sama5d3 CPU modules embed a parallel NOR flash connected to the EBI bus.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Use the new EBI/NAND bindings to declare NAND chips and remove old NAND
nodes along the way.
Note that we keep using old bindings in at91rm9200.dtsi because this
SoC is not supported by the EBI driver.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Declare new nodes for the EBI and NAND controllers embedded in various
at91/sama5 SoCs.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
According to the binding documentation and the source code the atmel-gpio
controller takes IRQ_TYPE_* as its flags values, not GPIO_ACTIVE_*.
This patch uses the right variable type which yields the same result
when compiled. Note that this might be wrong and actually
IRQ_TYPE_LEVEL_LOW is intended by the dt author.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The gpio node has 144 gpios. Each gpio is capable of generating
an interrupt. Hence add interrupt-controller property to the gpio
node. With this in place one can use interrupts property in device
tree to request for the gpio interrupts.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This adds CPPI 4.1 DMA controller to USB OTG controller.
Changes since v2:
- Fixed the the property reg-names (had glue register defined)
- Removed few useless property
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add node for SPI NOR flash on orange-pi-zero board. Disable this node
by default and leave it to users to enable it if their board has
SPI NOR flash chip populated.
SPI NOR flash was optional in the first production batch in Dec 2016.
In later batches flash chip was pre-populated. However there should
be quite a few boards around which do not have flash chip.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The USB PHY can use either a GPIO pin or the PMIC's USB power supply
to sense VBUS. Since both options are available on the Cubietruck,
add the missing property for the USB power supply to the USB PHY node.
The device tree provides all usable options. Ultimately, which method
is used is up to the driver implementation.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The ACIN pins of the AXP221 PMIC on the A31 Hummingbird are tied to the
DC jack on the board through a 12V to 5V buck converter.
Enable the ACIN power supply.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The ACIN pins of the AXP209 PMIC on the Cubieboard are tied to the
DC jack on the board.
Enable the ACIN power supply.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The ACIN pins of the AXP209 PMIC on the Bananapi M1 Plus are tied to the
"power input" micro USB connector next to the SATA connector on the board.
Enable the ACIN power supply.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The ACIN pins of the AXP209 PMIC on the Cubieboard 2 are tied to the
DC jack on the board.
Enable the ACIN power supply.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
We want to keep node references in alphabetical order, except for
instances where node must be #included first.
Move the usb_otg node reference so that all references to non-AXP209
device nodes are in alphabetical order.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Two of the Ethernet switches on this board have EEPROMs connected.
Add the eeprom-length property to the device tree, making it possible
to access the EEPROM using ethtool -e.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch extends the L2 cache controller node for the Amlogic Meson8
and Meson8b SoCs with some missing parameters. These are taken from the
Amlogic GPL kernel source.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
[apply the change to Meson8 and Meson8b and updated description]
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Currently only meson6.dtsi and meson8.dtsi inherit the generic
meson.dtsi. However, since the Meson8b platform is basically a slightly
updated version of Meson8 we can safely inherit meson.dtsi. An indicator
for this are the nodes which are identical in meson.dtsi and
meson8b.dtsi (L2, gic, timer, uart_AO, uart_A, uart_B, uart_C).
Additionally this makes the following devices available on Meson8b which
were not avaialble before (however, since all affected drivers support
Meson6, Meson8 and the whole GX series there's no reason to assume that
they are not working):
- i2c_a and i2c_B
- the IR receiver
- SPFIC (SPI flash controller)
- the dwmac ethernet controller
Differences between Meson8 and Meson8b seem to be:
- ARM Cortex-A5 core instead of Cortex-A9 on Meson8
- dwmac on Meson8b supports RGMII
- small pinctrl updates
Inheriting meson.dtsi makes it easier to maintain by removing duplicate
definitions.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Amlogic Meson SoCs have most of the internal peripherals organized
in busses. Use them to make the dts easier to read and to avoid
duplicated register (bus) offset definitions.
The bus information is taken from the vendor kernel:
#define IO_CBUS_PHY_BASE 0xc1100000 ///2M
#define IO_AOBUS_PHY_BASE 0xc8100000 ///1M
There are more internal busses (such as the abp bus which seems to
contain audio, HDMI and Mali registers), but since we don't have
drivers for them yet these are not added (yet).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[khilman: minor whitespace fix]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Looks like nobody bothered to configure USB host for 37xx-evm
when we converted things to device tree, so let's add it. This
is similar to beagleboard configuration with few extra quirks
to configure the port. And as with beagleboard, OHCI won't work
because there is no USB LS/FS PHY. A HS USB hub is needed to use
devices like keyboard and mice.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As long as the kernel cmdline has "earlycon" in it, this allows
seeing debug messages earlier and does not require DEBUG_LL to
be enabled.
Acked-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As long as the kernel cmdline has "earlycon" in it, this allows
seeing debug messages earlier and does not require DEBUG_LL to
be enabled.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds the serial slave device for the WL1835 Bluetooth interface.
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the System Mailboxes 5 and 6 and the corresponding
child sub-mailbox (IPC 3.x) nodes for the AM571x IDK board.
This is needed to enable communication with the respective
remote processors IPU1, IPU2, and DSP1 from the MPU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the System Mailboxes 5 and 6 and the corresponding
child sub-mailbox (IPC 3.x) nodes for the AM572x IDK board.
This is needed to enable communication with the respective
remote processors IPU1, IPU2, DSP1 and DSP2 from the MPU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With two separate &gpmc nodes the second ranges property overwrites the
first. So put nand and ethernet in a single node and merge the ranges.
While at it also fix the ethernet suffix.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We don't need to bitbang these pins anymore, instead we muxed these
pins as SPI, after this change, done in commit 6c69f726, we introduced
the following error:
pinctrl-single 44e10800.pinmux: pin PIN85 already requested \
by 44e10800.pinmux; cannot claim for 48030000.spi
pinctrl-single 44e10800.pinmux: pin-85 (48030000.spi) status -22
Fixes: 6c69f726 ("ARM: dts: am335x-sl50: Enable SPI0 interface and Flash Memory")
Cc: <stable@vger.kernel.org> # 4.11
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The second version of the hardware moved the card detect pin from gpio0_6
to gpio1_9, as we won't support the first hardware version fix the pinmux
configuration of this pin.
Fixes: 8584d4fc ("ARM: dts: am335x-sl50: Add Toby-Churchill SL50 board support.")
Cc: <stable@vger.kernel.org> # 4.11
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Ethernet networking on K2L has been broken since v4.11-rc1. This was
caused by commit 32a34441a9 ("ARM: keystone: dts: fix netcp clocks
and add names"). This commit inadvertently moves on-chip static RAM
clock to the end of list of clocks provided for netcp. Since keystone
PM domain support does not have a list of recognized con_ids, only the
first clock in the list comes under runtime PM management. This means
the OSR (On-chip Static RAM) clock remains disabled and that broke
networking on K2L.
The OSR is used by QMSS on K2L as an external linking RAM. However this
is a standalone RAM that can be used for non-QMSS usage (as well as from
DSP side). So add a SRAM device node for the same and add the OSR clock
to the node.
Remove the now redundant OSR clock node from netcp.
To manage all clocks defined for netCP's use by runtime PM needs keystone
generic power domain (genpd) driver support which is under works.
Meanwhile, this patch restores K2L networking and is correct irrespective
of any future genpd work since OSR is an independent module and not part
of NetCP anyway.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
[nsekhar@ti.com: commit message updates, port to latest mainline]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Cc: stable@vger.kernel.org # for 4.11
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Identical to the setup on Koelsch.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
We currently have three device nodes for the same USB hardware
block, as evident by the reuse of the same reg address multiple
times. Now that the chipidea driver fully supports OTG with the
MSM wrapper we can collapse the three nodes into one USB device
node, reflecting the true nature of the hardware.
Since we're here, we also mark the irq trigger flags correctly,
as IRQ_TYPE_LEVEL_HIGH instead of IRQ_TYPE_NONE.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This USB controller has two phys, so add them both underneath the
ULPI bus, but only enable one of them based on the board
configuration. To get OTG to work, we need to add the id and vbus
detection info and also populate the regulators for the vbus
supply.
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
These regulators are controlled by the SPMI regulator driver
instead of the RPM regulator driver in the downstream android
kernel sources. Let's remove them from the DTS here because
they'll never be used by the RPM regulator driver.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
please pull the following:
- Phil provides a fix for the BCM283x (Raspberry Pi) by flagging the first
4KiB of physical memory as a reserved region in order to let the secondary
cores successfully spin until they are brought online
-----BEGIN PGP SIGNATURE-----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=x322
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.12/devicetree-fixes-2' of http://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for 4.12,
please pull the following:
- Phil provides a fix for the BCM283x (Raspberry Pi) by flagging the first
4KiB of physical memory as a reserved region in order to let the secondary
cores successfully spin until they are brought online
* tag 'arm-soc/for-4.12/devicetree-fixes-2' of http://github.com/Broadcom/stblinux:
ARM: dts: bcm283x: Reserve first page for firmware
Signed-off-by: Olof Johansson <olof@lixom.net>
Property 'enable-active-low' does not exist. Only 'enable-active-high' is
valid, and when this property is absent the gpio regulator will act as
active low by default.
So remove the unexisting 'enable-active-low' property.
Currently the GPIO flag is GPIO_ACTIVE_HIGH. In order to make
the dts description accurate, pass the GPIO_ACTIVE_LOW flag instead.
This change is safe because the gpio regulator driver does not take the
GPIO flag polarity into account.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Property 'enable-active-low' does not exist. Only 'enable-active-high' is
valid, and when this property is absent the gpio regulator will act as
active low by default.
So remove the unexisting 'enable-active-low' property.
Currently the GPIO flag is 0, which means active-high. In order to make
the dts description accurate, pass the GPIO_ACTIVE_LOW flag instead.
This change is safe because the gpio regulator driver does not take the
GPIO flag polarity into account.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently the following eMMC error is seen:
mmc1: mmc_select_hs200 failed, error -74
On imx7d-pico the eMMC VCCQ is fixed at 3.15V, so pass the 'no-1-8-v'
property to properly describe that 1.8V operation is not possible.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx7d-pico has the WDOG1_B pin connected to the PMIC, so add the
wdog1 node and use the 'fsl,ext-reset-output' property to
properly describe it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Most of DT files in ARM use #include "..." to make pre-processor
include DT in the same directory, but we have some exceptional files
that use #include <...> for that.
Fix them to remove -I$(srctree)/arch/$(SRCARCH)/boot/dts path from
dtc_cpp_flags.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
We have a clock controller for the Gemini SoC, so make use of the
driver and add clocks to the peripherals. Remove the hard-coded
frequency from the UART and add switch the timer compatible to the
generic that uses the clock framework for clock speed look-up.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the Gemini reset controller to the Gemini SoC
DTSI file and also adds the reset references to all existing
blocks already in the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Cubietruck Plus has an optical SPDIF out connector.
Enable SPDIF audio output for this board.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Cubietruck Plus has 4 LEDs in different colors.
Add device nodes for them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A83T SoC has an SPDIF transmitter block. According to the vendor
BSP kernel, it is compatible with the one found on the H3 SoC.
Add a device node and pinmux setting for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A83T SoC has a DMA controller that supports 8 DMA channels
to and from various peripherals.
Add a device node for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
"bcrmf" is a typo and "wifi" is the preferred form to describe
such node, so change it accordingly.
Reported-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add barebones dts support for TI's K2G Industrial Communication Engine evm.
This dts allows the board to boot using a ram based filesystem.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
With the new Keystone 2 Industrial Communication EVM adding the
unit address to the memory node it made sense to add it for this board
also.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Adding the unit address to the memory node was causing the below error:
Warning (reg_format): "reg" property in /memory has invalid length
(8 bytes) (#address-cells == 2, #size-cells == 2)
Further debugging showed that this was due to the memory node added by
default to skeleton.dtsi which was being included in keystone-k2g.dtsi.
Adding a missing node was all that was needed to remove this deprecated
dtsi file from the SoC dtsi. With skeleton.dtsi removed the dtc compiler
no longer complained about including the unit address for the memory node.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
"bcrmf" is a typo and "wifi" is the preferred form to describe
such node, so change it accordingly.
Reported-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently the following eMMC error is seen:
mmc1: mmc_select_hs200 failed, error -74
mmc1: new MMC card at address 0001
mmcblk1: mmc1:0001 V10008 7.05 GiB
mmcblk1boot0: mmc1:0001 V10008 partition 1 4.00 MiB
mmcblk1boot1: mmc1:0001 V10008 partition 2 4.00 MiB
mmcblk1rpmb: mmc1:0001 V10008 partition 3 4.00 MiB
On imx7s-warp the eMMC VCCQ is fixed at 3.15V, so pass the 'no-1-8-v'
property to properly describe that 1.8V operation is not possible.
With this change HS200 error is gone and another benefit is that the
card can operate in DDR52 mode now:
mmc1: new DDR MMC card at address 0001
mmcblk1: mmc1:0001 V10008 7.05 GiB
mmcblk1boot0: mmc1:0001 V10008 partition 1 4.00 MiB
mmcblk1boot1: mmc1:0001 V10008 partition 2 4.00 MiB
mmcblk1rpmb: mmc1:0001 V10008 partition 3 4.00 MiB
Suggested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the initial support for imx7d-pico board.
Add support for eMMC, USB host, USB device, PMIC, Ethernet and audio.
For more information about this board, please visit:
http://www.technexion.org/products/pico/pico-som/pico-imx7-emmc
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PWM driver has now capability to specify the PWM polarity
which is e.g. for backlight control. Allow to make use of PWM
polarity by specifying pwm-cells to be 3 in the base dt.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
List GPR block as compatible "fsl,imx6q-iomuxc-gpr" to support drivers
requesting it that way (PCIe driver is one example).
Cc: yurovsky@gmail.com
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that support for 'anatop-enable-bit' has been added to ANADIG
driver, reintroduce 'anatop-enable-bit' for all applicable LDOs.
Cc: yurovsky@gmail.com
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add reference to the Mali GPU device tree node on rk3288-veyron.
Tested on Minnie and Jerry boards.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add reference to the Mali GPU device tree node on rk3288-firefly.
Tested on Firefly board.
Signed-off-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add reference to the Mali GPU device tree node on the
rk3288-rock2-som platform. Tested on a Radxa Rock2 Square board.
Signed-off-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add Mali GPU device tree node for the rk3288 SoC, with devfreq
opp table.
Signed-off-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Property 'enable-active-low' does not exist. Only 'enable-active-high' is
valid, and when this property is absent the gpio regulator will act as
active low by default.
So remove the unexisting 'enable-active-low' property.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update freq of tsadc's working clock as 32768 hz, if not set, tsadc
will work at a default frequence.
Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds a new opp table for cpu on rk322x SoC.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Set sane default frequencies for CPLL, GPLL and some other core clocks
on the rk322x.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The datasheets for Allwinner SoCs set strict requirements on the
stability of the external crystal oscillators. Add the accuracy
for the main 24MHz oscillator to the device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we have support for the A83T CCU, add a device node for it,
and replace any existing placeholder clock phandles with the correct
ones.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A10s Olinuxino has an HDMI connector. Make sure we can use it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The A10s has an HDMI controller connected to the second TCON channel. Add
it to our DT.
Since the TV Encoder was the only channel 1 user so far, also add the
property now that we have several users.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[wens@csie.org: Replaced CLK_PLL_VIDEO[01]_2X with raw numbers for now
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
for various devices. Also included is a memory controller (GPMC) debug output
fix as without that the shown bootloader configured GPMC bus width will
be wrong and won't work for kernel timings:
- Add dra7 powerhold configuration to be able to shut down pmic correctly
- Fix polarity for gta04 mcbsp4 clocks for modem
- Fix Pandaboard CEC pin pull making it usable
- Fix LogicPD Torpedo camera pin mux
- Fix GPMC debug bus width
- Reduce cpu thermal shutdown temperature
-----BEGIN PGP SIGNATURE-----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=My0U
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.12/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.12-rc cycle most consisting of few minor dts fixes
for various devices. Also included is a memory controller (GPMC) debug output
fix as without that the shown bootloader configured GPMC bus width will
be wrong and won't work for kernel timings:
- Add dra7 powerhold configuration to be able to shut down pmic correctly
- Fix polarity for gta04 mcbsp4 clocks for modem
- Fix Pandaboard CEC pin pull making it usable
- Fix LogicPD Torpedo camera pin mux
- Fix GPMC debug bus width
- Reduce cpu thermal shutdown temperature
* tag 'omap-for-v4.12/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra7: Reduce cpu thermal shutdown temperature
memory: omap-gpmc: Fix debug output for access width
ARM: dts: LogicPD Torpedo: Fix camera pin mux
ARM: dts: omap4: enable CEC pin for Pandaboard A4 and ES
ARM: dts: gta04: fix polarity of clocks for mcbsp4
ARM: dts: dra7: Add power hold and power controller properties to palmas
Signed-off-by: Olof Johansson <olof@lixom.net>
- A fix on GPCv2 power domain driver Kconfig which causes a build
failure when CONFIG_PM is not set.
- Pull down PMIC IRQ pin for imx53-qsrb board to prevent spurious
PMIC interrupts from happening.
- Remove board level OPP override for imx6sx-sdb to fix a boot crash
seen on Rev.C boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZHav8AAoJEFBXWFqHsHzOPWMH/RP4LuJDUoFaPUJ3WsrMhPYR
qmBEzZXvjKBxImFCIiG09vcjQIiN9p5uZ9AqNIQGgoW20DlFKVZ0Rd64MJzp8QnL
J/WwEDTG1qs2jCkNWYkFEUwz6fMWzzTUydj665dkQI3SNwRAJ9dE0LgybM6Yws3C
FQdIUyWR2z8QQYqjLTD9XuDe7ewyoslvFssWRiVzpcnkiu8sWgbTuJ/K+ISCgwo4
rC6Vi7Z4WU47SgL7+d9sOMzDPDIif5mOdfW8uG3tgCeDp/8WNz9IbamCuxhggQpa
+k9jaTHAtOV9ypf1PBUCGHazU7E8hc42XoW6XT0yY3sFynw+VPd1IFVXiWAEBu0=
=gQA8
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.12:
- A fix on GPCv2 power domain driver Kconfig which causes a build
failure when CONFIG_PM is not set.
- Pull down PMIC IRQ pin for imx53-qsrb board to prevent spurious
PMIC interrupts from happening.
- Remove board level OPP override for imx6sx-sdb to fix a boot crash
seen on Rev.C boards.
* tag 'imx-fixes-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx: add PM dependency for IMX7_PM_DOMAINS
ARM: dts: imx6sx-sdb: Remove OPP override
ARM: dts: imx53-qsrb: Pulldown PMIC IRQ pin
Signed-off-by: Olof Johansson <olof@lixom.net>
4.12, please pull the following:
- Baruch provides several fixes for the Raspberry Pi (BCM2835) Device
Tree source include file: uart0 pinctrl node names, pin number for
i2c0, uart0 rts/cts pins and invalid uart1 pin, missing numbers for
ethernet aliases
-----BEGIN PGP SIGNATURE-----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=6jUO
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.12/devicetree-fixes' of http://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-based SoC Device Tree fixes for
4.12, please pull the following:
- Baruch provides several fixes for the Raspberry Pi (BCM2835) Device
Tree source include file: uart0 pinctrl node names, pin number for
i2c0, uart0 rts/cts pins and invalid uart1 pin, missing numbers for
ethernet aliases
* tag 'arm-soc/for-4.12/devicetree-fixes' of http://github.com/Broadcom/stblinux:
ARM: dts: bcm2835: add index to the ethernet alias
ARM: dts: bcm2835: fix uart0/uart1 pins
ARM: dts: bcm2835: fix i2c0 pins
ARM: dts: bcm2835: fix uart0 pinctrl node names
Signed-off-by: Olof Johansson <olof@lixom.net>
We use a directory under arch/$ARCH/boot/dts as an include path
that has links outside of the subtree to find dt-bindings from under
include/dt-bindings. That's been working well, but new DT architectures
haven't been adding them by default.
Recently there's been a desire to share some of the DT material between
arm and arm64, which originally caused developers to create symlinks or
relative includes between the subtrees. This isn't ideal -- it breaks
if the DT files aren't stored in the exact same hierarchy as the kernel
tree, and generally it's just icky.
As a somewhat cleaner solution we decided to add a $ARCH/ prefix link
once, and allow DTS files to reference dtsi (and dts) files in other
architectures that way.
Original approach was to create these links under each architecture,
but it lead to the problem of recursive symlinks.
As a remedy, move the include link directories out of the architecture
trees into a common location. At the same time, they can now share one
directory and one dt-bindings/ link as well.
Fixes: 4027494ae6 ('ARM: dts: add arm/arm64 include symlinks')
Reported-by: Russell King <linux@armlinux.org.uk>
Reported-by: Omar Sandoval <osandov@osandov.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: linux-arch <linux-arch@vger.kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZF2pwAAoJEHm+PkMAQRiG9aAIAJJyV6Ux9kaX+glqO3KIs0wm
0K/yqMOv1JTfJ1UUgY4iZbk5XOPPmXv1bdKJFECZfuAHdymJUF/RVNNvDlZbaLdd
K8vDEi92eRwcf07a5b/Q2F8yNfADKKmRAA/oAbuQLBhJ0dPHig70PIvi9gq9kqiE
Ft1MinbsZLavYatLm7oVDr/nsYebEDMGwTy0EX5bF2YjydfAlCvVWnI5ld5wisiV
0fQF4W7MMjjcpAzG8uq3atEB8iQcWS2Ykz2chZRbYzHcdV2WJW751Vge9xc05Hzi
rxlqn6peZFiFyM0qdPLhY0ktGzSTZcCFeb3aZicvm5aOamy2KJjOSZrEwjU8kts=
=VHpx
-----END PGP SIGNATURE-----
Merge tag 'v4.12-rc1' into fixes
We've received a few fixes branches with -rc1 as base, but our contents was
still at pre-rc1. Merge it in expliticly to make 'git merge --log' clear on
hat was actually merged.
Signed-off-by: Olof Johansson <olof@lixom.net>
On imx6sx-sdb rev B/C the VDD_ARM_IN and VDD_SOC_IN supplies are connected
together and both are supplied by the SW1A PMIC output, so model this
correctly in the device tree.
Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Allwinner V3s SoC has a SPI controller, muxed with the MMC2 controller
at PC bank. The controller itself is identical to the one in H3 SoC.
Add device tree node and the only pinmux node for it.
Tested with a Winbond W25Q128FV SPI NOR soldered on the Lichee Pi
early sample.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Lichee Pi Zero board has a "dock board" which needs to be soldered
with the 1.27mm stamp holes on a Lichee Pi Zero board.
It features:
- Onboard MIC and headphone jack (not supported yet)
- Ethernet port (not supported yet)
- An extra MicroSD slot connected to MMC1 controller
- four keys connected to the LRADC.
As it needs to be soldered with the main board to use, add a stand-alone
device tree for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add secondary pinctrl set for UART2 which can be used to prevent conflicts
with sdmmc pins.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Correct UART2 PINCTRL flag to use the correct pull up setting
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Refer to Chapter 5.3.2 of rk3229 TRM, we can see that GPIO1A[2,4,5]
using RK_FUNC_2 not RK_FUNC_1. This patch fixes it.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
On dra7, as per TRM, the HW shutdown (TSHUT) temperature is hardcoded
to 123C and cannot be modified by SW. This means when the temperature
reaches 123C HW asserts TSHUT output which signals a warm reset.
This reset is held until the temperature goes below the TSHUT low (105C).
While in SW, the thermal driver continuously monitors current temperature
and takes decisions based on whether it reached an alert or a critical point.
The intention of setting a SW critical point is to prevent force reset by HW
and instead do an orderly_poweroff(). But if the SW critical temperature is
greater than or equal to that of HW then it defeats the purpose. To address
this and let SW take action before HW does keep the SW critical temperature
less than HW TSHUT value.
The value for SW critical temperature was chosen as 120C just to ensure
we give SW sometime before HW catches up.
Document reference
SPRUI30C – DRA75x, DRA74x Technical Reference Manual - November 2016
SPRUHZ6H - AM572x Technical Reference Manual - November 2016
Tested on:
DRA75x PG 2.0 Rev H EVM
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds a new node to the LEGO MINDSTORMS EV3 device tree for the battery.
Signed-off-by: David Lechner <david@lechnology.com>
[nsekhar@ti.com: minor headline fix]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
sdcard access with the sdhost controller is faster.
Read access (dd with 64k blocks on rpi2):
CONFIG_MMC_SDHCI_IPROC: 11-12 MB/s
CONFIG_MMC_BCM2835: 19-20 MB/s
Differences on write access are pretty much in the noise.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Eric Anholt <eric@anholt.net>
If we have Linux installed in eMMC we can boot without
µSD card, but inserting one is not recognised.
The reason is that the card detect gpio (gpio5_152)
is not configured and attached to the mmc1 interface
driver and the mmc driver does not poll by default.
Hence we add pinmux and gpio setup for the SDCARD_NCD
signal.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Droid 4 has WL 1285C connected to the OMAP's UART4 port, which is
used for Bluetooth and most likely can also be used for controlling
the FM radio and GPS receivers.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
USB1 port is micro-AB type and can function as peripheral
as well as host. Enable dual-role mode for USB1.
We don't want to use the OTG controller block on this
platform as it limits host mode to high-speed. Instead
we rely on extcon framework to give us ID events for
dual-role mode detection.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Compiling the DT file with W=1, DTC warns like follows:
Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property
Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The rv4162 compatbile string is missing the vendor part, add it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix commit 05c4ffc3a2 ("ARM: dts: LogicPD Torpedo: Add MT9P031 Support")
In the previous commit, I indicated that the only testing was done by
showing the camera showed up when probing. This patch fixes an incorrect
pin muxing on cam_d0, cam_d1 and cam_d2.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CEC pin was always pulled up, making it impossible to use it.
Change to PIN_INPUT so it can be used by the new CEC support.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The clock polarity setting of the mcbsp connected to
the modem was wrong so almost only noise
was received.
With this patch it is also the same as it was on
earlier non-dt kernels where it was working properly
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add power hold and power controller properties to palmas node.
This is needed to shutdown pmic correctly on boards with
powerhold set.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As suggested by Eduardo Valentin this adds the thermal zone for
the bcm2835 SoC with its single thermal sensor. We start with
the criticial trip point and leave the cooling devices empty
since we don't have any at the moment. Since the coefficients
could vary depending on the SoC we need to define them separate.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Raspbian and Fedora have decided to support the Pi3 in 32-bit mode for
now, so it's useful to be able to test that mode on an upstream
kernel. It's also been useful for me to use the same board for 32-bit
and 64-bit development.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Olof Johansson <olof@lixom.net>
The Raspberry Pi startup stub files for multi-core BCM283X processors
make the secondary CPUs spin until the corresponding mailbox is
written. These stubs are loaded at physical address 0x00000xxx (as seen
by the ARMs), but this page will be reused by the kernel unless it is
explicitly reserved, causing the waiting cores to execute random code.
Use the /memreserve/ Device Tree directive to mark the first page as
off-limits to the kernel.
See: https://github.com/raspberrypi/linux/issues/1989
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
During my research I found that some of the requirements for the memory
buffers for MFC v6+ devices were blindly copied from the previous (v5)
version and simply turned out to be excessive. The relaxed requirements
are applied by the recent patches to the MFC driver and the driver is
now fully functional even without the reserved memory blocks for all
v6+ variants. This patch removes those reserved memory nodes from all
boards having MFC v6+ hardware block.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
When running a stress playback/stop loop test on a mx6colibri channel
swaps can be noticed randomly.
Increasing the SGTL5000 LRCLK pad strength to its maximum value fixes
the issue, so add the 'lrclk-strength' property to avoid the audio
channel swaps.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When running a stress playback/stop loop test on a mx6wandboard channel
swaps can be noticed randomly.
Increasing the SGTL5000 LRCLK pad strength to its maximum value fixes
the issue, so add the 'lrclk-strength' property to avoid the audio
channel swaps.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add nodes to support the Controller Area Network(M_CAN) on SAMA5D2.
The version of M_CAN IP core is 3.1.0 (CREL = 0x31040730).
As said in SAMA5D2 datasheet, the CAN clock is recommended to use
frequencies of 20, 40 or 80 MHz. To achieve these frequencies,
PMC GCLK3 must select the UPLLCK(480 MHz) as source clock and
divide by 24, 12, or 6. So, the "assigned-clock-rates" property
has three options: 20000000, 40000000, and 80000000.
The "assigned-clock-parents" property should be referred to utmi
fixedly.
The MSBs [bits 31:16] of the CAN Message RAM for CAN0 and CAN1 are
default configured in 0x00200000. To avoid conflict with SRAM map
for PM, change them to 0x00210000 in the AT91Bootstrap via setting
the CAN Memories Address-based Register(SFR_CAN) of SFR.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The aa104xd12 and aa121td01 panels are LVDS panels, not DPI panels.
Use the correct DT bindings.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The dock board of Lichee Pi Zero features a MicroSD slot on MMC1, which
can be used with a MicroSD card or the MicroSD-slot Wi-Fi card provided
by Lichee Pi Zero.
Add pinmux for the mmc1 controller, and specify it in the mmc1 device
node as it's the only pinmux for mmc1.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner V3s features a LRADC like the ones in older SoCs.
Add a device tree node for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
All the used CCU definitions are stripped from the V3s DTSI file when
it's merged, as the DTSI file and the CCU device tree binding headers
went to different trees.
As they're all in Linus's tree now, restore the usage of the
definitions.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add Sean as one of the authors for the mt7623.dtsi
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add afe nodes to the mt7623.dtsi file. Which
is the necessary node for I2S audio in/out.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add crypto engine nodes to the mt7623.dtsi file.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add USB nodes to the mt7623.dtsi file.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add e/MMC nodes to the mt7623.dtsi file.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add NAND/EEC nodes to the mt7623.dtsi file.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add spi controller nodes to the mt7623.dtsi file
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add I2C nodes to the mt7623.dtsi file.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add PMIC wrapper node to the mt7623.dtsi file which
is necessary for the control of PMIC from Mediatek.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add pin controller node to the mt7623.dtsi file
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add power domain controller node (scpsys) for MT7623.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add MT7623 subsystem clock controllers for hifsys and ethsys.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add clock controller nodes for MT7623, including topckgen, infracfg,
pericfg and apmixedsys. This patch also cleans up two oscillators that
provide clocks for MT7623. Switch the uart clocks to the real ones while
at it.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add the "1v8" pinctrl state and sd-uhs-sdr50 property to SDHI{0,1,2}.
And the sd-uhs-sdr104 property to SDHI0.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Define the upper limit otherwise the driver cannot utilize max speeds.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Add node for the GyroADC block and it's associated clock.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This adds the USB0 and USB1 clocks to the device tree.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The device trees for Renesas SoCs use either pfc or pin-controller as the
node name for the PFC device. This patch is intended to take a step towards
unifying the node name used as pin-controller which appears to be the more
generic of the two and thus more in keeping with the DT specs.
My analysis is that this is a user-visible change to the extent that kernel
logs, and sysfs entries change from e6050000.pfc and pfc@e6050000 to
e6050000.pin-controller and pin-controller@e6050000.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
The device trees for Renesas SoCs use either pfc or pin-controller as the
node name for the PFC device. This patch is intended to take a step towards
unifying the node name used as pin-controller which appears to be the more
generic of the two and thus more in keeping with the DT specs.
My analysis is that this is a user-visible change to the extent that kernel
logs, and sysfs entries change from e6060000.pfc and pfc@e6060000 to
e6060000.pin-controller and pin-controller@e6060000.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
The device trees for Renesas SoCs use either pfc or pin-controller as the
node name for the PFC device. This patch is intended to take a step towards
unifying the node name used as pin-controller which appears to be the more
generic of the two and thus more in keeping with the DT specs.
My analysis is that this is a user-visible change to the extent that kernel
logs, and sysfs entries change from e6060000.pfc and pfc@e6060000 to
e6060000.pin-controller and pin-controller@e6060000.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
The device trees for Renesas SoCs use either pfc or pin-controller as the
node name for the PFC device. This patch is intended to take a step towards
unifying the node name used as pin-controller which appears to be the more
generic of the two and thus more in keeping with the DT specs.
My analysis is that this is a user-visible change to the extent that kernel
logs, and sysfs entries change from e6060000.pfc and pfc@e6060000 to
e6060000.pin-controller and pin-controller@e6060000.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
The device trees for Renesas SoCs use either pfc or pin-controller as the
node name for the PFC device. This patch is intended to take a step towards
unifying the node name used as pin-controller which appears to be the more
generic of the two and thus more in keeping with the DT specs.
My analysis is that this is a user-visible change to the extent that kernel
logs, and sysfs entries change from fffc0000.pfc and pfc@fffc0000 to
fffc0000.pin-controller and pin-controller@fffc0000.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
The device trees for Renesas SoCs use either pfc or pin-controller as the
node name for the PFC device. This patch is intended to take a step towards
unifying the node name used as pin-controller which appears to be the more
generic of the two and thus more in keeping with the DT specs.
My analysis is that this is a user-visible change to the extent that kernel
logs, and sysfs entries change from fffc0000.pfc and pfc@fffc0000 to
fffc0000.pin-controller and pin-controller@fffc0000.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
The device trees for Renesas SoCs use either pfc or pin-controller as the
node name for the PFC device. This patch is intended to take a step towards
unifying the node name used as pin-controller which appears to be the more
generic of the two and thus more in keeping with the DT specs.
My analysis is that this is a user-visible change to the extent that kernel
logs, and sysfs entries change from e6050000.pfc and pfc@e6050000 to
e6050000.pin-controller and pin-controller@e6050000.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
The device trees for Renesas SoCs use either pfc or pin-controller as the
node name for the PFC device. This patch is intended to take a step towards
unifying the node name used as pin-controller which appears to be the more
generic of the two and thus more in keeping with the DT specs.
My analysis is that this is a user-visible change to the extent that kernel
logs, and sysfs entries change from e6050000.pfc and pfc@e6050000 to
e6050000.pin-controller and pin-controller@e6050000.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
The device trees for Renesas SoCs use either pfc or pin-controller as the
node name for the PFC device. This patch is intended to take a step towards
unifying the node name used as pin-controller which appears to be the more
generic of the two and thus more in keeping with the DT specs.
My analysis is that this is a user-visible change to the extent that kernel
logs, and sysfs entries change from e0140200.pfc and pfc@e0140200 to
e0140200.pin-controller and pin-controller@e0140200.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
The USDHC instances need the USDHC NAND and IPG clock in order to
operate. Reference them properly by replacing the dummy clocks with
the actual clocks.
Note that both clocks are currently implicitly enabled since they
are part of the i.MX 7 clock drivers init_on list. This might
change in the future.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The rv4162 compatbile string is missing the vendor part, add it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The rv4162 vendor is microcrystal, not ST.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The rv4162 vendor is microcrystal, not ST.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the more specific QuadPlus compatible to the GPC node, to trigger the
required workarounds in the power domain code.
In regard to the interrupt mapping the QuadPlus controller is fully
compatible to the Quad one, so keep that compatible in place.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adopt the i.MX6Q/DL DT to the new and more flexible GPC binding.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove the sky2 ethernet device node from the pcie controller which was
invalid to begin with.
The original intent was to allow the bootloader to populate the MAC via
dt but this requires the PCI bus topology to be complete in dt as well
and as these boards have an expansion connector that topology is dynamic
and can't be represented here.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The board file for imx6sx-sdb overrides cpufreq operating points to use
higher voltages. This is done because the board has a shared rail for
VDD_ARM_IN and VDD_SOC_IN and when using LDO bypass the shared voltage
needs to be a value suitable for both ARM and SOC.
This only applies to LDO bypass mode, a feature not present in upstream.
When LDOs are enabled the effect is to use higher voltages than necessary
for no good reason.
Setting these higher voltages can make some boards fail to boot with ugly
semi-random crashes reminiscent of memory corruption. These failures only
happen on board rev. C, rev. B is reported to still work.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Fixes: 54183bd7f7 ("ARM: imx6sx-sdb: add revb board and make it default")
Cc: stable@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently the following errors are seen:
[ 14.015056] mc13xxx 0-0008: Failed to read IRQ status: -6
[ 27.321093] mc13xxx 0-0008: Failed to read IRQ status: -6
[ 27.411681] mc13xxx 0-0008: Failed to read IRQ status: -6
[ 27.456281] mc13xxx 0-0008: Failed to read IRQ status: -6
[ 30.527106] mc13xxx 0-0008: Failed to read IRQ status: -6
[ 36.596900] mc13xxx 0-0008: Failed to read IRQ status: -6
Also when reading the interrupts via 'cat /proc/interrupts' the
PMIC GPIO interrupt counter does not stop increasing.
The reason for the storm of interrupts is that the PUS field of
register IOMUXC_SW_PAD_CTL_PAD_CSI0_DAT5 is currently configured as:
10 : 100k pullup
and the PMIC interrupt is being registered as IRQ_TYPE_LEVEL_HIGH type,
which is the correct type as per the MC34708 datasheet.
Use the default power on value for the IOMUX, which sets PUS field as:
00: 360k pull down
This prevents the spurious PMIC interrupts from happening.
Commit e1ffceb078 ("ARM: imx53: qsrb: fix PMIC interrupt level")
correctly described the irq type as IRQ_TYPE_LEVEL_HIGH, but
missed to update the IOMUX of the PMIC GPIO as pull down.
Fixes: e1ffceb078 ("ARM: imx53: qsrb: fix PMIC interrupt level")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Rockchip finally named the SOC as RV1108, so change it
for compatible.
The rk1108/rv1108 is completely new to the market, so there no real
devices exist in the wild, only the Rockchip internal evaluation
board. Therefore we're not breaking any existing devices when
changing compatible values.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
[added paragraph about no real devices existing]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Rockchip finally named the SOC as RV1108, so change it
for compatible.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
[adapt include in rk1108-evb.dts to not introduce errors]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The R_CCU of H3/H5 currently wrongly used A64 R_CCU compatible.
Fix it by changing it to the correct H3 compatible.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This names the GPIO lines on the Banana Pi board in accordance with
the A20_Banana_Pi v1.4 Specification.
This will make these line names reflect through to user space
so that they can easily be identified and used with the new
character device ABI.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Orange Pi 2 routes the LINEOUT pins through a SGM8900 PA which
needs to be enabled. The onboard microphone is routed to MIC1, with
MBIAS providing power.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
We should use hyphens and not underscores in device node names.
Replace the ones that were just added.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Kbuild now complains about leading zeroes in the address portion of
device node names.
Get rid of them all, except for the uart device node. U-boot currently
hard codes the device node path. We can remove the leading zero for
the uart once we teach U-boot to use the aliases or stdout-path
property.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
tcon0 contains a muxing register used to mux tcon output to downstream
hdmi or mipi dsi encoders. tcon0 must be available for the mux to be
configured.
Whether the display subsystem is enabled or not is now solely controlled
by the display-engine node.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner A31/A31s SoCs have 2 display pipelines, as in 2 display
frontends, backends, and tcons each. The relationship between the
backends and tcons are 1:1, but the frontends can feed either backend.
Add device nodes and of graph nodes describing this relationship.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The NextThing Co. CHIP has an AXP209 PMIC with battery connector.
This enables the battery power supply subnode.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Sinlinx SinA33 has an AXP223 PMIC and a battery connector, thus, we
enable the battery power supply subnode in its Device Tree.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The X-Powers AXP22X PMIC exposes battery supply various data such as
the battery status (charging, discharging, full, dead), current max
limit, current current, battery capacity (in percentage), voltage max
limit, current voltage, and battery capacity (in Ah).
This adds the battery power supply subnode for AXP22X PMIC.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The X-Powers AXP209 PMIC exposes battery supply various data such as
the battery status (charging, discharging, full, dead), current max
limit, current current, battery capacity (in percentage), voltage max
and min limits, current voltage, and battery capacity (in Ah).
This adds the battery power supply subnode for AXP20X PMIC.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Compiling the DT file with W=1, DTC warns like follows:
Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property
Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Bananapi M2 Plus has a USB OTG port that can be used in both
powered host mode and peripheral mode. When in peripheral mode,
the port does not power the board. There is no VBUS sensing on
the port.
This patch adds the regulator controlling VBUS on the OTG port,
the GPIO for the ID detect pin, and enables the USB OTG and host
controllers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Orange Pi PC, PC Plus, and Plus 2E all have a USB OTG port
that can be used in both powered host mode and peripheral mode.
When in peripheral mode, the port does not power the board.
There is no VBUS sensing on the port. All three boards have all
related pins routed the same way.
The device tree file for the Orange Pi Plus 2E is based on the
Orange Pi PC Plus, which itself is based on the Orange Pi PC.
Changes to the base Orange Pi PC device tree file affects all 3
boards.
This patch adds the regulator controlling VBUS on the OTG port,
the GPIO for the ID detect pin, and enables the USB OTG and host
controllers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As part of our effort to move pinctrl/GPIO interlocking into the
driver where it belongs, this patch drops the definition and usage
of the mmc0_cd_pin_reference_design pinmux setting for the default
mmc0 card detect GPIO pin.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As part of our effort to move pinctrl/GPIO interlocking into the
driver where it belongs, this patch drops the definition and usage
of the pinmux settings for the common regulators defined in
sunxi-common-regulators.dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The pinmux setting nodes all have an address element in their node
names, however the pinctrl node does not have #address-cells.
Rename the existing pinmux setting nodes and labels in sun8i-a83t.dtsi,
dropping identifiers for functions that only have one possible setting,
and using the pingroup name if the function is identically available on
different pingroups.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
skeleton.dtsi is deprecated. Remove it from sun8i-a83t.dtsi and add
the needed device nodes directly.
Also drop an extra, non-style-conforming line in the copyright license
header.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This pull request brings back bcm2835 DT fixups from Baruch Siach that
got misplaced after a PR for 4.11 got rejected.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Now that the rockchip usb phy has a vbus-supply property use that to
control the vbus regulator on rock2.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
to me not catching up as quickly on patch review than anything else.
Overall it seems normal though, a few small changes to the core, mostly
small non-critical fixes here and there as well as driver updates for new
and existing hardware support. The biggest things are the TI clk driver
rework to lay the groundwork for clkctrl support in the next merge window
and the AmLogic audio/graphics clk support.
Core:
* clk_possible_parents debugfs file so we know which parents a clk
could possibly have
* Fix to make clk rate change notifiers stop on the first failure instead
of continuing
New Drivers:
* Mediatek MT6797 SoCs
* hi655x PMIC clks
* AmLogic Meson SoC i2s and spdif audio clks and Mali graphics clks
* Allwinner H5 SoCs and PRCM hardware
Updates:
* Nvidia Tegra T210 cleanups and non-critical fixes
* TI OMAP cleanups in preparation for clkctrl support
* Trivial fixes like kcalloc(), devm_* conversions, and seq_puts()
* ZTE zx296718 SoC VGA clks
* Rockchip clk-ids, fixups, and rename of rk1108 to rv1108
* Support for IDT VersaClock 5P49V5935
* Renesas R-Car H3 and M3-W IMR clks and ES2.0 rev of R-Car H3 support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJZE0YJAAoJEK0CiJfG5JUl9tEQAKVJx8VztYGt1REoFMtEEHmO
azhxT/uYGgdOMAr9a3mQxqfm5cJbjnb1EZj2RfC1XHs31BF66j40y9+5d8hY8Hzu
5IkY86s77TlqxGLwQcAsU75Q9cFrEW9X0KJ6OSzlrcc5hKlAEk/Z5lBKoQAm3mlU
JqD4DSyFqP0X3YSxV5R7yfarb/X3ekCiQ13EDrPRRhyvHUi6ReUJDDgbPHtA+O2c
ftLAARmxjzitzyvdXokXudkfNm8F5KePK+QkVikf6D/q+kx1D0BNJwZIjhpoiksn
z6LImLQ8l91AWghmqqpOFXolxQncPU+bJIL9Pox76p5b3EzbQuthIafiso8KsDST
4g3mHm42Yfx9uoF+U+pR8IeZfj5yQT91bvf8naPz/ngWMAlLP1IKJUvJN6jeTiwe
cO6GIec1OH40Xl7v/9EafMwDcnFG0cwQmzr/M6wi1dUlmbSygP9NOMTHlr6W/0wa
K2hCD6b5UHEgHmdfiJbZ2tKxLO0e8LABW+AU8fQH5S2eNe14vY0GvCzfAq5MArIz
QRpso/kdtGpTpwMEvV6PUmJ0IxYEjtNJVjGJYbORwios0SK0Xl6bJWf7gwn5crB6
nua9tVZtJEOHJS7S+ESp3VvuXj2/UGPoRRf5OsERo1S6ydGUQH+wDi1SJMdo/vtX
bIPzIw6WPxMp24JyKOhh
=/5a/
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"Sort of on the quieter side this time, which is probably due more to
me not catching up as quickly on patch review than anything else.
Overall it seems normal though, a few small changes to the core,
mostly small non-critical fixes here and there as well as driver
updates for new and existing hardware support.
The biggest things are the TI clk driver rework to lay the groundwork
for clkctrl support in the next merge window and the AmLogic
audio/graphics clk support.
Core:
- clk_possible_parents debugfs file so we know which parents a clk
could possibly have
- Fix to make clk rate change notifiers stop on the first failure
instead of continuing
New Drivers:
- Mediatek MT6797 SoCs
- hi655x PMIC clks
- AmLogic Meson SoC i2s and spdif audio clks and Mali graphics clks
- Allwinner H5 SoCs and PRCM hardware
Updates:
- Nvidia Tegra T210 cleanups and non-critical fixes
- TI OMAP cleanups in preparation for clkctrl support
- trivial fixes like kcalloc(), devm_* conversions, and seq_puts()
- ZTE zx296718 SoC VGA clks
- Rockchip clk-ids, fixups, and rename of rk1108 to rv1108
- IDT VersaClock 5P49V5935 support
- Renesas R-Car H3 and M3-W IMR clks and ES2.0 rev of R-Car H3
support"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (151 commits)
clk: x86: pmc-atom: Checking for IS_ERR() instead of NULL
clk: ti: divider: try to fix ti_clk_register_divider
clk: mvebu: Use kcalloc() in two functions
clk: mvebu: Use kcalloc() in of_cpu_clk_setup()
clk: nomadik: Delete error messages for a failed memory allocation in two functions
clk: nomadik: Use seq_puts() in nomadik_src_clk_show()
clk: Improve a size determination in two functions
clk: Replace four seq_printf() calls by seq_putc()
clk: si5351: Delete an error message for a failed memory allocation in si5351_i2c_probe()
clk: si5351: Use devm_kcalloc() in si5351_i2c_probe()
clk: at91: Use kcalloc() in of_at91_clk_pll_get_characteristics()
reset: mediatek: Add MT2701 ethsys reset controller include file
clk: mediatek: add mt2701 ethernet reset
clk: hi6220: Add the hi655x's pmic clock
clk: ti: fix building without legacy omap3
clk: ti: fix linker error with !SOC_OMAP4
clk: hi3620: Fix a typo in one variable name
clk: hi3620: Delete error messages for a failed memory allocation in two functions
clk: hi3620: Use kcalloc() in hi3620_mmc_clk_init()
clk: hisilicon: Delete error messages for failed memory allocations in hisi_clk_init()
...
- mt8173: fix mmc parameters
- set timer frequency explicitly and force the driver to set it
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJZEfOYAAoJELQ5Ylss8dNDizsP/2/tAoJ66wxdiO3Jd4Wgq+Kb
eFwwre2WxcBjuJyzzIxIgnDib0TKgKSjo5qcakSjmp4RNg18Mt1DRP+ty6eJ5Yh8
2c+xtj31lcfCrpi1N6hKqqoW8yYfgrHuQxsrlS4wrUs9YcDcDk6dWAoJ5tUJepE+
TrgZ5zqUiseTW26ULFvUlXDg/qf1rBQPVMeOiV/fmGnyjPvTL5simmLnyR/DZjXO
gCccVvqDs1XnzBT0cYDovL+HeayQ7fLRrhpoPiyLFycr5ESSIDYvTnfuFd8Vz5qR
5bM5WVmOfXJ93n0qrWoN+ILQXir3a8Lk9j+9Nx4YuMS0V4CwHFkYZT3WFCFuN76p
RwHNI28LQug9d9EDKfX0TgqyHvlE+VLGjIv0lYlH5gEGp0qX2QAwU+g+nhhHiugB
GTNv6BwRtceMx7iILsEUnEShYwN5JZmFHeCQyjqGLhVT2Hb2kwudRzA157ObaZNV
NLb48+M4qRH9seOM/bp7iARDgS+L9mevJ7IF7OMCdogWDn0Cq+9MvclLR8c8u7Ml
M5Nuuto8v2yoXzT7LEp5o4Q8ZxzE4rPsXBsgDu5NQYr5lQFcWskvG3yZJyo5HRA4
OW1ERkRhOcKRQm9bYTVtZZ2au3TJM6P0UBgvY6hFwwRmgHX5MkDBULj8a/vmK2gc
0EvcriDgNEdOgoETO4+y
=yOfu
-----END PGP SIGNATURE-----
Merge tag 'v4.11-next-fixes' of https://github.com/mbgg/linux-mediatek into fixes
Pull "DTS fixes" from Matthias Brugger:
- mt8173: fix mmc parameters
- set timer frequency explicitly and force the driver to set it
* tag 'v4.11-next-fixes' of https://github.com/mbgg/linux-mediatek:
ARM64: dts: mediatek: configure some fixed mmc parameters
arm: dts: mt7623: add clock-frequency to the a7 timer node to mt7623.dtsi
Device-tree updates for arm64 platforms. Just as with 32-bit, a bunch of smaller
changes, but also some new platforms that are worth mentioning:
* Rockchip RK3399 platforms for Chromebooks, including Samsung Chromebook
Plus (Kevin)
* Orange Pi PC2 (Allwinner H5)
* Freescale LS2088A and LS1088A SoCs
* Expanded support for Nvidia Tegra186 (and Jetson TX2)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJZEA5TAAoJEIwa5zzehBx3uPwP/3NBPKvsDQha/x+PPgtSM1cM
pUEF1fxsLftrt+pUeRgMZqGE2xu5vVUKEQsr7KDdWMS9LMs50Pp9dTvfxr7A4Asm
WRRMR7Y3gPbr49uf4+JLLmn0hYXTeaoUftVneBj0qU9Flwe3mQDVULiRjPalWYVB
g0+NwkPE2lrqrudceA2HiVEXqNlVXCIh2mdMaC7Luo0VEsz7nRHT0TOGPaxnXB3M
NoJ56FPHtv3x9+C56B5CLJ/+Ya8SLgfqVwwoK8FgoqDzEF3nbhf/WCUyph+gHdP3
D+jMk7t0tvIW8Ne4TGXenoxBznZxgh5ObpLlKBKPCGJkKxpfuq9koH33MmY/WoUN
7uh3F3HI2sGr7tY/xaN8H7a9A4mHzipj8nqaAsjAJppIpioecGCFVtkY5q0jfxLC
aAc1o4zoimdPs9q9mu/qhgKNxWkoTYnwvtWHuwqEOggvSb1ulS1SPS24VkKrc4LI
XMGbA4mQOuFwZyG4FVfvWzbnhsHzDh4cgHaVGra6z5zoX1MUrvieCWEji+Ul1VWa
lUJ2sTilvSGkwjGcMUSki5p9GcU8dPXwqKiZqDuGx6Ps4aQsw0vz286BnBeVsusG
qLRH4nkqbF9xCEz9h71mcU6WMu17EsG9zMoCg5K4EZ+RIG3cgWq0dMWW1LqtRn7S
2YqayY3+UEyMPN146R1V
=q3Ix
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Olof Johansson:
"Device-tree updates for arm64 platforms. Just as with 32-bit, a bunch
of smaller changes, but also some new platforms that are worth
mentioning:
- Rockchip RK3399 platforms for Chromebooks, including Samsung
Chromebook Plus (Kevin)
- Orange Pi PC2 (Allwinner H5)
- Freescale LS2088A and LS1088A SoCs
- Expanded support for Nvidia Tegra186 (and Jetson TX2)"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (180 commits)
arm64: dts: Add basic DT to support Spreadtrum's SP9860G
arm64: dts: exynos: Use - instead of @ for DT OPP entries
arm64: dts: exynos: Add support for s6e3hf2 panel device on TM2e board
arm64: dts: juno: add information about L1 and L2 caches
arm64: dts: juno: fix few unit address format warnings
arm64: marvell: dts: enable the crypto engine on the Armada 8040 DB
arm64: marvell: dts: enable the crypto engine on the Armada 7040 DB
arm64: marvell: dts: add crypto engine description for 7k/8k
arm64: dts: marvell: add sdhci support for Armada 7K/8K
arm64: dts: marvell: add eMMC support for Armada 37xx
arm64: dts: hisi: add pinctrl dtsi file for HiKey960 development board
arm64: dts: hisi: add drive strength levels of the pins for Hi3660 SoC
arm64: dts: hisi: enable the NIC and SAS for the hip07-d05 board
arm64: dts: hisi: add SAS nodes for the hip07 SoC
arm64: dts: hisi: add RoCE nodes for the hip07 SoC
arm64: dts: hisi: add network related nodes for the hip07 SoC
arm64: dts: hisi: add mbigen nodes for the hip07 SoC
arm64: dts: rockchip: fix the memory size of PX5 Evaluation board
arm64: dts: hisilicon: add dts files for hi3798cv200-poplar board
dt-bindings: arm: hisilicon: add bindings for hi3798cv200 SoC and Poplar board
...
Device-tree continues to see lots of updates. The majority of patches
here are smaller changes for new hardware on existing platforms, and
there are a few larger changes worth pointing out.
Major new platforms:
- Gemini has been ported to DT, so a handful of "new" platforms moved over
from board files
- Rockchip RK3288 support for Tinkerboard and Phytec phyCORE-RK3288 SoM and RDK
- A bunch of embedded platforms, several Linksys platforms, Synology DS116,
- Motorola Droid4 (really old OMAP-based phone) support is added.
Some refactorings, i.e. Allwinner H3/H5 support is commonalized.
And lots of smaller changes, cleanups, etc. See shortlog for more description
We're adding ability to cross-include DT files between arm and arm64,
by creating appropriate links in the dt-include directory, and using arm/
and arm64/ as include prefixes. This will avoid other local hacks such as
per-file links between the two arch trees (this broke for external mirroring
of DT contents). Now they can just provide their own appropriate dt-include
hierarcy per platform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=v6w6
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM Device-tree updates from Olof Johansson:
"Device-tree continues to see lots of updates. The majority of patches
here are smaller changes for new hardware on existing platforms, and
there are a few larger changes worth pointing out.
Major new platforms:
- Gemini has been ported to DT, so a handful of "new" platforms moved
over from board files
- Rockchip RK3288 support for Tinkerboard and Phytec phyCORE-RK3288
SoM and RDK
- A bunch of embedded platforms, several Linksys platforms, Synology
DS116,
- Motorola Droid4 (really old OMAP-based phone) support is added.
Some refactorings, i.e. Allwinner H3/H5 support is commonalized.
And lots of smaller changes, cleanups, etc. See shortlog for more
description
We're adding ability to cross-include DT files between arm and arm64,
by creating appropriate links in the dt-include directory, and using
arm/ and arm64/ as include prefixes. This will avoid other local hacks
such as per-file links between the two arch trees (this broke for
external mirroring of DT contents). Now they can just provide their
own appropriate dt-include hierarcy per platform"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (349 commits)
ARM: dts: exynos: Use - instead of @ for DT OPP entries
arm: spear6xx: add DT description of the ADC on SPEAr600
arm: spear6xx: remove unneeded pinctrl properties in spear600-evb
arm: spear6xx: switch spear600-evb to the new flash partition DT binding
arm: spear6xx: fix spaces in spear600-evb.dts
arm: spear6xx: use node labels in spear600-evb.dts
arm: spear6xx: add labels to various nodes in spear600.dtsi
ARM: dts: vexpress: fix few unit address format warnings
ARM: dts: at91: sama5d3_xplained: not all ADC channels are available
ARM: dts: at91: sama5d3_xplained: fix ADC vref
ARM: dts: at91: add envelope detector mux to the Axentia TSE-850
ARM: dts: armada-38x: label USB and SATA nodes
ARM: dts: imx6q-utilite-pro: add hpd gpio
ARM: dts: imx6qp-sabresd: Set reg_arm regulator supply
ARM: dts: imx6qdl-sabresd: Set LDO regulator supply
ARM: dts: imx: add Gateworks Ventana GW5903 support
ARM: dts: i.MX25: add AIPS control registers
ARM: dts: imx7-colibri: add Carrier Board 3.3V/5V regulators
ARM: dts: imx7-colibri: remove 1.8V fixed regulator
ARM: dts: imx7-colibri: allow to disable Ethernet rail
...
We need to tell the driver what the timers frequency is and that the core
has not be configured by the bootrom. Not doing so makes the unit not
boot.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Pull ARM updates from Russell King:
"Lots of little things this time:
- allow modules to be autoloaded according to the HWCAP feature bits
(used primarily for crypto modules)
- split module core and init PLT sections, since the core code and
init code could be placed far apart, and the PLT sections need to
be local to the code block.
- three patches from Chris Brandt to allow Cortex-A9 L2 cache
optimisations to be disabled where a SoC didn't wire up the out of
band signals.
- NoMMU compliance fixes, avoiding corruption of vector table which
is not being used at this point, and avoiding possible register
state corruption when switching mode.
- fixmap memory attribute compliance update.
- remove unnecessary locking from update_sections_early()
- ftrace fix for DEBUG_RODATA with !FRAME_POINTER"
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8672/1: mm: remove tasklist locking from update_sections_early()
ARM: 8671/1: V7M: Preserve registers across switch from Thread to Handler mode
ARM: 8670/1: V7M: Do not corrupt vector table around v7m_invalidate_l1 call
ARM: 8668/1: ftrace: Fix dynamic ftrace with DEBUG_RODATA and !FRAME_POINTER
ARM: 8667/3: Fix memory attribute inconsistencies when using fixmap
ARM: 8663/1: wire up HWCAP/HWCAP2 feature bits to the CPU modalias
ARM: 8666/1: mm: dump: Add domain to output
ARM: 8662/1: module: split core and init PLT sections
ARM: 8661/1: dts: r7s72100: add l2 cache
ARM: 8660/1: shmobile: r7s72100: Enable L2 cache
ARM: 8659/1: l2c: allow CA9 optimizations to be disabled
-----BEGIN PGP SIGNATURE-----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=Snzj
-----END PGP SIGNATURE-----
Merge tag 'media/v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"Media updates for v4.12-rc1:
- new driver to support mediatek jpeg in hardware codec
- rc-lirc, s5p-cec and st-cec staging drivers got promoted
- hardware histogram support for vsp1 driver
- added Virtual Media Controller driver, to make easier to test the
media controller
- added a new CEC driver (rainshadow-cec)
- removed two staging LIRC drivers for obscure hardware that are too
obsolete
- added support for Intel SR300 Depth camera
- some improvements at CEC and RC core
- lots of driver cleanups, improvements all over the tree
With this series, we're finally getting rid of the LIRC staging
driver. There's just one left (lirc_zilog), with require more care,
as part of its functionality (IR RX) is already provided by another
driver. Work in progress to convert it on the proper way"
* tag 'media/v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (304 commits)
[media] ov2640: print error if devm_*_optional*() fails
[media] atmel-isc: Fix the static checker warning
[media] ov2640: add support for MEDIA_BUS_FMT_YVYU8_2X8 and MEDIA_BUS_FMT_VYUY8_2X8
[media] ov2640: fix vflip control
[media] ov2640: fix duplicate width+height returning from ov2640_select_win()
[media] ov2640: add missing write to size change preamble
[media] ov2640: add information about DSP register 0xc7
[media] ov2640: improve banding filter register definitions/documentation
[media] ov2640: fix init sequence alignment
[media] ov2640: make GPIOLIB an optional dependency
[media] xc5000: fix spelling mistake: "calibration"
[media] vidioc-queryctrl.rst: fix menu/int menu references
[media] media-entity: only call dev_dbg_obj if mdev is not NULL
[media] pixfmt-meta-vsp1-hgo.rst: remove spurious '-'
[media] mtk-vcodec: avoid warnings because of empty macros
[media] coda: bump maximum number of internal framebuffers to 17
[media] media: mtk-vcodec: remove informative log
[media] subdev-formats.rst: remove spurious '-'
[media] dw2102: limit messages to buffer size
[media] ttusb2: limit messages to buffer size
...
Core changes:
- Add bi-directional and output-enable pin configurations to
the generic bindings and generic pin controlling core.
New drivers or subdrivers:
- Armada 37xx SoC pin controller and GPIO support.
- Axis ARTPEC-6 SoC pin controller support.
- AllWinner A64 R_PIO controller support, and opening up the
AllWinner sunxi driver for ARM64 use.
- Rockchip RK3328 support.
- Renesas R-Car H3 ES2.0 support.
- STM32F469 support in the STM32 driver.
- Aspeed G4 and G5 pin controller support.
Improvements:
- A whole slew of realtime improvements to drivers implementing
irqchips: BCM, AMD, SiRF, sunxi, rockchip.
- Switch meson driver to get the GPIO ranges from the device
tree.
- Input schmitt trigger support on the Rockchip driver.
- Enable the sunxi (AllWinner) driver to also be used on ARM64
silicon.
- Name the Qualcomm QDF2xxx GPIO lines.
- Support GMMR GPIO regions on the Intel Cherryview. This
fixes a serialization problem on these platforms.
- Pad retention support for the Samsung Exynos 5433.
- Handle suspend-to-ram in the AT91-pio4 driver.
- Pin configuration support in the Aspeed driver.
Cleanups:
- The final name of Rockchip RK1108 was RV1108 so rename the
driver and variables to stay consistent.
-----BEGIN PGP SIGNATURE-----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=BCaA
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.12 cycle.
The extra week before the merge window actually resulted in some of
the type of fixes that usually arrive after the merge window already
starting to trickle in from eager developers using -next, I'm
impressed.
I have recruited a Samsung subsubsystem maintainer (Krzysztof) to deal
with the onset of Samsung patches. It works great.
Apart from that it is a boring round, just incremental updates and
fixes all over the place, no serious core changes or anything exciting
like that. The most pleasing to see is Julia Cartwrights work to audit
the irqchip-providing drivers for realtime locking compliance. It's
one of those "I should really get around to looking into that" things
that have been on my TODO list since forever.
Summary:
Core changes:
- add bi-directional and output-enable pin configurations to the
generic bindings and generic pin controlling core.
New drivers or subdrivers:
- Armada 37xx SoC pin controller and GPIO support.
- Axis ARTPEC-6 SoC pin controller support.
- AllWinner A64 R_PIO controller support, and opening up the
AllWinner sunxi driver for ARM64 use.
- Rockchip RK3328 support.
- Renesas R-Car H3 ES2.0 support.
- STM32F469 support in the STM32 driver.
- Aspeed G4 and G5 pin controller support.
Improvements:
- a whole slew of realtime improvements to drivers implementing
irqchips: BCM, AMD, SiRF, sunxi, rockchip.
- switch meson driver to get the GPIO ranges from the device tree.
- input schmitt trigger support on the Rockchip driver.
- enable the sunxi (AllWinner) driver to also be used on ARM64
silicon.
- name the Qualcomm QDF2xxx GPIO lines.
- support GMMR GPIO regions on the Intel Cherryview. This fixes a
serialization problem on these platforms.
- pad retention support for the Samsung Exynos 5433.
- handle suspend-to-ram in the AT91-pio4 driver.
- pin configuration support in the Aspeed driver.
Cleanups:
- the final name of Rockchip RK1108 was RV1108 so rename the driver
and variables to stay consistent"
* tag 'pinctrl-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (80 commits)
pinctrl: mediatek: Add missing pinctrl bindings for mt7623
pinctrl: artpec6: Fix return value check in artpec6_pmx_probe()
pinctrl: artpec6: Remove .owner field for driver
pinctrl: tegra: xusb: Silence sparse warnings
ARM: at91/at91-pinctrl documentation: fix spelling mistake: "contoller" -> "controller"
pinctrl: make artpec6 explicitly non-modular
pinctrl: aspeed: g5: Add pinconf support
pinctrl: aspeed: g4: Add pinconf support
pinctrl: aspeed: Add core pinconf support
pinctrl: aspeed: Document pinconf in devicetree bindings
pinctrl: Add st,stm32f469-pinctrl compatible to stm32-pinctrl
pinctrl: stm32: Add STM32F469 MCU support
Documentation: dt: Remove ngpios from stm32-pinctrl binding
pinctrl: stm32: replace device_initcall() with arch_initcall()
pinctrl: stm32: add possibility to use gpio-ranges to declare bank range
pinctrl: armada-37xx: Add gpio support
pinctrl: armada-37xx: Add pin controller support for Armada 37xx
pinctrl: dt-bindings: Add documentation for Armada 37xx pin controllers
pinctrl: core: Make pinctrl_init_controller() static
pinctrl: generic: Add bi-directional and output-enable
...
Pull networking updates from David Millar:
"Here are some highlights from the 2065 networking commits that
happened this development cycle:
1) XDP support for IXGBE (John Fastabend) and thunderx (Sunil Kowuri)
2) Add a generic XDP driver, so that anyone can test XDP even if they
lack a networking device whose driver has explicit XDP support
(me).
3) Sparc64 now has an eBPF JIT too (me)
4) Add a BPF program testing framework via BPF_PROG_TEST_RUN (Alexei
Starovoitov)
5) Make netfitler network namespace teardown less expensive (Florian
Westphal)
6) Add symmetric hashing support to nft_hash (Laura Garcia Liebana)
7) Implement NAPI and GRO in netvsc driver (Stephen Hemminger)
8) Support TC flower offload statistics in mlxsw (Arkadi Sharshevsky)
9) Multiqueue support in stmmac driver (Joao Pinto)
10) Remove TCP timewait recycling, it never really could possibly work
well in the real world and timestamp randomization really zaps any
hint of usability this feature had (Soheil Hassas Yeganeh)
11) Support level3 vs level4 ECMP route hashing in ipv4 (Nikolay
Aleksandrov)
12) Add socket busy poll support to epoll (Sridhar Samudrala)
13) Netlink extended ACK support (Johannes Berg, Pablo Neira Ayuso,
and several others)
14) IPSEC hw offload infrastructure (Steffen Klassert)"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2065 commits)
tipc: refactor function tipc_sk_recv_stream()
tipc: refactor function tipc_sk_recvmsg()
net: thunderx: Optimize page recycling for XDP
net: thunderx: Support for XDP header adjustment
net: thunderx: Add support for XDP_TX
net: thunderx: Add support for XDP_DROP
net: thunderx: Add basic XDP support
net: thunderx: Cleanup receive buffer allocation
net: thunderx: Optimize CQE_TX handling
net: thunderx: Optimize RBDR descriptor handling
net: thunderx: Support for page recycling
ipx: call ipxitf_put() in ioctl error path
net: sched: add helpers to handle extended actions
qed*: Fix issues in the ptp filter config implementation.
qede: Fix concurrency issue in PTP Tx path processing.
stmmac: Add support for SIMATIC IOT2000 platform
net: hns: fix ethtool_get_strings overflow in hns driver
tcp: fix wraparound issue in tcp_lp
bpf, arm64: fix jit branch offset related to ldimm64
bpf, arm64: implement jiting of BPF_XADD
...
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 4.12:
API:
- Add batch registration for acomp/scomp
- Change acomp testing to non-unique compressed result
- Extend algorithm name limit to 128 bytes
- Require setkey before accept(2) in algif_aead
Algorithms:
- Add support for deflate rfc1950 (zlib)
Drivers:
- Add accelerated crct10dif for powerpc
- Add crc32 in stm32
- Add sha384/sha512 in ccp
- Add 3des/gcm(aes) for v5 devices in ccp
- Add Queue Interface (QI) backend support in caam
- Add new Exynos RNG driver
- Add ThunderX ZIP driver
- Add driver for hardware random generator on MT7623 SoC"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (101 commits)
crypto: stm32 - Fix OF module alias information
crypto: algif_aead - Require setkey before accept(2)
crypto: scomp - add support for deflate rfc1950 (zlib)
crypto: scomp - allow registration of multiple scomps
crypto: ccp - Change ISR handler method for a v5 CCP
crypto: ccp - Change ISR handler method for a v3 CCP
crypto: crypto4xx - rename ce_ring_contol to ce_ring_control
crypto: testmgr - Allow ecb(cipher_null) in FIPS mode
Revert "crypto: arm64/sha - Add constant operand modifier to ASM_EXPORT"
crypto: ccp - Disable interrupts early on unload
crypto: ccp - Use only the relevant interrupt bits
hwrng: mtk - Add driver for hardware random generator on MT7623 SoC
dt-bindings: hwrng: Add Mediatek hardware random generator bindings
crypto: crct10dif-vpmsum - Fix missing preempt_disable()
crypto: testmgr - replace compression known answer test
crypto: acomp - allow registration of multiple acomps
hwrng: n2 - Use devm_kcalloc() in n2rng_probe()
crypto: chcr - Fix error handling related to 'chcr_alloc_shash'
padata: get_next is never NULL
crypto: exynos - Add new Exynos RNG driver
...
Pull timer updates from Thomas Gleixner:
"The timer departement delivers:
- more year 2038 rework
- a massive rework of the arm achitected timer
- preparatory patches to allow NTP correction of clock event devices
to avoid early expiry
- the usual pile of fixes and enhancements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (91 commits)
timer/sysclt: Restrict timer migration sysctl values to 0 and 1
arm64/arch_timer: Mark errata handlers as __maybe_unused
Clocksource/mips-gic: Remove redundant non devicetree init
MIPS/Malta: Probe gic-timer via devicetree
clocksource: Use GENMASK_ULL in definition of CLOCKSOURCE_MASK
acpi/arm64: Add SBSA Generic Watchdog support in GTDT driver
clocksource: arm_arch_timer: add GTDT support for memory-mapped timer
acpi/arm64: Add memory-mapped timer support in GTDT driver
clocksource: arm_arch_timer: simplify ACPI support code.
acpi/arm64: Add GTDT table parse driver
clocksource: arm_arch_timer: split MMIO timer probing.
clocksource: arm_arch_timer: add structs to describe MMIO timer
clocksource: arm_arch_timer: move arch_timer_needs_of_probing into DT init call
clocksource: arm_arch_timer: refactor arch_timer_needs_probing
clocksource: arm_arch_timer: split dt-only rate handling
x86/uv/time: Set ->min_delta_ticks and ->max_delta_ticks
unicore32/time: Set ->min_delta_ticks and ->max_delta_ticks
um/time: Set ->min_delta_ticks and ->max_delta_ticks
tile/time: Set ->min_delta_ticks and ->max_delta_ticks
score/time: Set ->min_delta_ticks and ->max_delta_ticks
...
-----BEGIN PGP SIGNATURE-----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=NymV
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Pull "Fix DTC warnings in Exynos ARMv7 Device Tree sources." from Krzysztof Kozłowski:
* tag 'samsung-dt-4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Use - instead of @ for DT OPP entries
A single fix to remove device tree warnings introduced with recently
added checks in DTC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=kv8P
-----END PGP SIGNATURE-----
Merge tag 'vexpress-dt-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/dt
Pull "ARMv7 VExpress DT fix for v4.12" from Sudeep Holla:
A single fix to remove device tree warnings introduced with recently
added checks in DTC
* tag 'vexpress-dt-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
ARM: dts: vexpress: fix few unit address format warnings
Compiling the DT file with W=1, DTC warns like follows:
Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property
Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
[k.kozlowski: Split patch per ARM and ARM64]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
A function in kernel/bpf/syscall.c which got a bug fix in 'net'
was moved to kernel/bpf/verifier.c in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The SPEAr600 has a built-in ADC, which already has a Device Tree binding
described in
Documentation/devicetree/bindings/staging/iio/adc/spear-adc.txt. This
commit adds the description in the SPEAr600 Device Tree of this ADC
device.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The spear6xx doesn't have a pinctrl driver, since the pinmux is globally
defined through a single register, generally configured by the
firmware/bootloader.
Therefore, the pinctrl related properties in spear600-evb.dts are not
necessary.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This commit moves spear600-evb.dts to use the new flash partition Device
Tree binding documented in
Documentation/devicetree/bindings/mtd/partition.txt.
As this Device Tree binding document says: "For backwards compatibility
partitions as direct subnodes of the mtd device are supported. This use
is discouraged."
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This commit fixes a minor coding style issue in spear600-evb.dts:
missing spaces around equal sign.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Now that we have introduced node labels in spear600.dtsi, we can use
them for spear600-evb.dts.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Having labels allows to more easily reference nodes in .dts files
including spear600.dtsi.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
A bunch of clean up for Alpine device trees, nothing fancy.
-----BEGIN PGP SIGNATURE-----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=aD3G
-----END PGP SIGNATURE-----
Merge tag 'alpine-dt-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/atenart/linux into next/dt
Alpine DT changes for 4.12
A bunch of clean up for Alpine device trees, nothing fancy.
* tag 'alpine-dt-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/atenart/linux:
ARM: dts: alpine: add valid clock-frequency values
ARM: dts: alpine: add spaces before the uart node units.
ARM: dts: alpine: remove 0x's from the uart1 node unit address
ARM: dts: alpine: fix PCIe node name
Signed-off-by: Olof Johansson <olof@lixom.net>
Use label for USB and SATA nodes on Armada 38x
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWO+kqSMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71V2vAJ47Vu37Pig3
Quq7c68ByWMNhRv0IgCgpJOKmYRrcibw/AbrHIh6ZZUoN7g=
=AtGR
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.12-3' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt for 4.12 (part 3)
Use label for USB and SATA nodes on Armada 38x
* tag 'mvebu-dt-4.12-3' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada-38x: label USB and SATA nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
Updates to the device tree to include upstreamed drivers:
- SPI flash controller
- Watchdog
- ADC
In addition we describe some of the clocks so that upstream kernels can
boot on hardware.
-----BEGIN PGP SIGNATURE-----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=bGNK
-----END PGP SIGNATURE-----
Merge tag 'aspeed-4.12-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into next/dt
Aspeed devicetree updates for 4.12
Updates to the device tree to include upstreamed drivers:
- SPI flash controller
- Watchdog
- ADC
In addition we describe some of the clocks so that upstream kernels can
boot on hardware.
* tag 'aspeed-4.12-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
arm: dts: aspeed: Describe ADCs for AST2400/AST2500
ARM: dts: aspeed: romulus: Add UART1
ARM: dts: aspeed: Update watchdog compatible strings
ARM: dts: aspeed: Add a fastread property
ARM: dts: aspeed: Add SPI controller bindings to Romulus
ARM: dts: aspeed: Make G4 clocks fixed
ARM: dts: aspeed: Make G5 clocks fixed
ARM: dts: aspeed: add SPI controller bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
to configure various devices:
- Enable DCAN on am57xx-idk
- Enable CPSW ethernet0 and 1 on am335x-icev2
- Non-critical fix for droid 4 PMIC interrupt triggering
- Stop disabling SRAM and GPMC on droid 4
- Configure CPCAP PMIC related devices on droid 4 for ADC, charger
and USB PHY. The charger and USB PHY drivers are still being
discussed, but the binding for them has been acked by Rob and
Sebastian so they should be safe to merge together with the ADC
driver in Linux next that they depend on
-----BEGIN PGP SIGNATURE-----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=Jna8
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.12/dt-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Second set of devicetree changes for omaps for v4.12 merge window
to configure various devices:
- Enable DCAN on am57xx-idk
- Enable CPSW ethernet0 and 1 on am335x-icev2
- Non-critical fix for droid 4 PMIC interrupt triggering
- Stop disabling SRAM and GPMC on droid 4
- Configure CPCAP PMIC related devices on droid 4 for ADC, charger
and USB PHY. The charger and USB PHY drivers are still being
discussed, but the binding for them has been acked by Rob and
Sebastian so they should be safe to merge together with the ADC
driver in Linux next that they depend on
* tag 'omap-for-v4.12/dt-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap4-droid4: Add CPCAP PMIC OTG PHY configuration
ARM: dts: omap4-droid4: Add CPCAP PMIC battery charger configuration
ARM: dts: omap4-droid4: Add CPCAP PMIC ADC configuration
ARM: dts: omap4-droid4: Stop disabling SRAM and GPMC
ARM: dts: omap4-droid4: Fix interrupt triggering for cpcap
ARM: dts: am335x-icev2: Add CPSW ethernet0 and ethernet1
ARM: dts: am57xx-idk: Add DCAN support
Signed-off-by: Olof Johansson <olof@lixom.net>
- New board support: I2SE's i.MX28 Duckbill-2 boards, Gateworks Ventana
i.MX6 GW5903/GW5904, Zodiac Inflight Innovations RDU2 board, Engicam
i.CoreM6 Quad/Dual OpenFrame modules, Boundary Device i.MX6 Quad Plus
SOM.
- Improve compatible string for i.MX50 eSDHC, i.MX7S SRC devices and
i.MX6SX UART device.
- Add interrupts for switch and PHY devices on VF610 ZII Devel C board.
- Add LVDS, LCD backlight, touchscreen and SAI2 support for i.MX6
icore, geam, and isiot boards.
- A series from Lucas Stach to improve i.MX6Q Plus device tree and add
PRE/PRG devices.
- A series from Stefan Agner to update imx7-colibri device tree
regarding to display, PMIC/regulator support.
- Fix PCI bus DTC warnings seen with the latest compiler.
- Set default phy_type and dr_mode for i.MX25 USBOTG port.
- A couple of small improvements on i.MX25 pin function DT header.
- Add audio support for imx6q-cm-fx6 board using Wolfson wm8731 codec
which is muxed to SSI2 device.
- Other random updates, small fixes and trivial cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJY65XcAAoJEFBXWFqHsHzO0goH/jVVtrnkbfzjEZ+jSU30XY+L
8kR/R+5+PgT3LXZ/U3ZHWqbLOrYtnsmqUjA4loaRwTfyMEPnkRx86XUE86U/xfVy
FuWhFuQ/lLDyfon/CvrEXQ73+CTq8Q5PBqKefg9twi5fNkN2wRqVCD5i4cVgxMpi
KF6DchLv0eW2Zn6fYySf4zNcOIvbkma/qn/Ju2kZEP6TKadIgYvX5Tcw47d2fKsv
E5vypBXdWlNV4SzZyAm4CS9X3pjIQa8zIXHyJAeiqBY/2H7u6z/UvOqnRt0RFnX5
eaVtHF2DwuC9DyjyNVBK1Fhi/7++nnmbLRvBK9G4LBZNmIbcWJEVMHsQcsDQ2h8=
=hpdP
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
i.MX device tree updates for 4.12:
- New board support: I2SE's i.MX28 Duckbill-2 boards, Gateworks Ventana
i.MX6 GW5903/GW5904, Zodiac Inflight Innovations RDU2 board, Engicam
i.CoreM6 Quad/Dual OpenFrame modules, Boundary Device i.MX6 Quad Plus
SOM.
- Improve compatible string for i.MX50 eSDHC, i.MX7S SRC devices and
i.MX6SX UART device.
- Add interrupts for switch and PHY devices on VF610 ZII Devel C board.
- Add LVDS, LCD backlight, touchscreen and SAI2 support for i.MX6
icore, geam, and isiot boards.
- A series from Lucas Stach to improve i.MX6Q Plus device tree and add
PRE/PRG devices.
- A series from Stefan Agner to update imx7-colibri device tree
regarding to display, PMIC/regulator support.
- Fix PCI bus DTC warnings seen with the latest compiler.
- Set default phy_type and dr_mode for i.MX25 USBOTG port.
- A couple of small improvements on i.MX25 pin function DT header.
- Add audio support for imx6q-cm-fx6 board using Wolfson wm8731 codec
which is muxed to SSI2 device.
- Other random updates, small fixes and trivial cleanups.
* tag 'imx-dt-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (56 commits)
ARM: dts: imx6q-utilite-pro: add hpd gpio
ARM: dts: imx6qp-sabresd: Set reg_arm regulator supply
ARM: dts: imx6qdl-sabresd: Set LDO regulator supply
ARM: dts: imx: add Gateworks Ventana GW5903 support
ARM: dts: i.MX25: add AIPS control registers
ARM: dts: imx7-colibri: add Carrier Board 3.3V/5V regulators
ARM: dts: imx7-colibri: remove 1.8V fixed regulator
ARM: dts: imx7-colibri: allow to disable Ethernet rail
ARM: dts: imx7-colibri: fix PMIC voltages
ARM: dts: imx7-colibri: use OF graph to describe the display
ARM: dts: imx6qp-nitrogen6_som2: add Quad Plus variant of the SOM
ARM: dts: imx6q-icore: Add touchscreen node
ARM: dts: vf610-zii-dev-rev-b: change switch2 label
ARM: dts: imx6ul-[geam|isiot]: Add sai2 node
ARM: dts: imx6ul-isiot-common: Add touchscreen node
ARM: dts: imx6ul-isiot: Add i2c nodes
ARM: dts: imx6ul-isiot: Add imx6ul-isiot-common.dtsi
ARM: dts: imx6ul-isiot: Add backlight support for lcdif
ARM: dts: imx6ul-geam: Add backlight support for lcdif
ARM: dts: imx6: add ZII RDU2 boards
...
Signed-off-by: Olof Johansson <olof@lixom.net>
board, the phyCORE som and its PCM-947 carrier board from Phytec.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAljpQsEQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgSw5CACTf+7cvykZ3aKvtfo76yacC84mSMdLFOQl
IPkQBX6cV2CEes8xoKjsHXwvYgpgX6Jz58S86ATfi+h3uMu4l7dld+yMaipTcZp/
ROCtf16r+sjq3kndDGoqSFyq5+YZ2En+mz+86YDdEYS3vZvASp+gSVRkn7NUPlrU
+O2Wb8mdY+Hl8XYSZcsmQ7zNjxw/G9pyqVly0/3aSuHRVAbtn4KyunbfkhHdK4LJ
NOFji0t+FIXEr8FNBpiRFnIQ19KILzWmrIr5c92Tz+t11R8+wSIwITYpsAomwVqO
QWtI1alwusJHY2MwdLXlFtBAW3BwsTt72gasl6AigpvYIP0AxKna
=R6eU
-----END PGP SIGNATURE-----
Merge tag 'v4.12-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Support for the usb-sata controller on the rock2 and another new rk3288
board, the phyCORE som and its PCM-947 carrier board from Phytec.
* tag 'v4.12-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add support for PCM-947 carrier board
dt-bindings: Document Phytec phyCORE-RK3288 RDK
ARM: dts: rockchip: Add support for phyCORE-RK3288 SoM
ARM: dts: rockchip: Enable sata support on rock2 square
Signed-off-by: Olof Johansson <olof@lixom.net>
1. Enhancements to PCIe nodes on Exynos5440.
2. Fix thermal values on some of Exynos5420 boards like Odroid XU3.
3. Add proper clock frequency properties to DSI nodes.
4. Fix watchdog reset on Exynos4412.
5. Fix watchdog infinite interrupt in soft mode on Exynos4210,
Exynos5440, S3C64xx and S5Pv210.
6. Enable watchdog on Exynos4 and S3C SoCs.
-----BEGIN PGP SIGNATURE-----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=QHlh
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Samsung DeviceTree ARM update for v4.12:
1. Enhancements to PCIe nodes on Exynos5440.
2. Fix thermal values on some of Exynos5420 boards like Odroid XU3.
3. Add proper clock frequency properties to DSI nodes.
4. Fix watchdog reset on Exynos4412.
5. Fix watchdog infinite interrupt in soft mode on Exynos4210,
Exynos5440, S3C64xx and S5Pv210.
6. Enable watchdog on Exynos4 and S3C SoCs.
* tag 'samsung-dt-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: add HDMI controller phandle to exynos4.dtsi
ARM: dts: s5pv210: Fix infinite interrupt in soft mode
ARM: dts: s3c64xx: Fix infinite interrupt in soft mode
ARM: dts: exynos: Fix infinite interrupt in soft mode on Exynos4210 and Exynos5440
ARM: dts: exynos: Enable watchdog on all Exynos4 boards
ARM: dts: s3c64xx: Enable watchdog on all S3C64xx boards
ARM: dts: exynos: Fix watchdog reset on Exynos4412
ARM: dts: exynos: Add the burst and esc clock frequency properties to DSI node
ARM: dts: exynos: Do not ignore real-world fuse values for thermal zone 0 on Exynos5420
ARM: dts: exynos: Add phy-pcie node for pcie to Exynos5440
Signed-off-by: Olof Johansson <olof@lixom.net>
Use disk-activity trigger for armada-385-linksys
Keep dts alphabetically ordered for clearfog (Armada 388)
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWOgNoSMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71V3cAJ9gBnFQKIkt
jDbi9jpxM7vxznt0VgCgnnYcZsFjE7jFAxs+w4KDVd3jYo8=
=XQtw
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.12-2' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt for 4.12 (part 2)
Use disk-activity trigger for armada-385-linksys
Keep dts alphabetically ordered for clearfog (Armada 388)
* tag 'mvebu-dt-4.12-2' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada-385-linksys: disk-activity trigger for all
ARM: dts: clearfog: keep dts alphabetically ordered
Signed-off-by: Olof Johansson <olof@lixom.net>
Corrections:
* Correct clock frequency of X2 DU clock input for r8a7791/koelsch board
* Correct Z clock for r8a7792 SoC
* Correct parent of SSI[0-9] clocks for r8a779[013] SoCs
* Correct ethernet clock parent on r7s72100 SoC
* Correct DU clock for r8a7794/silk board
Cleanups:
* Drop _clk suffix from external CAN clock node name on r8a779[01] SoCs
Enhancements:
* Enable rtc r7s72100/genmai board
* Add Z2 clock for r8a7794 SoC
* Add DU clock for r8a7794 SoC
* Add power-domains to SDHI for r8a7794 and r7s72100 SoCs
* Add reset control properties for r8a774[35] SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=N8Dk
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt2-for-v4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Second Round of Renesas ARM Based SoC DT Updates for v4.12
Corrections:
* Correct clock frequency of X2 DU clock input for r8a7791/koelsch board
* Correct Z clock for r8a7792 SoC
* Correct parent of SSI[0-9] clocks for r8a779[013] SoCs
* Correct ethernet clock parent on r7s72100 SoC
* Correct DU clock for r8a7794/silk board
Cleanups:
* Drop _clk suffix from external CAN clock node name on r8a779[01] SoCs
Enhancements:
* Enable rtc r7s72100/genmai board
* Add Z2 clock for r8a7794 SoC
* Add DU clock for r8a7794 SoC
* Add power-domains to SDHI for r8a7794 and r7s72100 SoCs
* Add reset control properties for r8a774[35] SoCs
* tag 'renesas-dt2-for-v4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (22 commits)
ARM: dts: r8a7791: Drop _clk suffix from external CAN clock node name
ARM: dts: r8a7790: Drop _clk suffix from external CAN clock node name
ARM: dts: genmai: Enable rtc and rtc_x1 clock
ARM: dts: rskrza1: add rtc DT support
ARM: dts: rskrza1: set rtc_x1 clock value
ARM: dts: r7s72100: add rtc to device tree
ARM: dts: r7s72100: add RTC_X clock inputs to device tree
ARM: dts: r7s72100: add rtc clock to device tree
ARM: dts: koelsch: Correct clock frequency of X2 DU clock input
ARM: dts: r8a7794: Add Z2 clock
ARM: dts: r8a7792: Correct Z clock
ARM: dts: r8a7793: Correct parent of SSI[0-9] clocks
ARM: dts: r8a7791: Correct parent of SSI[0-9] clocks
ARM: dts: r8a7790: Correct parent of SSI[0-9] clocks
ARM: dts: r7s72100: fix ethernet clock parent
ARM: dts: silk: Correct clock of DU1
ARM: dts: alt: Correct clock of DU1
ARM: dts: r8a7794: Correct clock of DU1
ARM: dts: r8a7794: Add DU1 clock to device tree
ARM: dts: r7s72100: add power-domains to sdhi
...
Signed-off-by: Olof Johansson <olof@lixom.net>
H5 patches for 4.12, which are mostly related to reworking the H3 DTSI to
be usable on the arm64 H5 DTSI, that shares almost everything with the H3
but the CPU cores.
We then have patches to support the H5 boards on top.
-----BEGIN PGP SIGNATURE-----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=ilmt
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-h5-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt64
Allwinner H5 DT changes for 4.12
H5 patches for 4.12, which are mostly related to reworking the H3 DTSI to
be usable on the arm64 H5 DTSI, that shares almost everything with the H3
but the CPU cores.
We then have patches to support the H5 boards on top.
* tag 'sunxi-dt-h5-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: sunxi: h3/h5: switch apb0-related clocks to r_ccu
arm64: allwinner: h5: enable USB OTG on Orange Pi PC 2 board
arm64: allwinner: h5: add support for the Orange Pi PC 2 board
arm64: allwinner: h5: add Allwinner H5 .dtsi
ARM: sunxi: h3/h5: add usb_otg and OHCI/EHCI for usbc0 on H3/H5
arm: sun8i: h3: split Allwinner H3 .dtsi
arm: sun8i: h3: correct the GIC compatible in H3 to gic-400
arm: sun8i: h3: drop pinctrl-a10.h inclusion for H3 DTSI
arm: sun8i: h3: drop skeleton.dtsi inclusion in H3 DTSI
Signed-off-by: Olof Johansson <olof@lixom.net>
H3 patches for 4.12, which are mostly related to reworking the H3 DTSI to
be usable on the arm64 H5 DTSI, that shares almost everything with the H3
but the CPU cores.
We also have some new device addition (USB, mostly) that would conflict
otherwise.
-----BEGIN PGP SIGNATURE-----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=zcf9
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-h3-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner H3 DT changes for 4.12
H3 patches for 4.12, which are mostly related to reworking the H3 DTSI to
be usable on the arm64 H5 DTSI, that shares almost everything with the H3
but the CPU cores.
We also have some new device addition (USB, mostly) that would conflict
otherwise.
* tag 'sunxi-dt-h3-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: sun8i: h2+: enable USB OTG for Orange Pi Zero board
ARM: sun8i: h3: enable USB OTG on Orange Pi One
ARM: sunxi: h3/h5: add usb_otg and OHCI/EHCI for usbc0 on H3/H5
arm: sun8i: h3: split Allwinner H3 .dtsi
arm: sun8i: h3: correct the GIC compatible in H3 to gic-400
arm: sun8i: h3: drop pinctrl-a10.h inclusion for H3 DTSI
arm: sun8i: h3: drop skeleton.dtsi inclusion in H3 DTSI
Signed-off-by: Olof Johansson <olof@lixom.net>
As usual a number of changes, among which:
- All the sun5i DTSI has been reworked based on the new documentation and
the IPs that are actually found in all those SoCs. Part of that rework
also brought the GR8 DTSI to include sun5i.dtsi
- Mali devfreq and thermal throttling support on the A33
- AC power supplies for the AXP209 and AXP22X PMIC
- CAN support for the A20
- CPUFreq-based thermal throttling for the A33
- New board: NanoPi NEO Air
-----BEGIN PGP SIGNATURE-----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=m9vZ
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner DT changes for 4.12
As usual a number of changes, among which:
- All the sun5i DTSI has been reworked based on the new documentation and
the IPs that are actually found in all those SoCs. Part of that rework
also brought the GR8 DTSI to include sun5i.dtsi
- Mali devfreq and thermal throttling support on the A33
- AC power supplies for the AXP209 and AXP22X PMIC
- CAN support for the A20
- CPUFreq-based thermal throttling for the A33
- New board: NanoPi NEO Air
* tag 'sunxi-dt-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (38 commits)
ARM: sun8i: sina33: add highest OPP of CPUs
ARM: sun8i: a33: Add devfreq-based GPU cooling
ARM: sun8i: a33: add CPU thermal throttling
ARM: sun8i: a33: add thermal sensor
ARM: dts: sun7i: fix device node ordering
ARM: dts: sun4i: fix device node ordering
ARM: dts: sun7i: Add can0_pins_a pinctrl settings
ARM: dts: sun7i: Add CAN node
ARM: dts: sun4i: Add can0_pins_a pinctrl settings
ARM: dts: sun4i: Add CAN node
ARM: sun7i: cubietruck: enable ACIN und USB power supply subnode
ARM: dts: sun5i: Add interrupt for display backend
dt-bindings: display: sun4i: Add display backend interrupt to device tree binding
ARM: dts: sun7i: Use axp209.dtsi on A20-OLinuXino-Micro
ARM: dts: sun6i: sina31s: Enable SPDIF out
ARM: sun8i: sina33: add cpu-supply
ARM: sun8i: a33: add all operating points
ARM: sun5i: chip: enable ACIN power supply subnode
ARM: dts: sun8i: sina33: enable ACIN power supply subnode
ARM: dtsi: axp22x: add AC power supply subnode
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- Clean-up:
- Add clock/memory nodes
- Add labels for CPU nodes
- Remove unused unit names and reg
- Remove unused skeleton.dtsi
- Add support for PMU
- Add QSPI for sodia board
- Add Reset controller for Arria10
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=EeLo
-----END PGP SIGNATURE-----
Merge tag 'socfpga_dts_for_v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt
SoCFPGA DTS updates for v4.12
- Clean-up:
- Add clock/memory nodes
- Add labels for CPU nodes
- Remove unused unit names and reg
- Remove unused skeleton.dtsi
- Add support for PMU
- Add QSPI for sodia board
- Add Reset controller for Arria10
* tag 'socfpga_dts_for_v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: socfpga: Add Devkit A10-SR Reset Controller
ARM: dts: socfpga: sodia: enable qspi
ARM: dts: socfpga: Add support for PMU
ARM: dts: socfpga: Add labels for CPU nodes
ARM: dts: socfpga: Do not include skeleton.dtsi
ARM: dts: socfpga: Remove unit name for LEDs in EBV SOCrates
ARM: dts: socfpga: Remove unneeded reg from stmpe_touchscreen
ARM: dts: socfpga: Remove unneeded unit names
ARM: dts: socfpga: Add unit name to memory nodes
ARM: dts: socfpga: Add unit name to clock nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
Highlights:
----------
- ADD RTC support on STM32F746 MCU
- Enable RTC on STM32F746 Eval board
- Enable clocks on STM32F746 MCU
- Enable DMA, pwm1 and pwm3 on STM32F429I Eval
- Add support of STM32H743 MCU and his Eval board
- Enable USB HS and FS on STM32F469 Disco board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=l7eq
-----END PGP SIGNATURE-----
Merge tag 'stm32-dt-for-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into next/dt
STM32 DT updates for v4.12, round 1
Highlights:
----------
- ADD RTC support on STM32F746 MCU
- Enable RTC on STM32F746 Eval board
- Enable clocks on STM32F746 MCU
- Enable DMA, pwm1 and pwm3 on STM32F429I Eval
- Add support of STM32H743 MCU and his Eval board
- Enable USB HS and FS on STM32F469 Disco board
* tag 'stm32-dt-for-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
dt-bindings: Document the STM32 USB OTG DWC2 core binding
ARM: dts: stm32: Enable USB HS in FS mode (embedded phy) on stm32f429-disco
ARM: dts: stm32: Enable USB FS on stm32f469-disco
ARM: dts: stm32: Add USB FS support for STM32F429 MCU
ARM: dts: stm32: Add STM32H743 MCU and STM32H743i-EVAL board
ARM: dts: stm32: Enable pwm1 and pwm3 on stm32f429i-eval
ARM: dts: stm32: Enable dma by default on stm32f4 adc
ARM: dts: stm32: enable RTC on stm32746g-eval
ARM: dts: stm32: Add RTC support for STM32F746 MCU
ARM: dts: stm32: set HSE_RTC clock frequency to 1 MHz on stm32f746
dt-bindings: mfd: Add STM32F7 RCC numeric constants into DT include file
ARM: dts: stm32: Enable clocks for STM32F746 MCU
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch fixes the following set of warnings on vexpress platforms:
sysreg@010000 simple-bus unit address format error, expected "10000"
sysctl@020000 simple-bus unit address format error, expected "20000"
i2c@030000 simple-bus unit address format error, expected "30000"
aaci@040000 simple-bus unit address format error, expected "40000"
mmci@050000 simple-bus unit address format error, expected "50000"
kmi@060000 simple-bus unit address format error, expected "60000"
kmi@070000 simple-bus unit address format error, expected "70000"
uart@090000 simple-bus unit address format error, expected "90000"
uart@0a0000 simple-bus unit address format error, expected "a0000"
uart@0b0000 simple-bus unit address format error, expected "b0000"
uart@0c0000 simple-bus unit address format error, expected "c0000"
wdt@0f0000 simple-bus unit address format error, expected "f0000"
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Again, a batch that's been sitting a couple of weeks, mostly because I
anticipated a bit more material but it didn't show up -- which is good.
These are all your garden variety fixes for ARM platforms. Most visible issue
fixed here is probably the SMP reset issue on OMAP, the rest are minor stuff.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=C+Hz
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Again, a batch that's been sitting a couple of weeks, mostly because
I anticipated a bit more material but it didn't show up -- which is
good.
These are all your garden variety fixes for ARM platforms.
The most visible issue fixed here is probably the SMP reset issue on
OMAP, the rest are minor stuff"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: allwinner: a64: add pmu0 regs for USB PHY
ARM: OMAP2+: omap_device: Sync omap_device and pm_runtime after probe defer
reset: add exported __reset_control_get, return NULL if optional
ARM: orion5x: only call into phylib when available
ARM: omap2+: Revert omap-smp.c changes resetting CPU1 during boot
ARM: dts: am335x-evmsk: adjust mmc2 param to allow suspend
ARM: dts: ti: fix PCI bus dtc warnings
ARM: dts: am335x-baltos: disable EEE for Atheros 8035 PHY
ARM: dts: OMAP3: Fix MFG ID EEPROM
ARM: sun8i: a33: add operating-points-v2 property to all nodes
ARM: sun8i: a33: remove highest OPP to fix CPU crashes
Without this fix we can get PM related warnings for devices that
use deferred probe. If necessary, this fix can wait for the
v4.12 merge window no problem.
-----BEGIN PGP SIGNATURE-----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=07Xj
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.11/fixes-rc6-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Regression fix for omap interconnect code for deferred probe.
Without this fix we can get PM related warnings for devices that
use deferred probe. If necessary, this fix can wait for the
v4.12 merge window no problem.
* tag 'omap-for-v4.11/fixes-rc6-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: omap_device: Sync omap_device and pm_runtime after probe defer
ARM: omap2+: Revert omap-smp.c changes resetting CPU1 during boot
ARM: dts: am335x-evmsk: adjust mmc2 param to allow suspend
ARM: dts: ti: fix PCI bus dtc warnings
ARM: dts: am335x-baltos: disable EEE for Atheros 8035 PHY
ARM: dts: OMAP3: Fix MFG ID EEPROM
Signed-off-by: Olof Johansson <olof@lixom.net>
Remove ADC channels that are not available by default on the sama5d3_xplained
board (resistor not populated) in order to not create confusion.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: <stable@vger.kernel.org> # 3.16+
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The voltage reference for the ADC is not 3V but 3.3V since it is connected to
VDDANA.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: <stable@vger.kernel.org> # 3.16+
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The envelope detector can analyze 6 different signals, selectable with a
mux controlled by three gpio pins.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
We found out that HW checksum generation only works from AST2500
onward. This disables it on AST2400 and removes the "no-hw-checksum"
properties in the device-trees. The problem we had wasn't related
to NC-SI.
Also rework the logic testing for that property so it can be used
to disable HW checksum generation and checking regardless of whether
NC-SI is used or not in case other variants out there need this.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We test for aspeed chips to handle a couple of special cases,
but we do that by checking the machine type which isn't right.
Instead check the actual device compatible property. This also
updates the dtsi files for the aspeed SoC to match.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently most nodes got labels to make them referenceable. The USB 3.0
nodes as well as the nodes for the SATA controllers were left out,
rectify the omission.
The labels "sataX" are already used by some boards for the SATA ports,
therefore use "ahciX" to label the SATA controller nodes.
To avoid potential confusion by labeling an USB3.0 controller "usb2" use
usb3_X as labels. This also coincides with the node names themselves
(usb@xxxxx vs usb3@xxxxx).
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add the new hdmi phandle to exynos4.dtsi. This phandle is needed by the
s5p-cec driver to initialize the CEC notifier framework.
Tested with my Odroid U3.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: linux-samsung-soc@vger.kernel.org
CC: devicetree@vger.kernel.org
CC: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
To use CEC notifier sti CEC driver needs to get phandle
of the hdmi device.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
CC: Patrice CHOTARD <patrice.chotard@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The hpd pin of the second hdmi connector of the Utilite Pro is wired
up to a gpio pin of the SoC. Reflect this in the device tree.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On imx6qp-sabresd LDO_ARM is connected to a different PMIC output than
the other imx6qdl-sabresd boards.
Setting cpu0 arm-supply to sw2_reg is wrong, this must have mistakenly
slipped out of the vendor tree where this is are used for LDO bypass.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Setting the supply is optional but beneficial, it will cause PMIC
voltages to be dynamically changed with cpu frequency.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX25 contains two AHB to IP bridges (AIPS), each of which has a set of
control registers. Add the memory regions for the control registers to
the Device Tree.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Model the Carrier Board power distribution by adding a fixed 3.3V
and 5V regulator. The 3.3V regulator is connected to the backlight
as well as the display supply. The 5V regulator is used to supply
USB VBUS.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The ADC is directly supplied by the PMIC 1.8V rail, remove the
superfluous fixed regulator.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The regulator-always-on property on the Ethernet rail prevents Linux
from disabling the rail when Ethernet is shut down (suspend or simply
link down). With this change the regulator framework will disable the
rail when the Ethernet PHY is not used, saving power especially on
carrier board not using Ethernet.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix wrong voltage of PWR_EN_+V3.3 rail. The error had no noticeable
effect since no consumer explicitly requested a specific voltage.
Also use round voltages as it is common in other device trees.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
To make use of the new eLCDIF DRM driver OF graph description is
required. Describe the display using OF graph nodes.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Rename the switch2@0 label of the switch2 node to switch@0 to respect
the general unit@address DTS rule, and be consistent with the other
switch nodes of the DTS file.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for i2c nodes i2c1 and i2c2 on Is.IoT MX6UL
eMMC variant boards.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
lcdif nodes are differ wrt specific LCD connected on Is.IoT MX6UL
module, so create separate file 'imx6ul-isiot-common.dtsi' for common
lcdif node structure and include the same on respective dts.
More common nodes will add in future patches.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
