[ Upstream commit 7fea67710e9f6a111a2c9440576f2396ccd92d57 ]
When call irq_get_irq_data() to get the IRQ's irq_data failed, an
appropriate error code -ENOENT should be returned. However, we directly
return 'err', which records the IRQ number instead of the error code.
Fixes: 139251fc22 ("firmware: tegra: add bpmp driver for Tegra210")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f551b5ce55575b14c26933fe9b49365ea246b3d ]
We should indicate that we're not using the HPD pin on this device, per
the binding document. Otherwise if code in the future wants to enable
HPD in the bridge when this property is absent we'll be wasting power
powering hpd when we don't use it on trogdor boards. We didn't notice
this before because the kernel driver blindly disables hpd, but that
won't be true for much longer.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: Douglas Anderson <dianders@chromium.org>
Fixes: 7ec3e67307 ("arm64: dts: qcom: sc7180-trogdor: add initial trogdor and lazor dt")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210324025534.1837405-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1cebcf9932ab76102e8cfc555879574693ba8956 ]
The Microchip LAN8710Ai PHY requires XTAL1/CLKIN external clock to be
enabled when the nRST is toggled according to datasheet Microchip
LAN8710A/LAN8710Ai DS00002164B page 35 section 3.8.5.1 Hardware Reset:
"
A Hardware reset is asserted by driving the nRST input pin low. When
driven, nRST should be held low for the minimum time detailed in
Section 5.5.3, "Power-On nRST & Configuration Strap Timing," on page
59 to ensure a proper transceiver reset. During a Hardware reset, an
external clock must be supplied to the XTAL1/CLKIN signal.
"
This is accidentally fulfilled in the current setup, where ETHCK_K is used
to supply both PHY XTAL1/CLKIN and is also fed back through eth_clk_fb to
supply ETHRX clock of the DWMAC. Hence, the DWMAC enables ETHRX clock,
that has ETHCK_K as parent, so ETHCK_K clock are also enabled, and then
the PHY reset toggles.
However, this is not always the case, e.g. in case the PHY XTAL1/CLKIN
clock are supplied by some other clock source than ETHCK_K or in case
ETHRX clock are not supplied by ETHCK_K. In the later case, ETHCK_K would
be kept disabled, while ETHRX clock would be enabled, so the PHY would
not be receiving XTAL1/CLKIN clock and the reset would fail.
Improve the DT by adding the PHY clock phandle into the PHY node, which
then also requires moving the PHY reset GPIO specifier in the same place
and that then also requires correct PHY reset GPIO timing, so add that
too.
A brief note regarding the timing, the datasheet says the reset should
stay asserted for at least 100uS and software should wait at least 200nS
after deassertion. Set both delays to 500uS which should be plenty.
Fixes: 34e0c7847d ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 516728273ddfbf51b3d0fcaac05d26e299a7b456 ]
On the production DHCOM STM32MP15xx SoM, the PHY IRQ line is connected
to the PI11 pin. Describe it in the DT as well, so the PHY IRQ can be
used e.g. to detect cable insertion and removal.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 659b38203f04f5c3d1dc60f1a3e54b582ad3841c ]
Correct the voltages in the "Power Optimized" (<= 1.5 GHz) Cortex-A57
operating point table entries for the R-Car M3-W and M3-W+ SoCs from
0.82V to 0.83V, as per the R-Car Gen3 EC Manual Errata for Revision
0.53.
Based on a patch for R-Car M3-W in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Fixes: da7e311334 ("arm64: dts: renesas: r8a7796: Add OPPs table for cpu devices")
Fixes: f51746ad7d ("arm64: dts: renesas: Add Renesas R8A77961 SoC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/b9e9db907514790574429b83d070c823b36085ef.1619699909.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44b615ac9fab16d1552cd8360454077d411e3c35 ]
Tag the highest "Power Optimized" (1.5 GHz) Cortex-A57 operating point
table entries for the RZ/G2M, R-Car M3-W and M3-W+ SoCs with the
"opp-suspend" property. This makes sure the system will enter suspend
in the same performance state as it will be resumed by the firmware
later, avoiding state inconsistencies after resume.
Based on a patch for R-Car M3-W in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Fixes: 800037e815 ("arm64: dts: renesas: r8a774a1: Add operating points")
Fixes: da7e311334 ("arm64: dts: renesas: r8a7796: Add OPPs table for cpu devices")
Fixes: f51746ad7d ("arm64: dts: renesas: Add Renesas R8A77961 SoC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/45a061c3b0463aac7d10664f47c4afdd999da50d.1619699721.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ab8c23096a29b69044209a5925758a6f88bd450 ]
"make dtbs_check" complains:
arch/arm/boot/dts/r8a7779-marzen.dt.yaml: display@fff80000: clock-names:0: 'du.0' was expected
Change the first clock name to match the DT bindings.
This has no effect on actual operation, as the Display Unit driver in
Linux does not use the first clock name on R-Car H1, but just grabs the
first clock.
Fixes: 665d79aa47 ("ARM: shmobile: marzen: Add DU external pixel clock to DT")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/9d5e1b371121883b3b3e10a3df43802a29c6a9da.1619699965.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54b909436ede47e0ee07f1765da27ec2efa41e84 ]
The scnprintf() function silently truncates the printf() and returns
the number bytes that it was able to copy (not counting the NUL
terminator). Thus, the highest value it can return here is
"NAME_SIZE - 1" and the overflow check is dead code. Fix this by
using the snprintf() function which returns the number of bytes that
would have been copied if there was enough space and changing the
condition from "> NAME_SIZE" to ">= NAME_SIZE".
Fixes: 92589c986b ("rtc-proc: permit the /proc/driver/rtc device to use other devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/YJov/pcGmhLi2pEl@mwanda
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b19d3479f25e8a0ff24df0b46c82e50ef0f900dd ]
Commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx delay
config") sets the RX/TX delay according to the phy-mode property in the
device tree. For the Orange Pi Plus board this is "rgmii", which is the
wrong setting.
Following the example of a900cac3750b ("ARM: dts: sun7i: a20: bananapro:
Fix ethernet phy-mode") the phy-mode is changed to "rgmii-id" which gets
the Ethernet working again on this board.
Fixes: bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx delay config")
Reported-by: "B.R. Oake" <broake@mailfence.com>
Reported-by: Vagrant Cascadian <vagrant@reproducible-builds.org>
Link: https://bugs.debian.org/988574
Signed-off-by: Salvatore Bonaccorso <carnil@debian.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210524122111.416885-1-carnil@debian.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 76e5624f3f9343a621dd3f4006f4e4d9c3f91e33 ]
When no child nodes are matched, an appropriate error code -ENODEV should
be returned. However, we currently do not explicitly assign this error
code to 'err'. As a result, 0 was incorrectly returned.
Fixes: fee10bd226 ("memory: pl353: Add driver for arm pl353 static memory controller")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210515040004.6983-1-thunder.leizhen@huawei.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e207457f9045343a24d936fbb67eb4b412f1c6ad ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 77750bc089 ("reset: Add Broadcom STB SW_INIT reset controller driver")
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1620789283-15048-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 907c5bbb514a4676160e79764522fff56ce3448e ]
Early exits from for_each_available_child_of_node() should decrement the
node reference counter. Reported by Coccinelle:
drivers/memory/atmel-ebi.c:593:1-33: WARNING:
Function "for_each_available_child_of_node" should have of_node_put() before return around line 604.
Fixes: 6a4ec4cd08 ("memory: add Atmel EBI (External Bus Interface) driver")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210423101815.119341-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f9dc6a357ff3b82c1e54d29fb5d52b8d4a0c587 ]
Early exits from for_each_available_child_of_node() should decrement the
node reference counter. Reported by Coccinelle:
drivers/memory/stm32-fmc2-ebi.c:1046:1-33: WARNING:
Function "for_each_available_child_of_node" should have of_node_put() before return around line 1051.
Fixes: 66b8173a19 ("memory: stm32-fmc2-ebi: add STM32 FMC2 EBI controller driver")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Christophe Kerello <christophe.kerello@foss.st.com>
Link: https://lore.kernel.org/r/20210423101815.119341-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd2f1717966535b7d0b6fe45cf0d79e94330da5f ]
There is no "max_brightness" property as pointed out by dtschema:
arch/arm/boot/dts/exynos5422-odroidxu4.dt.yaml: led-controller: led-1: 'max-brightness' is a required property
Fixes: 6658356014 ("ARM: dts: Add support Odroid XU4 board for exynos5422-odroidxu4")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210505135941.59898-5-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7e59c84cf2055a1894f45855c8319191f2fa59e ]
There is no "max_brightness" property as pointed out by dtschema:
arch/arm/boot/dts/exynos5422-odroidhc1.dt.yaml: led-controller: led-1: 'max-brightness' is a required property
Fixes: 1ac49427b5 ("ARM: dts: exynos: Add support for Hardkernel's Odroid HC1 board")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210505135941.59898-4-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75121e1dc9fe4def41e63d57f6a53749b88006ed ]
There is no "max_brightness" property. This brings the intentional
brightness reduce of green LED and dtschema checks as well:
arch/arm/boot/dts/exynos5410-odroidxu.dt.yaml: led-controller-1: led-1: 'max-brightness' is a required property
Fixes: 719f39fec5 ("ARM: dts: exynos5422-odroidxu3: Hook up PWM and use it for LEDs")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210505135941.59898-3-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48d551bf20858240f38a0276be3016ff379918ac ]
Early exits from for_each_compatible_node() should decrement the
node reference counter. Reported by Coccinelle:
arch/arm/mach-exynos/exynos.c:52:1-25: WARNING:
Function "for_each_compatible_node" should have of_node_put() before break around line 58.
Fixes: b3205dea8f ("ARM: EXYNOS: Map SYSRAM through generic DT bindings")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210425174945.164612-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 466ba3c8ff4fae39e455ff8d080b3d5503302765 ]
The driver defined of_device_id table but did not use it with
of_match_table. This prevents usual matching via devicetree and causes
a W=1 warning:
drivers/reset/reset-a10sr.c:111:34: warning:
‘a10sr_reset_of_match’ defined but not used [-Wunused-const-variable=]
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 6270068202 ("reset: Add Altera Arria10 SR Reset Controller")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210507112803.20012-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ab9d6219f86f0db916105444813aafce626a2f4 ]
The Intel Gateway reset controller is only present on Intel Gateway
platforms. Hence add a dependency on X86, to prevent asking the user
about this driver when configuring a kernel without Intel Gateway
support.
Fixes: c9aef213e3 ("reset: intel: Add system reset controller driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42f6a76fbe85e5243f83a3ed76809b1ebbb7087e ]
The Broadcom STB RESCAL reset controller is only present on Broadcom
BCM7216 platforms. Hence add a dependency on ARCH_BRCMSTB, to prevent
asking the user about this driver when configuring a kernel without
BCM7216 support.
Also, merely enabling CONFIG_COMPILE_TEST should not enable additional
code, and thus should not enable this driver by default.
Fixes: 4cf176e523 ("reset: Add Broadcom STB RESCAL reset controller")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d3bb3d27cd371d3edb43eeb1beb8ae4e92a356d ]
Two ethernet node was added by
commit 95220046a6 ("ARM: dts: Add ethernet to a bunch of platforms")
and commit d6d0cef55e ("ARM: dts: Add the FOTG210 USB host to Gemini boards")
This patch removes the duplicate one.
Fixes: d6d0cef55e ("ARM: dts: Add the FOTG210 USB host to Gemini boards")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 681ba73c72302214686401e707e2087ed11a6556 ]
ld.lld warns that the '.modinfo' section is not currently handled:
ld.lld: warning: kernel/built-in.a(workqueue.o):(.modinfo) is being placed in '.modinfo'
ld.lld: warning: kernel/built-in.a(printk/printk.o):(.modinfo) is being placed in '.modinfo'
ld.lld: warning: kernel/built-in.a(irq/spurious.o):(.modinfo) is being placed in '.modinfo'
ld.lld: warning: kernel/built-in.a(rcu/update.o):(.modinfo) is being placed in '.modinfo'
The '.modinfo' section was added in commit 898490c010 ("moduleparam:
Save information about built-in modules in separate file") to the DISCARDS
macro but Hexagon has never used that macro. The unification of DISCARDS
happened in commit 023bf6f1b8 ("linker script: unify usage of discard
definition") in 2009, prior to Hexagon being added in 2011.
Switch Hexagon over to the DISCARDS macro so that anything that is
expected to be discarded gets discarded.
Link: https://lkml.kernel.org/r/20210521011239.1332345-3-nathan@kernel.org
Fixes: e95bf452a9 ("Hexagon: Add configuration and makefiles for the Hexagon architecture.")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Brian Cain <bcain@codeaurora.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Oliver Glitta <glittao@gmail.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fef087d0d37ba7dba8f3d75566eb4c256cd6742 ]
Patch series "hexagon: Fix build error with CONFIG_STACKDEPOT and select CONFIG_ARCH_WANT_LD_ORPHAN_WARN".
This series fixes an error with ARCH=hexagon that was pointed out by the
patch "mm/slub: use stackdepot to save stack trace in objects".
The first patch fixes that error by handling the '.irqentry.text' and
'.softirqentry.text' sections.
The second patch switches Hexagon over to the common DISCARDS macro, which
should have been done when Hexagon was merged into the tree to match
commit 023bf6f1b8 ("linker script: unify usage of discard definition").
The third patch selects CONFIG_ARCH_WANT_LD_ORPHAN_WARN so that something
like this does not happen again.
This patch (of 3):
Patch "mm/slub: use stackdepot to save stack trace in objects" in -mm
selects CONFIG_STACKDEPOT when CONFIG_STACKTRACE_SUPPORT is selected and
CONFIG_STACKDEPOT requires IRQENTRY_TEXT and SOFTIRQENTRY_TEXT to be
handled after commit 505a0ef15f ("kasan: stackdepot: move
filter_irq_stacks() to stackdepot.c") due to the use of the
__{,soft}irqentry_text_{start,end} section symbols. If those sections are
not handled, the build is broken.
$ make ARCH=hexagon CROSS_COMPILE=hexagon-linux- LLVM=1 LLVM_IAS=1 defconfig all
...
ld.lld: error: undefined symbol: __irqentry_text_start
>>> referenced by stackdepot.c
>>> stackdepot.o:(filter_irq_stacks) in archive lib/built-in.a
>>> referenced by stackdepot.c
>>> stackdepot.o:(filter_irq_stacks) in archive lib/built-in.a
ld.lld: error: undefined symbol: __irqentry_text_end
>>> referenced by stackdepot.c
>>> stackdepot.o:(filter_irq_stacks) in archive lib/built-in.a
>>> referenced by stackdepot.c
>>> stackdepot.o:(filter_irq_stacks) in archive lib/built-in.a
ld.lld: error: undefined symbol: __softirqentry_text_start
>>> referenced by stackdepot.c
>>> stackdepot.o:(filter_irq_stacks) in archive lib/built-in.a
>>> referenced by stackdepot.c
>>> stackdepot.o:(filter_irq_stacks) in archive lib/built-in.a
ld.lld: error: undefined symbol: __softirqentry_text_end
>>> referenced by stackdepot.c
>>> stackdepot.o:(filter_irq_stacks) in archive lib/built-in.a
>>> referenced by stackdepot.c
>>> stackdepot.o:(filter_irq_stacks) in archive lib/built-in.a
...
Add these sections to the Hexagon linker script so the build continues to
work. ld.lld's orphan section warning would have caught this prior to the
-mm commit mentioned above:
ld.lld: warning: kernel/built-in.a(softirq.o):(.softirqentry.text) is being placed in '.softirqentry.text'
ld.lld: warning: kernel/built-in.a(softirq.o):(.softirqentry.text) is being placed in '.softirqentry.text'
ld.lld: warning: kernel/built-in.a(softirq.o):(.softirqentry.text) is being placed in '.softirqentry.text'
Link: https://lkml.kernel.org/r/20210521011239.1332345-1-nathan@kernel.org
Link: https://lkml.kernel.org/r/20210521011239.1332345-2-nathan@kernel.org
Link: https://github.com/ClangBuiltLinux/linux/issues/1381
Fixes: 505a0ef15f ("kasan: stackdepot: move filter_irq_stacks() to stackdepot.c")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Brian Cain <bcain@codeaurora.org>
Cc: Oliver Glitta <glittao@gmail.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f46f84931a0aa344678efe412d4b071d84d8a805 ]
After we grab the lock in nfs4_pnfs_ds_connect(), there is no check for
whether or not ds->ds_clp has already been initialised, so we can end up
adding the same transports multiple times.
Fixes: fc821d5920 ("pnfs/NFSv4.1: Add multipath capabilities to pNFS flexfiles servers over NFSv3")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b77f97a7e42adc72bd566ff8cb733ea426f74f6 ]
If the layout gets invalidated, we should wait for any outstanding
layoutget requests for that layout to complete, and we should resend
them only after re-establishing the layout stateid.
Fixes: d29b468da4f9 ("pNFS/NFSv4: Improve rejection of out-of-order layouts")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa95edf309ef31e2df4a37ebf0e5c2ca2a6772ab ]
If we have multiple outstanding layoutget requests, the current code to
update the layout barrier assumes that the outstanding layout stateids
are updated in order. That's not necessarily the case.
Instead of using the value of lo->plh_outstanding as a guesstimate for
the window of values we need to accept, just wait to update the window
until we're processing the last one. The intention here is just to
ensure that we don't process 2^31 seqid updates without also updating
the barrier.
Fixes: 1bcf34fdac5f ("pNFS/NFSv4: Update the layout barrier when we schedule a layoutreturn")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3aadf2e1614174dc81d52cbb9dabb77913b11c6 ]
After device reset, the virtqueues are not ready so clear the ready
field.
Failing to do so can result in virtio_vdpa failing to load if the device
was previously used by vhost_vdpa and the old values are ready.
virtio_vdpa expects to find VQs in "not ready" state.
Fixes: 1a86b377aa ("vdpa/mlx5: Add VDPA driver for supported mlx5 devices")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20210606053128.170399-1-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31028cbed26a8afa25533a10425ffa2ab794c76c ]
When 'SB_HW_16' check fails, the error code -ENODEV instead of 0 should be
returned, which is the same as that returned when 'WSS_HW_CMI8330' check
fails.
Fixes: 43bcd973d6 ("[ALSA] Add snd_card_set_generic_dev() call to ISA drivers")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210707074051.2663-1-thunder.leizhen@huawei.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 474bc334698df98ce07c890f1898c7e7f389b0c7 ]
When flushing out the unstable file writes as part of a COMMIT call, try
to perform most of of the data writes and waits outside the semaphore.
This means that if the client is sending the COMMIT as part of a memory
reclaim operation, then it can continue performing I/O, with contention
for the lock occurring only once the data sync is finished.
Fixes: 5011af4c69 ("nfsd: Fix stable writes")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Tested-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0755d3be2d9bb6ea38598ccd30d6bbaa1a5c3a50 ]
The sk_user_data pointer is supposed to be modified only while
holding the write_lock "sk_callback_lock", otherwise
we could race with other threads and crash the kernel.
we can't take the write_lock in nvmet_tcp_state_change()
because it would cause a deadlock, but the release_work queue
will set the pointer to NULL later so we can simply remove
the assignment.
Fixes: b5332a9f3f3d ("nvmet-tcp: fix incorrect locking in state_change sk callback")
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a2f966d0f3fa0ef6dada7ab9eda74cacee96b8a ]
It's unsafe to operate a vq from multiple threads.
Unfortunately this is exactly what we do when invoking
clean tx poll from rx napi.
Same happens with napi-tx even without the
opportunistic cleaning from the receive interrupt: that races
with processing the vq in start_xmit.
As a fix move everything that deals with the vq to under tx lock.
Fixes: b92f1e6751 ("virtio-net: transmit napi")
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71ab6a7cfbae27f86a3901daab10bfe13b3a1e3a ]
umem size is a 32 bit unsigned value so assigning it to an int could
cause false failures. Set the calculated value inside the function and
modify function name to reflect the fact it updates the size.
This bug was found during code review but never had real impact to this
date.
Fixes: 1a86b377aa ("vdpa/mlx5: Add VDPA driver for supported mlx5 devices")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20210530090349.8360-1-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3011776af16caf423f2c36d0047acd624c274fa ]
Fix copy paste bug assigning umem1 size to umem2 and umem3. The issue
was discovered when trying to use a 1:1 MR that covers the entire
address space where firmware complained that provided sizes are not
large enough. 1:1 MRs are required to support virtio_vdpa.
Fixes: 1a86b377aa ("vdpa/mlx5: Add VDPA driver for supported mlx5 devices")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20210530090317.8284-1-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f67092eff2bd40650aad54a1a1910160f41d864a ]
tegra_pcie_ep_raise_msi_irq() shifted a signed 32-bit value left by 31
bits. The behavior of this is implementation-defined.
Replace the shift by BIT(), which is well-defined.
Found by cppcheck:
$ cppcheck --enable=all drivers/pci/controller/dwc/pcie-tegra194.c
Checking drivers/pci/controller/dwc/pcie-tegra194.c ...
drivers/pci/controller/dwc/pcie-tegra194.c:1829:23: portability: Shifting signed 32-bit value by 31 bits is implementation-defined behaviour. See condition at line 1826. [shiftTooManyBitsSigned]
appl_writel(pcie, (1 << irq), APPL_MSI_CTRL_1);
^
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20210618160219.303092-1-jonathanh@nvidia.com
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1bc6ea31cb41d50302a3c9b401964cf0a88d41f9 ]
The .remove() callback disables clocks that were not enabled in
.probe(). So just probing and then unbinding the driver results in a clk
enable imbalance.
So just drop the call to disable the clocks. (Which BTW was also in the
wrong order because the call makes the PWM unfunctional and so should
have come only after pwmchip_remove()).
Fixes: 9f4c8f9607 ("pwm: imx: Add ipg clock operation")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 655832d12f2251e04031294f547c86935a0a126d ]
The legacy PCI interrupt lines need to be enabled using PCIE_APP_IRNEN bits
13 (INTA), 14 (INTB), 15 (INTC) and 16 (INTD). The old code however was
taking (for example) "13" as raw value instead of taking BIT(13). Define
the legacy PCI interrupt bits using the BIT() macro and then use these in
PCIE_APP_IRN_INT.
Link: https://lore.kernel.org/r/20210106135540.48420-1-martin.blumenstingl@googlemail.com
Fixes: ed22aaaede ("PCI: dwc: intel: PCIe RC controller driver")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rahul Tanwar <rtanwar@maxlinear.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07d6688b22e09be465652cf2da0da6bf86154df6 ]
If the count argument is larger than the xstate size, this will happily
copy beyond the end of xstate.
Fixes: 91c3dba7db ("x86/fpu/xstate: Fix PTRACE frames for XSAVES")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20210623121452.120741557@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9625895011d130033d1bc7aac0d77a9bf68ff8a6 ]
The gap handling in copy_xstate_to_kernel() is wrong when XSAVES is in
use.
Using init_fpstate for copying the init state of features which are
not set in the xstate header is only correct for the legacy area, but
not for the extended features area because when XSAVES is in use then
init_fpstate is in compacted form which means the xstate offsets which
are used to copy from init_fpstate are not valid.
Fortunately, this is not a real problem today because all extended
features in use have an all-zeros init state, but it is wrong
nevertheless and with a potentially dynamically sized init_fpstate this
would result in an access outside of the init_fpstate.
Fix this by keeping track of the last copied state in the target buffer and
explicitly zero it when there is a feature or alignment gap.
Use the compacted offset when accessing the extended feature space in
init_fpstate.
As this is not a functional issue on older kernels this is intentionally
not tagged for stable.
Fixes: b8be15d588 ("x86/fpu/xstate: Re-enable XSAVES")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20210623121451.294282032@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2dc0a201d0f59e6818ef443609f0850a32910844 ]
The interrupt affinity scheme used by this driver is incompatible with
multi-MSI as it implies moving the doorbell address to that of another MSI
group. This isn't possible for multi-MSI, as all the MSIs must have the
same doorbell address. As such it is restricted to systems with a single
CPU.
Link: https://lore.kernel.org/r/20210622152630.40842-2-sbodomerle@gmail.com
Fixes: fc54bae288 ("PCI: iproc: Allow allocation of multiple MSIs")
Reported-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sandor Bodo-Merle <sbodomerle@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Acked-by: Pali Rohár <pali@kernel.org>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e673d697b9a234fc3544ac240e173cef8c82b349 ]
Commit fc54bae288 ("PCI: iproc: Allow allocation of multiple MSIs")
introduced multi-MSI support with a broken allocation mechanism (it failed
to reserve the proper number of bits from the inner domain). Natural
alignment of the base vector number was also not guaranteed.
Link: https://lore.kernel.org/r/20210622152630.40842-1-sbodomerle@gmail.com
Fixes: fc54bae288 ("PCI: iproc: Allow allocation of multiple MSIs")
Reported-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Sandor Bodo-Merle <sbodomerle@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Acked-by: Pali Rohár <pali@kernel.org>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1fcb6fcd74a222d9ead54d405842fc763bb86262 ]
When looking into another nfs xfstests report, I found acl and
default_acl in nfs3_proc_create() and nfs3_proc_mknod() error
paths are possibly leaked. Fix them in advance.
Fixes: 013cdf1088 ("nfs: use generic posix ACL infrastructure for v3 Posix ACLs")
Cc: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: Anna Schumaker <anna.schumaker@netapp.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Joseph Qi <joseph.qi@linux.alibaba.com>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc1c56e9bbe92766d017efb5f0a0c71f80da5570 ]
If an RPC client is created without RPC_CLNT_CREATE_REUSEPORT, it should
not reuse the source port when a TCP connection is re-established.
This is currently implemented by preventing the source port being
recorded after a successful connection (the call to xs_set_srcport()).
However the source port is also recorded after a successful bind in xs_bind().
This may not be needed at all and certainly is not wanted when
RPC_CLNT_CREATE_REUSEPORT wasn't requested.
So avoid that assignment when xprt.reuseport is not set.
With this change, NFSv4.1 and later mounts use a different port number on
each connection. This is helpful with some firewalls which don't cope
well with port reuse.
Signed-off-by: NeilBrown <neilb@suse.de>
Fixes: e6237b6feb ("NFSv4.1: Don't rebind to the same source port when reconnecting to the server")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 29e85f53fb58b45b9e9276dcdf1f1cb762dd1c9f ]
In case of error, the function device_node_to_regmap() returns
ERR_PTR() and never returns NULL. The NULL test in the return
value check should be replaced with IS_ERR().
Fixes: 6d532143c9 ("watchdog: jz4740: Use regmap provided by TCU driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20210304045909.945799-1-weiyongjun1@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2c2a622d41168f9fea2aa3f76b9fbaa88531aac ]
Fix to return a negative error code from the error handling case instead
of 0, as done elsewhere in this function.
Fixes: 9ca2d73264 ("ubifs: Limit number of xattrs per inode")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d984bcf5766dbdbe95d325bb8a1b49a996fecfd4 ]
An inode is allowed to have ubifs_xattr_max_cnt() xattrs, so we must
complain only when an inode has more xattrs, having exactly
ubifs_xattr_max_cnt() xattrs is fine.
With this the maximum number of xattrs can be created without hitting
the "has too many xattrs" warning when removing it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
