and convert PXA-based devices to gpio_pwdown where possible.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
So, again against latest pxa-linux-2.6/devel, with the following
changes:
* Move to __raw_readl/__raw_writel for FPGA/CPLD register access
* Change Toppoly LCD config to be selectable at run time rather than
compile time.
* Remove currently unused irq device suspend/resume functions.
* Strip out unnecessary/duplicated #includes.
* Some code style cleanups.
Balloon3 (http://balloonboard.org/) base machine support
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Added support for the Iskratel XCEP single board computer, embedded in
instruments used in particle accelerators.
The patch contains the platform specific code, Makefile and Kconfig
changes for platform arm-pxa.
Signed-off-by: Aleš Bardorfer <ales.bardorfer@i-tech.si>
Signed-off-by: Michael Abbott <michael.abbott@diamond.ac.uk>
Signed-off-by: Matej Kenda <matej.kenda@i-tech.si>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Instead of directly registering an lcd_device, use the platform_lcd driver.
This fixes a broken build in case CONFIG_LCD_CLASS_DEVICE is not enabled.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Ben Dooks <ben-linux-arm@fluff.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This 'problem' actually cant cause a failure of the driver, but it's always
better to be correct.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch adds support for PCMCIA socket found in Palm Tungsten|C.
There is Prism3 based WiFi card hardwired to that socket.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch adds basic support for Palm Tungsten|C handheld.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch adds support for NAND chip found in PalmTX handheld. Support
is implemented through the gen_nand driver.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
v2 changes:
- use gpio_to_irq instead of IRQ_GPIO
- check gpio_direction_output return value to be on the safe side :)
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch configures the MFP pads for UART1, UART2, UART3 for the
Toradex Colibri PXA320 module. Previously they were just not
configured resulting in just the first UART working because it was the
only one that was configured by the bootloader (Toradex EBOOT in our
case).
This patch is against vanilla 2.6.30 and has been tested with the
Toradex Orchid carrier board (all three UARTs were functional).
Signed-off-by: Alex Roman <alex.roman@gmail.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
NAND feature will be enabled when the appropriate config option is set.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Several boards use always the same pattern with pxamci :
request gpio, request irq for that gpio to detect MMC card
insertion, request gpio for read-only mode detection, etc
...
Now that pxamci provides platform_data to describe simple
gpio management of the MMC external controls, use it.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: rpurdie@rpsys.net
Cc: drwyrm@gmail.com
Cc: sakoman@gmail.com
Cc: marek.vasut@gmail.com
Cc: s.hauer@pengutronix.de
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The MMC block needs 3 external datas to work :
- is the MMC card put in "read-only mode" ?
- is a MMC card inserted or removed ?
- enable power towards the MMC card
Several platforms provide these controls through
gpios. Expand the platform_data to request and use these
gpios is set up by board code.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Pierre.Ossman <pierre@ossman.eu>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Add some debug information for PXA DMA :
- descriptors queued
- channels state
- global state
--
Since V1: reverted to old register access (no more dma_readl() or dma_writel()).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Reduce loop for dma irq handler callbacks to the minimum
required.
Since V1: included suggestion from Nicolas Pitre to improve
even further the loop.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Merge zylonite_defconfig and littleton_defconfig into pxa3xx_defconfig.
Since they're similar platform and servicing for same SoC family.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
PXA I2C module is also used in Marvell PXA168 and PXA910 series.
Update the module dependancy of PXA I2C.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Add priority registers and new registers of pxa935.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
CPU id is changed in Marvell chip. So update the code in cpu_is_xsc3().
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
PXA93x/950 has additional 64 GPIOs, each is a secondary interrupt
source for IRQ_GPIO_2_x, extend PXA_GPIO_IRQ_{BASE,NUM}.
PXA93x/950 specific IRQ definitions are added as well.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Add and initialize the mfp setting of pxa935 chip.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
There is currently an uncovered case for MFP configuration on PXAs which
is selected by setting the PULL_SEL bit but none of the PULL{UP,DOWN}_EN
bits. This case is needed to explicitly let pins float, even if the
selected alternate function would default to a configuration with a pull
resistor enabled.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Its removal was omitted when all its uses were removed in 8c3abc7d...
"[ARM] pxa: convert to clkdev and match clocks by struct device where possible"
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Andy Whitcroft reported an oops in aoe triggered by use of an
incorrectly initialised request_queue object:
[ 2645.959090] kobject '<NULL>' (ffff880059ca22c0): tried to add
an uninitialized object, something is seriously wrong.
[ 2645.959104] Pid: 6, comm: events/0 Not tainted 2.6.31-5-generic #24-Ubuntu
[ 2645.959107] Call Trace:
[ 2645.959139] [<ffffffff8126ca2f>] kobject_add+0x5f/0x70
[ 2645.959151] [<ffffffff8125b4ab>] blk_register_queue+0x8b/0xf0
[ 2645.959155] [<ffffffff8126043f>] add_disk+0x8f/0x160
[ 2645.959161] [<ffffffffa01673c4>] aoeblk_gdalloc+0x164/0x1c0 [aoe]
The request queue of an aoe device is not used but can be allocated in
code that does not sleep.
Bruno bisected this regression down to
cd43e26f07
block: Expose stacked device queues in sysfs
"This seems to generate /sys/block/$device/queue and its contents for
everyone who is using queues, not just for those queues that have a
non-NULL queue->request_fn."
Addresses http://bugs.launchpad.net/bugs/410198
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13942
Note that embedding a queue inside another object has always been
an illegal construct, since the queues are reference counted and
must persist until the last reference is dropped. So aoe was
always buggy in this respect (Jens).
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Cc: Andy Whitcroft <apw@canonical.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Bruno Premont <bonbons@linux-vserver.org>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Reinette Chatre reports a frozen system (with blinking keyboard LEDs)
when switching from graphics mode to the text console, or when
suspending (which does the same thing). With netconsole, the oops
turned out to be
BUG: unable to handle kernel NULL pointer dereference at 0000000000000084
IP: [<ffffffffa03ecaab>] i915_driver_irq_handler+0x26b/0xd20 [i915]
and it's due to the i915_gem.c code doing drm_irq_uninstall() after
having done i915_gem_idle(). And the i915_gem_idle() path will do
i915_gem_idle() ->
i915_gem_cleanup_ringbuffer() ->
i915_gem_cleanup_hws() ->
dev_priv->hw_status_page = NULL;
but if an i915 interrupt comes in after this stage, it may want to
access that hw_status_page, and gets the above NULL pointer dereference.
And since the NULL pointer dereference happens from within an interrupt,
and with the screen still in graphics mode, the common end result is
simply a silently hung machine.
Fix it by simply uninstalling the irq handler before idling rather than
after. Fixes
http://bugzilla.kernel.org/show_bug.cgi?id=13819
Reported-and-tested-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
eDP is exclusive connector too, and add missing crtc_mask
setting for TV.
This fixes
http://bugzilla.kernel.org/show_bug.cgi?id=14139
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Reported-and-tested-by: Carlos R. Mafra <crmafra2@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
