Ensure that we supply the same phy interface mode to mac_link_down() as
we did for the corresponding mac_link_up() call. This ensures that MAC
drivers that use the phy interface mode in these methods can depend on
mac_link_down() always corresponding to a mac_link_up() call for the
same interface mode.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Clear up some recent tipc regressions because of registration
ordering. Fix from Junwei Hu.
2) tipc's TLV_SET() can read past the end of the supplied buffer during
the copy. From Chris Packham.
3) ptp example program doesn't match the kernel, from Richard Cochran.
4) Outgoing message type fix in qrtr, from Bjorn Andersson.
5) Flow control regression in stmmac, from Tan Tee Min.
6) Fix inband autonegotiation in phylink, from Russell King.
7) Fix sk_bound_dev_if handling in rawv6_bind(), from Mike Manning.
8) Fix usbnet crash after disconnect, from Kloetzke Jan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
usbnet: fix kernel crash after disconnect
selftests: fib_rule_tests: use pre-defined DEV_ADDR
net-next: net: Fix typos in ip-sysctl.txt
ipv6: Consider sk_bound_dev_if when binding a raw socket to an address
net: phylink: ensure inband AN works correctly
usbnet: ipheth: fix racing condition
net: stmmac: dma channel control register need to be init first
net: stmmac: fix ethtool flow control not able to get/set
net: qrtr: Fix message type of outgoing packets
networking: : fix typos in code comments
ptp: Fix example program to match kernel.
fddi: fix typos in code comments
selftests: fib_rule_tests: enable forwarding before ipv4 from/iif test
selftests: fib_rule_tests: fix local IPv4 address typo
tipc: Avoid copying bytes beyond the supplied data
2/2] net: xilinx_emaclite: use readx_poll_timeout() in mdio wait function
1/2] net: axienet: use readx_poll_timeout() in mdio wait function
vlan: Mark expected switch fall-through
macvlan: Mark expected switch fall-through
net/mlx4_en: ethtool, Remove unsupported SFP EEPROM high pages query
...
Do not update the link interface mode while the link is down to avoid
spurious link interface changes.
Always call mac_config if we have a PHY to propagate the pause mode
settings to the MAC.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are series of patches that add SPDX tags to different kernel files,
based on two different things:
- SPDX entries are added to a bunch of files that we missed a year ago
that do not have any license information at all.
These were either missed because the tool saw the MODULE_LICENSE()
tag, or some EXPORT_SYMBOL tags, and got confused and thought the
file had a real license, or the files have been added since the last
big sweep, or they were Makefile/Kconfig files, which we didn't
touch last time.
- Add GPL-2.0-only or GPL-2.0-or-later tags to files where our scan
tools can determine the license text in the file itself. Where this
happens, the license text is removed, in order to cut down on the
700+ different ways we have in the kernel today, in a quest to get
rid of all of these.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
The reason for these "large" patches is if we were to continue to
progress at the current rate of change in the kernel, adding license
tags to individual files in different subsystems, we would be finished
in about 10 years at the earliest.
There will be more series of these types of patches coming over the next
few weeks as the tools and reviewers crunch through the more "odd"
variants of how to say "GPLv2" that developers have come up with over
the years, combined with other fun oddities (GPL + a BSD disclaimer?)
that are being unearthed, with the goal for the whole kernel to be
cleaned up.
These diffstats are not small, 3840 files are touched, over 10k lines
removed in just 24 patches.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXOP8uw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynmGQCgy3evqzleuOITDpuWaxewFdHqiJYAnA7KRw4H
1KwtfRnMtG6dk/XaS7H7
=O9lH
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull SPDX update from Greg KH:
"Here is a series of patches that add SPDX tags to different kernel
files, based on two different things:
- SPDX entries are added to a bunch of files that we missed a year
ago that do not have any license information at all.
These were either missed because the tool saw the MODULE_LICENSE()
tag, or some EXPORT_SYMBOL tags, and got confused and thought the
file had a real license, or the files have been added since the
last big sweep, or they were Makefile/Kconfig files, which we
didn't touch last time.
- Add GPL-2.0-only or GPL-2.0-or-later tags to files where our scan
tools can determine the license text in the file itself. Where this
happens, the license text is removed, in order to cut down on the
700+ different ways we have in the kernel today, in a quest to get
rid of all of these.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers.
The reason for these "large" patches is if we were to continue to
progress at the current rate of change in the kernel, adding license
tags to individual files in different subsystems, we would be finished
in about 10 years at the earliest.
There will be more series of these types of patches coming over the
next few weeks as the tools and reviewers crunch through the more
"odd" variants of how to say "GPLv2" that developers have come up with
over the years, combined with other fun oddities (GPL + a BSD
disclaimer?) that are being unearthed, with the goal for the whole
kernel to be cleaned up.
These diffstats are not small, 3840 files are touched, over 10k lines
removed in just 24 patches"
* tag 'spdx-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (24 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 25
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 24
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 23
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 22
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 21
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 20
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 19
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 18
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 17
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 15
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 14
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 13
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 12
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 11
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 10
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 9
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 7
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 5
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 4
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 3
...
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have EXPORT_.*_SYMBOL_GPL inside which was used in the
initial scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
XGMII interface mode no longer works on AQR107 after the recent changes,
adding back support.
Fixes: 570c8a7d53 ("net: phy: aquantia: check for supported interface modes in config_init")
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy id chosen by Amlogic is incorrectly set in the mdio mux and
does not match the phy driver.
It was not detected before because DT forces the use the correct driver
for the internal PHY.
Fixes: 7090425104 ("net: phy: add amlogic g12a mdio mux support")
Reported-by: Qi Duan <qi.duan@amlogic.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After calling phy_select_page() and until calling phy_restore_page(),
the mutex 'mdio_lock' is already locked, so the driver should use
non-locked version of phy functions. Or there will be a deadlock with
'mdio_lock'.
This replaces phy functions called from rtl8211e_config_init() to avoid
the deadlock issue.
Fixes: f81dadbcf7 ("net: phy: realtek: Add rtl8211e rx/tx delays config")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding missing callbacks I missed that one had them set already.
Interesting that the compiler didn't complain.
Fixes: daf3ddbe11 ("net: phy: realtek: add missing page operations")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing page operation callbacks to few Realtek drivers.
This also fixes a NPE after the referenced commit added code to the
RTL8211E driver that uses phy_select_page().
Fixes: f81dadbcf7 ("net: phy: realtek: Add rtl8211e rx/tx delays config")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reported-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's prone to problems if delay is cleared out for other than RGMII
modes. So lets set/clear the TX-delay in the config register only
if actually RGMII-like interface mode is requested. This only
concerns rtl8211f chips.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two chip pins named TXDLY and RXDLY which actually adds the 2ns
delays to TXC and RXC for TXD/RXD latching. Alas this is the only
documented info regarding the RGMII timing control configurations the PHY
provides. It turns out the same settings can be setup via MDIO registers
hidden in the extension pages layout. Particularly the extension page 0xa4
provides a register 0x1c, which bits 1 and 2 control the described delays.
They are used to implement the "rgmii-{id,rxid,txid}" phy-mode.
The hidden RGMII configs register utilization was found in the rtl8211e
U-boot driver:
https://elixir.bootlin.com/u-boot/v2019.01/source/drivers/net/phy/realtek.c#L99
There is also a freebsd-folks discussion regarding this register:
https://reviews.freebsd.org/D13591
It confirms that the register bits field must control the so called
configuration pins described in the table 12-13 of the official PHY
datasheet:
8:6 = PHY Address
5:4 = Auto-Negotiation
3 = Interface Mode Select
2 = RX Delay
1 = TX Delay
0 = SELRGV
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far we report symmetric pause only, and we don't consider the local
pause capabilities. Let's properly consider local and remote
capabilities, and report also asymmetric pause.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have valid scenarios where ETHTOOL_LINK_MODE_Pause_BIT doesn't
need to be supported. Therefore extend the first check to check
for rx_pause being set.
See also phy_set_asym_pause:
rx=0 and tx=1: advertise asym pause only
rx=0 and tx=0: stop advertising both pause modes
The fixed commit isn't wrong, it's just the one that introduced the
linkmode bitmaps.
Fixes: 3c1bcc8614 ("net: ethernet: Convert phydev advertize and supported from u32 to link mode")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I got an interesting report [0] that after resuming from hibernation
the link has 100Mbps instead of 1Gbps. Reason is that another OS has
been used whilst Linux was hibernated. And this OS speeds down the link
due to WoL. Therefore, when resuming, we shouldn't expect that what
the PHY advertises is what it did when hibernating.
Easiest way to do this is removing state PHY_RESUMING. Instead always
go via PHY_UP that configures PHY advertisement.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=202851
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When probing the phy device we set sym and asym pause in the "supported"
bitmap (unless the PHY tells us otherwise). However we don't know yet
whether the MAC supports pause. Simply copying phy->supported to
phy->advertising will trigger advertising pause, and that's not
what we want. Therefore add phy_advertise_supported() that copies all
modes but doesn't touch the pause bits.
In phy_support_(a)sym_pause we shouldn't set any bits in the supported
bitmap because we may set a bit the PHY intentionally disabled.
Effective pause support should be the AND-combined PHY and MAC pause
capabilities. If the MAC supports everything, then it's only relevant
what the PHY supports. If MAC supports sym pause only, then we have to
clear the asym bit in phydev->supported.
Copy the pause flags only and don't touch the modes, because a driver
may have intentionally removed a mode from phydev->advertising.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ8081 PHY has a factory test mode which is set at the de-assertion
of the reset line based on the RXER (KSZ8081RNA/RND) or TXC
(KSZ8081MNX/RNB) pin. If a pull-down is missing, or if the pin has a
pull-up, the factory test mode should be cleared by manually writing a 0
(according to the datasheet). This patch makes sure this factory test
bit is cleared in config_init().
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Considering that in polling mode each link drop will be latched,
settings can't have changed if link was up and is up.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
marvell_get_sset_count() returns how many statistics counters there
are. If the PHY supports fibre, there are 3, otherwise two.
marvell_get_strings() does not make this distinction, and always
returns 3 strings. This then often results in writing past the end
of the buffer for the strings.
Fixes: 2170fef78a ("Marvell phy: add field to get errors from fiber link.")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY's behave differently when being reset. Some reset registers to
defaults, some don't. Some trigger an autoneg restart, some don't.
So let's also set the autoneg restart bit when resetting. Then PHY
behavior should be more consistent. Clearing BMCR_ISOLATE serves the
same purpose and is borrowed from genphy_restart_aneg.
BMCR holds the speed / duplex settings in fixed mode. Therefore
we may have an issue if a soft reset resets BMCR to its default.
So better call genphy_setup_forced() afterwards in fixed mode.
We've seen no related complaint in the last >10 yrs, so let's
treat it as an improvement.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for VSC8514 in Microsemi driver (mscc.c)
with more features.
Signed-off-by: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VSC8514 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX,
1000BASE-X, can communicate with the MAC via QSGMII.
The MAC interface protocol for each port within QSGMII can
be either 1000BASE-X or SGMII, if the QSGMII MAC that the VSC8514 is
connecting to supports this functionality.
VSC8514 also supports SGMII MAC-side autonegotiation on each individual
port, downshifting, can set the blinking pattern of each of its 4 LEDs,
SyncE, 1000BASE-T Ring Resiliency as well as HP Auto-MDIX detection.
This adds support for 10BASE-T, 100BASE-TX, and 1000BASE-T,
QSGMII link with the MAC, downshifting, HP Auto-MDIX detection
and blinking pattern for its 4 LEDs.
The GPIO register bank is a set of registers that are common to all PHYs
in the package. So any modification in any register of this bank affects
all PHYs of the package.
If the PHYs haven't been reset before booting the Linux kernel and were
configured to use interrupts for e.g. link status updates, it is
required to clear the interrupts mask register of all PHYs before being
able to use interrupts with any PHY. The first PHY of the package that
will be init will take care of clearing all PHYs interrupts mask
registers. Thus, we need to keep track of the init sequence in the
package, if it's already been done or if it's to be done.
Most of the init sequence of a PHY of the package is common to all PHYs
in the package, thus we use the SMI broadcast feature which enables us
to propagate a write in one register of one PHY to all PHYs in the same
package.
Signed-off-by: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Co-developed-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing <of_device_id> table for SPI driver relying on SPI
device match since compatible is in a DT binding or in a DTS.
Before this patch:
modinfo drivers/net/phy/spi_ks8995.ko | grep alias
alias: spi:ksz8795
alias: spi:ksz8864
alias: spi:ks8995
After this patch:
modinfo drivers/net/phy/spi_ks8995.ko | grep alias
alias: spi:ksz8795
alias: spi:ksz8864
alias: spi:ks8995
alias: of:N*T*Cmicrel,ksz8795C*
alias: of:N*T*Cmicrel,ksz8795
alias: of:N*T*Cmicrel,ksz8864C*
alias: of:N*T*Cmicrel,ksz8864
alias: of:N*T*Cmicrel,ks8995C*
alias: of:N*T*Cmicrel,ks8995
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default m88e151x LED configuration is 0x1177, used LED[0]
for 1000M link, LED[1] for 100M link, and LED[2] for active.
But for some boards, which use LED[0] for link, and LED[1] for
active, prefer to be 0x1040. To be compatible with this case,
this patch defines a new dev_flag, and set it before connect
phy in HNS3 driver. When phy initializing, using the new
LED configuration if this dev_flag is set.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This renames the GPIO reset of mdio devices from 'reset' to
'reset_gpio' to better differentiate between GPIO and
reset-controller driven reset line.
Signed-off-by: David Bauer <mail@david-bauer.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds support for PHY reset pins handled by a reset controller.
Signed-off-by: David Bauer <mail@david-bauer.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_sanitize_settings() is called from phy_start_aneg() only, and only
if phydev->autoneg isn't set. Therefore the removed code does nothing.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In phy_device_create() we set phydev->autoneg = 1. This isn't changed
even if the PHY doesn't support autoneg. This seems to affect very
few PHY's, and they disable phydev->autoneg in their config_init
callback. So it's more of an improvement, therefore net-next.
The patch also wouldn't apply to older kernel versions because the
link mode bitmaps have been introduced recently.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Micrel KSZ9031 PHY may fail to establish a link when the Asymmetric
Pause capability is set. This issue is described in a Silicon Errata
(DS80000691D or DS80000692D), which advises to always disable the
capability. This patch implements the workaround by defining a KSZ9031
specific get_feature callback to force the Asymmetric Pause capability
bit to be cleared.
This fixes issues where the link would not come up at boot time, or when
the Asym Pause bit was set later on.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently genphy_read_abilities() has been added that dynamically detects
clause 22 PHY abilities. I *think* this detection should work with all
supported PHY's, at least for the ones with basic features sets, i.e.
PHY_BASIC_FEATURES and PHY_GBIT_FEATURES. So let's remove setting these
features explicitly and rely on phylib feature detection.
I don't have access to most of these PHY's, therefore I'd appreciate
regression testing.
v2:
- make the feature constant a comment so that readers know which
features are supported by the respective PHY
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If new PHY modes are added people may miss to update all relevant places
in the kernel. Therefore add a build bug check for new modes in enum
ethtool_link_mode_bit_indices that haven't been added to phylib yet.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently new modes have been added to ethtool.h, but the related
extension to phylib hasn't been done yet. So add support for these
modes.
v2:
- add missing 100Gbps and 50Gbps modes
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The definition of array settings[] is quite lengthy meanwhile. Add a
macro to shrink the definition.
v2:
- Fix an indentation issue
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
genphy_c45_aneg_done() is used by phylib as fallback for c45 PHY's if
callback aneg_done isn't defined. So we don't have to set this
explicitly. Same for genphy_c45_pma_read_abilities().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original patch didn't set phydev->autoneg_complete in one exit path.
Fix this.
Fixes: 4950c2ba49 ("net: phy: fix autoneg mismatch case in genphy_read_status")
Reported-by: Simon Horman <horms@verge.net.au>
Tested-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently a number of generic functions for Clause 45 PHY's has been
added. So let's replace the old very limited genphy_10g_driver with a
genphy_c45_driver. This driver isn't limited to 10G, however it's worth
to be noted that Clause 45 doesn't cover 1000Base-T. For using
1000Base-T with a Clause 45 PHY a dedicated PHY driver using vendor
registers is needed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
genphy_read_status() so far checks phydev->supported, not the actual
PHY capabilities. This can make a difference if the supported speeds
have been limited by of_set_phy_supported() or phy_set_max_speed().
It seems that this issue only affects the link partner advertisements
as displayed by ethtool. Also this patch wouldn't apply to older
kernels because linkmode bitmaps have been introduced recently.
Therefore net-next.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The purpose of this change is to align the gxl and g12a driver
declaration.
Like on the g12a variant, remove genphy_aneg_done() from the driver
declaration as the net phy framework will default to it anyway.
Also, the gxl phy id should be an exact match as well, so let's change
this and use the macro provided.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The g12a SoC family uses the type of internal PHY that was used on the
gxl family. The quirks of gxl family, like the LPA register corruption,
appear to have been resolved on this new SoC generation.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the mdio mux and internal phy glue of the g12a SoC family
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> # clk parts
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that phylib uses genphy_read_abilities() as fallback, we don't have
to set callback get_features any longer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Meanwhile we have generic functions for reading the abilities of
Clause 22 / 45 PHY's. This allows to use them as fallback in case
callback get_features isn't set. Benefit is the reduction of
boilerplate code in PHY drivers.
v2:
- adjust the comment in phy_driver_register to match the code
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original patch didn't consider the case that autoneg process
finishes successfully but both link partners have no mode in common.
In this case there's no link, nevertheless we may be interested in
what the link partner advertised.
Like phydev->link we set phydev->autoneg_complete in
genphy_update_link() and use the stored value in genphy_read_status().
This way we don't have to read register BMSR again.
Fixes: b6163f194c ("net: phy: improve genphy_read_status")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the 88x2110 PHY support was added, the suspend and resume callbacks
were forgotten. This patch adds them to the 88x2110 PHY callback
definition.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the suspend/resume callbacks for Marvell 10G PHYs. The
three PCS (base-t, base-r and 1000base-x) are set in low power (the PCS
are powered down) when the PHY isn't used.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link partner advertisement registers are not guaranteed to contain
valid values if autoneg is incomplete. Therefore, if
MDIO_AN_STAT1_COMPLETE isn't set, let's clear all link partner
capability bits. This also avoids unnecessary register reads if link
is down and phylib is in polling mode.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
