On PCI/PCI-X HW, if packet size is less than ETH_ZLEN,
packets may get corrupted during padding by HW.
To WA this issue, pad all small packets manually.
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a check if pdev->bus->self == NULL (root bus). When attaching
a netxen NIC to a VM it can be on the root bus and the guest would
crash in netxen_mask_aer_correctable() because of a NULL pointer
dereference if CONFIG_PCIEAER is present.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A heavy-load test on a MacBookPro6,1 is still showing a substantial
amount of read errors. Increasing the maximum wait time to 128 ms
resolves the issue.
Signed-off-by: Parag Warudkar <parag.lkml@gmail.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The 'name' sysfs attribute is mandatory for hwmon devices, but was missing
in this driver.
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Commit d6cb3e41 "bnx2x: fix checksum validation" caused a performance
regression for IPv6. Rx checksum offload does not work. IPv6 packets
are passed to the stack with CHECKSUM_NONE.
The hardware obviously cannot perform IP checksum validation for IPv6,
because there is no checksum in the IPv6 header. This should not prevent
us from setting CHECKSUM_UNNECESSARY.
Tested on BCM57711.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a command status of CMD_PROTOCOL_ERR is received, this
information should be conveyed to the SCSI mid layer, not
dropped on the floor. CMD_PROTOCOL_ERR may be received
from the Smart Array for any commands destined for an external
RAID controller such as a P2000, or commands destined for tape
drives or CD/DVD-ROM drives, if for instance a cable is
disconnected. This mostly affects multipath configurations, as
disconnecting a cable on a non-multipath configuration is not
going to do anything good regardless of whether CMD_PROTOCOL_ERR
is handled correctly or not. Not handling CMD_PROTOCOL_ERR
correctly in a multipath configaration involving external RAID
controllers may cause data corruption, so this is quite a serious
bug. This bug should not normally cause a problem for direct
attached disk storage.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If a command completes with a status of CMD_PROTOCOL_ERR, this
information should be conveyed to the SCSI mid layer, not dropped
on the floor. Unlike a similar bug in the hpsa driver, this bug
only affects tape drives and CD and DVD ROM drives in the cciss
driver, and to induce it, you have to disconnect (or damage) a
cable, so it is not a very likely scenario (which would explain
why the bug has gone undetected for the last 10 years.)
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The sh_pfc_gpio_request_enable() function acquires a spinlock but fails
to release it before returning if the requested mux type is not
supported. Fix this.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
'r->cfg' is being checked for NULL. However, it is dereferenced
in the previous statements. Thus moving those statements within
the check.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Merge fixes from Andrew Morton:
"13 patches. 12 are fixes and one is a little preparatory thing for
Andi."
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (13 commits)
memory hotplug: fix section info double registration bug
mm/page_alloc: fix the page address of higher page's buddy calculation
drivers/rtc/rtc-twl.c: ensure all interrupts are disabled during probe
compiler.h: add __visible
pid-namespace: limit value of ns_last_pid to (0, max_pid)
include/net/sock.h: squelch compiler warning in sk_rmem_schedule()
slub: consider pfmemalloc_match() in get_partial_node()
slab: fix starting index for finding another object
slab: do ClearSlabPfmemalloc() for all pages of slab
nbd: clear waiting_queue on shutdown
MAINTAINERS: fix TXT maintainer list and source repo path
mm/ia64: fix a memory block size bug
memory hotplug: reset pgdat->kswapd to NULL if creating kernel thread fails
On some platforms, bootloaders are known to do some interesting RTC
programming. Without going into the obscurities as to why this may be
the case, suffice it to say the the driver should not make any
assumptions about the state of the RTC when the driver loads. In
particular, the driver probe should be sure that all interrupts are
disabled until otherwise programmed.
This was discovered when finding bursty I2C traffic every second on
Overo platforms. This I2C overhead was keeping the SoC from hitting
deep power states. The cause was found to be the RTC firing every
second on the I2C-connected TWL PMIC.
Special thanks to Felipe Balbi for suggesting to look for a rogue driver
as the source of the I2C traffic rather than the I2C driver itself.
Special thanks to Steve Sakoman for helping track down the source of the
continuous RTC interrups on the Overo boards.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Tested-by: Steve Sakoman <steve@sakoman.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Tested-by: Shubhrajyoti Datta <omaplinuxkernel@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a serious but uncommon bug in nbd which occurs when there is heavy
I/O going to the nbd device while, at the same time, a failure (server,
network) or manual disconnect of the nbd connection occurs.
There is a small window between the time that the nbd_thread is stopped
and the socket is shutdown where requests can continue to be queued to
nbd's internal waiting_queue. When this happens, those requests are
never completed or freed.
The fix is to clear the waiting_queue on shutdown of the nbd device, in
the same way that the nbd request queue (queue_head) is already being
cleared.
Signed-off-by: Paul Clements <paul.clements@steeleye.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The 'name' sysfs attribute is mandatory for hwmon devices, but was missing
in this driver.
Cc: Paul Thomas <pthomas8589@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Paul Thomas <pthomas8589@gmail.com>
This reverts commit 985f61f7ee.
This commit fixed certain cases, but ended up regressing others
due to limitations in the current KMS API. A proper fix is too
invasive for 3.6. Push it back to 3.7.
Reported-by: Andres Freund <andres@anarazel.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Couple more IPoIB fixes for regressions introduced by path database conversion
- Minor other fixes to low-level drivers (cxgb4, mlx4, qib, ocrdma)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=nqvR
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA fixes from Roland Dreier:
- A couple more IPoIB fixes for regressions introduced by path database
conversion
- Minor other fixes to low-level drivers (cxgb4, mlx4, qib, ocrdma)
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/qib: Fix failure of compliance test C14-024#06_LocalPortNum
RDMA/ocrdma: Fix CQE expansion of unsignaled WQE
mlx4_core: Fix integer overflows so 8TBs of memory registration works
IPoIB: Fix AB-BA deadlock when deleting neighbours
IPoIB: Fix memory leak in the neigh table deletion flow
RDMA/cxgb4: Move dereference below NULL test
This patch checks whether HBA is SAS2008 B0 controller.
if it is a SAS2008 B0 controller then it use IO-APIC interrupt instead of MSIX,
as SAS2008 B0 controller doesn't support MSIX interrupts.
[jejb: fix whitespace problems]
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@lsi.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch fixes the following kernel panic invoked by uninitialized fields
in the chip initialization for the 1G bnx2 iSCSI offload.
One of the bits in the chip initialization is being used by the latest
firmware to control overflow packets. When this control bit gets enabled
erroneously, it would ultimately result in a bad packet placement which would
cause the bnx2 driver to dereference a NULL ptr in the placement handler.
This can happen under certain stress I/O environment under the Linux
iSCSI offload operation.
This change only affects Broadcom's 5709 chipset.
Unable to handle kernel NULL pointer dereference at 0000000000000008 RIP:
[<ffffffff881f0e7d>] :bnx2:bnx2_poll_work+0xd0d/0x13c5
Pid: 0, comm: swapper Tainted: G ---- 2.6.18-333.el5debug #2
RIP: 0010:[<ffffffff881f0e7d>] [<ffffffff881f0e7d>] :bnx2:bnx2_poll_work+0xd0d/0x13c5
RSP: 0018:ffff8101b575bd50 EFLAGS: 00010216
RAX: 0000000000000005 RBX: ffff81007c5fb180 RCX: 0000000000000000
RDX: 0000000000000ffc RSI: 00000000817e8000 RDI: 0000000000000220
RBP: ffff81015bbd7ec0 R08: ffff8100817e9000 R09: 0000000000000000
R10: ffff81007c5fb180 R11: 00000000000000c8 R12: 000000007a25a010
R13: 0000000000000000 R14: 0000000000000005 R15: ffff810159f80558
FS: 0000000000000000(0000) GS:ffff8101afebc240(0000) knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 0000000000000008 CR3: 0000000000201000 CR4: 00000000000006a0
Process swapper (pid: 0, threadinfo ffff8101b5754000, task ffff8101afebd820)
Stack: 000000000000000b ffff810159f80000 0000000000000040 ffff810159f80520
ffff810159f80500 00cf00cf8008e84b ffffc200100939e0 ffff810009035b20
0000502900000000 000000be00000001 ffff8100817e7810 00d08101b575bea8
Call Trace:
<IRQ> [<ffffffff8008e0d0>] show_schedstat+0x1c2/0x25b
[<ffffffff881f1886>] :bnx2:bnx2_poll+0xf6/0x231
[<ffffffff8000c9b9>] net_rx_action+0xac/0x1b1
[<ffffffff800125a0>] __do_softirq+0x89/0x133
[<ffffffff8005e30c>] call_softirq+0x1c/0x28
[<ffffffff8006d5de>] do_softirq+0x2c/0x7d
[<ffffffff8006d46e>] do_IRQ+0xee/0xf7
[<ffffffff8005d625>] ret_from_intr+0x0/0xa
<EOI> [<ffffffff801a5780>] acpi_processor_idle_simple+0x1c5/0x341
[<ffffffff801a573d>] acpi_processor_idle_simple+0x182/0x341
[<ffffffff801a55bb>] acpi_processor_idle_simple+0x0/0x341
[<ffffffff80049560>] cpu_idle+0x95/0xb8
[<ffffffff80078b1c>] start_secondary+0x479/0x488
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Cc: stable@vger.kernel.org
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Clear Audio Enable bit to trigger unsolicated event to notify Audio
Driver part the HDMI hot plug change. The patch fixed the bug when
remove HDMI cable the bit was not cleared correctly.
In intel_hdmi_dpms(), if intel_hdmi->has_audio been true, the "Audio enable bit" will
be set to trigger unsolicated event to notify Alsa driver the change.
intel_hdmi->has_audio will be reset to false from intel_hdmi_detect() after
remove the hdmi cable, here's debug log:
[ 187.494153] [drm:output_poll_execute], [CONNECTOR:17:HDMI-A-1] status updated from 1 to 2
[ 187.525349] [drm:intel_hdmi_detect], HDMI: has_audio = 0
so when comes back to intel_hdmi_dpms(), the "Audio enable bit" will not be cleared. And this
cause the eld infomation and pin presence doesnot update accordingly in alsa driver side.
This patch will also trigger unsolicated event to alsa driver to notify the hot plug event:
[ 187.853159] ALSA sound/pci/hda/patch_hdmi.c:772 HDMI hot plug event: Codec=3 Pin=5 Presence_Detect=0 ELD_Valid=1
[ 187.853268] ALSA sound/pci/hda/patch_hdmi.c:990 HDMI status: Codec=3 Pin=5 Presence_Detect=0 ELD_Valid=0
Signed-off-by: Wang Xingchao <xingchao.wang@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pin-leaks persist and we get the perennial bug reports of machine
lockups to the BUG_ON(pin_count==MAX). If we instead loudly report that
the object cannot be pinned at that time it should prevent the driver from
locking up, and hopefully restore a semblance of working whilst still
leaving us a OOPS to debug.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise things migt not work too well.
Breakage introduced in
commit eb1cbe4848
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Mar 28 23:12:16 2012 +0200
drm/i915: split PLL update code out of i9xx_crtc_mode_set
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@vger.kernel.org (for 3.5 only)
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Read unit address is done for all devices during online processing to read
out LCU features. This is also done after disconnect/connect a LCU.
Some older storage hardware does not provide the capability to read unit
address configuration.
This leads to a loop trying to read unit address configuration every 30
seconds. The device is still operational but logs are flooded with error
messages.
Fix the loop by recognizing a command reject saying that the suborder
for ruac is not supported.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If a new path is available we need to verify the path data. If it is the
first path for a device the stop bits are removed after path verification.
If a pathgroup is established we need to set system characteristics for
the lcu. Therefore I/O has to be started.
If the device is stopped the set system characteristics worker may block
the path verification worker and the device is blocked.
Turn on failfast for set system characteristics CQR to prevent a deadlock
with the path verification worker.
If a pathgroup is established on a device that is not in use trigger path
verification. Maybe we were not informed about a working path.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Reviewed-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
John W. Linville says:
====================
This is a batch of fixes intended for the 3.6 stream.
Arend van Spriel sends a simple thinko fix to correct a constant,
preventing the setting of an invalid power level.
Colin Ian King gives us a simple allocation failure check to avoid a
NULL pointer dereference.
Felix Fietkau sends another ath9k tx power patch, this time disabling a
feature that has been reported to cause rx problems.
Hante Meuleman provides a pair of endian fixes for brcmfmac.
Larry Finger offers an rtlwifi fix that avoids a system lockup related
to loading the wrong firmware for RTL8188CE devices.
These have been in linux-next for a few days and I think they should be
included in the final 3.6 kernel if possible.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- A tps65217 build error fix.
- A lcp_ich regression fix caused by the MFD driver failing to initialize the
watchdog sub device due to ACPI conflicts.
- 2 MAX77693 interrupt handling bug fixes.
- An MFD core fix, adding an IRQ domain argument to the MFD device addition
API in order to prevent silent and potentially harmful remapping behaviour
changes for drivers supporting non-DT platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=nP/y
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull mfd fixes from Samuel Ortiz:
"This is the remaining MFD fixes for 3.6, with 5 pending fixes:
- A tps65217 build error fix.
- A lcp_ich regression fix caused by the MFD driver failing to
initialize the watchdog sub device due to ACPI conflicts.
- 2 MAX77693 interrupt handling bug fixes.
- An MFD core fix, adding an IRQ domain argument to the MFD device
addition API in order to prevent silent and potentially harmful
remapping behaviour changes for drivers supporting non-DT
platforms."
* tag 'mfd-for-linus-3.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: MAX77693: Fix NULL pointer error when initializing irqs
mfd: MAX77693: Fix interrupt handling bug
mfd: core: Push irqdomain mapping out into devices
mfd: lpc_ich: Fix a 3.5 kernel regression for iTCO_wdt driver
mfd: Move tps65217 regulator plat data handling to regulator
minor and touch only new drivers so I think these are still safe for
merging.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=tCsJ
-----END PGP SIGNATURE-----
Merge tag 'for-3.6-rc6' of git://gitorious.org/linux-pwm/linux-pwm
Pull pwm fixes from Thierry Reding:
"While this comes a bit later than I had wished, both patches are
rather minor and touch only new drivers so I think these are still
safe for merging."
* tag 'for-3.6-rc6' of git://gitorious.org/linux-pwm/linux-pwm:
pwm: pwm-tiehrpwm: Fix conflicting channel period setting
pwm: pwm-tiecap: Disable APWM mode after configure
Pull scsi target fixes from Nicholas Bellinger:
"Here is the current set of target-pending fixes headed for v3.6-final
The main parts of this series include bug-fixes from Paolo Bonzini to
address an use-after-free bug in pSCSI sense exception handling, along
with addressing some long-standing bugs wrt the handling of zero-
length SCSI CDB payloads also specific to pSCSI pass-through device
backends."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: go through normal processing for zero-length REQUEST_SENSE
target: support zero allocation length in REQUEST SENSE
target: support zero-size allocation lengths in transport_kmap_data_sg
target: fail REPORT LUNS with less than 16 bytes of payload
target: report too-small parameter lists everywhere
target: go through normal processing for zero-length PSCSI commands
target: fix use-after-free with PSCSI sense data
target: simplify code around transport_get_sense_data
target: move transport_get_sense_data
target: Check idr_get_new return value in iscsi_login_zero_tsih_s1
target: Fix ->data_length re-assignment bug with SCSI overflow
* Three ACPI device power management fixes related to checking and
setting device power states.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=TTmm
-----END PGP SIGNATURE-----
Merge tag 'pm-for-3.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael J. Wysocki:
"Three ACPI device power management fixes related to checking and
setting device power states."
* tag 'pm-for-3.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PM: Use KERN_DEBUG when no power resources are found
ACPI / PM: Fix resource_lock dead lock in acpi_power_on_device
ACPI / PM: Infer parent power state from child if unknown, v2
This patch initialize register map of MUIC device because mfd driver
of Maxim MAX77693 use regmap-muic instance of MUIC device when irqs of
Maxim MAX77693 is initialized before call max77693-muic probe() function.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reported-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch fix bug related to interrupt handling for MAX77693 devices.
- Unmask interrupt masking bit for charger/flash/muic to revolve
that interrupt isn't happened when external connector is attached.
- Fix wrong regmap instance when muic interrupt is happened.
This patch were discussed and confirm discussion about this patch on below url:
http://lkml.org/lkml/2012/7/16/118
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Currently the MFD core supports remapping MFD cell interrupts using an
irqdomain but only if the MFD is being instantiated using device tree
and only if the device tree bindings use the pattern of registering IPs
in the device tree with compatible properties. This will be actively
harmful for drivers which support non-DT platforms and use this pattern
for their DT bindings as it will mean that the core will silently change
remapping behaviour and it is also limiting for drivers which don't do
DT with this particular pattern. There is also a potential fragility if
there are interrupts not associated with MFD cells and all the cells are
omitted from the device tree for some reason.
Instead change the code to take an IRQ domain as an optional argument,
allowing drivers to take the decision about the parent domain for their
interrupts. The one current user of this feature is ab8500-core, it has
the domain lookup pushed out into the driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The managed clk functions are currently only available when the generic clk
lookup framework is build. But the managed clk functions are merely wrappers
around clk_get and clk_put and do not depend on any specifics of the generic
lookup functions and there are still quite a few custom implementations of the
clk API. So make the managed functions available whenever the clk API is
implemented.
The patch also removes the custom implementation of devm_clk_get for the
coldfire platform.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull x86 platform driver updates from Matthew Garrett:
"A few small updates for 3.6 - a trivial regression fix and a couple of
conformance updates for the gmux driver, plus some tiny fixes for
asus-wmi, eeepc-laptop and thinkpad_acpi."
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
thinkpad_acpi: buffer overflow in fan_get_status()
eeepc-laptop: fix device reference count leakage in eeepc_rfkill_hotplug()
platform/x86: fix asus_laptop.wled_type description
asus-laptop: HRWS/HWRS typo
drivers-platform-x86: remove useless #ifdef CONFIG_ACPI_VIDEO
apple-gmux: Fix port address calculation in gmux_pio_write32()
apple-gmux: Fix index read functions
apple-gmux: Obtain version info from indexed gmux
Pull i2c embedded fixes from Wolfram Sang:
"The last bunch of (typical) i2c-embedded driver fixes for 3.6.
Also update the MAINTAINERS file to point to my tree since people keep
asking where to find their patches."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: algo: pca: Fix mode selection for PCA9665
MAINTAINERS: fix tree for current i2c-embedded development
i2c: mxs: correctly setup speed for non devicetree
i2c: pnx: Fix read transactions of >= 2 bytes
i2c: pnx: Fix bit definitions
Pull drm fixes from Dave Airlie:
"I realise this a bit bigger than I would want at this point.
Exynos is a large chunk, I got them to half what they wanted already,
and hey its ARM based, so not going to hurt many people.
Radeon has only two fixes, but the PLL fixes were a bit bigger, but
required for a lot of scenarios, the fence fix is really urgent.
vmwgfx: I've pulled in a dumb ioctl support patch that I was going to
shove in later and cc stable, but we need it asap, its mainly to stop
mesa growing a really ugly dependency in userspace to run stuff on
vmware, and if I don't stick it in the kernel now, everyone will have
to ship ugly userspace libs to workaround it.
nouveau: single urgent fix found in F18 testing, causes X to not start
properly when f18 plymouth is used
i915: smattering of fixes and debug quieting
gma500: single regression fix
So as I said a bit large, but its fairly well scattered and its all
stuff I'll be shipping in F18's 3.6 kernel."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (26 commits)
drm/nouveau: fix booting with plymouth + dumb support
drm/radeon: make 64bit fences more robust v3
drm/radeon: rework pll selection (v3)
drm: Drop the NV12M and YUV420M formats
drm/exynos: remove DRM_FORMAT_NV12M from plane module
drm/exynos: fix double call of drm_prime_(init/destroy)_file_private
drm/exynos: add dummy support for dmabuf-mmap
drm/exynos: Add missing braces around sizeof in exynos_mixer.c
drm/exynos: Add missing braces around sizeof in exynos_hdmi.c
drm/exynos: Make g2d_pm_ops static
drm/exynos: Add dependency for G2D in Kconfig
drm/exynos: fixed page align bug.
drm/exynos: Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(.. [1]
drm/exynos: Use devm_* functions in exynos_drm_g2d.c file
drm/exynos: Use devm_kzalloc in exynos_drm_hdmi.c file
drm/exynos: Use devm_kzalloc in exynos_drm_vidi.c file
drm/exynos: Remove redundant check in exynos_drm_fimd.c file
drm/exynos: Remove redundant check in exynos_hdmi.c file
vmwgfx: add dumb ioctl support
gma500: Fix regression on Oaktrail devices
...
Pull networking fixes from David Miller:
1) Use after free and new device IDs in bluetooth from Andre Guedes,
Yevgeniy Melnichuk, Gustavo Padovan, and Henrik Rydberg.
2) Fix crashes with short packet lengths and VLAN in pktgen, from
Nishank Trivedi.
3) mISDN calls flush_work_sync() with locks held, fix from Karsten
Keil.
4) Packet scheduler gred parameters are reported to userspace
improperly scaled, and WRED idling is not performed correctly. All
from David Ward.
5) Fix TCP socket refcount problem in ipv6, from Julian Anastasov.
6) ibmveth device has RX queue alignment requirements which are not
being explicitly met resulting in sporadic failures, fix from
Santiago Leon.
7) Netfilter needs to take care when interpreting sockets attached to
socket buffers, they could be time-wait minisockets. Fix from Eric
Dumazet.
8) sock_edemux() has the same issue as netfilter did in #7 above, fix
from Eric Dumazet.
9) Avoid infinite loops in CBQ scheduler with some configurations, from
Eric Dumazet.
10) Deal with "Reflection scan: an Off-Path Attack on TCP", from Jozsef
Kadlecsik.
11) SCTP overcharges socket for TX packets, fix from Thomas Graf.
12) CODEL packet scheduler should not reset it's state every time it
builds a new flow, fix from Eric Dumazet.
13) Fix memory leak in nl80211, from Wei Yongjun.
14) NETROM doesn't check skb_copy_datagram_iovec() return values, from
Alan Cox.
15) l2tp ethernet was using sizeof(ETH_HLEN) instead of plain ETH_HLEN,
oops. From Eric Dumazet.
16) Fix selection of ath9k chips on which PA linearization and AM2PM
predistoration are used, from Felix Fietkau.
17) Flow steering settings in mlx4 driver need to be validated properly,
from Hadar Hen Zion.
18) bnx2x doesn't show the correct link duplex setting, from Yaniv
Rosner.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (75 commits)
pktgen: fix crash with vlan and packet size less than 46
bnx2x: Add missing afex code
bnx2x: fix registers dumped
bnx2x: correct advertisement of pause capabilities
bnx2x: display the correct duplex value
bnx2x: prevent timeouts when using PFC
bnx2x: fix stats copying logic
bnx2x: Avoid sending multiple statistics queries
net: qmi_wwan: call subdriver with control intf only
net_sched: gred: actually perform idling in WRED mode
net_sched: gred: fix qave reporting via netlink
net_sched: gred: eliminate redundant DP prio comparisons
net_sched: gred: correct comment about qavg calculation in RIO mode
mISDN: Fix wrong usage of flush_work_sync while holding locks
netfilter: log: Fix log-level processing
net-sched: sch_cbq: avoid infinite loop
net: qmi_wwan: fix Gobi device probing for un2430
net: fix net/core/sock.c build error
ixp4xx_hss: fix build failure due to missing linux/module.h inclusion
caif: move the dereference below the NULL test
...
Here are a number of USB patches, a bit more than I normally like this
late in the -rc series, but given people's vacations (myself included),
and the kernel summit, it seems to have happened this way.
All are tiny, but they add up. A number of gadget and xhci fixes, and a
few new device ids. All have been tested in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlBSFeQACgkQMUfUDdst+ykjlACfUj5OOjP+VIZ/LdXpPjeXV4/P
Ho8An2/5iut+STLa+feA8AvMsvv/WdaL
=YlCk
-----END PGP SIGNATURE-----
Merge tag 'usb-3.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here are a number of USB patches, a bit more than I normally like this
late in the -rc series, but given people's vacations (myself
included), and the kernel summit, it seems to have happened this way.
All are tiny, but they add up. A number of gadget and xhci fixes, and
a few new device ids. All have been tested in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
usb: chipidea: udc: don't stall endpoint if request list is empty in isr_tr_complete_low
usb: chipidea: cleanup dma_pool if udc_start() fails
usb: chipidea: udc: fix error path in udc_start()
usb: chipidea: udc: add pullup fuction, needed by the uvc gadget
usb: chipidea: udc: fix setup of endpoint maxpacket size
USB: option: replace ZTE K5006-Z entry with vendor class rule
EHCI: Update qTD next pointer in QH overlay region during unlink
USB: cdc-wdm: fix wdm_find_device* return value
USB: ftdi_sio: do not claim CDC ACM function
usb: dwc3: gadget: fix pending isoc handling
usb: renesas_usbhs: fixup DMA transport data alignment
usb: gadget: at91udc: Don't check for ep->ep.desc
usb: gadget: at91udc: don't overwrite driver data
usb: dwc3: core: fix incorrect usage of resource pointer
usb: musb: musbhsdma: fix IRQ check
usb: musb: tusb6010: fix error path in tusb_probe()
usb: musb: host: fix for musb_start_urb Oops
usb: gadget: dummy_hcd: add support for USB_DT_BOS on rh
usb: gadget: dummy_hcd: fixup error probe path
usb: gadget: s3c-hsotg.c: fix error return code
...
Here are 2 tiny patches for a serial driver to resolve issues that
people have reported with the 3.6-rc tree.
Both of these have been in the linux-next tree for a while now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlBSGL4ACgkQMUfUDdst+ylrhQCgy0+bmNLtsxrEjJY20ahe9sVT
Q3YAn0xmu8SJ+Bv1vJKKD6vIataVQ93a
=iZmM
-----END PGP SIGNATURE-----
Merge tag 'tty-3.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY fixes from Greg Kroah-Hartman:
"Here are 2 tiny patches for a serial driver to resolve issues that
people have reported with the 3.6-rc tree.
Both of these have been in the linux-next tree for a while now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: imx: don't reinit clock in imx_setup_ufcr()
tty: serial: imx: console write routing is unsafe on SMP
Here are a few staging tree fixes for problems that have been reported.
Nothing major, just a number of tiny driver fixes. All of these have
been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlBSF54ACgkQMUfUDdst+ykh/wCeOAGv4uwvqK8pkYpdV4+XOlM/
W1QAnRvjv4dCj0e2+W46Vp5xLPPOBePk
=IyFJ
-----END PGP SIGNATURE-----
Merge tag 'staging-3.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree fixes from Greg Kroah-Hartman:
"Here are a few staging tree fixes for problems that have been
reported.
Nothing major, just a number of tiny driver fixes. All of these have
been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'staging-3.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
drm/omap: add more new timings fields
drm/omap: update for interlaced
staging: r8712u: fix bug in r8712_recv_indicatepkt()
staging: zcache: fix cleancache race condition with shrinker
Staging: Android alarm: IOCTL command encoding fix
staging: vt6656: [BUG] - Failed connection, incorrect endian.
staging: ozwpan: fix memcmp() test in oz_set_active_pd()
staging: wlan-ng: Fix problem with wrong arguments
staging: comedi: das08: Correct AO output for das08jr-16-ao
staging: comedi: das08: Correct AI encoding for das08jr-16-ao
staging: comedi: das08: Fix PCI ref count
staging: comedi: amplc_pci230: Fix PCI ref count
staging: comedi: amplc_pc263: Fix PCI ref count
staging: comedi: amplc_pc236: Fix PCI ref count
staging: comedi: amplc_dio200: Fix PCI ref count
staging: comedi: amplc_pci224: Fix PCI ref count
drivers/iio/adc/at91_adc.c: adjust inconsistent IS_ERR and PTR_ERR
staging iio: fix potential memory leak in lis3l02dq_ring.c
staging:iio: prevent divide by zero bugs
commit a606dac368 adds support to link
devices which have _PRx, if a device does not have _PRx, a warning
message will be printed.
This commit is for ZPODD on Intel ZPODD capable platforms, on other
platforms, it has no problem if there is no power resource for this
device, so a warning here is not appropriate, change it to debug.
Reported-by: Borislav Petkov <bp@amd64.org>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Commit 3236b2d469 ("IB/qib: MADs with misset M_Keys should return
failure") introduced a return code assignment that unfortunately
introduced an unconditional exit for the routine due to missing braces.
This patch adds the braces to correct the original patch.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix CQE expansion of unsignaled WQE -- don't expand the CQE when the
WQE index of the completed CQE matches with last pending WQE (tail) in
the queue.
Signed-off-by: Parav Pandit <parav.pandit@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When using the commands below to write some data to a virtio-scsi LUN of the
QEMU guest(32-bit) with 1G physical memory(qemu -m 1024), the qemu will crash.
# sudo mkfs.ext4 /dev/sdb (/dev/sdb is the virtio-scsi LUN.)
# sudo mount /dev/sdb /mnt
# dd if=/dev/zero of=/mnt/file bs=1M count=1024
In current implementation, sg_set_buf is called to add buffers to sg list which
is put into the virtqueue eventually. But if there are some HighMem pages in
table->sgl you can not get virtual address by sg_virt. So, sg_virt(sg_elem) may
return NULL value. This will cause QEMU exit when virtqueue_map_sg is called
in QEMU because an invalid GPA is passed by virtqueue.
Two solutions are discussed here:
http://lkml.indiana.edu/hypermail/linux/kernel/1207.3/00675.html
Finally, value assignment approach was adopted because:
Value assignment creates a well-formed scatterlist, because the termination
marker in source sg_list has been set in blk_rq_map_sg(). The last entry of the
source sg_list is just copied to the the last entry in destination list. Note
that, for now, virtio_ring does not care about the form of the scatterlist and
simply processes the first out_num + in_num consecutive elements of the sg[]
array.
I have tested the patch on my workstation. QEMU would not crash any more.
Cc: <stable@vger.kernel.org> # 3.4: 4fe74b1: [SCSI] virtio-scsi: SCSI driver
Signed-off-by: Wang Sen <senwang@linux.vnet.ibm.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The code currently always selects turbo mode for PCA9665, no matter which
clock frequency is configured. This is because it compares the clock frequency
against constants reflecting (boundary / 100). Compare against real boundary
frequencies to fix the problem.
Signed-off-by: Thomas Kavanagh <tkavanagh@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
We noticed a plymouth bug on Fedora 18, and I then
noticed this stupid thinko, fixing it fixed the problem
with plymouth.
Cc: stable@vger.kernel.org
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Avoid the construction of a malformed DMA request sent to
the DMA controller.
Log message is for debug only because this condition is unlikely to
append and may only trigger at driver development time.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Stable <stable@vger.kernel.org> [2.6.31+]
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
s/dma_memcpy/slave_sg/ and it is sg length that we are
talking about.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Stable <stable@vger.kernel.org> [2.6.31+]
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This patch adds on the fixes done in commits 89dd86db78 ("mlx4_core:
Allow large mlx4_buddy bitmaps") and 3de819e6b6 ("mlx4_core: Fix
integer overflow issues around MTT table") so that memory registration
of up to 8TB (log_num_mtt=31) finally works.
It fixes integer overflows in a few mlx4_table_yyy routines in icm.c
by using a u64 intermediate variable, and int/uint issues that caused
table indexes to become nagive by setting some variables to be u32
instead of int. These problems cause crashes when a user attempted to
register > 512GB of RAM.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit 0090def("ACPI: Add interface to register/unregister device
to/from power resources") used resource_lock to protect the devices list
that relies on power resource. It caused a mutex dead lock, as below
acpi_power_on ---> lock resource_lock
__acpi_power_on
acpi_power_on_device
acpi_power_get_inferred_state
acpi_power_get_list_state ---> lock resource_lock
This patch adds a new mutex "devices_lock" to protect the devices list
and calls acpi_power_on_device in acpi_power_on, instead of
__acpi_power_on, after the resource_lock is released.
[rjw: Changed data type of a boolean variable to bool.]
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
It turns out that there are ACPI BIOSes defining device objects with
_PSx and without either _PSC or _PRx. For devices corresponding to
those ACPI objetcs __acpi_bus_get_power() returns ACPI_STATE_UNKNOWN
and their initial power states are regarded as unknown as a result.
If such a device is a parent of another power-manageable device, the
child cannot be put into a low-power state through ACPI, because
__acpi_bus_set_power() refuses to change power states of devices
whose parents' power states are unknown.
To work around this problem, observe that the ACPI power state of
a device cannot be higher-power (lower-number) than the power state
of its parent. Thus, if the device's _PSC method or the
configuration of its power resources indicates that the device is
in D0, the device's parent has to be in D0 as well. Consequently,
if the parent's power state is unknown when we've just learned that
its child's power state is D0, we can safely set the parent's
power.state field to ACPI_STATE_D0.
Tested-by: Aaron Lu <aaron.lu@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The acpi_evalf() function modifies four bytes of data but in
fan_get_status() we pass a pointer to u8. I have modified the
function to use type checking now.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Fix a device reference count leakage issue in function
eeepc_rfkill_hotplug().
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
MODULE_PARM_DESC for wlan_status is further in the same file
Signed-off-by: Maxim A. Nikulin <M.A.Nikulin@gmail.com>
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This function fails to add the start address of the gmux I/O range to
the requested port address and thus writes to the wrong location.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Study of Apple's binary driver revealed that the GMUX_READ_PORT should
be written between calls to gmux_index_wait_ready and
gmux_index_wait_complete (i.e., the new index protocol must be
followed). If this is not done correctly, the indexed
gmux device only partially accepts writes which lead to problems
concerning GPU switching. Special thanks to Seth Forshee who helped
greatly with identifying unnecessary changes.
Signed-off-by: Bernhard Froemel <froemel@vmars.tuwien.ac.at>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This patch extracts and displays version information from the indexed
gmux device as it is also done for the classic gmux device.
Signed-off-by: Bernhard Froemel <froemel@vmars.tuwien.ac.at>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Commit a334872224 added afex support but lacked
several logical changes. This lack can cause afex to crash, and also
have a slight effect on other flows (i.e., driver always assumes the Tx ring
has less available buffers than what it actually has).
This patch adds the missing segments, fixing said issues.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under traffic, there are several registers that when read (e.g., via
'ethtool -d') may cause the chip to stall.
This patch corrects the registers read in such flows.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch propagates users' requested flow-control into the link layer,
which will later be used to advertise this flow-control for auto-negotiation
(until now these values were ignored).
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this fix, the driver reported the chip's active duplex state
is always 'full', even if using half-duplex mode.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent updating the xmac PFC configuration when using a link speed
slower than 10G -the umac block is responsible for 1G or slower connections,
therefore it is possible the xmac block is reset when connection is slower.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW needs the driver statistics for management. Current logic is broken
in that the function that gathers the port statistics does not copy
its own statistics to a place where the FW can use it.
This patch causes every function that can pass statistics to the FW to
do so.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During traffic when DCB is enabled, it is possible for multiple instances
of statistics queries to be sent to the chip - this may cause the FW to assert.
This patch prevents the sending of an additional instance of statistics query
while the previous query hasn't completed.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For DP we can use the same PPLL for all active DP
encoders. Take advantage of that to prevent cases
where we may end up sharing a PPLL between DP and
non-DP which won't work. Also clean up the code
a bit.
v2: - fix missing pll_id assignment in crtc init
v3: - fix DP PPLL check
- document functions
- break in main encoder search loop after matching.
no need to keep checking additional encoders.
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=54471
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This fixes a hang on suspend due to calling wdm_suspend on
the unregistered data interface. The hang should have been
a NULL pointer reference had it not been for a logic error
in the cdc_wdm code.
commit 230718bd net: qmi_wwan: bind to both control and data interface
changed qmi_wwan to use cdc_wdm as a subdriver for devices with
a two-interface QMI/wwan function. The commit failed to update
qmi_wwan_suspend and qmi_wwan_resume, which were written to handle
either a single combined interface function, or no subdriver at all.
The result was that we called into the subdriver both when the
control interface was suspended and when the data interface was
suspended. Calling the subdriver suspend function with an
unregistered interface is not supported and will make the
subdriver bug out.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a bad idea to hold a spinlock and call flush_work_sync.
Move the workqueue cleanup outside the spinlock and use cancel_work_sync,
on closing the channel this seems to be the more correct function.
Remove the never used and constant return value of mISDN_freebchannel.
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Cc: <stable@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
They don't always appear as AHCI class devices but instead as IDE class.
Based on an initial patch by Hiroaki Nito
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=42804
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This can also appear as 0x9192. Reported in bugzilla and confirmed with the
board documentation for these boards.
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=42970
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: The Stables <stable@vger.kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The JMicron JMB362 controller supports AHCI only, but some revisions
use the IDE class code. These need to be matched by device ID.
These additions have apparently been included by QNAP in their NAS
devices using these controllers.
References: http://bugs.debian.org/634180
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Inki Dae writes:
- fix build warnings
- minor code cleanup
- remove non-standard format, DRM_FORMAT_NV12M
- add dummy mmap for exynos dmabuf
. dma_buf export needs this patch
* 'exynos-drm-fixes' of git://git.infradead.org/users/kmpark/linux-samsung:
drm: Drop the NV12M and YUV420M formats
drm/exynos: remove DRM_FORMAT_NV12M from plane module
drm/exynos: fix double call of drm_prime_(init/destroy)_file_private
drm/exynos: add dummy support for dmabuf-mmap
drm/exynos: Add missing braces around sizeof in exynos_mixer.c
drm/exynos: Add missing braces around sizeof in exynos_hdmi.c
drm/exynos: Make g2d_pm_ops static
drm/exynos: Add dependency for G2D in Kconfig
drm/exynos: fixed page align bug.
drm/exynos: Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(.. [1]
drm/exynos: Use devm_* functions in exynos_drm_g2d.c file
drm/exynos: Use devm_kzalloc in exynos_drm_hdmi.c file
drm/exynos: Use devm_kzalloc in exynos_drm_vidi.c file
drm/exynos: Remove redundant check in exynos_drm_fimd.c file
drm/exynos: Remove redundant check in exynos_hdmi.c file
this patch removes DRM_FORMAT_NV12M from plane module because this format
is same as DRM_FORMAT_NV12. DRM_FORMAT_NV12M will be identified by
mode_cmd->handles and mode_cmd->offsets fields internally.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin.park <kyungmin.park@samsung.com>
This patch adds a stub function for DMABUF mmap.
This allows to export a DMABUF.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Fixes the following checkpatch warnings:
WARNING: sizeof filter_y_horiz_tap8 should be sizeof(filter_y_horiz_tap8)
WARNING: sizeof filter_y_vert_tap4 should be sizeof(filter_y_vert_tap4)
WARNING: sizeof filter_cr_horiz_tap4 should be sizeof(filter_cr_horiz_tap4)
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Fixes the following checkpatch warnings:
WARNING: sizeof *res should be sizeof(*res)
WARNING: sizeof res->regul_bulk[0] should be sizeof(res->regul_bulk[0])
WARNING: sizeof *res should be sizeof(*res)
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Fixes the following warning:
drivers/gpu/drm/exynos/exynos_drm_g2d.c:897:1: warning:
symbol 'g2d_pm_ops' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Select Exynos DRM based G2D only if non-DRM based Exynos G2D driver
is not selected.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
do not align in page unit at dumb creation. the align is done
by exynos_drm_gem_create() to be called commonly.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The semantic patch that makes this change is available
in scripts/coccinelle/api/err_cast.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
devm_* functions are device managed functions and make error handling
and cleanup cleaner and simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
devm_kzalloc is a device managed function and makes freeing and error
handling simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
devm_kzalloc is a device managed function and makes freeing and error
handling simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
devm_request_and_ioremap function checks the validity of the
pointer returned by platform_get_resource. Hence an additional check
in the probe function is not necessary.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
devm_request_and_ioremap function checks the validity of the
pointer returned by platform_get_resource. Hence an additional check
in the probe function is not necessary.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Testing and works with the -modesetting driver,
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The register map patches didn't set one value for the GMA600 which
means the Fujitsu Q550 dies on boot with the GMA500 driver enabled.
Add the map entry so we don't read from the device MMIO + 0 by mistake.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Horses <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Daniel writes:
"Nothing really major at all:
- fixup edp setup sequence (Dave)
- disable sdvo hotplug for real, this is a fixup for a messed-up
regression fixer (Jani)
- don't expose dysfunctional backlight driver (Jani)
- properly init spinlock (only used by hsw/vlv code) from Alexander
Shishkin"
along with a couple of more fixes on top.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: fix up the IBX transcoder B check
drm/i915: set the right gen3 flip_done mode also at resume
drm/i915: initialize dpio_lock spin lock
drm/i915: do not expose a dysfunctional backlight interface to userspace
drm/i915: only enable sdvo hotplug irq if needed
drm/i915/edp: get the panel delay before powering up
Current user_buffer check is incorrect and causes hdparm to fail
# hdparm -I /dev/rssda
HDIO_DRIVE_CMD(identify) failed: Input/output error
/dev/rssda:
Patching linux-3.6-rc5 hdparm works as expected
# hdparm -I /dev/rssda
/dev/rssda:
ATA device, with non-removable media
Model Number: DELL_P320h-MTFDGAL350SAH
Serial Number: 00000000121302025F01
Firmware Revision: B1442808
<snip>
Reported-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Removed the dead code in mtip_hw_read_registers() and mtip_hw_read_flags().
Reported-by: Coverity
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Changed printk to be compliant with latest style changes
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Proper reporting of write protect status on big-endian
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Increased timeout for standby command to work with larger capacity drives
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Return error for NCQ commands when the drive is in security locked state
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
ssid len is 32 bit and needs endian conversion for big endian systems.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are a number of problems that occur for the latest version
of the Realtek RTL8188CE device with the in-kernel driver. These
include selection of the wrong firmware, and system lockup. A full
fix is known, but is too invasive for inclusion in stable. This patch
fixes the problem with loading the wrong firmware, and logs a message
that the device may not work for kernels 3.6 and older.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Cc: Anisse Astier <anisse@astier.eu>
Cc: Li Chaoming <chaoming_li@realsil.com.cn>
Tested-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When attaching an imx28 or imx53 in USB gadget mode to a Windows host and
starting a rndis connection we see this message every 4-10 seconds:
g_ether gadget: high speed config #2: RNDIS
Analysis shows that each time this message is printed, the rndis connection is
re-establish due to a reset because of a stalled endpoint (ep 0, dir 1). The
endpoint is stalled because the reqeust complete bit on that endpoint is set,
but in isr_tr_complete_low() the endpoint request list (mEp->qh.queue) is
empty.
This patch removed this check, because the code doesn't take the following
situation into account:
The loop over all endpoints in isr_tr_complete_handler() will call ep_nuke() on
both ep0/dir0 and ep/dir1 in the first loop. Pending reqeusts will be flushed
and completed here. There seems to be a race condition, the request is nuked,
but the request complete bit will be set, too. The subsequent check (in
ep0/dir1's loop cycle) for endpoint request list (mEp->qh.queue) empty will
fail.
Both other mainline chipidea drivers (mv_udc_core.c and fsl_udc_core.c) don't
have this check.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If udc_start() fails the qh_pool dma-pool cannot be closed because
it's still in use. This patch factors out the dma_pool_free() loop
into destroy_eps() and calls it in the error path of udc_start(),
too.
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the error path of udc_start(). Now NULL is used to
unset the peripheral with otg_set_peripheral().
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add function to physicaly enable or disable of pullup connection on the USB-D+
line. The uvc gaget will fail, if this function is not implemented.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch changes the setup of the endpoint maxpacket size. All non control
endpoints are initialized with an undefined ((unsigned short)~0) maxpacket
size. The maxpacket size of Endpoint 0 will be kept at CTRL_PAYLOAD_MAX.
Some gadget drivers check for the maxpacket size before they enable the
endpoint, which leads to a wrong state in these drivers.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lockdep points out a circular locking dependency betwwen the ipoib
device priv spinlock (priv->lock) and the neighbour table rwlock
(ntbl->rwlock).
In the normal path, ie neigbour garbage collection task, the neigh
table rwlock is taken first and then if the neighbour needs to be
deleted, priv->lock is taken.
However in some error paths, such as in ipoib_cm_handle_tx_wc(),
priv->lock is taken first and then ipoib_neigh_free routine is called
which in turn takes the neighbour table ntbl->rwlock.
The solution is to get rid the neigh table rwlock completely and use
only priv->lock.
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
If the neighbours hash table is empty when unloading the module, then
ipoib_flush_neighs(), the cleanup routine, isn't called and the
memory used for the hash table itself leaked.
To fix this, ipoib_flush_neighs() is allways called, and another
completion object is added to signal when the table is freed.
Once invoked, ipoib_flush_neighs() flushes all the neighbours (if
there are any), calls the the hash table RCU free routine, which now
signals completion of the deletion process, and waits for the last
neighbour to be freed.
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit cd4f2d4 (i2c: mxs: Set I2C timing registers for mxs-i2c) only
covered the case for devicetree and made platform_data based boards
bail out with -EINVAL. Correctly support the latter one, too.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
On transactions with n>=2 bytes, the controller actually wrongly clocks in n+1
bytes. This is caused by the (wrong) assumption that RFE in the Status Register
is 1 iff there is no byte already ordered (via a dummy TX byte). This lead to
the implementation of synchronized byte ordering, e.g.:
Dummy-TX - RX - Dummy-TX - RX - ...
But since RFE actually stays high after some Dummy-TX, it rather looks like:
Dummy-TX - Dummy-TX - RX - Dummy-TX - RX - (RX)
The last RX byte is clocked in by the bus controller, but ignored by the kernel
when filling the userspace buffer.
This patch fixes the issue by asking for RX via Dummy-TX asynchronously.
Introducing a separate counter for TX bytes.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The I2C Control Register bits RFDAIE and RFFIE were mixed up. In addition to
this fix, this patch adds the missing bit DRSIE for completeness.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
If the caller passes a valid kmap_op to m2p_add_override, we use
kmap_op->dev_bus_addr to store the original mfn, but dev_bus_addr is
part of the interface with Xen and if we are batching the hypercalls it
might not have been written by the hypervisor yet. That means that later
on Xen will write to it and we'll think that the original mfn is
actually what Xen has written to it.
Rather than "stealing" struct members from kmap_op, keep using
page->index to store the original mfn and add another parameter to
m2p_remove_override to get the corresponding kmap_op instead.
It is now responsibility of the caller to keep track of which kmap_op
corresponds to a particular page in the m2p_override (gntdev, the only
user of this interface that passes a valid kmap_op, is already doing that).
CC: stable@kernel.org
Reported-and-Tested-By: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The driver uses be16_to_cpu and cpu_to_be16 to convert data in SMBus word
operations from chip to host byte order. However, the data passed from and to
the SMBus word API functions is in host byte order, not in chip byte order.
Conversion should therefore use swab16 instead of be16 to change the byte order.
Replace driver internal word conversion functions with SMBus API functions to
solve the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org # 3.5+
Acked-by: Jean Delvare <khali@linux-fr.org>
dma_alloc/free_coherent APIs requires the platform specific remoteproc
device as the device parameter. We are passing vdev->dev.parent to the
dma_free_coherent function which is the generic rproc device and it is
wrong, it has to be vdev->dev.parent->parent instead, same as when we
call dma_alloc_coherent function.
Signed-off-by: Fernando Guzman Lugo <fernando.lugo@ti.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Pull crypto fixes from Herbert Xu:
"This fixes the authenc self-test crash as well as a missing export of
a symbol used by a module."
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: authenc - Fix crash with zero-length assoc data
crypto/caam: Export gen_split_key symbol for other modules
This has been added in
commit de9a35abb3
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Jun 5 11:03:40 2012 +0200
drm/i915: assert that the IBX port transcoder select w/a is implemented
Unfortunately I've failed to notice that these checks are not just
called for the port that is about to be disabled, but for all (which
makes sense for an assert ...), and the WARN missfired when disabling
another pipe than the one with the dp port.
Hence also check whether the port is actually disabled.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=54688
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
HP un2430 is a Gobi 3000 device. It was mistakenly treated as Gobi 1000
in patch b9f90eb274.
I own this device and qmi_wwan works again with this fix.
Signed-off-by: Pierre Sauter <pierre.sauter@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This set consist of three minor and one fairly major (the device not ready
causing offlining problem which is a serious regression introduced by the
media change update) fixes.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQThAIAAoJEDeqqVYsXL0MHq8H/2o01bXbTSK8aPzWBhTBmoxE
HKP6uOvsO8P7oAeGLdqY5Pl8yx0hFA5qTiBIEPJnXIObdstNuKYsJNdc3ZywxL7o
pFEJkMkDyGueVP3IADC+00YCfRPkpuoQBkuY1YIFwDwS190spxsLpNebvsW8fGtM
aKb1qVq9IrATLBVlOJsY6hn5GfF5p9Mu5jaHVQ+QvyrJNngr5igJyKxrKZT8qdnA
A2nMBcrsYh3oBWtIWg4E68iNBc32o6ur3OKNNLeKFVit1h05TOERloEqaZLE+NY3
e+aZlMt4pdBtGQQBz0ckM/vCQq7+H3Mi673UpUE5DlSfSdUJZrNSjfL9Ox6HzsI=
=BpBo
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"I had actually prepared this fix set before I left for KS + Plumbers,
so it's been incubating much longer than it should have. I'll be
picking up my three week backlog this week, so more fixes will then be
forthcoming
This set consist of three minor and one fairly major (the device not
ready causing offlining problem which is a serious regression
introduced by the media change update) fixes.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] Fix 'Device not ready' issue on mpt2sas
[SCSI] scsi_lib: fix scsi_io_completion's SG_IO error propagation
[SCSI] megaraid_sas: Move poll_aen_lock initializer
[SCSI] mpt2sas: Fix for Driver oops, when loading driver with max_queue_depth command line option to a very small value
'struct omap_video_timings' was updated w/ a 'bool interlaced'. Without
a matching update in omap_connector, this field could have undefined
values from the stack, which isn't quite ideal.
Update the fxns to convert omapdss<->drm timings structs, and zero-init
'struct omap_video_timings' when it is declared on stack to avoid issues
like this in the future.
Signed-off-by: Rob Clark <rob@ti.com>
Reviewed-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a possibility of QH overlay region having reference to a stale
qTD pointer during unlink.
Consider an endpoint having two pending qTD before unlink process begins.
The endpoint's QH queue looks like this.
qTD1 --> qTD2 --> Dummy
To unlink qTD2, QH is removed from asynchronous list and Asynchronous
Advance Doorbell is programmed. The qTD1's next qTD pointer is set to
qTD2'2 next qTD pointer and qTD2 is retired upon controller's doorbell
interrupt. If QH's current qTD pointer points to qTD1, transfer overlay
region still have reference to qTD2. But qtD2 is just unlinked and freed.
This may cause EHCI system error. Fix this by updating qTD next pointer
in QH overlay region with the qTD next pointer of the current qTD.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
64bit arches have a buggy r8712u driver, let's fix it.
skb->tail must be set properly or network stack behavior is undefined.
Addresses https://bugzilla.redhat.com/show_bug.cgi?id=847525
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=45071
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Dave Jones <davej@redhat.com>
Cc: stable <stable@vger.kernel.org> [2.6.37+]
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A logic error made the wdm_find_device* functions
return a bogus pointer into static data instead of
the intended NULL no matching device was found.
Cc: stable <stable@vger.kernel.org> # v3.4+
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 36a1211970 (netprio_cgroup.h:
dont include module.h from other includes) made the following build
error on ixp4xx_hss pop up:
CC [M] drivers/net/wan/ixp4xx_hss.o
drivers/net/wan/ixp4xx_hss.c:1412:20: error: expected ';', ',' or ')'
before string constant
drivers/net/wan/ixp4xx_hss.c:1413:25: error: expected ';', ',' or ')'
before string constant
drivers/net/wan/ixp4xx_hss.c:1414:21: error: expected ';', ',' or ')'
before string constant
drivers/net/wan/ixp4xx_hss.c:1415:19: error: expected ';', ',' or ')'
before string constant
make[8]: *** [drivers/net/wan/ixp4xx_hss.o] Error 1
This was previously hidden because ixp4xx_hss includes linux/hdlc.h which
includes linux/netdevice.h which includes linux/netprio_cgroup.h which
used to include linux/module.h. The real issue was actually present since
the initial commit that added this driver since it uses macros from
linux/module.h without including this file.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we've only frobbed this bit at irq_init time, but did
not restore it at resume time. Move it to the gen3 clock gating
function to fix this.
Notice while reading through code.
Cc: stable@vger.kernel.org (for 3.5 only)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I discovered I couldn't get sierra_net to work on a powerpc. Turns out
the firmware attribute check assumes the system is little endian and
hence fails because the attributes is a 16 bit value.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for oobirq_entry allocation failure to avoid
NULL pointer dereferencing.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some checks for PA linearization support checked ATH9K_HW_CAP_PAPRD and some
used the EEPROM ops, leading to issues in tx power handling, since those
two can be out of sync.
Disable the feature by default, since it has been reported that it can
cause damage to the rx path under some circumstances. It can now be enabled
for testing via debugfs.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver provides the cfg80211 regulatory framework with a set of
custom rules. However, there was a mismatch in number of rules
and the actual rules provided. This resulted in setting an invalid
power level:
ieee80211 phy0: brcms_ops_config: change channel 13
ieee80211 phy0: brcms_ops_config: Error setting power_level (8758364)
Closer look in cfg80211 regulatory blurb showed following bogus rule:
cfg80211: 0 KHz - -60446948 KHz @ 875836468 KHz), (875836468 mBi, 875836468 mBm)
Cc: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Microchip vid:pid 04d8:000a is used for their CDC ACM
demo firmware application. This is a device with a single
function conforming to the CDC ACM specification and with
the intention of demonstrating CDC ACM class firmware and
driver interaction. The demo is used on a number of
development boards, and may also be used unmodified by
vendors using Microchip hardware.
Some vendors have re-used this vid:pid for other types of
firmware, emulating FTDI chips. Attempting to continue to
support such devices without breaking class based
applications that by matching on interface
class/subclass/proto being ff/ff/00. I have no information
about the actual device or interface descriptors, but this
will at least make the proper CDC ACM devices work again.
Anyone having details of the offending device's descriptors
should update this entry with the details.
Reported-by: Florian Wöhrl <fw@woehrl.biz>
Reported-by: Xiaofan Chen <xiaofanc@gmail.com>
Cc: stable <stable@vger.kernel.org>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull drm fixes from Dave Airlie:
"Just noticed I hadn't send these out, nothing majorly urgent, I know
AMD guys have some regression fixes coming soon.
This contains:
2 nouveau fixes so it loads on the retina MBP systems properly,
2 vmwgfx fixes to load the driver earlier, and allow distros config it
1 error->debug fix in ast
and Keith was playing with 32-on-64 and decided we may as well stick
the compat ioctl in all the drivers. It fixes udl for him."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/vmwgfx: add MODULE_DEVICE_TABLE so vmwgfx loads at boot
drm/vmwgfx: allow a kconfig option to choose if fbcon is enabled
drm: use drm_compat_ioctl for 32-bit apps
drm/ast: drop debug level on error printk
drm/nv50-/gpio: initialise to vbios defaults during init
drm/nvd0/disp: hopefully fix selection of 6/8bpc mode on DP outputs
The dereference should be moved below the NULL test.
spatch with a semantic match is used to found this.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
kdump can be interrupted by watchdog timer when the timer is left
activated on the crash kernel. Changed the hpwdt driver to disable
watchdog timer at boot-time. This assures that watchdog timer is
disabled until /dev/watchdog is opened, and prevents watchdog timer
to be left running on the crash kernel.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Tested-by: Lisa Mitchell <lisa.mitchell@hp.com>
Signed-off-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@vger.kernel.org>
EHRPWM hardware supports 2 independent PWM channels. However the device
uses only one register to handle period setting for both channels. So
both channels should be configured for same period (in nsec).
Fix the same by returning error for conflicting period values.
However, allow
1. Configuration of period settings if not conflicting with other
channels
2. Re-configuring of period settings if no other channels being
configured
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
APWM mode is enabled while configuring PWM device. This was done to
handle shadow & immediate mode update of period and compare registers.
However, leaving it enabled after configuring will cause APWM output on
PWM pin even before enabling PWM device.
Fix the same by disabling APWM mode after configuring if PWM device is
not running.
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
The dereference should be moved below the NULL test.
spatch with a semantic match is used to found this.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
If kernel is compiled with CONFIG_PROVE_LOCKING the
validator raises an error when a multiplexer is removed
via sysfs and sub-clients are connected to it. This is a
false positive.
Documentation/lockdep-design.txt recommends to handle this
via calls to mutex_lock_nested().
Based on an earlier fix from Michael Lawnick.
Note that the extra code resolves to nothing unless
CONFIG_DEBUG_LOCK_ALLOC=y.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Michael Lawnick <ml.lawnick@gmx.de>
This patch adds config I2C_DESIGNWARE_CORE in Kconfig, and let
I2C_DESIGNWARE_PLATFORM and I2C_DESIGNWARE_PCI select I2C_DESIGNWARE_CORE.
Because both I2C_DESIGNWARE_PLATFORM and I2C_DESIGNWARE_PCI can be built as
built-in or module, we also need to export the functions in i2c-designware-core.
This fixes below build error when CONFIG_I2C_DESIGNWARE_PLATFORM=y &&
CONFIG_I2C_DESIGNWARE_PCI=y:
LD drivers/i2c/busses/built-in.o
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_clear_int':
i2c-designware-core.c:(.text+0xa10): multiple definition of `i2c_dw_clear_int'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x928): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_init':
i2c-designware-core.c:(.text+0x178): multiple definition of `i2c_dw_init'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x90): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `dw_readl':
i2c-designware-core.c:(.text+0xe8): multiple definition of `dw_readl'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x0): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_isr':
i2c-designware-core.c:(.text+0x724): multiple definition of `i2c_dw_isr'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x63c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_xfer':
i2c-designware-core.c:(.text+0x4b0): multiple definition of `i2c_dw_xfer'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x3c8): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_is_enabled':
i2c-designware-core.c:(.text+0x9d4): multiple definition of `i2c_dw_is_enabled'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8ec): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `dw_writel':
i2c-designware-core.c:(.text+0x124): multiple definition of `dw_writel'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x3c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_xfer_msg':
i2c-designware-core.c:(.text+0x2e8): multiple definition of `i2c_dw_xfer_msg'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x200): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_enable':
i2c-designware-core.c:(.text+0x9c8): multiple definition of `i2c_dw_enable'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8e0): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_read_comp_param':
i2c-designware-core.c:(.text+0xa24): multiple definition of `i2c_dw_read_comp_param'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x93c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_disable':
i2c-designware-core.c:(.text+0x9dc): multiple definition of `i2c_dw_disable'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8f4): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_func':
i2c-designware-core.c:(.text+0x710): multiple definition of `i2c_dw_func'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x628): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_disable_int':
i2c-designware-core.c:(.text+0xa18): multiple definition of `i2c_dw_disable_int'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x930): first defined here
make[3]: *** [drivers/i2c/busses/built-in.o] Error 1
make[2]: *** [drivers/i2c/busses] Error 2
make[1]: *** [drivers/i2c] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Jiri Slaby <jslaby@suse.cz>
Cc: stable@vger.kernel.org [3.2+]
Add the SMBus Device IDs for the Intel Lynx Point-LP PCH.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Pull DMA-mapping fixes from Marek Szyprowski:
"Another set of fixes for ARM dma-mapping subsystem.
Commit e9da6e9905 replaced custom consistent buffer remapping code
with generic vmalloc areas. It however introduced some regressions
caused by limited support for allocations in atomic context. This
series contains fixes for those regressions.
For some subplatforms the default, pre-allocated pool for atomic
allocations turned out to be too small, so a function for setting its
size has been added.
Another set of patches adds support for atomic allocations to
IOMMU-aware DMA-mapping implementation.
The last part of this pull request contains two fixes for Contiguous
Memory Allocator, which relax too strict requirements."
* 'fixes-for-3.6' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: dma-mapping: IOMMU allocates pages from atomic_pool with GFP_ATOMIC
ARM: dma-mapping: Introduce __atomic_get_pages() for __iommu_get_pages()
ARM: dma-mapping: Refactor out to introduce __in_atomic_pool
ARM: dma-mapping: atomic_pool with struct page **pages
ARM: Kirkwood: increase atomic coherent pool size
ARM: DMA-Mapping: print warning when atomic coherent allocation fails
ARM: DMA-Mapping: add function for setting coherent pool size from platform code
ARM: relax conditions required for enabling Contiguous Memory Allocator
mm: cma: fix alignment requirements for contiguous regions
This thing is killing lockdep.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
[Jani: move the init next to the other spin lock inits]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
spatch with a semantic match is used to found this.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Pull HID updates from Jiri Kosina:
"It contains a fix for Eaton Ellipse MAX UPS from Alan Stern,
performance improvement (not processing debug data if noone is
interested), by Henrik Rydberg, and allowing tpkbd-driven devices to
work even with generic driver in a crippled mode, by Andres Freund."
* 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
HID: Only dump input if someone is listening
HID: add NOGET quirk for Eaton Ellipse MAX UPS
John W. Linville says:
====================
Please pull these fixes intended for 3.6. There are more commits
here than I would like -- I got a bit behind while I was stalking
Steven Rostedt in San Diego last week... I'll slow it down after this!
There are a couple of pulls here. One is from Johannes:
"Please pull (according to the below information) to get a few fixes.
* a fix to properly disconnect in the driver when authentication or
association fails
* a fix to prevent invalid information about mesh paths being reported
to userspace
* a memory leak fix in an nl80211 error path"
The other comes via Gustavo:
"A few updates for the 3.6 kernel. There are two btusb patches to add
more supported devices through the new USB_VENDOR_AND_INTEFACE_INFO()
macro and another one that add a new device id for a Sony Vaio laptop,
one fix for a user-after-free and, finally, two patches from Vinicius
to fix a issue in SMP pairing."
Along with those...
Arend van Spriel provides a fix for a use-after-free bug in brcmfmac.
Daniel Drake avoids a hang by not trying to touch the libertas hardware
duing suspend if it is already powered-down.
Felix Fietkau provides a batch of ath9k fixes that adress some
potential problems with power settings, as well as a fix to avoid a
potential interrupt storm.
Gertjan van Wingerde provides a register-width fix for rt2x00, and
a rt2x00 fix to prevent incorrectly detecting the rfkill status.
He also provides a device ID patch.
Hante Meuleman gives us three brcmfmac fixes, one that properly
initializes a command structure, one that fixes a race condition that
could lose usb requests, and one that removes some log spam.
Marc Kleine-Budde offers an rt2x00 fix for a voltage setting on some
specific devices.
Mohammed Shafi Shajakhan sent an ath9k fix to avoid a crash related to
using timers that aren't allocated when 2 wire bluetooth coexistence
hardware is in use.
Sergei Poselenov changes rt2800usb to do some validity checking for
received packets, avoiding crashes on an ARM Soc.
Stone Piao gives us an mwifiex fix for an incorrectly set skb length
value for a command buffer.
All of these are localized to their specific drivers, and relatively
small. The power-related patches from Felix are bigger than I would
like, but I merged them in consideration of their isolation to ath9k
and the sensitive nature of power settings in wireless devices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that spc_emulate_request_sense has been taught to process zero-length
REQUEST SENSE correctly, drop the special handling of unit attention
conditions from transport_generic_new_cmd. However, for now REQUEST SENSE
will be the only command that goes through emulation for zero lengths.
(nab: Fix up zero-length check in transport_generic_new_cmd)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Similar to INQUIRY and MODE SENSE, construct the sense data in a
buffer and later copy it to the scatterlist. Do not do anything,
but still clear a pending unit attention condition, if the allocation
length is zero.
However, SPC tells us that "If a REQUEST SENSE command is terminated with
CHECK CONDITION status [and] the REQUEST SENSE command was received on
an I_T nexus with a pending unit attention condition (i.e., before the
device server reports CHECK CONDITION status), then the device server
shall not clear the pending unit attention condition." Do the
transport_kmap_data_sg early to detect this case.
It also tells us "Device servers shall not adjust the additional sense
length to reflect truncation if the allocation length is less than the
sense data available", so do not do that! Note that the err variable
is write-only.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In order to support zero-size allocation lengths, do not assert
that we have a scatterlist until after checking cmd->data_length.
But once we do this, we can have two cases of transport_kmap_data_sg
returning NULL: a zero-size allocation length, or an out-of-memory
condition. Report the latter using sense codes, so that the SCSI
command that triggered it will fail.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
SPC says:
"The ALLOCATION LENGTH field is defined in 4.3.5.6. The allocation length
should be at least 16. Device servers compliant with SPC return CHECK
CONDITION status, with the sense key set to ILLEGAL REQUEST, and the
additional sense code set to INVALID FIELD IN CDB when the allocation
length is less than 16 bytes".
Testcase: sg_raw -r8 /dev/sdb a0 00 00 00 00 00 00 00 00 08 00 00
should fail with ILLEGAL REQUEST / INVALID FIELD IN CDB sense
does not fail without the patch
fails correctly with the patch
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Several places were not checking that the parameter list length
was large enough, and thus accessing invalid memory. Zero-length
parameter lists are just a special case of this.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Right now, commands with a zero-size payload are skipped completely.
This is wrong; such commands should be passed down to the device and
processed normally.
For physical backends, this ignores completely things such as START
STOP UNIT. For virtual backends, we have a hack in place to clear a
unit attention state on a zero-size REQUEST SENSE, but we still do
not report errors properly on zero-length commands---out-of-bounds
0-block reads and writes, too small parameter list lengths, etc.
This patch fixes this for PSCSI. Uses of transport_kmap_data_sg are
guarded with a check for non-zero cmd->data_length; for all other
commands a zero length is handled properly in pscsi_execute_cmd.
The sole exception will be for now REPORT LUNS, which is handled
through the normal SPC emulation.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
It doesn't seem this spinlock was properly initialized.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If mlx4_cmd_init() failed, the init_one function returned
success, although no resources were opened.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The order of operations was wrong on the teardown flow.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The search for promisc entries was always done on the first port,
While the addition is done on the correct port.
This lead to resource leackage of promisc entries on the second
port and brought to a state where we could no longer enter to
promiscuous mode after enough iterations of "ifconfig promisc"
on the second port.
Fix that by using the correct port when searching.
Reported-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since VFs may be mapped to VMs which aren't trusted entities, flow
steering rules attached through the wrapper on behalf of VFs must be
checked to make sure that their L2 specification relate to MAC address
assigned to that VF, and add L2 specification if its missing.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To allow for usage of the flow steering Firmware structures in more locations over the driver,
such as the resource tracker, move them from mcg.c to common header files.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's a rather big set of fixes for v3.6-rc4.
There are some fixes for bugs which have been pending for a long
time and only now were uncovered, like the musb and dwc3 patches.
We have some remaining fixes for the ep->desc patch series from
Ido, a fix for renesas DMA usage, IRQ check on musb's DMA and
an oops fix on musb Host implementation.
All patches have been pending on linux-usb for a long time and
shouldn't cause any further regressions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=F4Vw
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into work-linus
usb: fixes for v3.6-rc4
Here's a rather big set of fixes for v3.6-rc4.
There are some fixes for bugs which have been pending for a long
time and only now were uncovered, like the musb and dwc3 patches.
We have some remaining fixes for the ep->desc patch series from
Ido, a fix for renesas DMA usage, IRQ check on musb's DMA and
an oops fix on musb Host implementation.
All patches have been pending on linux-usb for a long time and
shouldn't cause any further regressions.
c1dcad2d32 added a new driver configured by
HID_LENOVO_TPKBD but made the hid_have_special_driver entry non-optional which
lead to a recognized but non-working device if the new driver wasn't
configured (which is the correct default).
Signed-off-by: Andres Freund <andres@anarazel.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This will cause udev to load vmwgfx instead of waiting for X
to do it.
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
* Fix for TLB flushing introduced in v3.6
* Fix Xen-SWIOTLB not using proper DMA mask - device had 64bit but
in a 32-bit kernel we need to allocate for coherent pages from a
32-bit pool.
* When trying to re-use P2M nodes we had a one-off error and triggered
a BUG_ON check with specific CONFIG_ option.
* When doing FLR in Xen-PCI-backend we would first do FLR then save the
PCI configuration space. We needed to do it the other way around.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQSS7TAAoJEFjIrFwIi8fJOBQH/03JBKBbFvewhop8T5Jww2c9
SWmMgzDm5HkxeWj5XnM+zlLoHrYFFu7tyuRLiny4weE0LdRl4adJ1TVpStxap/b6
MSQKe+tZevslaReBOsMpbCk3z7fEWNlAcpm6wMp1xYmLoHcr0JMpOCmzigbf7dwM
F4UWULheih9ME3UeqDAU8qgvfv6ccZ9vempO4TDWKjxfxfWODCNMRx+Ny+C7NNRk
QeoInHJUqcRkg0q0OIciF/YYDmn8hIH7HgfqomuMb6rEv2LOieLnWVuniEPWM75s
lECxro7v2Z9s1Std0WWKcFp8VZpI2scnQYU8aL8TpewHcbzKHQYyipuKPu7FiEQ=
=GfLE
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.6-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
* Fix for TLB flushing introduced in v3.6
* Fix Xen-SWIOTLB not using proper DMA mask - device had 64bit but
in a 32-bit kernel we need to allocate for coherent pages from a
32-bit pool.
* When trying to re-use P2M nodes we had a one-off error and triggered
a BUG_ON check with specific CONFIG_ option.
* When doing FLR in Xen-PCI-backend we would first do FLR then save the
PCI configuration space. We needed to do it the other way around.
* tag 'stable/for-linus-3.6-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pciback: Fix proper FLR steps.
xen: Use correct masking in xen_swiotlb_alloc_coherent.
xen: fix logical error in tlb flushing
xen/p2m: Fix one-off error in checking the P2M tree directory.
Power management
- PCI/PM: Enable D3/D3cold by default for most devices
- PCI/PM: Keep parent bridge active when probing device
- PCI/PM: Fix config reg access for D3cold and bridge suspending
- PCI/PM: Add ABI document for sysfs file d3cold_allowed
Core
- PCI: Don't print anything while decoding is disabled
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=zFNa
-----END PGP SIGNATURE-----
Merge tag '3.6-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Power management
- PCI/PM: Enable D3/D3cold by default for most devices
- PCI/PM: Keep parent bridge active when probing device
- PCI/PM: Fix config reg access for D3cold and bridge suspending
- PCI/PM: Add ABI document for sysfs file d3cold_allowed
Core
- PCI: Don't print anything while decoding is disabled"
* tag '3.6-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Don't print anything while decoding is disabled
PCI/PM: Add ABI document for sysfs file d3cold_allowed
PCI/PM: Fix config reg access for D3cold and bridge suspending
PCI/PM: Keep parent bridge active when probing device
PCI/PM: Enable D3/D3cold by default for most devices
In 3.6-rc3, without this patch, the following error occurs with a modular build:
ERROR: "gen_split_key" [drivers/crypto/caam/caamhash.ko] undefined!
ERROR: "gen_split_key" [drivers/crypto/caam/caamalg.ko] undefined!
Signed-off-by: Ben Collins <ben.c@servergy.com>
Cc: Yuan Kang <Yuan.Kang@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Mostly Renesas and Atmel bugfixes this time, targeting boot and build
problems. A couple of patches for gemini and kirkwood as well. On a
whole nothing very controversial.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=hMrY
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC bug fixes from Olof Johansson:
"Mostly Renesas and Atmel bugfixes this time, targeting boot and build
problems. A couple of patches for gemini and kirkwood as well. On a
whole nothing very controversial."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: gemini: fix the gemini build
ARM: shmobile: armadillo800eva: enable rw rootfs mount
ARM: Kirkwood: Fix 'SZ_1M' undeclared here for db88f6281-bp-setup.c
ARM: shmobile: mackerel: fixup usb module order
ARM: shmobile: armadillo800eva: fixup: sound card detection order
ARM: shmobile: marzen: fixup smsc911x id for regulator
ARM: at91/feature-removal-schedule: delay at91_mci removal
ARM: mach-shmobile: armadillo800eva: Enable power button as wakeup source
ARM: mach-shmobile: armadillo800eva: Fix GPIO buttons descriptions
ARM: at91/dts: remove partial parameter in at91sam9g25ek.dts
ARM: at91/clock: fix PLLA overclock warning
ARM: at91: fix rtc-at91sam9 irq issue due to sparse irq support
ARM: at91: fix system timer irq issue due to sparse irq support
ARM: shmobile: sh73a0: fixup RELOC_BASE of intca_irq_pins_desc
If xfernotready is received and there is no request in request_list then
REQUEST_PENDING flag must be set, so that next request in ep queue is executed.
In case of isoc transfer, if xfernotready is already elapsed and even first
request has not been queued to request_list, then issue END TRANSFER, so that
you can receive xfernotready again and can have notion of current microframe.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
renesas_usbhs dma can transport 8byte alignment data, not 4byte.
This patch fixup it.
Reported-by: Sugnan Prabhu S <sugnan.prabhu@renesasmobile.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Earlier we used to check for ep->ep.desc to figure out if this ep has
already been enabled and if so, abort.
Ido Shayevitz removed the usb_endpoint_descriptor from private udc
structure 5a6506f00 ("usb: gadget: Update at91_udc to use
usb_endpoint_descriptor inside the struct usb_ep") but did not fix up
the ep_enable condition because _now_ the member is always true and we
can't check if this ep is enabled twice.
Cc: Ido Shayevitz <idos@codeaurora.org>
Tested-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Tested-by: Mario Isidoro <Mario.Isidoro@tecmic.pt>
Cc: <stable@kernel.org> # v3.5
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The driver was converted to the new start/stop interface in f3d8bf34c2
("usb: gadget: at91_udc: convert to new style start/stop interface").
I overlooked that the driver is overwritting the private data which is
used by the composite framework. The udc driver doesn't read it, it is
only written here.
Tested-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Tested-by: Mario Isidoro <Mario.Isidoro@tecmic.pt>
Cc: <stable@kernel.org> # v3.5
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Populate the resources for xhci afresh instead of directly using the
*struct resource* of core. *resource* structure has parent, sibling,
child pointers which should be filled only by resource API's. By
directly using the *resource* pointer of core in xhci, these parent,
sibling, child pointers are already populated even before
*platform_device_add* causing side effects.
Cc: stable@vger.kernel.org # v3.4, v3.5
Reported-by: Ruchika Kharwar <ruchika@ti.com>
Tested-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dma_controller_create() in this MUSB DMA driver only regards 0 as a wrong IRQ
number, despite platform_get_irq_byname() that it calls returns -ENXIO in that
case. It leads to calling request_irq() with a negative IRQ number, and when it
naturally fails, the following is printed to the console:
request_irq -6 failed!
and the DMA controller is not created.
Fix this function to filter out the error values as well as 0.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On platform_device_add() failure, the TUSB6010 glue layer forgets to call
platform_device_put() -- probably due to a typo...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
when using musb_urb_enqueue to submit three urbs to the same endpoint, when
hep->hcpriv is NULL, qh will be allocated when the first urb is completed.
When the IRQ completes the next two urbs, qh->hep->hcpriv will be set to NULL.
Now the second urb get musb->lock and executes musb_schedule(), but
next_urb(qh) is NULL, so musb_start_urb will Oops.
[ balbi@ti.com : practically rewrote commit log so it makes sense ]
Signed-off-by: mayuzheng <myz147@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Without a reply for USB_DT_BOS the USB3 mode does not work since
448b6eb1 ("USB: Make sure to fetch the BOS desc for roothubs.).
Cc: stable@vger.kernel.org #v3.5
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If USB2 host controller probes fine but USB3 does not then we don't
remove the USB controller properly and lock up the system while the HUB
code will try to enumerate the USB2 controller and access memory which
is no longer available in case the dummy_hcd was compiled as a module.
This is a problem since 448b6eb1 ("USB: Make sure to fetch the BOS desc
for roothubs.) if used in USB3 mode because dummy does not provide this
descriptor and explodes later.
Cc: stable@vger.kernel.org # v3.5
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert a 0 error return code to a negative one, as returned elsewhere in the
function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@
(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
when != ret = e3
*if (x == NULL || ...)
{
... when != ret = e4
* return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case of ep0 out, if length is not aligned to maxpacket size then we use
dwc->ep_bounce_addr for dma transfer and not request->dma. Since, we have
alreday done memcpy from dwc->ep0_bounce to request->buf, so we do not need to
issue cache sync function. In fact, cache sync function will bring wrong data
in request->buf from request->dma in this scenario.
So, cache sync function must not be executed in case of ep0 bounced.
Cc: <stable@vger.kernel.org> # v3.4 v3.5
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If f_fs.c and u_serial.c are combined together using #include, which has
been a common practice so far, the pr_vdebug macro is defined multiple
times. Define it only once.
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When we do FLR and save PCI config we did it in the wrong order.
The end result was that if a PCI device was unbind from
its driver, then binded to xen-pciback, and then back to its
driver we would get:
> lspci -s 04:00.0
04:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
13:42:12 # 4 :~/
> echo "0000:04:00.0" > /sys/bus/pci/drivers/pciback/unbind
> modprobe e1000e
e1000e: Intel(R) PRO/1000 Network Driver - 2.0.0-k
e1000e: Copyright(c) 1999 - 2012 Intel Corporation.
e1000e 0000:04:00.0: Disabling ASPM L0s L1
e1000e 0000:04:00.0: enabling device (0000 -> 0002)
xen: registering gsi 48 triggering 0 polarity 1
Already setup the GSI :48
e1000e 0000:04:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
e1000e: probe of 0000:04:00.0 failed with error -2
This fixes it by first saving the PCI configuration space, then
doing the FLR.
Reported-by: Ren, Yongjie <yongjie.ren@intel.com>
Reported-and-Tested-by: Tobias Geiger <tobias.geiger@vido.info>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: stable@vger.kernel.org
Make sure that the cdev pointer for IO subchannels is set to NULL when
we deregister the device (and release its last reference). This will
fix a bug were another process operates on an already freed ccw device.
Acked-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the subchannel event function is called from IRQ context and we
observe that the subchannel in question is gone we flag the attached
device as not operational and schedule the event function to be called
again from process context where the subchannel gets deregistered.
However if the subchannel reappeared at the time the event function
gets called from process context we would do nothing and leave the
device in not operational state. Recognize this case in sch_get_action
and trigger reexamination of the subchannel/device.
Acked-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Ensure that all work is done when the process waiting for a
dasd state change is woken up. With this change it is save
to assume that after a userspace triggered state change and
a udev settle invocation there are no unexpected users of a
dasd device.
Acked-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
- a firmware bug on several Samsung MoviNAND eMMC models causes
permanent corruption on the device when secure erase and secure trim
requests are made, so we disable those requests on these eMMC devices.
- atmel-mci: fix a hang with some SD cards by waiting for not-busy flag.
- dw_mmc: low-power mode breaks SDIO interrupts; fix PIO error handling;
fix handling of error interrupts.
- mxs-mmc: fix deadlocks; fix compile error due to dma.h arch change.
- omap: fix broken PIO mode causing memory corruption.
- sdhci-esdhc: fix card detection.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=n1hi
-----END PGP SIGNATURE-----
Merge tag 'mmc-fixes-for-3.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC fixes from Chris Ball:
- a firmware bug on several Samsung MoviNAND eMMC models causes
permanent corruption on the device when secure erase and secure trim
requests are made, so we disable those requests on these eMMC devices.
- atmel-mci: fix a hang with some SD cards by waiting for not-busy flag.
- dw_mmc: low-power mode breaks SDIO interrupts; fix PIO error handling;
fix handling of error interrupts.
- mxs-mmc: fix deadlocks; fix compile error due to dma.h arch change.
- omap: fix broken PIO mode causing memory corruption.
- sdhci-esdhc: fix card detection.
* tag 'mmc-fixes-for-3.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: omap: fix broken PIO mode
mmc: card: Skip secure erase on MoviNAND; causes unrecoverable corruption.
mmc: dw_mmc: Disable low power mode if SDIO interrupts are used
mmc: dw_mmc: fix error handling in PIO mode
mmc: dw_mmc: correct mishandling error interrupt
mmc: dw_mmc: amend using error interrupt status
mmc: atmel-mci: not busy flag has also to be used for read operations
mmc: sdhci-esdhc: break out early if clock is 0
mmc: mxs-mmc: fix deadlock caused by recursion loop
mmc: mxs-mmc: fix deadlock in SDIO IRQ case
mmc: bfin_sdh: fix dma_desc_array build error
Allocate a structure not a pointer to it !
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Erroneous debug message from of_get_named_gpio_flags()
- Make sure the MC9S08DZ60 GPIO driver depend on I2C being
compiled in (not module) or allmodconfig breaks.
- Check return value from irq_alloc_descs() in the Emma
Mobile GPIO driver.
- Assign the owner field for the rdc321x driver so the
module won't be removed if it has active GPIOs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=QDOR
-----END PGP SIGNATURE-----
Merge tag 'gpio-fixes-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"These are some GPIO regression fixes for v3.6:
- Erroneous debug message from of_get_named_gpio_flags()
- Make sure the MC9S08DZ60 GPIO driver depend on I2C being compiled
in (not module) or allmodconfig breaks.
- Check return value from irq_alloc_descs() in the Emma Mobile GPIO
driver.
- Assign the owner field for the rdc321x driver so the module won't
be removed if it has active GPIOs."
* tag 'gpio-fixes-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: rdc321x: Prevent removal of modules exporting active GPIOs
gpio: em: Fix checking return value of irq_alloc_descs
gpio: mc9s08dz60: Fix build error if I2C=m
gpio: Fix debug message in of_get_named_gpio_flags()
- a fix by Paul Cercueil to prevent a possible buffer overflow
- a fix by Bruno Prémont to prevent a rare sleep in invalid context
- a fix by Julia Lawall for a double free in auo_k190x
- a fix by Dan Carpenter to prevent a division by zero in mb862xxfb
- a regression fix by Tomi Valkeinen for the SDI output in OMAP
- a fix by Grazvydas Ignotas to fix the console colors in OMAP
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)
iQIcBAABAgAGBQJQRdW3AAoJECSVL5KnPj1PKpcQAJn9tS3BeTi9zcV5sk31U1Jy
kc72y318bg5jpJPDgWOfM+9CY3yhezVi2q9odiTUtuhx5WzWbOJh7/TuUGoWGKaY
dUvTqen83hFGKfTs+eujTbAgAH3+PGIGo5VmTyx1TVj5Vnb1m3wsU6jwDzalfox8
MChhoOyrCpn6wxiqSuF6eoqZ01jASsNDW1rQaxi6AdaKKxJXrG22phMpwmfZz9Mt
naIx1aI8aowkZ5gEBlOsnX6O0kjPVyQWlXqljGuZxRJZD+x9MKj/8nU1PITi0Pz2
DNAQz3ZU/apAooLCFsBF7oGtMUJ6e/v61LdIcMZZzw569tCtnmidwdU0ss2JJhAP
aDhdtWESbxFbpggOEWD36Wq6Z5ekCW5xfTR+ZASiknSMAT6rmqfX4NPJ3750jjVb
Aa9Ds37KQgfUrQIEhKCoZPyPTtCK98fQUHhxlf2I0TbuCGBvbZEAnRpuc1eelNo9
G9IJKG1vnea2x+DmsR1OEqFpHU3fn82T7RYm3SYc6ZDJwU58GxEvTzytGBs5YxLe
bTTM2mTT3m23l8BBp6UPZjESJoBv2bd+cY70MCxhVIKHXbQYdzet0DDEDA6t2UQK
isIOLXMGqxTXNZq7bM+q9UuYUuAkTUv1VmwGy5YJOD1JtOhFGQtxBe59OMmrC1H5
aU+GP6btV/biv8cTs/JG
=8eFG
-----END PGP SIGNATURE-----
Merge tag 'fbdev-fixes-for-3.6-1' of git://github.com/schandinat/linux-2.6
Pull fbdev fixes from Florian Tobias Schandinat:
- a fix by Paul Cercueil to prevent a possible buffer overflow
- a fix by Bruno Prémont to prevent a rare sleep in invalid context
- a fix by Julia Lawall for a double free in auo_k190x
- a fix by Dan Carpenter to prevent a division by zero in mb862xxfb
- a regression fix by Tomi Valkeinen for the SDI output in OMAP
- a fix by Grazvydas Ignotas to fix the console colors in OMAP
* tag 'fbdev-fixes-for-3.6-1' of git://github.com/schandinat/linux-2.6:
OMAPFB: fix framebuffer console colors
OMAPDSS: Fix SDI PLL locking
video: mb862xxfb: prevent divide by zero bug
drivers/video/auo_k190x.c: drop kfree of devm_kzalloc's data
fbcon: Fix bit_putcs() call to kmalloc(s, GFP_KERNEL)
fbcon: prevent possible buffer overflow.
'kmem_cache_alloc()' but were freeing it using 'kfree()' in some cases.
Now we fix this by using 'kmem_cache_free()' instead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Bin1
-----END PGP SIGNATURE-----
Merge tag 'upstream-3.6-rc5' of git://git.infradead.org/linux-ubi
Pull ubi fix from Artem Bityutskiy:
"A single small fix for memory deallocation: we allocated memory using
'kmem_cache_alloc()' but were freeing it using 'kfree()' in some
cases. Now we fix this by using 'kmem_cache_free()' instead."
* tag 'upstream-3.6-rc5' of git://git.infradead.org/linux-ubi:
UBI: fix a horrible memory deallocation bug
Hi Greg,
Here's seven bugfixes for 3.6. All of them are marked for stable, and
most are vendor-specific fixes.
Details:
--------
- Commits 052c7f9 and 2963657 fix a couple stupid mistakes I made in a
Intel xHCI bug fix patch I pushed just before I left for vacation.
- Commits 29d2145 and a96874a fix issues with the Intel Panther Point
EHCI to xHCI port switchover.
- Commit 71c731a adds the work-around for the TI redriver "dead port"
issue.
- Commit 319acdf adds a fix for non-PCI xHCI platform drivers.
- Commit e955a1c works around the UEFI issue with the xHCI host
sometimes returning 0xff's in the MMIO on boot.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=124d
-----END PGP SIGNATURE-----
Merge tag 'for-usb-linus-2012-09-05' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
xHCI 3.6 bug fixes.
Hi Greg,
Here's seven bugfixes for 3.6. All of them are marked for stable, and
most are vendor-specific fixes.
Details:
--------
- Commits 052c7f9 and 2963657 fix a couple stupid mistakes I made in a
Intel xHCI bug fix patch I pushed just before I left for vacation.
- Commits 29d2145 and a96874a fix issues with the Intel Panther Point
EHCI to xHCI port switchover.
- Commit 71c731a adds the work-around for the TI redriver "dead port"
issue.
- Commit 319acdf adds a fix for non-PCI xHCI platform drivers.
- Commit e955a1c works around the UEFI issue with the xHCI host
sometimes returning 0xff's in the MMIO on boot.
Sarah Sharp
The pointer to the sense buffer is fetched by transport_get_sense_data,
but this is called by target_complete_ok_work long after pscsi_req_done
has freed the struct that contains it.
Pass instead the fabric's sense buffer to transport_complete,
and copy the data to it directly in transport_complete. Setting
SCF_TRANSPORT_TASK_SENSE also becomes a duty of transport_complete.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The error conditions in transport_get_sense_data are superfluous
and complicate the code unnecessarily:
* SCF_TRANSPORT_TASK_SENSE is checked in the caller;
* it's simply part of the invariants of dev->transport->get_sense_buffer
that it must be there if transport_complete ever returns 1, and that
it must not return NULL. Besides, the entire callback will disappear
with the next patch.
* similarly in the caller we can expect that sense data is only sent
for non-zero cmd->scsi_status.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We will be calling it from transport_complete_cmd, avoid forward
declarations. No semantic change.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch (as1604) adds a CONFIG_INTF_STRINGS quirk for the Joss
infrared touchboard device. The device doesn't like to be asked for
its interface strings.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: adam ? <adam3337@wp.pl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the number of ports present on the SoC/board is not the maximum
and that the platform data is not filled with all data, there is
an easy way to mess the PIO setup for this interface.
This quick fix addresses mis-configuration in USB host platform data
that is common in at91 boards since commit 0ee6d1e (USB: ohci-at91:
change maximum number of ports) that did not modified the associatd
board files.
Reported-by: Klaus Falkner <klaus.falkner@solectrix.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Stable <stable@vger.kernel.org> [3.4+]
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the USB PID for the NZR SEM 16+ USB energy monitor device
<http://www.nzr.de>. It works perfectly with the GPL software on
<http://schou.dk/linux/sparometer/>.
Signed-off-by: Horst Schirmeier <horst@schirmeier.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b69cc67205 added support for the E-861. After acquiring a C-867, I
realised that every Physik Instrumente's device has a different PID. They are
listed in the Windows device driver's .inf file. So here are all PIDs for the
current (and probably future) USB devices from Physik Instrumente.
Compiled, but only actually tested on the E-861 and C-867.
Signed-off-by: Éric Piel <piel@delmic.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a bug found by Nish Aravamudan
(https://lkml.org/lkml/2012/5/15/220) where the driver is not following
the spec (it is not aligning the rx buffer on a 16-byte boundary) and the
hypervisor aborts the registration, making the device unusable.
The fix follows BenH's recommendation (https://lkml.org/lkml/2012/7/20/461)
to replace the kmalloc+map for a single call to dma_alloc_coherent()
because that function always aligns to a 16-byte boundary.
The stable trees will run into this bug whenever the rx buffer kmalloc call
returns something not aligned on a 16-byte boundary.
Cc: <stable@vger.kernel.org>
Signed-off-by: Santiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the DRM drivers appear to be missing the .compat_ioctl file
operation entry necessary for 32-bit application compatibility.
This patch uses drm_compat_ioctl for all drivers which don't have
their own, and which are using drm_ioctl for .unlocked_ioctl.
This leaves drivers/gpu/drm/psb/psb_drv.c unchanged; it has a custom
.unlocked_ioctl and will presumably need a custom .compat_ioctl as
well.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Remove the clock configuration from imx_setup_ufcr(). This
isn't needed here and will cause garbage output if done.
To be be sure that we only touch the bits we want (TXTL and RXTL)
we have to mask out all other bits of the UFCR register. Add
one non-existing bit macro for this, too (bit 6, DCEDTE on i.MX6).
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Shawn Guo <shawn.guo@linaro.org>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Xinyu Chen <xinyu.chen@freescale.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The console feature's write routing is unsafe on SMP with
the startup/shutdown call.
There could be several consumers of the console
* the kernel printk
* the init process using /dev/kmsg to call printk to show log
* shell, which open /dev/console and write with sys_write()
The shell goes into the normal uart open/write routing,
but the other two go into the console operations.
The open routing calls imx serial startup, which will write USR1/2
register without any lock and critical with imx_console_write call.
Add a spin_lock for startup/shutdown/console_write routing.
This patch is a port from Freescale's Android kernel.
Signed-off-by: Xinyu Chen <xinyu.chen@freescale.com>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For non PCI-based stacks, this function call
usb_disable_xhci_ports(to_pci_dev(hcd->self.controller));
made from xhci_shutdown is not applicable.
Ideally, we wouldn't have any PCI-specific code on
a generic driver such as the xHCI stack, but it looks
like we should just stub usb_disable_xhci_ports() out
for non-PCI devices.
[ balbi@ti.com: slight improvement to commit log ]
This patch should be backported to kernels as old as 3.0, since the
commit it fixes (e95829f474 "xhci: Switch
PPT ports to EHCI on shutdown.") was marked for stable.
Signed-off-by: Moiz Sonasath<m-sonasath@ti.com>
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Marc Kleine-Budde says:
====================
this patch is for the v3.6 release cycle. Benoît Locher fixed a repeated frame
bug in the mcp251x driver. He implemented the workaround suggested by the
errata sheet.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the ioremap_nocache variant of the ioremap API in
order to make sure our memory will be marked uncachable.
This patch should be backported to kernels as old as 3.4, that contain
the commit 3429e91a66 "usb: host: xhci:
add platform driver support".
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
This patch is intended to work around a known issue on the
SN65LVPE502CP USB3.0 re-driver that can delay the negotiation
between a device and the host past the usual handshake timeout.
If that happens on the first insertion, the host controller
port will enter in Compliance Mode and NO port status event will
be generated (as per xHCI Spec) making impossible to detect this
event by software. The port will remain in compliance mode until
a warm reset is applied to it.
As a result of this, the port will seem "dead" to the user and no
device connections or disconnections will be detected.
For solving this, the patch creates a timer which polls every 2
seconds the link state of each host controller's port (this
by reading the PORTSC register) and recovers the port by issuing a
Warm reset every time Compliance mode is detected.
If a xHC USB3.0 port has previously entered to U0, the compliance
mode issue will NOT occur only until system resumes from
sleep/hibernate, therefore, the compliance mode timer is stopped
when all xHC USB 3.0 ports have entered U0. The timer is initialized
again after each system resume.
Since the issue is being caused by a piece of hardware, the timer
will be enabled ONLY on those systems that have the SN65LVPE502CP
installed (this patch uses DMI strings for detecting those systems)
therefore making this patch to act as a quirk (XHCI_COMP_MODE_QUIRK
has been added to the xhci stack).
This patch applies for these systems:
Vendor: Hewlett-Packard. System Models: Z420, Z620 and Z820.
This patch should be backported to kernels as old as 3.2, as that was
the first kernel to support warm reset. The kernels will need to
contain both commit 10d674a82e "USB: When
hot reset for USB3 fails, try warm reset" and commit
8bea2bd37d "usb: Add support for root hub
port status CAS". The first patch add warm reset support, and the
second patch modifies the USB core to issue a warm reset when the port
is in compliance mode.
Signed-off-by: Alexis R. Cortes <alexis.cortes@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
My test platform (Intel DX79SI) boots reliably under BIOS, but frequently
crashes when booting via UEFI. I finally tracked this down to the xhci
handoff code. It seems that reads from the device occasionally just return
0xff, resulting in xhci_find_next_cap_offset generating a value that's
larger than the resource region. We then oops when attempting to read the
value. Sanity checking that value lets us avoid the crash.
I've no idea what's causing the underlying problem, and xhci still doesn't
actually *work* even with this, but the machine at least boots which will
probably make further debugging easier.
This should be backported to kernels as old as 2.6.31, that contain the
commit 66d4eadd8d "USB: xhci: BIOS handoff
and HW initialization."
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
The intent was to test whether the flag was set.
This patch should be backported to stable kernels as old as 3.0, since
it fixes a bug in commit e95829f474 "xhci:
Switch PPT ports to EHCI on shutdown.", which was marked for stable.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
This patch fixes a race condition that results in memory
corruption when using cleancache.
The race exists between the zcache shrinker handler,
shrink_zcache_memory() and cleancache_get_page().
In most cases, the shrinker will both evict a zbpg
from its buddy list and flush it from tmem before a
cleancache_get_page() occurs on that page. A subsequent
cleancache_get_page() will fail in the tmem layer.
In the rare case that two occur together and the
cleancache_get_page() path gets through the tmem
layer before the shrinker path can flush tmem,
zbud_decompress() does a check to see if the zbpg is a
"zombie", i.e. not on a buddy list, which means the shrinker
is in the process of reclaiming it. If the zbpg is a zombie,
zbud_decompress() returns -EINVAL.
However, this return code is being ignored by the caller,
zcache_pampd_get_data_and_free(), which results in the
caller of cleancache_get_page() thinking that the page has
been properly retrieved when it has not.
This patch modifies zcache_pampd_get_data_and_free() to
convey the failure up the stack so that the caller of
cleancache_get_page() knows the page retrieval failed.
This needs to be applied to stable trees as well.
zcache-main.c was named zcache.c before v3.1, so
I'm not sure how you want to handle trees earlier
than that.
Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the interface is down, the hardware is powered off.
However, the suspend handler currently tries to send host sleep commands
(when wakeup params are set) in this configuration, causing a system hang
when going into suspend (the commands will never complete).
Avoid this by detecting this situation and simply returning from
the suspend handler without doing anything special.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On our system (ARM Cortex-M3 SOC running linux-2.6.33)
frequent crashes were observed in the rt2800usb module
because of the invalid length of the received packet (3392,
46920...). This patch adds the sanity check on the packet
legth. Also, changed WARNING to ERROR in rt2x00lib_rxdone()
so that the bad packet condition would be noticed.
The fix was tested on the latest compat-wireless-3.5.1-1-snpc.
Cc: stable@vger.kernel.org
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to program the rfkill switch GPIO pin direction to input at
device initialization time, not only when the interface is brought up.
Doing this only when the interface is brought up could lead to rfkill
detecting the switch is turned on erroneously and inability to create
the interface and bringing it up.
Reported-and-tested-by: Andreas Messer <andi@bastelmap.de>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: <stable@vger.kernel.org>
Acked-by: Ivo Van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The register is 16 bits wide, not 32.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: <stable@vger.kernel.org>
Acked-by: Ivo Van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is an RT3572 based device.
Signed-off-by: Maximilian Engelhardt <maxi@daemonizer.de>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: <stable@vger.kernel.org>
Acked-by: Ivo Van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function brcmf_cfg80211_get_station requests the RSSI from
the device. The complete structure used needs to be cleared
before sending the request to firmware. Otherwise the request
fails filling the logs with "Could not get rssi (-2)" messages.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On both rx and tx there is was a race condition on the queueing
of usb requests. When for example frame gets submitted it is
possible that complete function gets called even before
usb_submit_urb() returns. As a result it is possible that usb
requests get losts, which was noticed on OMAP4 pandaboard
platform. This patch fixes the race condition.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
URB_ZERO_PACKET should only be set or bulk OUT and this condition
is checked with a WARN_ON in usb_submit_urb(). This patch fixes
brcmfmac to get rid of this warning filling the logs.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The USB part of the brcmfmac did a dev_kfree_skb() that resulted
in a warning in net/core/skbuff.c:
Jul 11 04:53:33 lb-bun-10 kernel: [53282.667745] WARNING: at
net/core/skbuff.c:490 skb_release_head_state+0xcc/0xe0()
The brcmutil modules provides brcmu_pkt_buf_free_skb() which takes
the context into account. This patch makes use of this function
instead of dev_kfree_skb().
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This feature had been disabled in ath9k because the code to support
it was incomplete, but now the code is in sync with the internal QCA
codebase, so it's time to enable it.
On many newer devices, the calibration is assumed to be done with PA
linearization enabled.
Tests with a particular AR933x device showed that the signal emitted
at full power was highly distorted and unreliable with PA linearization
disabled. With this patch, the signal becomes clear and stability
is improved.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before PAPRD training can run, the card needs to have sent a packet for
thermal calibration. Sending a dummy packet with the PAPRD training flag
set causes a crash under some circumstance.
Fix the code by replacing the dummy tx with a delay that waits for a
real packet tx to have occurred.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Re-train if the calibrated PA linearization curve is out of bounds
(affects AR933x and AR9485).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The interrupt is no longer handling it. While it shouldn't fire (wraparound
is highly unlikely), the consequences would be fatal (interrupt storm).
Disable the interrupt to prevent that from happening.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to the vendor driver v2.6.0.1, during the rf register init the SRAM
voltage should be increased to 1.35V and after 1ms decreased back to 1.2V. This
patch adds the field setting of LDO_CFG0_LDO_CORE_VLEVEL accordingly.
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@blackshift.org>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we send a command to firmware, we assumed that cmd_size
will be always less than or equal to the structure size of
host_cmd_ds_command. However, this is no longer true after
we added AP support. There are some AP commands that Custom
IE TLVs are included in command buffer, hence the cmd_size
gets enlarged by the TLV data. We need to increase the skb
length for the extra data.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When running 32-bit pvops-dom0 and a driver tries to allocate a coherent
DMA-memory the xen swiotlb-implementation returned memory beyond 4GB.
The underlaying reason is that if the supplied driver passes in a
DMA_BIT_MASK(64) ( hwdev->coherent_dma_mask is set to 0xffffffffffffffff)
our dma_mask will be u64 set to 0xffffffffffffffff even if we set it to
DMA_BIT_MASK(32) previously. Meaning we do not reset the upper bits.
By using the dma_alloc_coherent_mask function - it does the proper casting
and we get 0xfffffffff.
This caused not working sound on a system with 4 GB and a 64-bit
compatible sound-card with sets the DMA-mask to 64bit.
On bare-metal and the forward-ported xen-dom0 patches from OpenSuse a coherent
DMA-memory is always allocated inside the 32-bit address-range by calling
dma_alloc_coherent_mask.
This patch adds the same functionality to xen swiotlb and is a rebase of the
original patch from Ronny Hegewald which never got upstream b/c the
underlaying reason was not understood until now.
The original email with the original patch is in:
http://old-list-archives.xen.org/archives/html/xen-devel/2010-02/msg00038.html
the original thread from where the discussion started is in:
http://old-list-archives.xen.org/archives/html/xen-devel/2010-01/msg00928.html
Signed-off-by: Ronny Hegewald <ronny.hegewald@online.de>
Signed-off-by: Stefano Panella <stefano.panella@citrix.com>
Acked-By: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: stable@vger.kernel.org
* commit '4cb38750d49010ae72e718d46605ac9ba5a851b4': (6849 commits)
bcma: fix invalid PMU chip control masks
[libata] pata_cmd64x: whitespace cleanup
libata-acpi: fix up for acpi_pm_device_sleep_state API
sata_dwc_460ex: device tree may specify dma_channel
ahci, trivial: fixed coding style issues related to braces
ahci_platform: add hibernation callbacks
libata-eh.c: local functions should not be exposed globally
libata-transport.c: local functions should not be exposed globally
sata_dwc_460ex: support hardreset
ata: use module_pci_driver
drivers/ata/pata_pcmcia.c: adjust suspicious bit operation
pata_imx: Convert to clk_prepare_enable/clk_disable_unprepare
ahci: Enable SB600 64bit DMA on MSI K9AGM2 (MS-7327) v2
[libata] Prevent interface errors with Seagate FreeAgent GoFlex
drivers/acpi/glue: revert accidental license-related 6b66d95895 bits
libata-acpi: add missing inlines in libata.h
i2c-omap: Add support for I2C_M_STOP message flag
i2c: Fall back to emulated SMBus if the operation isn't supported natively
i2c: Add SCCB support
i2c-tiny-usb: Add support for the Robofuzz OSIF USB/I2C converter
...
commit a1e636e6d3 (Input: imx_keypad - use clk_prepare_enable/
clk_disable_unprepare()) missed to update clk_enable/clk_disable
in imx_keypad_probe().
Fix it so that we do not get clk warnings at boot.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Certain eGalax devices expose an interface with class HID and protocol
None. Some work with usbhid and some work with usbtouchscreen, but
there is no easy way to differentiate. Sending an eGalax diagnostic
packet seems to kick them all into using the right protocol for
usbtouchscreen, so we can continue to bind them all there (as opposed to
handing some off to usbhid).
This fixes a regression for devices that were claimed by (and worked
with) usbhid prior to commit 139ebe8dc8
("Input: usbtouchscreen - fix eGalax HID ignoring"), which made
usbtouchscreen claim them instead. With this patch they will still be
claimed by usbtouchscreen, but they will actually report events
usbtouchscreen can understand. Note that these devices will be limited
to the usbtouchscreen feature set so e.g. dual touch features are not
supported.
I have the distinct pleasure of needing to support devices of both types
and have tested accordingly.
Signed-off-by: Forest Bond <forest.bond@rapidrollout.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
With a previous patch to enable the EHCI/XHCI port switching, it switches
all the available ports.
The assumption is not correct because the BIOS may expect some ports
not switchable by the OS.
There are two more registers that contains the information of the switchable
and non-switchable ports.
This patch adds the checking code for the two register so that only the
switchable ports are altered.
This patch should be backported to kernels as old as 3.0, that contain
commit ID 69e848c209 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: Keng-Yu Lin <kengyu@canonical.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
On Intel Panther Point chipset USB 3.0 devices show up as
high-speed devices on powerup, but after an s3 cycle they are
correctly recognized as SuperSpeed. At powerup switch the port
to xHCI so that USB 3.0 devices are correctly recognized.
BugLink: http://bugs.launchpad.net/bugs/1000424
This patch should be backported to kernels as old as 3.0, that contain
commit ID 69e848c209 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Fixed a bug. Data was being written to user space using an IOCTL
command encoded with _IOC_WRITE access mode.
Signed-off-by: Dae S. Kim <dae@velatum.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi,
This patch fixes a bug with driver failing to negotiate a connection.
The bug was traced to commit
203e4615ee
staging: vt6656: removed custom definitions of Ethernet packet types
In that patch, definitions in include/linux/if_ether.h replaced ones
in tether.h which had both big and little endian definitions.
include/linux/if_ether.h only refers to big endian values, cpu_to_be16
should be used for the correct endian architectures.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: stable <stable@vger.kernel.org> # 2.6.37+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"addr" is a pointer so it's either 4 or 8 bytes, but actually we want
to compare 6 bytes (ETH_ALEN).
As network stack already provides helper function
is_zero_ether_addr() we use that instead of memcmp
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Rupesh Gujare <rgujare@ozmodevices.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function pointer scan in struct cfg80211_ops is not
supposed to be assigned a function with a struct net_device
pointer as an argument. Instead access the net_device struct
in the following way:
struct net_device *dev = request->wdev->netdev;
sparse gives these warnings:
drivers/staging/wlan-ng/cfg80211.c:726:17: warning:
incorrect type in initializer (incompatible argument 2
(different base types))
expected int ( *scan )( ... )
got int ( extern [toplevel] *<noident> )( ... )
drivers/staging/wlan-ng/cfg80211.c:726:2: warning:
initialization from incompatible pointer type [enabled by default]
drivers/staging/wlan-ng/cfg80211.c:726:2: warning:
(near initialization for ‘prism2_usb_cfg_ops.scan’)
[enabled by default]
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A few simple fixes.
1)Fix up some possible divide by zero issues in various drivers.
2)Prevent a memory leak in an error path in lis3l02dq
3)Make sure the PTR_ERR call in at91_adc matches the
check for IS_ERR just above it rather than using a different
pointer.
Merges fine against v3.6rc4
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=pdyb
-----END PGP SIGNATURE-----
Merge tag 'v3.6-rc1-iio-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
IIO fixes for v3.6-rc1 set 2
A few simple fixes.
1)Fix up some possible divide by zero issues in various drivers.
2)Prevent a memory leak in an error path in lis3l02dq
3)Make sure the PTR_ERR call in at91_adc matches the
check for IS_ERR just above it rather than using a different
pointer.
Merges fine against v3.6rc4
Don't zero out bits 15..12 of the data value in `das08jr_ao_winsn()` as
that knobbles the upper three-quarters of the output range for the
'das08jr-16-ao' board.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The element of `das08_boards[]` for the 'das08jr-16-ao' board has the
`ai_encoding` member set to `das08_encode12`. It should be set to
`das08_encode16` same as the 'das08jr/16' board. After all, this board
has 16-bit AI resolution.
The description of the A/D LSB register at offset 0 seems incorrect in
the user manual "cio-das08jr-16-ao.pdf" as it implies that the AI
resolution is only 12 bits. The diagrams of the A/D LSB and MSB
registers show 15 data bits and a sign bit, which matches what the
software expects for the `das08_encode16` AI encoding method.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When attaching a PCI device manually via the comedi driver `attach` hook
(`das08_attach()`) (called by the comedi core for the `COMEDI_DEVCONFIG`
ioctl), its reference count is incremented in the `for_each_pci_dev`
loop (in `das08_find_pci()`). It is decremented when the `detach` hook
(`das08_detach()`) is called to detach the device. However, when the
PCI device is attached automatically via the `attach_pci` hook
(`das08_attach_pci()`, called at probe time via
`comedi_pci_auto_config()`) it's reference count is not incremented so
there will be an unmatched decrement when detaching the device.
Increment the PCI device reference count in `das08_attach_pci()` to
correct the mismatch.
Once support for manual configuration has been removed from this driver,
the calls to `pci_dev_get()` and `pci_dev_put()` can be removed.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When attaching a PCI device manually via the comedi driver `attach` hook
(`pci230_attach()`) (called by the comedi core for the `COMEDI_DEVCONFIG`
ioctl), its reference count is incremented in the `for_each_pci_dev`
loop (in `pci230_find_pci_dev()`). It is decremented when the `detach`
hook (`pci230_detach()`) is called to detach the device. However, when
the PCI device is attached automatically via the `attach_pci` hook
(`pci230_attach_pci()`, called at probe time via
`comedi_pci_auto_config()`) it's reference count is not incremented so
there will be an unmatched decrement when detaching the device.
Increment the PCI device reference count in `pci230_attach_pci()` to
correct the mismatch.
Once support for manual configuration has been removed from this driver,
the calls to `pci_dev_get()` and `pci_dev_put()` can be removed.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When attaching a PCI device manually via the comedi driver `attach` hook
(`pc263_attach()`) (called by the comedi core for the `COMEDI_DEVCONFIG`
ioctl), its reference count is incremented in the `for_each_pci_dev`
loop (in `pc263_find_pci_dev()`). It is decremented when the `detach`
hook (`pc263_detach()`) is called to detach the device. However, when
the PCI device is attached automatically via the `attach_pci` hook
(`pc263_attach_pci()`, called at probe time via
`comedi_pci_auto_config()`) it's reference count is not incremented so
there will be an unmatched decrement when detaching the device.
Increment the PCI device reference count in `pc263_attach_pci()` to
correct the mismatch.
Once support for manual configuration has been removed from this driver,
the calls to `pci_dev_get()` and `pci_dev_put()` can be removed.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
