Enable Block Data Update in hts221_probe() in order to avoid to reconfigure
it every time the sensor is enabled
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move bit-shift in hts221_write_with_mask() instead of coding
the shift depth in the configured value. That change will be necessary
to fix an issue in device power-down procedure.
Simplify hts221_avg_list table management
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for CCS811 VOC sensor. This patch adds support
for reading current and voltage across the sensor and TVOC
and equivalent CO2 values.
Scale and offset values have been computed according to datasheet:
- For current: raw value is in microamps
=> 0.001 scale to convert to milliamps
- For voltage: 1.65V = 1023, therefore 1650mV = 1023
=> 1650.0/1023 = 1.612903 scale to convert to millivolts
- For eCO2: raw value range is from 400ppm to 8192ppm.
=> (val - 400) * (100 - 0) / (8192 - 400) + 0 =
(val - 400) * 0.01283367 => offset: -400, scale = 0.012834
to get a percentage value
-For TVOC: raw value range is from 0ppb to 1187ppb.
=> (val - 0) * 100 / (1187 - 0) + 0 = val * 0.0842459 =>
scale = 0.084246 for getting a percentage value
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Alison Schofield <amsfield22@gmail.com>
Signed-off-by: Narcisa Ana Maria Vasile <narcisaanamaria12@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The gpiod API checks for NULL descriptors, so there is no need to
duplicate the check in the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Drop static on a local variable, when the variable is initialized before
any possible use. Thus, the static has no benefit.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
After probe we would put the device in normal mode, after a runtime
suspend-resume we would put it back in normal mode. But for a regular
suspend-resume we would only put it back in normal mode if triggers
or events have been requested. This is not consistent and breaks
reading raw values after a suspend-resume.
This commit changes the regular resume path to also unconditionally put
the device back in normal mode, fixing reading of raw values not working
after a regular suspend-resume cycle.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When adding maps to the list, they were added using list_add, which adds
them in LIFO order. When parsing using iio_channel_get_all(), these
elements are hence returned in reverse order. As a result, the iio_hwmon
mapping maps the first entry to the last channel and so on.
Signed-off-by: Gaurav Gupta <gauragup@cisco.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This adds support for STM32F4 Digital-To-Analog converter.
Add compatible configuration data to handle hfsel (not present
in stm32f4).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix error message, there's no 'st,dac-channel' property, but 'reg'
(see https://lkml.org/lkml/2017/4/3/567).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Don't populate array startup_lookup on the stack but instead make
it static. Makes the object code smaller.
Before:
text data bss dec hex filename
21754 5440 128 27322 6aba drivers/iio/adc/at91_adc.o
After:
text data bss dec hex filename
21613 5496 128 27237 6a65 drivers/iio/adc/at91_adc.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
I noticed in its DSDT that one of my tablets actually is using the GPADC
pin for temperature monitoring.
The whole axp288_adc_set_ts() function is a bit weird, in the past it was
removed because it seems to make no sense, then this was reverted because
of regressions.
So I decided to test the special GPADC pin handling on this tablet.
Conclusion: not only is axp288_adc_set_ts() necessary, we need to sleep a
bit after making the AXP288_ADC_TS_PIN_CTRL changes before sampling the
GPADC, otherwise it will often (about 80% of the time) read 0 instead of
its actual value.
It seems that there is only 1 bias current source and to be able to use it
for the GPIO0 pin in GPADC mode it must be temporarily turned off for the
TS pin, but the datasheet does not mention this.
This commit adds a sleep after disabling the TS pin bias current,
fixing the GPADC more often then not wrongly returning 0.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In order to use the standard name convention rename H3LIS331DL_DRIVER_NAME
macro in H3LIS331DL_ACCEL_DEV_NAME
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add H3LIS331DL, LIS331DL and LIS3LV02DL entries in st_accel_id_table
Fixes: 1e52fefc9b (iio: accel: Add support for the h3lis331dl accel)
Fixes: bbf5f037fa (iio: st_accel: support the LIS331DL sensor)
Fixes: 3acddf74f8 (iio: st-sensors: add support for lis3lv02d accel)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Making the const array startup_lookup static rather having it on the
stack saves 69 bytes. Add in missing int specifier to clean up a
checkpatch warning.
Before:
text data bss dec hex filename
10297 2800 128 13225 33a9 drivers/iio/adc/at91-sama5d2_adc.o
After:
text data bss dec hex filename
10140 2888 128 13156 3364 drivers/iio/adc/at91-sama5d2_adc.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Making the const array init_data static rather having it on the
stack saves us a couple hundreds of bytes:
Before:
text data bss dec hex filename
3175 848 0 4023 fb7 drivers/iio/accel/da311.o
After:
text data bss dec hex filename
2860 936 0 3796 ed4 drivers/iio/accel/da311.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check return value from call to of_match_device()
in order to prevent a NULL pointer dereference.
In case of NULL print error message and return -ENODEV
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check return value from call to of_match_device()
in order to prevent a NULL pointer dereference.
In case of NULL print error message and return -ENODEV
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds support for Diolan DLN2 ADC via IIO's ADC interface.
ADC is the fourth and final component of the DLN2 for the kernel.
Signed-off-by: Jack Andersen <jackoalan@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In order to select the alternate voltage reference pair (VALTH/VALTL), the
right value for the REFSEL field in the ADCx_CFG register is "01", leading
to 0x800 as register mask. See section 8.2.6.4 in the reference manual[1].
[1] http://www.nxp.com/docs/en/reference-manual/VFXXXRM.pdf
Fixes: a775427632 ("iio:adc:imx: add Freescale Vybrid vf610 adc driver")
Signed-off-by: Stefan-Gabriel Mirea <stefan-gabriel.mirea@nxp.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add SPI Serial Interface Mode (SIM) register information
in st_sensor_settings look up table to support devices
(like LSM303AGR accel sensor) that allow just SPI-3wire
communication mode. SIM mode has to be configured before any
other operation since it is not enabled by default and the driver
is not able to read without that configuration
Whilst a fairly substantial patch, the actual logic is simple and it
is better to have the generic fix than a band aid.
Fixes: ddc05fa286 (iio: st-accel: add support for lsm303agr accel)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add newlines to the macro definitions and use a more common style.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The LTC2741 and LTC2473 are single voltage ADC chips. The LTC2473
is similar to the LTC2471 but outputs a signed differential value.
Datasheet:
http://cds.linear.com/docs/en/datasheet/24713fb.pdf
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Set up and use triggered buffer if there is irq defined for device in
device tree. Trigger producer triggers from rpr0521 drdy interrupt line.
Trigger consumer reads rpr0521 data to scan buffer.
Depends on previous commits of _scale and _offset.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Inheriting the ADC BIAS current settings from the BIOS instead of
hardcoding then causes the AXP288 to disable charging (I think it
mis-detects an overheated battery) on at least one model tablet.
So lets go back to hard coding the values, this reverts
commit fa2849e964 ("iio: adc: axp288: Drop bogus
AXP288_ADC_TS_PIN_CTRL register modifications"), fixing charging not
working on the model tablet in question.
The exact cause is not fully understood, hence the revert to a known working
state.
Cc: stable@vger.kernel.org
Reported-by: Umberto Ixxo <sfumato1977@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When initializing interrupts, the devm_request_any_context_irq will
enable them right away. An atomic flag was set in sun4i_irq_init and read
in the interrupt handler to make sure no unwanted interrupts were
handled. If an unwanted interrupt occurred, the handler would disable
the irq and return IRQ_HANDLED. However, at the end of sun4i_irq_init,
the irq would be disabled as well, resulting in an unbalanced enable
(since there are more disables than enables, the code enabling the
interrupt would never be called).
When reading the ADC or the temperature, the respective irq would be
enabled in the read function and disabled in the irq handler. In the
read function, we would wait for a completion (with a timeout) that will
be set in the irq handler. However, if the completion is never set or if
the wait for completion times out, the irq would not be disabled in the
read function resulting in an unbalanced enable once the read function
is called again (since there are 2+ enables for no disable).
Moving disable_irq from the irq handler to the read function get rid of
these two cases of unbalanced enable.
Fixes: d1caa99055 ("iio: adc: add support for Allwinner SoCs ADC")
Reported-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
- Add PMBus client driver for IR35221
- Add support for NCT6795D to nct6775 driver
- Functional improvements to adt7475, aspeed-pwm-tacho, and ibmpowernv drivers
- Minor fixes and cleanups in various drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJZWYZwAAoJEMsfJm/On5mBCSYP/3GmiLKCS1aTupt31QUlHBw0
yJfoL8RgwbQFR83y2fI679G1dgM1a0fyIBmFCNER5jPuxhbg5ZMb+BqT5SUDYXD8
+isABxmOkWfszze5p6UlQHl5wBg+D+rV9IluxLniT74nKRtlKcIU3ePjii6vpAfK
5rPxqTzwzVNHfDygiCK8DwflS5s8njOUJy1zLXroe4kUvu+NJnZb0nDdkD26zN75
JHYNiqso2UQd2kD3kJgNzJ4t9OGcNWwPse4Y/z0P6YAMEbs8zNuS0MbVURsk17/9
12w8eNOzsmj9m3MGKg9d6c75tG75ZRdsZzUxLEngO1LafKZ7o1YV9DBjIyhVTRxi
nKofp0m/7xw/5R6XhyezL5EYohDFxjTNCT+h+GQoqvG4mZl4piG6ew4t6iG0AmJy
91rXmUdYagXKU+DxNbBNM4MMwXkNHG6+jhufF9g1MTr9K7kLu9URU2gWA7Tm5/1u
/0/Qt+XBr112T+luj8BHVYTiC7iaEhtBWFIFPNeay2+2Jt2nyYLcngiIuJLmwuCe
vyK9i9j5P7jhxS23omzn5Ca8hdUmtOABR5cKOwpPur0yfGLjLAQG+vBW5mYu6yJt
El8QftmRN/PWnEglG+nIJG35RL3XzCl6/CyI//C6tVHJViItUPQl/ZXpZUFXHsFY
TeXRyHZGGcCQtBbsFUoZ
=J5ye
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- Add PMBus client driver for IR35221
- Add support for NCT6795D to nct6775 driver
- Functional improvements to adt7475, aspeed-pwm-tacho, and ibmpowernv
drivers
- Minor fixes and cleanups in various drivers
* tag 'hwmon-for-linus-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (22 commits)
hwmon: (aspeed-pwm-tacho) Poll with short sleeps.
hwmon: (aspeed-pwm-tacho) reduce fan_tach period
hwmon: (ibmpowernv) Add current(A) sensor
hwmon: (ibmpowernv) introduce a legacy_compatibles array
hwmon: (pwm-fan) Switch to new atomic PWM API
hwmon: (scpi) Fix the scale of SCP sensor readings
hwmon: (aspeed-pwm-tacho) Enable both edge measurement.
hwmon: (ibmpowernv) Add highest/lowest attributes to sensors
hwmon: (pmbus) move header file out of I2C realm
hwmon: (max6639) move header file out of I2C realm
hwmon: (ltc4245) move header file out of I2C realm
hwmon: (ds620) move header file out of I2C realm
hwmon: (ads1015) move header file out of I2C realm
hwmon: (adt7475) temperature smoothing
hwmon: (adt7475) add high frequency support
hwmon: (adt7475) fan stall prevention
hwmon: (adt7475) replace find_nearest() with find_closest()
hwmon: (pmbus) Add client driver for IR35221
hwmon: (nct6775) Add support for NCT6795D
hwmon: (nct6775) Improve fan detection
...
Here is the "big" char/misc driver patchset for 4.13-rc1.
Lots of stuff in here, a large thunderbolt update, w1 driver header
reorg, the new mux driver subsystem, google firmware driver updates, and
a raft of other smaller things. Full details in the shortlog.
All of these have been in linux-next for a while with the only reported
issue being a merge problem with this tree and the jc-docs tree in the
w1 documentation area. The fix should be obvious for what to do when it
happens, if not, we can send a follow-up patch for it afterward.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpXKA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynLrQCdG9SxRjAbOd6pT9Fr2NAzpUG84YsAoLw+I3iO
EMi60UXWqAFJbtVMS9Aj
=yrSq
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the "big" char/misc driver patchset for 4.13-rc1.
Lots of stuff in here, a large thunderbolt update, w1 driver header
reorg, the new mux driver subsystem, google firmware driver updates,
and a raft of other smaller things. Full details in the shortlog.
All of these have been in linux-next for a while with the only
reported issue being a merge problem with this tree and the jc-docs
tree in the w1 documentation area"
* tag 'char-misc-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (147 commits)
misc: apds990x: Use sysfs_match_string() helper
mei: drop unreachable code in mei_start
mei: validate the message header only in first fragment.
DocBook: w1: Update W1 file locations and names in DocBook
mux: adg792a: always require I2C support
nvmem: rockchip-efuse: add support for rk322x-efuse
nvmem: core: add locking to nvmem_find_cell
nvmem: core: Call put_device() in nvmem_unregister()
nvmem: core: fix leaks on registration errors
nvmem: correct Broadcom OTP controller driver writes
w1: Add subsystem kernel public interface
drivers/fsi: Add module license to core driver
drivers/fsi: Use asynchronous slave mode
drivers/fsi: Add hub master support
drivers/fsi: Add SCOM FSI client device driver
drivers/fsi/gpio: Add tracepoints for GPIO master
drivers/fsi: Add GPIO based FSI master
drivers/fsi: Document FSI master sysfs files in ABI
drivers/fsi: Add error handling for slave
drivers/fsi: Add tracepoints for low-level operations
...
This patch fixes the following checkpatch warnings:
Prefer 'unsigned int' to bare use of 'unsigned
Signed-off-by: Reno Farnesi <nfarnesi4@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add device tree support for LPS22HB, LPS25H, LPS331AP, LPS001WP
pressure sensors
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add device tree support for LIS3MDL and LSM303AGR magnetometer sensors
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Don't inflate the kernel size with data that isn't used. The conditional
declaration also fixes the following warning when building with clang:
drivers/iio/magnetometer/ak8975.c:704:36: error: variable 'ak_acpi_match'
is not needed and will not be emitted
[-Werror,-Wunneeded-internal-declaration]
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add missing hooks in the LTC2497 IIO driver to allow hwmon mapping.
Signed-off-by: Gaurav Gupta <gauragup@cisco.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The array stm32h7_adc_ckmodes_spec does not need to be in global scope, so
make it static.
Cleans up sparse warning:
"symbol 'stm32h7_adc_ckmodes_spec' was not declared. Should it be static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some part of the configuration are not touched after the probe
and if something goes wrong on writing the initial one,
the chip will misbehave.
Adding an error checking ensures that the inital configuration will
be written correctly. Moreover ensures that a sensible configuration
will be saved in driver data and used subsequently as intended.
Signed-off-by: Angelo Compagnucci <angelo.compagnucci@gmail.com>
Reported-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Initial channel should be the first available channel on
all configurations, so changing to channel 0 available on
all supported chips.
Signed-off-by: Angelo Compagnucci <angelo.compagnucci@gmail.com>
Reported-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Open drain should work fine with rising or high level IRQs,
this code was due to some misunderstanding on my part.
Reported-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add a link to the TCS3472 datasheet in the AMS's website.
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch supports auxadc suspend/resume flow.
Disable auxadc clk and power in suspend function.
Enable axuadc clk and power in resume function.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add open drain support in order to share requested IRQ line between
st_lsm6dsx device and other peripherals
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add of_match_table for Measurement-Specialties htu21 temperature & humidity sensor and humidity part of MS8607 sensor
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added support for suspend/resume functionality for the ADC IP
in sama5d2 SoC.
In order to enter Suspend to ram mode (backup + self refresh mode for
memory), in which the ADC IP is no longer powered, we need to reset the
pins to default state, for the scenario when they are also used for I2C
bus to communicate with the PMIC.
On resume, we need to reconfigure the ADC IP registers and reconfigure the
trigger registers in the case when the suspend procedure is done while
sysfs has the buffer and trigger enabled.
In the case the suspend happens exactly during a software triggered
conversion, the request will time out, because we reset and power down
the ADC.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In order to add proper device tree support give a more general name
to of_device_id table
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Move st_sensors_of_i2c_probe() in st_sensors_core and rename it in
st_sensors_of_name_probe(). That change is necessary to add device-tree
support in spi code otherwise the rest of the autodetection will fail
since spi->modalias (and indio_dev->name) will be set using compatible
string value that differs from standard sensor name
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Enable multiread by default for LIS3MDL since using I2C interface
the subaddr Msb is used to automatically increase the slave address
during multiple data read/write. In the same way, using SPI interface,
bit 1 in register address is used to enable auto-increment of the slave
address in multiple read/write.
Fixes: 872e79add7 (iio:magn: Add STMicroelectronics magn driver)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The integration time is controlled by the ATIME register only. However,
this register is written by i2c_smbus_write_word_data() in write_raw().
We actually don't need to write a subsequent register. So just use
i2c_smbus_write_byte_data() instead.
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
While the INA226 has a conversion ready flag (CVRF) in the R/W Mask/Enable
register with read-to-clear semantics, the corresponding bit of the INA219
(CNVR) is part of the bus voltage register. The flag is cleared by reading
the power register.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added support for the external hardware trigger on pin ADTRG,
integrated the three possible edges into the driver
and created buffer management for data retrieval
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
To keep IMX7D_ADC text consistent with other iio/adc entries, add
the vendor name to the driver menu text.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add of_match_table and point it to a list of compatible device tree
device id's.
Signed-off-by: Michael Stecklein <m-stecklein@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Include datasheet links, add i2c_device_id entries, and update
kconfig help for compatible HDC10xx devices: HDC1000, HDC1008,
HDC1010, HDC1050, and HDC1080.
Signed-off-by: Michael Stecklein <m-stecklein@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add proper support for L3GD20H gyroscope sensor. In particular:
- use L3GD20H as device name instead of L3GD20
- fix available full scales
- fix available sample frequencies
Note that the original patch listed first below introduced broken support for
this part. The second patch drops the support as it didn't work.
This new patch brings in working support.
Fixes: 9444a300c2 (IIO: Add support for L3GD20H gyroscope)
Fixes: a065771641 ("iio:gyro: bug on L3GD20H gyroscope support")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for the BOSC0200 ACPI device id used on some x86 tablets.
note driver_data is not set to a specific model, driver_data is not
used anyways (instead detection is done on the chip_id reg) and the
2 tablets with a BOSC0200 ACPI device id I've have 2 different chips,
one has a BMA250E, the other a BMA222E.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
A few reverts here. One was a general failure to notice a device was already
supported by another driver. The second is due to a review comment pointing
out that the original patch was a bad idea and would break existing systems.
Reverts
* bma180
- Revert addition of support for the BMA250E it is already supported by
the bmc150-accel and better supported at that. Oops.
* hi8435
- The fix for cleanup of the reset gpio stuff isn't a good way to go. It
breaks systems where an inverting level convertor is used. The right fix
is to make the original devicetree correct - even if it involves patching
the devicetree in kernel.
New Device Support
* stm32-adc
- STM32H7 support and bindings.
Features
* core
- add a hardware triggered operating mode for systems in which the actual
trigger is never seen by the kernel. This is typically only used when
a device 'can' use other triggers, but if a particular magic one is
enabled the interrupt is effectively handled in hardware and we never see
it.
* st-lsm6dsx
- support active low interrupts.
* stm32-adc
- Make the core adc clock optional as not all hardware supported requires it.
- Make the bus clock optional in the per instance driver as it may be shared
by all instances of the ADC and is handled by the core.
- Rework to have a data structure representing the device type specific
elements.
* stm32-trigger (and counter)
- Use the INDIO_HARDWARE_TRIGGERED_MODE where appropriate.
- Add an attribute to configure device modes for quadrature counting etc.
Clean ups and minor fixes
* IIO core.
- use __sysfs_match_string() helper rather than open coding the same.
* ad7791
- use sysfs_match_string() helper rather than open coding the same.
* aspeed-adc
- handle return value of clk_prepare_enable
* cpcap
- Fix default register values and ensure the battery thermistor is enabled
correctly.
- Fix the reported die temperature where we can - docs are lacking.
- Remove the hung interrupt quirk as no longer happens due to fix in the
mfd driver.
* hi8435
- Remove &s from hi8435_info definition as unneeded and inconsistent.
* hid-sensor-trgger
- Add kconfig depends on IIO_BUFFER (fixes patch in previous series)
* ina2xx
- Make the use of iio_info_mask* elements consistent for all channels.
This doesn't have any visible effect, but acts as clear documentation of
which channels various resulting attributes apply to.
* lpc32xx
- handle the return value of clk_prepare_enable.
* meson-saradc
- NULL instead of 0 for pointer.
* mma9551
- use NULL for GPIO connection ID to aid implementation fo ACPI support.
Here the connection ID doesn't actually tell us anything and it is much
easier to deal with the driver if it's not there.
* mpu6050
- Fix lock issues through use of a local mux.
- Replace sprintf with scnprintf as appropriate.
- Check whoami against all known values. This allows for a small number of
boards where we are really fishing for the part not being present at all.
It is unfortunately common to have undescribed changes to use newer chips.
We paper over this but just emitting a warning for those cases as long as
we know about.
* mxs-lradc
- Fix some non static warnings.
* rcar-adc
- Part of making the naming for this part consistent across the kernel.
* st_accel
- drop some spi_device_id entries for variants with no SPI support
* st_magn
- drop some spi_device_id entries for variants with no SPI support.
* sx9500
- Use devm_gpiod_get instead of indexed value with an index of 0 on all
occasions.
* twl4030
- Drop unused twl4030_get_madc_conversion as callers removed now throughout
kernel.
- Unexport twl4030_madc_conversion() as no used only within this driver.
- Drop twl4030_madc_user_params as not used now.
- Drop twl4030_madc_request.func_cb as not used now.
- Fold the twl4030-madc.h header into the driver as no longer used anywhere
else in the kernel.
* xilinx
- Handle the return value of clk_prepare_enable
-----BEGIN PGP SIGNATURE-----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=2fJI
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.13b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO new device support, features and cleanups for the 4.13 cycle.
A few reverts here. One was a general failure to notice a device was already
supported by another driver. The second is due to a review comment pointing
out that the original patch was a bad idea and would break existing systems.
Reverts
* bma180
- Revert addition of support for the BMA250E it is already supported by
the bmc150-accel and better supported at that. Oops.
* hi8435
- The fix for cleanup of the reset gpio stuff isn't a good way to go. It
breaks systems where an inverting level convertor is used. The right fix
is to make the original devicetree correct - even if it involves patching
the devicetree in kernel.
New Device Support
* stm32-adc
- STM32H7 support and bindings.
Features
* core
- add a hardware triggered operating mode for systems in which the actual
trigger is never seen by the kernel. This is typically only used when
a device 'can' use other triggers, but if a particular magic one is
enabled the interrupt is effectively handled in hardware and we never see
it.
* st-lsm6dsx
- support active low interrupts.
* stm32-adc
- Make the core adc clock optional as not all hardware supported requires it.
- Make the bus clock optional in the per instance driver as it may be shared
by all instances of the ADC and is handled by the core.
- Rework to have a data structure representing the device type specific
elements.
* stm32-trigger (and counter)
- Use the INDIO_HARDWARE_TRIGGERED_MODE where appropriate.
- Add an attribute to configure device modes for quadrature counting etc.
Clean ups and minor fixes
* IIO core.
- use __sysfs_match_string() helper rather than open coding the same.
* ad7791
- use sysfs_match_string() helper rather than open coding the same.
* aspeed-adc
- handle return value of clk_prepare_enable
* cpcap
- Fix default register values and ensure the battery thermistor is enabled
correctly.
- Fix the reported die temperature where we can - docs are lacking.
- Remove the hung interrupt quirk as no longer happens due to fix in the
mfd driver.
* hi8435
- Remove &s from hi8435_info definition as unneeded and inconsistent.
* hid-sensor-trgger
- Add kconfig depends on IIO_BUFFER (fixes patch in previous series)
* ina2xx
- Make the use of iio_info_mask* elements consistent for all channels.
This doesn't have any visible effect, but acts as clear documentation of
which channels various resulting attributes apply to.
* lpc32xx
- handle the return value of clk_prepare_enable.
* meson-saradc
- NULL instead of 0 for pointer.
* mma9551
- use NULL for GPIO connection ID to aid implementation fo ACPI support.
Here the connection ID doesn't actually tell us anything and it is much
easier to deal with the driver if it's not there.
* mpu6050
- Fix lock issues through use of a local mux.
- Replace sprintf with scnprintf as appropriate.
- Check whoami against all known values. This allows for a small number of
boards where we are really fishing for the part not being present at all.
It is unfortunately common to have undescribed changes to use newer chips.
We paper over this but just emitting a warning for those cases as long as
we know about.
* mxs-lradc
- Fix some non static warnings.
* rcar-adc
- Part of making the naming for this part consistent across the kernel.
* st_accel
- drop some spi_device_id entries for variants with no SPI support
* st_magn
- drop some spi_device_id entries for variants with no SPI support.
* sx9500
- Use devm_gpiod_get instead of indexed value with an index of 0 on all
occasions.
* twl4030
- Drop unused twl4030_get_madc_conversion as callers removed now throughout
kernel.
- Unexport twl4030_madc_conversion() as no used only within this driver.
- Drop twl4030_madc_user_params as not used now.
- Drop twl4030_madc_request.func_cb as not used now.
- Fold the twl4030-madc.h header into the driver as no longer used anywhere
else in the kernel.
* xilinx
- Handle the return value of clk_prepare_enable
Set multiread variable to false for LPS22HB pressure sensor since
it is already enabled in CTRL_REG2. Previous configuration does not
cause any issue in I2C communication since SUB Msb has no meaning
whereas it breaks register address in SPI communication
Fixes: e039e2f5b4 (iio:st_pressure:initial lps22hb sensor support)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The TSL2563 driver provides three iio channels, two of which are raw ADC
channels (channel 0 and channel 1) in the device and the remaining one
is calculated by the two. The ADC channel 0 only supports programmable
interrupt with threshold settings and this driver supports the event but
the generated event code does not contain the corresponding iio channel
type.
This is going to change userspace ABI. Hopefully fixing this to be
what it should always have been won't break any userspace code.
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
SPI bus is never generating error during transfer, so to check if
a chip is correctly connected on a SPI bus we enforce whoami check
to be correct. In this way we can assure SPI probe is failing if
there is no chip connected.
Note that this is really papering over boards that claim the device
is there when it isn't. Not a bad thing to cope with, but not
necessarily stable material.
Fixes: cec0154556 ("iio: inv_mpu6050: Check WHO_AM_I register on probe")
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Building a kernel with my configuration failed with:
> drivers/built-in.o: In function `hid_sensor_setup_batch_mode': staging/drivers/iio/common/hid-sensors/hid-sensor-trigger.c:104: undefined reference to `iio_buffer_set_attrs'
which is fixed by this patch.
Signed-off-by: Alexander Wuerstlein <arw@arw.name>
Fixes: 138bc7969c ("iio: hid-sensor-hub: Implement batch mode")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add buffer_impl.h as buffer.h was split into interface for using and
for internals. Without this industrialio-buffer-dmaengine.c fails
to compile.
Fixes:
commit 33dd94cb97 ("iio:buffer.h - split
into buffer.h and buffer_impl.h")
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add buffer_impl.h as buffer.h was split into interface for using and
for internals. Without this industrialio-buffer-dma.c fails
to compile.
Fixes:
commit 33dd94cb97 ("iio:buffer.h - split
into buffer.h and buffer_impl.h")
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
While using GPIO library API we might get into troubles in the future,
because we can't rely on label name in the driver since vendor firmware
might provide any GPIO pin there, e.g. "reset", and even mark it in _DSD
(in which case the request will fail).
To avoid inconsistency and potential issues we have two options:
a) generate GPIO ACPI mapping table and supply it via
acpi_dev_add_driver_gpios(), or
b) just pass NULL as connection ID.
The b) approach is much simpler and would work since the driver relies
on GPIO indices only. Moreover, the _CRS fallback mechanism, when
requesting GPIO, is going to be stricter, and supplying non-NULL
connection ID when neither _DSD, nor GPIO ACPI mapping is present, will
make request fail.
See
https://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio.git/commit/?h=for-next&id=ed7fcf1ed5ea4ea01243995ae085757a77cf0f3e for more background.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add validate function to be use to use the correct trigger.
Add an attribute to configure device mode like for quadrature and
enable modes
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Devices, like stm32 timer, could be triggered by hardware events which
are not buffer or software events. However it could be necessary to
validate the triggers like it is done for buffer or event triggered modes.
This patch add a new INDIO_HARDWARE_TRIGGERED operating mode for this
kind of devices and allow this mode to register trigger consumer.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Rick Altherr <raltherr@google.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This reverts commit f1320b0951.
The BMA250E is already handled by the bmc150-accel-i2c driver, which
supports the "E" variants of the BMA??? accelerometers better then the
bma180 driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This reverts commit 5333e88661.
The BMA250E is already handled by the bmc150-accel-i2c driver, which
supports the "E" variants of the BMA??? accelerometers better then the
bma180 driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Remove LSM303DLHC, LSM303DLM from st_magn_id_table since LSM303DL series
does not support spi interface
Fixes: 872e79add7 (iio: magn: Add STMicroelectronics magn driver)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Remove LSM303DL, LSM303DLM, LSM303DLH, LSM303DLHC from st_accel_id_table
since LSM303DL series does not support spi interface
Fixes: d62511689d (iio: accel: Add STMicroelectronics accel driver)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
There are several locks issues when using buffer and direct polling
data at the same time. Use our own mutex for managing locking and
block simultaneous use of buffer and direct polling by using
iio_device_{claim/release}_direct_mode. This makes chip_config
enable bit obsolete, so delete it.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for active low interrupts (IRQF_TRIGGER_LOW and
IRQF_TRIGGER_FALLING). Configure the device as active high or low
according to the requested irq line.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use sysfs_match_string() helper instead of open coded variant.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use __sysfs_match_string() helper instead of open coded variant.
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Since index is always 0 replace devm_gpiod_get_index() by devm_gpiod_get().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
twl4030-madc.h is no longer used by anything outside of
the iio driver, so it can be merged into the driver.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This functionality is not used by the IIO subsystem. Due
to removal of legacy API it can also be removed.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
All madc users have been converted to IIO API, so drop the
legacy API. The function is still used inside of the driver.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Drop legacy twl4030_get_madc_conversion() method. It has been
used by drivers to get madc data before it conversion to IIO
API. There are no users in the mainline kernel anymore.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for STM32H7 Analog to Digital Converter. It has up
to 20 external channels, resolution ranges from 8 to 16bits.
Either bus or asynchronous adc clock may be used.
Add registers & bitfields definition. Also add new configuration
options to enter/exit powerdown and perform self-calibration.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
STM32F4 requires one clock per ADC instance for register access. But,
newer version of ADC hardware block have common bus clock for all
instances (per instance driver isn't responsible for getting it).
So, make it optional by default. Still, enforce it's required on STM32F4.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Prepare support for stm32h7 adc variant by introducing compatible
configuration data.
Move STM32F4 specific stuff to compatible data structure:
- registers & bit fields
- input channels data
- start/stop procedures
- trigger definitions
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Analog clock input is mandatory on stm32f4. But newer version of
ADC hardware block allow to select either bus clock or asynchronous
clock, for analog circuitry.
So, make it optional by default, but enforce clk presence on stm32f4.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
meson_sar_adc_clear_fifo passes a 0 as value-pointer to regmap_read().
In case of the meson-saradc driver this ends up in regmap_mmio_read(),
where the value-pointer is de-referenced unconditionally to assign the
value which was read.
Fix this by passing an actual pointer, even though all we want to do is
to discard the value.
As a side-effect this fixes a sparse warning ("Using plain integer as
NULL pointer") as reported by Paolo Cretaro.
Fixes: 3adbf34273 ("iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs")
Reported-by: Paolo Cretaro <paolocretaro@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When a multiplexer changes how an iio device behaves (for example
by feeding different signals to an ADC), this driver can be used
to create one virtual iio channel for each multiplexer state.
Depends on the generic multiplexer subsystem.
Cache any ext_info values from the parent iio channel, creating a private
copy of the ext_info attributes for each multiplexer state/channel.
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extend the inkern api with functions for reading and writing ext_info
of iio channels.
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error, the function devm_ioremap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should
be replaced with NULL test. Also add NULL test for iores.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
INA226/230/231 has integration times per voltage channel and common
averaging setting for both channels, while the INA219/220 only has a
combined integration time/averaging setting per channel.
Only expose the averaging attribute for the INA226, and expose the correct
integration times for the INA219.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fix sparse warning: Using plain integer as NULL pointer
Signed-off-by: Paolo Cretaro <paolocretaro@gmail.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fix sparse warning "symbol foo was not declared. Should it be static?"
for the following symbols:
mx23_lradc_adc_irq_names
mx28_lradc_adc_irq_names
iio_dev_attr_in_voltage0_scale_available
iio_dev_attr_in_voltage1_scale_available
iio_dev_attr_in_voltage2_scale_available
iio_dev_attr_in_voltage3_scale_available
iio_dev_attr_in_voltage4_scale_available
iio_dev_attr_in_voltage5_scale_available
iio_dev_attr_in_voltage6_scale_available
iio_dev_attr_in_voltage7_scale_available
iio_dev_attr_in_voltage10_scale_available
iio_dev_attr_in_voltage11_scale_available
iio_dev_attr_in_voltage12_scale_available
iio_dev_attr_in_voltage13_scale_available
iio_dev_attr_in_voltage14_scale_available
iio_dev_attr_in_voltage15_scale_available
Signed-off-by: Paolo Cretaro <paolocretaro@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This reverts commit 61305664a5.
This commit was applied prematurely and will break some existing
situations where the signal is inverted as part of voltage level
conversions.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Starting from MPU6500, accelerometer dlpf is set in a separate
register named ACCEL_CONFIG_2.
Add this new register in the map and set it for the corresponding
chips.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Flags for shared channel attributes should be set on all channels of a
channel set. I.e. SAMP_FREQUENCY and OVERSAMPLING_RATIO are set on the
in_voltage{0,1} channels, thus should be set on in_power, in_current.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
C syntax allows apersands when initializing structures fields with
function pointers, but in Linux sources ampersands are normally not used
in thix context.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This is no longer needed as the real problem was interrupt flags
not getting passed properly from device tree to the cpcap-core.c
mfd driver. This got fixed with commit ac89473213 ("mfd: cpcap:
Fix interrupt to use level interrupt") So let's remove ADC
interrupt specific the quirk.
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
It seems that "MC13783 Power Management and Audio Ciruit User's Guide"
MC1378UG.pdf documents several similar components as in the CPCAP PMIC.
Chapter "9.5.5 Die Temperature and UID" says that the die temperature
value is 282 at 25C with LSB of -1.14C. Converting CPCAP PMIC channel3
values with following seems to produce values that make sense for a
PMIC die:
temperature = 25000 + ((regval - 282) * 114)
As we don't have any other documentation, let's assume the die
temperature is unconfigured in the Motorola mapphone Linux kernel
and the current temperature conversion table should be only used
for the battery thermistor and not for the die temperature.
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Looking at the register dumps from Android kernel on droid 4, I noticed
the values with the mainline kernel don't match. Let's fix this by
initializing the ADC registers to what Android does.
For getting correct values from the battery thermistor, we need to
toggle the CPCAP_BIT_THERMBIAS_EN when measuring battery temperature
to get correct battery temperatures. And looks like we also need to
wait a little bit before reading the battery temperature as otherwise
the results are inaccurate.
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Two entirely new drivers in here plus the usual range of cleanups and features.
New device support
* ad5064
- add ltc2631, ltc2633 and ltc2635 support.
* bma180
- trivial support for bma250e (new id)
* hid-sensor-rotation
- add relative orientation and geometric orientation support.
* isl29028
- add isl29030 support (its effectively the same part from a driver point of
view)
* maxim_thermocouple
- add max31856 id.
* meson-saradc
- add meson8b SoC adc support.
* ti-adc084s021
- new driver and bindings.
* ti-adc108s102
- new driver and bindings.
Staging graduations
* isl29028
Features
* bma180
- ACPI enumeration for BMA250E which is used in various x86 tablets.
* hi8453
- add raw access rather than only events.
* hid-sensor-hub
- Implement batch mode in which we can set a threshold on the amount of time
between data coming from the fifos. This is the first device to do this
rather than use a watershed on the number of samples.
* hts221
- power management support
* lsm6dsx
- add system power management support.
* rpr0521
- sampling frequency read / write
* stm32-trigger
- add support for TRG02 triggers.
* tsl2583
- runtime power management support.
Cleanups
* core
- inkern: fix a double unlock in iio_read_available_channel_raw when raw
value doesn't appear to be raw (error path).
- fixup accidental sizeof pointer in iio_device_add_mask_type.
* docs
- fix an accidental duplicated line in sysfs-bus-iio-meas-spec.
* tools
- use local include/uapi headers to ensure always up to date.
- increase length of allowed trigger names.
* ad9834
- symbolic to octal permissions.
* ade7753
- symbolic to octal permissions.
- fix indentation
* ade7754
- symbolic to octal permissions.
* ade7758
- symbolic to octal permissions.
- ade7854
- symbolic to octal permissions.
* as3935
- move out of storm check to given consistent results for raw and processed
values.
* bmp280
- fix bme280 naming in Kconfig help.
* hi8435
- avoid garbage on event after enable.
- add missing in_voltage_sensing_mode_available to list possible enum options.
- handle the reset gpio with the obvious polarity rather than relying on
DT to provide it correctly.
* hid-sensors
- fix a wrong error path scrubbing of return values.
* hid-sensors-accel
- drop static on a local variable
* hid-sensors-rotation
- Add missing scale and offset property parsing support.
* ina2xx
- Fix a bad use of GENMASK and some typos and whitespace issues.
* isl29018
- only declare the ACPI table when ACPI is enabled.
* isl29028
- fix proximity sleep times.
* lsm6dsx
- replace ifdef CONFIG_PM with __maybe_unused to avoid the complexity of
dealing with the various PM config variables.
* meson-saradc
- mark meson_sar_adc_data static and const.
* rcar-gyroadc
- derive the interface clock speed from the fck clock on the basis they are
the same actual clock.
- drop the now unused if clock from the bindings.
* rpr0521
- disable sensor when marked as such rather than always enabling it.
- poweroff if probe fails and we can talk to device.
- make sure device powered off when it doesn't need to be on.
- use sizeof rather than hardcoded size on value read.
- whitespace fixup.
- reorder channel numbers ready for buffered support which didn't quite
make this pull request.
* st-accel
- fix platform data initialization to allow remove and reprobe.
* st-pressure
- fix platform data initialization to allow remove and reprobe.
* tsl2x7x
- S_IRUGO, S_IWUSR to octal values
- rename driver for consistency with more recent drivers
- drop FSF mailing address
- replace DEVICE_ATTR macros with the shorter DEVICE_ATTR_RW form and
relevant function renames.
* zpa2326
- report an error for consistency with other error paths.
-----BEGIN PGP SIGNATURE-----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=XLVY
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.13a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 4.13 cycle
Two entirely new drivers in here plus the usual range of cleanups and features.
New device support
* ad5064
- add ltc2631, ltc2633 and ltc2635 support.
* bma180
- trivial support for bma250e (new id)
* hid-sensor-rotation
- add relative orientation and geometric orientation support.
* isl29028
- add isl29030 support (its effectively the same part from a driver point of
view)
* maxim_thermocouple
- add max31856 id.
* meson-saradc
- add meson8b SoC adc support.
* ti-adc084s021
- new driver and bindings.
* ti-adc108s102
- new driver and bindings.
Staging graduations
* isl29028
Features
* bma180
- ACPI enumeration for BMA250E which is used in various x86 tablets.
* hi8453
- add raw access rather than only events.
* hid-sensor-hub
- Implement batch mode in which we can set a threshold on the amount of time
between data coming from the fifos. This is the first device to do this
rather than use a watershed on the number of samples.
* hts221
- power management support
* lsm6dsx
- add system power management support.
* rpr0521
- sampling frequency read / write
* stm32-trigger
- add support for TRG02 triggers.
* tsl2583
- runtime power management support.
Cleanups
* core
- inkern: fix a double unlock in iio_read_available_channel_raw when raw
value doesn't appear to be raw (error path).
- fixup accidental sizeof pointer in iio_device_add_mask_type.
* docs
- fix an accidental duplicated line in sysfs-bus-iio-meas-spec.
* tools
- use local include/uapi headers to ensure always up to date.
- increase length of allowed trigger names.
* ad9834
- symbolic to octal permissions.
* ade7753
- symbolic to octal permissions.
- fix indentation
* ade7754
- symbolic to octal permissions.
* ade7758
- symbolic to octal permissions.
- ade7854
- symbolic to octal permissions.
* as3935
- move out of storm check to given consistent results for raw and processed
values.
* bmp280
- fix bme280 naming in Kconfig help.
* hi8435
- avoid garbage on event after enable.
- add missing in_voltage_sensing_mode_available to list possible enum options.
- handle the reset gpio with the obvious polarity rather than relying on
DT to provide it correctly.
* hid-sensors
- fix a wrong error path scrubbing of return values.
* hid-sensors-accel
- drop static on a local variable
* hid-sensors-rotation
- Add missing scale and offset property parsing support.
* ina2xx
- Fix a bad use of GENMASK and some typos and whitespace issues.
* isl29018
- only declare the ACPI table when ACPI is enabled.
* isl29028
- fix proximity sleep times.
* lsm6dsx
- replace ifdef CONFIG_PM with __maybe_unused to avoid the complexity of
dealing with the various PM config variables.
* meson-saradc
- mark meson_sar_adc_data static and const.
* rcar-gyroadc
- derive the interface clock speed from the fck clock on the basis they are
the same actual clock.
- drop the now unused if clock from the bindings.
* rpr0521
- disable sensor when marked as such rather than always enabling it.
- poweroff if probe fails and we can talk to device.
- make sure device powered off when it doesn't need to be on.
- use sizeof rather than hardcoded size on value read.
- whitespace fixup.
- reorder channel numbers ready for buffered support which didn't quite
make this pull request.
* st-accel
- fix platform data initialization to allow remove and reprobe.
* st-pressure
- fix platform data initialization to allow remove and reprobe.
* tsl2x7x
- S_IRUGO, S_IWUSR to octal values
- rename driver for consistency with more recent drivers
- drop FSF mailing address
- replace DEVICE_ATTR macros with the shorter DEVICE_ATTR_RW form and
relevant function renames.
* zpa2326
- report an error for consistency with other error paths.
Matt finally set up the lightning storm he needed to test the as3935.
* core
- Fix a null pointer deference in iio_trigger_write_current when changing
from a non existent trigger to another non existent trigger.
* a3935
- Recalibrate the RCO after resume.
- Fix interrupt mask so that we actually get some interrupts.
- Use iio_trigger_poll_chained as we aren't in interrupt context.
* am335x
- Fix wrong allocation size provided for private data to iio_device_alloc.
* bcm_iproc
- Swapped primary and secondary isr handlers.
* ltr501
- Fix swapped als/ps register fields when enabling interrupts
* max9611
- Wrong scale factor for the shunt_resistor attribute.
* sun4-gpadc
- Module autoloading fixes by adding the device table declarations.
- Fix parent device being used in devm functions.
-----BEGIN PGP SIGNATURE-----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=luks
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.12a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes in the 4.12 cycle.
Matt finally set up the lightning storm he needed to test the as3935.
* core
- Fix a null pointer deference in iio_trigger_write_current when changing
from a non existent trigger to another non existent trigger.
* a3935
- Recalibrate the RCO after resume.
- Fix interrupt mask so that we actually get some interrupts.
- Use iio_trigger_poll_chained as we aren't in interrupt context.
* am335x
- Fix wrong allocation size provided for private data to iio_device_alloc.
* bcm_iproc
- Swapped primary and secondary isr handlers.
* ltr501
- Fix swapped als/ps register fields when enabling interrupts
* max9611
- Wrong scale factor for the shunt_resistor attribute.
* sun4-gpadc
- Module autoloading fixes by adding the device table declarations.
- Fix parent device being used in devm functions.
For the sake of DT binding stability, this IIO driver is a child of an
MFD driver for Allwinner A10, A13 and A31 because there already exists a
DT binding for this IP. The MFD driver has a DT node but the IIO driver
does not.
The IIO device registers the temperature sensor in the thermal framework
using the DT node of the parent, the MFD device, so the thermal
framework could match the phandle to the MFD device in the DT and the
struct device used to register in the thermal framework.
devm_thermal_zone_of_sensor_register was previously used to register the
thermal sensor with the parent struct device of the IIO device,
representing the MFD device. By doing so, we registered actually the
parent in the devm routine and not the actual IIO device.
This lead to the devm unregister function not being called when the IIO
module driver is removed. It resulted in the thermal framework still
polling the get_temp function of the IIO module while the device doesn't
exist anymore, thus generated a kernel panic.
Use the non-devm function instead and do the unregister manually in the
remove function.
Fixes: d1caa99055 ("iio: adc: add support for Allwinner SoCs ADC")
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Reported-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This is an upstream port of an IIO driver for the TI ADC108S102 and
ADC128S102. The former can be found on the Intel Galileo Gen2 and the
Siemens SIMATIC IOT2000. For those boards, ACPI-based enumeration is
included.
Due to the lack of regulators under ACPI, we hard-code the voltage
provided to the VA pin of the ADC to 5 V, the value used on Galileo and
IOT2000. For DT usage, the regulator "vref-supply" provides this
information. Note that DT usage has not been tested.
Original author: Bogdan Pricop <bogdan.pricop@emutex.com>
Ported from Intel Galileo Gen2 BSP to Intel Yocto kernel:
Todor Minchev <todor@minchev.co.uk>.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Get rid of #ifdef CONFIG_PM by adding __maybe_unused macro to
st_lsm6dsx_suspend and st_lsm6dsx_resume function declarations
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some x86 tablets use the BMA250E accelerometer, add support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The BMA250E adds a new fifo mode and is fully backwards compatible
with the BMA250, but with a different chip-id.
This commit adds support for it by adjusting the chip-id check and
otherwise treating it as a regular BMA250.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Move proximity channel from last to first in structs to avoid confusion
later with buffered triggers. Proximity data output is first in rpr0521
register map.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add sysfs read/write proximity offset feature. Offset is read/write from
sensor registers. Values are proximity raw 10-bit values. After applying
offset value, output values will be (measured_raw - offset_value). Output
values are unsigned so offset value doesn't make output negative.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Just whitespace change, no functional changes.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Changed magic number to sizeof() on value read.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Refactor _set_power_state(), _resume() and _suspend().
Enable measurement only when needed, not in _init(). System can suspend
during measurement and measurement is continued on resume.
Pm turns off measurement when both ps and als measurements are disabled for
2 seconds. During off-time the power save is 20-500mA, typically 180mA.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Set sensor measurement off after probe fail in pm_runtime_set_active() or
iio_device_register(). Without this change sensor measurement stays on
even though probe fails on these calls.
This is maybe rare case, but causes constant power drain without any
benefits when it happens. Power drain is 20-500uA, typically 180uA.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Sensor was marked enabled on each call even if the call was for disabling
sensor.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The register mapping for the IIO driver for the Liteon Light and Proximity
sensor LTR501 interrupt mode is interchanged (ALS/PS).
There is a register called INTERRUPT register (address 0x8F)
Bit 0 represents PS measurement trigger.
Bit 1 represents ALS measurement trigger.
This two bit fields are interchanged within the driver.
see datasheet page 24:
http://optoelectronics.liteon.com/upload/download/DS86-2012-0006/S_110_LTR-501ALS-01_PrelimDS_ver1%5B1%5D.pdf
Signed-off-by: Franziska Naepelt <franziska.naepelt@idt.com>
Fixes: 7ac702b314 ("iio: ltr501: Add interrupt support")
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The third argument of devm_request_threaded_irq() is the primary
handler. It is called in hardirq context and checks whether the
interrupt is relevant to the device. If the primary handler returns
IRQ_WAKE_THREAD, the secondary handler (a.k.a. handler thread) is
scheduled to run in process context.
bcm_iproc_adc.c uses the secondary handler as the primary one
and the other way around. So this patch fixes the same, along with
re-naming the secondary handler and primary handler names properly.
Tested on the BCM9583XX iProc SoC based boards.
Fixes: 4324c97ece ("iio: Add driver for Broadcom iproc-static-adc")
Reported-by: Pavel Roskin <plroskin@gmail.com>
Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reset GPIO is active low.
Currently driver uses gpiod_set_value(1) to clean reset, which depends
on device tree to contain GPIO_ACTIVE_HIGH - that does not match reality.
This fixes driver to use _raw version of gpiod_set_value() to enforce
active-low semantics despite of what's written in device tree. Allowing
device tree to override that only opens possibility for errors and does
not add any value.
Additionally, use _cansleep version to make things work with i2c-gpio
and other sleeping gpio drivers.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Possible values of sensing_mode are encoded with strings and actual
strings used are not obvious.
Provide a hint by enabling in_voltage_sensing_mode_available attribute.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Currently, driver generates events for channels if new reading differs
from previous one. This "previous value" is initialized to zero, which
results into event if value is constant-one.
Fix that by initializing "previous value" by reading at event enable
time.
This provides reliable sequence for userspace:
- enable event,
- AFTER THAT read current value,
- AFTER THAT each event will correspond to change.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
With current event-only driver, it is not possible for user space
application to know current senses if they don't change since
application starts.
Address that by adding raw access to channels.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes the following warning when building with clang:
drivers/iio/light/isl29018.c:808:36: error: variable
'isl29018_acpi_match' is not needed and will not be emitted
[-Werror,-Wunneeded-internal-declaration]
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
HID sensor hubs using Integrated Senor Hub (ISH) has added capability to
support batch mode. This allows host processor to go to sleep for extended
duration, while the sensor hub is storing samples in its internal buffers.
'Commit f4f4673b75 ("iio: add support for hardware fifo")' implements
feature in IIO core to implement such feature. This feature is used in
bmc150-accel-core.c to implement batch mode. This implementation allows
software device buffer watermark to be used as a hint to adjust hardware
FIFO.
But HID sensor hubs don't allow to change internal buffer size of FIFOs.
Instead an additional usage id to set "maximum report latency" is defined.
This allows host to go to sleep upto this latency period without getting
any report. Since there is no ABI to set this latency, a new attribute
"hwfifo_timeout" is added so that user mode can specify a latency.
This change checks presence of usage id to get/set maximum report latency
and if present, it will expose hwfifo_timeout.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds runtime power management support to the tsl2583 driver.
The device is powered off after two seconds of inactivity. Verified that
the driver still functions correctly using a TSL2581 hooked up to a
Raspberry Pi 2.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add system sleep power management support to hts221 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The power and current "shunt-resistor" attribute's 'show' function
displays the resistor value in milli-Ohms, while the ABI description
specifies it should be displayed in Ohms. Fix it.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds support for the Texas Instruments ADC084S021 ADC chip.
Signed-off-by: Mårten Lindahl <martenli@axis.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We should be allocating enough information for a tiadc_device struct
which is about 400 bytes but instead we allocate enough for a second
iio_dev struct which is over 2000 bytes.
Fixes: fea89e2dfc ("iio: adc: ti_am335x_adc: use variable names for sizeof() operator")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The Linear Technology LTC2631, LTC2633 and LTC2635 are very similar
to the AD5064 device, in particular the LTC2627.
This patch adds support for those devices. Only the LTC2633 has been
tested, which is the 2-channel variant. The LTC2631 is the 1-channel,
and the LTC2635 the 4-channel version. The actual DAC resolution depends
on the exact chip type and can be 12, 10 or 8 bits, using the upper bits
so this has no effect on the register map. The internal reference is set
to 2.5V on "L" versions, and it's 4.096V for "H" versions.
Datasheets:
LTC2631: http://www.linear.com/docs/26553
LTC2633: http://www.linear.com/docs/39529
LTC2635: http://www.linear.com/docs/28754
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
If the timeout-case prints a warning message then probably the interrupted
case should also. Further, wait_for_completion_interruptible_timeout()
returns long not int.
Fixes: commit 03b262f2bb ("iio:pressure: initial zpa2326 barometer support")
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
-----BEGIN PGP SIGNATURE-----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=lbS7
-----END PGP SIGNATURE-----
Merge tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull hw lockdown support from David Howells:
"Annotation of module parameters that configure hardware resources
including ioports, iomem addresses, irq lines and dma channels.
This allows a future patch to prohibit the use of such module
parameters to prevent that hardware from being abused to gain access
to the running kernel image as part of locking the kernel down under
UEFI secure boot conditions.
Annotations are made by changing:
module_param(n, t, p)
module_param_named(n, v, t, p)
module_param_array(n, t, m, p)
to:
module_param_hw(n, t, hwtype, p)
module_param_hw_named(n, v, t, hwtype, p)
module_param_hw_array(n, t, hwtype, m, p)
where the module parameter refers to a hardware setting
hwtype specifies the type of the resource being configured. This can
be one of:
ioport Module parameter configures an I/O port
iomem Module parameter configures an I/O mem address
ioport_or_iomem Module parameter could be either (runtime set)
irq Module parameter configures an I/O port
dma Module parameter configures a DMA channel
dma_addr Module parameter configures a DMA buffer address
other Module parameter configures some other value
Note that the hwtype is compile checked, but not currently stored (the
lockdown code probably won't require it). It is, however, there for
future use.
A bonus is that the hwtype can also be used for grepping.
The intention is for the kernel to ignore or reject attempts to set
annotated module parameters if lockdown is enabled. This applies to
options passed on the boot command line, passed to insmod/modprobe or
direct twiddling in /sys/module/ parameter files.
The module initialisation then needs to handle the parameter not being
set, by (1) giving an error, (2) probing for a value or (3) using a
reasonable default.
What I can't do is just reject a module out of hand because it may
take a hardware setting in the module parameters. Some important
modules, some ipmi stuff for instance, both probe for hardware and
allow hardware to be manually specified; if the driver is aborts with
any error, you don't get any ipmi hardware.
Further, trying to do this entirely in the module initialisation code
doesn't protect against sysfs twiddling.
[!] Note that in and of itself, this series of patches should have no
effect on the the size of the kernel or code execution - that is
left to a patch in the next series to effect. It does mark
annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
an already existing field"
* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
Annotate hardware config module parameters in sound/pci/
Annotate hardware config module parameters in sound/oss/
Annotate hardware config module parameters in sound/isa/
Annotate hardware config module parameters in sound/drivers/
Annotate hardware config module parameters in fs/pstore/
Annotate hardware config module parameters in drivers/watchdog/
Annotate hardware config module parameters in drivers/video/
Annotate hardware config module parameters in drivers/tty/
Annotate hardware config module parameters in drivers/staging/vme/
Annotate hardware config module parameters in drivers/staging/speakup/
Annotate hardware config module parameters in drivers/staging/media/
Annotate hardware config module parameters in drivers/scsi/
Annotate hardware config module parameters in drivers/pcmcia/
Annotate hardware config module parameters in drivers/pci/hotplug/
Annotate hardware config module parameters in drivers/parport/
Annotate hardware config module parameters in drivers/net/wireless/
Annotate hardware config module parameters in drivers/net/wan/
Annotate hardware config module parameters in drivers/net/irda/
Annotate hardware config module parameters in drivers/net/hamradio/
Annotate hardware config module parameters in drivers/net/ethernet/
...
Add support for TRGO2 trigger that can be found on STM32F7.
Add additional master modes supported by TRGO2.
Register additional "tim[1/8]_trgo2" triggers for timer1 & timer8.
Detect TRGO2 timer capability (master mode selection 2).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
If the driver is built as a module, it won't be autloaded if the devices
are registered via OF code because the OF device table
entries are not exported as aliases
Before the patch:
$ modinfo drivers/iio/adc/sun4i-gpadc-iio.ko | grep alias
alias: platform:sun6i-a31-gpadc-iio
alias: platform:sun5i-a13-gpadc-iio
alias: platform:sun4i-a10-gpadc-iio
After the patch:
$ modinfo drivers/iio/adc/sun4i-gpadc-iio.ko | grep alias
alias: of:N*T*Callwinner,sun8i-a33-thsC*
alias: of:N*T*Callwinner,sun8i-a33-ths
alias: platform:sun6i-a31-gpadc-iio
alias: platform:sun5i-a13-gpadc-iio
alias: platform:sun4i-a10-gpadc-iio
Signed-off-by: Eduardo Molinas <edu.molinas@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
If the driver is built as a module, it won't be autloaded if the devices
are registered via PLATFORM code because the PLATFORM device table
entries are not exported as aliases
Before the patch:
$ modinfo drivers/iio/adc/sun4i-gpadc-iio.ko | grep alias
$
After the patch:
$ modinfo drivers/iio/adc/sun4i-gpadc-iio.ko | grep alias
alias: platform:sun6i-a31-gpadc-iio
alias: platform:sun5i-a13-gpadc-iio
alias: platform:sun4i-a10-gpadc-iio
Signed-off-by: Eduardo Molinas <edu.molinas@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Commit 7906dd52c5 ("iio: ina2xx: Fix whitespace and re-order code")
changed the register number of the MASK_ENABLE register from 0x06 to the
value equivalent GENMASK(2,1), although its no mask.
Also fix a typo (INA2_6_6 instead of INA2_2_6), and use the datasheet
name ("Mask/Enable") for the register number define.
Fix bad indentation for channel attributes.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Drop static on a local variable, when the variable is initialized before
use, on every possible execution path through the function. The static has
no benefit, and dropping it reduces the code size.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
// </smpl>
The change in code size is indicates by the following output from the size
command.
before:
text data bss dec hex filename
3879 512 8 4399 112f drivers/iio/accel/hid-sensor-accel-3d.o
after:
text data bss dec hex filename
3863 512 0 4375 1117 drivers/iio/accel/hid-sensor-accel-3d.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Using iio_trigger_poll() can oops when multiple interrupts
happen before the first is handled.
Use iio_trigger_poll_chained() instead and use the timestamp
when processed, since it will be in theory be 2 ms max latency.
Fixes: 24ddb0e4bb ("iio: Add AS3935 lightning sensor support")
Cc: stable@vger.kernel.org
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
MAX31856 is register equivalent to the MAX31855 but suppports J, N, R,
S, T, E and B type thermocouples in addition to K-type.
Data conversion for the various types happens transparently to the driver
via probe type detection, and a LUT on the sensor.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Meson GX SoCs however use some magic bits to prevent simultaneous (=
conflicting, because only consumer should use the FIFO buffer with the
ADC results) usage by the Linux kernel and the bootloader (the BL30
bootloader uses the SAR ADC to read the CPU temperature).
This patch changes guards all BL30 functionality so it is skipped on
SoCs which don't have it. Since the hardware itself doesn't know whether
BL30 is available the internal meson_sar_adc_data is extended so this
information can be provided per of_device_id.data inside the driver.
Additionally the clocks "adc_clk" and "adc_sel" are not provided by the
clock-controller itself. "adc_sel" is not available at all. "adc_clk"
is provided by the SAR ADC IP block itself on Meson8b (and earlier).
This is already supported by the meson_saradc driver.
Finally this introduces new of_device_ids for the Meson8 and Meson8b
SoCs so the driver can be wired up in the corresponding DT.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
These are only passed as of_device_id.data and never modified. Thus we
can mark them as static const, just like the of_device_id instances
where they are used.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add orientation sensor "scale" and "offset" parse support.
These two properties are needed for exponent data conversion.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Xu Even <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Geomagnetic orientation(AM) sensor is one kind of orientation 6dof sensor.
It gives the device rotation in respect to the earth center and the
magnetic north. The sensor is implemented through use of an accelerometer
and magnetometer do not use gyroscope. It is a standard HID sensor.
More information can be found in:
http://www.usb.org/developers/hidpage/HUTRR59_-_Usages_for_Wearables.pdf
Geomagnetic orientation(AM) sensor and dev rotation sensor have same
channel and share channel usage id. So the most of the code for relative
orientation sensor can be reused.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Relative orientation(AG) sensor is a 6dof orientation sensor,
it depends on acceleration and gyroscope sensor data. It gives
a quaternion describing the orientation of the device relative
to an initial orientation. It is a standard HID sensor.
More information can be found in:
http://www.usb.org/developers/hidpage/HUTRR59_-_Usages_for_Wearables.pdf
Relative orientation(AG) sensor and dev rotation sensor have same
channels and share channel usage id. So the most of the code for
relative orientation sensor can be reused.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Xu Even <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Here is the big staging tree update for 4.12-rc1. And it's a big one,
adding about 350k new lines of crap^Wcode, mostly all in a big dump of
media drivers from Intel. But there's other new drivers in here as
well, yet-another-wifi driver, new IIO drivers, and a new crypto
accelerator. We also deleted a bunch of stuff, mostly in patch
cleanups, but also the Android ION code has shrunk a lot, and the
Android low memory killer driver was finally deleted, much to the
celebration of the -mm developers.
All of these have been in linux-next with a few build issues that will
show up when you merge to your tree, I'll follow up with fixes for those
after this gets merged.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWQzzlQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylNMgCcD+GoaF/Ml7YnULRl2GG/526II78AnitZ8qjd
rPqeowMIewYu9fgckLUc
=7rzO
-----END PGP SIGNATURE-----
Merge tag 'staging-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO updates from Greg KH:
"Here is the big staging tree update for 4.12-rc1.
It's a big one, adding about 350k new lines of crap^Wcode, mostly all
in a big dump of media drivers from Intel. But there's other new
drivers in here as well, yet-another-wifi driver, new IIO drivers, and
a new crypto accelerator.
We also deleted a bunch of stuff, mostly in patch cleanups, but also
the Android ION code has shrunk a lot, and the Android low memory
killer driver was finally deleted, much to the celebration of the -mm
developers.
All of these have been in linux-next with a few build issues that will
show up when you merge to your tree"
Merge conflicts in the new rtl8723bs driver (due to the wifi changes
this merge window) handled as per linux-next, courtesy of Stephen
Rothwell.
* tag 'staging-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1182 commits)
staging: fsl-mc/dpio: add cpu <--> LE conversion for dpaa2_fd
staging: ks7010: remove line continuations in quoted strings
staging: vt6656: use tabs instead of spaces
staging: android: ion: Fix unnecessary initialization of static variable
staging: media: atomisp: fix range checking on clk_num
staging: media: atomisp: fix misspelled word in comment
staging: media: atomisp: kmap() can't fail
staging: atomisp: remove #ifdef for runtime PM functions
staging: atomisp: satm include directory is gone
atomisp: remove some more unused files
atomisp: remove hmm_load/store/clear indirections
atomisp: kill off mmgr_free
atomisp: clean up the hmm init/cleanup indirections
atomisp: handle allocation calls before init in the hmm layer
staging: fsl-dpaa2/eth: Add maintainer for Ethernet driver
staging: fsl-dpaa2/eth: Add TODO file
staging: fsl-dpaa2/eth: Add trace points
staging: fsl-dpaa2/eth: Add driver specific stats
staging: fsl-dpaa2/eth: Add ethtool support
staging: fsl-dpaa2/eth: Add Freescale DPAA2 Ethernet driver
...
Here is the big set of new char/misc driver drivers and features for
4.12-rc1.
There's lots of new drivers added this time around, new firmware drivers
from Google, more auxdisplay drivers, extcon drivers, fpga drivers, and
a bunch of other driver updates. Nothing major, except if you happen to
have the hardware for these drivers, and then you will be happy :)
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWQvAgg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yknsACgzkAeyz16Z97J3UTaeejbR7nKUCAAoKY4WEHY
8O9f9pr9gj8GMBwxeZQa
=OIfB
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of new char/misc driver drivers and features for
4.12-rc1.
There's lots of new drivers added this time around, new firmware
drivers from Google, more auxdisplay drivers, extcon drivers, fpga
drivers, and a bunch of other driver updates. Nothing major, except if
you happen to have the hardware for these drivers, and then you will
be happy :)
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (136 commits)
firmware: google memconsole: Fix return value check in platform_memconsole_init()
firmware: Google VPD: Fix return value check in vpd_platform_init()
goldfish_pipe: fix build warning about using too much stack.
goldfish_pipe: An implementation of more parallel pipe
fpga fr br: update supported version numbers
fpga: region: release FPGA region reference in error path
fpga altera-hps2fpga: disable/unprepare clock on error in alt_fpga_bridge_probe()
mei: drop the TODO from samples
firmware: Google VPD sysfs driver
firmware: Google VPD: import lib_vpd source files
misc: lkdtm: Add volatile to intentional NULL pointer reference
eeprom: idt_89hpesx: Add OF device ID table
misc: ds1682: Add OF device ID table
misc: tsl2550: Add OF device ID table
w1: Remove unneeded use of assert() and remove w1_log.h
w1: Use kernel common min() implementation
uio_mf624: Align memory regions to page size and set correct offsets
uio_mf624: Refactor memory info initialization
uio: Allow handling of non page-aligned memory regions
hangcheck-timer: Fix typo in comment
...
Add system sleep power management support to st_lsm6dsx driver.
In particular during suspend phase each sensor is disabled and
hw fifo is configured in bypass in order to avoid subsequent
I/O operations. The patch has been tested on HiKey board device
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Remove static qualifier from st_lsm6dsx_flush_fifo() and
st_lsm6dsx_set_fifo_mode() in order to use them in system sleep pm support
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
isl29030 is basically the same chip. The only difference
is the chip's first pin. For isl29028 its named ADDR0 and
can be used to change the chip's i2c address. For isl29030
on the other hand that pin is named Ials and is an analog
current output proportional to ALS/IR. This change is
irrelevant for the Linux driver.
This has been tested on Motorola Droid 4.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
AS3935 interrupt mask has been incorrect so valid lightning events
would never trigger an buffer event. Also noise interrupt should be
BIT(0).
Fixes: 24ddb0e4bb ("iio: Add AS3935 lightning sensor support")
CC: stable@vger.kernel.org
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The X-Powers AXP20X and AXP22X PMICs have multiple ADCs. They expose the
battery voltage, battery charge and discharge currents, AC-in and VBUS
voltages and currents, 2 GPIOs muxable in ADC mode and PMIC temperature.
This adds support for most of AXP20X and AXP22X ADCs.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move out of storm check to apply to IIO_CHAN_INFO_RAW so the reported
results are constant between the former and the IIO_CHAN_INFO_PROCESSED
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Ensure that when an invalid value in ret or value is found -EINVAL
is returned. A previous commit broke the way the return error is
being returned and instead caused the return code in ret to be
re-assigned rather than be returned.
Fixes: 5d9854eaea ("iio: hid-sensor: Store restore poll and hysteresis on S3")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Pointer size is variours in different system, say 32bit for 4 and 64bit
for 8. The 'sizeof(infomask)' may lead to wrong bit numbers.
Signed-off-by: Orson Zhai <orson.zhai@spreadtrum.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The "if" interface clock speed is actually derived from the "fck"
block clock, as in the hardware they are the same clock. Drop the
incorrect second "if" clock and get the clock speed from "fck".
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: linux-renesas-soc@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
According to the datasheet the RCO must be recalibrated
on every power-on-reset. Also remove mutex locking in the
calibration function since callers other than the probe
function (which doesn't need it) will have a lock.
Fixes: 24ddb0e4bb ("iio: Add AS3935 lightning sensor support")
Cc: George McCollister <george.mccollister@gmail.com>
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch fixes the sensor platform data initialisation for st_pressure
and st_accel device drivers. Without this patch, the driver fails to
register the sensors when the user removes and re-loads the driver.
1. Unload the kernel modules for st_pressure
$ sudo rmmod st_pressure_i2c
$ sudo rmmod st_pressure
2. Re-load the driver
$ sudo insmod st_pressure
$ sudo insmod st_pressure_i2c
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Move ISL29028 ALS / Proximity Sensor out of staging and into mainline.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Avoid this smatch error:
drivers/iio/inkern.c:751 iio_read_avail_channel_raw() error: double unlock 'mutex:&chan->indio_dev->info_exist_lock'
Fixes: 00c5f80c2f ("iio: inkern: add helpers to query available values from channels")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Bosch BME280 is a combined pressure and humidity sensor
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When the kernel is running in secure boot mode, we lock down the kernel to
prevent userspace from modifying the running kernel image. Whilst this
includes prohibiting access to things like /dev/mem, it must also prevent
access by means of configuring driver modules in such a way as to cause a
device to access or modify the kernel image.
To this end, annotate module_param* statements that refer to hardware
configuration and indicate for future reference what type of parameter they
specify. The parameter parser in the core sees this information and can
skip such parameters with an error message if the kernel is locked down.
The module initialisation then runs as normal, but just sees whatever the
default values for those parameters is.
Note that we do still need to do the module initialisation because some
drivers have viable defaults set in case parameters aren't specified and
some drivers support automatic configuration (e.g. PNP or PCI) in addition
to manually coded parameters.
This patch annotates drivers in drivers/iio/.
Suggested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
cc: linux-iio@vger.kernel.org
As these are rather late in the cycle, they may sneak over into 4.12.
There is a fix for a regression caused by another fix (hid sensors
hardware seems to vary a lot in how various corner cases are handled).
* ad7303
- fix channel description. Numeric values were being passed as characters
presumably leading to garbage from the userspace interface.
* as3935
- the write data macro was wrong so fix it.
* bmp280
- incorrect handling of negative values as being unsigned broke humidity
calculation.
* hid-sensor
- Restore the poll and hysteresis values after resume as some hardware
doesn't do it.
* stm32-trigger
- buglet in reading the sampling frequency
-----BEGIN PGP SIGNATURE-----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=H5KS
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.11e' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Fifth set of IIO fixes for the 4.11 cycle.
As these are rather late in the cycle, they may sneak over into 4.12.
There is a fix for a regression caused by another fix (hid sensors
hardware seems to vary a lot in how various corner cases are handled).
* ad7303
- fix channel description. Numeric values were being passed as characters
presumably leading to garbage from the userspace interface.
* as3935
- the write data macro was wrong so fix it.
* bmp280
- incorrect handling of negative values as being unsigned broke humidity
calculation.
* hid-sensor
- Restore the poll and hysteresis values after resume as some hardware
doesn't do it.
* stm32-trigger
- buglet in reading the sampling frequency
New device support
* max1117, 1118 and 1119
- new ADC driver
* max9611
- new ADC driver
* pm8xxx hk/xoadc
- new driver with some shared features broken out from the SPMI vadc.
* sun4i-gpadc
- A33 thermal sensor support (with associated rework)
* stm32-dac
- new driver and bindings
* stm32 trigger
- enable support of quadrature encoder device and counter modes
Features
* apds9960
- use the runtime pm for normal suspend
* stm32-adc
- add opition to sest resolution via devicetree
* xoadc
- augment DT bindings to deal with some weird mux cases
Cleanups
* ad5933
- protect direct mode using claim and release helpers
* ade7759
- S_IRUGO and friends to octal in two goes
* adis16203
- drop unnecessary brackets
* hid-sensor
- fix unbalanced pm_runtieme_enable error when probing after remove
* lsm6dsx
- use actual part numbers for device name when known
- simplify data read pin parsing
* mpu3050
- avoid double reporting errors
-----BEGIN PGP SIGNATURE-----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=zHqs
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.12d' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Fourth set of IIO new device support, features and cleanups for the 4.12 cycle
New device support
* max1117, 1118 and 1119
- new ADC driver
* max9611
- new ADC driver
* pm8xxx hk/xoadc
- new driver with some shared features broken out from the SPMI vadc.
* sun4i-gpadc
- A33 thermal sensor support (with associated rework)
* stm32-dac
- new driver and bindings
* stm32 trigger
- enable support of quadrature encoder device and counter modes
Features
* apds9960
- use the runtime pm for normal suspend
* stm32-adc
- add opition to sest resolution via devicetree
* xoadc
- augment DT bindings to deal with some weird mux cases
Cleanups
* ad5933
- protect direct mode using claim and release helpers
* ade7759
- S_IRUGO and friends to octal in two goes
* adis16203
- drop unnecessary brackets
* hid-sensor
- fix unbalanced pm_runtieme_enable error when probing after remove
* lsm6dsx
- use actual part numbers for device name when known
- simplify data read pin parsing
* mpu3050
- avoid double reporting errors
While calculating the compensation of the humidity there are negative values
interpreted as unsigned because of unsigned variables used. These values as
well as the constants need to be casted to signed as indicated by the
documentation of the sensor.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
APDS9960 can safely force runtime suspend if the system wants
to enter system-wide suspend
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for STMicroelectronics STM32 DAC. It's a 12-bit, voltage
output digital-to-analog converter. It has two output channels, each
with its own converter.
It supports 8 bits or 12bits left/right aligned data format. Only
12bits right-aligned is used here. It has built-in noise or
triangle waveform generator, and supports external triggers for
conversions.
Each channel can be used independently, with separate trigger, then
separate IIO devices are used to handle this. Core driver is intended
to share common resources such as clock, reset, reference voltage and
registers.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Simplify st_lsm6dsx_of_get_drdy_pin routine since of_property_read_u32
error conditions are already managed in st_lsm6dsx_get_drdy_reg()
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds max1117/max1118/max1119 8-bit, dual-channel ADC driver.
This new driver uses the zero length spi_transfers with the cs_change
flag set and/or the non-zero delay_usecs.
1. The zero length transfer with the spi_transfer.cs_change set is
required in order to select CH1. The chip select line must be brought
high and low again without transfer.
2. The zero length transfer with the spi_transfer.delay_usecs > 0 is
required for waiting the conversion to be complete. The conversion
begins with the falling edge of the chip select. During the conversion
process, SCLK is ignored.
These two usages are unusual. But the spi controller drivers that use
a default implementation of transfer_one_message() are likely to work.
(I've tested this adc driver with spi-omap2-mcspi and spi-xilinx)
On the other hand, some spi controller drivers that have their own
transfer_one_message() may not work. But at least for the zero length
transfer with delay_usecs > 0, I'm proposing a new testcase for the
spi-loopback-test that can test whether the delay_usecs setting has
taken effect.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Device counting could be controlled by the level or the edges of
a trigger.
in_count0_enable_mode attibute allow to set the control mode.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
One of the features of STM32 trigger hardware block is a quadrature
encoder that can counts up/down depending of the levels and edges
of the selected external pins.
This patch allow to read/write the counter, get it direction,
set/get quadrature modes and get scale factor.
When counting up preset value is the limit of the counter.
When counting down the counter start from preset value down to 0.
This preset value could be set/get by using
/sys/bus/iio/devices/iio:deviceX/in_count0_preset attribute.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Reviewed-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
AS3935_WRITE_DATA macro bit is incorrect and the actual write
sequence is two leading zeros.
Cc: George McCollister <george.mccollister@gmail.com>
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
realbits, storagebits and shift should be numbers, not ASCII characters.
Signed-off-by: Pavel Roskin <plroskin@gmail.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use the correct chip name (e.g. lsm6dsm) as suffix for iio_dev name
instead of a generic one (lsm6dsx)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The Qualcomm PM8xxx PMICs contain a simpler ADC than its
successors (already in the kernel as qcom-spmi-vadc.c):
the HK/XO ADC (Housekeeping/Chrystal oscillator ADC).
As far as I can understand this is equal to the PMICs
using SSBI transport and encompass PM8018, PM8038,
PM8058, and PM8921, so this is shortly named PM8xxx.
This ADC monitors a bunch of on-board voltages and the die
temperature of the PMIC itself, but it can also be routed
to convert a few external MPPs (multi-purpose pins). On
the APQ8060 DragonBoard this feature is used to let this
ADC convert an analog ALS (Ambient Light Sensor) voltage
signal from a Capella CM3605 ALS into a LUX value.
Developed and tested with APQ8060 DragonBoard based on
Ivan's driver and Rama Krishna's patches. The SPMI VADC
driver is quite different, but share enough minor
functionality that I have split out to the common file
in a previous patch.
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: Ivan T. Ivanov <iivanov.xz@gmail.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Rama Krishna Phani A <rphani@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The SPMI VADC and the earlier XOADC share a subset of
common code, so to be able to use the same code in both
drivers, we break out a separate file with the common code,
prefix exported functions that are no longer static with
qcom_* and bake an object qcom-spmi-vadc.o that contains both
files: qcom-vadc-common.o and qcom-spmi-vadc-core.o.
As we need to follow the procedure for making a kernel module
or compiled in object from several files, but still want to
produce the same module name, rename the qcom-spmi-vadc.c
file to qcom-spmi-vadc-core.c so we can bake the two objects
into qcom-spmi-vadc.o
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: Ivan T. Ivanov <iivanov.xz@gmail.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Rama Krishna Phani A <rphani@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds support for the Allwinner A33 thermal sensor.
Unlike the A10, A13 and A31, the Allwinner A33 only has one channel
which is dedicated to the thermal sensor. Moreover, its thermal sensor
does not generate interruptions, thus we only need to directly read the
register storing the temperature value.
The MFD used by the A10, A13 and A31, was created to avoid breaking the
DT binding, but since the nodes for the ADC weren't there for the A33,
it is not needed.
Though the A33 does not have an internal ADC, it has a thermal sensor
which shares the same registers with GPADC of the already supported SoCs
and almost the same bits, for the same purpose (thermal sensor).
The thermal sensor behaves exactly the same (except the presence of
interrupts or not) on the different SoCs.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This moves code used in MFD probing to a new sun4i_gpadc_probe_mfd
function.
This driver was initially written for A10, A13 and A31 SoCs which
already had a DT binding for this IP, thus we needed to use an MFD to
probe the different drivers without changing the DT binding of these
SoCs.
For SoCs that will require to create a DT binding for this IP, we can
avoid using an MFD, thus we need two separate functions: one for probing
via MFD and one for probing without MFD.
This split the code specific to MFD probing in a function separated from
the driver probe function.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When prescaler (PSC) is 0, it means div factor is 1: counter clock
frequency is equal to input clk / (PSC + 1).
When reload value is 8 for example, counter counts 9 cycles, from 0 to 8.
This is handled in frequency write routine, by writing respectively:
- prescaler - 1 to PSC
- reload value - 1 to ARR
This fix does the opposite when reading the frequency from PSC and ARR:
- prescaler is PSC + 1
- reload value is ARR + 1
Thus, PSC may be 0, depending on requested sampling frequency (div 1).
In this case, reading freq wrongly reports 0, instead of computing and
reporting correct value.
Remove test on !psc and !arr.
Small test on stm32f4 (example on tim1_trgo), before this fix:
$ cd /sys/bus/iio/devices/triggerX
$ echo 10000 > sampling_frequency
$ cat sampling_frequency
0
After this fix:
$ echo 10000 > sampling_frequency
$ cat sampling_frequency
10000
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When a hid sensor module is removed and modprobed again we see
error for unbalanced pm_runtime. This issue is caused by not
deactivating runtime PM on removal. So on modprobe again when
activated again, this will print this error.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This change undo the change done by 'commit 3bec247474
("iio: hid-sensor-trigger: Change get poll value function order to avoid
sensor properties losing after resume from S3")' as this breaks some
USB/i2c sensor hubs.
Instead of relying on HW for restoring poll and hysteresis, driver stores
and restores on resume (S3). In this way user space modified settings are
not lost for any kind of sensor hub behavior.
In this change, whenever user space modifies sampling frequency or
hysteresis driver will get the feature value from the hub and store in the
per device hid_sensor_common data structure. On resume callback from S3,
system will set the feature to sensor hub, if user space ever modified the
feature value.
Fixes: 3bec247474 ("iio: hid-sensor-trigger: Change get poll value function order to avoid sensor properties losing after resume from S3")
Reported-by: Ritesh Raj Sarraf <rrs@researchut.com>
Tested-by: Ritesh Raj Sarraf <rrs@researchut.com>
Tested-by: Song, Hongyan <hongyan.song@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
stm32 adc supports several resolution. Add 'assigned-resolution-bits'
dt optional property to set it. Default to maximum resolution in case
it isn't set.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
i2c_mux_add_adapter already logs a message on failure.
Signed-off-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Somewhat dominated in patch numbers of last of the outreachy application
window related patches (they are still coming, despite window being closed
which is good to see!)
Good set of new drivers as well.
New device support
* ASPEED ADC
- new driver
* cpcap PMIC ADC
- new driver
* hid-humidity
- driver for HID compatible humidity sensors.
* ltc2497 ADC
- new driver
* mpu6050
- bring bindings up to date and add trivial support for 9250
* rockchip-saradc
- update bindings to cover rk3328
* vl6180 light, proximity and time of flight sensor.
- new driver
Features
* meson-saradc
- add calibration
Cleanup and minor fixes
* ad5504
- constify attribute_group structure
- drop casting of void *
* ad7150
- replace some shifts of 1 by BIT macro usage
* ad7152
- blank lines between function definitions
* ad7280a
- octal permissions.
* ad7606
- replace use of core mlock mutex with a local lock
* ad7746
- replace some shifts of 1 by BIT macro usage
- function parameter alignment
- drop some excessive brackets (introduced in last pull request)
* ad7753
- white space cleanup
* ad7754
- includes in alphabetical order and groupped appropriately.
- change from missuse of internal mlock mutex to using the buffer lock to
also protect values during frequency update.
* ad779x
- constify attribute_group structures
* ad9832
- octal permissions
* adis16060
- remove use of core mlock mutex in favour of adding a local
_spi_write_then_read which can use the local buffer protection lock.
- fix naming of above function.
* adis16203
- remove locking during reads of calibbias that doesn't protect anything
not protected elsewhere.
* adis16209
- remove unnecessary braces in single statement if
* adis16240
- remove unnecessary braces in single statement if
* adt7136
- drop excess blank lines and put some in between functions.
* ams-iaq
- replace comma with semi colon. Not actual bug, just unusual syntax.
* apds9960
- constify attribute group structure
* as3935
- constify attribute group structure
* bm1750
- constify attribute group structure
* cros_ec
- devm version of triggered buffer setup to simplify code.
* exynos
- drop casting of void *
* hdc100x
- constify attribute_group structure
* hid-accel
- fix wrong scale for newly introduced gravity sensor.
* hts221
- drop casting of void *
* hx711
- constify attribute_group structure
* imx7d_adc
- drop casting of void *
* lm35333
- constify attribute_group structure
* lsm6dsx
- drop casting of void *
- hold ODR configuration until enabling to avoid a race condition.
* max1027
- drop casting of void *
* max11100
- fix a comma where semicolon was intended (no actual bug, just odd)
* max1363
- constify attribute_group structure
* ms sensors
- drop casting of void *
* rockchip_saradc
- drop casting of void *
* sun4i-gpadc
- fix missing dependency on THERMAL or presence of stubs (issue only
introduced in pervious set)
- drop casting of void *
* tsl2x7x
- fix wrong standard deviation calc. Note these aren't actually used for
anything at the moment so bug didn't really matter.
- constify attribute group structure.
* vf610adc
- drop casting of void *
* vz89x
- replace comma with semicolon. Not actual bug, just odd syntax.
* zpa2326
- drop casting of void *
-----BEGIN PGP SIGNATURE-----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=YYdq
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.12c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Third set of new device support, cleanups and features for IIO in the 4.12 cycle
Somewhat dominated in patch numbers of last of the outreachy application
window related patches (they are still coming, despite window being closed
which is good to see!)
Good set of new drivers as well.
New device support
* ASPEED ADC
- new driver
* cpcap PMIC ADC
- new driver
* hid-humidity
- driver for HID compatible humidity sensors.
* ltc2497 ADC
- new driver
* mpu6050
- bring bindings up to date and add trivial support for 9250
* rockchip-saradc
- update bindings to cover rk3328
* vl6180 light, proximity and time of flight sensor.
- new driver
Features
* meson-saradc
- add calibration
Cleanup and minor fixes
* ad5504
- constify attribute_group structure
- drop casting of void *
* ad7150
- replace some shifts of 1 by BIT macro usage
* ad7152
- blank lines between function definitions
* ad7280a
- octal permissions.
* ad7606
- replace use of core mlock mutex with a local lock
* ad7746
- replace some shifts of 1 by BIT macro usage
- function parameter alignment
- drop some excessive brackets (introduced in last pull request)
* ad7753
- white space cleanup
* ad7754
- includes in alphabetical order and groupped appropriately.
- change from missuse of internal mlock mutex to using the buffer lock to
also protect values during frequency update.
* ad779x
- constify attribute_group structures
* ad9832
- octal permissions
* adis16060
- remove use of core mlock mutex in favour of adding a local
_spi_write_then_read which can use the local buffer protection lock.
- fix naming of above function.
* adis16203
- remove locking during reads of calibbias that doesn't protect anything
not protected elsewhere.
* adis16209
- remove unnecessary braces in single statement if
* adis16240
- remove unnecessary braces in single statement if
* adt7136
- drop excess blank lines and put some in between functions.
* ams-iaq
- replace comma with semi colon. Not actual bug, just unusual syntax.
* apds9960
- constify attribute group structure
* as3935
- constify attribute group structure
* bm1750
- constify attribute group structure
* cros_ec
- devm version of triggered buffer setup to simplify code.
* exynos
- drop casting of void *
* hdc100x
- constify attribute_group structure
* hid-accel
- fix wrong scale for newly introduced gravity sensor.
* hts221
- drop casting of void *
* hx711
- constify attribute_group structure
* imx7d_adc
- drop casting of void *
* lm35333
- constify attribute_group structure
* lsm6dsx
- drop casting of void *
- hold ODR configuration until enabling to avoid a race condition.
* max1027
- drop casting of void *
* max11100
- fix a comma where semicolon was intended (no actual bug, just odd)
* max1363
- constify attribute_group structure
* ms sensors
- drop casting of void *
* rockchip_saradc
- drop casting of void *
* sun4i-gpadc
- fix missing dependency on THERMAL or presence of stubs (issue only
introduced in pervious set)
- drop casting of void *
* tsl2x7x
- fix wrong standard deviation calc. Note these aren't actually used for
anything at the moment so bug didn't really matter.
- constify attribute group structure.
* vf610adc
- drop casting of void *
* vz89x
- replace comma with semicolon. Not actual bug, just odd syntax.
* zpa2326
- drop casting of void *
This patch allows to avoid a transitory that occurs when a given sensor
has been already enabled (e.g. gyroscope) and the user is configuring
the sample frequency of the other one (e.g. accelerometer).
The transitory lasts until the accelerometer is enabled.
During that time slice the gyroscope ODR is incorrectly modified as well.
At the end of the transitory both sensors work at the right frequency.
Fix it introducing st_lsm6dsx_check_odr() routine to check ODR consistency
in write_raw handler in order to apply frequency configuration just
in st_lsm6dsx_set_odr()
Fixes: 290a6ce11d (iio: imu: add support to lsm6dsx driver)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When system bootup without get sensor property, set sensor
property will be fail.
If no get_feature operation done before set_feature, the sensor
properties will all be the initialized value, which is not the
same with sensor real properties. When set sensor property it will
write back to sensor the changed perperty data combines with other
sensor properties data, it is not right and may be dangerous.
In order to get all sensor properties, choose to read one of the sensor
properties(no matter read any sensor peroperty, driver will get all
the peroperties and return the requested one).
Fixes: 73c6768b71 ("iio: hid-sensors: Common attribute and trigger")
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
With CONFIG_THERMAL=m and CONFIG_SUN4I_GPADC=y, we get a link error
from calling devm_thermal_zone_of_sensor_register:
drivers/iio/built-in.o: In function `sun4i_gpadc_probe':
:(.text+0x1c284): undefined reference to `devm_thermal_zone_of_sensor_register'
This adds a Kconfig dependency to ensure we can only have the ADC
driver as built-in when this function is also built-in, or when
we see the empty stub implementation. When the thermal code is
a module, we can still build the adc driver as a module, too.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: d1caa99055 ("iio: adc: add support for Allwinner SoCs ADC")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When both accel_3d and gravity sensor are present, iio_device_register()
fails with "Duplicate scan index" error.
The reason for this is setting of indio_dev->num_channels based on
accel_3d channel for both gravity and accel-3d sensor. But number of
channels are not same, so for gravity it is pointing to some invalid
memory and getting scan_index to compare which may match.
To fix this issue, set the indio_dev->num_channels correctly based on
the sensor type.
Fixes: 0e377f3b9a ('iio: Add gravity sensor support')
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fix formatting of negative values of type IIO_VAL_FRACTIONAL_LOG2 by
switching from do_div(), which can't handle negative numbers, to
div_s64_rem(). Also use shift_right for shifting, which is safe with
negative values.
Signed-off-by: Nikolaus Schulz <nikolaus.schulz@avionic-design.de>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for the Analog Devices / Linear Technology
LTC2497 ADCs. The LTC2497 is a 16-channel (eight differential),
16-bit, high precision, delta-sigma ADC with an automatic, differential,
input current cancellation front end and a 2-wire, I2C interface.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch initializes the bootime in struct st_sensor_settings for
lps22hb sensor. Without this, sensor channels read from sysfs always
report stale values.
Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The mpu9250 is a SIP containing an mpu6500 and an ak8975. If this was all
there was too it there would be no need for explicit handling in the driver.
Arguably the bindings would also only reflect the presence of an mpu6500 with
the ak8975 hanging off it, as the kernel doesn't care that they are in one
package.
However, the WHOAMI value changes as well so best to add explicit support.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The following Coccinelle script was used to detect this:
@r@
expression x;
void* e;
type T;
identifier f;
@@
(
*((T *)e)
|
((T *)x)[...]
|
((T*)x)->f
|
- (T*)
e
)
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The following Coccinelle script was used to detect this:
@r@
expression x;
void* e;
type T;
identifier f;
@@
(
*((T *)e)
|
((T *)x)[...]
|
((T*)x)->f
|
- (T*)
e
)
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The following Coccinelle script was used to detect this:
@r@
expression x;
void* e;
type T;
identifier f;
@@
(
*((T *)e)
|
((T *)x)[...]
|
((T*)x)->f
|
- (T*)
e
)
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The following Coccinelle script was used to detect this:
@r@
expression x;
void* e;
type T;
identifier f;
@@
(
*((T *)e)
|
((T *)x)[...]
|
((T*)x)->f
|
- (T*)
e
)
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The following Coccinelle script was used to detect this:
@r@
expression x;
void* e;
type T;
identifier f;
@@
(
*((T *)e)
|
((T *)x)[...]
|
((T*)x)->f
|
- (T*)
e
)
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The following Coccinelle script was used to detect this:
@r@
expression x;
void* e;
type T;
identifier f;
@@
(
*((T *)e)
|
((T *)x)[...]
|
((T*)x)->f
|
- (T*)
e
)
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Check for attribute_group structures that are only stored in the
event_attrs filed of iio_info structure. As the event_attrs field of
iio_info structures is constant, so these attribute_group structures can
also be declared constant. Done using coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct attribute_group i@p = {...};
@ok1@
identifier r1.i;
position p;
struct iio_info x;
@@
x.event_attrs=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct attribute_group i={...};
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct attribute_group i;
As the attrs field of iio_info structures is also constant, so these
attribute_group structures can also be declared constant. Done manually.
File size before:
text data bss dec hex filename
5798 2376 0 8174 1fee drivers/iio/light/lm3533-als.o
File size after:
text data bss dec hex filename
5926 2248 0 8174 1fee drivers/iio/light/lm3533-als.o
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Aspeed BMC SoCs include a 16 channel, 10-bit ADC. Low and high threshold
interrupts are supported by the hardware but are not currently implemented.
Signed-off-by: Rick Altherr <raltherr@google.com>
Tested-by: Xo Wang <xow@google.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Check for attribute_group structures that are only stored in the
attrs filed of iio_info structure. As the attrs field of iio_info
structures is constant, so these attribute_group structures can also be
declared constant.
Done using coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct attribute_group i@p = {...};
@ok1@
identifier r1.i;
position p;
struct iio_info x;
@@
x.attrs=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct attribute_group i={...};
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct attribute_group i;
File size before:
text data bss dec hex filename
3042 480 0 3522 dc2 drivers/iio/adc/hx711.o
File size after:
text data bss dec hex filename
3098 416 0 3514 dba drivers/iio/adc/hx711.o
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Check for attribute_group structures that are only stored in the
attrs filed of iio_info structure. As the attrs field of iio_info
structures is constant, so these attribute_group structures can also be
declared constant.
Done using coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct attribute_group i@p = {...};
@ok1@
identifier r1.i;
position p;
struct iio_info x;
@@
x.attrs=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct attribute_group i={...};
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct attribute_group i;
File size before:
text data bss dec hex filename
3459 488 0 3947 f6b drivers/iio/humidity/hdc100x.o
File size after:
text data bss dec hex filename
3507 424 0 3931 f5b drivers/iio/humidity/hdc100x.o
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Check for attribute_group structures that are only stored in the
attrs filed of iio_info structure. As the attrs field of iio_info
structures is constant, so these attribute_group structures can also be
declared constant.
Done using coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct attribute_group i@p = {...};
@ok1@
identifier r1.i;
position p;
struct iio_info x;
@@
x.attrs=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct attribute_group i={...};
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct attribute_group i;
File size before:
text data bss dec hex filename
8503 488 0 8991 231f drivers/iio/light/apds9960.o
File size after:
text data bss dec hex filename
8567 424 0 8991 231f drivers/iio/light/apds9960.o
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Check for attribute_group structures that are only stored in the
attrs filed of iio_info structure. As the attrs field of iio_info
structures is constant, so these attribute_group structures can also be
declared constant.
Done using coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct attribute_group i@p = {...};
@ok1@
identifier r1.i;
position p;
struct iio_info x;
@@
x.attrs=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct attribute_group i={...};
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct attribute_group i;
File size before:
text data bss dec hex filename
2276 352 0 2628 a44 drivers/iio/light/bh1750.o
File size after:
text data bss dec hex filename
2340 320 0 2660 a64 drivers/iio/light/bh1750.o
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Check for attribute_group structures that are only stored in the
attrs filed of iio_info structure. As the attrs field of iio_info
structures is constant, so these attribute_group structures can also be
declared constant.
Done using coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct attribute_group i@p = {...};
@ok1@
identifier r1.i;
position p;
struct iio_info x;
@@
x.attrs=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct attribute_group i={...};
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct attribute_group i;
File size before:
text data bss dec hex filename
4037 288 0 4325 10e5 drivers/iio/proximity/as3935.o
File size after:
text data bss dec hex filename
4101 256 0 4357 1105 drivers/iio/proximity/as3935.o
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
On Motorola phones like droid 4 there is a custom CPCAP PMIC. This PMIC
has ADCs that are used for battery charging and USB PHY VBUS and ID pin
detection.
Unfortunately the only documentation for this ADC seems to be the
Motorola mapphone Linux kernel tree. I have tested that reading raw and
scaled values works, but I have not used the timed sampling that the ADC
seems to support.
Let's add a minimal support for it so we can eventually provide IIO
channels for the related battery charging and USB PHY drivers.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Replace a comma between expression statements by a semicolon. This
changes the semantics of the code, but given the current indentation
appears to be what is intended.
A simplified version of the Coccinelle semantic patch that performs this
transformation is as follows:
// <smpl>
@r@
expression e1,e2;
@@
e1
-,
+;
e2;
// </smpl>
Signed-off-by: Arushi Singhal <arushisinghal19971997@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Replace a comma between expression statements by a semicolon. This
changes the semantics of the code, but given the current indentation
appears to be what is intended.
A simplified version of the Coccinelle semantic patch that performs this
transformation is as follows:
// <smpl>
@r@
expression e1,e2;
@@
e1
-,
+;
e2;
// </smpl>
Signed-off-by: Arushi Singhal <arushisinghal19971997@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Check for attribute_group structures that are only stored in the
event_attrs filed of iio_info structure. As the event_attrs field of
iio_info structures is constant, so these attribute_group structures can
also be declared constant.
Done using coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct attribute_group i@p = {...};
@ok1@
identifier r1.i;
position p;
struct iio_info x;
@@
x.event_attrs=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct attribute_group i={...};
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct attribute_group i;
File size before:
text data bss dec hex filename
26051 464 0 26515 6793 drivers/iio/adc/ad799x.o
File size after:
text data bss dec hex filename
26115 400 0 26515 6793 drivers/iio/adc/ad799x.o
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Check for attribute_group structures that are only stored in the
event_attrs filed of iio_info structure. As the event_attrs field of
iio_info structures is constant, so these attribute_group structures can
also be declared constant. Done using coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct attribute_group i@p = {...};
@ok1@
identifier r1.i;
position p;
struct iio_info x;
@@
x.event_attrs=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct attribute_group i={...};
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct attribute_group i;
File size before:
text data bss dec hex filename
36951 448 0 37399 9217 drivers/iio/adc/max1363.o
File size after:
text data bss dec hex filename
37015 384 0 37399 9217 drivers/iio/adc/max1363.o
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Check for attribute_group structures that are only stored in the
event_attrs filed of iio_info structure. As the event_attrs field of
iio_info structures is constant, so these attribute_group structures can
also be declared constant. Done using coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct attribute_group i@p = {...};
@ok1@
identifier r1.i;
position p;
struct iio_info x;
@@
x.event_attrs=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct attribute_group i={...};
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct attribute_group i;
File size before:
text data bss dec hex filename
3046 360 0 3406 d4e drivers/iio/dac/ad5504.o
File size after:
text data bss dec hex filename
3110 296 0 3406 d4e drivers/iio/dac/ad5504.o
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The gyroscope chip might need to be reset to be used.
Without the chip being reset, the driver stopped at the first
regmap_read (to get the CHIP_ID) and failed to probe.
The datasheet of the gyroscope says that a minimum wait of 30ms after
the reset has to be done.
This patch has been checked on a BMX055 and the datasheet of the BMG160
and the BMI055 give the same reset register and bits.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Environmental humidity sensor is a hid defined sensor,
it shows raw humidity measurement of air.
More information can be found in:
http://www.usb.org/developers/hidpage/HUTRR39b.pdf
According to IIO ABI definition, humidityrelative data output unit is
milli percent. Add the unit convert from percent to milli percent.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Scale value include two parts: unit conversion and exponent conversion.
Add gravity unit convert table to fix gravity sensor scale value not
right issue.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for STMicro VL6180 - ALS, range and proximity sensor. Sensor is capable of measuring the light
intensity as well as object distance using TOF (Time of Flight) technology.
Signed-off-by: Manivannan Sadhasivam <manivannanece23@gmail.com>
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use resourced managed function devm_iio_triggered_buffer_setup
to make error path simpler and be able to get rid of the remove
function.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The cros_ec_sensors_read function must return the type of value on all
cases. This was always true except for RAW and CALIBBIAS data which
returned an error or 0. This patch just fixes the mistake I introduced
when submitting the series.
Fixes: commit c14dca07a3 (iio: cros_ec_sensors: add ChromeOS EC
Contiguous Sensors driver)
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds calibration for the Meson SAR ADC.
Points 25% vref and 75% vref are used for calibration.
It uses a simple linear calibration function: SCALE * val + BIAS
Successfully tested on a Odroid C2.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Since the driver has been split into MFD there is no reason for it to
stay, so remove it.
Signed-off-by: Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for sixteen-channel 12-bit resolution ADC and its functions,
which include general-purpose ADC readings, battery voltage measurement,
and die temperature measurement.
Signed-off-by: Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for Linear Technology LTC2632 (SPI) family of·
dual 12- 10-, and 8-bits output DACs.
Signed-off-by: Maxime Roussin-Belanger <maxime.roussinbelanger@gmail.com>
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Replace the open coded registration of the cdev and dev with the
new device_add_cdev() helper. The helper replaces a common pattern by
taking the proper reference against the parent device and adding both
the cdev and the device.
In doing so we have to remove a guard statement from cdev_del,
but this doesn't appear to be required in any way.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver has a OF device ID table but the struct i2c_driver
.of_match_table field is not set.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
