The DSI driver for Tegra requires the SOR power partition to be enabled.
Now that Tegra supports the generic PM domain framework we manage the
SOR power partition via this framework. However, the sequence for
gating/ungating the SOR power partition requires that the DSI reset is
asserted/de-asserted at the time the SOR power partition is
gated/ungated, respectively. Now that the reset control core assumes
that resets are exclusive, the Tegra generic PM domain code and the DSI
driver cannot request the same reset unless we mark the reset as shared.
Sharing resets will not work in this case because we cannot guarantee
that the reset will be asserted/de-asserted at the appropriate time.
Therefore, given that the Tegra generic PM domain code will handle the
resets, do not request the reset in the DSI driver if the DSI device has
a PM domain associated.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When running in HDMI mode, the sor1 IP block needs to use the sor1_src
as parent clock, and in turn configure the sor1_src to use pll_d2_out0
as its parent.
Signed-off-by: Thierry Reding <treding@nvidia.com>
sor1_brick is a clock that can be used as a source for the sor1 clock.
The registers to control the clock output are part of the sor1 IP block
and hence the sor driver is the best place to implement it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use runtime PM to clock-(un)gate and (de)assert reset to the SOR
controller. This ties in nicely with atomic DPMS in that a runtime PM
reference is taken before a pipe is enabled and dropped after it has
been shut down.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use runtime PM to clock-(un)gate and (de)assert reset to the HDMI
controller. This ties in nicely with atomic DPMS in that a runtime PM
reference is taken before a pipe is enabled and dropped after it has
been shut down.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use runtime PM to clock-(un)gate, (de)assert reset and control power to
the DSI controller. This ties in nicely with atomic DPMS in that a
runtime PM reference is taken before a pipe is enabled and dropped after
it has been shut down.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use runtime PM to clock-gate, assert reset and powergate the display
controller. This ties in nicely with atomic DPMS in that a runtime PM
reference is taken before a pipe is enabled and dropped after it has
been shut down.
To make sure this works, make sure to only ever update planes on active
CRTCs, otherwise register accesses to a clock-gated and reset CRTC will
hang the CPU.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to use the HDA codec to forward audio data to the HDMI codec it
needs the ELD that is parsed from the monitor's EDID.
Also implement an interoperability mechanism between the HDA controller
and the HDMI codec. This uses vendor-defined scratch registers to pass
data from the HDMI codec driver to the HDMI driver (that implements the
receiving end of the HDMI codec). A custom format is used to pass audio
sample rate and channel count to the HDMI driver.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Current generations of Tegra do not support deep color modes, so force
8 bits per color even if the connected monitor or panel supports more.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The code to set a video mode is common to all types of outputs that the
SOR can drive. Extract it into a separate function so that it can be
shared.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This function is useful in both eDP and DP modes, so split it out in
anticipation of adding DP support.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Switching the SOR parent clock can glitch if done while the clock is
enabled. Extract a common function that can be used to disable the
module clock, switch the parent and reenable the module clock.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DPAUX pins are shared with an internal I2C controller. To allow
these pins to be muxed to the I2C controller, register a pinctrl device
for the DPAUX device.
This is based upon work by Thierry Reding <treding@nvidia.com>.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
To utilise the DPAUX on Tegra, the SOR power partition must be enabled.
Now that Tegra supports the generic PM domain framework we manage the
SOR power partition via this framework for DPAUX. However, the sequence
for gating/ungating the SOR power partition requires that the DPAUX
reset is asserted/de-asserted at the time the SOR power partition is
gated/ungated, respectively. Now that the reset control core assumes
that resets are exclusive, the Tegra generic PM domain code and the
DPAUX driver cannot request the same reset unless we mark the resets as
shared. Sharing resets will not work in this case because we cannot
guarantee that the reset will be asserted/de-asserted at the appropriate
time. Therefore, given that the Tegra generic PM domain code will handle
the DPAUX reset, do not request the reset in the DPAUX driver if the
DPAUX device has a PM domain associated.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In preparation for adding pinctrl support for the DPAUX pads, add a
couple of helpers functions to configure the pads and control their
power.
Please note that although a simple if-statement could be used instead
of a case statement for configuring the pads as there are only two
possible modes, a case statement is used because when integrating with
the pinctrl framework, we need to be able to handle invalid modes that
could be passed.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
If the probing of the DPAUX fails, then clocks are left enabled and the
DPAUX reset de-asserted. Add code to perform the necessary clean-up on
probe failure by disabling clocks and asserting the reset.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
All outputs have a 1:1 relationship between connectors and encoders
and the driver is relying on the atomic helpers: we can drop the custom
->best_encoder() implementation and let the core call
drm_atomic_helper_best_encoder() for us.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465300095-16971-14-git-send-email-boris.brezillon@free-electrons.com
Pull drm updates from Dave Airlie:
"Here's the main drm pull request for 4.7, it's been a busy one, and
I've been a bit more distracted in real life this merge window. Lots
more ARM drivers, not sure if it'll ever end. I think I've at least
one more coming the next merge window.
But changes are all over the place, support for AMD Polaris GPUs is in
here, some missing GM108 support for nouveau (found in some Lenovos),
a bunch of MST and skylake fixes.
I've also noticed a few fixes from Arnd in my inbox, that I'll try and
get in asap, but I didn't think they should hold this up.
New drivers:
- Hisilicon kirin display driver
- Mediatek MT8173 display driver
- ARC PGU - bitstreamer on Synopsys ARC SDP boards
- Allwinner A13 initial RGB output driver
- Analogix driver for DisplayPort IP found in exynos and rockchip
DRM Core:
- UAPI headers fixes and C++ safety
- DRM connector reference counting
- DisplayID mode parsing for Dell 5K monitors
- Removal of struct_mutex from drivers
- Connector registration cleanups
- MST robustness fixes
- MAINTAINERS updates
- Lockless GEM object freeing
- Generic fbdev deferred IO support
panel:
- Support for a bunch of new panels
i915:
- VBT refactoring
- PLL computation cleanups
- DSI support for BXT
- Color manager support
- More atomic patches
- GEM improvements
- GuC fw loading fixes
- DP detection fixes
- SKL GPU hang fixes
- Lots of BXT fixes
radeon/amdgpu:
- Initial Polaris support
- GPUVM/Scheduler/Clock/Power improvements
- ASYNC pageflip support
- New mesa feature support
nouveau:
- GM108 support
- Power sensor support improvements
- GR init + ucode fixes.
- Use GPU provided topology information
vmwgfx:
- Add host messaging support
gma500:
- Some cleanups and fixes
atmel:
- Bridge support
- Async atomic commit support
fsl-dcu:
- Timing controller for LCD support
- Pixel clock polarity support
rcar-du:
- Misc fixes
exynos:
- Pipeline clock support
- Exynoss4533 SoC support
- HW trigger mode support
- export HDMI_PHY clock
- DECON5433 fixes
- Use generic prime functions
- use DMA mapping APIs
rockchip:
- Lots of little fixes
vc4:
- Render node support
- Gamma ramp support
- DPI output support
msm:
- Mostly cleanups and fixes
- Conversion to generic struct fence
etnaviv:
- Fix for prime buffer handling
- Allow hangcheck to be coalesced with other wakeups
tegra:
- Gamme table size fix"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1050 commits)
drm/edid: add displayid detailed 1 timings to the modelist. (v1.1)
drm/edid: move displayid validation to it's own function.
drm/displayid: Iterate over all DisplayID blocks
drm/edid: move displayid tiled block parsing into separate function.
drm: Nuke ->vblank_disable_allowed
drm/vmwgfx: Report vmwgfx version to vmware.log
drm/vmwgfx: Add VMWare host messaging capability
drm/vmwgfx: Kill some lockdep warnings
drm/nouveau/gr/gf100-: fix race condition in fecs/gpccs ucode
drm/nouveau/core: recognise GM108 chipsets
drm/nouveau/gr/gm107-: fix touching non-existent ppcs in attrib cb setup
drm/nouveau/gr/gk104-: share implementation of ppc exception init
drm/nouveau/gr/gk104-: move rop_active_fbps init to nonctx
drm/nouveau/bios/pll: check BIT table version before trying to parse it
drm/nouveau/bios/pll: prevent oops when limits table can't be parsed
drm/nouveau/volt/gk104: round up in gk104_volt_set
drm/nouveau/fb/gm200: setup mmu debug buffer registers at init()
drm/nouveau/fb/gk20a,gm20b: setup mmu debug buffer registers at init()
drm/nouveau/fb/gf100-: allocate mmu debug buffers
drm/nouveau/fb: allow chipset-specific actions for oneinit()
...
This was added in
commit 0a3e67a4ca
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Tue Sep 30 12:14:26 2008 -0700
drm: Rework vblank-wait handling to allow interrupt reduction.
to stay backwards-compatible with old UMS code that didn't even tell
the kernel when it did a modeset, so that the kernel could
save/restore vblank counters. At worst this means vblanks will be
somewhat funky on a setup that very likely no one still runs.
So let's just nuke it.
Plan B would be to set it unconditionally in drm_vblank_init for kms
drivers, instead of in each driver separately. So if this patch breaks
anything please only restore the hunks in drmP.h and drm_irq.c, plus
add a check for DRIVER_MODESET in drm_vblank_init.
Stumbled over this in a discussion on irc with Chris.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit d2307dea14 ("drm/atomic: use connector references (v3)") added
reference counting for DRM connectors and this caused a crash when
exercising system suspend on Tegra114 Dalmore.
The Tegra DSI driver implements a Tegra specific function,
tegra_dsi_connector_duplicate_state(), to duplicate the connector state
and destroys the state using the generic helper function,
drm_atomic_helper_connector_destroy_state(). Following commit
d2307dea14 ("drm/atomic: use connector references (v3)") there is
now an imbalance in the connector reference count because the Tegra
function to duplicate state does not take a reference when duplicating
the state information. However, the generic helper function to destroy
the state information assumes a reference has been taken and during
system suspend, when the connector state is destroyed, this leads to a
crash because we attempt to put the reference for an object that has
already been freed.
Fix this by calling __drm_atomic_helper_connector_duplicate_state() from
tegra_dsi_connector_duplicate_state() to ensure that we take a reference
on a connector if crtc is set. Note that this will also copy the
connector state a 2nd time, but this should be harmless.
By fixing tegra_dsi_connector_duplicate_state() to take a reference,
although a crash was no longer seen, it was then observed that after
each system suspend-resume cycle, the reference would be one greater
than before the suspend-resume cycle. Following commit d2307dea14
("drm/atomic: use connector references (v3)"), it was found that we
also need to put the reference when calling the function
tegra_dsi_connector_reset() before freeing the state. Fix this by
updating tegra_dsi_connector_reset() to call the function
__drm_atomic_helper_connector_destroy_state() in order to put the
reference for the connector.
Fixes: d2307dea14 ("drm/atomic: use connector references (v3)")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1463585856-16606-1-git-send-email-jonathanh@nvidia.com
It's unused, and really this helper should only look at the state
structure and nothing else.
v2: Rebase on top of rockchip changes
v3: Drop unrelated hunk, spotted by Laurent.
v4: Rebase onto mtk driver merge.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Mark Yao <mark.yao@rock-chips.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1462804451-15318-1-git-send-email-daniel.vetter@ffwll.ch
drm_gem_object_lookup() has never required the drm_device for its file
local translation of the user handle to the GEM object. Let's remove the
unused parameter and save some space.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: dri-devel@lists.freedesktop.org
Cc: Dave Airlie <airlied@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
[danvet: Fixup kerneldoc too.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I kinda hoped that I could still sneak in Noralf's
drm_simple_display_pipe, since there's intereset by others now (for tilcdc
at least). But it wasn't ready by a hair. Oh well.
Otherwise random stuff plus prep patches from Noralf.
* tag 'topic/drm-misc-2016-05-13' of git://anongit.freedesktop.org/drm-intel:
drm/atomic: Add drm_atomic_helper_best_encoder()
drm/atomic: Don't skip drm_bridge_*() calls if !drm_encoder_helper_funcs
drm/fb-cma-helper: Hook up to DocBook and fix some docs
drm/fb-helper: Remove mention of CONFIG_FB_DEFERRED_IO in docs
drm/sti: include linux/seq_file.h where needed
drm/tegra: Use lockless gem BO free callback
drm/exynos: Use lockless gem BO free callback
drm: Make drm_encoder_helper_funcs optional
Two small changes, one getting rid of the bogus gamma table size and
another removing Terje from the MAINTAINERS file since he no longer does
any work on host1x or display.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=CG36
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-4.7-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.7-rc1
Two small changes, one getting rid of the bogus gamma table size and
another removing Terje from the MAINTAINERS file since he no longer does
any work on host1x or display.
* tag 'drm/tegra/for-4.7-rc1' of git://anongit.freedesktop.org/tegra/linux:
MAINTAINERS: Remove Terje Bergström as Tegra DRM maintainer
drm/tegra: Don't set a gamma table size
Avoids drivers knowing where the kref is stored.
[airlied: add kerneldoc]
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The Tegra powergate and rail IDs are always positive values and so change
the type to be unsigned and remove the tests to see if the ID is less
than zero. Update the Tegra DC powergate type to be an unsigned as well.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra doesn't have any functions to set gamma tables, so this is
completely defunct.
Not nice to lie to userspace, so let's stop!
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 4.6 kernel.
Overall the coolest thing here for me is the nouveau maxwell signed
firmware support from NVidia, it's taken a long while to extract this
from them.
I also wish the ARM vendors just designed one set of display IP, ARM
display block proliferation is definitely increasing.
Core:
- drm_event cleanups
- Internal API cleanup making mode_fixup optional.
- Apple GMUX vga switcheroo support.
- DP AUX testing interface
Panel:
- Refactoring of DSI core for use over more transports.
New driver:
- ARM hdlcd driver
i915:
- FBC/PSR (framebuffer compression, panel self refresh) enabled by default.
- Ongoing atomic display support work
- Ongoing runtime PM work
- Pixel clock limit checks
- VBT DSI description support
- GEM fixes
- GuC firmware scheduler enhancements
amdkfd:
- Deferred probing fixes to avoid make file or link ordering.
amdgpu/radeon:
- ACP support for i2s audio support.
- Command Submission/GPU scheduler/GPUVM optimisations
- Initial GPU reset support for amdgpu
vmwgfx:
- Support for DX10 gen mipmaps
- Pageflipping and other fixes.
exynos:
- Exynos5420 SoC support for FIMD
- Exynos5422 SoC support for MIPI-DSI
nouveau:
- GM20x secure boot support - adds acceleration for Maxwell GPUs.
- GM200 support
- GM20B clock driver support
- Power sensors work
etnaviv:
- Correctness fixes for GPU cache flushing
- Better support for i.MX6 systems.
imx-drm:
- VBlank IRQ support
- Fence support
- OF endpoint support
msm:
- HDMI support for 8996 (snapdragon 820)
- Adreno 430 support
- Timestamp queries support
virtio-gpu:
- Fixes for Android support.
rockchip:
- Add support for Innosilicion HDMI
rcar-du:
- Support for 4 crtcs
- R8A7795 support
- RCar Gen 3 support
omapdrm:
- HDMI interlace output support
- dma-buf import support
- Refactoring to remove a lot of legacy code.
tilcdc:
- Rewrite of pageflipping code
- dma-buf support
- pinctrl support
vc4:
- HDMI modesetting bug fixes
- Significant 3D performance improvement.
fsl-dcu (FreeScale):
- Lots of fixes
tegra:
- Two small fixes
sti:
- Atomic support for planes
- Improved HDMI support"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1063 commits)
drm/amdgpu: release_pages requires linux/pagemap.h
drm/sti: restore mode_fixup callback
drm/amdgpu/gfx7: add MTYPE definition
drm/amdgpu: removing BO_VAs shouldn't be interruptible
drm/amd/powerplay: show uvd/vce power gate enablement for tonga.
drm/amd/powerplay: show uvd/vce power gate info for fiji
drm/amdgpu: use sched fence if possible
drm/amdgpu: move ib.fence to job.fence
drm/amdgpu: give a fence param to ib_free
drm/amdgpu: include the right version of gmc header files for iceland
drm/radeon: fix indentation.
drm/amd/powerplay: add uvd/vce dpm enabling flag to fix the performance issue for CZ
drm/amdgpu: switch back to 32bit hw fences v2
drm/amdgpu: remove amdgpu_fence_is_signaled
drm/amdgpu: drop the extra fence range check v2
drm/amdgpu: signal fences directly in amdgpu_fence_process
drm/amdgpu: cleanup amdgpu_fence_wait_empty v2
drm/amdgpu: keep all fences in an RCU protected array v2
drm/amdgpu: add number of hardware submissions to amdgpu_fence_driver_init_ring
drm/amdgpu: RCU protected amd_sched_fence_release
...
Rename dma_*_writecombine() to dma_*_wc(), so that the naming
is coherent across the various write-combining APIs. Keep the
old names for compatibility for a while, these can be removed
at a later time. A guard is left to enable backporting of the
rename, and later remove of the old mapping defines seemlessly.
Build tested successfully with allmodconfig.
The following Coccinelle SmPL patch was used for this simple
transformation:
@ rename_dma_alloc_writecombine @
expression dev, size, dma_addr, gfp;
@@
-dma_alloc_writecombine(dev, size, dma_addr, gfp)
+dma_alloc_wc(dev, size, dma_addr, gfp)
@ rename_dma_free_writecombine @
expression dev, size, cpu_addr, dma_addr;
@@
-dma_free_writecombine(dev, size, cpu_addr, dma_addr)
+dma_free_wc(dev, size, cpu_addr, dma_addr)
@ rename_dma_mmap_writecombine @
expression dev, vma, cpu_addr, dma_addr, size;
@@
-dma_mmap_writecombine(dev, vma, cpu_addr, dma_addr, size)
+dma_mmap_wc(dev, vma, cpu_addr, dma_addr, size)
We also keep the old names as compatibility helpers, and
guard against their definition to make backporting easier.
Generated-by: Coccinelle SmPL
Suggested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: airlied@linux.ie
Cc: akpm@linux-foundation.org
Cc: benh@kernel.crashing.org
Cc: bhelgaas@google.com
Cc: bp@suse.de
Cc: dan.j.williams@intel.com
Cc: daniel.vetter@ffwll.ch
Cc: dhowells@redhat.com
Cc: julia.lawall@lip6.fr
Cc: konrad.wilk@oracle.com
Cc: linux-fbdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: luto@amacapital.net
Cc: mst@redhat.com
Cc: tomi.valkeinen@ti.com
Cc: toshi.kani@hp.com
Cc: vinod.koul@intel.com
Cc: xen-devel@lists.xensource.com
Link: http://lkml.kernel.org/r/1453516462-4844-1-git-send-email-mcgrof@do-not-panic.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The core takes care of that now.
v2: Fixup misplaced hunk.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Terje Bergström <tbergstrom@nvidia.com>
Acked-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453756616-28942-12-git-send-email-daniel.vetter@ffwll.ch
Since your main drm-next pull isn't out of the door yet I figured I might
as well flush out drm-misc instead of delaying for 4.6. It's really just
random stuff all over, biggest thing probably connector_mask tracking from
Maarten.
* tag 'topic/drm-misc-2016-01-17' of git://anongit.freedesktop.org/drm-intel: (24 commits)
drm/fb_cma_helper: Remove implicit call to disable_unused_functions
drm/sysfs: use kobj_to_dev()
drm/i915: Init power domains early in driver load
drm: Do not set connector->encoder in drivers
apple-gmux: Add initial documentation
drm: move MODULE_PARM_DESC to other file
drm/edid: index CEA/HDMI mode tables using the VIC
drm/atomic: Remove drm_atomic_connectors_for_crtc.
drm/i915: Update connector_mask during readout, v2.
drm: Remove opencoded drm_gem_object_release_handle()
drm: Do not set outparam on error during GEM handle allocation
drm/docs: more leftovers from the big vtable documentation pile
drm/atomic-helper: Reject legacy flips on a disabled pipe
drm/atomic: add connector mask to drm_crtc_state.
drm/tegra: Use __drm_atomic_helper_reset_connector for subclassing connector state, v2.
drm/atomic: Add __drm_atomic_helper_connector_reset, v2.
drm/i915: Set connector_state->connector using the helper.
drm: Use a normal idr allocation for the obj->name
drm: Only bump object-reference count when adding first handle
drm: Balance error path for GEM handle allocation
...
Seems I lied in my last drm-misc pull request and suddenly there's a big
pile of random stuff. Boris dug out Thierry's drm-trivial branch and
resubmitted everything since that branch didn't really work out.
On top of that Nicolas' changes to drm_dev_set_unique - this might
conflict with new driver pulls (I double checked and current drm-next
should be fine), so please beware. The -next/-fixes conflict in vmwgfx
will change slightly with this here too.
* tag 'topic/drm-misc-2015-12-18' of git://anongit.freedesktop.org/drm-intel: (36 commits)
drm: use dev_name as default unique name in drm_dev_alloc()
drm: make drm_dev_set_unique() not use a format string
drm/vmwgfx: Constify function pointer structs
drm/udl: Constify function pointer structs
drm/tegra: Constify function pointer structs
drm/rockchip: Constify function pointer structs
drm/nouveau: Constify function pointer structs
drm/mgag200: Constify function pointer structs
drm/imx: Constify function pointer structs
drm/i2c/sil164: Constify function pointer structs
drm/i2c/adv7511: Constify function pointer structs
drm/exynos: Constify function pointer structs
drm/cirrus: Constify function pointer structs
drm/i2c/ch7006: Constify function pointer structs
drm/bridge/nxp-ptn3460: Constify function pointer structs
drm/bridge/dw_hdmi: Constify function pointer structs
drm/bochs: Constify function pointer structs
drm/atmel-hlcdc: Constify function pointer structs
drm/armada: Constify function pointer structs
drm: Constify drm_encoder_slave_funcs
...
This adds support for the version of host1x found on Tegra210 SoCs. It
also makes use of the new atomic suspend/resume functionality to bring
this feature to Tegra.
Other than that it's mostly small fixes and cleanups, with some prep-
work for things that will hopefully get merged for the next release.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=aaka
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-4.5-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.5-rc1
This adds support for the version of host1x found on Tegra210 SoCs. It
also makes use of the new atomic suspend/resume functionality to bring
this feature to Tegra.
Other than that it's mostly small fixes and cleanups, with some prep-
work for things that will hopefully get merged for the next release.
* tag 'drm/tegra/for-4.5-rc1' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: Advertise DRIVER_ATOMIC
drm/tegra: Use DRIVER level for IOMMU aperture message
drm/tegra: checking for IS_ERR() instead of NULL
drm/tegra: dc: Add missing of_node_put()
drm/tegra: Implement subsystem-level suspend/resume
drm/tegra: sor: Remove unnecessary conditional
drm/tegra: sor: Operate on struct drm_dp_aux *
drm/tegra: Use drm_gem_object_unreference_unlocked()
drm/tegra: Don't take dev->struct_mutex in mmap offset ioctl
drm/tegra: Use unlocked gem unreferencing
drm/tegra: Use new multi-driver module helpers
gpu: host1x: Add Tegra210 support
gpu: host1x: Remove core driver on unregister
gpu: host1x: Use platform_register/unregister_drivers()
The following code pattern exists in some DRM drivers:
ddev = drm_dev_alloc(&driver, parent_dev);
drm_dev_set_unique(ddev, dev_name(parent_dev));
(Sometimes dev_name(ddev->dev) is used, which is the same.)
As suggested in
http://lists.freedesktop.org/archives/dri-devel/2015-December/096441.html,
the unique name of a new DRM device can be set as dev_name(parent_dev)
when parent_dev is not NULL (vgem is a special case).
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Moves a bunch of junk to .rodata from .data.
drivers/gpu/drm/tegra/tegra-drm.ko:
-.rodata 13672
+.rodata 13684
-.data 1108
+.data 1096
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-26-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The tegra_sor_hdmi_find_settings() function returns NULL on error and
not an ERR_PTR.
Fixes: 459cc2c680 ('drm/tegra: sor: Add HDMI support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
for_each_matching_node() performs an of_node_get() on each iteration, so
a break out of the loop requires an of_node_put().
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
local idexpression n;
expression e;
@@
for_each_matching_node(n,...) {
...
(
of_node_put(n);
|
e = n
|
+ of_node_put(n);
? break;
)
...
}
... when != n
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use the drm_atomic_helper_suspend() and drm_atomic_helper_resume()
helpers to implement subsystem-level suspend/resume.
v2: suspend framebuffer device to avoid concurrency issues
v3: resume fbdev on failure to suspend (Emil Velikov)
Signed-off-by: Thierry Reding <treding@nvidia.com>
Checking for sor->aux in eDP specific code is unnecessary because eDP
inherently requires a valid AUX channel.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Instead of getting a pointer to the driver-specific wrapper of AUX
channels, use the AUX channel objects directly to avoid hackish casting
between the two types.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This only grabs the mutex when really needed, but still has a might-
acquire lockdep check to make sure that's always possible. With this
patch Tegra DRM is officially struct_mutex free, yay!
v2: refernce_unlocked doesn't exist as kbuild spotted.
Cc: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
[treding@nvidia.com: remove unused variables]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Since David Herrmann's mmap vma manager rework we don't need to grab
dev->struct_mutex any more to prevent races when looking up the mmap
offset. Drop it and instead don't forget to use the unref_unlocked
variant (since the drm core still cares).
v2: Finally get rid of the copypasta from another commit in this
commit message. And convert to _unlocked like we need to (Patrik).
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
For drm_gem_object_unreference callers are required to hold
dev->struct_mutex, which these paths don't. Enforcing this requirement
has become a bit more strict with
commit ef4c6270bf
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Oct 15 09:36:25 2015 +0200
drm/gem: Check locking in drm_gem_object_unreference
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use the new multi-driver module helpers to get rid of some boilerplate
in the module initialization and cleanup functions.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Done with coccinelle for the most part. However, it thinks '...' is
part of the semantic patch, so I put an 'int DOTDOTDOT' placeholder
in its place and got rid of it with sed afterwards.
@@
identifier dev, encoder, funcs;
@@
int drm_encoder_init(struct drm_device *dev,
struct drm_encoder *encoder,
const struct drm_encoder_funcs *funcs,
int encoder_type
+ ,const char *name, int DOTDOTDOT
)
{ ... }
@@
identifier dev, encoder, funcs;
@@
int drm_encoder_init(struct drm_device *dev,
struct drm_encoder *encoder,
const struct drm_encoder_funcs *funcs,
int encoder_type
+ ,const char *name, int DOTDOTDOT
);
@@
expression E1, E2, E3, E4;
@@
drm_encoder_init(E1, E2, E3, E4
+ ,NULL
)
v2: Add ', or NULL...' to @name kernel doc (Jani)
Annotate the function with __printf() attribute (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449670818-2966-1-git-send-email-ville.syrjala@linux.intel.com
Done with coccinelle for the most part. It choked on
msm/mdp/mdp5/mdp5_plane.c like so:
"BAD:!!!!! enum drm_plane_type type;"
No idea how to deal with that, so I just fixed that up
by hand.
Also it thinks '...' is part of the semantic patch, so I put an
'int DOTDOTDOT' placeholder in its place and got rid of it with
sed afterwards.
I didn't convert drm_plane_init() since passing the varargs through
would mean either cpp macros or va_list, and I figured we don't
care about these legacy functions enough to warrant the extra pain.
@@
typedef uint32_t;
identifier dev, plane, possible_crtcs, funcs, formats, format_count, type;
@@
int drm_universal_plane_init(struct drm_device *dev,
struct drm_plane *plane,
unsigned long possible_crtcs,
const struct drm_plane_funcs *funcs,
const uint32_t *formats,
unsigned int format_count,
enum drm_plane_type type
+ ,const char *name, int DOTDOTDOT
)
{ ... }
@@
identifier dev, plane, possible_crtcs, funcs, formats, format_count, type;
@@
int drm_universal_plane_init(struct drm_device *dev,
struct drm_plane *plane,
unsigned long possible_crtcs,
const struct drm_plane_funcs *funcs,
const uint32_t *formats,
unsigned int format_count,
enum drm_plane_type type
+ ,const char *name, int DOTDOTDOT
);
@@
expression E1, E2, E3, E4, E5, E6, E7;
@@
drm_universal_plane_init(E1, E2, E3, E4, E5, E6, E7
+ ,NULL
)
v2: Split crtc and plane changes apart
Pass NUL for no-name instead of ""
Leave drm_plane_init() alone
v3: Add ', or NULL...' to @name kernel doc (Jani)
Annotate the function with __printf() attribute (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449670795-2853-1-git-send-email-ville.syrjala@linux.intel.com
Done with coccinelle for the most part. However, it thinks '...' is
part of the semantic patch, so I put an 'int DOTDOTDOT' placeholder
in its place and got rid of it with sed afterwards.
I didn't convert drm_crtc_init() since passing the varargs through
would mean either cpp macros or va_list, and I figured we don't
care about these legacy functions enough to warrant the extra pain.
@@
identifier dev, crtc, primary, cursor, funcs;
@@
int drm_crtc_init_with_planes(struct drm_device *dev,
struct drm_crtc *crtc,
struct drm_plane *primary, struct drm_plane *cursor,
const struct drm_crtc_funcs *funcs
+ ,const char *name, int DOTDOTDOT
)
{ ... }
@@
identifier dev, crtc, primary, cursor, funcs;
@@
int drm_crtc_init_with_planes(struct drm_device *dev,
struct drm_crtc *crtc,
struct drm_plane *primary, struct drm_plane *cursor,
const struct drm_crtc_funcs *funcs
+ ,const char *name, int DOTDOTDOT
);
@@
expression E1, E2, E3, E4, E5;
@@
drm_crtc_init_with_planes(E1, E2, E3, E4, E5
+ ,NULL
)
v2: Split crtc and plane changes apart
Pass NULL for no-name instead of ""
Leave drm_crtc_init() alone
v3: Add ', or NULL...' to @name kernel doc (Jani)
Annotate the function with __printf() attribute (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449670771-2751-1-git-send-email-ville.syrjala@linux.intel.com
Drivers shouldn't clobber the passed in addfb ioctl parameters.
i915 was doing just that. To prevent it from happening again,
pass the struct around as const, starting all the way from
internal_framebuffer_create().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DRM_TEGRA_FBDEV config is currently used to enable/disable legacy fbdev
emulation for the tegra kms driver.
Remove this local config option and use the top level DRM_FBDEV_EMULATION
config option instead.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1445933459-5249-4-git-send-email-architt@codeaurora.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm updates from Dave Airlie:
"I Was Almost Tempted To Capitalise Every Word, but then I decided I
couldn't read it myself!
I've also got one pull request for the sti driver outstanding. It
relied on a commit in Greg's tree and I didn't find out in time, that
commit is in your tree now so I might send that along once this is
merged.
I also had the accidental misfortune to have access to a Skylake on my
desk for a few days, and I've had to encourage Intel to try harder,
which seems to be happening now.
Here is the main drm-next pull request for 4.4.
Highlights:
New driver:
vc4 driver for the Rasberry Pi VPU.
(From Eric Anholt at Broadcom.)
Core:
Atomic fbdev support
Atomic helpers for runtime pm
dp/aux i2c STATUS_UPDATE handling
struct_mutex usage cleanups.
Generic of probing support.
Documentation:
Kerneldoc for VGA switcheroo code.
Rename to gpu instead of drm to reflect scope.
i915:
Skylake GuC firmware fixes
HPD A support
VBT backlight fallbacks
Fastboot by default for some systems
FBC work
BXT/SKL workarounds
Skylake deeper sleep state fixes
amdgpu:
Enable GPU scheduler by default
New atombios opcodes
GPUVM debugging options
Stoney support.
Fencing cleanups.
radeon:
More efficient CS checking
nouveau:
gk20a instance memory handling improvements.
Improved PGOB detection and GK107 support
Kepler GDDR5 PLL statbility improvement
G8x/GT2xx reclock improvements
new userspace API compatiblity fixes.
virtio-gpu:
Add 3D support - qemu 2.5 has it merged for it's gtk backend.
msm:
Initial msm88896 (snapdragon 8200)
exynos:
HDMI cleanups
Enable mixer driver byt default
Add DECON-TV support
vmwgfx:
Move to using memremap + fixes.
rcar-du:
Add support for R8A7793/4 DU
armada:
Remove support for non-component mode
Improved plane handling
Power savings while in DPMS off.
tda998x:
Remove unused slave encoder support
Use more HDMI helpers
Fix EDID read handling
dwhdmi:
Interlace video mode support for ipu-v3/dw_hdmi
Hotplug state fixes
Audio driver integration
imx:
More color formats support.
tegra:
Minor fixes/improvements"
[ Merge fixup: remove unused variable 'dev' that had all uses removed in
commit 4e270f0880: "drm/gem: Drop struct_mutex requirement from
drm_gem_mmap_obj" ]
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (764 commits)
drm/vmwgfx: Relax irq locking somewhat
drm/vmwgfx: Properly flush cursor updates and page-flips
drm/i915/skl: disable display side power well support for now
drm/i915: Extend DSL readout fix to BDW and SKL.
drm/i915: Do graphics device reset under forcewake
drm/i915: Skip fence installation for objects with rotated views (v4)
vga_switcheroo: Drop client power state VGA_SWITCHEROO_INIT
drm/amdgpu: group together common fence implementation
drm/amdgpu: remove AMDGPU_FENCE_OWNER_MOVE
drm/amdgpu: remove now unused fence functions
drm/amdgpu: fix fence fallback check
drm/amdgpu: fix stoping the scheduler timeout
drm/amdgpu: cleanup on error in amdgpu_cs_ioctl()
drm/i915: Fix locking around GuC firmware load
drm/amdgpu: update Fiji's Golden setting
drm/amdgpu: update Fiji's rev id
drm/amdgpu: extract common code in vi_common_early_init
drm/amd/scheduler: don't oops on failure to load
drm/amdgpu: don't oops on failure to load (v2)
drm/amdgpu: don't VT switch on suspend
...
Switch everything to the new and more capable implementation of abs().
Mainly to give the new abs() a bit of a workout.
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Just a couple of minor fixes and cleanups for this cycle.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=c0/4
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-4.4-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.4-rc1
Just a couple of minor fixes and cleanups for this cycle.
* tag 'drm/tegra/for-4.4-rc1' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: dc: Request/free syncpoint at init/exit
drm/tegra: fb: Remove gratuituous blank line
gpu: host1x: Fix MLOCK's debug info
syncpoints are resources provided by host1x and their lifetime is tied
to the host1x device. They are not properly reference counted either, so
removing the host1x device before any of its clients causes a use-after-
free error. Adding proper reference counting would be a major enterprise
so work around it for now by requesting and freeing the syncpoint at
init and exit time, respectively. The host1x device is guaranteed to be
around at this point.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This was introduced by mistake in commit 0f7d9052fb ("drm/tegra: Use
new drm_fb_helper functions"). Remove it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Just one special case (since i915 lost its ums code, yay):
- radeon: Has slots for the old ums ioctls which don't have
DRM_UNLOCKED, but all filled with drm_invalid_op. So ok to drop it
everywhere.
Every other kms driver just has DRM_UNLOCKED for all their ioctls, as
they should.
v2: admgpu happened, include that one too. And i915 lost its UMS
support which means we can change all the i915 ioctls too.
v3: Rebased on top of new vmwgfx DX interface extensions.
v4: Rebase on top of render-node support in exynos.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This continues the pattern started in commit cc1ef118fc ("drm/irq:
Make pipe unsigned and name consistent"). This is applied to the public
APIs and driver callbacks, so pretty much all drivers need to be updated
to match the new prototypes.
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Jianwei Wang <jianwei.wang.chn@gmail.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A address-only I2C_WRITE can't be replied with a short i2c ack, but I
suppose it could be replied with an i2c defer. So the code should be
prepared for an address-only I2C_WRITE_STATUS_UPDATE.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: "Terje Bergström" <tbergstrom@nvidia.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rename the I2C_STATUS request to I2C_WRITE_STATUS_UPDATE to match the
spec.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
With drivers supporting runtime pm it's generally not a good idea to
touch the hardware when it's off. Add an option to the commit_planes
helper to support this case.
Note that the helpers already add all planes on a crtc when a modeset
happens, hence plane updates will not be lost if drivers set this to
true.
v2: Check for NULL state->crtc before chasing the pointer. Also check
both old and new crtc if there's a switch. Finally just outright
disallow switching crtcs for a plane if the plane is in active use, on
most hardware that doesn't make sense.
v3: Since commit_planes(active_only = true) is for enabling things
only after all the crtc are on we should only look at the new crtc to
decide whether to call the plane hooks - if the current CRTC isn't on
then skip. If the old crtc (when moving a plane) went down then the
plane should have been disabled as part of the pipe shutdown work
already. For which there's currently no helper really unfortunately.
Also move the check for wether a plane gets a new CRTC assigned while
still in active use out of this patch.
v4: Rebase over exynos changes.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
This removes the need to separately track fb changes i915.
That will be done as a separate commit, however.
Changes since v1:
- Add dri-devel to cc.
- Fix a check in intel's prepare and cleanup fb to take rotation
into account.
Changes since v2:
- Split out i915 changes to a separate commit.
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
[danvet: Squash in msm fixup from Maarten.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are a bunch of non-critical fixes here that I've collected over
the past few months, but the biggest part is Tegra210 support, in the
DC, DSI and SOR/HDMI drivers.
Also this finally restores DPMS with atomic mode-setting, something
that has been broken since the conversion and which I had originally
expected to take far less longer to fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJVzgFhAAoJEN0jrNd/PrOhBLAP/2vDyK8H52ZusDdh06GNnmSB
hr3Dfa3tePWUH/Um5qSPUvzdJg8Pnz85LsYUuQuHQRLeXfk2IsDe284CpMcKt6pW
YQPXYqQreKwZFgct2fjqohlqRjNP6qRWuPYsTciz0IMiSFyEJY9DBuYhQQbD+HHb
9CJsHNUl2Oi3jOORvuawJKIyDPFfh4JzPRGcfdGRSE1VE6qt5Cb6XVcQxwR6R6UW
7NlOg0ylYcSkC1PpDTSIpTdpksxNJI0I4k263UlYQ9sfmHQjX1N3Ef/s1DOm4vHf
1CWJlT0zI8BVerukMe2rDkyzsXJgVN5QphQzwnRz7AhEtXtFNUKoRP6mIsCjYxRp
3HTQI4rOF2VbHw2yDSOTl9SBrq94dOtkZ3YskvHQICjcO6P/602ZqFrLjFj/jn6n
rMNXoioYi8u3DDGsCdutiQTh+7BiQx9Mk/vVOei0vEeUk5KefGSawMwjo1Djjknb
aagRpVHAbTZV178RO8tMGB10Z2aiYdYp/K7sywK4ktkhlYUGpIH6kmPwY/bERPes
dZMqABSG8AslKZYrZhXWcXBPq5ymGojcJ0mqD7rK8xk1hAsE1LbMHqVwfrMCOaue
r4bnhjnBkjcSXa+Pwz/5OvdbmLjXxmWMGIes1DYYgsWaIBvPfTMCzMv7Cq6f6A9X
7zCHroPgA/APxrk3b4Dc
=lxYn
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-4.3-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.3-rc1
There are a bunch of non-critical fixes here that I've collected over
the past few months, but the biggest part is Tegra210 support, in the
DC, DSI and SOR/HDMI drivers.
Also this finally restores DPMS with atomic mode-setting, something
that has been broken since the conversion and which I had originally
expected to take far less longer to fix.
* tag 'drm/tegra/for-4.3-rc1' of git://anongit.freedesktop.org/tegra/linux: (41 commits)
drm/tegra: sor: Add HDMI support
drm/tegra: sor: Add Tegra210 eDP support
drm/tegra: dc: Implement atomic DPMS
drm/tegra: sor: Restore DPMS
drm/tegra: dsi: Restore DPMS
drm/tegra: hdmi: Restore DPMS
drm/tegra: rgb: Restore DPMS
drm/tegra: sor: Use DRM debugfs infrastructure for CRC
drm/tegra: sor: Write correct head state registers
drm/tegra: sor: Constify display mode
drm/tegra: sor: Reset the correct debugfs fields
drm/tegra: sor: Set minor after debugfs initialization
drm/tegra: sor: Provide error messages in probe
drm/tegra: sor: Rename registers for consistency
drm/tegra: dpaux: Disable interrupt when detached
drm/tegra: dpaux: Configure pads as I2C by default
drm/tegra: dpaux: Provide error message in probe
drm/tegra: dsi: Add Tegra210 support
drm/tegra: dsi: Add Tegra132 support
drm/tegra: dsi: Add Tegra124 support
...
The SOR1 introduced on Tegra210 supports HDMI 2.0 and DisplayPort. Add
HDMI support and name the debugfs node after the type of SOR. The SOR
introduced with Tegra124 is known simply as "sor", whereas the
additional SOR found on Tegra210 is known as "sor1".
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SOR found on Tegra210 is very similar to the version found on
Tegra124, except that it no longer supports LVDS.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Move all code into the new canonical ->disable() and ->enable() helper
callbacks so that they play extra nice with atomic DPMS.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to restore DPMS with atomic mode-setting, move all code from
the ->mode_set() callback into ->enable(). At the same time, rename the
->prepare() callback to ->disable() to use the names preferred by atomic
mode-setting. This simplifies the calling sequence and will allow DPMS
to use runtime PM in subsequent patches.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to restore DPMS with atomic mode-setting, move all code from
the ->mode_set() callback into ->enable(). At the same time, rename the
->prepare() callback to ->disable() to use the names preferred by atomic
mode-setting. This simplifies the calling sequence and will allow DPMS
to use runtime PM in subsequent patches.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to restore DPMS with atomic mode-setting, move all code from
the ->mode_set() callback into ->enable(). At the same time, rename the
->prepare() callback to ->disable() to use the names preferred by atomic
mode-setting. This simplifies the calling sequence and will allow DPMS
code to use runtime PM in subsequent patches.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to restore DPMS with atomic mode-setting, move all code from
the ->mode_set() callback into ->enable(). At the same time, rename the
->prepare() callback to ->disable() to use the names preferred by atomic
mode-setting. This simplifies the calling sequence and will allow DPMS
code to use runtime PM in subsequent patches.
While at it, remove the enabled field that hasn't been used since the
demidlayering of the output drivers done in preparation for the atomic
mode-setting conversion.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Instead of duplicating most of the code to set up a debugfs file, use
the existing DRM core debugfs infrastructure instead.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The head state registers are per head, so they must be properly indexed.
This has worked fine so far because all boards with eDP use it as the
primary output, so it is very likely to end up attached to head 0.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The data structure is always only read, never written, and can hence be
referred to by a const pointer.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When tearing down debugfs support, make sure to reset the fields to NULL
in the correct order, otherwise the debugfs root will not be properly
removed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DRM minor is needed to teardown debugfs, so it needs to be tracked
to prevent a crash on driver removal.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When probing the SOR device fails, output proper error messages to help
diagnose the cause of the failure.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The TRM lists indexed registers without an underscore to separate name
from index. Use that convention in the driver for consistency.
While at it, rename some of the field names to the names used in the
TRM.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When the DPAUX isn't attached to an SOR the interrupts are not useful.
This also prevents a race that could potentially cause a crash on driver
removal.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DPAUX code paths already configure the pads in AUX mode, but there
is no way to reconfigure them in I2C mode for HDMI (the DPAUX module is
unused in that case). Enabling the pads in I2C mode by default is the
quickest way to support HDMI. Eventually this may need an explicit call
in the user drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When probing the dpaux device fails, output proper error messages to
help diagnose the cause of the failure.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DSI host controller hasn't changed from Tegra132 to Tegra210, but
different characterization parameters may be required.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DSI host controller hasn't changed from Tegra124 to Tegra132, but
different characterization parameters may be required.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DSI host controller hasn't changed from Tegra114 to Tegra124, but
different characterization parameters may be required.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In video modes without sync pulses, the horizontal back-porch needs to
include the horizontal sync width.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The call to platform_driver_register() will already set up the .owner
field, so there's no need to do it explicitly.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The horizontal pulse enable bits are named H_PULSE{0,1,2}_ENABLE in the
TRM. Modify the driver to use the same naming for consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Record interrupt statistics, such as the number of frames and VBLANKs
received and the number of FIFO underflow and overflows.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Request a syncpoint for display prior to registering the host1x client.
This will ensure that the syncpoint will be acquired when the KMS driver
initializes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Upon driver load, reset the VBLANK machinery to off to reflect the
hardware state. Since the ->reset() callback is called from the initial
drm_mode_config_reset() call, move the latter after the VBLANK machinery
initialization by drm_vblank_init().
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use the newly created wrapper drm_fb_helper functions instead of calling
core fbdev functions directly. They also simplify the fb_info creation.
v2:
- Fix up error handling path in tegra_fbdev_probe
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: "Terje Bergström" <tbergstrom@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is required to properly handle failing dpms calls.
When making a wait in i915 interruptible, I've noticed
that the dpms sequence could fail with -ERESTARTSYS because
it was waiting interruptibly for flips. So from now on
allow drivers to fail in their connector dpms callback.
Encoder and crtc dpms callbacks are unaffected.
Changes since v1:
- Update kerneldoc for the drm helper functions.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
[danvet: Resolve conflicts due to different merge order.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In intel it's useful to keep track of some state changes with old
crtc state vs new state, for example to disable initial planes or
when a modeset's prevented during fastboot.
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
[danvet: squash in fixup for exynos provided by Maarten.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This contains a couple of mostly fixes for issues that have crept up in
recent versions of linux-next. One issue is that DP AUX transactions of
more than 4 bytes will access the wrong FIFO registers and hence become
corrupt. Another fix is required to restore functionality of Tegra20 if
using the GART. The current code expects the IOMMU aperture to be the
complete 4 GiB address space, whereas the GART on Tegra20 only provides
a 128 MiB aperture. One more issue with IOMMU support is that on 64-bit
ARM, swiotlb is the default IOMMU implementation backing the DMA API. A
side-effect of that is that when dma_map_sg() is called to flush caches
(yes, this is a bit of a hack, but ARM does not provide a better API),
swiotlb will immediately run out of memory because its bounce buffer is
too small to make a framebuffer.
Finally I've included a mostly cosmetic fix that stores register values
in u32 rather than unsigned long to avoid sign-extension issues on 64-
bit ARM. This is only a precaution since it hasn't caused any issues
(yet).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=3vlA
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-4.2-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.2-rc1
This contains a couple of mostly fixes for issues that have crept up in
recent versions of linux-next. One issue is that DP AUX transactions of
more than 4 bytes will access the wrong FIFO registers and hence become
corrupt. Another fix is required to restore functionality of Tegra20 if
using the GART. The current code expects the IOMMU aperture to be the
complete 4 GiB address space, whereas the GART on Tegra20 only provides
a 128 MiB aperture. One more issue with IOMMU support is that on 64-bit
ARM, swiotlb is the default IOMMU implementation backing the DMA API. A
side-effect of that is that when dma_map_sg() is called to flush caches
(yes, this is a bit of a hack, but ARM does not provide a better API),
swiotlb will immediately run out of memory because its bounce buffer is
too small to make a framebuffer.
Finally I've included a mostly cosmetic fix that stores register values
in u32 rather than unsigned long to avoid sign-extension issues on 64-
bit ARM. This is only a precaution since it hasn't caused any issues
(yet).
* tag 'drm/tegra/for-4.2-rc1' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: dpaux: Registers are 32-bit
drm/tegra: gem: Flush pages after allocation
drm/tegra: gem: Take into account IOMMU aperture
drm/tegra: dpaux: Fix transfers larger than 4 bytes
Use a sized unsigned 32-bit data type (u32) to store register contents.
The DPAUX registers are 32 bits wide irrespective of the architecture's
data width.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Pages allocated from shmemfs don't end up being cleared and flushed on
ARMv7, so they must be flushed explicitly. Use the DMA mapping API for
that purpose, even though it's not used for anything else.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The IOMMU may not always be able to address 2 GiB of memory. On Tegra20,
the GART supports 32 MiB starting at 0x58000000. Also the aperture on
Tegra30 and later is in fact the full 4 GiB, rather than just 2 GiB as
currently assumed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DPAUX read/write FIFO registers aren't sequential in the register
space, causing transfers larger than 4 bytes to cause accesses to non-
existing FIFO registers.
Fixes: 6b6b604215 ("drm/tegra: Add eDP support")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra would not only need a hardware vblank counter that
increments at leading edge of vblank, but also support
for instantaneous high precision vblank timestamp queries, ie.
a proper implementation of dev->driver->get_vblank_timestamp().
Without these, there can be off-by-one errors during vblank
disable/enable if the scanout is inside vblank at en/disable
time, and additionally clients will never see any useable
vblank timestamps when querying via drmWaitVblank ioctl. This
would negatively affect swap scheduling under X11 and Wayland.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
At present, dma_buf_export() takes a series of parameters, which
makes it difficult to add any new parameters for exporters, if required.
Make it simpler by moving all these parameters into a struct, and pass
the struct * as parameter to dma_buf_export().
While at it, unite dma_buf_export_named() with dma_buf_export(), and
change all callers accordingly.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Perhaps the most noteworthy change in this set is the implementation of
a hardware VBLANK counter using host1x syncpoints. The SOR registers can
now be dumped via debugfs, which can be useful while debugging. The IOVA
address space maintained by the driver can also be dumped via debugfs.
Other than than, these changes are mostly cleanup work, such as making
register names more consistent or removing unused code (that was left
over after the atomic mode-setting conversion). There's also a fix for
eDP that makes the driver cope with firmware that already initialized
the display (such as the firmware on the Tegra-based Chromebooks).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=HZO1
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-4.1-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.1-rc1
Perhaps the most noteworthy change in this set is the implementation of
a hardware VBLANK counter using host1x syncpoints. The SOR registers can
now be dumped via debugfs, which can be useful while debugging. The IOVA
address space maintained by the driver can also be dumped via debugfs.
Other than than, these changes are mostly cleanup work, such as making
register names more consistent or removing unused code (that was left
over after the atomic mode-setting conversion). There's also a fix for
eDP that makes the driver cope with firmware that already initialized
the display (such as the firmware on the Tegra-based Chromebooks).
* tag 'drm/tegra/for-4.1-rc1' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: sor: Reset during initialization
drm/tegra: gem: Return 64-bit offset for mmap(2)
drm/tegra: hdmi: Name register fields consistently
drm/tegra: hdmi: Resets are synchronous
drm/tegra: dc: Document tegra_dc_state_setup_clock()
drm/tegra: dc: Remove unused callbacks
drm/tegra: dc: Remove unused function
drm/tegra: dc: Use base atomic state helpers
drm/atomic: Add helpers for state-subclassing drivers
drm/tegra: dc: Implement hardware VBLANK counter
gpu: host1x: Export host1x_syncpt_read()
drm/tegra: sor: Dump registers via debugfs
drm/tegra: sor: Registers are 32-bit
drm/tegra: Provide debugfs file for the IOVA space
drm/tegra: dc: Check for valid parent clock
As there isn't a way for the firmware on the Nyan Chromebooks to hand
over the display to the kernel, and the kernel isn't redoing the whole
configuration at present.
With this patch, the SOR is brought to a known state and we get correct
display on every boot.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This function is called by output drivers so should be documented. While
at it, move it to a more appropriate location.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The ->mode_set() and ->mode_set_base() callbacks are no longer used with
full atomic mode-setting drivers, so remove them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The tegra_dc_setup_clock() function is unused after the conversion to
atomic mode-setting, so remove it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Instead of duplicating the code, make use of the newly introduced atomic
state duplicate and destroy helpers. This allows changes to the base
atomic state handling to automatically propagate to the Tegra driver and
thereby prevent breakage resulting from both copies going out of sync.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The display controller on Tegra can use syncpoints to count VBLANK
events. syncpoints are 32-bit unsigned integers, so well suited as
VBLANK counters.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use a sized unsigned 32-bit data type (u32) to store register contents.
The SOR registers are 32 bits wide irrespective of the architecture's
data width.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra DRM driver uses a single IO virtual address space for buffer
mappings. Provide a table of the address space usage in debugfs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Check that the desired parent clock is indeed a valid parent for the
display controller clock. This is purely cosmetic at this point since
the parent clocks are specified in DT and all the currently defined
parents are in fact valid parents of the display controller clock.
Signed-off-by: Thierry Reding <treding@nvidia.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU/NacAAoJEHm+PkMAQRiGdUcIAJU5dHclwd9HRc7LX5iOwYN6
mN0aCsYjMD8Pjx2VcPCgJvkIoESQO5pkwYpFFWCwILup1bVEidqXfr8EPOdThzdh
kcaT0FwUvd19K+0jcKVNCX1RjKBtlUfUKONk6sS2x4RrYZpv0Ur8Gh+yXV8iMWtf
fAusNEYlxQJvEz5+NSKw86EZTr4VVcykKLNvj+/t/JrXEuue7IG8EyoAO/nLmNd2
V/TUKKttqpE6aUVBiBDmcMQl2SUVAfp5e+KJAHmizdDpSE80nU59UC1uyV8VCYdM
qwHXgttLhhKr8jBPOkvUxl4aSXW7S0QWO8TrMpNdEOeB3ZB8AKsiIuhe1JrK0ro=
=Xkue
-----END PGP SIGNATURE-----
Merge tag 'v4.0-rc3' into drm-next
Linux 4.0-rc3 backmerge to fix two i915 conflicts, and get
some mainline bug fixes needed for my testing box
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/intel_display.c
Use cases like rotation require these hooks to have some context so they
know how to prepare and cleanup the frame buffer correctly.
For i915 specifically, object backing pages need to be mapped differently
for different rotation modes and the driver needs to know which mapping to
instantiate and which to tear down when transitioning between them.
v2: Made passed in states const. (Daniel Vetter)
[airlied: add mdp5 and atmel fixups]
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These names only make sense because of backwards compatability with
the order used by the crtc helper library. There's not really any real
requirement in the ordering here.
So rename them to something more descriptive and update the kerneldoc
a bit. Motivated in a discussion with Laurent about how to restore
plane state for dpms for drivers with runtime pm.
v2: Squash in fixup from Stephen Rothwell to fix a conflict with
tegra.
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The code in tegra_crtc_prepare() really belongs in tegra_dc_init(), or
at least most of it. This fixes an issue with VBLANK handling because
tegra_crtc_prepare() would overwrite the interrupt mask register that
tegra_crtc_enable_vblank() had written to to enable VBLANK interrupts.
Tested-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Store a pointer to the CRTC in its atomic state to make it easy for
state handling code to get at the CRTC.
Tested-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit eab3bbeffd ("drm/atomic: Add drm_crtc_state->active") added the
field to track the DPMS state. However, the Tegra driver was in modified
in parallel and subclasses the CRTC atomic state, so needed to duplicate
the code in the atomic helpers. After the addition of the active_changed
field it became out of sync and doesn't reset it when duplicating state.
This causes a full modeset on things like page-flips, which will in turn
cause warnings due to the VBLANK machinery being disabled when it really
should remain on.
Tested-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Recent changes in the clock framework have caused a behavioural change
in that clocks that have not had their rate set explicitly will now be
reset to their initial rate (or 0) when the clock is released. This is
triggered in the deferred probing path, resulting in the clock running
at a wrong frequency after the successful probe.
This can be easily fixed by setting the rate explicitly rather than by
relying on the implicit rate inherited by the parent.
Tested-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When copying a relocation from userspace, copy the correct target
offset.
Signed-off-by: David Ung <davidu@nvidia.com>
Fixes: 961e3beae3 ("drm/tegra: Make job submission 64-bit safe")
Cc: stable@vger.kernel.org
[treding@nvidia.com: provide a better commit message]
Signed-off-by: Thierry Reding <treding@nvidia.com>
For now only disable the KMS hotplug polling helper logic upon suspend
and re-enable it on resume.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Previously output drivers would enable continuous display mode and power
up the display controller at various points during the initialization.
This is suboptimal because it accesses display controller registers in
output drivers and duplicates a bit of code.
Move this code into the display controller driver and enable the display
controller as the final step of the ->mode_set_nofb() implementation.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tracking these in the plane state allows them to be computed in the
->atomic_check() callback and reused when applying the configuration in
->atomic_update().
Signed-off-by: Thierry Reding <treding@nvidia.com>
Wrap struct drm_crtc_state in a driver-specific structure and add the
planes field which keeps track of which planes are updated or disabled
during a modeset. This allows atomic updates of the the display engine
at ->atomic_flush() time.
v2: open-code getting the state of the CRTC that the plane is being
attached to (Daniel Vetter)
Signed-off-by: Thierry Reding <treding@nvidia.com>
All output drivers have now been converted to use the ->atomic_check()
callback, so the ->mode_fixup() callbacks are no longer used.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Provide a custom ->atomic_commit() implementation which supports async
commits. The generic atomic page-flip helper can use this to implement
page-flipping.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Replace drm_crtc_helper_set_config() by drm_atomic_helper_set_config().
All drivers have now been converted to use ->atomic_check() to set the
atomic state, therefore the atomic mode setting helpers can be used.
Signed-off-by: Thierry Reding <treding@nvidia.com>
All clock state is now stored in the display controller's atomic state,
so the output drivers no longer need to call back into the display
controller driver to set up the clock. This is also required to make
sure no hardware changes are made before validating a configuration.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The implementation of the ->atomic_check() callback precomputes all
parameters to check if the given configuration can be applied. If so the
precomputed values are stored in the atomic state object for the encoder
and applied during modeset. In that way the modeset no longer needs to
perform any checking but simply program values into registers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The implementation of the ->atomic_check() callback precomputes all
parameters to check if the given configuration can be applied. If so the
precomputed values are stored in the atomic state object for the encoder
and applied during modeset. In that way the modeset no longer needs to
perform any checking but simply program values into registers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The implementation of the ->atomic_check() callback precomputes all
parameters to check if the given configuration can be applied. If so the
precomputed values are stored in the atomic state object for the encoder
and applied during modeset. In that way the modeset no longer needs to
perform any checking but simply program values into registers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The implementation of the ->atomic_check() callback precomputes all
parameters to check if the given configuration can be applied. If so the
precomputed values are stored in the atomic state object for the encoder
and applied during modeset. In that way the modeset no longer needs to
perform any checking but simply program values into registers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This allows the clock setup to be separated from the clock programming
and better matches the expectations of the atomic modesetting where no
code paths must fail during modeset.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Switch out the regular plane helpers for the atomic plane helpers. Also
use the default atomic helpers to implement the ->atomic_check() and
->atomic_commit() callbacks. The driver now exclusively uses the atomic
interfaces.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Hook up the default ->reset() and ->atomic_duplicate_state() helpers.
This ensures that state objects are properly created and framebuffer
reference counts correctly maintained.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Implement initial atomic state handling. Hook up the CRTCs, planes' and
connectors' ->atomic_destroy_state() callback to ensure that the atomic
state objects don't leak.
Furthermore the CRTC now implements the ->mode_set_nofb() callback that
is used by new helpers to implement ->mode_set() and ->mode_set_base().
These new helpers also make use of the new plane helper functions which
the driver now provides.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit 9c0127004f ("drm/tegra: dc: Add powergate support") changed the
driver's ->probe() implementation to deassert the module reset, and with
there being nobody else to assert it until ->remove() there is no need
to deassert again later on.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The tegra_output midlayer is now completely gone and output drivers use
it purely as a helper library.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The debugfs cleanup code never fails, so no error is returned. Therefore
the functions can all return void instead.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Implement encoder and connector within the eDP driver itself using the
Tegra output helpers rather than using the Tegra output as midlayer. By
doing so one level of indirection is removed and output drivers become
more flexible while keeping the majority of the advantages provided by
the common output helpers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Implement encoder and connector within the DSI driver itself using the
Tegra output helpers rather than using the Tegra output as midlayer. By
doing so one level of indirection is removed and output drivers become
more flexible while keeping the majority of the advantages provided by
the common output helpers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Implement encoder and connector within the HDMI driver itself using the
Tegra output helpers rather than using the Tegra output as midlayer. By
doing so one level of indirection is removed and output drivers become
more flexible while keeping the majority of the advantages provided by
the common output helpers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Implement encoder and connector within the RGB driver itself using the
Tegra output helpers rather than using the Tegra output as midlayer. By
doing so one level of indirection is removed and output drivers become
more flexible while keeping the majority of the advantages provided by
the common output helpers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This is a small helper that performs the basic steps required by all
output drivers to prepare the display controller for use with a given
encoder.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to transition output drivers to using the struct tegra_output
as a helper rather than midlayer, make this callback optional. Instead
drivers should implement the equivalent as part of ->mode_fixup(). For
the conversion to atomic modesetting a new callback ->atomic_check()
should be implemented that updates the display controller's state with
the corresponding parent clock, rate and shift clock divider.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The output layer was initially designed to help reduce the amount of
code duplicated in output drivers. An unfortunate side-effect of that
was that it turned into a midlayer and it became difficult to make the
output drivers work without bending over backwards to fit into the
midlayer.
This commit starts to convert the midlayer into a helper library by
exporting most of the common functions so that they can be used by the
output drivers directly. Doing so will allow output drivers to reuse
common code paths but more easily override them where necessary.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DRM core should take care of disabling all unneeded planes, so there
is no need to do this explicitly.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This structure will be extended using non-framebuffer related callbacks
in subsequent patches, so it should move to a more central location.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When disabling the display controller, stop it and wait for it to become
idle. Doing so ensures that no further accesses to the framebuffer occur
and the buffers can be safely unmapped or freed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Previously output drivers would all stop the display controller in their
disable path. However with the transition to atomic modesetting the
display controller needs to be kept running until all planes have been
disabled so that software can properly determine (using VBLANK counts)
when it is safe to remove the framebuffers associated with the planes.
Moving this code into the display controller's disable path also gets
rid of the duplication of this into all output drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
All output drivers have open-coded variants of this function, so export
it to remove some code duplication.
Signed-off-by: Thierry Reding <treding@nvidia.com>
kfree(ERR_PTR(-ENOMEM)) will not work very well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
We can't save two values to the IRQ flags at the same time so the IRQs
are not enabled at the end. This kind of bug is easy to miss in testing
if the function is normally called with IRQs disabled so we wouldn't
enable IRQs anyway.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Compliance testing shows that HS Trail is off by -12%. Increase the HS
Trail time to make this test pass.
Signed-off-by: David Ung <davidu@nvidia.com>
[treding@nvidia.com: update specification references, add comment]
Signed-off-by: Thierry Reding <treding@nvidia.com>
This allows a DRM driver unload/reload cycle to completely reset the DSI
controller and may help in situations where it's broken.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use a sized unsigned 32-bit data type (u32) to store register contents.
The DSI registers are 32 bits wide irrespective of the architecture's
data width.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use a sized unsigned 32-bit data type (u32) to store register contents.
The HDMI registers are 32 bits wide irrespective of the architecture's
data width.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Most of the display controller's registers are double-buffered, a few of
them are triple-buffered. The ASSEMBLY shadow copy is latched intto the
ACTIVE copy for double-buffered registers. For triple-buffered registers
the ASSEMBLY copy is first latched into the ARM copy.
Latching into the ACTIVE copy happens immediately if the controller is
inactive. Otherwise the latching happens on the next frame boundary. The
latching of the ASSEMBLY into the ARM copy happens immediately. Latching
is controlled by a set of *_ACT_REQ and *_UPDATE bits in the
DC_CMD_STATE_CONTROL register.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra114 and earlier support specifying the color of the border (i.e.
the active area of the screen that is not covered by any of the overlay
windows). By default this is set to a light blue, so set it to black to
comply with the requirements set by atomic modesetting.
Signed-off-by: Thierry Reding <treding@nvidia.com>
iommu_domain_alloc() returns NULL on error, it never returns error
pointers.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The possible_crtcs mask needs to be a mask of CRTC indices. There is no
guarantee that the DRM indices match the hardware pipe number, so the
mask must be computed from the CRTC index.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DRM core now zeroes out the memory associated with CRTC, encoder and
connector objects upon cleanup, so there's no need to explicitly do that
in drivers anymore.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Previously the struct bus_type exported by the host1x infrastructure was
only a very basic skeleton. Turn that implementation into a more full-
fledged bus to support proper probe ordering and power management.
Note that the bus infrastructure needs to be available before any of the
drivers can be registered. This is automatically ensured if all drivers
are built as loadable modules (via symbol dependencies). If all drivers
are built-in there are no such guarantees and the link order determines
the initcall ordering. Adjust drivers/gpu/Makefile to make sure that the
host1x bus infrastructure is initialized prior to any of its users (only
drm/tegra currently).
v2: Fix building host1x and tegra-drm as modules
Reported-by: Dave Airlie <airlied@gmail.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Misc drm patches with mostly polish patches from Thierry, with a bit of
generic mode validation from Ville and a few other oddball things.
* tag 'topic/core-stuff-2014-12-19' of git://anongit.freedesktop.org/drm-intel: (25 commits)
drm: Include drm_crtc_helper.h in DocBook
drm: Make drm_crtc_helper.h standalone includible
drm: Move IRQ related fields to proper section
drm: Remove stale comment
drm: Do basic sanity checks for user modes
drm: Perform basic sanity checks on probed modes
drm: Reorganize probed mode validation
drm/doc: Remove duplicate "by"
drm/info: Remove unused code
drm/cache: Use wbinvd helpers
drm/plane-helper: Test for plane disable earlier
drm/doc: Document drm_add_modes_noedid() usage
drm: bit of spell-check / editorializing.
drm: Prefer sizeof(type) over sizeof type
drm: Remove useless else block
drm: Remove unneeded braces for single statement blocks
drm: Do not assign in if condition
drm: Prefer kmalloc_array() over kmalloc() with multiply
drm: Prefer kcalloc() over kzalloc() with multiply
drm: Miscellaneous checkpatch whitespace cleanups
...
In finish pageflip, the driver was not selecting the root window when
dispatching events. This exposed a race where a plane update would
change the window selection and cause tegra_dc_finish_page_flip to check
the wrong base address.
This patch also protects access to the window selection register as well
as the registers affected by it.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
If the requested buffer size wasn't a multiple of the page size, the
IOMMU code would round down the size to the next multiple of the page
size, thereby causing translation errors. To fix this we no longer pass
around the requested size but reuse the computed size of the GEM object.
This is already rounded to the next page boundary, so mapping that size
works out fine.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Buffers obtained via shmem may still have associated cachelines. If they
aren't properly flushed they may cause framebuffer corruption if the
cache gets flushed after the application has drawn to it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Page-flip completion could race with page-flip submission, so extend the
critical section to include all accesses to page-flip related data.
Reported-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The hardware pipe numbers don't always match the DRM CRTC indices. This
can happen for example if the first display controller defers probe,
causing it to be registered with DRM after the second display
controller. When that happens the hardware pipe numbers and DRM CRTC
indices become different. Make sure that the CRTC index is always used
when accessing per-CRTC VBLANK data. This can be ensured by using the
drm_crtc_vblank_*() API, which will do the right thing automatically
given a struct drm_crtc *.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The ->load_lut() callback is optional, therefore a dummy implementation
is not needed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The highlights in this pull request are:
* IOMMU support: The Tegra DRM driver can now deal with discontiguous
buffers if an IOMMU exists in the system. That means it can allocate
using drm_gem_get_pages() and will map them into IOVA space via the
IOMMU API. Similarly, non-contiguous PRIME buffers can be imported
from a different driver, which allows better integration with gk20a
(nouveau) and less hacks.
* Universal planes: This is precursory work for atomic modesetting and
will allow hardware cursor support to be implemented on pre-Tegra114
where RGB cursors were not supported.
* DSI ganged-mode support: The DSI controller can now gang up with a
second DSI controller to drive high resolution DSI panels.
Besides those bigger changes there is a slew of fixes, cleanups, plugged
memory leaks and so on.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=v4QW
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-3.19-rc1' of git://people.freedesktop.org/~tagr/linux into drm-next
drm/tegra: Changes for v3.19-rc1
The highlights in this pull request are:
* IOMMU support: The Tegra DRM driver can now deal with discontiguous
buffers if an IOMMU exists in the system. That means it can allocate
using drm_gem_get_pages() and will map them into IOVA space via the
IOMMU API. Similarly, non-contiguous PRIME buffers can be imported
from a different driver, which allows better integration with gk20a
(nouveau) and less hacks.
* Universal planes: This is precursory work for atomic modesetting and
will allow hardware cursor support to be implemented on pre-Tegra114
where RGB cursors were not supported.
* DSI ganged-mode support: The DSI controller can now gang up with a
second DSI controller to drive high resolution DSI panels.
Besides those bigger changes there is a slew of fixes, cleanups, plugged
memory leaks and so on.
* tag 'drm/tegra/for-3.19-rc1' of git://people.freedesktop.org/~tagr/linux: (44 commits)
drm/tegra: gem: Check before freeing CMA memory
drm/tegra: fb: Add error codes to error messages
drm/tegra: fb: Properly release GEM objects on failure
drm/tegra: Detach panel when a connector is removed
drm/tegra: Plug memory leak
drm/tegra: gem: Use more consistent data types
drm/tegra: fb: Do not destroy framebuffer
drm/tegra: gem: dumb: pitch and size are outputs
drm/tegra: Enable the hotplug interrupt only when necessary
drm/tegra: dc: Universal plane support
drm/tegra: dc: Registers are 32 bits wide
drm/tegra: dc: Factor out DC, window and cursor commit
drm/tegra: Add IOMMU support
drm/tegra: Fix error handling cleanup
drm/tegra: gem: Use dma_mmap_writecombine()
drm/tegra: gem: Remove redundant drm_gem_free_mmap_offset()
drm/tegra: gem: Cleanup tegra_bo_create_with_handle()
drm/tegra: gem: Extract tegra_bo_alloc_object()
drm/tegra: dsi: Set up PHY_TIMING & BTA_TIMING registers earlier
drm/tegra: dsi: Replace 1000000 by USEC_PER_SEC
...
dma_free_writecombine() must not be called on a buffer that couldn't be
allocated. Check for a valid virtual address before attempting to free
the memory to avoid a crash.
Reported-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When fbdev initialization fails, make sure to unreference the GEM
objects properly. Note that we can't do this in the general error
unwinding path because ownership of the GEM object references is
transferred to the framebuffer upon creation.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When the DRM device is torn down and the connector is removed, make sure
to detach the panel to make sure there are no dangling pointers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Drop a reference instead of directly calling the framebuffer .destroy()
callback at fbdev free time. This is necessary to make sure the object
isn't destroyed if anyone else still has a reference.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When creating a dumb buffer object using the DRM_IOCTL_MODE_CREATE_DUMB
IOCTL, only the width, height, bpp and flags parameters are inputs. The
caller is not guaranteed to zero out or set handle, pitch and size, so
the driver must not treat these values as possible inputs.
Fixes a bug where running the Weston compositor on Tegra DRM would cause
an attempt to allocate a 3 GiB framebuffer to be allocated.
Fixes: de2ba664c3 ("gpu: host1x: drm: Add memory manager and fb")
Cc: stable@vger.kernel.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
The hotplug handling needs access to the DRM device, which only appears
at ->init() time. Disable interrupts up until that time. Similarly, when
an output is removed, disable the hotplug interrupt again because the
DRM device (and with it the hotplug infrastructure) is going away.
Also make sure to only access the DRM device if it's available. Given
the above change for the hotplug interrupt this should really never
happen, but the extra check doesn't hurt either.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This allows the primary plane and cursor to be exposed as regular
DRM/KMS planes, which is a prerequisite for atomic modesetting and gives
userspace more flexibility over controlling them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Using an unsigned long type will cause these variables to become 64-bit
on 64-bit SoCs. In practice this should always work, but there's no need
for carrying around the additional 32 bits.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The sequence to commit changes to the DC, window or cursor configuration
is repetitive and can be extracted into separate functions for ease of
use.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When an IOMMU device is available on the platform bus, allocate an IOMMU
domain and attach the display controllers to it. The display controllers
can then scan out non-contiguous buffers by mapping them through the
IOMMU.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DRM driver's ->load() implementation didn't do a good job (no job at
all really) cleaning up on failure. Fix that by undoing any prior setup
when an error occurs. This requires a bit of rework to make it possible
to clean up fbdev midway.
This was tested by injecting errors at various points during the
initialization sequence and verifying that error cleanup didn't crash
and no memory leaked (using kmemleak).
Reported-by: Stéphane Marchesin <marcheu@chromium.org>
Reported-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The drm_gem_object_release() function already performs this cleanup, so
there is no reason to do it explicitly.
Signed-off-by: Thierry Reding <treding@nvidia.com>
There is only a single location where the function needs to do cleanup.
Skip the error unwinding path and call the cleanup function directly
instead.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This function implements the common buffer object allocation used for
both allocation and import paths.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Make sure the DSI PHY_TIMING and BTA_TIMING registers are initialized
when the clocks are set up as opposed to when the output is enabled.
This makes sure that the PHY timings are properly set up when the panel
is prepared and that DCS commands sent at that time use the appropriate
timings.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for sending MIPI DSI command packets from the host to a
peripheral. This is required for panels that need configuration before
they accept video data.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Implement ganged mode support for the Tegra DSI driver. The DSI host
controller to gang up with is specified via a phandle in the device tree
and the resolved DSI host controller used for the programming of the
ganged-mode registers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In preparation for adding ganged-mode support, this commit splits out
the tegra_dsi_set_timeout() function so that it can be reused for the
slave DSI controller.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for DC-driven command mode. This is a mode where the video
stream sent by the display controller is packed into DCS command packets
(write_memory_start and write_memory_continue) by the DSI controller. It
can be used for panels with a remote framebuffer and is useful to save
power when used with a dynamic refresh rate (not yet supported by the
driver).
Signed-off-by: Thierry Reding <treding@nvidia.com>
For command mode panels, the DSI controller needs to be enabled and
configured so that panel drivers can send commands prior to the video
stream being enabled.
Move code from the monolithic output enable/disable functions into
smaller, reusable units to allow more fine-grained control over the
controller state.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The driver wasn't even attempting to do any cleanup when probing failed.
Fix this by releasing any resources acquired up to the point of failure
and putting the device back into the original state (reset, clocks off).
Signed-off-by: Thierry Reding <treding@nvidia.com>
DSI panels can always be hotplugged via the DSI bus' attach/detach
infrastructure, so unconditionally mark the connector hotpluggable.
While at it, also make sure that when a panel is detached the connector
is marked unconnected before calling into the DRM hotplug helpers to
reflect the correct state.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The common clock framework will take care of preparing and enabling the
parent of the DSI clock automatically.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In preparation for supporting command mode panels, don't disable the
clock when the output is disabled. The output will be enabled only after
the panel has been programmed in command mode, so the clock must always
remain on.
As a side-effect, pad calibration now only needs to be done at driver
probe time, since neither power nor controller state will go away before
driver removal. While at it, use a 32-bit variable to store register
content because the registers are 32-bit even on 64-bit Tegra.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rather than hardcoding them as macros, make the host and video FIFO
depths parameters so that they can be more easily adjusted if a new
generation of the Tegra SoC changes them.
While at it, set the depth of the video FIFO to the correct value of
1920 *words* rather than *bytes*.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Previously the panel and output were only enabled on encoder->dpms(). If
userspace called dpms on before doing a modeset, the driver would get into
a state where the connector had a dpms state of ON, but the encoder and output
were not enabled (because the encoder is not yet attached to the connector).
Subsequent dpms ON calls are ignored b/c the connector's state already matches
the desired state.
This patch enables/disables the panel and output on modeset as well, so we
can catch the above case.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Both display controllers are in their own power partition. Currently the
driver relies on the assumption that these partitions are on (which is
the hardware default). However some bootloaders may disable them, so the
driver must make sure to turn them back on to avoid hangs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The introduction of the COMPILE_TEST dependency in commit 158b50aefa
(drm/tegra: Increase compile test coverage) removes the dependency on
COMMON_CLK (implicitly selected via ARCH_TEGRA, ARCH_MULTI_V7 and
ARCH_MULTIPLATFORM).
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When the CRTC is enabled, make sure the VBLANK machinery is enabled.
Failure to do so will cause drm_vblank_get() to not enable the VBLANK on
the CRTC and VBLANK-synchronized page-flips won't work.
While at it, get rid of the legacy drm_vblank_pre_modeset() and
drm_vblank_post_modeset() calls that are replaced by drm_vblank_on()
and drm_vblank_off().
Reported-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Just a bit of OCD cleanup on headers - this function isn't the core
interface any more but just a helper for drivers who haven't yet
transitioned to universal planes. Put the declaration at the right
spot and sprinkle necessary #includes over all drivers.
Maybe this helps to encourage driver maintainers to do the switch.
v2: Fix #include ordering for tegra, reported by 0-day builder.
v3: Include required headers, reported by Thierry.
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Thierry Reding <treding@nvidia.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
v2: Don't forget git add, noticed by David.
Cc: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Acked-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Rename the defines to have levels instead of values for vswing and
pre-emph levels as the values may differ in other scenarios like low vswing of
eDP1.4 where the values are different.
Done using following cocci patch for each define:
@@
@@
# define DP_TRAIN_VOLTAGE_SWING_400 (0 << 0)
+ # define DP_TRAIN_VOLTAGE_SWING_LEVEL_0 (0 << 0)
...
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This merge window brings a good size of cleanups on various
platforms. Among the bigger ones:
* Removal of Samsung s5pc100 and s5p64xx platforms. Both of these have
lacked active support for quite a while, and after asking around nobody
showed interest in keeping them around. If needed, they could be
resurrected in the future but it's more likely that we would prefer
reintroduction of them as DT and multiplatform-enabled platforms
instead.
* OMAP4 controller code register define diet. They defined a lot of registers
that were never actually used, etc.
* Move of some of the Tegra platform code (PMC, APBIO, fuse, powergate)
to drivers/soc so it can be shared with 64-bit code. This also converts them
over to traditional driver models where possible.
* Removal of legacy gpio-samsung driver, since the last users have been
removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some misc
cleanups, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJT5DYPAAoJEIwa5zzehBx37egQAIiatNiLLqZnfo3rwGADRz/a
POfPovktj68aPcobyzoyhFtToMqGvi9PpysyFTIQD2HJFG+5BtiIAuqtg0875zDe
EpBWgsfugrm0YktJWAtUerj60oAmNPbKfaEm1cOOWuM2lb2mV+QkRrwSTAgsqkT7
927BzMXKKBRPOVLL0RYhoF8EXa0Eg8kCqAHP8fJrzVYkRp+UrZJDnGiUP1XmWJN+
VXQMu5SEjcPMtqT7+tfX455RfREHJfBcJ1ZN/dPF8HMWDwClQG0lyc6hifh1MxwO
8DjIZNkfZeKqgDqVyC17re7pc7p8md5HL8WXbrKpK0A9vQ5bRexbPHxcwJ1T/C2Y
465H+st5XXbuzV1gbMwjK1/ycsH0tCyffckk8Yl/2e1Fs7GgPNbAELtTdl+5vV1Y
xmDXkyo/9WlRM3LQ23IGKwW7VzN86EfWVuShssfro0fO7xDdb4OOYLdQI+4bCG+h
ytQYun1vU32OEyNik5RVNQuZaMrv2c93a3bID4owwuPHPmYOPVUQaqnRX/0E51eA
aHZYbk2GlUOV3Kq5aSS4iyLg1Yj+I9/NeH9U+A4nc+PQ5FlgGToaVSCuYuw4DqbP
AAG+sqQHbkBMvDPobQz/yd1qZbAb4eLhGy11XK1t5S65rApWI55GwNXnvbyxqt8x
wpmxJTASGxcfuZZgKXm7
=gbcE
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This merge window brings a good size of cleanups on various platforms.
Among the bigger ones:
- Removal of Samsung s5pc100 and s5p64xx platforms. Both of these
have lacked active support for quite a while, and after asking
around nobody showed interest in keeping them around. If needed,
they could be resurrected in the future but it's more likely that
we would prefer reintroduction of them as DT and
multiplatform-enabled platforms instead.
- OMAP4 controller code register define diet. They defined a lot of
registers that were never actually used, etc.
- Move of some of the Tegra platform code (PMC, APBIO, fuse,
powergate) to drivers/soc so it can be shared with 64-bit code.
This also converts them over to traditional driver models where
possible.
- Removal of legacy gpio-samsung driver, since the last users have
been removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some
misc cleanups, etc"
* tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (117 commits)
drivers: CCI: Correct use of ! and &
video: clcd-versatile: Depend on ARM
video: fix up versatile CLCD helper move
MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
MAINTAINERS: Remove Kirkwood
ARM: tegra: Convert PMC to a driver
soc/tegra: fuse: Set up in early initcall
ARM: tegra: Always lock the CPU reset vector
ARM: tegra: Setup CPU hotplug in a pure initcall
soc/tegra: Implement runtime check for Tegra SoCs
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
ARM: tegra: move fuse exports to soc/tegra/fuse.h
ARM: tegra: export apb dma readl/writel
ARM: tegra: Use a function to get the chip ID
ARM: tegra: Sort includes alphabetically
ARM: tegra: Move includes to include/soc/tegra
...
Pull DRM updates from Dave Airlie:
"Like all good pull reqs this ends with a revert, so it must mean we
tested it,
[ Ed. That's _one_ way of looking at it ]
This pull is missing nouveau, Ben has been stuck trying to track down
a very longstanding bug that revealed itself due to some other
changes. I've asked him to send you a direct pull request for nouveau
once he cleans things up. I'm away until Monday so don't want to
delay things, you can make a decision on that when he sends it, I have
my phone so I can ack things just not really merge much.
It has one trivial conflict with your tree in armada_drv.c, and also
the pull request contains some component changes that are already in
your tree, the base tree from Russell went via Greg's tree already,
but some stuff still shows up in here that doesn't when I merge my
tree into yours.
Otherwise all pretty standard graphics fare, one new driver and
changes all over the place.
New drivers:
- sti kms driver for STMicroelectronics chipsets stih416 and stih407.
core:
- lots of cleanups to the drm core
- DP MST helper code merged
- universal cursor planes.
- render nodes enabled by default
panel:
- better panel interfaces
- new panel support
- non-continuous cock advertising ability
ttm:
- shrinker fixes
i915:
- hopefully ditched UMS support
- runtime pm fixes
- psr tracking and locking - now enabled by default
- userptr fixes
- backlight brightness fixes
- MST support merged
- runtime PM for dpms
- primary planes locking fixes
- gen8 hw semaphore support
- fbc fixes
- runtime PM on SOix sleep state hw.
- mmio base page flipping
- lots of vlv/chv fixes.
- universal cursor planes
radeon:
- Hawaii fixes
- display scalar support for non-fixed mode displays
- new firmware format support
- dpm on more asics by default
- GPUVM improvements
- uncached and wc GTT buffers
- BOs > visible VRAM
exynos:
- i80 interface support
- module auto-loading
- ipp driver consolidated.
armada:
- irq handling in crtc layer only
- crtc renumbering
- add component support
- DT interaction changes.
tegra:
- load as module fixes
- eDP bpp and sync polarity fixed
- DSI non-continuous clock mode support
- better support for importing buffers from nouveau
msm:
- mdp5/adq8084 v1.3 hw enablement
- devicetree clk changse
- ifc6410 board working
tda998x:
- component support
- DT documentation update
vmwgfx:
- fix compat shader namespace"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (551 commits)
Revert "drm: drop redundant drm_file->is_master"
drm/panel: simple: Use devm_gpiod_get_optional()
drm/dsi: Replace upcasting macro by function
drm/panel: ld9040: Replace upcasting macro by function
drm/exynos: dp: Modify driver to support drm_panel
drm/exynos: Move DP setup into commit()
drm/panel: simple: Add AUO B133HTN01 panel support
drm/panel: simple: Support delays in panel functions
drm/panel: simple: Add proper definition for prepare and unprepare
drm/panel: s6e8aa0: Add proper definition for prepare and unprepare
drm/panel: ld9040: Add proper definition for prepare and unprepare
drm/tegra: Add support for panel prepare and unprepare routines
drm/exynos: dsi: Add support for panel prepare and unprepare routines
drm/exynos: dpi: Add support for panel prepare and unprepare routines
drm/panel: simple: Add dummy prepare and unprepare routines
drm/panel: s6e8aa0: Add dummy prepare and unprepare routines
drm/panel: ld9040: Add dummy prepare and unprepare routines
drm/panel: Provide convenience wrapper for .get_modes()
drm/panel: add .prepare() and .unprepare() functions
drm/panel: simple: Remove simple-panel compatible
...
Mostly some cleanup all over the place. Pitch alignment limitations of
the display controller are now honored and job submission is 64-bit
safe.
The SOR output (used for eDP) properly configures sync signal polarities
according to the display mode rather than hard-coding them to some value
and the number of bits per color is now taken from the panel rather than
hard-coded to properly support 24-bit vs. 18-bit panels.
The DSI controller now properly supports non-continuous clock mode.
GEM objects can now have their flags and tiling mode modified via IOCTLs
to allow buffers imported from Nouveau to be properly displayed. Newer
generations of the Tegra display controller can also detile block linear
buffers at scan-out time.
Finally the driver now properly exports MODULE_DEVICE_TABLEs to allow it
to be automatically loaded when built as a module.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=qYgE
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-3.17-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v3.17-rc1
Mostly some cleanup all over the place. Pitch alignment limitations of
the display controller are now honored and job submission is 64-bit
safe.
The SOR output (used for eDP) properly configures sync signal polarities
according to the display mode rather than hard-coding them to some value
and the number of bits per color is now taken from the panel rather than
hard-coded to properly support 24-bit vs. 18-bit panels.
The DSI controller now properly supports non-continuous clock mode.
GEM objects can now have their flags and tiling mode modified via IOCTLs
to allow buffers imported from Nouveau to be properly displayed. Newer
generations of the Tegra display controller can also detile block linear
buffers at scan-out time.
Finally the driver now properly exports MODULE_DEVICE_TABLEs to allow it
to be automatically loaded when built as a module.
* tag 'drm/tegra/for-3.17-rc1' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: add MODULE_DEVICE_TABLEs
drm/tegra: dc - Reset controller on driver remove
drm/tegra: Properly align stride for framebuffers
drm/tegra: sor - Configure proper sync polarities
drm/tegra: sor - Use bits-per-color from panel
drm/tegra: Make job submission 64-bit safe
drm/tegra: Allow non-authenticated processes to create buffer objects
drm/tegra: Add SET/GET_FLAGS IOCTLs
drm/tegra: Add SET/GET_TILING IOCTLs
drm/tegra: Implement more tiling modes
drm/tegra: dsi - Handle non-continuous clock flag
drm/tegra: sor - missing unlock on error
Panels can now be more finely controlled via .prepare() and .unprepare()
callbacks in addition to .enable() and .disable(). New kerneldoc details
what they are supposed to do and when they should be called.
The simple panel driver gained support for a couple of new panels and it
is now possible to specify additional delays during power up and power
down sequences if panels require it.
DSI devices can now advertise that they support non-continuous clock
mode which will allow DSI host controllers to disable the high speed
clock after transmissions to save power.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=vf7m
-----END PGP SIGNATURE-----
Merge tag 'drm/panel/for-3.17-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/panel: Changes for v3.17-rc1
Panels can now be more finely controlled via .prepare() and .unprepare()
callbacks in addition to .enable() and .disable(). New kerneldoc details
what they are supposed to do and when they should be called.
The simple panel driver gained support for a couple of new panels and it
is now possible to specify additional delays during power up and power
down sequences if panels require it.
DSI devices can now advertise that they support non-continuous clock
mode which will allow DSI host controllers to disable the high speed
clock after transmissions to save power.
* tag 'drm/panel/for-3.17-rc1' of git://anongit.freedesktop.org/tegra/linux: (30 commits)
drm/panel: simple: Use devm_gpiod_get_optional()
drm/dsi: Replace upcasting macro by function
drm/panel: ld9040: Replace upcasting macro by function
drm/exynos: dp: Modify driver to support drm_panel
drm/exynos: Move DP setup into commit()
drm/panel: simple: Add AUO B133HTN01 panel support
drm/panel: simple: Support delays in panel functions
drm/panel: simple: Add proper definition for prepare and unprepare
drm/panel: s6e8aa0: Add proper definition for prepare and unprepare
drm/panel: ld9040: Add proper definition for prepare and unprepare
drm/tegra: Add support for panel prepare and unprepare routines
drm/exynos: dsi: Add support for panel prepare and unprepare routines
drm/exynos: dpi: Add support for panel prepare and unprepare routines
drm/panel: simple: Add dummy prepare and unprepare routines
drm/panel: s6e8aa0: Add dummy prepare and unprepare routines
drm/panel: ld9040: Add dummy prepare and unprepare routines
drm/panel: Provide convenience wrapper for .get_modes()
drm/panel: add .prepare() and .unprepare() functions
drm/panel: simple: Remove simple-panel compatible
drm/panel: simple: Add Innolux N116BGE panel support
...
Modify tegra output driver to support the new panel calls:
prepare and unprepare.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When tegra-drm.ko is built as a module, these MODULE_DEVICE_TABLEs allow
the module to be auto-loaded since the module will match the devices
instantiated from device tree.
(Notes for stable: in 3.14+, just git rm any conflicting file, since they
are added in later kernels. For 3.13 and below, manual merging will be
needed)
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Since the device will no longer be used, may as well keep it in reset to
potentially save some power and make sure it is in a clean state the
next time it's probed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra20 and Tegra30 both required the buffer line stride to be aligned
on 8 byte boundaries. Tegra114 and Tegra124 increased the alignment to
64 bytes. Introduce a parameter to specify the alignment requirements
for each display controller and round up the pitch of newly allocated
framebuffers appropriately.
Originally-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This change uses the value of bits-per-color from panel to remove one
more hardcoded value.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Job submission currently relies on the fact that struct drm_tegra_reloc
and struct host1x_reloc are the same size and uses a simple call to the
copy_from_user() function to copy them to kernel space. This causes the
handle to be stored in the buffer object field, which then needs a cast
to a 32 bit integer to resolve it to a proper buffer object pointer and
store it back in the buffer object field.
On 64-bit architectures that will no longer work, since pointers are 64
bits wide whereas handles will remain 32 bits. This causes the sizes of
both structures to because different and copying will no longer work.
Fix this by adding a new function, host1x_reloc_get_user(), that copies
the structures field by field.
While at it, use substructures for the command and target buffers in
struct host1x_reloc for better readability. Also use unsized types to
make it more obvious that this isn't part of userspace ABI.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This matches what other drivers do for equivalent IOCTLs.
Reviewed-by: Stéphane Marchesin <marcheu@chromium.org>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DRM_TEGRA_GEM_SET_FLAGS IOCTL can be used to set the flags of a
buffer object after it has been allocated or imported. Flags associated
with a buffer object can be queried using the DRM_TEGRA_GEM_GET_FLAGS
IOCTL.
Reviewed-by: Stéphane Marchesin <marcheu@chromium.org>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently the tiling parameters of buffer objects can only be set at
allocation time, and only a single tiled mode is supported. This new
DRM_TEGRA_GEM_SET_TILING IOCTL allows more modes to be set and also
allows the tiling mode to be changed after the allocation. This will
enable the Tegra DRM driver to import buffers from a GPU and directly
scan them out by configuring the display controller appropriately.
To complement this, the DRM_TEGRA_GEM_GET_TILING IOCTL can query the
current tiling mode of a buffer object. This is necessary when importing
buffers via handle (as is done in Mesa for example) so that userspace
can determine the proper parameters for the 2D or 3D engines.
Reviewed-by: Stéphane Marchesin <marcheu@chromium.org>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra124 supports a block-linear mode in addition to the regular pitch
linear and tiled modes. Add support for these by moving the internal
representation into a structure rather than a simple flag.
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Handle the MIPI_DSI_CLOCK_NONCONTINUOUS flag and only set TX-only
clock behavior when this flag is present to allow panels requiring
continuous clock mode to operate with this driver.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
We should unlock before returning the error code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit converts the PMC support code to a platform driver. Because
the boot process needs to call into this driver very early, also set up
a minimal environment via an early initcall.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to not clutter the include/linux directory with SoC specific
headers, move the Tegra-specific headers out into a separate directory.
Signed-off-by: Thierry Reding <treding@nvidia.com>
