As with registers and tables, use GENMASK and the bitfield accessors
consistently for queue fields, to save some lines and ease maintenance
a little. This now leaves everything in a nice state where all named
field definitions expect to be used with bitfield accessors (although
since single-bit fields can still be used directly we leave some of
those uses as-is to avoid unnecessary churn), while the few remaining
*_MASK definitions apply exclusively to in-place values.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
As with registers, use GENMASK and the bitfield accessors consistently
for table fields, to save some lines and ease maintenance a little. This
also catches a subtle off-by-one wherein bit 5 of CD.T0SZ was missing.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The FIELD_{GET,PREP} accessors provided by linux/bitfield.h allow us to
define multi-bit register fields solely in terms of their bit positions
via GENMASK(), without needing explicit *_SHIFT and *_MASK definitions.
As well as the immediate reduction in lines of code, this avoids the
awkwardness of values sometimes being pre-shifted and sometimes not,
which means we can factor out some common values like memory attributes.
Furthermore, it also makes it trivial to verify the definitions against
the architecture spec, on which note let's also fix up a few field names
to properly match the current release (IHI0070B).
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Before trying to add the SMMUv3.1 support for 52-bit addresses, make
things bearable by cleaning up the various address mask definitions to
use GENMASK_ULL() consistently. The fact that doing so reveals (and
fixes) a latent off-by-one in Q_BASE_ADDR_MASK only goes to show what a
jolly good idea it is...
Tested-by: Nate Watterson <nwatters@codeaurora.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Currently, the arm-smmu-v3 driver expects to allocate MSIs for all SMMUs
with FEAT_MSI set. This results in unwarranted "failed to allocate MSIs"
warnings being printed on systems where FW was either deliberately
configured to force the use of SMMU wired interrupts -or- is altogether
incapable of describing SMMU MSI topology (ACPI IORT prior to rev.C).
Remedy this by checking msi_domain before attempting to allocate SMMU
MSIs.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Nate Watterson <nwatters@codeaurora.org>
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
It is annoyingly non-obvious when DMA transactions silently go missing
due to undetected SMMU faults. Help skip the first few debugging steps
in those situations by making it clear when we have neither wired IRQs
nor MSIs with which to raise error conditions.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now that no more drivers rely on arbitrary early initialisation via an
of_iommu_init_fn hook, let's clean up the redundant remnants. The
IOMMU_OF_DECLARE() macro needs to remain for now, as the probe-deferral
mechanism has no other nice way to detect built-in drivers before they
have registered themselves, such that it can make the right decision.
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
For PCI devices behind an aliasing PCIe-to-PCI/X bridge, the bridge
alias to DevFn 0.0 on the subordinate bus may match the original RID of
the device, resulting in the same SID being present in the device's
fwspec twice. This causes trouble later in arm_smmu_write_strtab_ent()
when we wind up visiting the STE a second time and find it already live.
Avoid the issue by giving arm_smmu_install_ste_for_dev() the cleverness
to skip over duplicates. It seems mildly counterintuitive compared to
preventing the duplicates from existing in the first place, but since
the DT and ACPI probe paths build their fwspecs differently, this is
actually the cleanest and most self-contained way to deal with it.
Cc: <stable@vger.kernel.org>
Fixes: 8f78515425 ("iommu/arm-smmu: Implement of_xlate() for SMMUv3")
Reported-by: Tomasz Nowicki <tomasz.nowicki@caviumnetworks.com>
Tested-by: Tomasz Nowicki <Tomasz.Nowicki@cavium.com>
Tested-by: Jayachandran C. <jnair@caviumnetworks.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Kasan reports a double free when finalise_stage_fn fails: the io_pgtable
ops are freed by arm_smmu_domain_finalise and then again by
arm_smmu_domain_free. Prevent this by leaving pgtbl_ops empty on failure.
Cc: <stable@vger.kernel.org>
Fixes: 48ec83bcbc ("iommu/arm-smmu: Add initial driver support for ARM SMMUv3 devices")
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
While CMD_SYNC is unlikely to complete immediately such that we never go
round the polling loop, with a lightly-loaded queue it may still do so
long before the delay period is up. If we have no better completion
notifier, use similar logic as we have for SMMUv2 to spin a number of
times before each backoff, so that we have more chance of catching syncs
which complete relatively quickly and avoid delaying unnecessarily.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We have separate (identical) timeout values for polling for a queue to
drain and waiting for an MSI to signal CMD_SYNC completion. In reality,
we only wait for the command queue to drain if we're waiting on a sync,
so just merged these two timeouts into a single constant.
Signed-off-by: Will Deacon <will.deacon@arm.com>
arm_smmu_cmdq_issue_sync is a little unwieldy now that it supports both
MSI and event-based polling, so split it into two functions to make things
easier to follow.
Signed-off-by: Will Deacon <will.deacon@arm.com>
As an IRQ, the CMD_SYNC interrupt is not particularly useful, not least
because we often need to wait for sync completion within someone else's
IRQ handler anyway. However, when the SMMU is both coherent and supports
MSIs, we can have a lot more fun by not using it as an interrupt at all.
Following the example suggested in the architecture and using a write
targeting normal memory, we can let callers wait on a status variable
outside the lock instead of having to stall the entire queue or even
touch MMIO registers. Since multiple sync commands are guaranteed to
complete in order, a simple incrementing sequence count is all we need
to unambiguously support any realistic number of overlapping waiters.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The cmdq-sync interrupt is never going to be particularly useful, since
for stage 1 DMA at least we'll often need to wait for sync completion
within someone else's IRQ handler, thus have to implement polling
anyway. Beyond that, the overhead of taking an interrupt, then still
having to grovel around in the queue to figure out *which* sync command
completed, doesn't seem much more attractive than simple polling either.
Furthermore, if an implementation both has wired interrupts and supports
MSIs, then we don't want to be taking the IRQ unnecessarily if we're
using the MSI write to update memory. Let's just make life simpler by
not even bothering to claim it in the first place.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
CMD_SYNC already has a bit of special treatment here and there, but as
we're about to extend it with more functionality for completing outside
the CMDQ lock, things are going to get rather messy if we keep trying to
cram everything into a single generic command interface. Instead, let's
break out the issuing of CMD_SYNC into its own specific helper where
upcoming changes will have room to breathe.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Slightly confusingly, when reporting a mismatch of the ID register
value, we still refer to the IORT COHACC override flag as the
"dma-coherent property" if we booted with ACPI. Update the message
to be firmware-agnostic in line with SMMUv2.
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reported-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
According to Spec, it is ILLEGAL to set STE.S1STALLD if STALL_MODEL
is not 0b00, which means we should not disable stall mode if stall
or terminate mode is not configuable.
Meanwhile, it is also ILLEGAL when STALL_MODEL==0b10 && CD.S==0 which
means if stall mode is force we should always set CD.S.
As Jean-Philippe's suggestion, this patch introduce a feature bit
ARM_SMMU_FEAT_STALL_FORCE, which means smmu only supports stall force.
Therefore, we can avoid the ILLEGAL setting of STE.S1STALLD.by checking
ARM_SMMU_FEAT_STALL_FORCE.
This patch keeps the ARM_SMMU_FEAT_STALLS as the meaning of stall supported
(force or configuable) to easy to expand the future function, i.e. we can
only use ARM_SMMU_FEAT_STALLS to check whether we should register fault
handle or enable master can_stall, etc to supporte platform SVM.
The feature bit, STE.S1STALLD and CD.S setting will be like:
STALL_MODEL FEATURE S1STALLD CD.S
0b00 ARM_SMMU_FEAT_STALLS 0b1 0b0
0b01 !ARM_SMMU_FEAT_STALLS && !ARM_SMMU_FEAT_STALL_FORCE 0b0 0b0
0b10 ARM_SMMU_FEAT_STALLS && ARM_SMMU_FEAT_STALL_FORCE 0b0 0b1
after apply this patch.
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The SMMUv3 architecture permits caching of data structures deemed to be
"reachable" by the SMU, which includes STEs marked as invalid. When
transitioning an STE to a bypass/fault configuration at init or detach
time, we mistakenly elide the CMDQ_OP_CFGI_STE operation in some cases,
therefore potentially leaving the old STE state cached in the SMMU.
This patch fixes the problem by ensuring that we perform the
CMDQ_OP_CFGI_STE operation irrespective of the validity of the previous
STE.
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reported-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now that the kernel headers have synced with the relevant upstream
ACPICA updates, it's time to clean up the temporary local definitions.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now that the core API issues its own post-unmap TLB sync call, push that
operation out from the io-pgtable-arm internals into the users. For now,
we leave the invalidation implicit in the unmap operation, since none of
the current users would benefit much from any change to that.
CC: Magnus Damm <damm+renesas@opensource.se>
CC: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The shutdown method disables the SMMU to avoid corrupting a new kernel
started with kexec.
Signed-off-by: Nate Watterson <nwatters@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cavium ThunderX2 SMMU doesn't support MSI and also doesn't have unique irq
lines for gerror, eventq and cmdq-sync.
New named irq "combined" is set as a errata workaround, which allows to
share the irq line by register single irq handler for all the interrupts.
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Geetha sowjanya <gakula@caviumnetworks.com>
[will: reworked irq equality checking and added SPI check]
Signed-off-by: Will Deacon <will.deacon@arm.com>
HiSilicon SMMUv3 on Hip06/Hip07 platforms doesn't support CMD_PREFETCH
command. The dt based support for this quirk is already present in the
driver(hisilicon,broken-prefetch-cmd). This adds ACPI support for the
quirk using the IORT smmu model number.
Signed-off-by: shameer <shameerali.kolothum.thodi@huawei.com>
Signed-off-by: hanjun <guohanjun@huawei.com>
[will: rewrote patch]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cavium ThunderX2 SMMU implementation doesn't support page 1 register space
and PAGE0_REGS_ONLY option is enabled as an errata workaround.
This option when turned on, replaces all page 1 offsets used for
EVTQ_PROD/CONS, PRIQ_PROD/CONS register access with page 0 offsets.
SMMU resource size checks are now based on SMMU option PAGE0_REGS_ONLY,
since resource size can be either 64k/128k.
For this, arm_smmu_device_dt_probe/acpi_probe has been moved before
platform_get_resource call, so that SMMU options are set beforehand.
Signed-off-by: Linu Cherian <linu.cherian@cavium.com>
Signed-off-by: Geetha Sowjanya <geethasowjanya.akula@cavium.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The model number is already defined in acpica and we are actually
waiting for the acpi maintainers to include it:
https://github.com/acpica/acpica/commit/d00a4eb86e64
Adding those temporary definitions until the change makes it into
include/acpi/actbl2.h. Once that is done this patch can be reverted.
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
As for SMMUv2, take advantage of io-pgtable's newfound tolerance for
concurrency. Unfortunately in this case the command queue lock remains a
point of serialisation for the unmap path, but there may be a little
more we can do to ameliorate that in future.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Once we remove the serialising spinlock, a potential race opens up for
non-coherent IOMMUs whereby a caller of .map() can be sure that cache
maintenance has been performed on their new PTE, but will have no
guarantee that such maintenance for table entries above it has actually
completed (e.g. if another CPU took an interrupt immediately after
writing the table entry, but before initiating the DMA sync).
Handling this race safely will add some potentially non-trivial overhead
to installing a table entry, which we would much rather avoid on
coherent systems where it will be unnecessary, and where we are stirivng
to minimise latency by removing the locking in the first place.
To that end, let's introduce an explicit notion of cache-coherency to
io-pgtable, such that we will be able to avoid penalising IOMMUs which
know enough to know when they are coherent.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
iommu_device_register returns an error code and, although it currently
never fails, we should check its return value anyway.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
[will: adjusted to follow arm-smmu.c]
Signed-off-by: Will Deacon <will.deacon@arm.com>
of_device_ids are not supposed to change at runtime. All functions
working with of_device_ids provided by <linux/of.h> work with const
of_device_ids. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Waiting for a CMD_SYNC to be processed involves waiting for the command
queue to drain, which can take an awful lot longer than waiting for a
single entry to become available. Consequently, the common timeout value
of 100us has been observed to be too short on some platforms when a
CMD_SYNC is issued into a queued full of TLBI commands.
This patch resolves the issue by using a different (1s) timeout when
waiting for the CMDQ to drain and using a simple back-off mechanism
when polling the cons pointer in the absence of WFE support.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
[will: rewrote commit message and cosmetic changes]
Signed-off-by: Will Deacon <will.deacon@arm.com>
For software initiated address translation, when domain type is
IOMMU_DOMAIN_IDENTITY i.e SMMU is bypassed, mimic HW behavior
i.e return the same IOVA as translated address.
This patch is an extension to Will Deacon's patchset
"Implement SMMU passthrough using the default domain".
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Now that the appropriate ordering is enforced via probe-deferral of
masters in core code, rip it all out and bask in the simplicity.
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
[Sricharan: Rebased on top of ACPI IORT SMMU series]
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
In preparation for allowing the default domain type to be overridden,
this patch adds support for IOMMU_DOMAIN_IDENTITY domains to the
ARM SMMUv3 driver.
An identity domain is created by placing the corresponding stream table
entries into "bypass" mode, which allows transactions to flow through
the SMMU without any translation.
Signed-off-by: Will Deacon <will.deacon@arm.com>
arm_smmu_install_ste_for_dev cannot fail and always returns 0, however
the fact that it returns int means that callers end up implementing
redundant error handling code which complicates STE tracking and is
never executed.
This patch changes the return type of arm_smmu_install_ste_for_dev
to void, to make it explicit that it cannot fail.
Signed-off-by: Will Deacon <will.deacon@arm.com>
The ARM SMMU drivers provide a DOMAIN_ATTR_NESTING domain attribute,
which allows callers of the IOMMU API to request that the page table
for a domain is installed at stage-2, if supported by the hardware.
Since setting this attribute only makes sense for UNMANAGED domains,
this patch returns -ENODEV if the domain_{get,set}_attr operations are
called on other domain types.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now that we're applying the IOMMU API reserved regions to our IOVA
domains, we shouldn't need to privately special-case PCI windows, or
indeed anything else which isn't specific to our iommu-dma layer.
However, since those aren't IOMMU-specific either, rather than start
duplicating code into IOMMU drivers let's transform the existing
function into an iommu_get_resv_regions() helper that they can share.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The introduction of reserved regions has left a couple of rough edges
which we could do with sorting out sooner rather than later. Since we
are not yet addressing the potential dynamic aspect of software-managed
reservations and presenting them at arbitrary fixed addresses, it is
incongruous that we end up displaying hardware vs. software-managed MSI
regions to userspace differently, especially since ARM-based systems may
actually require one or the other, or even potentially both at once,
(which iommu-dma currently has no hope of dealing with at all). Let's
resolve the former user-visible inconsistency ASAP before the ABI has
been baked into a kernel release, in a way that also lays the groundwork
for the latter shortcoming to be addressed by follow-up patches.
For clarity, rename the software-managed type to IOMMU_RESV_SW_MSI, use
IOMMU_RESV_MSI to describe the hardware type, and document everything a
little bit. Since the x86 MSI remapping hardware falls squarely under
this meaning of IOMMU_RESV_MSI, apply that type to their regions as well,
so that we tell the same story to userspace across all platforms.
Secondly, as the various region types require quite different handling,
and it really makes little sense to ever try combining them, convert the
bitfield-esque #defines to a plain enum in the process before anyone
gets the wrong impression.
Fixes: d30ddcaa7b ("iommu: Add a new type field in iommu_resv_region")
Reviewed-by: Eric Auger <eric.auger@redhat.com>
CC: Alex Williamson <alex.williamson@redhat.com>
CC: David Woodhouse <dwmw2@infradead.org>
CC: kvm@vger.kernel.org
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
And also move its remaining functionality to
iommu_device_register() and 'struct iommu_device'.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
In the current arm-smmu-v3 driver, all smmus that support 2-level
stream tables are being forced to use them. This is suboptimal for
smmus that support fewer stream id bits than would fill in a single
second level table. This patch limits the use of 2-level tables to
smmus that both support the feature and whose first level table can
possibly contain more than a single entry.
Signed-off-by: Nate Watterson <nwatters@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
To prevent corruption of the stage-1 context pointer field when
updating STEs, rebuild the entire containing dword instead of
clearing individual fields.
Signed-off-by: Nate Watterson <nwatters@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
IOMMU_CAP_INTR_REMAP has been advertised in arm-smmu(-v3) although
on ARM this property is not attached to the IOMMU but rather is
implemented in the MSI controller (GICv3 ITS).
Now vfio_iommu_type1 checks MSI remapping capability at MSI controller
level, let's correct this.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Tomasz Nowicki <tomasz.nowicki@caviumnetworks.com>
Tested-by: Tomasz Nowicki <tomasz.nowicki@caviumnetworks.com>
Tested-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The get() populates the list with the MSI IOVA reserved window.
At the moment an arbitray MSI IOVA window is set at 0x8000000
of size 1MB. This will allow to report those info in iommu-group
sysfs.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Tomasz Nowicki <tomasz.nowicki@caviumnetworks.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This reverts commit df5e1a0f2a2d779ad467a691203bcbc74d75690e.
Now that proper privileged mappings can be requested via IOMMU_PRIV,
unconditionally overriding the incoming PRIVCFG becomes the wrong thing
to do, so stop it.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In ACPI bases systems, in order to be able to create platform
devices and initialize them for ARM SMMU v3 components, the IORT
kernel implementation requires a set of static functions to be
used by the IORT kernel layer to configure platform devices for
ARM SMMU v3 components.
Add static configuration functions to the IORT kernel layer for
the ARM SMMU v3 components, so that the ARM SMMU v3 driver can
initialize its respective platform device by relying on the IORT
kernel infrastructure and by adding a corresponding ACPI device
early probe section entry.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Tomasz Nowicki <tn@semihalf.com>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Tomasz Nowicki <tn@semihalf.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Current ARM SMMUv3 probe functions intermingle HW and DT probing in the
initialization functions to detect and programme the ARM SMMU v3 driver
features. In order to allow probing the ARM SMMUv3 with other firmwares
than DT, this patch splits the ARM SMMUv3 init functions into DT and HW
specific portions so that other FW interfaces (ie ACPI) can reuse the HW
probing functions and skip the DT portion accordingly.
This patch implements no functional change, only code reshuffling.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Tomasz Nowicki <tn@semihalf.com>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Tomasz Nowicki <tn@semihalf.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Current ARM SMMU v3 driver rely on the struct device.of_node pointer for
device look-up and iommu_ops retrieval.
In preparation for ACPI probing enablement, convert the driver to use
the struct device.fwnode member for device and iommu_ops look-up so that
the driver infrastructure can be used also on systems that do not
associate an of_node pointer to a struct device (eg ACPI), making the
device look-up and iommu_ops retrieval firmware agnostic.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Tomasz Nowicki <tn@semihalf.com>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Tomasz Nowicki <tn@semihalf.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Check for iommu_gather_ops structures that are only stored in the tlb
field of an io_pgtable_cfg structure. The tlb field is of type
const struct iommu_gather_ops *, so iommu_gather_ops structures
having this property can be declared as const.
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We now delay installing our per-bus iommu_ops until we know an SMMU has
successfully probed, as they don't serve much purpose beforehand, and
doing so also avoids fights between multiple IOMMU drivers in a single
kernel. However, the upshot of passing the return value of bus_set_iommu()
back from our probe function is that if there happens to be more than
one SMMUv3 device in a system, the second and subsequent probes will
wind up returning -EBUSY to the driver core and getting torn down again.
Avoid re-setting ops if ours are already installed, so that any genuine
failures stand out.
Fixes: 08d4ca2a67 ("iommu/arm-smmu: Support non-PCI devices with SMMUv3")
CC: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
CC: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
For non-aperture-based IOMMUs, the domain geometry seems to have become
the de-facto way of indicating the input address space size. That is
quite a useful thing from the users' perspective, so let's do the same.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Implement the SMMUv3 equivalent of d346180e70 ("iommu/arm-smmu: Treat
all device transactions as unprivileged"), so that once again those
pesky DMA controllers with their privileged instruction fetches don't
unexpectedly fault in stage 1 domains due to VMSAv8 rules.
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
With the device <-> stream ID relationship suitably abstracted and
of_xlate() hooked up, the PCI dependency now looks, and is, entirely
arbitrary. Any bus using the of_dma_configure() mechanism will work,
so extend support to the platform and AMBA buses which do just that.
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now that we can properly describe the mapping between PCI RIDs and
stream IDs via "iommu-map", and have it fed it to the driver
automatically via of_xlate(), rework the SMMUv3 driver to benefit from
that, and get rid of the current misuse of the "iommus" binding.
Since having of_xlate wired up means that masters will now be given the
appropriate DMA ops, we also need to make sure that default domains work
properly. This necessitates dispensing with the "whole group at a time"
notion for attaching to a domain, as devices which share a group get
attached to the group's default domain one by one as they are initially
probed.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Unlike SMMUv2, SMMUv3 has no easy way to bypass unknown stream IDs,
other than allocating and filling in the entire stream table with bypass
entries, which for some configurations would waste *gigabytes* of RAM.
Otherwise, all transactions on unknown stream IDs will simply be aborted
with a C_BAD_STREAMID event.
Rather than render the system unusable in the case of an invalid DT,
avoid enabling the SMMU altogether such that everything bypasses
(though letting the explicit disable_bypass option take precedence).
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The cmdq lock is taken whenever we issue commands into the command queue,
which can occur in IRQ context (as a result of unmap) or in process
context (as a result of a threaded IRQ handler or device probe).
This can lead to a theoretical deadlock if the interrupt handler
performing the unmap hits whilst the lock is taken, so explicitly use
the {irqsave,irqrestore} spin_lock accessors for the cmdq lock.
Tested-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When the SMMUv3 driver attempts to send a command, it adds an entry to the
command queue. This is a circular buffer, where both the producer and
consumer have a wrap bit. When producer.index == consumer.index and
producer.wrap == consumer.wrap, the list is empty. When producer.index ==
consumer.index and producer.wrap != consumer.wrap, the list is full.
If the list is full when the driver needs to add a command, it waits for
the SMMU to consume one command, and advance the consumer pointer. The
problem is that we currently rely on "X before Y" operation to know if
entries have been consumed, which is a bit fiddly since it only makes
sense when the distance between X and Y is less than or equal to the size
of the queue. At the moment when the list is full, we use "Consumer before
Producer + 1", which is out of range and returns a value opposite to what
we expect: when the queue transitions to not full, we stay in the polling
loop and time out, printing an error.
Given that the actual bug was difficult to determine, simplify the polling
logic by relying exclusively on queue_full and queue_empty, that don't
have this range constraint. Polling the queue is now straightforward:
* When we want to add a command and the list is full, wait until it isn't
full and retry.
* After adding a sync, wait for the list to be empty before returning.
Suggested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
SMMUv3 only sends interrupts for event queues (EVTQ and PRIQ) when they
transition from empty to non-empty. At the moment, if the SMMU adds new
items to a queue before the event thread finished consuming a previous
batch, the driver ignores any new item. The queue is then stuck in
non-empty state and all subsequent events will be lost.
As an example, consider the following flow, where (P, C) is the SMMU view
of producer/consumer indices, and (p, c) the driver view.
P C | p c
1. SMMU appends a PPR to the PRI queue, 1 0 | 0 0
sends an MSI
2. PRIQ handler is called. 1 0 | 1 0
3. SMMU appends a PPR to the PRI queue. 2 0 | 1 0
4. PRIQ thread removes the first element. 2 1 | 1 1
5. PRIQ thread believes that the queue is empty, goes into idle
indefinitely.
To avoid this, always synchronize the producer index and drain the queue
once before leaving an event handler. In order to prevent races on the
local producer index, move all event queue handling into the threads.
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The disable_bypass cmdline option changes the SMMUv3 driver to put down
faulting stream table entries by default, as opposed to bypassing
transactions from unconfigured devices.
In this mode of operation, it is entirely expected to see aborting
entries in the stream table if and when we come to installing a valid
translation, so don't trigger a BUG() as a result of misdiagnosing these
entries as stream table corruption.
Cc: <stable@vger.kernel.org>
Fixes: 48ec83bcbc ("iommu/arm-smmu: Add initial driver support for ARM SMMUv3 devices")
Tested-by: Robin Murphy <robin.murphy@arm.com>
Reported-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In the unlikely event of a global command queue error, the ARM SMMUv3
driver attempts to convert the problematic command into a CMD_SYNC and
resume the command queue. Unfortunately, this code is pretty badly
broken:
1. It uses the index into the error string table as the CMDQ index,
so we probably read the wrong entry out of the queue
2. The arguments to queue_write are the wrong way round, so we end up
writing from the queue onto the stack.
These happily cancel out, so the kernel is likely to stay alive, but
the command queue will probably fault again when we resume.
This patch fixes the error handling code to use the correct queue index
and write back the CMD_SYNC to the faulting entry.
Cc: <stable@vger.kernel.org>
Fixes: 48ec83bcbc ("iommu/arm-smmu: Add initial driver support for ARM SMMUv3 devices")
Reported-by: Diwakar Subraveti <Diwakar.Subraveti@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The PCIe ACS capability will affect the layout of iommu groups.
Generally speaking, if the path from root port to the PCIe device
is ACS enabled, the iommu will create a single iommu group for this
PCIe device. If all PCIe devices on the path are ACS enabled then
Linux can determine this path is ACS enabled.
Linux use two PCIe configuration registers to determine the ACS
status of PCIe devices:
ACS Capability Register and ACS Control Register.
The first register is used to check the implementation of ACS function
of a PCIe device, the second register is used to check the enable status
of ACS function. If one PCIe device has implemented and enabled the ACS
function then Linux will determine this PCIe device enabled ACS.
From the Chapter:6.12 of PCI Express Base Specification Revision 3.1a,
we can find that when a PCIe device implements ACS function, the enable
status is set to disabled by default and can be enabled by ACS-aware
software.
ACS will affect the iommu groups topology, so, the iommu driver is
ACS-aware software. This patch adds a call to pci_request_acs() to the
arm-smmu driver to enable the ACS function in PCIe devices that support
it, when they get probed.
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Wei Chen <Wei.Chen@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The map_sg callback is missing from arm_smmu_ops, but is required by
iommu.h. Similarly to most other IOMMU drivers, connect it to
default_iommu_map_sg.
Cc: <stable@vger.kernel.org>
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Most users of IS_ERR_VALUE() in the kernel are wrong, as they
pass an 'int' into a function that takes an 'unsigned long'
argument. This happens to work because the type is sign-extended
on 64-bit architectures before it gets converted into an
unsigned type.
However, anything that passes an 'unsigned short' or 'unsigned int'
argument into IS_ERR_VALUE() is guaranteed to be broken, as are
8-bit integers and types that are wider than 'unsigned long'.
Andrzej Hajda has already fixed a lot of the worst abusers that
were causing actual bugs, but it would be nice to prevent any
users that are not passing 'unsigned long' arguments.
This patch changes all users of IS_ERR_VALUE() that I could find
on 32-bit ARM randconfig builds and x86 allmodconfig. For the
moment, this doesn't change the definition of IS_ERR_VALUE()
because there are probably still architecture specific users
elsewhere.
Almost all the warnings I got are for files that are better off
using 'if (err)' or 'if (err < 0)'.
The only legitimate user I could find that we get a warning for
is the (32-bit only) freescale fman driver, so I did not remove
the IS_ERR_VALUE() there but changed the type to 'unsigned long'.
For 9pfs, I just worked around one user whose calling conventions
are so obscure that I did not dare change the behavior.
I was using this definition for testing:
#define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \
unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO))
which ends up making all 16-bit or wider types work correctly with
the most plausible interpretation of what IS_ERR_VALUE() was supposed
to return according to its users, but also causes a compile-time
warning for any users that do not pass an 'unsigned long' argument.
I suggested this approach earlier this year, but back then we ended
up deciding to just fix the users that are obviously broken. After
the initial warning that caused me to get involved in the discussion
(fs/gfs2/dir.c) showed up again in the mainline kernel, Linus
asked me to send the whole thing again.
[ Updated the 9p parts as per Al Viro - Linus ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.org/lkml/2016/1/7/363
Link: https://lkml.org/lkml/2016/5/27/486
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # For nvmem part
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that we can accurately reflect the context format we choose for each
domain, do that instead of imposing the global lowest-common-denominator
restriction and potentially ending up with nothing. We currently have a
strict 1:1 correspondence between domains and context banks, so we don't
need to entertain the possibility of multiple formats _within_ a domain.
Signed-off-by: Will Deacon <will.deacon@arm.com>
[rm: split from original patch, added SMMUv3]
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Until all upstream devices have their DMA ops swizzled to point at the
SMMU, we need to treat the IOMMU_DOMAIN_DMA domain as bypass to avoid
putting devices into an empty address space when detaching from VFIO.
Signed-off-by: Will Deacon <will.deacon@arm.com>
The ARM SMMU attach_dev implementations returns -EEXIST if the device
being attached is already attached to a domain. This doesn't play nicely
with the default domain, resulting in splats such as:
WARNING: at drivers/iommu/iommu.c:1257
Modules linked in:
CPU: 3 PID: 1939 Comm: virtio-net-tx Tainted: G S 4.5.0-rc4+ #1
Hardware name: FVP Base (DT)
task: ffffffc87a9d0000 ti: ffffffc07a278000 task.ti: ffffffc07a278000
PC is at __iommu_detach_group+0x68/0xe8
LR is at __iommu_detach_group+0x48/0xe8
This patch fixes the problem by forcefully detaching the device from
its old domain, if present, when attaching to a new one. The unused
->detach_dev callback is also removed the iommu_ops structures.
Signed-off-by: Will Deacon <will.deacon@arm.com>
With DMA mapping ops provided by the iommu-dma code, only a minimal
contribution from the IOMMU driver is needed to create a suitable
DMA-API domain for them to use. Implement this for the ARM SMMUs.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
It is ILLEGAL to set STE.S1STALLD to 1 if stage 1 is enabled and
either the stall or terminate models are not supported.
This patch fixes the STALLD check and ensures that we don't set STALLD
in the STE when it is not supported.
Signed-off-by: Prem Mallappa <pmallapp@broadcom.com>
[will: consistently use IDR0_STALL_MODEL_* prefix]
Signed-off-by: Will Deacon <will.deacon@arm.com>
When acknowledging global errors, the GERRORN register should be written
with the original GERROR value so that active errors are toggled.
This patch fixed the driver to write the original GERROR value to
GERRORN, instead of an active error mask.
Signed-off-by: Prem Mallappa <pmallapp@broadcom.com>
[will: reworked use of active bits and fixed commit log]
Signed-off-by: Will Deacon <will.deacon@arm.com>
When invalidating an IOVA range potentially spanning multiple pages,
such as when removing an entire intermediate-level table, we currently
only issue an invalidation for the first IOVA of that range. Since the
architecture specifies that address-based TLB maintenance operations
target a single entry, an SMMU could feasibly retain live entries for
subsequent pages within that unmapped range, which is not good.
Make sure we hit every possible entry by iterating over the whole range
at the granularity provided by the pagetable implementation.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
[will: added missing semicolons...]
Signed-off-by: Will Deacon <will.deacon@arm.com>
IOMMU hardware with range-based TLB maintenance commands can work
happily with the iova and size arguments passed via the tlb_add_flush
callback, but for IOMMUs which require separate commands per entry in
the range, it is not straightforward to infer the necessary granularity
when it comes to issuing the actual commands.
Add an additional argument indicating the granularity for the benefit
of drivers needing to know, and update the ARM LPAE code appropriately
(for non-leaf invalidations we currently just assume the worst-case
page granularity rather than walking the table to check).
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Whilst the architecture only defines a few of the possible CERROR values,
we should handle unknown values gracefully rather than go out of bounds
trying to print out an error description.
Signed-off-by: Will Deacon <will.deacon@arm.com>
The basic flow for add a device:
arm_smmu_add_device
|->iommu_group_get_for_dev
|->iommu_group_get
return group; (1)
|->ops->device_group : Init/increase reference count to/by 1.
|->iommu_group_add_device : Increase reference count by 1.
return group (2)
|->return 0;
Since we are adding one device, the flow is (2) and the group reference
count will be increased by 2. So, we need to add iommu_group_put at the
end of arm_smmu_add_device to decrease the count by 1.
Also take the failure path into consideration when fail to add a device.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When we initialise a bypass STE, we memset the structure to zero and
set the Valid and Config fields to indicate that the stream should
bypass the SMMU. Unfortunately, this results in an SHCFG field of 0
which means that the shareability of any incoming transactions is
overridden with non-shareable, leading to potential coherence problems
down the line.
This patch fixes the issue by initialising bypass STEs to use the
incoming shareability attributes. When translation is in effect at
either stage 1 or stage 2, the shareability is determined by the
page tables.
Signed-off-by: Will Deacon <will.deacon@arm.com>
The ARM SMMUv3 driver uses dma_{alloc,free}_coherent to manage its
queues and configuration data structures.
This patch converts the driver to the managed (dmam_*) API, so that
resources are freed automatically on device teardown. This greatly
simplifies the failure paths and allows us to remove a bunch of
handcrafted freeing code.
Signed-off-by: Will Deacon <will.deacon@arm.com>
PRIQ_0_OF has been removed from the SMMUv3 architecture, so remove its
corresponding (and unused) #define from the driver.
Signed-off-by: Will Deacon <will.deacon@arm.com>
This converts the ARM SMMU and the SMMUv3 driver to use the
new device_group call-back.
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Despite being a platform device, the SMMUv3 is capable of signaling
interrupts using MSIs. Hook it into the platform MSI framework and
enjoy faults being reported in a new and exciting way.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
[will: tidied up the binding example and reworked most of the code]
Signed-off-by: Will Deacon <will.deacon@arm.com>
The bitmap allocator returns an int, which is one of the standard
negative values on failure. Rather than assigning this straight to a
u16 (like we do for the ASID and VMID callers), which means that we
won't detect failure correctly, use an int for the purposes of error
checking.
Cc: <stable@vger.kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Rather than keep a private list of struct arm_smmu_device and searching
this whenever we need to look up the correct SMMU instance, instead use
the drvdata field in the struct device to take care of the mapping for
us.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Stage-2 TLBI by IPA takes a 48-bit address field, as opposed to the
64-bit field used by the VA-based invalidation commands.
This patch re-jigs the SMMUv3 command construction code so that the
address field is correctly masked.
Signed-off-by: Will Deacon <will.deacon@arm.com>
AArch32-capable SMMU implementations have a minimum IAS of 40 bits, so
ensure that is reflected in the stage-2 page table configuration.
Signed-off-by: Will Deacon <will.deacon@arm.com>
With the io-pgtable code now enforcing its own appropriate sync points,
the vestigial flush_pgtable callback becomes entirely redundant, so
remove it altogether.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
With the correct DMA API calls now integrated into the io-pgtable code,
let that handle the flushing of non-coherent page table updates.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
A late change to the SMMUv3 architecture ensures that the OAS field
will be monotonically increasing, so we can assume that an unknown OAS
is at least 48-bit and use that, rather than fail the device probe.
Signed-off-by: Will Deacon <will.deacon@arm.com>
If the StreamIDs in a system can all be resolved by a single level-2
stream table (i.e. SIDSIZE < SPLIT), then we currently get our maths
wrong and allocate the largest strtab we support, thanks to unsigned
overflow in our calculation.
This patch fixes the issue by checking the SIDSIZE explicitly when
calculating the size of our first-level stream table.
Reported-by: Matt Evans <matt.evans@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The MSI memory attributes in the SMMUv3 driver are from an older
revision of the spec, which doesn't match the current implementations.
Out with the old, in with the new.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When an ARM SMMUv3 instance supports PRI, the driver registers
an interrupt handler, but fails to enable the generation of
such interrupt at the SMMU level.
This patches simply moves the enable flags to a variable that
gets updated by the PRI handling code before being written to the
SMMU register.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Hisilicon SMMUv3 devices treat CMD_PREFETCH_CONFIG as a illegal command,
execute it will trigger GERROR interrupt. Although the gerror code manage
to turn the prefetch into a SYNC, and the system can continue to run
normally, but it's ugly to print error information.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
[will: extended binding documentation]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Because we will choose the minimum value between STRTAB_L1_SZ_SHIFT and
IDR1.SIDSIZE, so enlarge STRTAB_L1_SZ_SHIFT will not impact the platforms
whose IDR1.SIDSIZE is smaller than old STRTAB_L1_SZ_SHIFT value.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The arm64 CPU architecture defines TCR[8:11] as holding the inner and
outer memory attributes for TTBR0.
This patch fixes the ARM SMMUv3 driver to pack these bits into the
context descriptor, rather than picking up the TTBR1 attributes as it
currently does.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
STRTAB_BASE_CFG.LOG2SIZE should be set to log2(entries), where entries
is the *total* number of entries in the stream table, not just the first
level.
This patch fixes the register setting, which was previously being set to
the size of the l1 thanks to a multi-use "size" variable.
Reported-by: Zhen Lei <thunder.leizhen@huawei.com>
Tested-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The element size of cfg->strtab is just one DWORD, so we should use a
multiply operation instead of a shift when calculating the level 1
index.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The free_io_pgtable_ops() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Version three of the ARM SMMU architecture introduces significant
changes and improvements over previous versions of the specification,
necessitating a new driver in the Linux kernel.
The main change to the programming interface is that the majority of the
configuration data has been moved from MMIO registers to in-memory data
structures, with communication between the CPU and the SMMU being
mediated via in-memory circular queues.
This patch adds an initial driver for SMMUv3 to Linux. We currently
support pinned stage-1 (DMA) and stage-2 (KVM VFIO) mappings using the
generic IO-pgtable code.
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
