Under some circumstances the driver remove function may be called before
the driver is fully initialized. So we can't assume that we know where
our towel is at, or that all of the data structures are initialized.
To ensure that we don't panic, check that the vsi_res pointer is valid
before dereferencing it. Then drink beer and eat peanuts.
Change-ID: If697b4db57348e39f9538793e16aa755e3e1af03
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for configuring RSS on behalf of the VFs. This removes the
burden of dealing with different hardware interfaces from the VF
drivers, allowing for better future compatibility.
Change-ID: Icea75d3f37241ee8e447be5779e5abb53ddf04c0
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Looking over the documentation it turns out enabling IPIP and SIT offloads
for i40e is pretty straightforward. As such I decided to enable them with
this patch. In my testing I am seeing an improvement of 8 to 10 Gb/s
for IPIP and SIT tunnels with this offload enabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The feature flags list for i40e and i40evf is beginning to become pretty
massive. I plan to add another 4 or so features to these drivers and
duplicating the flags for each and every flags list is becoming a bit
repetitive.
The primary change here is that we now build our features list around
hw_encap_features. After that we assign that to vlan_features,
hw_features, and finally map that onto features. In addition we end up
throwing features onto hw_encap_features that end up having no effect such
as the Rx offloads and SCTP_CRC. However that should have no impact and
makes things a bit easier for us as hw_encap_features is one of the less
updated features maps available.
For i40evf I went through and sanity checked a few features as well.
Specifically RXCSUM was being set as a read-only feature which didn't make
much sense. I have updated things so we can clear the NETIF_F_RXCSUM flag
since that is really a software feature and not a hardware one anyway so
disabling it is just a matter of ignoring the result from the hardware.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Yuval Mintz says:
====================
qed*: driver updates
[Was previous termed 'eeprom access et al.', but seemed a bit
inappropriate given we've dropped the eeprom patch for now.
Still waiting for some inputs on that one, BTW]
This patch series contains some ethtool-related enhancements.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The APIs for making this sort of configuration [e.g., via ethtool] are
already present in qede, but the current configuration flow in qed doesn't
respect it.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's some inconsistency in current logic determining whether the
link settings of a given interface can be changed; I.e., in all modes
other than the so-called `deault' mode the interfaces are forbidden from
changing the configuration - but even this rule is not applied to all
user APIs that may change the configuration.
Instead, let the core-module [qed] decide whether an interface can change
the configuration by supporting a new API function. We also revise the
current rule, allowing all interfaces to change their configurations while
laying the infrastructure for future modes where an interface would be
blocked from making such a configuration.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a getter for the interfaces private flags.
The only parameter currently supported is whether the interface is a
coupled function [required for supporting 100g].
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a difference in statsitics' names starting at qed and
propagating to qede, where egress counters indicate ranges while ingress
counters indiciate high-end.
Align all statistcs to follow the same conventions - name indicates range.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should call consume_skb(skb) when skb is properly consumed,
or kfree_skb(skb) when skb must be dropped in error case.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now have proper per-listener but also per network namespace counters
for SYN packets that might be dropped.
We replace the kfree_skb() by consume_skb() to be drop monitor [1]
friendly, and remove an obsolete comment.
FastOpen SYN packets can carry payload in them just fine.
[1] perf record -a -g -e skb:kfree_skb sleep 1; perf report
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2016-04-25
This series contains updates to ixgbe and ixgbevf.
Emil provides several patches, starting with the consolidation of the
logic behind configuring spoof checking. Fixed an issue which was
causing link issues for backplane devices because x550em_a/x devices
did not have a default value for mac->ops.setup_link. Refactored the
ethtool stats to bring the logic closer to how ixgbe handles stats and
sets up per-queue stats for ixgbevf.
Mark adds a new register to wait for previous register writes to complete
before issuing a register read, which is needed when slower links are
in use. Fixed the flow control setup for x550em_a, the incorrect
fc_setup function was being used.
Don added a workaround for empty SFP+ cage crosstalk, since on some
systems the crosstalk could lead to link flap on empty SFP+ cages.
Jake converts ixgbe and ixgbevf to use the BIT() macro.
Alex Duyck adds support for partial GSO segmentation in the case of
tunnels for ixgbe and ixgbevf. Then preps for HyperV by moving the API
negotiation into mac_ops.
Arnd Bergmann provides a fix for the ARM compile warnings in linux-next
by converting the use of a udelay() to msleep().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel says:
====================
netlink: align attributes when needed (patchset #2)
This is the continuation (series #2) of the work done to align netlink
attributes when these attributes contain some 64-bit fields.
In patch #3, I didn't modify the function ila_encap_nlsize(). I was waiting
feedback for this patch: http://patchwork.ozlabs.org/patch/613766/
If it's approved, there will be an update to switch nla_total_size() to
nla_total_size_64bit() after the merge of net in net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
d894ba18d4 ("soreuseport: fix ordering for mixed v4/v6 sockets")
was merged as a bug fix to the net tree. Two conflicting changes
were committed to net-next before the above fix was merged back to
net-next:
ca065d0cf8 ("udp: no longer use SLAB_DESTROY_BY_RCU")
3b24d854cb ("tcp/dccp: do not touch listener sk_refcnt under synflood")
These changes switched the datastructure used for TCP and UDP sockets
from hlist_nulls to hlist. This patch applies the necessary parts
of the net tree fix to net-next which were not automatic as part of the
merge.
Fixes: 1602f49b58 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net")
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Valdis reported tons of stack dumps caused by WARN_ON() in
sock_owned_by_user()
This test needs to be relaxed if/when lockdep disables itself.
Note that other lockdep_sock_is_held() callers are all from
rcu_dereference_protected() sections which already are disabled
if/when lockdep has been disabled.
Fixes: fafc4e1ea1 ("sock: tigthen lockdep checks for sock_owned_by_user")
Reported-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newly added x550em_a support causes a link failure on ARM because of
an overly long time passed into udelay():
ERROR: "__bad_udelay" [drivers/net/ethernet/intel/ixgbe/ixgbe.ko] undefined!
There are multiple variants of the ixgbe_acquire_swfw_sync_*() function,
and the other ones all use msleep(), so we can safely assume that all
callers are allowed to sleep, which makes msleep() a better replacement
than mdelay().
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 49425dfc74 ("ixgbe: Add support for x550em_a 10G MAC type")
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch moves API negotiation into mac_ops. The general idea here is
that with HyperV on the way we need to make certain that anything that will
have different versions between HyperV and a standard VF needs to be
abstracted enough so that we can have a separate function between the two
so we can avoid changes in one breaking something in the other.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for partial GSO segmentation in the case of
tunnels. Specifically with this change the driver an perform segmentation
as long as the frame either has IPv6 inner headers, or we are allowed to
mangle the IP IDs on the inner header. This is needed because we will not
be modifying any fields from the start of the start of the outer transport
header to the start of the inner transport header as we are treating them
like they are just a block of IP options.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Also cleanup a case where we're bit shifting a value into place, and use
an unsigned constant. Make use of the unsigned postfix in places where
BIT() macro is not appropriate.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make use of GENMASK instead of open coding the equivalent operation
incorrectly.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Several areas of ixgbe were written before widespread usage of the
BIT(n) macro. With the impending release of GCC 6 and its associated new
warnings, some usages such as (1 << 31) have been noted within the ixgbe
driver source. Fix these wholesale and prevent future issues by simply
using BIT macro instead of hand coded bit shifts.
Also fix a few shifts that are shifting values into place by using the
'u' prefix to indicate unsigned. It doesn't strictly matter in these
cases because we're not shifting by too large a value, but these are all
unsigned values and should be indicated as such.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It is possible on some systems that crosstalk could lead to link flap
on empty SFP+ cages. A new NVM bit was defined to let SW know it
needs to implement the work around which consists of verifying that
there is a module in the cage before acting on the LSC.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Somehow the wrong fc_setup function was used for x550em_a, so
correct that. Also set setup_link to NULL as its value is
determined later, just like it is with X550EM_x.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement per-queue statistics for packets, bytes and busy poll
specific counters.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This brings the logic closer to how we handle the stats in ixgbe and it
sets us up for introducing per-queue stats.
Use IXGBEVF_STAT and IXGBEVF_NETDEV_STAT for accessing the driver and
netdev stats respectively. This way we don't have to calculate the
stats based on register values which could lead to the counters not
being initialized properly when the interface is down.
IXGBEVF_QUEUE_STATS_LEN is set to include the number of queues.
Also some defines were renamed to use the IXGBEVF prefix.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use a new register to wait for previous register writes to complete
before issuing a register read. This is needed when slower links
are in use.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
RNDIS_STATUS_NETWORK_CHANGE event is handled as two "half events" --
media disconnect & connect. The second half should be added to the list
head, not to the tail. So all events are processed in normal order.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This field is used to record the RX queue index for a redirect action
passed via ring_cookie field in struct ethtool_rx_flow_spec which is
a u64 value.
For ex: after adding a filter rule to redirect to a VF using ethtool
# echo 4 > /sys/class/net/p4p1/device/sriov_numvfs
# ethtool -N p4p1 flow-type ip4 src-ip 192.168.0.1 action 0x100000000
querying for the rule shows the Action as 'Direct to queue 0'
# ethtool -n p4p1
4 RX rings available
Total 1 rules
Filter: 2045
Rule Type: Raw IPv4
Src IP addr: 192.168.0.1 mask: 0.0.0.0
Dest IP addr: 0.0.0.0 mask: 255.255.255.255
TOS: 0x0 mask: 0xff
Protocol: 0 mask: 0xff
L4 bytes: 0x0 mask: 0xffffffff
VLAN EtherType: 0x0 mask: 0xffff
VLAN: 0x0 mask: 0xffff
User-defined: 0x0 mask: 0xffffffffffffffff
Action: Direct to queue 0
With this fix, ethtool will report the right queue index even for VFs.
Action: Direct to queue 4294967296
Here 4294967296 corresponds to 0x100000000.
We need to update 'ethtool' to report the queue index as a Hex value so
that it is more user friendly and matches with the 'action' value that
is passed when adding the rule.
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X550EM_a/x did not have a default value for mac->ops.setup_link which
was causing link issues for backplane devices.
This patch sets mac->ops.setup_link to ixgbe_setup_mac_link_X540 for
X550EM_a/x which is also default for X550. This will result in
mac->ops.setup_link calling the link setup function for the respective
PHY type in case we do not need a special function to deal with it.
Reported-by: Ken Cox <jkc@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously the PF driver would only set VLAN spoof checking if
the VF had created VLANs. This was done by setting and checking
a counter (vlan_count) whenever a VLAN was created by the VF.
However it is possible for the vlan_count to be !=0 while there are
no VLANs assigned to the VF due to the count incrementing every
time a VLAN 0 is added on ifdown/up, which resulted in VLAN spoofing
always being set for those VFs.
This patch cleans up the logic by unconditionally setting VLAN based on
how the VF is configured (via ip link set ethX vf Y spoofchk on/off).
This change also resolves an issue where the VLAN spoofing can remain
set even after being disabled by the user due to the driver enabling
VLAN spoof checking every time a VLAN is added to the VF, but would
only allow changes in the setting if vlan_count != 0.
Also default_vf_vlan_id and vlans_enabled were removed from the
vf_data_storage structure since they are not being used in the driver.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Consolidate the logic behind configuring spoof checking:
Move the setting of the MAC, VLAN and Ethertype spoof checking into
ixgbe_ndo_set_vf_spoofchk().
Change ixgbe_set_mac_anti_spoofing() to set MAC spoofing per VF similar
to the VLAN and Ethertype functions - this allows us to call the helper
functions in ixgbe_ndo_set_vf_spoofchk() for all spoof check types and
only disable MAC spoof checking when creating MACVLAN.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Linux TCP stack painfully segments all TSO/GSO packets before retransmits.
This was fine back in the days when TSO/GSO were emerging, with their
bugs, but we believe the dark age is over.
Keeping big packets in write queues, but also in stack traversal
has a lot of benefits.
- Less memory overhead, because write queues have less skbs
- Less cpu overhead at ACK processing.
- Better SACK processing, as lot of studies mentioned how
awful linux was at this ;)
- Less cpu overhead to send the rtx packets
(IP stack traversal, netfilter traversal, drivers...)
- Better latencies in presence of losses.
- Smaller spikes in fq like packet schedulers, as retransmits
are not constrained by TCP Small Queues.
1 % packet losses are common today, and at 100Gbit speeds, this
translates to ~80,000 losses per second.
Losses are often correlated, and we see many retransmit events
leading to 1-MSS train of packets, at the time hosts are already
under stress.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 42b18f605f ("tipc: refactor function tipc_link_timeout()"),
introduced a bug which prevents sending of probe messages during
link synchronization phase. This leads to hanging links, if the
bearer is disabled/enabled after links are up.
In this commit, we send the probe messages correctly.
Fixes: 42b18f605f ("tipc: refactor function tipc_link_timeout()")
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau says:
====================
tcp: Handle txstamp_ack when fragmenting/coalescing skbs
This patchset is to handle the txstamp-ack bit when
fragmenting/coalescing skbs.
The second patch depends on the recently posted series
for the net branch:
"tcp: Merge timestamp info when coalescing skbs"
A BPF prog is used to kprobe to sock_queue_err_skb()
and print out the value of serr->ee.ee_data. The BPF
prog (run-able from bcc) is attached here:
BPF prog used for testing:
~~~~~
from __future__ import print_function
from bcc import BPF
bpf_text = """
int trace_err_skb(struct pt_regs *ctx)
{
struct sk_buff *skb = (struct sk_buff *)ctx->si;
struct sock *sk = (struct sock *)ctx->di;
struct sock_exterr_skb *serr;
u32 ee_data = 0;
if (!sk || !skb)
return 0;
serr = SKB_EXT_ERR(skb);
bpf_probe_read(&ee_data, sizeof(ee_data), &serr->ee.ee_data);
bpf_trace_printk("ee_data:%u\\n", ee_data);
return 0;
};
"""
b = BPF(text=bpf_text)
b.attach_kprobe(event="sock_queue_err_skb", fn_name="trace_err_skb")
print("Attached to kprobe")
b.trace_print()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree, mostly from Florian Westphal to sort out the lack of sufficient
validation in x_tables and connlabel preparation patches to add
nf_tables support. They are:
1) Ensure we don't go over the ruleset blob boundaries in
mark_source_chains().
2) Validate that target jumps land on an existing xt_entry. This extra
sanitization comes with a performance penalty when loading the ruleset.
3) Introduce xt_check_entry_offsets() and use it from {arp,ip,ip6}tables.
4) Get rid of the smallish check_entry() functions in {arp,ip,ip6}tables.
5) Make sure the minimal possible target size in x_tables.
6) Similar to #3, add xt_compat_check_entry_offsets() for compat code.
7) Check that standard target size is valid.
8) More sanitization to ensure that the target_offset field is correct.
9) Add xt_check_entry_match() to validate that matches are well-formed.
10-12) Three patch to reduce the number of parameters in
translate_compat_table() for {arp,ip,ip6}tables by using a container
structure.
13) No need to return value from xt_compat_match_from_user(), so make
it void.
14) Consolidate translate_table() so it can be used by compat code too.
15) Remove obsolete check for compat code, so we keep consistent with
what was already removed in the native layout code (back in 2007).
16) Get rid of target jump validation from mark_source_chains(),
obsoleted by #2.
17) Introduce xt_copy_counters_from_user() to consolidate counter
copying, and use it from {arp,ip,ip6}tables.
18,22) Get rid of unnecessary explicit inlining in ctnetlink for dump
functions.
19) Move nf_connlabel_match() to xt_connlabel.
20) Skip event notification if connlabel did not change.
21) Update of nf_connlabels_get() to make the upcoming nft connlabel
support easier.
23) Remove spinlock to read protocol state field in conntrack.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel says:
====================
netlink: align attributes when needed (patchset #1)
This is the continuation of the work done to align netlink attributes
when these attributes contain some 64-bit fields.
David, if the third patch is too big (or maybe the series), I can split it.
Just tell me what you prefer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Goal of this patch is to use the new libnl API to align netlink attribute
when needed.
The layout of the netlink message will be a bit different after the patch,
because the padattr (TASKSTATS_TYPE_STATS) will be inside the nested
attribute instead of before it.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this function, nla_data() is aligned on a 64-bit area.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
