Required to enable correct wait_for_atomic checks.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
This is unusual. Usually IDs listed on early stages of platform
definition are kept there as reserved for later use.
However these IDs here are not listed anymore in any of steppings
and devices IDs tables for Kabylake on configurations overview
section of BSpec.
So it is better removing them before they become used in any
other future platform.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466718636-19675-2-git-send-email-rodrigo.vivi@intel.com
Since wait_for_atomic doesn't re-check the wait-for condition after
expiry of the timeout it can fail when called from non-atomic context
even if the condition is set correctly before the expiry. Fix this by
using the non-atomic wait_for instead.
Due to the relatively long 10ms timeout, probably this didn't cause any
real problems, but fix it in any case for consistency.
Fixes: 0351b93992 ("drm/i915: Do not lie about atomic timeout granularity")
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
CC: drm-intel-fixes@lists.freedesktop.org
Link: http://patchwork.freedesktop.org/patch/msgid/1467110253-16046-5-git-send-email-imre.deak@intel.com
Since wait_for_atomic doesn't re-check the wait-for condition after
expiry of the timeout it can fail when called from non-atomic context
even if the condition is set correctly before the expiry. Fix this by
using the non-atomic wait_for instead.
Fixes: 0351b93992 ("drm/i915: Do not lie about atomic timeout granularity")
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
CC: drm-intel-fixes@lists.freedesktop.org
Link: http://patchwork.freedesktop.org/patch/msgid/1467110253-16046-4-git-send-email-imre.deak@intel.com
Since wait_for_atomic doesn't re-check the wait-for condition after
expiry of the timeout it can fail when called from non-atomic context
even if the condition is set correctly before the expiry. Fix this by
using the non-atomic wait_for instead.
Fixes: 0351b93992 ("drm/i915: Do not lie about atomic timeout granularity")
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
CC: drm-intel-fixes@lists.freedesktop.org
Link: http://patchwork.freedesktop.org/patch/msgid/1467110253-16046-3-git-send-email-imre.deak@intel.com
Since wait_for_atomic doesn't re-check the wait-for condition after
expiry of the timeout it can fail when called from non-atomic context
even if the condition is set correctly before the expiry. Fix this by
using the non-atomic wait_for instead.
I noticed this via the PLL locking timing out incorrectly, with this fix
I couldn't reproduce the problem.
Fixes: 0351b93992 ("drm/i915: Do not lie about atomic timeout granularity")
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
CC: drm-intel-fixes@lists.freedesktop.org
Link: http://patchwork.freedesktop.org/patch/msgid/1467110253-16046-2-git-send-email-imre.deak@intel.com
When a display update triggers a DDB re-allocation, we should start by
assuming that only the updated pipes need to be re-allocated (we have
logic later that may add additional pipes if, e.g., a modeset triggers a
change to the global allocation).
We were erroneously using the _active_ pipes as our starting point
rather than the changed pipes. This causes us to grab CRTC locks that
we didn't actually need, reducing parallelism. Given the recent
non-blocking atomic changes, it also causes legacy pageflips against one
CRTC to return -EBUSY if there's an outstanding pageflip against a
different CRTC (a situation easily triggered via compositors like
Weston).
Fixes: 98d39494d3 ("drm/i915/gen9: Compute DDB allocation at atomic check time (v4)")
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467070964-14864-1-git-send-email-matthew.d.roper@intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fix build errors when ACPI is not enabled by adding function stubs:
../drivers/gpu/drm/i915/i915_drv.c: In function 'i915_drm_suspend':
../drivers/gpu/drm/i915/i915_drv.c:635:2: error: implicit declaration of function 'intel_opregion_unregister' [-Werror=implicit-function-declaration]
intel_opregion_unregister(dev_priv);
../drivers/gpu/drm/i915/i915_drv.c: In function 'i915_drm_resume':
../drivers/gpu/drm/i915/i915_drv.c:798:2: error: implicit declaration of function 'intel_opregion_register' [-Werror=implicit-function-declaration]
intel_opregion_register(dev_priv);
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Fixes: 03d92e4779 ("drm/i915/opregion: Rename init/fini functions to register/unregister")
Cc: drm-intel-fixes@lists.freedesktop.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[Jani: dropped the stale init/fini declarations]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467028399-9965-1-git-send-email-jani.nikula@intel.com
Load specific firmware versions for the DMC instead of using symbolic
links. The currently recommended versions are: SKL 1.26, KBL 1.01 and
BXT 1.07.
Certain DMC versions need workarounds in the driver which forces us to
have a tight dependency between firmware and driver. In order to be able
to provide a tested and known working configuration we must lock down on
a specific DMC firmware version.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463391057-32350-1-git-send-email-patrik.jakobsson@linux.intel.com
If a context waiting for VBlank were switched out, switching
in the next context and generating a CSB event in the process,
then the GuC would have to put the context back in the queue,
and then observe the subsequent VBlank interrupt so that it
could resubmit the suspended context.
However, we always set the CTX_CTRL_INHIBIT_SYN_CTX_SWITCH bit
in the RING_CONTEXT_CONTROL register, so this case cannot occur.
Furthermore we don't use the GuC's internal scheduler or allow
it to auto-resubmit workloads. Consequently, the GuC doesn't
need to see VBlanks, and by sending them to it we may be waking
it up unnecessarily, which might reduce RC6 residency and
increase power consumption.
So this patch removes the setting of the GFC_FORWARD_VBLANK
field from the code that diverts interrupts towards the GuC.
(The code to direct interrupts to the host, OTOH, continues to
explicitly set the field to "never send VBlanks to the GuC".)
v3:
Remove the line of code completely (original set the field
to ALWAYS forward, v1 changed it to CONDITIONAL forwarding,
v2 explicitly set it to NEVER, v3 just doesn't touch it at
all, as we know it's already set to NEVER).
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (previous version)
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466780277-23435-1-git-send-email-david.s.gordon@intel.com
Gen8 versions of these macros were updated a few months ago
(e8ebd8e drm/i915: eliminate 'temp' in gen8_for_each macros)
originally because at least one iterator could generate an
out of bounds access, but also because eliminating the 'temp'
parameter generated smaller and faster code.
Matthew Auld recently noticed the same problem with the gen6
versions and provided a patch
https://lists.freedesktop.org/archives/intel-gfx/2016-June/099334.html
but while we're changing these, we might as well make them as
much like the gen8 versions as possible, including the style
of using "&& (..., true)" rather than ": (..., 1) : 0", and
of course eliminating the redundant 'temp'.
Furthermore, the "all_pdes" version is only used in one place,
so we can improve code efficiency by changing both the macro
parameters and the calling code to reduce extra dereferences.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466793466-23500-1-git-send-email-david.s.gordon@intel.com
The contexts only pin space within the global GTT. Therefore forcing the
switch to the perma-pinned kernel context only has an effect when trying
to evict from and find room within the global GTT. We can then restrict
the switch to only when operating on the default context. This is mostly
a no-op as full-ppgtt only exists with execlists at present which skips
the context switch anyway.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466776558-21516-7-git-send-email-chris@chris-wilson.co.uk
We only need to force a switch to the kernel context placeholder during
eviction. All other uses of i915_gpu_idle() just want to wait until
existing work on the GPU is idle. Rename i915_gpu_idle() to
i915_gem_wait_for_idle() to avoid any implications about "parking" the
context first.
v2: Tweak an error message if the wait fails for the ilk vtd w/a
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466776558-21516-6-git-send-email-chris@chris-wilson.co.uk
As the L3 remapping is applied before the next execution, there is no
need to wait until all previous uses are idle, the application will not
occur any sooner.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466776558-21516-5-git-send-email-chris@chris-wilson.co.uk
When the GPU is reset or state lost through suspend, every default
legacy context needs to reload their state - both the golden render
state and the L3 mapping. Only context images explicitly saved to memory
(i.e. all execlists and non-default legacy contexts) will retain their
state across the reset.
v2: Rebase
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466776558-21516-4-git-send-email-chris@chris-wilson.co.uk
The kernel context exists simply as a placeholder and should never be
executed with a render context. It does not need the golden render
state, as that will always be applied to a user context. By skipping the
initialisation we can avoid issues in attempting to program the golden
render context when trying to make the hardware idle.
v2: Rebase
Testcase: igt/drm_module_reload_basic #byt
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=95634
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466776558-21516-3-git-send-email-chris@chris-wilson.co.uk
This is so that we have symmetry with intel_lrc.c and avoid a source of
if (i915.enable_execlists) layering violation within i915_gem_context.c -
that is we move the specific handling of the dev_priv->kernel_context
for legacy submission into the legacy submission code.
This depends upon the init/fini ordering between contexts and engines
already defined by intel_lrc.c, and also exporting the context alignment
required for pinning the legacy context.
v2: Separate out pin/unpin context funcs for greater symmetry with
intel_lrc. One more step towards unifying behaviour between the two
classes of engines and towards fixing another bug in i915_switch_context
vs requests.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466776558-21516-2-git-send-email-chris@chris-wilson.co.uk
During suspend (or module unload), if we have never accessed the engine
(i.e. userspace never submitted a batch to it), the engine is idle. Then
we attempt to idle the engine by forcing it to the default context,
which actually means we submit a render batch to setup the golden
context state and then wait for it to complete. We can skip this
entirely as we know the engine is idle.
v2: Drop incorrect comment.
References: https://bugs.freedesktop.org/show_bug.cgi?id=95634
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466776558-21516-1-git-send-email-chris@chris-wilson.co.uk
The module init/exit routines are a wrapper around the PCI device
init/exit, so move them across.
Note that in order to avoid exporting the driver struct, instead of
manipulating driver.features inside i915_init we instead opt to simply
exit if i915.modeset is disabled.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466773227-7994-15-git-send-email-chris@chris-wilson.co.uk
The GETPARAM ioctl writes to a user supplied address. If that address is
invalid, it is the user's error and not the driver's, so quietly report
EFAULT and don't blame ourselves with a DRM_ERROR.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466773227-7994-11-git-send-email-chris@chris-wilson.co.uk
i915_dma.c used to contain the DRI1/UMS horror show, but now all that
remains are the out-of-place driver level interfaces (such as
allocating, initialising and registering the driver). These should be in
i915_drv.c alongside similar routines for suspend/resume.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466773227-7994-10-git-send-email-chris@chris-wilson.co.uk
drm_connector_register_all() is now automatically called by
drm_dev_register(), and so we no longer have to do so ourselves (via
intel_modeset_register() after calling drm_dev_register()). Similarly
for unregistering.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466773227-7994-8-git-send-email-chris@chris-wilson.co.uk
To complete the transition to manual control of load/unload, we need to
take over unloading from i915_pci_remove(). This allows us to correctly
order our unregister vs shutdown phases, which currently are inverted
due to the midlayer.
However, the unload sequence is still invalid as we shutdown the driver
with the last reference. Ideally, all we want to do is remove the
userspace access on device removal, deferring the cleanup to the
drm_dev_release() - breaking the reference cycles is then left as an
exercise for the reader.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466773227-7994-7-git-send-email-chris@chris-wilson.co.uk
Take control over allocating, loading and registering the driver from the
DRM midlayer by performing it manually from i915_pci_probe. This allows
us to carefully control the order of when we setup the hardware vs when
it becomes visible to third parties (including userspace). The current
ordering makes the driver visible to userspace first (in order to
coordinate with removed DRI1 userspace), but that ordering incurs risk.
The risk increases as we strive for more asynchronous loading.
One side effect of controlling the allocation is that we can allocate
both the drm_device + drm_i915_private in one block, the next step
towards subclassing.
Unload is still left as before, a mix of midlayer and driver.
v2: After drm_dev_init(), we should call drm_dev_unref() so that we call
drm_dev_release() and free everything from drm_dev_init().
v3: Fixup missed error code for failing to allocate dev_priv
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466773227-7994-6-git-send-email-chris@chris-wilson.co.uk
Currently debugfs files are created before the driver is even loads.
This gives the opportunity for userspace to open that interface and poke
around before the backing data structures are initialised - with the
possibility of oopsing or worse.
Move the creation of the debugfs files to our registration phase, where
we announce our presence to the world when we are ready, i.e the
sequence changes from
drm_dev_register()
-> drm_minor_register()
-> drm_debugfs_init()
-> i915_debugfs_init()
-> i915_driver_load()
to
drm_dev_register()
-> drm_minor_register()
-> drm_debugfs_init()
-> i915_driver_load()
-> i915_debugfs_register()
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466773227-7994-5-git-send-email-chris@chris-wilson.co.uk
Currently the backlight is being registered in the load phase (before
the display and its objects are registered). Move the backlight
registration into the analogous phase by performing it from the
connector registration, just after its creation.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466773227-7994-3-git-send-email-chris@chris-wilson.co.uk
With the introduction of a connector->func for callback from
drm_connector_register() we can move all the tasks that we want to do
upon registration into that callback. Later, this will allow us to
reorder the registration and defer it until after the device is setup
and ready for userspace.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466773227-7994-2-git-send-email-chris@chris-wilson.co.uk
Currently setting up the backlight for a panel is sometimes done
together with initialising the panel, and sometimes after the connector
is registered. The backlight setup does not depend upon connector
registration (i.e. access to sysfs/debugfs and the kobject hierachy) so
perform it consistently just after panel initialisation.
Note the discrepancy here as destroying the panel is done during
connector unregistration...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466773227-7994-1-git-send-email-chris@chris-wilson.co.uk
Effectively removes one layer of indirection between the mask of
possible engines and the engine constructors. Instead of spelling
out in code the mapping of HAS_<engine> to constructors, makes
more use of the recently added data driven approach by putting
engine constructor vfuncs into the table as well.
Effect is fewer lines of source and smaller binary.
At the same time simplify the error handling since engine
destructors can run on unitialized engines anyway.
Similar approach could be done for legacy submission is wanted.
v2: Removed ugly BUILD_BUG_ONs in favour of newly introduced
ENGINE_MASK and HAS_ENGINE macros.
Also removed the forward declarations by shuffling functions
around.
v3: Warn when logical_rings table does not contain enough data
and disable the engines which could not be initialized.
(Chris Wilson)
v4: Chris Wilson suggested a nicer engine init loop.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1466689961-23232-1-git-send-email-tvrtko.ursulin@linux.intel.com
Backmerge drm-next for the reworked device register/unregistering.
Chris Wilson needs that to be able to land his i915 load/unload
demidlayering.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
- device tree binding documentation for MT8173 HDMI encoder, CEC, DDC,
and PHY
- drivers for MT8173 HDMI encoder, CEC (HPD only for now), DDC, and PHY
- enable HDMI output via a custom SMCCC call
- add ddc-i2c-bus property to HDMI connector device tree binding
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1TLt
-----END PGP SIGNATURE-----
Merge tag 'mediatek-drm-2016-06-20' of git://git.pengutronix.de/git/pza/linux into drm-next
MT8173 HDMI support
- device tree binding documentation for MT8173 HDMI encoder, CEC, DDC,
and PHY
- drivers for MT8173 HDMI encoder, CEC (HPD only for now), DDC, and PHY
- enable HDMI output via a custom SMCCC call
- add ddc-i2c-bus property to HDMI connector device tree binding
* tag 'mediatek-drm-2016-06-20' of git://git.pengutronix.de/git/pza/linux:
dt-bindings: hdmi-connector: add DDC I2C bus phandle documentation
drm/mediatek: enable hdmi output control bit
drm/mediatek: Add HDMI support
dt-bindings: drm/mediatek: Add Mediatek HDMI dts binding
some rcar-du fixes.
* 'drm/next/du' of git://linuxtv.org/pinchartl/media:
drm: rcar-du: error message is not needed for EPROBE_DEFER
drm: rcar-du: error message is not needed for drm_vblank_init()
rcar-du: add/rename DEFR6 TCON bits
- Infrastructure for GVT-g (paravirtualized gpu on gen8+), from Zhi Wang
- another attemp at nonblocking atomic plane updates
- bugfixes and refactoring for GuC doorbell code (Dave Gordon)
- GuC command submission enabled by default, if fw available (Dave Gordon)
- more bxt w/a (Arun Siluvery)
- bxt phy improvements (Imre Deak)
- prep work for stolen objects support (Ankitprasa Sharma & Chris Wilson)
- skl/bkl w/a update from Mika Kuoppala
- bunch of small improvements and fixes all over, as usual
* tag 'drm-intel-next-2016-06-20' of git://anongit.freedesktop.org/drm-intel: (81 commits)
drm/i915: Update DRIVER_DATE to 20160620
drm/i915: Introduce GVT context creation API
drm/i915: Support LRC context single submission
drm/i915: Introduce execlist context status change notification
drm/i915: Make addressing mode bits in context descriptor configurable
drm/i915: Make ring buffer size of a LRC context configurable
drm/i915: gvt: Introduce the basic architecture of GVT-g
drm/i915: Fold vGPU active check into inner functions
drm/i915: Use offsetof() to calculate the offset of members in PVINFO page
drm/i915: Factor out i915_pvinfo.h
drm/i915: Serialise presentation with imported dmabufs
drm/i915: Use atomic commits for legacy page_flips
drm/i915: Move fb_bits updating later in atomic_commit
drm/i915: nonblocking commit
Reapply "drm/i915: Pass atomic states to fbc update, functions."
drm/i915: Roll out the helper nonblock tracking
drm/i915: Signal drm events for atomic
drm/i915/ilk: Don't disable SSC source if it's in use
drm/i915/guc: (re)initialise doorbell h/w when enabling GuC submission
drm/i915/guc: replace assign_doorbell() with select_doorbell_register()
...
Again a pile of things all over
- Conversion to rst from docbook from Jani. Looks real pretty, and the
source is now actually readable (compared to horrible, horrible docbook
xml)! https://01.org/linuxgraphics/gfx-docs/drm/
- device register/unregister rework from Chris, with follow-up work from
Benjamin. Allows more drivers to demidlayer load/unload and others to
remove a bit of boilerplate.
- master/auth related cleanup, with docs
- some dma-buf polish, merged by Sumit
- small stuff all over (like build fixes from Arnd)
Group maintainership seems to slowly take off, with both Thierry and Sumit
pushing a few things. No hiccups thus far.
* tag 'topic/drm-misc-2016-06-22-updated' of git://anongit.freedesktop.org/drm-intel: (68 commits)
drm/vc4: Remove unused connector
drm/fb-helper: Reduce READ_ONCE(master) to lockless_dereference
drm/sun4i: Remove open-coded drm_connector_register_all()
drm/vc4: Remove open-coded drm_connector_register_all()
drm/atmel-hlcdc: Remove redundant call to drm_connector_unregister_all()
drm: document drm_auth.c
drm: Clear up master tracking booleans
drm: Extract drm_is_current_master
drm: Refactor drop/set master code a bit
drm: Lobotomize set_busid nonsense for !pci drivers
drm: Nuke SET_UNIQUE ioctl
drm: Don't call drm_dev_set_unique from platform drivers
drm/vgem: Stop calling drm_drv_set_unique
drm: Use dev->name as fallback for dev->unique
drm: Clean up drm_crtc.h
drm: Move master pointer from drm_minor to drm_device
drm: sti: rework init sequence
drm: sti: use late_register and early_unregister callbacks
drm/amdkfd: Clean up inline handling
drm: Add callbacks for late registering
...
During hibernation the cached DP port register value will be left with
whatever value we have there when we create the hibernation image.
Currently that means the port (and eDP PLL) will be off in the cached
value. However when we resume there is no guarantee that the value
in the actual register will match the cached value. If i915 isn't
loaded in the kernel that loads the hibernation image, the port may
well be on (eg. left on by the BIOS). The encoder state readout
does the right thing in this case and updates our encoder state
to reflect the actual hardware state. However the post-resume modeset
will then use the stale cached port register value in
intel_dp_link_down() and potentially confuse the hardware.
This was caught by the following assert
WARNING: CPU: 3 PID: 5288 at ../drivers/gpu/drm/i915/intel_dp.c:2184 assert_edp_pll+0x99/0xa0 [i915]
eDP PLL state assertion failure (expected on, current off)
on account of the eDP PLL getting prematurely turned off when
shutting down the port, since the DP_PLL_ENABLE bit wasn't set
in the cached register value.
Presumably I introduced this problem in
commit 6fec766283 ("drm/i915: Use intel_dp->DP in eDP PLL setup")
as before that we didn't update the cached value after shuttting the
port down. That's assuming the port got enabled at least once prior
to hibernating. If that didn't happen then the cached value would
still have been totally out of sync with reality (eg. first boot w/o
eDP on, then hibernate, and then resume with eDP on).
So, let's fix this properly and refresh the cached register value from
the hardware register during resume.
DDI platforms shouldn't use the cached value during port disable at
least, so shouldn't have this particular issue. They might still have
issues if we skip the initial modeset and then try to retrain the link
or something. But untangling this DP vs. DDI mess is a bigger topic,
so let's jut punt on DDI for now.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Fixes: 6fec766283 ("drm/i915: Use intel_dp->DP in eDP PLL setup")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463162036-27931-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
The wait for panel status helper will only function correctly if the
HW panel timings are programmed correctly. Returning prematurely from
this helper may lead to obscure bugs later, so sanity check the HW
timing registers.
v2:
- Check the T8, T9 fields too, we do program them (Ville)
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466096506-11937-1-git-send-email-imre.deak@intel.com
The PPS registers are backed by power well #0 and as such may be reset
after system or runtime suspend (both implying a possible DC9
transition). Fix this by reusing the VLV/CHV PPS pipe-reassignment
logic. The difference on BXT is that the PPS instances are not pipe but
port (or more accurately pin) specific, so we only need to care about
the lost HW state. As opposed to VLV/CHV the SW state is fixed and
initialized during connector init.
This also paves the way towards using the actual port->PPS instance
mapping based on VBT.
This fixes eDP link training errors on BXT after suspend, where we
started the link training too early due to an incorrect T3 (panel power
on) register value.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96436
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466084243-5388-2-git-send-email-imre.deak@intel.com
Move the early PPS initialization calls next to the rest of PPS
initialization steps. This allows us to forgo a duplicated call to
intel_dp_init_panel_power_sequencer_registers() on VLV/CHV.
This will swap the order of DP AUX registration wrt. PPS initialization.
There is an existing race here in case of a user space access via the
DPAUX device node after DP AUX registration and before calling
intel_dp_init_panel_power_sequencer_registers(), but this change won't
make this worse. The fix for this is to separate DP AUX initialization
and registration, that's a separate work already underway.
The order of MST wrt. PPS init as well as the order of
intel_dp_init_panel_power_sequencer_registers() wrt.
intel_edp_panel_vdd_sanitize() also swap, which is ok, there are no
dependencies between these steps.
Suggested by Ville.
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466499109-20240-4-git-send-email-imre.deak@intel.com
