There's a potential race in xennet_remove(); this is what the driver is
doing upon unregistering a network device:
1. state = read bus state
2. if state is not "Closed":
3. request to set state to "Closing"
4. wait for state to be set to "Closing"
5. request to set state to "Closed"
6. wait for state to be set to "Closed"
If the state changes to "Closed" immediately after step 1 we are stuck
forever in step 4, because the state will never go back from "Closed" to
"Closing".
Make sure to check also for state == "Closed" in step 4 to prevent the
deadlock.
Also add a 5 sec timeout any time we wait for the bus state to change,
to avoid getting stuck forever in wait_event().
Signed-off-by: Andrea Righi <andrea.righi@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
geneve_nl2info() sets 'df' conditionally, so we have to
initialize it by copying the value from existing geneve
device in geneve_changelink().
Fixes: 56c09de347 ("geneve: allow changing DF behavior after creation")
Reported-by: syzbot+7ebc2e088af5e4c0c9fa@syzkaller.appspotmail.com
Cc: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Very similar to commit 544f287b84
("bonding: check error value of register_netdevice() immediately"),
we should immediately check the return value of register_netdevice()
before doing anything else.
Fixes: 005db31d5f ("bonding: set carrier off for devices created through netlink")
Reported-and-tested-by: syzbot+bbc3a11c4da63c1b74d6@syzkaller.appspotmail.com
Cc: Beniamino Galvani <bgalvani@redhat.com>
Cc: Taehee Yoo <ap420073@gmail.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the implementation of uld_send(), the skb is consumed on all
execution paths except one. Release skb when returning NET_XMIT_DROP.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes PTP on AQC10X.
PTP support on AQC10X requires FW involvement and FW configures the
TPS data arb mode itself.
So we must make sure driver doesn't touch TPS data arb mode on AQC10x
if PTP is enabled. Otherwise, there are no timestamps even though
packets are flowing.
Fixes: 2deac71ac4 ("net: atlantic: QoS implementation: min_rate")
Signed-off-by: Egor Pomozov <epomozov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ENETC ports that register an external MDIO bus,
the bus doesn't get removed on the error bailout path
of enetc_pf_probe().
This issue became much more visible after recent:
commit 07095c025a ("net: enetc: Use DT protocol information to set up the ports")
Before this commit, one could make probing fail on the error
path only by having register_netdev() fail, which is unlikely.
But after this commit, because it moved the enetc_of_phy_get()
call up in the probing sequence, now we can trigger an mdiobus_free()
bug just by forcing enetc_alloc_msix() to return error, i.e. with the
'pci=nomsi' kernel bootarg (since ENETC relies on MSI support to work),
as the calltrace below shows:
kernel BUG at /home/eiz/work/enetc/net/drivers/net/phy/mdio_bus.c:648!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[...]
Hardware name: LS1028A RDB Board (DT)
pstate: 80000005 (Nzcv daif -PAN -UAO BTYPE=--)
pc : mdiobus_free+0x50/0x58
lr : devm_mdiobus_free+0x14/0x20
[...]
Call trace:
mdiobus_free+0x50/0x58
devm_mdiobus_free+0x14/0x20
release_nodes+0x138/0x228
devres_release_all+0x38/0x60
really_probe+0x1c8/0x368
driver_probe_device+0x5c/0xc0
device_driver_attach+0x74/0x80
__driver_attach+0x8c/0xd8
bus_for_each_dev+0x7c/0xd8
driver_attach+0x24/0x30
bus_add_driver+0x154/0x200
driver_register+0x64/0x120
__pci_register_driver+0x44/0x50
enetc_pf_driver_init+0x24/0x30
do_one_initcall+0x60/0x1c0
kernel_init_freeable+0x1fc/0x274
kernel_init+0x14/0x110
ret_from_fork+0x10/0x34
Fixes: ebfcb23d62 ("enetc: Add ENETC PF level external MDIO support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently drive supports taprio offload which is a tc feature offloaded
to cpsw hardware. So driver has to set the hw feature flag, NETIF_F_HW_TC
in the net device to be compliant. This patch adds the flag.
Fixes: 8127224c27 ("ethernet: ti: am65-cpsw-qos: add TAPRIO offload support")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When regmap_update_bits failed in ave_init(), calls of the functions
reset_control_assert() and clk_disable_unprepare() were missed.
Add goto out_reset_assert to do this.
Fixes: 57878f2f46 ("net: ethernet: ave: add support for phy-mode setting of system controller")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Reviewed-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is not working because of problems of its receiving code.
This patch fixes it to make it work.
When the driver receives an LAPB frame, it should first pass the frame
to the LAPB module to process. After processing, the LAPB module passes
the data (the packet) back to the driver, the driver should then add a
one-byte pseudo header and pass the data to upper layers.
The changes to the "x25_asy_bump" function and the
"x25_asy_data_indication" function are to correctly implement this
procedure.
Also, the "x25_asy_unesc" function ignores any frame that is shorter
than 3 bytes. However the shortest frames are 2-byte long. So we need
to change it to allow 2-byte frames to pass.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Reviewed-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was found that qed_pglueb_rbc_attn_handler() can produce a lot of
false-positive error detections on driver load/reload (especially after
crashes/recoveries) and spam the kernel log:
[ 4.958275] [qed_pglueb_rbc_attn_handler:324()]ICPL error - 00d00ff0
[ 2079.146764] [qed_pglueb_rbc_attn_handler:324()]ICPL error - 00d80ff0
[ 2116.374631] [qed_pglueb_rbc_attn_handler:324()]ICPL error - 00d80ff0
[ 2135.250564] [qed_pglueb_rbc_attn_handler:324()]ICPL error - 00d80ff0
[...]
Reduce the logging level of two false-positive prone error messages from
notice to verbose on initialization (only) to not mix it with real error
attentions while debugging.
Fixes: 666db4862f ("qed: Revise load sequence to avoid PCI errors")
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the verbosity of the "don't support RoCE & iWARP simultaneously"
warning to debug level to stop flooding on driver/hardware initialization:
[ 4.783230] qede 01:00.00: Storm FW 8.37.7.0, Management FW 8.52.9.0
[MBI 15.10.6] [eth0]
[ 4.810020] [qed_rdma_set_pf_params:2076()]Current day drivers don't
support RoCE & iWARP simultaneously on the same PF. Default to RoCE-only
[ 4.861186] qede 01:00.01: Storm FW 8.37.7.0, Management FW 8.52.9.0
[MBI 15.10.6] [eth1]
[ 4.893311] [qed_rdma_set_pf_params:2076()]Current day drivers don't
support RoCE & iWARP simultaneously on the same PF. Default to RoCE-only
[ 5.181713] qede a1:00.00: Storm FW 8.37.7.0, Management FW 8.52.9.0
[MBI 15.10.6] [eth2]
[ 5.224740] [qed_rdma_set_pf_params:2076()]Current day drivers don't
support RoCE & iWARP simultaneously on the same PF. Default to RoCE-only
[ 5.276449] qede a1:00.01: Storm FW 8.37.7.0, Management FW 8.52.9.0
[MBI 15.10.6] [eth3]
[ 5.318671] [qed_rdma_set_pf_params:2076()]Current day drivers don't
support RoCE & iWARP simultaneously on the same PF. Default to RoCE-only
[ 5.369548] qede a1:00.02: Storm FW 8.37.7.0, Management FW 8.52.9.0
[MBI 15.10.6] [eth4]
[ 5.411645] [qed_rdma_set_pf_params:2076()]Current day drivers don't
support RoCE & iWARP simultaneously on the same PF. Default to RoCE-only
Fixes: e0a8f9de16 ("qed: Add iWARP enablement support")
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the nsim_create(), rtnl_lock() is called before nsim_bpf_init().
If nsim_bpf_init() is failed, rtnl_unlock() should be called,
but it isn't called.
So, unbalanced locking would occur.
Fixes: e05b2d141f ("netdevsim: move netdev creation/destruction to dev probe")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing "ip link set dev ... up" for a ksz9477 backed link,
ksz9477_phy_setup is called and it calls phy_remove_link_mode to remove
1000baseT HDX. During phy_remove_link_mode, phy_advertise_supported is
called. Doing so reverts any previous change to advertised link modes
e.g. using a udevd .link file.
phy_remove_link_mode is not meant to be used while opening a link and
should be called during phy probe when the link is not yet available to
userspace.
Therefore move the phy_remove_link_mode calls into
ksz9477_switch_register. It indirectly calls dsa_register_switch, which
creates the relevant struct phy_devices and we update the link modes
right after that. At that time dev->features is already initialized by
ksz9477_switch_detect.
Remove phy_setup from ksz_dev_ops as no users remain.
Link: https://lore.kernel.org/netdev/20200715192722.GD1256692@lunn.ch/
Fixes: 42fc6a4c61 ("net: dsa: microchip: prepare PHY for proper advertisement")
Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, PF queries the MAC link status per second by calling
function hclge_get_mac_link_status(). It return the error code
when failed to send cmdq command to firmware. It's incorrect,
because this return value is used as the MAC link status, which
0 means link down, and none-zero means link up. So fixes it.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The content of the TX desc is automatically cleared by the HW
when the HW has sent out the packet to the wire. When desc filling
fails in hns3_nic_net_xmit(), it will call hns3_clear_desc() to do
the error handling, which miss zeroing of the TX desc and the
checking if a unmapping is needed.
So add the zeroing and checking in hns3_clear_desc() to avoid the
above problem. Also add DESC_TYPE_UNKNOWN to indicate the info in
desc_cb is not valid, because hns3_nic_reclaim_desc() may treat
the desc_cb->type of zero as packet and add to the sent pkt
statistics accordingly.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With GRO and fraglist support, the SKB can be aggregated to
a total size of 65535, and when that SKB is forwarded through
a bridge, the size of the SKB may be pushed to exceed the size
of 65535 when br_dev_queue_push_xmit() is called.
The max send size of BD supported by the HW is 65535, when a SKB
with a headlen of over 65535 is sent to the driver, the driver
needs to use multi BD to send the linear data, and the send size
of the last BD is calculated incorrectly by the driver who is
using '&' operation, which causes a TX error.
Use '%' operation to fix this problem.
Fixes: 3fe13ed95d ("net: hns3: avoid mult + div op in critical data path")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a big TX buffer is sent using multi BD, the driver maps the
whole TX buffer, and unmaps it using info in desc_cb corresponding
to each BD, but only the info in the desc_cb of first BD is correct,
other info in desc_cb is wrong, which causes TX unmapping problem
when SMMU is on.
Only set the mapping and freeing info in the desc_cb of first BD to
fix this problem, because the TX buffer only need to be unmapped and
freed once.
Fixes: 1e8a7977d09f("net: hns3: add handling for big TX fragment")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huzhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the report of [1], this driver is possible to cause
the following error in ravb_tx_timeout_work().
ravb e6800000.ethernet ethernet: failed to switch device to config mode
This error means that the hardware could not change the state
from "Operation" to "Configuration" while some tx and/or rx queue
are operating. After that, ravb_config() in ravb_dmac_init() will fail,
and then any descriptors will be not allocaled anymore so that NULL
pointer dereference happens after that on ravb_start_xmit().
To fix the issue, the ravb_tx_timeout_work() should check
the return values of ravb_stop_dma() and ravb_dmac_init().
If ravb_stop_dma() fails, ravb_tx_timeout_work() re-enables TX and RX
and just exits. If ravb_dmac_init() fails, just exits.
[1]
https://lore.kernel.org/linux-renesas-soc/20200518045452.2390-1-dirk.behme@de.bosch.com/
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the warning: [-Werror=-Wframe-larger-than=]
drivers/net/ethernet/neterion/vxge/vxge-main.c:
In function'VXGE_COMPLETE_VPATH_TX.isra.37':
drivers/net/ethernet/neterion/vxge/vxge-main.c:119:1:
warning: the frame size of 1056 bytes is larger than 1024 bytes
Dropping the NR_SKB_COMPLETED to 16 is appropriate that won't
have much impact on performance and functionality.
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ag71xx_mdio_probe() forgets to call clk_disable_unprepare() when
of_reset_control_get_exclusive() failed. Add the missed call to fix it.
Fixes: d51b6ce441 ("net: ethernet: add ag71xx driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Huang Guobin <huangguobin4@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ionic_wait_on_bit_lock() was a open-coded mutex knock-off
used only for protecting the queue reset operations, and there
was no reason not to use the real thing. We can use the lock
more correctly and to better protect the queue stop and start
operations from cross threading. We can also remove a useless
and expensive bit operation from the Rx path.
This fixes a case found where the link_status_check from a link
flap could run into an MTU change and cause a crash.
Fixes: beead698b1 ("ionic: Add the basic NDO callbacks for netdev support")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure the RSS hash key is kept across a fw update by not
de-initing it when an update is happening.
Fixes: c672412f61 ("ionic: remove lifs on fw reset")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we replay the rx filters after a fw-upgrade we get new
filter_id values from the FW, which we need to save and update
in our local filter list. This allows us to delete the filters
with the correct filter_id when we're done.
Fixes: 7e4d47596b ("ionic: replay filters after fw upgrade")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add in a couple of forgotten spinlocks and fix up some of
the debug messages around filter management.
Fixes: c1e329ebec ("ionic: Add management of rx filters")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use an offset to write the second half of the regs data into the
second half of the buffer instead of overwriting the first half.
Fixes: 4d03e00a21 ("ionic: Add initial ethtool support")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mlxsw_core_trap_register fails in mlxsw_emad_init,
destroy_workqueue() shouled be called to destroy mlxsw_core->emad_wq.
Fixes: d965465b60 ("mlxsw: core: Fix possible deadlock")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dma_coerce_mask_and_coherent() fails, the alloced netdev need to be freed.
Fixes: 060ad66f97 ("dpaa_eth: change DMA device")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Schmidt says:
====================
pull-request: ieee802154 for net 2020-07-20
An update from ieee802154 for your *net* tree.
A potential memory leak fix for adf7242 from Liu Jian,
and one more HTTPS link change from Alexander A. Klimov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver forgets to call clk_disable_unprepare() in error path after
a success calling for clk_prepare_enable().
Fix to goto err_clk_disable if clk_prepare_enable() is successful.
Fixes: c80d36ff63 ("net: bcmgenet: Use devm_clk_get_optional() to get the clocks")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver forgets to call clk_disable_unprepare() in error path after
a success calling for clk_prepare_enable().
Fix to goto err_clk_disable if clk_prepare_enable() is successful.
Fixes: 99d55638d4 ("net: bcmgenet: enable NETIF_F_HIGHDMA flag")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200719113142.58304-1-grandmaster@al2klimov.de
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
If in-band negotiation or fixed-link modes are specified for a DSA
port, the DSA code will force the link down during initialisation. For
fixed-link mode, this is fine, as phylink will manage the link state.
However, for in-band mode, phylink expects the PCS to detect link,
which will not happen if the link is forced down.
There is a related issue that in in-band mode, the link could come up
while we are making configuration changes, so we should force the link
down prior to reconfiguring the interface mode.
This patch addresses both issues.
Fixes: 3be98b2d5f ("net: dsa: Down cpu/dsa ports phylink will control")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix wrong reading of upper pages for SFP EEPROM. According to "Memory
Organization" figure in SFF-8472 spec: When reading upper pages 1, 2 and
3 the offset should be set relative to zero and I2C high address 0x51
[1010001X (A2h)] is to be used.
Fixes: a45bfb5a50 ("mlxsw: core: Extend QSFP EEPROM size for ethtool")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is one RGMII check not using the phy_interface_mode_is_rgmii()
helper. This prevents the driver from configuring the MAC properly when
using a phy-mode that is not just rgmii, e.g. rgmii-rxid. This became an
issue on sama5d3 xplained since the ksz9031 driver is hadling phy-mode
properly and the phy-mode has to be set to rgmii-rxid.
Fixes: bcf3440c6d ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch disables PTP on AQC111 and AQC112 due to a known HW issue,
which can cause datapath issues.
Ideally PTP block should have been disabled via PHY provisioning, but
unfortunately many units have been shipped with enabled PTP block.
Thus, we have to work around this in the driver.
Fixes: dbcd6806af ("net: aquantia: add support for Phy access")
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Hardware Filter Block RAM may not be preserved when the GENET
block is reset during a deep sleep, so it is not sufficient to
only backup and restore the enables.
This commit clears out the HFB block and reprograms the rxnfc
rules when the system resumes from a suspended state. To support
this the bcmgenet_hfb_create_rxnfc_filter() function is modified
to access the register space directly so that it can't fail due
to memory allocation issues.
Fixes: f50932cca6 ("net: bcmgenet: add WAKE_FILTER support")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the GENET driver resumes from deep sleep the UMAC_CMD
register may not be accessible and therefore should not be
accessed from bcmgenet_wol_power_up_cfg() if the GENET has
been reset.
This commit adds a check of the RBUF_ACPI_EN flag when Wake
on Filter is enabled. A clear flag indicates that the GENET
hardware must have been reset so the remainder of the
hardware programming is bypassed.
Fixes: f50932cca6 ("net: bcmgenet: add WAKE_FILTER support")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the GENET driver resumes from deep sleep the UMAC_CMD
register may not be accessible and therefore should not be
accessed from bcmgenet_wol_power_up_cfg() if the GENET has
been reset.
This commit adds a check of the MPD_EN flag when Wake on
Magic Packet is enabled. A clear flag indicates that the
GENET hardware must have been reset so the remainder of the
hardware programming is bypassed.
Fixes: 1a1d5106c1 ("net: bcmgenet: move clk_wol management to bcmgenet_wol")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If try_toggle_control_gpio() failed in smc_drv_probe(), free_netdev(ndev)
should be called to free the ndev created earlier. Otherwise, a memleak
will occur.
Fixes: 7d2911c438 ("net: smc91x: Fix gpios for device tree based booting")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When probe fail, we should destroy the workqueue.
Fixes: 2795e8c251 ("net: ieee802154: fix a potential NULL pointer dereference")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Link: https://lore.kernel.org/r/20200717090121.2143-1-liujian56@huawei.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
From Documentation/networking/timestamping.txt:
A driver which supports hardware time stamping shall update the
struct with the actual, possibly more permissive configuration.
Do update the struct passed when we upscale the requested time
stamping mode.
Fixes: cb646e2b02 ("ptp: Added a clock driver for the National Semiconductor PHYTER.")
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix support for external PTP-aware devices such as DSA or PTP PHY:
Make sure we never time stamp tx packets when hardware time stamping
is disabled.
Check for PTP PHY being in use and then pass ioctls related to time
stamping of Ethernet packets to the PTP PHY rather than handle them
ourselves. In addition, disable our own hardware time stamping in this
case.
Fixes: 6605b730c0 ("FEC: Add time stamping code and a PTP hardware clock")
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If ax88172a_unbind() fails, make sure that the return code is
less than zero so that cleanup is done properly and avoid UAF.
Fixes: a9a51bd727 ("ax88172a: fix information leak on short answers")
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Reported-by: syzbot+4cd84f527bf4a10fc9c1@syzkaller.appspotmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The fsl_mc_get_endpoint() function can return an error or directly a
NULL pointer in case the peer device is not under the root DPRC
container. Treat this case also, otherwise it would lead to a NULL
pointer when trying to access the peer fsl_mc_device.
Fixes: 7194792308 ("dpaa2-eth: add MAC/PHY support through phylink")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is likely firmware causing this but its starting to annoy customers.
Change the message level to verbose to prevent the spam.
Note that this seems to only show up with ISCSI enabled on the HBA via the
qedi driver.
Signed-off-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is no valid MAC address in the device tree,
use a random MAC address.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size used when calling 'pci_alloc_consistent()' and
'pci_free_consistent()' should match.
Fix it and have it consistent with the corresponding call in 'rr_close()'.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of fixes for v5.8. Various important fixes for iwlwifi and
mt76.
iwlwifi
* fix sleeping under RCU
* fix a kernel crash when using compressed firmware images
mt76
* tx queueing fixes for mt7615/22/63
* locking fix
* fix a crash during watchdog reset
* fix memory leaks
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfDJcKAAoJEG4XJFUm622boM4H+wTnBdnamYPASeJ8la5D5hyk
pXcPFYwTVjC48Cs+XWpcib2AQxrgZV8fF9SdbZqqCleZGGXSXsQb6WiaSr7JxFso
gbSaUHhYpfSOXdadNBI0ho/E+NFEsnIcIxMS2BJQTe9AUXCFY3oX56ut0ioSKx4P
rkgqTe0pvYUvLR4EOwCCWUndfrAgARy2KXqNsTmCCb5tXJf2leAjGyVRteX9RJQq
GSooKPrOJRLAiyId17D7kLPc8WHVv1KxBbRUgyC046s67CzDSEBw1jOy6Q2oncvI
ZCow/i7AuZSeSw3t6HRuy4ArMuRCafk1gKEbKw6TTVg47iGHn7JqrCs+l5do7hE=
=10X3
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2020-07-13' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.8
First set of fixes for v5.8. Various important fixes for iwlwifi and
mt76.
iwlwifi
* fix sleeping under RCU
* fix a kernel crash when using compressed firmware images
mt76
* tx queueing fixes for mt7615/22/63
* locking fix
* fix a crash during watchdog reset
* fix memory leaks
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
On sparc32, tcflag_t is "unsigned long", unlike on all other
architectures, where it is "unsigned int":
drivers/net/usb/hso.c: In function ‘hso_serial_set_termios’:
include/linux/kern_levels.h:5:18: warning: format ‘%d’ expects argument of type ‘unsigned int’, but argument 4 has type ‘tcflag_t {aka long unsigned int}’ [-Wformat=]
drivers/net/usb/hso.c:1393:3: note: in expansion of macro ‘hso_dbg’
hso_dbg(0x16, "Termios called with: cflags new[%d] - old[%d]\n",
^~~~~~~
include/linux/kern_levels.h:5:18: warning: format ‘%d’ expects argument of type ‘unsigned int’, but argument 5 has type ‘tcflag_t {aka long unsigned int}’ [-Wformat=]
drivers/net/usb/hso.c:1393:3: note: in expansion of macro ‘hso_dbg’
hso_dbg(0x16, "Termios called with: cflags new[%d] - old[%d]\n",
^~~~~~~
As "unsigned long" is 32-bit on sparc32, fix this by casting all tcflag_t
parameters to "unsigned int".
While at it, use "%u" to format unsigned numbers.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
