All Exynos 5250 SoCs have HDMI PHY connected via dedicated I2C bus (bus
number 8), so HDMI PHY should be defined in exynos5250.dtsi instead of
duplicating it in every board, which enables HDMI support.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Exynos 5250 and 5420 have different hardware rotation limits. However,
currently it uses only one compatible - "exynos5-gsc". Since we have
to distinguish between these two, we add different compatible.
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
GPIO keys don't need interrupt property. Interrupt number can be derived
directly from the GPIO pin definition, so remove redundant 'interrupts'
and 'interrupt-parent' properties from gpio-keys nodes on
Exynos4412-based Odroid boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The power button (SW2) on Odroid XU3/4 is connected to the PWRON pin
of the S2MPS11 PMIC.
The S2MPS11 datasheet says that ONOB pin operates as 'PWRON key active
low signal'. In fact, S2MPS11 PMIC acts as a 16ms debouce filter and
signal inverter, thus effectively repeating PWRON (active high) to ONOB
pin (active low).
ONOB PMIC pin is then connected to XEINT3 SoC pin, so we get the state
of the power button on the gpx0-3 GPIO.
This patch adds device-tree bindings for the power button of Odroid
XU3/4 boards.
Signed-off-by: Brian Kim <brian.kim@hardkernel.com>
[mszyprow: extended commit message, added comments and fixed minor
issues in the dts]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The display-timing and delay are included in the panel driver so they
should be removed from dts.
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The following 'capacity-dmips-mhz' dt property values are used:
Cortex-A15: 1024, Cortex-A7: 539
They have been derived form the cpu_efficiency values:
Cortex-A15: 3891, Cortex-A7: 2048
by scaling them so that the Cortex-A15s (big cores) use 1024.
The cpu_efficiency values were originally derived from the "Big.LITTLE
Processing with ARM Cortex™-A15 & Cortex-A7" white paper
(http://www.cl.cam.ac.uk/~rdm34/big.LITTLE.pdf). Table 1 lists 1.9x
(3891/2048) as the Cortex-A15 vs Cortex-A7 performance ratio for the
Dhrystone benchmark.
The following platforms are affected once cpu-invariant accounting
support is re-connected to the task scheduler:
odroidxu3, odroidxu3-lite, odroidxu4
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The following 'capacity-dmips-mhz' dt property values are used:
Cortex-A15: 1024, Cortex-A7: 539
They have been derived from the cpu_efficiency values:
Cortex-A15: 3891, Cortex-A7: 2048
by scaling them so that the Cortex-A15s (big cores) use 1024.
The cpu_efficiency values were originally derived from the "Big.LITTLE
Processing with ARM Cortex™-A15 & Cortex-A7" white paper
(http://www.cl.cam.ac.uk/~rdm34/big.LITTLE.pdf). Table 1 lists 1.9x
(3891/2048) as the Cortex-A15 vs Cortex-A7 performance ratio for the
Dhrystone benchmark.
The following platforms are affected once cpu-invariant accounting
support is re-connected to the task scheduler:
arndale-octa, peach-pi, peach-pit, smdk5420
The patch has been tested on Samsung Chromebook 2 13" (peach-pi, Exynos
5800).
$ cat /sys/devices/system/cpu/cpu*/cpu_capacity
1024
1024
1024
1024
389
389
389
389
The Cortex-A15 vs Cortex-A7 performance ratio is 1024/389 = 2.63.
The values derived with the 'cpu_efficiency/clock-frequency dt property'
solution are:
$ cat /sys/devices/system/cpu/cpu*/cpu_capacity
1535
1535
1535
1535
448
448
448
448
The Cortex-A15 vs Cortex-A7 performance ratio is 1535/448 = 3.43.
The discrepancy between 2.63 and 3.43 is due to the false assumption
when using the 'cpu_efficiency/clock-frequency dt property' solution
that the max cpu frequency of the little cpus is 1 GHZ and not 1.3 GHz.
The Cortex-A7 cluster runs with a max cpu frequency of 1.3 GHZ whereas
the 'clock-frequency' property value is set to 1 GHz.
3.43/1.3 = 2.64
$ cat /sys/devices/system/cpu/cpu*/cpufreq/scaling_max_freq
1800000
1800000
1800000
1800000
1300000 <-- max cpu frequency of the Cortex-A7s (little cores)
1300000
1300000
1300000
Running another benchmark (single-threaded sysbench affine to the
individual cpus) with performance cpufreq governor on the Samsung
Chromebook 2 13" showed the following numbers:
$ for i in `seq 0 7`; do taskset -c $i sysbench --test=cpu
--num-threads=1 --max-time=10 run | grep "total number of events:";
done
total number of events: 1083
total number of events: 1085
total number of events: 1085
total number of events: 1085
total number of events: 454
total number of events: 454
total number of events: 454
total number of events: 454
The Cortex-A15 vs Cortex-A7 performance ratio is 2.39, i.e. very close
to the one derived from the Dhrystone based one of the "Big.LITTLE
Processing with ARM Cortex™-A15 & Cortex-A7" white paper (2.63).
We don't aim for exact values for the cpu capacity values. Besides the
CPI (Cycles Per Instruction), the instruction mix and whether the system
runs cpu-bound or memory-bound has an impact on the cpu capacity values
derived from these benchmark results.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Odroid XU3/4 boards have thermal sensors per 4 pairs of A7+A15
cores but currently there is only one thermal-zone (including
cooling maps) defined (for the first pair of cores - the first
core of the A7 cluster and the first core of A15 cluster) so
i.e. if the task is running on any of A15 cores but the first
one, such core can reach high temperature without any proper
cooling action.
Fix it by adding missing thermal-zones definitions.
Also while at it fix the number of steps in cpufreq cooling for
cpu4 (11 steps for A15 corresponds to 700MHz, for 600MHz 12 steps
should be used).
Signed-off-by: Willy Wolff <willy.mh.wolff@gmail.com>
[b.zolnierkie: rewrote patch subject & description + minor fixups]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
As usual, device tree updates is the bulk of our material in this merge
window. This time around, 559 patches affecting both 32- and 64-bit
platforms.
Changes are too many to list individually, but some of the larger ones:
New platform/SoC support:
- Automotive:
+ Renesas R-Car D3 (R8A77995)
+ TI DT76x
+ MediaTek mt2712e
- Communication-oriented:
+ Qualcomm IPQ8074
+ Broadcom Stingray
+ Marvell Armada 8080
- Set top box:
+ Uniphier PXs3
Besides some vendor reference boards for the SoC above, there are also several
new boards/machines:
- TI AM335x Moxa UC-8100-ME-T open platform
- TI AM57xx Beaglebone X15 Rev C
- Microchip/Atmel sama5d27 SoM1 EK
- Broadcom Raspberry Pi Zero W
- Gemini-based D-Link DIR-685 router
- Freescale i.MX6:
+ Toradex Apalis module + Apalis and Ixora carrier boards
+ Engicam GEAM6UL Starter Kit
- Freescale i.MX53-based Beckhoff CX9020 Embedded PC
- Mediatek mt7623-based BananaPi R2
- Several Allwinner-based single-board computers:
+ Cubietruck plus
+ Bananapi M3, M2M and M64
+ NanoPi A64
+ A64-OLinuXino
+ Pine64
- Rockchip RK3328 Pine64/Rock64 board support
- Rockchip RK3399 boards:
+ RK3399 Sapphire module on Excavator carrier (RK3399 reference design)
+ Theobroma Systems RK3399-Q7 SoM
- ZTE ZX296718 PCBOX Board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=R45j
-----END PGP SIGNATURE-----
Merge tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM/arm64 Devicetree updates from Olof Johansson:
"As usual, device tree updates is the bulk of our material in this
merge window. This time around, 559 patches affecting both 32- and
64-bit platforms.
Changes are too many to list individually, but some of the larger
ones:
New platform/SoC support:
- Automotive:
+ Renesas R-Car D3 (R8A77995)
+ TI DT76x
+ MediaTek mt2712e
- Communication-oriented:
+ Qualcomm IPQ8074
+ Broadcom Stingray
+ Marvell Armada 8080
- Set top box:
+ Uniphier PXs3
Besides some vendor reference boards for the SoC above, there are also
several new boards/machines:
- TI AM335x Moxa UC-8100-ME-T open platform
- TI AM57xx Beaglebone X15 Rev C
- Microchip/Atmel sama5d27 SoM1 EK
- Broadcom Raspberry Pi Zero W
- Gemini-based D-Link DIR-685 router
- Freescale i.MX6:
+ Toradex Apalis module + Apalis and Ixora carrier boards
+ Engicam GEAM6UL Starter Kit
- Freescale i.MX53-based Beckhoff CX9020 Embedded PC
- Mediatek mt7623-based BananaPi R2
- Several Allwinner-based single-board computers:
+ Cubietruck plus
+ Bananapi M3, M2M and M64
+ NanoPi A64
+ A64-OLinuXino
+ Pine64
- Rockchip RK3328 Pine64/Rock64 board support
- Rockchip RK3399 boards:
+ RK3399 Sapphire module on Excavator carrier (RK3399 reference design)
+ Theobroma Systems RK3399-Q7 SoM
- ZTE ZX296718 PCBOX Board"
* tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (559 commits)
ARM: dts: at91: at91sam9g45: add AC97
arm64: dts: marvell: mcbin: enable more networking ports
arm64: dts: marvell: add a reference to the sysctrl syscon in the ppv2 node
arm64: dts: marvell: add TX interrupts for PPv2.2
arm64: dts: uniphier: add PXs3 SoC support
ARM: dts: uniphier: add pinctrl groups of ethernet phy mode
ARM: dts: uniphier: fix size of sdctrl nodes
ARM: dts: uniphier: add AIDET nodes
arm64: dts: uniphier: fix size of sdctrl node
arm64: dts: uniphier: add AIDET nodes
Revert "ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Beelink X2"
arm64: dts: uniphier: add reset controller node of analog amplifier
arm64: dts: marvell: add Device Tree files for Armada-8KP
arm64: dts: rockchip: add Haikou baseboard with RK3399-Q7 SoM
arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM
dt-bindings: add rk3399-q7 SoM
ARM: dts: rockchip: enable usb for rv1108-evb
ARM: dts: rockchip: add usb nodes for rv1108 SoCs
dt-bindings: update grf-binding for rv1108 SoCs
ARM: dts: aspeed-g4: fix AHB window size of the SMC controllers
...
This branch contains platform updates for 32- and 64-bit ARM,
including defconfig updates to enable new options, drivers and
platforms. There are also a few fixes and cleanups for some existing vendors.
Some of the things worth highlighting here are:
- Enabling new crypt drivers on arm64 defconfig
- QCOM IPQ8074 clocks and pinctrl drivers on arm64 defconfig
- Debug support enabled for Renesas r8a7743
- Various config updates for Renesas platforms (sound, USB, other drivers)
- Platform support (including SMP) for TI dra762
- OMAP cleanups: Move to use generic 8250 debug_ll, removal of stale DMA code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=g8cF
-----END PGP SIGNATURE-----
Merge tag 'armsoc-platforms' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM/arm64 SoC platform updates from Olof Johansson: "This branch
contains platform updates for 32- and 64-bit ARM, including defconfig
updates to enable new options, drivers and platforms. There are also a
few fixes and cleanups for some existing vendors.
Some of the things worth highlighting here are:
- Enabling new crypt drivers on arm64 defconfig
- QCOM IPQ8074 clocks and pinctrl drivers on arm64 defconfig
- Debug support enabled for Renesas r8a7743
- Various config updates for Renesas platforms (sound, USB, other
drivers)
- Platform support (including SMP) for TI dra762
- OMAP cleanups: Move to use generic 8250 debug_ll, removal of stale
DMA code"
* tag 'armsoc-platforms' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (109 commits)
ARM: multi_v7_defconfig: make eSDHC driver built-in
arm64: defconfig: enable rockchip graphics
MAINTAINERS: Update Cavium ThunderX2 entry
ARM: config: aspeed: Add I2C, VUART, LPC Snoop
ARM: configs: aspeed: Update Aspeed G4 with VMSPLIT_2G
ARM: s3c24xx: Fix NAND ECC mode for mini2440 board
ARM: davinci_all_defconfig: enable tinydrm and ST7586
arm64: defconfig: Enable QCOM IPQ8074 clock and pinctrl
ARM: defconfig: tegra: Enable ChipIdea UDC driver
ARM: configs: Add Tegra I2S interfaces to multi_v7_defconfig
ARM: tegra: Add Tegra I2S interfaces to defconfig
ARM: tegra: Update default configuration for v4.13-rc1
MAINTAINERS: update ARM/ZTE entry
soc: versatile: remove unnecessary static in realview_soc_probe()
ARM: Convert to using %pOF instead of full_name
ARM: hisi: Fix typo in comment
ARM: multi_v7_defconfig: add CONFIG_BRCMSTB_THERMAL
arm64: defconfig: add CONFIG_BRCMSTB_THERMAL
arm64: defconfig: add recently added crypto drivers as modules
arm64: defconfig: enable CONFIG_UNIPHIER_WATCHDOG
...
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
- New Device Support
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
- New Functionality
- Amend API to provide register layout; atmel-smc
- Fix-ups
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
- Bug Fixes
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll
-----BEGIN PGP SIGNATURE-----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=TKIm
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
New Device Support:
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
New Functionality:
- Amend API to provide register layout; atmel-smc
Fix-ups:
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
Bug Fixes:
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll"
* tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (61 commits)
mfd: intel_soc_pmic: Differentiate between Bay and Cherry Trail CRC variants
mfd: intel_soc_pmic: Export separate mfd-cell configs for BYT and CHT
dt-bindings: mfd: Add bindings for ZII RAVE devices
mfd: omap-usb-tll: Fix register offsets
mfd: da9052: Constify spi_device_id
mfd: intel-lpss: Put I2C and SPI controllers into reset state on suspend
mfd: da9055: Constify i2c_device_id
mfd: intel-lpss: Add missing PCI ID for Intel Sunrise Point LPSS devices
mfd: t7l66xb: Handle return value of clk_prepare_enable
mfd: Add ROHM BD9571MWV-M PMIC DT bindings
mfd: intel_soc_pmic_chtwc: Turn Kconfig option into a bool
mfd: lp87565: Convert to use devm_mfd_add_devices()
mfd: Add support for TPS68470 device
mfd: lpc_ich: Do not touch SPI-NOR write protection bit on Haswell/Broadwell
mfd: syscon: atmel-smc: Add helper to retrieve register layout
mfd: axp20x: Use correct platform device ID for many PEK
dt-bindings: mfd: axp20x: Introduce bindings for AXP813
mfd: axp20x: Add support for AXP813 PMIC
dt-bindings: mfd: axp20x: Add AXP806 to supported list of chips
mfd: Add ROHM BD9571MWV-M MFD PMIC driver
...
-----BEGIN PGP SIGNATURE-----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=fNM2
-----END PGP SIGNATURE-----
Merge tag 'media/v4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"Brazil's Independence Day pull request :-)
This is one of the biggest media pull requests, with 625 patches
affecting almost all parts of media (RC, DVB, V4L2, CEC, docs).
This contains:
- A lot of new drivers:
* DVB frontends: mxl5xx, stv0910, stv6111;
* camera flash: as3645a led driver;
* HDMI receiver: adv748X;
* camera sensor: Omnivision 6650 5M driver (ov6650);
* HDMI CEC: ao-cec meson driver;
* V4L2: Qualcom camss driver;
* Remote controller: gpio-ir-tx, pwm-ir-tx and zx-irdec drivers.
- The DDbridge DVB driver got a massive update, with makes it in sync
with modern hardware from that vendor;
- There's an important milestone on this series: the DVB
documentation was written in 2003, but only started to be updated
in 2007. It also used to contain several gaps from the time it was
kept out of tree, mentioning error codes and device nodes that
never existed upstream. On this series, it received a massive
update: all non-deprecated digital TV APIs are now in sync with the
current implementation;
- Some DVB APIs that aren't used by any upstream driver got removed;
- Other parts of the media documentation algo got updated, fixing
some bugs on its PDF output and making it compatible with Sphinx
version 1.6.
As the number of hacks required to build PDF output reduced, I hope
we'll have less troubles as newer versions of our documentation
toolchain are released (famous last words);
- As usual, lots of driver cleanups and improvements"
* tag 'media/v4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (624 commits)
media: leds: as3645a: add V4L2_FLASH_LED_CLASS dependency
media: get rid of removed DMX_GET_CAPS and DMX_SET_SOURCE leftovers
media: Revert "[media] v4l: async: make v4l2 coexist with devicetree nodes in a dt overlay"
media: staging: atomisp: sh_css_calloc shall return a pointer to the allocated space
media: Revert "[media] lirc_dev: remove superfluous get/put_device() calls"
media: add qcom_camss.rst to v4l-drivers rst file
media: dvb headers: make checkpatch happier
media: dvb uapi: move frontend legacy API to another part of the book
media: pixfmt-srggb12p.rst: better format the table for PDF output
media: docs-rst: media: Don't use \small for V4L2_PIX_FMT_SRGGB10 documentation
media: index.rst: don't write "Contents:" on PDF output
media: pixfmt*.rst: replace a two dots by a comma
media: vidioc-g-fmt.rst: adjust table format
media: vivid.rst: add a blank line to correct ReST format
media: v4l2 uapi book: get rid of driver programming's chapter
media: format.rst: use the right markup for important notes
media: docs-rst: cardlists: change their format to flat-tables
media: em28xx-cardlist.rst: update to reflect last changes
media: v4l2-event.rst: adjust table to fit on PDF output
media: docs: don't show ToC for each part on PDF output
...
Pull networking updates from David Miller:
1) Support ipv6 checksum offload in sunvnet driver, from Shannon
Nelson.
2) Move to RB-tree instead of custom AVL code in inetpeer, from Eric
Dumazet.
3) Allow generic XDP to work on virtual devices, from John Fastabend.
4) Add bpf device maps and XDP_REDIRECT, which can be used to build
arbitrary switching frameworks using XDP. From John Fastabend.
5) Remove UFO offloads from the tree, gave us little other than bugs.
6) Remove the IPSEC flow cache, from Florian Westphal.
7) Support ipv6 route offload in mlxsw driver.
8) Support VF representors in bnxt_en, from Sathya Perla.
9) Add support for forward error correction modes to ethtool, from
Vidya Sagar Ravipati.
10) Add time filter for packet scheduler action dumping, from Jamal Hadi
Salim.
11) Extend the zerocopy sendmsg() used by virtio and tap to regular
sockets via MSG_ZEROCOPY. From Willem de Bruijn.
12) Significantly rework value tracking in the BPF verifier, from Edward
Cree.
13) Add new jump instructions to eBPF, from Daniel Borkmann.
14) Rework rtnetlink plumbing so that operations can be run without
taking the RTNL semaphore. From Florian Westphal.
15) Support XDP in tap driver, from Jason Wang.
16) Add 32-bit eBPF JIT for ARM, from Shubham Bansal.
17) Add Huawei hinic ethernet driver.
18) Allow to report MD5 keys in TCP inet_diag dumps, from Ivan
Delalande.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1780 commits)
i40e: point wb_desc at the nvm_wb_desc during i40e_read_nvm_aq
i40e: avoid NVM acquire deadlock during NVM update
drivers: net: xgene: Remove return statement from void function
drivers: net: xgene: Configure tx/rx delay for ACPI
drivers: net: xgene: Read tx/rx delay for ACPI
rocker: fix kcalloc parameter order
rds: Fix non-atomic operation on shared flag variable
net: sched: don't use GFP_KERNEL under spin lock
vhost_net: correctly check tx avail during rx busy polling
net: mdio-mux: add mdio_mux parameter to mdio_mux_init()
rxrpc: Make service connection lookup always check for retry
net: stmmac: Delete dead code for MDIO registration
gianfar: Fix Tx flow control deactivation
cxgb4: Ignore MPS_TX_INT_CAUSE[Bubble] for T6
cxgb4: Fix pause frame count in t4_get_port_stats
cxgb4: fix memory leak
tun: rename generic_xdp to skb_xdp
tun: reserve extra headroom only when XDP is set
net: dsa: bcm_sf2: Configure IMP port TC2QOS mapping
net: dsa: bcm_sf2: Advertise number of egress queues
...
- Drop the P-state selection algorithm based on a PID controller
from intel_pstate and make it use the same P-state selection
method (based on the CPU load) for all types of systems in the
active mode (Rafael Wysocki, Srinivas Pandruvada).
- Rework the cpufreq core and governors to make it possible to
take cross-CPU utilization updates into account and modify the
schedutil governor to actually do so (Viresh Kumar).
- Clean up the handling of transition latency information in the
cpufreq core and untangle it from the information on which drivers
cannot do dynamic frequency switching (Viresh Kumar).
- Add support for new SoCs (MT2701/MT7623 and MT7622) to the
mediatek cpufreq driver and update its DT bindings (Sean Wang).
- Modify the cpufreq dt-platdev driver to autimatically create
cpufreq devices for the new (v2) Operating Performance Points
(OPP) DT bindings and update its whitelist of supported systems
(Viresh Kumar, Shubhrajyoti Datta, Marc Gonzalez, Khiem Nguyen,
Finley Xiao).
- Add support for Ux500 to the cpufreq-dt driver and drop the
obsolete dbx500 cpufreq driver (Linus Walleij, Arnd Bergmann).
- Add new SoC (R8A7795) support to the cpufreq rcar driver (Khiem
Nguyen).
- Fix and clean up assorted issues in the cpufreq drivers and core
(Arvind Yadav, Christophe Jaillet, Colin Ian King, Gustavo Silva,
Julia Lawall, Leonard Crestez, Rob Herring, Sudeep Holla).
- Update the IO-wait boost handling in the schedutil governor to
make it less aggressive (Joel Fernandes).
- Rework system suspend diagnostics to make it print fewer messages
to the kernel log by default, add a sysfs knob to allow more
suspend-related messages to be printed and add Low Power S0 Idle
constraints checks to the ACPI suspend-to-idle code (Rafael
Wysocki, Srinivas Pandruvada).
- Prefer suspend-to-idle over S3 on ACPI-based systems with the
ACPI_FADT_LOW_POWER_S0 flag set and the Low Power Idle S0 _DSM
interface present in the ACPI tables (Rafael Wysocki).
- Update documentation related to system sleep and rename a number
of items in the code to make it cleare that they are related to
suspend-to-idle (Rafael Wysocki).
- Export a variable allowing device drivers to check the target
system sleep state from the core system suspend code (Florian
Fainelli).
- Clean up the cpuidle subsystem to handle the polling state on
x86 in a more straightforward way and to use %pOF instead of
full_name (Rafael Wysocki, Rob Herring).
- Update the devfreq framework to fix and clean up a few minor
issues (Chanwoo Choi, Rob Herring).
- Extend diagnostics in the generic power domains (genpd) framework
and clean it up slightly (Thara Gopinath, Rob Herring).
- Fix and clean up a couple of issues in the operating performance
points (OPP) framework (Viresh Kumar, Waldemar Rymarkiewicz).
- Add support for RV1108 to the rockchip-io Adaptive Voltage Scaling
(AVS) driver (David Wu).
- Fix the usage of notifiers in CPU power management on some
platforms (Alex Shi).
- Update the pm-graph system suspend/hibernation and boot profiling
utility (Todd Brandt).
- Make it possible to run the cpupower utility without CPU0 (Prarit
Bhargava).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=mAiV
-----END PGP SIGNATURE-----
Merge tag 'pm-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"This time (again) cpufreq gets the majority of changes which mostly
are driver updates (including a major consolidation of intel_pstate),
some schedutil governor modifications and core cleanups.
There also are some changes in the system suspend area, mostly related
to diagnostics and debug messages plus some renames of things related
to suspend-to-idle. One major change here is that suspend-to-idle is
now going to be preferred over S3 on systems where the ACPI tables
indicate to do so and provide requsite support (the Low Power Idle S0
_DSM in particular). The system sleep documentation and the tools
related to it are updated too.
The rest is a few cpuidle changes (nothing major), devfreq updates,
generic power domains (genpd) framework updates and a few assorted
modifications elsewhere.
Specifics:
- Drop the P-state selection algorithm based on a PID controller from
intel_pstate and make it use the same P-state selection method
(based on the CPU load) for all types of systems in the active mode
(Rafael Wysocki, Srinivas Pandruvada).
- Rework the cpufreq core and governors to make it possible to take
cross-CPU utilization updates into account and modify the schedutil
governor to actually do so (Viresh Kumar).
- Clean up the handling of transition latency information in the
cpufreq core and untangle it from the information on which drivers
cannot do dynamic frequency switching (Viresh Kumar).
- Add support for new SoCs (MT2701/MT7623 and MT7622) to the mediatek
cpufreq driver and update its DT bindings (Sean Wang).
- Modify the cpufreq dt-platdev driver to autimatically create
cpufreq devices for the new (v2) Operating Performance Points (OPP)
DT bindings and update its whitelist of supported systems (Viresh
Kumar, Shubhrajyoti Datta, Marc Gonzalez, Khiem Nguyen, Finley
Xiao).
- Add support for Ux500 to the cpufreq-dt driver and drop the
obsolete dbx500 cpufreq driver (Linus Walleij, Arnd Bergmann).
- Add new SoC (R8A7795) support to the cpufreq rcar driver (Khiem
Nguyen).
- Fix and clean up assorted issues in the cpufreq drivers and core
(Arvind Yadav, Christophe Jaillet, Colin Ian King, Gustavo Silva,
Julia Lawall, Leonard Crestez, Rob Herring, Sudeep Holla).
- Update the IO-wait boost handling in the schedutil governor to make
it less aggressive (Joel Fernandes).
- Rework system suspend diagnostics to make it print fewer messages
to the kernel log by default, add a sysfs knob to allow more
suspend-related messages to be printed and add Low Power S0 Idle
constraints checks to the ACPI suspend-to-idle code (Rafael
Wysocki, Srinivas Pandruvada).
- Prefer suspend-to-idle over S3 on ACPI-based systems with the
ACPI_FADT_LOW_POWER_S0 flag set and the Low Power Idle S0 _DSM
interface present in the ACPI tables (Rafael Wysocki).
- Update documentation related to system sleep and rename a number of
items in the code to make it cleare that they are related to
suspend-to-idle (Rafael Wysocki).
- Export a variable allowing device drivers to check the target
system sleep state from the core system suspend code (Florian
Fainelli).
- Clean up the cpuidle subsystem to handle the polling state on x86
in a more straightforward way and to use %pOF instead of full_name
(Rafael Wysocki, Rob Herring).
- Update the devfreq framework to fix and clean up a few minor issues
(Chanwoo Choi, Rob Herring).
- Extend diagnostics in the generic power domains (genpd) framework
and clean it up slightly (Thara Gopinath, Rob Herring).
- Fix and clean up a couple of issues in the operating performance
points (OPP) framework (Viresh Kumar, Waldemar Rymarkiewicz).
- Add support for RV1108 to the rockchip-io Adaptive Voltage Scaling
(AVS) driver (David Wu).
- Fix the usage of notifiers in CPU power management on some
platforms (Alex Shi).
- Update the pm-graph system suspend/hibernation and boot profiling
utility (Todd Brandt).
- Make it possible to run the cpupower utility without CPU0 (Prarit
Bhargava)"
* tag 'pm-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (87 commits)
cpuidle: Make drivers initialize polling state
cpuidle: Move polling state initialization code to separate file
cpuidle: Eliminate the CPUIDLE_DRIVER_STATE_START symbol
cpufreq: imx6q: Fix imx6sx low frequency support
cpufreq: speedstep-lib: make several arrays static, makes code smaller
PM: docs: Delete the obsolete states.txt document
PM: docs: Describe high-level PM strategies and sleep states
PM / devfreq: Fix memory leak when fail to register device
PM / devfreq: Add dependency on PM_OPP
PM / devfreq: Move private devfreq_update_stats() into devfreq
PM / devfreq: Convert to using %pOF instead of full_name
PM / AVS: rockchip-io: add io selectors and supplies for RV1108
cpufreq: ti: Fix 'of_node_put' being called twice in error handling path
cpufreq: dt-platdev: Drop few entries from whitelist
cpufreq: dt-platdev: Automatically create cpufreq device with OPP v2
ARM: ux500: don't select CPUFREQ_DT
cpuidle: Convert to using %pOF instead of full_name
cpufreq: Convert to using %pOF instead of full_name
PM / Domains: Convert to using %pOF instead of full_name
cpufreq: Cap the default transition delay value to 10 ms
...
Core changes:
- Decision to wrap the sleep mode of the Spreadtrum and in the future
others into a specially tagged state. The generic DT bindings and the
new Spreadtrum driver conforms to this. Others should be moved over
if possible.
New drivers:
- New driver for Spreadtrum SoCs especially the SC9860 SoC.
- New driver for Storlink/Cortina Gemini 3512 and 3516 SoCs.
New subdrivers:
- Intel Denverton subdriver.
- Intel Cannon Lake subdriver.
- Intel Lewisburg subdriver.
- Allwinner sunxi: R40 subdriver for A10.
- Socionext uniphier PXs3 subdriver.
- Rockchip RK3128 subdriver.
- Renesas SH-PFC R8A77995 subdriver.
Miscellaneous:
- Qualcomm APQ8064 can handle general purpose clock muxing.
- Mediatek MT7623 PCIe mux data fixed up.
- Intel GPIO IRQs are disabled during suspend.
- Several fixes and addtions to Renesas r8a7796.
- Qualcomm SPMI GPIO supports dtest route and LV/MV subtype.
- Input schmitt trigger support in Rockchip RV1108.
- Aspeed G4 and G5 USB host/device pin control control added.
- Qualcomm IPQ4019 has matured with a few missing pin groups and
control bits put in place.
- Lots of constification, this is the latest in cocinelle fixes.
-----BEGIN PGP SIGNATURE-----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=GkNo
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the big bulk of pin control changes for the v4.14 kernel.
There are just a few bigger changes (new drivers mostly) and then a
lot of small patches all over the place.
Core changes:
- Decision to wrap the sleep mode of the Spreadtrum and in the future
others into a specially tagged state. The generic DT bindings and
the new Spreadtrum driver conforms to this. Others should be moved
over if possible.
New drivers:
- Spreadtrum SoCs especially the SC9860 SoC.
- Storlink/Cortina Gemini 3512 and 3516 SoCs.
New subdrivers:
- Intel Denverton subdriver.
- Intel Cannon Lake subdriver.
- Intel Lewisburg subdriver.
- Allwinner sunxi: R40 subdriver for A10.
- Socionext uniphier PXs3 subdriver.
- Rockchip RK3128 subdriver.
- Renesas SH-PFC R8A77995 subdriver.
Miscellaneous:
- Qualcomm APQ8064 can handle general purpose clock muxing.
- Mediatek MT7623 PCIe mux data fixed up.
- Intel GPIO IRQs are disabled during suspend.
- Several fixes and addtions to Renesas r8a7796.
- Qualcomm SPMI GPIO supports dtest route and LV/MV subtype.
- Input schmitt trigger support in Rockchip RV1108.
- Aspeed G4 and G5 USB host/device pin control control added.
- Qualcomm IPQ4019 has matured with a few missing pin groups and
control bits put in place.
- Lots of constification, this is the latest in cocinelle fixes"
* tag 'pinctrl-v4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (147 commits)
Revert "pinctrl: sunxi: Don't enforce bias disable (for now)"
pinctrl: uniphier: fix members of rmii group for Pro4
pinctrl: Delete an error message
pinctrl: core: Delete an error message
pinctrl: intel: Read back TX buffer state
pinctrl: rockchip: Add rv1108 recalculated iomux support
pinctrl: intel: Decrease indentation in intel_gpio_set()
pinctrl: rza1: Remove suffix from gpiochip label
pinctrl: qcom: spmi-gpio: Correct power_source range check
pinctrl: freescale: make mxs_regs const
pinctrl: aspeed: Rework strap register write logic for the AST2500
pinctrl: rza1: off by one in rza1_parse_gpiochip()
pinctrl: qcom: General Purpose clocks for apq8064
pinctrl: sprd: Add Spreadtrum pin control driver
dt-bindings: pinctrl: Add DT bindings for Spreadtrum SC9860
pinctrl: Add sleep related state to indicate sleep related configs
pinctrl: mediatek: update PCIe mux data for MT7623
pinctrl: intel: Add Intel Lewisburg GPIO support
pinctrl: intel: Add Intel Cannon Lake PCH-H pin controller support
pinctrl: aspeed: Fix ast2500 strap register write logic
...
Here is the big char/misc driver update for 4.14-rc1.
Lots of different stuff in here, it's been an active development cycle
for some reason. Highlights are:
- updated binder driver, this brings binder up to date with what
shipped in the Android O release, plus some more changes that
happened since then that are in the Android development trees.
- coresight updates and fixes
- mux driver file renames to be a bit "nicer"
- intel_th driver updates
- normal set of hyper-v updates and changes
- small fpga subsystem and driver updates
- lots of const code changes all over the driver trees
- extcon driver updates
- fmc driver subsystem upadates
- w1 subsystem minor reworks and new features and drivers added
- spmi driver updates
Plus a smattering of other minor driver updates and fixes.
All of these have been in linux-next with no reported issues for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWa1+Ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yl26wCgquufNylfhxr65NbJrovduJYzRnUAniCivXg8
bePIh/JI5WxWoHK+wEbY
=hYWx
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big char/misc driver update for 4.14-rc1.
Lots of different stuff in here, it's been an active development cycle
for some reason. Highlights are:
- updated binder driver, this brings binder up to date with what
shipped in the Android O release, plus some more changes that
happened since then that are in the Android development trees.
- coresight updates and fixes
- mux driver file renames to be a bit "nicer"
- intel_th driver updates
- normal set of hyper-v updates and changes
- small fpga subsystem and driver updates
- lots of const code changes all over the driver trees
- extcon driver updates
- fmc driver subsystem upadates
- w1 subsystem minor reworks and new features and drivers added
- spmi driver updates
Plus a smattering of other minor driver updates and fixes.
All of these have been in linux-next with no reported issues for a
while"
* tag 'char-misc-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (244 commits)
ANDROID: binder: don't queue async transactions to thread.
ANDROID: binder: don't enqueue death notifications to thread todo.
ANDROID: binder: Don't BUG_ON(!spin_is_locked()).
ANDROID: binder: Add BINDER_GET_NODE_DEBUG_INFO ioctl
ANDROID: binder: push new transactions to waiting threads.
ANDROID: binder: remove proc waitqueue
android: binder: Add page usage in binder stats
android: binder: fixup crash introduced by moving buffer hdr
drivers: w1: add hwmon temp support for w1_therm
drivers: w1: refactor w1_slave_show to make the temp reading functionality separate
drivers: w1: add hwmon support structures
eeprom: idt_89hpesx: Support both ACPI and OF probing
mcb: Fix an error handling path in 'chameleon_parse_cells()'
MCB: add support for SC31 to mcb-lpc
mux: make device_type const
char: virtio: constify attribute_group structures.
Documentation/ABI: document the nvmem sysfs files
lkdtm: fix spelling mistake: "incremeted" -> "incremented"
perf: cs-etm: Fix ETMv4 CONFIGR entry in perf.data file
nvmem: include linux/err.h from header
...
Pull irq updates from Thomas Gleixner:
"The interrupt subsystem delivers this time:
- Refactoring of the GIC-V3 driver to prepare for the GIC-V4 support
- Initial GIC-V4 support
- Consolidation of the FSL MSI support
- Utilize the effective affinity interface in various ARM irqchip
drivers
- Yet another interrupt chip driver (UniPhier AIDET)
- Bulk conversion of the irq chip driver to use %pOF
- The usual small fixes and improvements all over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (77 commits)
irqchip/ls-scfg-msi: Add MSI affinity support
irqchip/ls-scfg-msi: Add LS1043a v1.1 MSI support
irqchip/ls-scfg-msi: Add LS1046a MSI support
arm64: dts: ls1046a: Add MSI dts node
arm64: dts: ls1043a: Share all MSIs
arm: dts: ls1021a: Share all MSIs
arm64: dts: ls1043a: Fix typo of MSI compatible string
arm: dts: ls1021a: Fix typo of MSI compatible string
irqchip/ls-scfg-msi: Fix typo of MSI compatible strings
irqchip/irq-bcm7120-l2: Use correct I/O accessors for irq_fwd_mask
irqchip/mmp: Make mmp_intc_conf const
irqchip/gic: Make irq_chip const
irqchip/gic-v3: Advertise GICv4 support to KVM
irqchip/gic-v4: Enable low-level GICv4 operations
irqchip/gic-v4: Add some basic documentation
irqchip/gic-v4: Add VLPI configuration interface
irqchip/gic-v4: Add VPE command interface
irqchip/gic-v4: Add per-VM VPE domain creation
irqchip/gic-v3-its: Set implementation defined bit to enable VLPIs
irqchip/gic-v3-its: Allow doorbell interrupts to be injected/cleared
...
* pm-cpufreq: (33 commits)
cpufreq: imx6q: Fix imx6sx low frequency support
cpufreq: speedstep-lib: make several arrays static, makes code smaller
cpufreq: ti: Fix 'of_node_put' being called twice in error handling path
cpufreq: dt-platdev: Drop few entries from whitelist
cpufreq: dt-platdev: Automatically create cpufreq device with OPP v2
ARM: ux500: don't select CPUFREQ_DT
cpufreq: Convert to using %pOF instead of full_name
cpufreq: Cap the default transition delay value to 10 ms
cpufreq: dbx500: Delete obsolete driver
mfd: db8500-prcmu: Get rid of cpufreq dependency
cpufreq: enable the DT cpufreq driver on the Ux500
cpufreq: Loongson2: constify platform_device_id
cpufreq: dt: Add r8a7796 support to to use generic cpufreq driver
cpufreq: remove setting of policy->cpu in policy->cpus during init
cpufreq: mediatek: add support of cpufreq to MT7622 SoC
cpufreq: mediatek: add cleanups with the more generic naming
cpufreq: rcar: Add support for R8A7795 SoC
cpufreq: dt: Add rk3328 compatible to use generic cpufreq driver
cpufreq: s5pv210: add missing of_node_put()
cpufreq: Allow dynamic switching with CPUFREQ_ETERNAL latency
...
This is a revert of the EMAC bindings. The discussion has not settled down
yet on a proper representation of the PHY, and therefore we cannot commit
to a binding yet
-----BEGIN PGP SIGNATURE-----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=0xy6
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.13-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner fixes for 4.13, take 3
This is a revert of the EMAC bindings. The discussion has not settled down
yet on a proper representation of the PHY, and therefore we cannot commit
to a binding yet
* tag 'sunxi-fixes-for-4.13-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm: dts: sunxi: Revert EMAC changes
arm64: dts: allwinner: Revert EMAC changes
dt-bindings: net: Revert sun8i dwmac binding
arm64: allwinner: h5: fix pinctrl IRQs
arm64: allwinner: a64: sopine: add missing ethernet0 alias
arm64: allwinner: a64: pine64: add missing ethernet0 alias
arm64: allwinner: a64: bananapi-m64: add missing ethernet0 alias
Signed-off-by: Olof Johansson <olof@lixom.net>
In order to maximize the use of MSI, a PCIe controller will share
all MSI controllers. The patch changes msi-parent to refer to all
MSI controller dts nodes.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
"1" should be replaced by "l". This is a typo.
The patch is to fix it.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
One new board, and a revert of a patch relying on a binding not stable
enough so that we can commit to it.
-----BEGIN PGP SIGNATURE-----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=jgbH
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.14-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner DT changes for 4.14, take 3
One new board, and a revert of a patch relying on a binding not stable
enough so that we can commit to it.
* tag 'sunxi-dt-for-4.14-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
Revert "ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Beelink X2"
ARM: sun8i: a83t: Add device tree for Sinovoip Bananapi BPI-M3
Signed-off-by: Olof Johansson <olof@lixom.net>
AT91SAM9G45 has an AC97 controller, but it is not described in the dts
file.
This patch adds AC97 node in device tree.
Signed-off-by: Dmitry Rezvanov <dmitry.rezvanov@yandex.ru>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This is a revert of the EMAC bindings. The discussion has not settled down
yet on a proper representation of the PHY, and therefore we cannot commit
to a binding yet
-----BEGIN PGP SIGNATURE-----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=0xy6
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.13-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into fixes
Allwinner fixes for 4.13, take 3
This is a revert of the EMAC bindings. The discussion has not settled down
yet on a proper representation of the PHY, and therefore we cannot commit
to a binding yet
* tag 'sunxi-fixes-for-4.13-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm: dts: sunxi: Revert EMAC changes
arm64: dts: allwinner: Revert EMAC changes
dt-bindings: net: Revert sun8i dwmac binding
Signed-off-by: Olof Johansson <olof@lixom.net>
Add pinctrl groups of ethenet phy mode, such as "ether_rgmii", "ether_rmii",
and "ether_mii".
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since the discussion is not settled yet for the EMAC, and that the release
in getting really close, let's revert the changes for now, and we'll
reintroduce them later.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This reverts commit ddb56254ae. The EMAC
bindings have not stabilized yet, so we can't commit to keeping them
stable.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch solves the following error:
arch/arm/boot/dts/rk3228-evb.dtb: ERROR (phandle_references): Reference to non-existent node or label "phy0"
Fixess db40f15b53 ("ARM: dts: rk3228-evb: Enable the integrated PHY for gmac")
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the as3645a flash controller to the DT source.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
(usb, operating points, spi, pwm, adc, watchdog, i2c and devices for
its evb).
RK3228/3229 gets iommu and spi nodes. Similar to the rk3288 which
also gets some more iommu nodes as well as getting converted to 64
bit addresses due to wanting to address more than 4GB of memory
via LPAE.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlmdoA4QHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgeBtB/9oM4MmVRJ0YX7hk4NuU9c4HHdvCW0f1rJe
Q6rE6dP7fW3J27d6PuySVWzvIBmD+3xVA2t0dDm85DIP8f1DFz3vyNhkEsu1VG89
MULTektihczugCy+sh3iHILs4fLXJ8QUjCKJWOcWmZHOaXNXXjJIVjC97m5F4ZAj
KVOYXNnCKdaHYIeP0lkjStL8Z9Ua7svkjfgsSPTGTSJQQ+bGcd/8JnmlkzjfHWLw
qNz6M7FPoJ1rAffskr1At27oRs7UAVSKNAejl8DWKvLXml6NQPRRRu99sLLanxII
3b6LsC6Vwea4a1Rjwx0LZWdDUtB1W34/ZIEw4JceK/i6HfV5K2Oi
=di6U
-----END PGP SIGNATURE-----
Merge tag 'v4.14-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "second round of Rockchip dts32 changes for 4.14" from Heiko Stübner:
A lot of attention for the rv1108 soc targetted at media-processing
(usb, operating points, spi, pwm, adc, watchdog, i2c and devices for
its evb).
RK3228/3229 gets iommu and spi nodes. Similar to the rk3288 which
also gets some more iommu nodes as well as getting converted to 64
bit addresses due to wanting to address more than 4GB of memory
via LPAE.
* tag 'v4.14-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: enable usb for rv1108-evb
ARM: dts: rockchip: add usb nodes for rv1108 SoCs
dt-bindings: update grf-binding for rv1108 SoCs
ARM: dts: rockchip: add cpu power supply for rv1108 evb
ARM: dts: rockchip: add cpu opp table for rv1108
ARM: dts: rockchip: add rk322x iommu nodes
ARM: dts: rockchip: add accelerometer bma250e dt node for rv1108 evb
ARM: dts: rockchip: add pmic rk805 dt node for rv1108 evb
ARM: dts: rockchip: add pwm backlight for rv1108 evb
ARM: dts: rockchip: add pwm dt nodes for rv1108
ARM: dts: rockchip: add spi dt node for rv1108
ARM: dts: rockchip: add saradc support for rv1108
ARM: dts: rockchip: add watchdog dt node for rv1108
ARM: dts: rockchip: add i2c dt nodes for rv1108
clk: rockchip: fix up indentation of some RV1108 clock-ids
clk: rockchip: rename the clk id for HCLK_I2S1_2CH
clk: rockchip: add more clk ids for rv1108
ARM: dts: rockchip: add more iommu nodes on rk3288
ARM: dts: rockchip: convert rk3288 device tree files to 64 bits
ARM: dts: rockchip: add spi node and spi pinctrl on rk3228/rk3229
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- fix to expose the full flash windows on ast2400.
-----BEGIN PGP SIGNATURE-----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=q9Dz
-----END PGP SIGNATURE-----
Merge tag 'aspeed-4.14-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into next/dt
Pull "Aspeed devicetree updates for 4.14" from Joel Stanley:
- fix to expose the full flash windows on ast2400.
* tag 'aspeed-4.14-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
ARM: dts: aspeed-g4: fix AHB window size of the SMC controllers
Fix PCI bus dtc warnings.
-----BEGIN PGP SIGNATURE-----
iQIcBAABCAAGBQJZna4DAAoJEME3ZuaGi4PXsWoP/1IwPnPEunNnLjyM0KB//VHF
8HXQ0sQfJHi9Zb10nnlnWDJRyuam9qewqFjZihy4IsmeKmC5eIwBZT4xVZ6JP26D
XXSDC7sxKbo9eGy795NrJv2SC4Dy6y77R2W4bMJOG/L7t4IyIXrkCMaW2Wp3W2eh
5+/Ism6tBhH6MXgJ1lEW2kV/hwSqQLMclM/WrFcJcONQ4UPbdGsjfnDadjCl7TCo
LLGmde2HtcjPobiL7BlsR815JwFkUrIo9aityixDOvlkVLoKDF+Td94TMbirifqU
eXiXgvxZPXvZQbva5999zRXkhnX/bdenFCdvc+pxsy0geDTKSfLOedrzwMl5ORFc
ZqmNXS9HovVzyeR5g/YEMI7Cbjck/f/wzk3QUzUdn2EDx1/3AVCOdhTsyICGvvpC
KWHtt71KOIlWHN34IFtx3nzqcsOyQFKOrFIwR1oO4z7W+hBSXsXwtYaRkTNNTm5e
A2haGjGRPmBwDGU47auLht0seJjmiwwB5r+XB6rOcQk9uGRNN3Hi3nqyzbSTJW7w
NBZH5r7egMML44LVx/m7ThINvEjJbY7/OHyNKKdJabYx9ZxXy2Gbu2rpVtwcIdSt
Vl4Lhc0d98Fys4RDnV4ShyTJX/4Zb6ecoyYpkCEkBdieyswj4VEXXURAaOsSBmq4
hZJviCJDujD44Gdt4PqR
=6neG
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Pull "Samsung DTS ARM changes for v4.14, part 2" from Krzysztof Kozłowski:
Fix PCI bus dtc warnings.
* tag 'samsung-dt-4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: fix PCI bus dtc warnings
CEC support was added for Exynos5 in 4.13, but for the Odroids we need to set
'needs-hpd' as well since CEC is disabled when there is no HDMI hotplug signal,
just as for the exynos4 Odroid-U3.
This is due to the level-shifter that is disabled when there is no HPD, thus
blocking the CEC signal as well. Same close-but-no-cigar board design as the
Odroid-U3.
Tested with my Odroid XU4.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Rockchip's rv1108-evb board has one usb otg controller and one usb
host controller, each usb controller connect with one usb-phy port
through UTMI+ interface. This patch enables them to support usb on
rv1108-evb board.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds usb otg/host controllers and phys nodes for RV1108 SoCs.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The window of the Aspeed AST2400 SMC Controllers to map chips on the
AHB Bus has a 256MB size. The full window range is
[ 0x20000000 - 0x2FFFFFFF ] for the FMC controller
[ 0x30000000 - 0x3FFFFFFF ] for the SPI controller
This change requires CONFIG_VMSPLIT_2G to be set.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The cpu is powered by regulator vdd_core on RV1108 evalution
board. Add it to the cpu dt node.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add cpu opp table for rv1108 to support frequency
from 408MHZ to 1008MHZ.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
- Remove earlycon
- Use C pre-processor
- Add fpga full region
- Add ethernet-phy as device-type
- Add adv7511 nodes to zc70x
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlmaypgACgkQykllyylKDCEpkACgkWAijGmJRMDb5HvrH7npUkwz
QRkAnjQCUrRIO5RbuXob5fIZurV2kMwn
=7Ggj
-----END PGP SIGNATURE-----
Merge tag 'zynq-dt-for-4.14' of https://github.com/Xilinx/linux-xlnx into next/dt
Pull "arm: Xilinx Zynq DT fixes for v4.14" from Michal Simek:
- Remove earlycon
- Use C pre-processor
- Add fpga full region
- Add ethernet-phy as device-type
- Add adv7511 nodes to zc70x
* tag 'zynq-dt-for-4.14' of https://github.com/Xilinx/linux-xlnx:
arm: zynq: Remove earlycon from bootargs
arm: zynq: Use C pre-processor for includes in dts
arm: zynq: Label whole PL part as fpga_full region
arm: zynq: Add device-type property for zynq ethernet phy nodes
arm: zynq: Add adv7511 on i2c bus for zc70x
This adds the operating points to the Ux500 device tree and
deletes the old special-purpose cpufreq node, as we can now
use the generic DT cpufreq driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
