This patch adds the dataplane hardware offload to the flowtable
infrastructure. Three new flags represent the hardware state of this
flow:
* FLOW_OFFLOAD_HW: This flow entry resides in the hardware.
* FLOW_OFFLOAD_HW_DYING: This flow entry has been scheduled to be remove
from hardware. This might be triggered by either packet path (via TCP
RST/FIN packet) or via aging.
* FLOW_OFFLOAD_HW_DEAD: This flow entry has been already removed from
the hardware, the software garbage collector can remove it from the
software flowtable.
This patch supports for:
* IPv4 only.
* Aging via FLOW_CLS_STATS, no packet and byte counter synchronization
at this stage.
This patch also adds the action callback that specifies how to convert
the flow entry into the flow_rule object that is passed to the driver.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the NFTA_FLOWTABLE_FLAGS attribute that allows users to
specify the NF_FLOWTABLE_HW_OFFLOAD flag. This patch also adds a new
setup interface for the flowtable type to perform the flowtable offload
block callback configuration.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the infrastructure to support for flow entry types.
The initial type is NF_FLOW_OFFLOAD_ROUTE that stores the routing
information into the flow entry to define a fastpath for the classic
forwarding path.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move rcu_head to struct flow_offload, then remove the flow_offload_entry
structure definition.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers do not have access to the flow_offload structure, hence remove
this union from this flow_offload object as well as the original comment
on top of it.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify this code by storing the pointer to conntrack object in the
flow_offload structure.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: linux-bluetooth 2019-11-11
Here's one more bluetooth-next pull request for the 5.5 kernel release.
- Several fixes for LE advertising
- Added PM support to hci_qca driver
- Added support for WCN3991 SoC in hci_qca driver
- Added DT bindings for BCM43540 module
- A few other small cleanups/fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEmvEkXzgOfc881GuFWsYho5HknSAFAl3J1ekTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRBaxiGjkeSdILUKB/9mYalSK5f4n/AalnsEoGy3IWVy/xwG
KvAdZAueH2uFIhu6MfqmWbs9xp94kGsI9RP1o3UDzwLxBaol8cG97oi0T1Fn5670
LSzBkR5WXEVaerw7noGwVEvi/IKkSCO7pOI3PszwITHU+P/w/EChVLyeWnzDoTaf
bzSXbtXQTOCINepIic+f1COffyJA4o84uiEFwpkuTJPbiihxr43bGrwj0xb1cWC9
Zh464vGuA7s2/Xqhsmg/Z/BU5ihWIz3/wEAqKUW99dj1rUpgdaChTFEO1femXInX
WkOi6r4EZGsAB0Cbbp6hTkovK9UF94asVMOW74Yz9UK9dxEakcwmR7XK
=S7hM
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-5.5-20191111' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2019-10-07
this is a pull request for net-next/master consisting of 32 patches.
The first patch is by Gustavo A. R. Silva and removes unused code in the
generic CAN infrastructure.
The next three patches target the mcp251x driver. The one by Andy
Shevchenko removes the legacy platform data support from the driver. The
other two are by Timo Schlüßler and reset the device only when needed,
to prevent glitches on the output when GPIO support is added.
I'm contributing two patches fixing checkpatch warnings in the
c_can_platform and peak_canfd driver.
Stephane Grosjean's patch for the peak_canfd driver adds hw timestamps
support in rx skbs.
The next three patches target the xilinx_can driver. One patch by me to
fix checkpatch warnings, one patch by Anssi Hannula to avoid non
requested bus error frames, and a patch by YueHaibing that switches the
driver to devm_platform_ioremap_resource().
Pankaj Sharma contributes two patches for the m_can driver, the first
one adds support for one shot mode, the other support for handling
arbitration errors.
Followed by four patches by YueHaibing, switching the grcan, ifi, rcar,
and sun4i drivers to devm_platform_ioremap_resource()
I'm contributing cleanup patches for the rx-offload helper, while Joakim
Zhang's patch prepares the rx-offload helper for CAN-FD support. The rx
offload users flexcan and ti_hecc are converted accordingly.
The remaining twelve patches target the flexcan driver. First Joakim
Zhang switches the driver to devm_platform_ioremap_resource(). The
remaining eleven patch are by me and clean up the abstract the access of
the iflag1 and iflag2 register both for RX and TX mailboxes. This is a
preparation for the upcoming CAN-FD support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The sfc driver can drop packets processed with XDP, notably when running
out of buffer space on XDP_TX, or returning an unknown XDP action.
This increments the rx_xdp_bad_drops ethtool counter.
Call trace_xdp_exception everywhere rx_xdp_bad_drops is incremented,
except for fragmented RX packets as the XDP program hasn't run yet.
This allows it to easily be monitored from userspace.
This mirrors the behavior of other drivers.
Signed-off-by: Arthur Fabre <afabre@cloudflare.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When do randbuilding, we got this warning:
WARNING: unmet direct dependencies detected for PTP_1588_CLOCK
Depends on [n]: NET [=y] && POSIX_TIMERS [=n]
Selected by [y]:
- PTP_1588_CLOCK_IDTCM [=y]
Make PTP_1588_CLOCK_IDTCM depends on PTP_1588_CLOCK to fix this.
Fixes: 3a6ba7dc77 ("ptp: Add a ptp clock driver for IDT ClockMatrix.")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
after commit 4097e9d250 ("net: sched: don't use tc_action->order during
action dump"), 'act->order' is initialized but then it's no more read, so
we can just remove this member of struct tc_action.
CC: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a stray semicolon in an if statement that will cause a dev_err
message to be printed unconditionally. Fix this by removing the stray
semicolon.
Addresses-Coverity: ("Stay semicolon")
Fixes: f0942e00a1 ("net: dsa: mv88e6xxx: Add support for port mirroring")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aya Levin says:
====================
Update devlink binary output
This series changes the devlink binary interface:
-The first patch forces binary values to be enclosed in an array. In
addition, devlink_fmsg_binary_pair_put breaks the binary value into
chunks to comply with devlink's restriction for value length.
-The second patch removes redundant code and uses the fixed devlink
interface (devlink_fmsg_binary_pair_put).
-The third patch make self test to use the updated devlink
interface.
-The fourth, adds a verification of dumping a very large binary
content. This test verifies breaking the data into chunks in a valid
JSON output.
Series was generated against net-next commit:
ca22d6977b Merge branch 'stmmac-next'
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test of 2 PAGEs size (exceeds devlink previous length limitation)
of binary data on a 'devlink health dump show' command. Set binary length
to 8192, issue a dump show command and clear it.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update dummy reporter's output to use updated devlink interface of
binary fmsg pair.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove redundant code from fw_fatal reporter's dump callback. Use
updated devlink interface of binary fmsg pair which breaks the output
into chunks internally.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devlink supports pair output of name and value. When the value is
binary, it must be presented in an array. If the length of the binary
value exceeds fmsg limitation, break the value into chunks internally.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building with SFP disabled, the stub for sfp_bus_add_upstream()
missed "inline". Add it.
Fixes: 727b3668b7 ("net: sfp: rework upstream interface")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warnings:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_tc_mqprio.c:242:6: warning: symbol 'cxgb4_mqprio_free_hw_resources' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 2d0cb84dd9 ("cxgb4: add ETHOFLD hardware queue support")
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
zhengbin says:
====================
net: atlantic: make some symbol & function static
v1->v2: add Fixes tag
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warnings:
drivers/net/ethernet/aquantia/atlantic/aq_ethtool.c:706:5: warning: symbol 'aq_ethtool_get_priv_flags' was not declared. Should it be static?
drivers/net/ethernet/aquantia/atlantic/aq_ethtool.c:713:5: warning: symbol 'aq_ethtool_set_priv_flags' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: ea4b4d7fc1 ("net: atlantic: loopback tests via private flags")
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warnings:
drivers/net/ethernet/aquantia/atlantic/aq_pci_func.c:426:25: warning: symbol 'aq_pm_ops' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 8aaa112a57 ("net: atlantic: refactoring pm logic")
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Add extended ACK for EMADs
Shalom says:
Ethernet Management Datagrams (EMADs) are Ethernet packets sent between
the driver and device's firmware. They are used to pass various
configurations to the device, but also to get events (e.g., port up)
from it. After the Ethernet header, these packets are built in a TLV
format.
Up until now, whenever the driver issued an erroneous register access it
only got an error code indicating a bad parameter was used. This patch
set adds a new TLV (string TLV) that can be used by the firmware to
encode a 128 character string describing the error. The new TLV is
allocated by the driver and set to zeros. In case of error, the driver
will check the length of the string in the response and report it using
devlink hwerr tracepoint.
Example:
$ perf record -a -q -e devlink:devlink_hwerr &
$ pkill -2 perf
$ perf script -F trace:event,trace | grep hwerr
devlink:devlink_hwerr: bus_name=pci dev_name=0000:03:00.0 driver_name=mlxsw_spectrum err=7 (tid=9913892d00001593,reg_id=8018(rauhtd)) bad parameter (inside er_rauhtd_write_query(), num_rec=32 is over the maximum number of records supported)
Patch #1 parses the offsets of the different TLVs in incoming EMADs and
stores them in the skb's control block. This makes it easier to later
add new TLVs.
Patches #2-#3 remove deprecated TLVs and add string TLV definition.
Patches #4-#7 gradually add support for the new string TLV.
v2:
* Use existing devlink hwerr tracepoint to report the error string,
instead of printing it to kernel log
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to enable EMAD string TLV only after using the required firmware
version.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the firmware had an error while processing EMADs, it can send back
an ASCII string with the reason using EMAD string TLV.
This patch adds the support for using EMAD string TLV. In case of an error,
reports the reason using devlink hwerr tracepoint.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend EMAD information reported to devlink hwerr tracepoint with
transaction id and reg id (both, hex and string).
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During parsing of incoming EMADs, fill the string TLV's offset when it is
used.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add EMAD string TLV, an ASCII string the driver can receive from the
firmware in case of an error.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now the code assumes a fixed structure which makes it difficult to
support EMADs with and without new TLVs.
Make it more generic by parsing the TLVs when the EMADs are received and
store the offset to the different TLVs in the control block. Using these
offsets to extract information from the EMADs without relying on a specific
structure.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If TI_DAVINCI_EMAC=y and GENERIC_ALLOCATOR is not set,
below erros can be seen:
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_desc_pool_destroy.isra.14':
davinci_cpdma.c:(.text+0x359): undefined reference to `gen_pool_size'
davinci_cpdma.c:(.text+0x365): undefined reference to `gen_pool_avail'
davinci_cpdma.c:(.text+0x373): undefined reference to `gen_pool_avail'
davinci_cpdma.c:(.text+0x37f): undefined reference to `gen_pool_size'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `__cpdma_chan_free':
davinci_cpdma.c:(.text+0x4a2): undefined reference to `gen_pool_free_owner'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_chan_submit_si':
davinci_cpdma.c:(.text+0x66c): undefined reference to `gen_pool_alloc_algo_owner'
davinci_cpdma.c:(.text+0x805): undefined reference to `gen_pool_free_owner'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_ctlr_create':
davinci_cpdma.c:(.text+0xabd): undefined reference to `devm_gen_pool_create'
davinci_cpdma.c:(.text+0xb79): undefined reference to `gen_pool_add_owner'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_check_free_tx_desc':
davinci_cpdma.c:(.text+0x16c6): undefined reference to `gen_pool_avail'
This patch mades TI_DAVINCI_EMAC select GENERIC_ALLOCATOR.
Fixes: 99f6297182 ("net: ethernet: ti: cpsw: drop TI_DAVINCI_CPDMA config option")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu says:
====================
net: stmmac: Improvements for -next
Misc improvements for stmmac.
Patch 1/6, fixes a sparse warning that was introduced in recent commit in
-next.
Patch 2/6, adds the Split Header support which is also available in XGMAC
cores and now in GMAC4+ with this patch.
Patch 3/6, adds the C45 support for MDIO transactions when using XGMAC cores.
Patch 4/6, removes the speed dependency on CBS callbacks so that it can be used
in XGMAC cores.
Patch 5/6, reworks the over-engineered stmmac_rx() function so that its easier
to read.
Patch 6/6, implements the UDP Segmentation Offload feature in GMAC4+ cores.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the UDP Segmentation Offload feature in stmmac. This is only
available in GMAC4+ cores.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This looks over-engineered. Let's use some helpers to get the buffer
length and hereby simplify the stmmac_rx() function. No performance drop
was seen with the new implementation.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XGMAC3 supports full CBS features with speeds that can go up to 10G so
we can now remove the maximum speed check of CBS.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the support for C45 PHYs in the MDIO callbacks for XGMAC. This was
tested using Synopsys DesignWare XPCS.
v2:
- Pull out the readl_poll_timeout() calls into common code (Andrew)
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GMAC4+ cores also support the Split Header feature.
Add the support for Split Header feature in the RX path following the
same implementation logic that XGMAC followed.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VID is converted to le16 so the variable must be __le16 type.
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: c7ab0b8088 ("net: stmmac: Fallback to VLAN Perfect filtering if HASH is not available")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable hdr_len is being assigned a value that is never read.
The assignment is redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable err is not uninitialized and hence can potentially contain
any garbage value. This may cause an error when logical or'ing the
return values from the calls to functions crypto_aead_setauthsize or
crypto_aead_setkey. Fix this by setting err to the return of
crypto_aead_setauthsize rather than or'ing in the return into the
uninitialized variable
Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: fc1b6d6de2 ("tipc: introduce TIPC encryption & authentication")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sysfs paths changed, updating to the current ones.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes in the dpaa_eth driver reduced the number of
buffer pools per interface from three to one.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Side effect of some kbuild changes resulted in breaking the
documented way to build samples/bpf/.
This patch change the samples/bpf/Makefile to work again, when
invoking make from the subdir samples/bpf/. Also update the
documentation in README.rst, to reflect the new way to build.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call devlink enable only during probe time and avoid deadlock
during reload.
Reported-by: Shalom Toledo <shalomt@mellanox.com>
Fixes: a0c76345e3 ("devlink: disallow reload operation during device cleanup")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for chip version RTL8117. Settings have been copied from
Realtek's r8168 driver, there however chip ID 54a belongs to a chip
version called RTL8168FP. It was confirmed that RTL8117 works with
Realtek's driver, so both chip versions seem to be the same or at
least compatible.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King says:
====================
sfp: Allow slow to initialise GPON modules to work
Some GPON modules take longer than the SFF MSA specified time to
initialise and respond to transactions on the I2C bus for either
both 0x50 and 0x51, or 0x51 bus addresses. Technically these modules
are non-compliant with the SFP Multi-Source Agreement, they have
been around for some time, so are difficult to just ignore.
Most of the patch series is restructuring the code to make it more
readable, and split various things into separate functions.
We split the three state machines into three separate functions, and
re-arrange them to start probing the module as soon as a module has
been detected (without waiting for the network device.) We try to
read the module's EEPROM, retrying quickly for the first second, and
then once every five seconds for about a minute until we have read
the EEPROM. So that the kernel isn't entirely silent, we print a
message indicating that we're waiting for the module to respond after
the first second, or when all retries have expired.
Once the module ID has been read, we kick off a delayed work queue
which attempts to register the hwmon, retrying for up to a minute if
the monitoring parameters are unreadable; this allows us to proceed
with module initialisation independently of the hwmon state.
With high-power modules, we wait for the netdev to be attached before
switching the module power mode, and retry this in a similar way to
before until we have successfully read and written the EEPROM at 0x51.
We also move the handling of the TX_DISABLE signal entirely to the main
state machine, and avoid probing any on-board PHY while TX_FAULT is
set.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When a module is inserted, we attempt to read read the ID from address
0x50. Once we are able to read the ID, we immediately attempt to
initialise the hwmon support by reading from address 0x51. If this
fails, then we fall into error state, and assume that the module is
not usable.
Modules such as the ALCATELLUCENT 3FE46541AA use a real EEPROM for
I2C address 0x50, which responds immediately. However, address 0x51
is an emulated, which only becomes available once the on-board firmware
has booted. This prompts us to fall into the error state.
Since the module may be usable without diagnostics, arrange for the
hwmon probe independent of the rest of the SFP itself, retrying every
5s for up to about 60s for the monitoring to become available, and
print an error message if it doesn't become available.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some GPON modules (e.g. Huawei MA5671A) take a significant amount of
time to start responding on the I2C bus, contary to the SFF
specifications.
Work around this by implementing a two-level timeout strategy, where
we initially quickly retry for the module, and then use a slower retry
after we exceed a maximum number of quick attempts.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the module insertion reporting out of the probe handling, but
after we have detected that the upstream has attached (since that is
whom we are reporting insertion to.)
Only report module removal if we had previously reported a module
insertion.
This gives cleaner semantics, and means we can probe the module before
we have an upstream attached.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
