for reading the shadow VMCS is sizeof(*kvm_state)+VMCS12_SIZE,
so the correct size must be that plus sizeof(*vmcs12). This could lead
to KVM reading garbage data from userspace and not reporting an error,
but is otherwise not sensitive.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* POWER: support for direct access to the POWER9 XIVE interrupt controller,
memory and performance optimizations.
* x86: support for accessing memory not backed by struct page, fixes and refactoring
* Generic: dirty page tracking improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJc3qV/AAoJEL/70l94x66Dn3QH/jX1Bn0P/RZAIt4w0SySklSg
PqxUKDyBQqB9vN9Qeb9jWXAKPH2CtM3+up/rz7oRnBWp7qA6vXcC/R/QJYAvzdXE
nklsR/oYCsflR1KdlVYuDvvPCPP2fLBU5zfN83OsaBQ8fNRkm3gN+N5XQ2SbXbLy
Mo9tybS4otY201UAC96e8N0ipwwyCRpDneQpLcl+F5nH3RBt63cVbs04O+70MXn7
eT4I+8K3+Go7LATzT8hglD21D/7uvE31qQb6yr5L33IfhU4GB51RZzBXTNaAdY8n
hT1rMrRkAMAFWYZPQDfoMadjWU3i5DIfstKjDxOr9oTfuOEp5Z+GvJwvVnUDg1I=
=D0+p
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"ARM:
- support for SVE and Pointer Authentication in guests
- PMU improvements
POWER:
- support for direct access to the POWER9 XIVE interrupt controller
- memory and performance optimizations
x86:
- support for accessing memory not backed by struct page
- fixes and refactoring
Generic:
- dirty page tracking improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (155 commits)
kvm: fix compilation on aarch64
Revert "KVM: nVMX: Expose RDPMC-exiting only when guest supports PMU"
kvm: x86: Fix L1TF mitigation for shadow MMU
KVM: nVMX: Disable intercept for FS/GS base MSRs in vmcs02 when possible
KVM: PPC: Book3S: Remove useless checks in 'release' method of KVM device
KVM: PPC: Book3S HV: XIVE: Fix spelling mistake "acessing" -> "accessing"
KVM: PPC: Book3S HV: Make sure to load LPID for radix VCPUs
kvm: nVMX: Set nested_run_pending in vmx_set_nested_state after checks complete
tests: kvm: Add tests for KVM_SET_NESTED_STATE
KVM: nVMX: KVM_SET_NESTED_STATE - Tear down old EVMCS state before setting new state
tests: kvm: Add tests for KVM_CAP_MAX_VCPUS and KVM_CAP_MAX_CPU_ID
tests: kvm: Add tests to .gitignore
KVM: Introduce KVM_CAP_MANUAL_DIRTY_LOG_PROTECT2
KVM: Fix kvm_clear_dirty_log_protect off-by-(minus-)one
KVM: Fix the bitmap range to copy during clear dirty
KVM: arm64: Fix ptrauth ID register masking logic
KVM: x86: use direct accessors for RIP and RSP
KVM: VMX: Use accessors for GPRs outside of dedicated caching logic
KVM: x86: Omit caching logic for always-available GPRs
kvm, x86: Properly check whether a pfn is an MMIO or not
...
The RDPMC-exiting control is dependent on the existence of the RDPMC
instruction itself, i.e. is not tied to the "Architectural Performance
Monitoring" feature. For all intents and purposes, the control exists
on all CPUs with VMX support since RDPMC also exists on all VCPUs with
VMX supported. Per Intel's SDM:
The RDPMC instruction was introduced into the IA-32 Architecture in
the Pentium Pro processor and the Pentium processor with MMX technology.
The earlier Pentium processors have performance-monitoring counters, but
they must be read with the RDMSR instruction.
Because RDPMC-exiting always exists, KVM requires the control and refuses
to load if it's not available. As a result, hiding the PMU from a guest
breaks nested virtualization if the guest attemts to use KVM.
While it's not explicitly stated in the RDPMC pseudocode, the VM-Exit
check for RDPMC-exiting follows standard fault vs. VM-Exit prioritization
for privileged instructions, e.g. occurs after the CPL/CR0.PE/CR4.PCE
checks, but before the counter referenced in ECX is checked for validity.
In other words, the original KVM behavior of injecting a #GP was correct,
and the KVM unit test needs to be adjusted accordingly, e.g. eat the #GP
when the unit test guest (L3 in this case) executes RDPMC without
RDPMC-exiting set in the unit test host (L2).
This reverts commit e51bfdb687.
Fixes: e51bfdb687 ("KVM: nVMX: Expose RDPMC-exiting only when guest supports PMU")
Reported-by: David Hill <hilld@binarystorm.net>
Cc: Saar Amar <saaramar@microsoft.com>
Cc: Mihai Carabas <mihai.carabas@oracle.com>
Cc: Jim Mattson <jmattson@google.com>
Cc: Liran Alon <liran.alon@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If L1 is using an MSR bitmap, unconditionally merge the MSR bitmaps from
L0 and L1 for MSR_{KERNEL,}_{FS,GS}_BASE. KVM unconditionally exposes
MSRs L1. If KVM is also running in L1 then it's highly likely L1 is
also exposing the MSRs to L2, i.e. KVM doesn't need to intercept L2
accesses.
Based on code from Jintack Lim.
Cc: Jintack Lim <jintack@xxxxxxxxxxxxxxx>
Signed-off-by: Sean Christopherson <sean.j.christopherson@xxxxxxxxx>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pull x86 MDS mitigations from Thomas Gleixner:
"Microarchitectural Data Sampling (MDS) is a hardware vulnerability
which allows unprivileged speculative access to data which is
available in various CPU internal buffers. This new set of misfeatures
has the following CVEs assigned:
CVE-2018-12126 MSBDS Microarchitectural Store Buffer Data Sampling
CVE-2018-12130 MFBDS Microarchitectural Fill Buffer Data Sampling
CVE-2018-12127 MLPDS Microarchitectural Load Port Data Sampling
CVE-2019-11091 MDSUM Microarchitectural Data Sampling Uncacheable Memory
MDS attacks target microarchitectural buffers which speculatively
forward data under certain conditions. Disclosure gadgets can expose
this data via cache side channels.
Contrary to other speculation based vulnerabilities the MDS
vulnerability does not allow the attacker to control the memory target
address. As a consequence the attacks are purely sampling based, but
as demonstrated with the TLBleed attack samples can be postprocessed
successfully.
The mitigation is to flush the microarchitectural buffers on return to
user space and before entering a VM. It's bolted on the VERW
instruction and requires a microcode update. As some of the attacks
exploit data structures shared between hyperthreads, full protection
requires to disable hyperthreading. The kernel does not do that by
default to avoid breaking unattended updates.
The mitigation set comes with documentation for administrators and a
deeper technical view"
* 'x86-mds-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
x86/speculation/mds: Fix documentation typo
Documentation: Correct the possible MDS sysfs values
x86/mds: Add MDSUM variant to the MDS documentation
x86/speculation/mds: Add 'mitigations=' support for MDS
x86/speculation/mds: Print SMT vulnerable on MSBDS with mitigations off
x86/speculation/mds: Fix comment
x86/speculation/mds: Add SMT warning message
x86/speculation: Move arch_smt_update() call to after mitigation decisions
x86/speculation/mds: Add mds=full,nosmt cmdline option
Documentation: Add MDS vulnerability documentation
Documentation: Move L1TF to separate directory
x86/speculation/mds: Add mitigation mode VMWERV
x86/speculation/mds: Add sysfs reporting for MDS
x86/speculation/mds: Add mitigation control for MDS
x86/speculation/mds: Conditionally clear CPU buffers on idle entry
x86/kvm/vmx: Add MDS protection when L1D Flush is not active
x86/speculation/mds: Clear CPU buffers on exit to user
x86/speculation/mds: Add mds_clear_cpu_buffers()
x86/kvm: Expose X86_FEATURE_MD_CLEAR to guests
x86/speculation/mds: Add BUG_MSBDS_ONLY
...
nested_run_pending=1 implies we have successfully entered guest mode.
Move setting from external state in vmx_set_nested_state() until after
all other checks are complete.
Based on a patch by Aaron Lewis.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move call to nested_enable_evmcs until after free_nested() is complete.
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Reviewed-by: Marc Orr <marcorr@google.com>
Reviewed-by: Peter Shier <pshier@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pull x86 FPU state handling updates from Borislav Petkov:
"This contains work started by Rik van Riel and brought to fruition by
Sebastian Andrzej Siewior with the main goal to optimize when to load
FPU registers: only when returning to userspace and not on every
context switch (while the task remains in the kernel).
In addition, this optimization makes kernel_fpu_begin() cheaper by
requiring registers saving only on the first invocation and skipping
that in following ones.
What is more, this series cleans up and streamlines many aspects of
the already complex FPU code, hopefully making it more palatable for
future improvements and simplifications.
Finally, there's a __user annotations fix from Jann Horn"
* 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (29 commits)
x86/fpu: Fault-in user stack if copy_fpstate_to_sigframe() fails
x86/pkeys: Add PKRU value to init_fpstate
x86/fpu: Restore regs in copy_fpstate_to_sigframe() in order to use the fastpath
x86/fpu: Add a fastpath to copy_fpstate_to_sigframe()
x86/fpu: Add a fastpath to __fpu__restore_sig()
x86/fpu: Defer FPU state load until return to userspace
x86/fpu: Merge the two code paths in __fpu__restore_sig()
x86/fpu: Restore from kernel memory on the 64-bit path too
x86/fpu: Inline copy_user_to_fpregs_zeroing()
x86/fpu: Update xstate's PKRU value on write_pkru()
x86/fpu: Prepare copy_fpstate_to_sigframe() for TIF_NEED_FPU_LOAD
x86/fpu: Always store the registers in copy_fpstate_to_sigframe()
x86/entry: Add TIF_NEED_FPU_LOAD
x86/fpu: Eager switch PKRU state
x86/pkeys: Don't check if PKRU is zero before writing it
x86/fpu: Only write PKRU if it is different from current
x86/pkeys: Provide *pkru() helpers
x86/fpu: Use a feature number instead of mask in two more helpers
x86/fpu: Make __raw_xsave_addr() use a feature number instead of mask
x86/fpu: Add an __fpregs_load_activate() internal helper
...
The size checks in vmx_nested_state are wrong because the calculations
are made based on the size of a pointer to a struct kvm_nested_state
rather than the size of a struct kvm_nested_state.
Reported-by: Felix Wilhelm <fwilhelm@google.com>
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Drew Schmitt <dasch@google.com>
Reviewed-by: Marc Orr <marcorr@google.com>
Reviewed-by: Peter Shier <pshier@google.com>
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Fixes: 8fcc4b5923
Cc: stable@ver.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use specific inline functions for RIP and RSP instead of
going through kvm_register_read and kvm_register_write,
which are quite a mouthful. kvm_rsp_read and kvm_rsp_write
did not exist, so add them.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
... now that there is no overhead when using dedicated accessors.
Opportunistically remove a bogus "FIXME" in handle_rdmsr() regarding
the upper 32 bits of RAX and RDX. Zeroing the upper 32 bits is
architecturally correct as 32-bit writes in 64-bit mode unconditionally
clear the upper 32 bits.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Except for RSP and RIP, which are held in VMX's VMCS, GPRs are always
treated "available and dirtly" on both VMX and SVM, i.e. are
unconditionally loaded/saved immediately before/after VM-Enter/VM-Exit.
Eliminating the unnecessary caching code reduces the size of KVM by a
non-trivial amount, much of which comes from the most common code paths.
E.g. on x86_64, kvm_emulate_cpuid() is reduced from 342 to 182 bytes and
kvm_emulate_hypercall() from 1362 to 1143, with the total size of KVM
dropping by ~1000 bytes. With CONFIG_RETPOLINE=y, the numbers are even
more pronounced, e.g.: 353->182, 1418->1172 and well over 2000 bytes.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use page_address_valid in a few more locations that is already checking for
a page aligned address that does not cross the maximum physical address.
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use kvm_vcpu_map for accessing the enlightened VMCS since using
kvm_vcpu_gpa_to_page() and kmap() will only work for guest memory that has
a "struct page".
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use kvm_vcpu_map for accessing the shadow VMCS since using
kvm_vcpu_gpa_to_page() and kmap() will only work for guest memory that has
a "struct page".
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
Reviewed-by: Konrad Rzessutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use kvm_vcpu_map when mapping the posted interrupt descriptor table since
using kvm_vcpu_gpa_to_page() and kmap() will only work for guest memory
that has a "struct page".
One additional semantic change is that the virtual host mapping lifecycle
has changed a bit. It now has the same lifetime of the pinning of the
interrupt descriptor table page on the host side.
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use kvm_vcpu_map when mapping the virtual APIC page since using
kvm_vcpu_gpa_to_page() and kmap() will only work for guest memory that has
a "struct page".
One additional semantic change is that the virtual host mapping lifecycle
has changed a bit. It now has the same lifetime of the pinning of the
virtual APIC page on the host side.
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use kvm_vcpu_map when mapping the L1 MSR bitmap since using
kvm_vcpu_gpa_to_page() and kmap() will only work for guest memory that has
a "struct page".
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use kvm_vcpu_map to the map the VMCS12 from guest memory because
kvm_vcpu_gpa_to_page() and kmap() will only work for guest memory that has
a "struct page".
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Update the PML table without mapping and unmapping the page. This also
avoids using kvm_vcpu_gpa_to_page(..) which assumes that there is a "struct
page" for guest memory.
As a side-effect of using kvm_write_guest_page the page is also properly
marked as dirty.
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Read the data directly from guest memory instead of the map->read->unmap
sequence. This also avoids using kvm_vcpu_gpa_to_page() and kmap() which
assumes that there is a "struct page" for guest memory.
Suggested-by: Jim Mattson <jmattson@google.com>
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
Reviewed-by: Jim Mattson <jmattson@google.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The capabilities header depends on asm/vmx.h but doesn't explicitly
include said file. This currently doesn't cause problems as all users
of capbilities.h first include asm/vmx.h, but the issue often results in
build errors if someone starts moving things around the VMX files.
Fixes: 3077c19108 ("KVM: VMX: Move capabilities structs and helpers to dedicated file")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Smatch complains about this:
arch/x86/kvm/vmx/vmx.c:5730 dump_vmcs()
warn: KERN_* level not at start of string
The code should be using pr_cont() instead of pr_err().
Fixes: 9d609649bb ("KVM: vmx: print more APICv fields in dump_vmcs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Ten percent of nothin' is... let me do the math here. Nothin' into
nothin', carry the nothin'...
Cc: Wanpeng Li <wanpengli@tencent.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Refactor kvm_x86_ops->set_hv_timer to use an explicit parameter for
stating that the timer has expired. Overloading the return value is
unnecessarily clever, e.g. can lead to confusion over the proper return
value from start_hv_timer() when r==1.
Cc: Wanpeng Li <wanpengli@tencent.com>
Cc: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since commits 668fffa3f8 ("kvm: better MWAIT emulation for guestsâ€)
and 4d5422cea3 ("KVM: X86: Provide a capability to disable MWAIT interceptsâ€),
KVM was modified to allow an admin to configure certain guests to execute
MONITOR/MWAIT inside guest without being intercepted by host.
This is useful in case admin wishes to allocate a dedicated logical
processor for each vCPU thread. Thus, making it safe for guest to
completely control the power-state of the logical processor.
The ability to use this new KVM capability was introduced to QEMU by
commits 6f131f13e68d ("kvm: support -overcommit cpu-pm=on|offâ€) and
2266d4431132 ("i386/cpu: make -cpu host support monitor/mwaitâ€).
However, exposing MONITOR/MWAIT to a Linux guest may cause it's intel_idle
kernel module to execute c1e_promotion_disable() which will attempt to
RDMSR/WRMSR from/to MSR_IA32_POWER_CTL to manipulate the "C1E Enable"
bit. This behaviour was introduced by commit
32e9518005 ("intel_idle: export both C1 and C1Eâ€).
Becuase KVM doesn't emulate this MSR, running KVM with ignore_msrs=0
will cause the above guest behaviour to raise a #GP which will cause
guest to kernel panic.
Therefore, add support for nop emulation of MSR_IA32_POWER_CTL to
avoid #GP in guest in this scenario.
Future commits can optimise emulation further by reflecting guest
MSR changes to host MSR to provide guest with the ability to
fine-tune the dedicated logical processor power-state.
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Let guests clear the Intel PT ToPA PMI status (bit 55 of
MSR_CORE_PERF_GLOBAL_OVF_CTRL).
Signed-off-by: Luwei Kang <luwei.kang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The not-so-recent change to move VMX's VM-Exit handing to a dedicated
"function" unintentionally exposed KVM to a speculative attack from the
guest by executing a RET prior to stuffing the RSB. Make RSB stuffing
happen immediately after VM-Exit, before any unpaired returns.
Alternatively, the VM-Exit path could postpone full RSB stuffing until
its current location by stuffing the RSB only as needed, or by avoiding
returns in the VM-Exit path entirely, but both alternatives are beyond
ugly since vmx_vmexit() has multiple indirect callers (by way of
vmx_vmenter()). And putting the RSB stuffing immediately after VM-Exit
makes it much less likely to be re-broken in the future.
Note, the cost of PUSH/POP could be avoided in the normal flow by
pairing the PUSH RAX with the POP RAX in __vmx_vcpu_run() and adding an
a POP to nested_vmx_check_vmentry_hw(), but such a weird/subtle
dependency is likely to cause problems in the long run, and PUSH/POP
will take all of a few cycles, which is peanuts compared to the number
of cycles required to fill the RSB.
Fixes: 453eafbe65 ("KVM: VMX: Move VM-Enter + VM-Exit handling to non-inline sub-routines")
Reported-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Co-developed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Automatically adjusting the globally-shared timer advancement could
corrupt the timer, e.g. if multiple vCPUs are concurrently adjusting
the advancement value. That could be partially fixed by using a local
variable for the arithmetic, but it would still be susceptible to a
race when setting timer_advance_adjust_done.
And because virtual_tsc_khz and tsc_scaling_ratio are per-vCPU, the
correct calibration for a given vCPU may not apply to all vCPUs.
Furthermore, lapic_timer_advance_ns is marked __read_mostly, which is
effectively violated when finding a stable advancement takes an extended
amount of timer.
Opportunistically change the definition of lapic_timer_advance_ns to
a u32 so that it matches the style of struct kvm_timer. Explicitly
pass the param to kvm_create_lapic() so that it doesn't have to be
exposed to lapic.c, thus reducing the probability of unintentionally
using the global value instead of the per-vCPU value.
Cc: Liran Alon <liran.alon@oracle.com>
Cc: Wanpeng Li <wanpengli@tencent.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Cc: stable@vger.kernel.org
Fixes: 3b8a5df6c4 ("KVM: LAPIC: Tune lapic_timer_advance_ns automatically")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Most, but not all, helpers that are related to emulating consistency
checks for nested VM-Entry return -EINVAL when a check fails. Convert
the holdouts to have consistency throughout and to make it clear that
the functions are signaling pass/fail as opposed to "resume guest" vs.
"exit to userspace".
Opportunistically fix bad indentation in nested_vmx_check_guest_state().
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert all top-level nested VM-Enter consistency check functions to
return 0/-EINVAL instead of failure codes, since now they can only
ever return one failure code.
This also does not give the false impression that failure information is
always consumed and/or relevant, e.g. vmx_set_nested_state() only
cares whether or not the checks were successful.
nested_check_host_control_regs() can also now be inlined into its caller,
nested_vmx_check_host_state, since the two have effectively become the
same function.
Based on a patch by Sean Christopherson.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rename the top-level consistency check functions to (loosely) align with
the SDM. Historically, KVM has used the terms "prereq" and "postreq" to
differentiate between consistency checks that lead to VM-Fail and those
that lead to VM-Exit. The terms are vague and potentially misleading,
e.g. "postreq" might be interpreted as occurring after VM-Entry.
Note, while the SDM lumps controls and host state into a single section,
"Checks on VMX Controls and Host-State Area", split them into separate
top-level functions as the two categories of checks result in different
VM instruction errors. This split will allow for additional cleanup.
Note #2, "vmentry" is intentionally dropped from the new function names
to avoid confusion with nested_check_vm_entry_controls(), and to keep
the length of the functions names somewhat manageable.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Per Intel's SDM, volume 3, section Checking and Loading Guest State:
Because the checking and the loading occur concurrently, a failure may
be discovered only after some state has been loaded. For this reason,
the logical processor responds to such failures by loading state from
the host-state area, as it would for a VM exit.
In other words, a failed non-register state consistency check results in
a VM-Exit, not VM-Fail. Moving the non-reg state checks also paves the
way for renaming nested_vmx_check_vmentry_postreqs() to align with the
SDM, i.e. nested_vmx_check_vmentry_guest_state().
Fixes: 26539bd0e4 ("KVM: nVMX: check vmcs12 for valid activity state")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
According to section "Checking and Loading Guest State" in Intel SDM vol
3C, the following check is performed on vmentry:
If the "load IA32_PAT" VM-entry control is 1, the value of the field
for the IA32_PAT MSR must be one that could be written by WRMSR
without fault at CPL 0. Specifically, each of the 8 bytes in the
field must have one of the values 0 (UC), 1 (WC), 4 (WT), 5 (WP),
6 (WB), or 7 (UC-).
Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Reviewed-by: Karl Heubaum <karl.heubaum@oracle.com>
Suggested-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
According to section "Checks on Host Control Registers and MSRs" in Intel
SDM vol 3C, the following check is performed on vmentry:
If the "load IA32_PAT" VM-exit control is 1, the value of the field
for the IA32_PAT MSR must be one that could be written by WRMSR
without fault at CPL 0. Specifically, each of the 8 bytes in the
field must have one of the values 0 (UC), 1 (WC), 4 (WT), 5 (WP),
6 (WB), or 7 (UC-).
Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Reviewed-by: Karl Heubaum <karl.heubaum@oracle.com>
Suggested-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This check will soon be done on every nested vmentry and vmexit,
"parallelize" it using bitwise operations.
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is not needed, PAT writes always take an MSR vmexit.
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The SVI, RVI, virtual-APIC page address and APIC-access page address fields
were left out of dump_vmcs. Add them.
KERN_CONT technically isn't SMP safe, but it's okay to use it here since
the whole of dump_vmcs() is a single huge multi-line piece of output
that isn't SMP-safe.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
RSM emulation is currently broken on VMX when the interrupted guest has
CR4.VMXE=1. Stop dancing around the issue of HF_SMM_MASK being set when
loading SMSTATE into architectural state, e.g. by toggling it for
problematic flows, and simply clear HF_SMM_MASK prior to loading
architectural state (from SMRAM save state area).
Reported-by: Jon Doron <arilou@gmail.com>
Cc: Jim Mattson <jmattson@google.com>
Cc: Liran Alon <liran.alon@oracle.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Fixes: 5bea5123cb ("KVM: VMX: check nested state and CR4.VMXE against SMM")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Tested-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
RSM emulation is currently broken on VMX when the interrupted guest has
CR4.VMXE=1. Rather than dance around the issue of HF_SMM_MASK being set
when loading SMSTATE into architectural state, ideally RSM emulation
itself would be reworked to clear HF_SMM_MASK prior to loading non-SMM
architectural state.
Ostensibly, the only motivation for having HF_SMM_MASK set throughout
the loading of state from the SMRAM save state area is so that the
memory accesses from GET_SMSTATE() are tagged with role.smm. Load
all of the SMRAM save state area from guest memory at the beginning of
RSM emulation, and load state from the buffer instead of reading guest
memory one-by-one.
This paves the way for clearing HF_SMM_MASK prior to loading state,
and also aligns RSM with the enter_smm() behavior, which fills a
buffer and writes SMRAM save state in a single go.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Issue was discovered when running kvm-unit-tests on KVM running as L1 on
top of Hyper-V.
When vmx_instruction_intercept unit-test attempts to run RDPMC to test
RDPMC-exiting, it is intercepted by L1 KVM which it's EXIT_REASON_RDPMC
handler raise #GP because vCPU exposed by Hyper-V doesn't support PMU.
Instead of unit-test expectation to be reflected with EXIT_REASON_RDPMC.
The reason vmx_instruction_intercept unit-test attempts to run RDPMC
even though Hyper-V doesn't support PMU is because L1 expose to L2
support for RDPMC-exiting. Which is reasonable to assume that is
supported only in case CPU supports PMU to being with.
Above issue can easily be simulated by modifying
vmx_instruction_intercept config in x86/unittests.cfg to run QEMU with
"-cpu host,+vmx,-pmu" and run unit-test.
To handle issue, change KVM to expose RDPMC-exiting only when guest
supports PMU.
Reported-by: Saar Amar <saaramar@microsoft.com>
Reviewed-by: Mihai Carabas <mihai.carabas@oracle.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
guest xcr0 could leak into host when MCE happens in guest mode. Because
do_machine_check() could schedule out at a few places.
For example:
kvm_load_guest_xcr0
...
kvm_x86_ops->run(vcpu) {
vmx_vcpu_run
vmx_complete_atomic_exit
kvm_machine_check
do_machine_check
do_memory_failure
memory_failure
lock_page
In this case, host_xcr0 is 0x2ff, guest vcpu xcr0 is 0xff. After schedule
out, host cpu has guest xcr0 loaded (0xff).
In __switch_to {
switch_fpu_finish
copy_kernel_to_fpregs
XRSTORS
If any bit i in XSTATE_BV[i] == 1 and xcr0[i] == 0, XRSTORS will
generate #GP (In this case, bit 9). Then ex_handler_fprestore kicks in
and tries to reinitialize fpu by restoring init fpu state. Same story as
last #GP, except we get DOUBLE FAULT this time.
Cc: stable@vger.kernel.org
Signed-off-by: WANG Chao <chao.wang@ucloud.cn>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The remaining failures of vmx.flat when EPT is disabled are caused by
incorrectly reflecting VMfails to the L1 hypervisor. What happens is
that nested_vmx_restore_host_state corrupts the guest CR3, reloading it
with the host's shadow CR3 instead, because it blindly loads GUEST_CR3
from the vmcs01.
For simplicity let's just always use hardware VMCS checks when EPT is
disabled. This way, nested_vmx_restore_host_state is not reached at
all (or at least shouldn't be reached).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As mentioned in the comment, there are some special cases where we can simply
clear the TPR shadow bit from the CPU-based execution controls in the vmcs02.
Handle them so that we can remove some XFAILs from vmx.flat.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Dave Hansen asked for __read_pkru() and __write_pkru() to be
symmetrical.
As part of the series __write_pkru() will read back the value and only
write it if it is different.
In order to make both functions symmetrical, move the function
containing only the opcode asm into a function called like the
instruction itself.
__write_pkru() will just invoke wrpkru() but in a follow-up patch will
also read back the value.
[ bp: Convert asm opcode wrapper names to rd/wrpkru(). ]
Suggested-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Dave Hansen <dave.hansen@intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Juergen Gross <jgross@suse.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: kvm ML <kvm@vger.kernel.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190403164156.19645-13-bigeasy@linutronix.de
Referring to the "VIRTUALIZING MSR-BASED APIC ACCESSES" chapter of the
SDM, when "virtualize x2APIC mode" is 1 and "APIC-register
virtualization" is 0, a RDMSR of 808H should return the VTPR from the
virtual APIC page.
However, for nested, KVM currently fails to disable the read intercept
for this MSR. This means that a RDMSR exit takes precedence over
"virtualize x2APIC mode", and KVM passes through L1's TPR to L2,
instead of sourcing the value from L2's virtual APIC page.
This patch fixes the issue by disabling the read intercept, in VMCS02,
for the VTPR when "APIC-register virtualization" is 0.
The issue described above and fix prescribed here, were verified with
a related patch in kvm-unit-tests titled "Test VMX's virtualize x2APIC
mode w/ nested".
Signed-off-by: Marc Orr <marcorr@google.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Fixes: c992384bde ("KVM: vmx: speed up MSR bitmap merge")
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The nested_vmx_prepare_msr_bitmap() function doesn't directly guard the
x2APIC MSR intercepts with the "virtualize x2APIC mode" MSR. As a
result, we discovered the potential for a buggy or malicious L1 to get
access to L0's x2APIC MSRs, via an L2, as follows.
1. L1 executes WRMSR(IA32_SPEC_CTRL, 1). This causes the spec_ctrl
variable, in nested_vmx_prepare_msr_bitmap() to become true.
2. L1 disables "virtualize x2APIC mode" in VMCS12.
3. L1 enables "APIC-register virtualization" in VMCS12.
Now, KVM will set VMCS02's x2APIC MSR intercepts from VMCS12, and then
set "virtualize x2APIC mode" to 0 in VMCS02. Oops.
This patch closes the leak by explicitly guarding VMCS02's x2APIC MSR
intercepts with VMCS12's "virtualize x2APIC mode" control.
The scenario outlined above and fix prescribed here, were verified with
a related patch in kvm-unit-tests titled "Add leak scenario to
virt_x2apic_mode_test".
Note, it looks like this issue may have been introduced inadvertently
during a merge---see 15303ba5d1.
Signed-off-by: Marc Orr <marcorr@google.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The CPUID flag ARCH_CAPABILITIES is unconditioinally exposed to host
userspace for all x86 hosts, i.e. KVM advertises ARCH_CAPABILITIES
regardless of hardware support under the pretense that KVM fully
emulates MSR_IA32_ARCH_CAPABILITIES. Unfortunately, only VMX hosts
handle accesses to MSR_IA32_ARCH_CAPABILITIES (despite KVM_GET_MSRS
also reporting MSR_IA32_ARCH_CAPABILITIES for all hosts).
Move the MSR_IA32_ARCH_CAPABILITIES handling to common x86 code so
that it's emulated on AMD hosts.
Fixes: 1eaafe91a0 ("kvm: x86: IA32_ARCH_CAPABILITIES is always supported")
Cc: stable@vger.kernel.org
Reported-by: Xiaoyao Li <xiaoyao.li@linux.intel.com>
Cc: Jim Mattson <jmattson@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
According to section "Checks on VMX Controls" in Intel SDM vol 3C, the
following check is performed on vmentry of L2 guests:
On processors that support Intel 64 architecture, the IA32_SYSENTER_ESP
field and the IA32_SYSENTER_EIP field must each contain a canonical
address.
Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Reviewed-by: Mihai Carabas <mihai.carabas@oracle.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Errata#1096:
On a nested data page fault when CR.SMAP=1 and the guest data read
generates a SMAP violation, GuestInstrBytes field of the VMCB on a
VMEXIT will incorrectly return 0h instead the correct guest
instruction bytes .
Recommend Workaround:
To determine what instruction the guest was executing the hypervisor
will have to decode the instruction at the instruction pointer.
The recommended workaround can not be implemented for the SEV
guest because guest memory is encrypted with the guest specific key,
and instruction decoder will not be able to decode the instruction
bytes. If we hit this errata in the SEV guest then log the message
and request a guest shutdown.
Reported-by: Venkatesh Srinivas <venkateshs@google.com>
Cc: Jim Mattson <jmattson@google.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
for 32-bit guests
s390: interrupt cleanup, introduction of the Guest Information Block,
preparation for processor subfunctions in cpu models
PPC: bug fixes and improvements, especially related to machine checks
and protection keys
x86: many, many cleanups, including removing a bunch of MMU code for
unnecessary optimizations; plus AVIC fixes.
Generic: memcg accounting
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJci+7XAAoJEL/70l94x66DUMkIAKvEefhceySHYiTpfefjLjIC
16RewgHa+9CO4Oo5iXiWd90fKxtXLXmxDQOS4VGzN0rxvLGRw/fyXIxL1MDOkaAO
l8SLSNuewY4XBUgISL3PMz123r18DAGOuy9mEcYU/IMesYD2F+wy5lJ17HIGq6X2
RpoF1p3qO1jfkPTKOob6Ixd4H5beJNPKpdth7LY3PJaVhDxgouj32fxnLnATVSnN
gENQ10fnt8BCjshRYW6Z2/9bF15JCkUFR1xdBW2/xh1oj+kvPqqqk2bEN1eVQzUy
2hT/XkwtpthqjSbX8NNavWRSFnOnbMLTRKQyIXmFVsM5VoSrwtiGsCFzBgcT++I=
=XIzU
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"ARM:
- some cleanups
- direct physical timer assignment
- cache sanitization for 32-bit guests
s390:
- interrupt cleanup
- introduction of the Guest Information Block
- preparation for processor subfunctions in cpu models
PPC:
- bug fixes and improvements, especially related to machine checks
and protection keys
x86:
- many, many cleanups, including removing a bunch of MMU code for
unnecessary optimizations
- AVIC fixes
Generic:
- memcg accounting"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (147 commits)
kvm: vmx: fix formatting of a comment
KVM: doc: Document the life cycle of a VM and its resources
MAINTAINERS: Add KVM selftests to existing KVM entry
Revert "KVM/MMU: Flush tlb directly in the kvm_zap_gfn_range()"
KVM: PPC: Book3S: Add count cache flush parameters to kvmppc_get_cpu_char()
KVM: PPC: Fix compilation when KVM is not enabled
KVM: Minor cleanups for kvm_main.c
KVM: s390: add debug logging for cpu model subfunctions
KVM: s390: implement subfunction processor calls
arm64: KVM: Fix architecturally invalid reset value for FPEXC32_EL2
KVM: arm/arm64: Remove unused timer variable
KVM: PPC: Book3S: Improve KVM reference counting
KVM: PPC: Book3S HV: Fix build failure without IOMMU support
Revert "KVM: Eliminate extra function calls in kvm_get_dirty_log_protect()"
x86: kvmguest: use TSC clocksource if invariant TSC is exposed
KVM: Never start grow vCPU halt_poll_ns from value below halt_poll_ns_grow_start
KVM: Expose the initial start value in grow_halt_poll_ns() as a module parameter
KVM: grow_halt_poll_ns() should never shrink vCPU halt_poll_ns
KVM: x86/mmu: Consolidate kvm_mmu_zap_all() and kvm_mmu_zap_mmio_sptes()
KVM: x86/mmu: WARN if zapping a MMIO spte results in zapping children
...
Move L!TF to a separate directory so the MDS stuff can be added at the
side. Otherwise the all hardware vulnerabilites have their own top level
entry. Should have done that right away.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jon Masters <jcm@redhat.com>
CPUs which are affected by L1TF and MDS mitigate MDS with the L1D Flush on
VMENTER when updated microcode is installed.
If a CPU is not affected by L1TF or if the L1D Flush is not in use, then
MDS mitigation needs to be invoked explicitly.
For these cases, follow the host mitigation state and invoke the MDS
mitigation before VMENTER.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Jon Masters <jcm@redhat.com>
Tested-by: Jon Masters <jcm@redhat.com>
There are many KVM kernel memory allocations which are tied to the life of
the VM process and should be charged to the VM process's cgroup. If the
allocations aren't tied to the process, the OOM killer will not know
that killing the process will free the associated kernel memory.
Add __GFP_ACCOUNT flags to many of the allocations which are not yet being
charged to the VM process's cgroup.
Tested:
Ran all kvm-unit-tests on a 64 bit Haswell machine, the patch
introduced no new failures.
Ran a kernel memory accounting test which creates a VM to touch
memory and then checks that the kernel memory allocated for the
process is within certain bounds.
With this patch we account for much more of the vmalloc and slab memory
allocated for the VM.
Signed-off-by: Ben Gardon <bgardon@google.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The preemption timer can be started even if there is a vmentry
failure during or after loading guest state. That is pointless,
move the call after all conditions have been checked.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Previously, 'commit f99e3daf94 ("KVM: x86: Add Intel PT
virtualization work mode")' work mode' offered framework
to support Intel PT virtualization. However, the patch has
some typos in vmx_vmentry_ctrl() and vmx_vmexit_ctrl(), e.g.
used wrong flags and wrong variable, which will cause the
VM entry failure later.
Fixes: 'commit f99e3daf94 ("KVM: x86: Add Intel PT virtualization work mode")'
Signed-off-by: Yu Zhang <yu.c.zhang@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Ensure that the VCPU free path goes through vmx_leave_nested and
thus nested_vmx_vmexit, so that the cancellation of the timer does
not have to be in free_nested. In addition, because some paths through
nested_vmx_vmexit do not go through sync_vmcs12, the cancellation of
the timer is moved there.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some Posted-Interrupts from passthrough devices may be lost or
overwritten when the vCPU is in runnable state.
The SN (Suppress Notification) of PID (Posted Interrupt Descriptor) will
be set when the vCPU is preempted (vCPU in KVM_MP_STATE_RUNNABLE state
but not running on physical CPU). If a posted interrupt coming at this
time, the irq remmaping facility will set the bit of PIR (Posted
Interrupt Requests) without ON (Outstanding Notification).
So this interrupt can't be sync to APIC virtualization register and
will not be handled by Guest because ON is zero.
Signed-off-by: Luwei Kang <luwei.kang@intel.com>
[Eliminate the pi_clear_sn fast path. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VMX is only accessible in protected mode, remove a confusing check
that causes the conditional to lack a final "else" branch.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Regarding segments with a limit==0xffffffff, the SDM officially states:
When the effective limit is FFFFFFFFH (4 GBytes), these accesses may
or may not cause the indicated exceptions. Behavior is
implementation-specific and may vary from one execution to another.
In practice, all CPUs that support VMX ignore limit checks for "flat
segments", i.e. an expand-up data or code segment with base=0 and
limit=0xffffffff. This is subtly different than wrapping the effective
address calculation based on the address size, as the flat segment
behavior also applies to accesses that would wrap the 4g boundary, e.g.
a 4-byte access starting at 0xffffffff will access linear addresses
0xffffffff, 0x0, 0x1 and 0x2.
Fixes: f9eb4af67c ("KVM: nVMX: VMX instructions: add checks for #GP/#SS exceptions")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The address size of an instruction affects the effective address, not
the virtual/linear address. The final address may still be truncated,
e.g. to 32-bits outside of long mode, but that happens irrespective of
the address size, e.g. a 32-bit address size can yield a 64-bit virtual
address when using FS/GS with a non-zero base.
Fixes: 064aea7747 ("KVM: nVMX: Decoding memory operands of VMX instructions")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The VMCS.EXIT_QUALIFCATION field reports the displacements of memory
operands for various instructions, including VMX instructions, as a
naturally sized unsigned value, but masks the value by the addr size,
e.g. given a ModRM encoded as -0x28(%ebp), the -0x28 displacement is
reported as 0xffffffd8 for a 32-bit address size. Despite some weird
wording regarding sign extension, the SDM explicitly states that bits
beyond the instructions address size are undefined:
In all cases, bits of this field beyond the instruction’s address
size are undefined.
Failure to sign extend the displacement results in KVM incorrectly
treating a negative displacement as a large positive displacement when
the address size of the VMX instruction is smaller than KVM's native
size, e.g. a 32-bit address size on a 64-bit KVM.
The very original decoding, added by commit 064aea7747 ("KVM: nVMX:
Decoding memory operands of VMX instructions"), sort of modeled sign
extension by truncating the final virtual/linear address for a 32-bit
address size. I.e. it messed up the effective address but made it work
by adjusting the final address.
When segmentation checks were added, the truncation logic was kept
as-is and no sign extension logic was introduced. In other words, it
kept calculating the wrong effective address while mostly generating
the correct virtual/linear address. As the effective address is what's
used in the segment limit checks, this results in KVM incorreclty
injecting #GP/#SS faults due to non-existent segment violations when
a nested VMM uses negative displacements with an address size smaller
than KVM's native address size.
Using the -0x28(%ebp) example, an EBP value of 0x1000 will result in
KVM using 0x100000fd8 as the effective address when checking for a
segment limit violation. This causes a 100% failure rate when running
a 32-bit KVM build as L1 on top of a 64-bit KVM L0.
Fixes: f9eb4af67c ("KVM: nVMX: VMX instructions: add checks for #GP/#SS exceptions")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the clearing of the common registers (not 64-bit-only) to the start
of the flow that clears registers holding guest state. This is
purely a cosmetic change so that the label doesn't point at a blank line
and a #define.
No functional change intended.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
...now that the sub-routine follows standard calling conventions.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
...to make it callable from C code.
Note that because KVM chooses to be ultra paranoid about guest register
values, all callee-save registers are still cleared after VM-Exit even
though the host's values are now reloaded from the stack.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
...to prepare for making the assembly sub-routine callable from C code.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
...to prepare for making the sub-routine callable from C code.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
...to prepare for making the sub-routine callable from C code. That
means returning the result in RAX. Since RAX will be used to return the
result, use it as the scratch register as well to make the code readable
and to document that the scratch register is more or less arbitrary.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
...now that the name is no longer usurped by a defunct helper function.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
...now that the code is no longer tagged with STACK_FRAME_NON_STANDARD.
Arguably, providing __vmx_vcpu_run() to break up vmx_vcpu_run() is
valuable on its own, but the previous split was purposely made as small
as possible to limit the effects STACK_FRAME_NON_STANDARD. In other
words, the current split is now completely arbitrary and likely not the
most logical.
This also allows renaming ____vmx_vcpu_run() to __vmx_vcpu_run() in a
future patch.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As evidenced by the myriad patches leading up to this moment, using
an inline asm blob for vCPU-run is nothing short of horrific. It's also
been called "unholy", "an abomination" and likely a whole host of other
names that would violate the Code of Conduct if recorded here and now.
The code is relocated nearly verbatim, e.g. quotes, newlines, tabs and
__stringify need to be dropped, but other than those cosmetic changes
the only functional changees are to add the "call" and replace the final
"jmp" with a "ret".
Note that STACK_FRAME_NON_STANDARD is also dropped from __vmx_vcpu_run().
Suggested-by: Andi Kleen <ak@linux.intel.com>
Suggested-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
...in preparation for moving to a proper assembly sub-routnine.
vCPU-run isn't a leaf function since it calls vmx_update_host_rsp()
and vmx_vmenter(). And since we need to save/restore RBP anyways,
unconditionally creating the frame costs a single MOV, i.e. don't
bother keying off CONFIG_FRAME_POINTER or using FRAME_BEGIN, etc...
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
...to prepare for moving the inline asm to a proper asm sub-routine.
Eliminating the immediates allows a nearly verbatim move, e.g. quotes,
newlines, tabs and __stringify need to be dropped, but other than those
cosmetic changes the only function change will be to replace the final
"jmp" with a "ret".
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit ca83b4a7f2 ("x86/KVM/VMX: Add find_msr() helper function")
introduces the helper function find_msr(), which returns -ENOENT when
not find the msr in vmx->msr_autoload.guest/host. Correct checking contion
of no more available entry in vmx->msr_autoload.
Fixes: ca83b4a7f2 ("x86/KVM/VMX: Add find_msr() helper function")
Cc: stable@vger.kernel.org
Signed-off-by: Xiaoyao Li <xiaoyao.li@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some Posted-Interrupts from passthrough devices may be lost or
overwritten when the vCPU is in runnable state.
The SN (Suppress Notification) of PID (Posted Interrupt Descriptor) will
be set when the vCPU is preempted (vCPU in KVM_MP_STATE_RUNNABLE state but
not running on physical CPU). If a posted interrupt comes at this time,
the irq remapping facility will set the bit of PIR (Posted Interrupt
Requests) but not ON (Outstanding Notification). Then, the interrupt
will not be seen by KVM, which always expects PID.ON=1 if PID.PIR=1
as documented in the Intel processor SDM but not in the VT-d specification.
To fix this, restore the invariant after PID.SN is cleared.
Signed-off-by: Luwei Kang <luwei.kang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A recently added preemption timer consistency check was unintentionally
dropped when the consistency checks were being reorganized to match the
SDM's ordering.
Fixes: 461b4ba4c7 ("KVM: nVMX: Move the checks for VM-Execution Control Fields to a separate helper function")
Cc: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SDM says MSR_IA32_VMX_PROCBASED_CTLS2 is only available "If
(CPUID.01H:ECX.[5] && IA32_VMX_PROCBASED_CTLS[63])". It was found that
some old cpus (namely "Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz (family: 0x6,
model: 0xf, stepping: 0x6") don't have it. Add the missing check.
Reported-by: Zdenek Kaspar <zkaspar82@gmail.com>
Tested-by: Zdenek Kaspar <zkaspar82@gmail.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
...now that all other references to struct vcpu_vmx have been removed.
Note that 'vmx' still needs to be passed into the asm blob in _ASM_ARG1
as it is consumed by vmx_update_host_rsp(). And similar to that code,
use _ASM_ARG2 in the assembly code to prepare for moving to proper asm,
while explicitly referencing the exact registers in the clobber list for
clarity in the short term and to avoid additional precompiler games.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A failed VM-Enter (obviously) didn't succeed, meaning the CPU never
executed an instrunction in guest mode and so can't have changed the
general purpose registers.
In addition to saving some instructions in the VM-Fail case, this also
provides a separate path entirely and thus an opportunity to propagate
the fail condition to vmx->fail via register without introducing undue
pain. Using a register, as opposed to directly referencing vmx->fail,
eliminates the need to pass the offset of 'fail', which will simplify
moving the code to proper assembly in future patches.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Switching the ordering allows for an out-of-line path for VM-Fail
that elides saving guest state but still shares the register clearing
with the VM-Exit path.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
...and remove struct vcpu_vmx's temporary __launched variable.
Eliminating __launched is a bonus, the real motivation is to get to the
point where the only reference to struct vcpu_vmx in the asm code is
to vcpu.arch.regs, which will simplify moving the blob to a proper asm
file. Note that also means this approach is deliberately different than
what is used in nested_vmx_check_vmentry_hw().
Use BL as it is a callee-save register in both 32-bit and 64-bit ABIs,
i.e. it can't be modified by vmx_update_host_rsp(), to avoid having to
temporarily save/restore the launched flag.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Providing a helper function to update HOST_RSP is visibly easier to
read, and more importantly (for the future) eliminates two arguments to
the VM-Enter assembly blob. Reducing the number of arguments to the asm
blob is for all intents and purposes a prerequisite to moving the code
to a proper assembly routine. It's not truly mandatory, but it greatly
simplifies the future code, and the cost of the extra CALL+RET is
negligible in the grand scheme.
Note that although _ASM_ARG[1-3] can be used in the inline asm itself,
the intput/output constraints need to be manually defined. gcc will
actually compile with _ASM_ARG[1-3] specified as constraints, but what
it actually ends up doing with the bogus constraint is unknown.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
...to eliminate its parameter and struct vcpu_vmx offset definition
from the assembly blob. Accessing CR2 from C versus assembly doesn't
change the likelihood of taking a page fault (and modifying CR2) while
it's loaded with the guest's value, so long as we don't do anything
silly between accessing CR2 and VM-Enter/VM-Exit.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, host_rsp is cached on a per-vCPU basis, i.e. it's stored in
struct vcpu_vmx. In non-nested usage the caching is for all intents
and purposes 100% effective, e.g. only the first VMLAUNCH needs to
synchronize VMCS.HOST_RSP since the call stack to vmx_vcpu_run() is
identical each and every time. But when running a nested guest, KVM
must invalidate the cache when switching the current VMCS as it can't
guarantee the new VMCS has the same HOST_RSP as the previous VMCS. In
other words, the cache loses almost all of its efficacy when running a
nested VM.
Move host_rsp to struct vmcs_host_state, which is per-VMCS, so that it
is cached on a per-VMCS basis and restores its 100% hit rate when
nested VMs are in play.
Note that the host_rsp cache for vmcs02 essentially "breaks" when
nested early checks are enabled as nested_vmx_check_vmentry_hw() will
see a different RSP at the time of its VM-Enter. While it's possible
to avoid even that VMCS.HOST_RSP synchronization, e.g. by employing a
dedicated VM-Exit stack, there is little motivation for doing so as
the overhead of two VMWRITEs (~55 cycles) is dwarfed by the overhead
of the extra VMX transition (600+ cycles) and is a proverbial drop in
the ocean relative to the total cost of a nested transtion (10s of
thousands of cycles).
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
...and provide an explicit name for the constraint. Naming the input
constraint makes the code self-documenting and also avoids the fragility
of numerically referring to constraints, e.g. %4 breaks badly whenever
the constraints are modified.
Explicitly using RDX was inherited from vCPU-run, i.e. completely
arbitrary. Even vCPU-run doesn't truly need to explicitly use RDX, but
doing so is more robust as vCPU-run needs tight control over its
register usage.
Note that while the naming "conflict" between host_rsp and HOST_RSP
is slightly confusing, the former will be renamed slightly in a
future patch, at which point HOST_RSP is absolutely what is desired.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Temporarily propagating vmx->loaded_vmcs->launched to vmx->__launched
is not functionally necessary, but rather was done historically to
avoid passing both 'vmx' and 'loaded_vmcs' to the vCPU-run asm blob.
Nested early checks inherited this behavior by virtue of copy+paste.
A future patch will move HOST_RSP caching to be per-VMCS, i.e. store
'host_rsp' in loaded VMCS. Now that the reference to 'vmx->fail' is
also gone from nested early checks, referencing 'loaded_vmcs' directly
means we can drop the 'vmx' reference when introducing per-VMCS RSP
caching. And it means __launched can be dropped from struct vcpu_vmx
if/when vCPU-run receives similar treatment.
Note the use of a named register constraint for 'loaded_vmcs'. Using
RCX to hold 'vmx' was inherited from vCPU-run. In the vCPU-run case,
the scratch register needs to be explicitly defined as it is crushed
when loading guest state, i.e. deferring to the compiler would corrupt
the pointer. Since nested early checks never loads guests state, it's
a-ok to let the compiler pick any register. Naming the constraint
avoids the fragility of referencing constraints via %1, %2, etc.., which
breaks horribly when modifying constraints, and generally makes the asm
blob more readable.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
...to take advantage of __GCC_ASM_FLAG_OUTPUTS__ when possible.
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Unlike the primary vCPU-run flow, the nested early checks code doesn't
actually want to propagate VM-Fail back to 'vmx'. Yay copy+paste.
In additional to eliminating the need to clear vmx->fail before
returning, using a local boolean also drops a reference to 'vmx' in the
asm blob. Dropping the reference to 'vmx' will save a register in the
long run as future patches will shift all pointer references from 'vmx'
to 'vmx->loaded_vmcs'.
Fixes: 52017608da ("KVM: nVMX: add option to perform early consistency checks via H/W")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Using %1 to reference RCX, i.e. the 'vmx' pointer', is obtuse and
fragile, e.g. it results in cryptic and infurating compile errors if the
output constraints are touched by anything more than a gentle breeze.
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
...as it doesn't technically actually do anything non-standard with the
stack even though it modifies RSP in a weird way. E.g. RSP is loaded
with VMCS.HOST_RSP if the VM-Enter gets far enough to trigger VM-Exit,
but it's simply reloaded with the current value.
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
RAX is not touched by nested_vmx_check_vmentry_hw(), directly or
indirectly (e.g. vmx_vmenter()). Remove it from the clobber list.
Fixes: 52017608da ("KVM: nVMX: add option to perform early consistency checks via H/W")
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Per commit c20363006a ("KVM: VMX: Let gcc to choose which registers
to save (x86_64)"), the only reason RDX is saved/loaded to/from the
stack is because it was specified as an input, i.e. couldn't be marked
as clobbered (ignoring the fact that "saving" it to a dummy output
would indirectly mark it as clobbered).
Now that RDX is no longer an input, clobber it.
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Load RDX with the VMCS.HOST_RSP field encoding on-demand instead of
delegating to the compiler via an input constraint. In addition to
saving one whole MOV instruction, this allows RDX to be properly
clobbered (in a future patch) instead of being saved/loaded to/from
the stack.
Despite nested_vmx_check_vmentry_hw() having similar code, leave it
alone, for now. In that case, RDX is unconditionally used and isn't
clobbered, i.e. sending in HOST_RSP as an input is simpler.
Note that because HOST_RSP is an enum and not a define, it must be
redefined as an immediate instead of using __stringify(HOST_RSP). The
naming "conflict" between host_rsp and HOST_RSP is slightly confusing,
but the former will be removed in a future patch, at which point
HOST_RSP is absolutely what is desired.
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
RSI is clobbered by the vCPU-run asm blob, but it's not marked as such,
probably because GCC doesn't let you mark inputs as clobbered. "Save"
RSI to a dummy output so that GCC recognizes it as being clobbered.
Fixes: 773e8a0425 ("x86/kvm: use Enlightened VMCS when running on Hyper-V")
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In the vCPU-run asm blob, the guest's RCX is temporarily saved onto the
stack after VM-Exit as the exit flow must first load a register with a
pointer to the vCPU's save area in order to save the guest's registers.
RCX is arbitrarily designated as the scratch register.
Since the stack usage is to (1)save host, (2)save guest, (3)load host
and (4)load guest, the code can't conform to the stack's natural FIFO
semantics, i.e. it can't simply do PUSH/POP. Regardless of whether it
is done for the host's value or guest's value, at some point the code
needs to access the stack using a non-traditional method, e.g. MOV
instead of POP. vCPU-run opts to create a placeholder on the stack for
guest's RCX (by adjusting RSP) and saves RCX to its place immediately
after VM-Exit (via MOV).
In other words, the purpose of the first 'PUSH RCX' at the start of
the vCPU-run asm blob is to adjust RSP down, i.e. there's no need to
actually access memory. Use 'SUB $wordsize, RSP' instead of 'PUSH RCX'
to make it more obvious that the intent is simply to create a gap on
the stack for the guest's RCX.
Reviewed-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
...except RSP, which is restored by hardware as part of VM-Exit.
Paolo theorized that restoring registers from the stack after a VM-Exit
in lieu of zeroing them could lead to speculative execution with the
guest's values, e.g. if the stack accesses miss the L1 cache[1].
Zeroing XORs are dirt cheap, so just be ultra-paranoid.
Note that the scratch register (currently RCX) used to save/restore the
guest state is also zeroed as its host-defined value is loaded via the
stack, just with a MOV instead of a POP.
[1] https://patchwork.kernel.org/patch/10771539/#22441255
Fixes: 0cb5b30698 ("kvm: vmx: Scrub hardware GPRs at VM-exit")
Cc: <stable@vger.kernel.org>
Cc: Jim Mattson <jmattson@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Nested early checks does a manual comparison of a VMCS' launched status
in its asm blob to execute the correct VM-Enter instruction, i.e.
VMLAUNCH vs. VMRESUME. The launched flag is a bool, which is a typedef
of _Bool. C99 does not define an exact size for _Bool, stating only
that is must be large enough to hold '0' and '1'. Most, if not all,
compilers use a single byte for _Bool, including gcc[1].
The use of 'cmpl' instead of 'cmpb' was not deliberate, but rather the
result of a copy-paste as the asm blob was directly derived from the asm
blob for vCPU-run.
This has not caused any known problems, likely due to compilers aligning
variables to 4-byte or 8-byte boundaries and KVM zeroing out struct
vcpu_vmx during allocation. I.e. vCPU-run accesses "junk" data, it just
happens to always be zero and so doesn't affect the result.
[1] https://gcc.gnu.org/ml/gcc-patches/2000-10/msg01127.html
Fixes: 52017608da ("KVM: nVMX: add option to perform early consistency checks via H/W")
Cc: <stable@vger.kernel.org>
Reviewed-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The vCPU-run asm blob does a manual comparison of a VMCS' launched
status to execute the correct VM-Enter instruction, i.e. VMLAUNCH vs.
VMRESUME. The launched flag is a bool, which is a typedef of _Bool.
C99 does not define an exact size for _Bool, stating only that is must
be large enough to hold '0' and '1'. Most, if not all, compilers use
a single byte for _Bool, including gcc[1].
Originally, 'launched' was of type 'int' and so the asm blob used 'cmpl'
to check the launch status. When 'launched' was moved to be stored on a
per-VMCS basis, struct vcpu_vmx's "temporary" __launched flag was added
in order to avoid having to pass the current VMCS into the asm blob.
The new '__launched' was defined as a 'bool' and not an 'int', but the
'cmp' instruction was not updated.
This has not caused any known problems, likely due to compilers aligning
variables to 4-byte or 8-byte boundaries and KVM zeroing out struct
vcpu_vmx during allocation. I.e. vCPU-run accesses "junk" data, it just
happens to always be zero and so doesn't affect the result.
[1] https://gcc.gnu.org/ml/gcc-patches/2000-10/msg01127.html
Fixes: d462b81923 ("KVM: VMX: Keep list of loaded VMCSs, instead of vcpus")
Cc: <stable@vger.kernel.org>
Reviewed-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Bugzilla: 1671904
There are multiple code paths where an hrtimer may have been started to
emulate an L1 VMX preemption timer that can result in a call to free_nested
without an intervening L2 exit where the hrtimer is normally
cancelled. Unconditionally cancel in free_nested to cover all cases.
Embargoed until Feb 7th 2019.
Signed-off-by: Peter Shier <pshier@google.com>
Reported-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Reported-by: Felix Wilhelm <fwilhelm@google.com>
Cc: stable@kernel.org
Message-Id: <20181011184646.154065-1-pshier@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
With the following commit:
73d5e2b472 ("cpu/hotplug: detect SMT disabled by BIOS")
... the hotplug code attempted to detect when SMT was disabled by BIOS,
in which case it reported SMT as permanently disabled. However, that
code broke a virt hotplug scenario, where the guest is booted with only
primary CPU threads, and a sibling is brought online later.
The problem is that there doesn't seem to be a way to reliably
distinguish between the HW "SMT disabled by BIOS" case and the virt
"sibling not yet brought online" case. So the above-mentioned commit
was a bit misguided, as it permanently disabled SMT for both cases,
preventing future virt sibling hotplugs.
Going back and reviewing the original problems which were attempted to
be solved by that commit, when SMT was disabled in BIOS:
1) /sys/devices/system/cpu/smt/control showed "on" instead of
"notsupported"; and
2) vmx_vm_init() was incorrectly showing the L1TF_MSG_SMT warning.
I'd propose that we instead consider #1 above to not actually be a
problem. Because, at least in the virt case, it's possible that SMT
wasn't disabled by BIOS and a sibling thread could be brought online
later. So it makes sense to just always default the smt control to "on"
to allow for that possibility (assuming cpuid indicates that the CPU
supports SMT).
The real problem is #2, which has a simple fix: change vmx_vm_init() to
query the actual current SMT state -- i.e., whether any siblings are
currently online -- instead of looking at the SMT "control" sysfs value.
So fix it by:
a) reverting the original "fix" and its followup fix:
73d5e2b472 ("cpu/hotplug: detect SMT disabled by BIOS")
bc2d8d262c ("cpu/hotplug: Fix SMT supported evaluation")
and
b) changing vmx_vm_init() to query the actual current SMT state --
instead of the sysfs control value -- to determine whether the L1TF
warning is needed. This also requires the 'sched_smt_present'
variable to exported, instead of 'cpu_smt_control'.
Fixes: 73d5e2b472 ("cpu/hotplug: detect SMT disabled by BIOS")
Reported-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Joe Mario <jmario@redhat.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: kvm@vger.kernel.org
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/e3a85d585da28cc333ecbc1e78ee9216e6da9396.1548794349.git.jpoimboe@redhat.com
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
arch/x86/kvm/lapic.c:1037:27: warning: this statement may fall through [-Wimplicit-fallthrough=]
arch/x86/kvm/lapic.c:1876:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
arch/x86/kvm/hyperv.c:1637:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
arch/x86/kvm/svm.c:4396:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
arch/x86/kvm/mmu.c:4372:36: warning: this statement may fall through [-Wimplicit-fallthrough=]
arch/x86/kvm/x86.c:3835:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
arch/x86/kvm/x86.c:7938:23: warning: this statement may fall through [-Wimplicit-fallthrough=]
arch/x86/kvm/vmx/vmx.c:2015:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
arch/x86/kvm/vmx/vmx.c:1773:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enabling -Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit e2e871ab2f ("x86/kvm/hyper-v: Introduce nested_get_evmcs_version()
helper") broke EVMCS enablement: to set vmcs_version we now call
nested_get_evmcs_version() but this function checks
enlightened_vmcs_enabled flag which is not yet set so we end up returning
zero.
Fix the issue by re-arranging things in nested_enable_evmcs().
Fixes: e2e871ab2f ("x86/kvm/hyper-v: Introduce nested_get_evmcs_version() helper")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
...along with the function's STACK_FRAME_NON_STANDARD tag. Moving the
asm blob results in a significantly smaller amount of code that is
marked with STACK_FRAME_NON_STANDARD, which makes it far less likely
that gcc will split the function and trigger a spurious objtool warning.
As a bonus, removing STACK_FRAME_NON_STANDARD from vmx_vcpu_run() allows
the bulk of code to be properly checked by objtool.
Because %rbp is not loaded via VMCS fields, vmx_vcpu_run() must manually
save/restore the host's RBP and load the guest's RBP prior to calling
vmx_vmenter(). Modifying %rbp triggers objtool's stack validation code,
and so vmx_vcpu_run() is tagged with STACK_FRAME_NON_STANDARD since it's
impossible to avoid modifying %rbp.
Unfortunately, vmx_vcpu_run() is also a gigantic function that gcc will
split into separate functions, e.g. so that pieces of the function can
be inlined. Splitting the function means that the compiled Elf file
will contain one or more vmx_vcpu_run.part.* functions in addition to
a vmx_vcpu_run function. Depending on where the function is split,
objtool may warn about a "call without frame pointer save/setup" in
vmx_vcpu_run.part.* since objtool's stack validation looks for exact
names when whitelisting functions tagged with STACK_FRAME_NON_STANDARD.
Up until recently, the undesirable function splitting was effectively
blocked because vmx_vcpu_run() was tagged with __noclone. At the time,
__noclone had an unintended side effect that put vmx_vcpu_run() into a
separate optimization unit, which in turn prevented gcc from inlining
the function (or any of its own function calls) and thus eliminated gcc's
motivation to split the function. Removing the __noclone attribute
allowed gcc to optimize vmx_vcpu_run(), exposing the objtool warning.
Kudos to Qian Cai for root causing that the fnsplit optimization is what
caused objtool to complain.
Fixes: 453eafbe65 ("KVM: VMX: Move VM-Enter + VM-Exit handling to non-inline sub-routines")
Tested-by: Qian Cai <cai@lca.pw>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We get some warnings when building kernel with W=1:
arch/x86/kvm/vmx/vmx.c:426:5: warning: no previous prototype for ‘kvm_fill_hv_flush_list_func’ [-Wmissing-prototypes]
arch/x86/kvm/vmx/nested.c:58:6: warning: no previous prototype for ‘init_vmcs_shadow_fields’ [-Wmissing-prototypes]
Make them static to fix this.
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This changes the allocation of cached_vmcs12 to use kzalloc instead of
kmalloc. This removes the information leak found by Syzkaller (see
Reported-by) in this case and prevents similar leaks from happening
based on cached_vmcs12.
It also changes vmx_get_nested_state to copy out the full 4k VMCS12_SIZE
in copy_to_user rather than only the size of the struct.
Tested: rebuilt against head, booted, and ran the syszkaller repro
https://syzkaller.appspot.com/text?tag=ReproC&x=174efca3400000 without
observing any problems.
Reported-by: syzbot+ded1696f6b50b615b630@syzkaller.appspotmail.com
Fixes: 8fcc4b5923
Cc: stable@vger.kernel.org
Signed-off-by: Tom Roeder <tmroeder@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fix a recently introduced bug that results in the wrong VMCS control
field being updated when applying a IA32_PERF_GLOBAL_CTRL errata.
Fixes: c73da3fcab ("KVM: VMX: Properly handle dynamic VM Entry/Exit controls")
Reported-by: Harald Arnesen <harald@skogtun.org>
Tested-by: Harald Arnesen <harald@skogtun.org>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since commit 09abb5e3e5 ("KVM: nVMX: call kvm_skip_emulated_instruction
in nested_vmx_{fail,succeed}") nested_vmx_failValid() results in
kvm_skip_emulated_instruction() so doing it again in handle_vmptrld() when
vmptr address is not backed is wrong, we end up advancing RIP twice.
Fixes: fca91f6d60 ("kvm: nVMX: Set VM instruction error for VMPTRLD of unbacked page")
Reported-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
The "ret" is initialized to be ENOTSUPP. The return value of
__hv_remote_flush_tlb_with_range() will be Or with "ret" when ept
table potiners are mismatched. This will cause return ENOTSUPP even if
flush tlb successfully. This patch is to fix the issue and set
"ret" to 0.
Fixes: a5c214dad1 ("KVM/VMX: Change hv flush logic when ept tables are mismatched.")
Signed-off-by: Lan Tianyu <Tianyu.Lan@microsoft.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
ctl_bitmask in pt_desc is of type u64. When an integer like 0xf is
being left shifted more than 32 bits, the behavior is undefined.
Fix this by adding suffix ULL to integer 0xf.
Addresses-Coverity-ID: 1476095 ("Bad bit shift operation")
Fixes: 6c0f0bba85 ("KVM: x86: Introduce a function to initialize the PT configuration")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Luwei Kang <luwei.kang@intel.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
single-stepping fixes, improved tracing, various timer and vGIC
fixes
* x86: Processor Tracing virtualization, STIBP support, some correctness fixes,
refactorings and splitting of vmx.c, use the Hyper-V range TLB flush hypercall,
reduce order of vcpu struct, WBNOINVD support, do not use -ftrace for __noclone
functions, nested guest support for PAUSE filtering on AMD, more Hyper-V
enlightenments (direct mode for synthetic timers)
* PPC: nested VFIO
* s390: bugfixes only this time
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJcH0vFAAoJEL/70l94x66Dw/wH/2FZp1YOM5OgiJzgqnXyDbyf
dNEfWo472MtNiLsuf+ZAfJojVIu9cv7wtBfXNzW+75XZDfh/J88geHWNSiZDm3Fe
aM4MOnGG0yF3hQrRQyEHe4IFhGFNERax8Ccv+OL44md9CjYrIrsGkRD08qwb+gNh
P8T/3wJEKwUcVHA/1VHEIM8MlirxNENc78p6JKd/C7zb0emjGavdIpWFUMr3SNfs
CemabhJUuwOYtwjRInyx1y34FzYwW3Ejuc9a9UoZ+COahUfkuxHE8u+EQS7vLVF6
2VGVu5SA0PqgmLlGhHthxLqVgQYo+dB22cRnsLtXlUChtVAq8q9uu5sKzvqEzuE=
=b4Jx
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"ARM:
- selftests improvements
- large PUD support for HugeTLB
- single-stepping fixes
- improved tracing
- various timer and vGIC fixes
x86:
- Processor Tracing virtualization
- STIBP support
- some correctness fixes
- refactorings and splitting of vmx.c
- use the Hyper-V range TLB flush hypercall
- reduce order of vcpu struct
- WBNOINVD support
- do not use -ftrace for __noclone functions
- nested guest support for PAUSE filtering on AMD
- more Hyper-V enlightenments (direct mode for synthetic timers)
PPC:
- nested VFIO
s390:
- bugfixes only this time"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (171 commits)
KVM: x86: Add CPUID support for new instruction WBNOINVD
kvm: selftests: ucall: fix exit mmio address guessing
Revert "compiler-gcc: disable -ftracer for __noclone functions"
KVM: VMX: Move VM-Enter + VM-Exit handling to non-inline sub-routines
KVM: VMX: Explicitly reference RCX as the vmx_vcpu pointer in asm blobs
KVM: x86: Use jmp to invoke kvm_spurious_fault() from .fixup
MAINTAINERS: Add arch/x86/kvm sub-directories to existing KVM/x86 entry
KVM/x86: Use SVM assembly instruction mnemonics instead of .byte streams
KVM/MMU: Flush tlb directly in the kvm_zap_gfn_range()
KVM/MMU: Flush tlb directly in kvm_set_pte_rmapp()
KVM/MMU: Move tlb flush in kvm_set_pte_rmapp() to kvm_mmu_notifier_change_pte()
KVM: Make kvm_set_spte_hva() return int
KVM: Replace old tlb flush function with new one to flush a specified range.
KVM/MMU: Add tlb flush with range helper function
KVM/VMX: Add hv tlb range flush support
x86/hyper-v: Add HvFlushGuestAddressList hypercall support
KVM: Add tlb_remote_flush_with_range callback in kvm_x86_ops
KVM: x86: Disable Intel PT when VMXON in L1 guest
KVM: x86: Set intercept for Intel PT MSRs read/write
KVM: x86: Implement Intel PT MSRs read/write emulation
...
Transitioning to/from a VMX guest requires KVM to manually save/load
the bulk of CPU state that the guest is allowed to direclty access,
e.g. XSAVE state, CR2, GPRs, etc... For obvious reasons, loading the
guest's GPR snapshot prior to VM-Enter and saving the snapshot after
VM-Exit is done via handcoded assembly. The assembly blob is written
as inline asm so that it can easily access KVM-defined structs that
are used to hold guest state, e.g. moving the blob to a standalone
assembly file would require generating defines for struct offsets.
The other relevant aspect of VMX transitions in KVM is the handling of
VM-Exits. KVM doesn't employ a separate VM-Exit handler per se, but
rather treats the VMX transition as a mega instruction (with many side
effects), i.e. sets the VMCS.HOST_RIP to a label immediately following
VMLAUNCH/VMRESUME. The label is then exposed to C code via a global
variable definition in the inline assembly.
Because of the global variable, KVM takes steps to (attempt to) ensure
only a single instance of the owning C function, e.g. vmx_vcpu_run, is
generated by the compiler. The earliest approach placed the inline
assembly in a separate noinline function[1]. Later, the assembly was
folded back into vmx_vcpu_run() and tagged with __noclone[2][3], which
is still used today.
After moving to __noclone, an edge case was encountered where GCC's
-ftracer optimization resulted in the inline assembly blob being
duplicated. This was "fixed" by explicitly disabling -ftracer in the
__noclone definition[4].
Recently, it was found that disabling -ftracer causes build warnings
for unsuspecting users of __noclone[5], and more importantly for KVM,
prevents the compiler for properly optimizing vmx_vcpu_run()[6]. And
perhaps most importantly of all, it was pointed out that there is no
way to prevent duplication of a function with 100% reliability[7],
i.e. more edge cases may be encountered in the future.
So to summarize, the only way to prevent the compiler from duplicating
the global variable definition is to move the variable out of inline
assembly, which has been suggested several times over[1][7][8].
Resolve the aforementioned issues by moving the VMLAUNCH+VRESUME and
VM-Exit "handler" to standalone assembly sub-routines. Moving only
the core VMX transition codes allows the struct indexing to remain as
inline assembly and also allows the sub-routines to be used by
nested_vmx_check_vmentry_hw(). Reusing the sub-routines has a happy
side-effect of eliminating two VMWRITEs in the nested_early_check path
as there is no longer a need to dynamically change VMCS.HOST_RIP.
Note that callers to vmx_vmenter() must account for the CALL modifying
RSP, e.g. must subtract op-size from RSP when synchronizing RSP with
VMCS.HOST_RSP and "restore" RSP prior to the CALL. There are no great
alternatives to fudging RSP. Saving RSP in vmx_enter() is difficult
because doing so requires a second register (VMWRITE does not provide
an immediate encoding for the VMCS field and KVM supports Hyper-V's
memory-based eVMCS ABI). The other more drastic alternative would be
to use eschew VMCS.HOST_RSP and manually save/load RSP using a per-cpu
variable (which can be encoded as e.g. gs:[imm]). But because a valid
stack is needed at the time of VM-Exit (NMIs aren't blocked and a user
could theoretically insert INT3/INT1ICEBRK at the VM-Exit handler), a
dedicated per-cpu VM-Exit stack would be required. A dedicated stack
isn't difficult to implement, but it would require at least one page
per CPU and knowledge of the stack in the dumpstack routines. And in
most cases there is essentially zero overhead in dynamically updating
VMCS.HOST_RSP, e.g. the VMWRITE can be avoided for all but the first
VMLAUNCH unless nested_early_check=1, which is not a fast path. In
other words, avoiding the VMCS.HOST_RSP by using a dedicated stack
would only make the code marginally less ugly while requiring at least
one page per CPU and forcing the kernel to be aware (and approve) of
the VM-Exit stack shenanigans.
[1] cea15c24ca39 ("KVM: Move KVM context switch into own function")
[2] a3b5ba49a8 ("KVM: VMX: add the __noclone attribute to vmx_vcpu_run")
[3] 104f226bfd ("KVM: VMX: Fold __vmx_vcpu_run() into vmx_vcpu_run()")
[4] 95272c2937 ("compiler-gcc: disable -ftracer for __noclone functions")
[5] https://lkml.kernel.org/r/20181218140105.ajuiglkpvstt3qxs@treble
[6] https://patchwork.kernel.org/patch/8707981/#21817015
[7] https://lkml.kernel.org/r/ri6y38lo23g.fsf@suse.cz
[8] https://lkml.kernel.org/r/20181218212042.GE25620@tassilo.jf.intel.com
Suggested-by: Andi Kleen <ak@linux.intel.com>
Suggested-by: Martin Jambor <mjambor@suse.cz>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Nadav Amit <namit@vmware.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Martin Jambor <mjambor@suse.cz>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use '%% " _ASM_CX"' instead of '%0' to dereference RCX, i.e. the
'struct vcpu_vmx' pointer, in the VM-Enter asm blobs of vmx_vcpu_run()
and nested_vmx_check_vmentry_hw(). Using the symbolic name means that
adding/removing an output parameter(s) requires "rewriting" almost all
of the asm blob, which makes it nearly impossible to understand what's
being changed in even the most minor patches.
Opportunistically improve the code comments.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch is to register tlb_remote_flush_with_range callback with
hv tlb range flush interface.
Signed-off-by: Lan Tianyu <Tianyu.Lan@microsoft.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, Intel Processor Trace do not support tracing in L1 guest
VMX operation(IA32_VMX_MISC[bit 14] is 0). As mentioned in SDM,
on these type of processors, execution of the VMXON instruction will
clears IA32_RTIT_CTL.TraceEn and any attempt to write IA32_RTIT_CTL
causes a general-protection exception (#GP).
Signed-off-by: Luwei Kang <luwei.kang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
To save performance overhead, disable intercept Intel PT MSRs
read/write when Intel PT is enabled in guest.
MSR_IA32_RTIT_CTL is an exception that will always be intercepted.
Signed-off-by: Chao Peng <chao.p.peng@linux.intel.com>
Signed-off-by: Luwei Kang <luwei.kang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch implement Intel Processor Trace MSRs read/write
emulation.
Intel PT MSRs read/write need to be emulated when Intel PT
MSRs is intercepted in guest and during live migration.
Signed-off-by: Chao Peng <chao.p.peng@linux.intel.com>
Signed-off-by: Luwei Kang <luwei.kang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Initialize the Intel PT configuration when cpuid update.
Include cpuid inforamtion, rtit_ctl bit mask and the number of
address ranges.
Signed-off-by: Luwei Kang <luwei.kang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Load/Store Intel Processor Trace register in context switch.
MSR IA32_RTIT_CTL is loaded/stored automatically from VMCS.
In Host-Guest mode, we need load/resore PT MSRs only when PT
is enabled in guest.
Signed-off-by: Chao Peng <chao.p.peng@linux.intel.com>
Signed-off-by: Luwei Kang <luwei.kang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Expose Intel Processor Trace to guest only when
the PT works in Host-Guest mode.
Signed-off-by: Chao Peng <chao.p.peng@linux.intel.com>
Signed-off-by: Luwei Kang <luwei.kang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Intel Processor Trace virtualization can be work in one
of 2 possible modes:
a. System-Wide mode (default):
When the host configures Intel PT to collect trace packets
of the entire system, it can leave the relevant VMX controls
clear to allow VMX-specific packets to provide information
across VMX transitions.
KVM guest will not aware this feature in this mode and both
host and KVM guest trace will output to host buffer.
b. Host-Guest mode:
Host can configure trace-packet generation while in
VMX non-root operation for guests and root operation
for native executing normally.
Intel PT will be exposed to KVM guest in this mode, and
the trace output to respective buffer of host and guest.
In this mode, tht status of PT will be saved and disabled
before VM-entry and restored after VM-exit if trace
a virtual machine.
Signed-off-by: Chao Peng <chao.p.peng@linux.intel.com>
Signed-off-by: Luwei Kang <luwei.kang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Let the guest read the IA32_TSC MSR with the generic RDMSR instruction
as well as the specific RDTSC(P) instructions. Note that the hardware
applies the TSC multiplier and offset (when applicable) to the result of
RDMSR(IA32_TSC), just as it does to the result of RDTSC(P).
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Peter Shier <pshier@google.com>
Reviewed-by: Marc Orr <marcorr@google.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
According to the SDM, "NMI-window exiting" VM-exits wake a logical
processor from the same inactive states as would an NMI and
"interrupt-window exiting" VM-exits wake a logical processor from the
same inactive states as would an external interrupt. Specifically, they
wake a logical processor from the shutdown state and from the states
entered using the HLT and MWAIT instructions.
Fixes: 6dfacadd58 ("KVM: nVMX: Add support for activity state HLT")
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Peter Shier <pshier@google.com>
Suggested-by: Sean Christopherson <sean.j.christopherson@intel.com>
[Squashed comments of two Jim's patches and used the simplified code
hunk provided by Sean. - Radim]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Previously, the guest_fpu field was embedded in the kvm_vcpu_arch
struct. Unfortunately, the field is quite large, (e.g., 4352 bytes on my
current setup). This bloats the kvm_vcpu_arch struct for x86 into an
order 3 memory allocation, which can become a problem on overcommitted
machines. Thus, this patch moves the fpu state outside of the
kvm_vcpu_arch struct.
With this patch applied, the kvm_vcpu_arch struct is reduced to 15168
bytes for vmx on my setup when building the kernel with kvmconfig.
Suggested-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Marc Orr <marcorr@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
.. to improve readability and maintainability, and to align the code as per
the layout of the checks in chapter "VM Entries" in Intel SDM vol 3C.
Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Reviewed-by: Mihai Carabas <mihai.carabas@oracle.com>
Reviewed-by: Mark Kanda <mark.kanda@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
.. to improve readability and maintainability, and to align the code as per
the layout of the checks in chapter "VM Entries" in Intel SDM vol 3C.
Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Reviewed-by: Mihai Carabas <mihai.carabas@oracle.com>
Reviewed-by: Mark Kanda <mark.kanda@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
.. to improve readability and maintainability, and to align the code as per
the layout of the checks in chapter "VM Entries" in Intel SDM vol 3C.
Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Reviewed-by: Mihai Carabas <mihai.carabas@oracle.com>
Reviewed-by: Mark Kanda <mark.kanda@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
.. to improve readability and maintainability, and to align the code as per
the layout of the checks in chapter "VM Entries" in Intel SDM vol 3C.
Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Reviewed-by: Mihai Carabas <mihai.carabas@oracle.com>
Reviewed-by: Mark Kanda <mark.kanda@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Passing the enum and doing an indirect lookup is silly when we can
simply pass the field directly. Remove the "fast path" code in
nested_vmx_check_msr_switch_controls() as it's now nothing more than a
redundant check.
Remove the debug message rather than continue passing the enum for the
address field. Having debug messages for the MSRs themselves is useful
as MSR legality is a huge space, whereas messing up a physical address
means the VMM is fundamentally broken.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
.. to improve readability and maintainability, and to align the code as per
the layout of the checks in chapter "VM Entries" in Intel SDM vol 3C.
Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Reviewed-by: Mihai Carabas <mihai.carabas@oracle.com>
Reviewed-by: Mark Kanda <mark.kanda@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
.. as they are used only in nested vmx context.
Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Reviewed-by: Mihai Carabas <mihai.carabas@oracle.com>
Reviewed-by: Mark Kanda <mark.kanda@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch is to initialize ept_pointer to INVALID_PAGE and check it
before flushing ept tlb. If ept_pointer is invalid, bypass the flush
request.
Signed-off-by: Lan Tianyu <Tianyu.Lan@microsoft.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
According to section "VM-entry Failures During or After Loading Guest State"
in Intel SDM vol 3C,
"No MSRs are saved into the VM-exit MSR-store area."
when bit 31 of the exit reason is set.
Reported-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Suggested-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds Intel "Xeon CPU E3-1220 V2", with CPUID.01H.EAX=0x000306A8,
into the list of known broken CPUs which fail to support VMX preemption
timer. This bug was found while running the APIC timer test of
kvm-unit-test on this specific CPU, even though the errata info can't be
located in the public domain for this CPU.
Signed-off-by: Wei Huang <wei@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The upcoming KVM_GET_SUPPORTED_HV_CPUID ioctl will need to return
Enlightened VMCS version in HYPERV_CPUID_NESTED_FEATURES.EAX when
it was enabled.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Like IA32_STAR, IA32_LSTAR and IA32_FMASK only need to contain guest
values on VM-entry when the guest is in long mode and EFER.SCE is set.
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Peter Shier <pshier@google.com>
Reviewed-by: Marc Orr <marcorr@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SYSCALL raises #UD in compatibility mode on Intel CPUs, so it's
pointless to load the guest's IA32_CSTAR value into the hardware MSR.
IA32_CSTAR still provides 48 bits of storage on Intel CPUs that have
CPUID.80000001:EDX.LM[bit 29] set, so we cannot remove it from the
vmx_msr_index[] array.
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Peter Shier <pshier@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a comment explaining why MSR_STAR must be included in
vmx_msr_index[] even for i386 builds.
The elided comment has not been relevant since move_msr_up() was
introduced in commit a75beee6e4 ("KVM: VMX: Avoid saving and
restoring msrs on lightweight vmexit").
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Peter Shier <pshier@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
RDTSCP is supported in legacy mode as well as long mode. The
IA32_TSC_AUX MSR should be set to the correct guest value before
entering any guest that supports RDTSCP.
Fixes: 4e47c7a6d7 ("KVM: VMX: Add instruction rdtscp support for guest")
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Peter Shier <pshier@google.com>
Reviewed-by: Marc Orr <marcorr@google.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
From a functional perspective, this is (supposed to be) a straight
copy-paste of code. Code was moved piecemeal to nested.c as not all
code that could/should be moved was obviously nested-only. The nested
code was then re-ordered as needed to compile, i.e. stats may not show
this is being a "pure" move despite there not being any intended changes
in functionality.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Exposing only the function allows @nested, i.e. the module param, to be
statically defined in vmx.c, ensuring we aren't unnecessarily checking
said variable in the nested code. nested_vmx_allowed() is exposed due
to the need to verify nested support in vmx_{get,set}_nested_state().
The downside is that nested_vmx_allowed() likely won't be inlined in
vmx_{get,set}_nested_state(), but that should be a non-issue as they're
not a hot path. Keeping vmx_{get,set}_nested_state() in vmx.c isn't a
viable option as they need access to several nested-only functions.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
...as they're used directly by the nested code. This will allow
moving the bulk of the nested code out of vmx.c without concurrent
changes to vmx.h.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Exposed vmx_msr_index, vmx_return and host_efer via vmx.h so that the
nested code can be moved out of vmx.c.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
...so that the function doesn't need to be created when moving the
nested code out of vmx.c.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
...so that it doesn't need access to @nested. The only case where the
provided struct isn't already zeroed is the call from vmx_create_vcpu()
as setup_vmcs_config() zeroes the struct in the other use cases. This
will allow @nested to be statically defined in vmx.c, i.e. this removes
the last direct reference from nested code.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
...in nested-specific code so that they can eventually be moved out of
vmx.c, e.g. into nested.c.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
...so that future patches can reference e.g. @kvm_vmx_exit_handlers
without having to simultaneously move a big chunk of code. Speaking
from experience, resolving merge conflicts is an absolute nightmare
without pre-moving the code.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Eventually this will allow us to move the nested VMX code out of vmx.c.
Note that this also effectively wraps @enable_shadow_vmcs with @nested
so that it too can be moved out of vmx.c.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VMX has a few hundred lines of code just to wrap various VMX specific
instructions, e.g. VMWREAD, INVVPID, etc... Move them to a dedicated
header so it's easier to find/isolate the boilerplate.
With this change, more inlines can be moved from vmx.c to vmx.h.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The header, evmcs.h, already exists and contains a fair amount of code,
but there are a few pieces in vmx.c that can be moved verbatim. In
addition, move an array definition to evmcs.c to prepare for multiple
consumers of evmcs.h.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
vmcs12 is the KVM-defined struct used to track a nested VMCS, e.g. a
VMCS created by L1 for L2.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This isn't intended to be a pure reflection of hardware, e.g. struct
loaded_vmcs and struct vmcs_host_state are KVM-defined constructs.
Similar to capabilities.h, this is a standalone file to avoid circular
dependencies between yet-to-be-created vmx.h and nested.h files.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Expose the variables associated with various module params that are
needed by the nested VMX code. There is no ulterior logic for what
variables are/aren't exposed, this is purely "what's needed by the
nested code".
Note that @nested is intentionally not exposed.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Defining a separate capabilities.h as opposed to putting this code in
e.g. vmx.h avoids circular dependencies between (the yet-to-be-added)
vmx.h and nested.h. The aforementioned circular dependencies are why
struct nested_vmx_msrs also resides in capabilities instead of e.g.
nested.h.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
...instead of referencing the global struct. This will allow moving
setup_vmcs_config() to a separate file that may not have access to
the global variable. Modify nested_vmx_setup_ctls_msrs() appropriately
since vmx_capability.ept may not be accurate when called by
vmx_check_processor_compat().
No functional change intended.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
EFER and PERF_GLOBAL_CTRL MSRs have dedicated VM Entry/Exit controls
that KVM dynamically toggles based on whether or not the guest's value
for each MSRs differs from the host. Handle the dynamic behavior by
adding a helper that clears the dynamic bits so the bits aren't set
when initializing the VMCS field outside of the dynamic toggling flow.
This makes the handling consistent with similar behavior for other
controls, e.g. pin, exec and sec_exec. More importantly, it eliminates
two global bools that are stealthily modified by setup_vmcs_config.
Opportunistically clean up a comment and print related to errata for
IA32_PERF_GLOBAL_CTRL.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
MSR_IA32_XSS has no relation to the VMCS whatsoever, it doesn't belong
in setup_vmcs_config() and its reference to host_xss prevents moving
setup_vmcs_config() to a dedicated file.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VMX specific files now reside in a dedicated subdirectory, i.e. the
file name prefix is redundant.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VMX specific files now reside in a dedicated subdirectory. Drop the
"vmx" prefix, which is redundant, and add a "vmcs" prefix to clarify
that the file is referring to VMCS shadow fields.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
...to prepare for shattering vmx.c into multiple files without having
to prepend "vmx_" to all new files.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
