ath9k_hw_set_diversity is only called from init.c where it cannot affect
the hardware setting because it's cleared on the next reset.
Instead of using a PHY op for something that's supposed to be initialized
statically, set the register value directly in the INI override function.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The eeprom .set_addac function is only necessary for AR9160, remove it
from eeprom_4k.c and remove the dummy function from eeprom_9287.c
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- AR_SREV_5416_20_OR_LATER is always true, remove it
- AR_SREV_9280_20_OR_LATER is always true within eeprom_4k.c and eeprom_9287.c
- (AR_SREV_9271 || AR_SREV_9285) is always true in eeprom_4k.c
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add function to find vendor-specific ie (along with
vendor-specific ie struct definition and P2P OUI values)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the driver inserts padding between the 802.11 header and data, it
needs to set the hdr variable to the new header location.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's not in staging anymore and I'm the current maintainer.
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Cc: Naveen Singh <nvesing@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the new EDMA descriptor format, a single descriptor can contain up
to four buffer pointers. By splitting the buffer into two parts, we can
let the hardware add the padding internally instead of using memmove on
the skb data.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The only flag that needs to be set when ath_tx_rc_status is called with
rc_update == false is the IEEE80211_TX_STAT_TX_FILTERED flag. All other
data is ignored in that case.
This flag can be set from ath_tx_complete_buf instead, so that we can
drop a few redundant calls to ath_tx_rc_status and remove the rc_update
function parameter
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_lookup_legacy now checks all the tx rate flags for MCS vs legacy
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_hw_cycle_counters_update only needs to be called if the power state
changes. Most of the time this does not happen, even when ps_usecount
goes down to 0.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the new API, tx descriptors can be written in one single pass
instead of having to re-read and rewrite fields from multiple places.
This makes the code easier to read and also slightly improves performance
on embedded MIPS hardware.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using lots of different functions with long argument lists,
pull all the necessary information from one struct. This makes the code
easier to read and eliminates the need for copying data between multiple
linked descriptors.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduces the number of accesses to uncached descriptor memory.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This ensures that only ath9k_hw_set_desc_link needs to recalculate the tx
descriptor checksum on AR9380+
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Makes it easier to clean up the ath9k_hw descriptor API
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During a reset, rx buffers are flushed after rx has been disabled. To avoid
race conditions, rx needs to stay disabled during the reset, so avoid any
calls to ath9k_hw_rxena in that case.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When starting the AP beacon timer, it assumes that the TSF has recently
been cleared. Set the SC_OP_TSF_RESET flag to ensure that this is always
the case.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The interrupt handler increases the interrupt disable refcount, so the
tasklet needs to always call ath9k_hw_enable_interrupts.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
in ath_pci_resume it seems we are not enabling LED properly, in addition
we have a PS wrapper fix for this
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
now the LED starts working for AR946/8x chipsets
Cc: "Balasubramanian, senthilkumar" <senthilb@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9003 seems to have issues sometimes with fast channel change
in 5GHz and this case is handled specifically for AR9280 by doing
a full reset. Let's do a full reset for 5GHz channles of AR9380
& for all channels of AR9280 pci chips.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the register macros to appropriate header files to be in
sync with other register definitions and also a single place
to refer everything.
Signed-off-by: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for AR946/8x chipets.
Signed-off-by: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split tx/rx gain table initval hanlding part so readability
is better and easy to manage the code.
Signed-off-by: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add initvals and register modifications required to support AR946/8x chipsets.
Signed-off-by: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Normally, the v9 firmware will be loaded if it's available. However, on
OLPC XO-1 machines, the olpc-specific firmware supports extra functionality.
This makes the libertas driver attempt to load the custom firmware first
if the machine is an OLPC machine; if that fails (or it's not an OLPC
machine), fall back to attempting to load the other firmwares.
usb8388_olpc.bin is currently found in the linux-firmware repository.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix kernel-doc warning in net/cfg80211.h:
Warning(include/net/cfg80211.h:1884): No description found for parameter 'registered'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use rt2800_config_wcid and rt2800_delete_wcid_attr to initialize the
WCID table instead of writing to the registers directly.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a STA is not known by the hw (i.e. has no WCID assigned) don't allow
aggregation since this might mess up tx status reports and we won't be
able to distinguish the reports of multiple WCID-less STAs.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows us to assign a WCID to each STA even for STAs without
crypto key.
To achieve this search for an unused WCID in the HW WCID table and
assign it to the according STA. When configuring a pairwise key for this
STA we don't need to write the MAC address and BSSIDX anymore but just
update the crypto related fields in the WCID_ATTR table.
This has two advantages:
1) Setting a new key for an already available STA (PTK rekeying) is
slightly less expensive and should improve performance in situations
where a lot of rekeying happens (e.g. a huge number of stations and/or
a small rekeying interval)
2) The TXWI now gets a WCID assigned for unencrypted frames which will
be reflected in the corresponding tx status report. This should make tx
status reports in unencrypted AP mode more reliable as we can
distinguish between multiple key-less STAs.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When sending an unencrypted frame to a STA the driver might want to pass
a suitable WCID since we don't have a key index to allow tx status
reports to get properly assigned to the correct STA.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a WCID was already assigned to a STA the key configuration
functions need to use the same WCID for configuring the keys. Hence, add
the WCID to the crypo configuration structure.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This implements a basic sta_add and sta_remove callback. Introduce a new
structure rt2x00_sta and ask mac80211 to allocate it as private part of
its ieee80211_sta. rt2x00_sta only contains the WCID for now.
The sta_add callback allows the driver to assign a WCID to a station
that is currently being added. The same wcid is also passed to the
sta_remove callback one mac80211 removes this STA.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will be used by a later patch. No functional changes.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hw.conf.channel value is not updated properly for drivers that
support HW channel switch. Since the switch is done entirely by the
driver and we don't call ieee80211_hw_config(), this value remains
untouched. This patch fixes that by setting the new channel directly in
ieee80211_chswitch_work().
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Per sec 7.1.3.5 of draft 12.0 of 802.11s, mesh frames indicate the
presence of the mesh control header in their QoS header.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to support QoS in mesh, we need to assign queue mapping only
after the next hop has been resolved, both for forwarded and locally
originated frames. Also, now that this is fixed, remove the XXX comment
in ieee80211_select_queue().
Also, V-Shy Ho reported that the queue mapping was not being applied to
the forwarded frame (fwd_skb instead of skb). Fixed that as well.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reading the TX desciptor words from coherent memory is always uncached
and potentially slow. Hence, don't read the TX descriptor prior to
writing it since we update all fields anyway.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800 devices are not capable of configuring arbitrary LED on/off
periods. The LED_CFG register fields ON_PERIOD and OFF_PERIOD are only
used by the hw when the LED mode is set to "blink upon TX".
Hence, remove the blink callback. This will result in software emulation
for LED blinking.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
