It is wrong to do --i in the for loop.
Fixes: dd02ea5a33 ("usb: gadget: mass_storage: Use static array for luns")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
IRQ_NOAUTOEN cannot be used with shared IRQs, since commit 04c848d398
("genirq: Warn when IRQ_NOAUTOEN is used with shared interrupts") and
kernel now throws a warn dump. But OMAP DWC3 driver uses this flag. As
per commit 12a7f17fac ("usb: dwc3: omap: fix race of pm runtime with
irq handler in probe") that introduced this flag, PM runtime can race
with IRQ handler when deferred probing happens due to extcon,
therefore IRQ_NOAUTOEN needs to be set so that irq is not enabled until
extcon is registered.
Remove setting of IRQ_NOAUTOEN and move the registration of
shared irq to a point after dwc3_omap_extcon_register() and
of_platform_populate(). This avoids possibility of probe deferring and
above said race condition.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
commit f54edb539c ("usb: dwc3: core: initialize ULPI before trying to
get the PHY") moved call to dwc3_core_get_phy() from dwc3_probe() to
dwc3_core_init() after dwc3_core_soft_reset(). But
dwc3_core_soft_reset() calls phy_init(), therefore dwc3_core_get_phy()
needs to be called before dwc3_core_soft_reset().
Fix this by moving call to dwc3_core_get_phy() before
dwc3_core_soft_reset().
This fixes the following abort seen on DRA7xx platforms
[ 24.769118] usb usb2: SerialNumber: xhci-hcd.1.auto
[ 24.781144] hub 2-0:1.0: USB hub found
[ 24.787836] hub 2-0:1.0: 1 port detected
[ 24.809939] Unhandled fault: imprecise external abort (0x1406) at 0x00000000
Reported-by: Carlos Hernandez <ceh@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Make the code like the rest of the kernel.
Also use inline instead of __inline__.
Link: http://lkml.kernel.org/r/a5072b74b6c293e6ec93c4900482e9d3267f15b2.1499284835.git.joe@perches.com
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here are some remaining USB fixes for 4.13-rc1. They were originally
scheduled for 4.12-final, but I didn't send them to you in time.
Because of that, they were in a separate branch from the larger USB set
of patches, so here they are in a separate pull request.
Nothing major here a all, just 3 small patches:
- some usb-serial new device ids
- xhci bugfix for some crazy AMD hardware
All of these have been in linux-next for a long time with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWV9FRg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylHxgCfTT31v4FaxH2k76qA1ZnHdXWHqyQAn3oyOE4T
uJhpp1FbFR1VNXM/jRox
=PCPm
-----END PGP SIGNATURE-----
Merge tag 'usb-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some remaining USB fixes for 4.13-rc1. They were originally
scheduled for 4.12-final, but I didn't send them to you in time.
Because of that, they were in a separate branch from the larger USB
set of patches, so here they are in a separate pull request.
Nothing major here a all, just three small patches:
- some usb-serial new device ids
- xhci bugfix for some crazy AMD hardware
All of these have been in linux-next for a long time with no reported
issues"
* tag 'usb-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
xhci: Limit USB2 port wake support for AMD Promontory hosts
USB: serial: qcserial: new Sierra Wireless EM7305 device ID
USB: serial: option: add two Longcheer device ids
Pull MFD updates from Lee Jones:
"New Drivers:
- Intel Cherry Trail Whiskey Cove PMIC
- TI LP87565 PMIC
New Device Support:
- Add support for Cannonlake to intel-lpss-pci
- Add support for Simatic IOT2000 to intel_quark_i2c_gpio
New Functionality:
- Add Regulator support (axp20x)
Fix-ups:
- Rework IRQ handling (intel_soc_pmic_bxtwc, rtsx_pcr, cros_ec)
- Remove unused/unwelcome code (ipaq-micro, wm831x-core, da9062-core)
- Provide deregistration on unbind (rn5t618)
- Rework DT code/documentation (arizona)
- Constify things (fsl-imx25-tsadc)
- MAINTAINERS updates (DA9062/61)
- Kconfig configuration adaptions (INTEL_SOC_PMIC, MFD_AXP20X_I2C)
- Switch to DMI matching (intel_quark_i2c_gpio)
- Provide an appropriate level of error checking (wm831x-{i2c,spi},
twl4030-irq, tc6393xb)
- Make use of devm_* (resource handling) calls (intel_soc_pmic_bxtwc,
stm32-timers, atmel-flexcom, cros_ec, fsl-imx25-tsadc,
exynos-lpass, palmas, qcom-spmi-pmic, smsc-ece1099,
motorola-cpcap)"
[ Skipped the last commit in that series that added eight thousand
lines of pointless repeated register definitions. - Linus ]
* tag 'mfd-next-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (38 commits)
mfd: Add LP87565 PMIC support
mfd: cros_ec: Free IRQ on exit
dt-bindings: vendor-prefixes: Add arctic to vendor prefix
mfd: da9061: Fix to remove BBAT_CONT register from chip model
mfd: da9061: Fix to remove BBAT_CONT register from chip model
mfd: axp20x-i2c: Document that this must be builtin on x86
mfd: Add Cherry Trail Whiskey Cove PMIC driver
mfd: tc6393xb: Handle return value of clk_prepare_enable
mfd: intel_quark_i2c_gpio: Add support for SIMATIC IOT2000 platform
mfd: intel_quark_i2c_gpio: Use dmi_system_id table for retrieving frequency
mfd: motorola-cpcap: Use devm_of_platform_populate()
mfd: smsc-ece: Use devm_of_platform_populate()
mfd: qcom-spmi-pmic: Use devm_of_platform_populate()
mfd: palmas: Use devm_of_platform_populate()
mfd: exynos: Use devm_of_platform_populate()
mfd: fsl-imx25: Use devm_of_platform_populate()
mfd: cros_ec: Use devm_of_platform_populate()
mfd: atmel: Use devm_of_platform_populate()
mfd: stm32-timers: Use devm_of_platform_populate()
mfd: intel_soc_pmic: Select designware i2c-bus driver
...
Pull misc compat stuff updates from Al Viro:
"This part is basically untangling various compat stuff. Compat
syscalls moved to their native counterparts, getting rid of quite a
bit of double-copying and/or set_fs() uses. A lot of field-by-field
copyin/copyout killed off.
- kernel/compat.c is much closer to containing just the
copyin/copyout of compat structs. Not all compat syscalls are gone
from it yet, but it's getting there.
- ipc/compat_mq.c killed off completely.
- block/compat_ioctl.c cleaned up; floppy compat ioctls moved to
drivers/block/floppy.c where they belong. Yes, there are several
drivers that implement some of the same ioctls. Some are m68k and
one is 32bit-only pmac. drivers/block/floppy.c is the only one in
that bunch that can be built on biarch"
* 'misc.compat' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
mqueue: move compat syscalls to native ones
usbdevfs: get rid of field-by-field copyin
compat_hdio_ioctl: get rid of set_fs()
take floppy compat ioctls to sodding floppy.c
ipmi: get rid of field-by-field __get_user()
ipmi: get COMPAT_IPMICTL_RECEIVE_MSG in sync with the native one
rt_sigtimedwait(): move compat to native
select: switch compat_{get,put}_fd_set() to compat_{get,put}_bitmap()
put_compat_rusage(): switch to copy_to_user()
sigpending(): move compat to native
getrlimit()/setrlimit(): move compat to native
times(2): move compat to native
compat_{get,put}_bitmap(): use unsafe_{get,put}_user()
fb_get_fscreeninfo(): don't bother with do_fb_ioctl()
do_sigaltstack(): lift copying to/from userland into callers
take compat_sys_old_getrlimit() to native syscall
trim __ARCH_WANT_SYS_OLD_GETRLIMIT
This development cycle resulted in a fair amount of changes in both
core and driver sides. The most significant change in ALSA core is
about PCM. Also the support of of-graph card and the new DAPM widget
for DSP are noteworthy changes in ASoC core. And there're lots of
small changes splat over the tree, as you can see in diffstat.
Below are a few highlights:
ALSA core:
- Removal of set_fs() hackery from PCM core stuff, and the code
reorganization / optimization thereafter
- Improved support of PCM ack ops, and a new ABI for improved
control/status mmap handling
- Lots of constifications in various codes
ASoC core:
- The support of of-graph card, which may work as a better generic
device for a replacement of simple-card
- New widget types intended mainly for use with DSPs
ASoC drivers:
- New drivers for Allwinner V3s SoCs
- Ensonic ES8316 codec support
- More Intel SKL and KBL works
- More device support for Intel SST Atom (mostly for cheap tablets and
2-in-1 devices)
- Support for Rockchip PDM controllers
- Support for STM32 I2S and S/PDIF controllers
- Support for ZTE AUD96P22 codecs
HD-audio:
- Support of new Realtek codecs (ALC215/ALC285/ALC289), more quirks
for HP and Dell machines
- A few more fixes for i915 component binding
Note that of-graph change may bring the conflicts with a later pull
request of devicetree, as currently found in linux-next.
-----BEGIN PGP SIGNATURE-----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=PUEh
-----END PGP SIGNATURE-----
Merge tag 'sound-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This development cycle resulted in a fair amount of changes in both
core and driver sides. The most significant change in ALSA core is
about PCM. Also the support of of-graph card and the new DAPM widget
for DSP are noteworthy changes in ASoC core. And there're lots of
small changes splat over the tree, as you can see in diffstat.
Below are a few highlights:
ALSA core:
- Removal of set_fs() hackery from PCM core stuff, and the code
reorganization / optimization thereafter
- Improved support of PCM ack ops, and a new ABI for improved
control/status mmap handling
- Lots of constifications in various codes
ASoC core:
- The support of of-graph card, which may work as a better generic
device for a replacement of simple-card
- New widget types intended mainly for use with DSPs
ASoC drivers:
- New drivers for Allwinner V3s SoCs
- Ensonic ES8316 codec support
- More Intel SKL and KBL works
- More device support for Intel SST Atom (mostly for cheap tablets
and 2-in-1 devices)
- Support for Rockchip PDM controllers
- Support for STM32 I2S and S/PDIF controllers
- Support for ZTE AUD96P22 codecs
HD-audio:
- Support of new Realtek codecs (ALC215/ALC285/ALC289), more quirks
for HP and Dell machines
- A few more fixes for i915 component binding"
* tag 'sound-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (418 commits)
ALSA: hda - Fix unbalance of i915 module refcount
ASoC: Intel: Skylake: Remove driver debugfs exit
ASoC: Intel: Skylake: explicitly add the headers sst-dsp.h
ALSA: hda/realtek - Remove GPIO_MASK
ALSA: hda/realtek - Fix typo of pincfg for Dell quirk
ALSA: pcm: add a documentation for tracepoints
ALSA: atmel: ac97c: fix error return code in atmel_ac97c_probe()
ALSA: x86: fix error return code in hdmi_lpe_audio_probe()
ASoC: Intel: Skylake: Add support to read firmware registers
ASoC: Intel: Skylake: Add sram address to sst_addr structure
ASoC: Intel: Skylake: Debugfs facility to dump module config
ASoC: Intel: Skylake: Add debugfs support
ASoC: fix semicolon.cocci warnings
ASoC: rt5645: Add quirk override by module option
ASoC: rsnd: make arrays path and cmd_case static const
ASoC: audio-graph-card: add widgets and routing for external amplifier support
ASoC: audio-graph-card: update bindings for amplifier support
ASoC: rt5665: calibration should be done before jack detection
ASoC: rsnd: constify dev_pm_ops structures.
ASoC: nau8825: change crosstalk-bypass property to bool type
...
Pull networking updates from David Miller:
"Reasonably busy this cycle, but perhaps not as busy as in the 4.12
merge window:
1) Several optimizations for UDP processing under high load from
Paolo Abeni.
2) Support pacing internally in TCP when using the sch_fq packet
scheduler for this is not practical. From Eric Dumazet.
3) Support mutliple filter chains per qdisc, from Jiri Pirko.
4) Move to 1ms TCP timestamp clock, from Eric Dumazet.
5) Add batch dequeueing to vhost_net, from Jason Wang.
6) Flesh out more completely SCTP checksum offload support, from
Davide Caratti.
7) More plumbing of extended netlink ACKs, from David Ahern, Pablo
Neira Ayuso, and Matthias Schiffer.
8) Add devlink support to nfp driver, from Simon Horman.
9) Add RTM_F_FIB_MATCH flag to RTM_GETROUTE queries, from Roopa
Prabhu.
10) Add stack depth tracking to BPF verifier and use this information
in the various eBPF JITs. From Alexei Starovoitov.
11) Support XDP on qed device VFs, from Yuval Mintz.
12) Introduce BPF PROG ID for better introspection of installed BPF
programs. From Martin KaFai Lau.
13) Add bpf_set_hash helper for TC bpf programs, from Daniel Borkmann.
14) For loads, allow narrower accesses in bpf verifier checking, from
Yonghong Song.
15) Support MIPS in the BPF selftests and samples infrastructure, the
MIPS eBPF JIT will be merged in via the MIPS GIT tree. From David
Daney.
16) Support kernel based TLS, from Dave Watson and others.
17) Remove completely DST garbage collection, from Wei Wang.
18) Allow installing TCP MD5 rules using prefixes, from Ivan
Delalande.
19) Add XDP support to Intel i40e driver, from Björn Töpel
20) Add support for TC flower offload in nfp driver, from Simon
Horman, Pieter Jansen van Vuuren, Benjamin LaHaise, Jakub
Kicinski, and Bert van Leeuwen.
21) IPSEC offloading support in mlx5, from Ilan Tayari.
22) Add HW PTP support to macb driver, from Rafal Ozieblo.
23) Networking refcount_t conversions, From Elena Reshetova.
24) Add sock_ops support to BPF, from Lawrence Brako. This is useful
for tuning the TCP sockopt settings of a group of applications,
currently via CGROUPs"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1899 commits)
net: phy: dp83867: add workaround for incorrect RX_CTRL pin strap
dt-bindings: phy: dp83867: provide a workaround for incorrect RX_CTRL pin strap
cxgb4: Support for get_ts_info ethtool method
cxgb4: Add PTP Hardware Clock (PHC) support
cxgb4: time stamping interface for PTP
nfp: default to chained metadata prepend format
nfp: remove legacy MAC address lookup
nfp: improve order of interfaces in breakout mode
net: macb: remove extraneous return when MACB_EXT_DESC is defined
bpf: add missing break in for the TCP_BPF_SNDCWND_CLAMP case
bpf: fix return in load_bpf_file
mpls: fix rtm policy in mpls_getroute
net, ax25: convert ax25_cb.refcount from atomic_t to refcount_t
net, ax25: convert ax25_route.refcount from atomic_t to refcount_t
net, ax25: convert ax25_uid_assoc.refcount from atomic_t to refcount_t
net, sctp: convert sctp_ep_common.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_transport.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_chunk.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_datamsg.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_auth_bytes.refcnt from atomic_t to refcount_t
...
- Rework suspend-to-idle to allow it to take wakeup events signaled
by the EC into account on ACPI-based platforms in order to properly
support power button wakeup from suspend-to-idle on recent Dell
laptops (Rafael Wysocki).
That includes the core suspend-to-idle code rework, support for
the Low Power S0 _DSM interface, and support for the ACPI INT0002
Virtual GPIO device from Hans de Goede (required for USB keyboard
wakeup from suspend-to-idle to work on some machines).
- Stop trying to export the current CPU frequency via /proc/cpuinfo
on x86 as that is inaccurate and confusing (Len Brown).
- Rework the way in which the current CPU frequency is exported by
the kernel (over the cpufreq sysfs interface) on x86 systems with
the APERF and MPERF registers by always using values read from
these registers, when available, to compute the current frequency
regardless of which cpufreq driver is in use (Len Brown).
- Rework the PCI/ACPI device wakeup infrastructure to remove the
questionable and artificial distinction between "devices that
can wake up the system from sleep states" and "devices that can
generate wakeup signals in the working state" from it, which
allows the code to be simplified quite a bit (Rafael Wysocki).
- Fix the wakeup IRQ framework by making it use SRCU instead of
RCU which doesn't allow sleeping in the read-side critical
sections, but which in turn is expected to be allowed by the
IRQ bus locking infrastructure (Thomas Gleixner).
- Modify some computations in the intel_pstate driver to avoid
rounding errors resulting from them (Srinivas Pandruvada).
- Reduce the overhead of the intel_pstate driver in the HWP
(hardware-managed P-states) mode and when the "performance"
P-state selection algorithm is in use by making it avoid
registering scheduler callbacks in those cases (Len Brown).
- Rework the energy_performance_preference sysfs knob in
intel_pstate by changing the values that correspond to
different symbolic hint names used by it (Len Brown).
- Make it possible to use more than one cpuidle driver at the same
time on ARM (Daniel Lezcano).
- Make it possible to prevent the cpuidle menu governor from using
the 0 state by disabling it via sysfs (Nicholas Piggin).
- Add support for FFH (Fixed Functional Hardware) MWAIT in ACPI C1
on AMD systems (Yazen Ghannam).
- Make the CPPC cpufreq driver take the lowest nonlinear performance
information into account (Prashanth Prakash).
- Add support for hi3660 to the cpufreq-dt driver, fix the
imx6q driver and clean up the sfi, exynos5440 and intel_pstate
drivers (Colin Ian King, Krzysztof Kozlowski, Octavian Purdila,
Rafael Wysocki, Tao Wang).
- Fix a few minor issues in the generic power domains (genpd)
framework and clean it up somewhat (Krzysztof Kozlowski,
Mikko Perttunen, Viresh Kumar).
- Fix a couple of minor issues in the operating performance points
(OPP) framework and clean it up somewhat (Viresh Kumar).
- Fix a CONFIG dependency in the hibernation core and clean it up
slightly (Balbir Singh, Arvind Yadav, BaoJun Luo).
- Add rk3228 support to the rockchip-io adaptive voltage scaling
(AVS) driver (David Wu).
- Fix an incorrect bit shift operation in the RAPL power capping
driver (Adam Lessnau).
- Add support for the EPP field in the HWP (hardware managed
P-states) control register, HWP.EPP, to the x86_energy_perf_policy
tool and update msr-index.h with HWP.EPP values (Len Brown).
- Fix some minor issues in the turbostat tool (Len Brown).
- Add support for AMD family 0x17 CPUs to the cpupower tool and fix
a minor issue in it (Sherry Hurwitz).
- Assorted cleanups, mostly related to the constification of some
data structures (Arvind Yadav, Joe Perches, Kees Cook, Krzysztof
Kozlowski).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Wsph
-----END PGP SIGNATURE-----
Merge tag 'pm-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"The big ticket items here are the rework of suspend-to-idle in order
to add proper support for power button wakeup from it on recent Dell
laptops and the rework of interfaces exporting the current CPU
frequency on x86.
In addition to that, support for a few new pieces of hardware is
added, the PCI/ACPI device wakeup infrastructure is simplified
significantly and the wakeup IRQ framework is fixed to unbreak the IRQ
bus locking infrastructure.
Also, there are some functional improvements for intel_pstate, tools
updates and small fixes and cleanups all over.
Specifics:
- Rework suspend-to-idle to allow it to take wakeup events signaled
by the EC into account on ACPI-based platforms in order to properly
support power button wakeup from suspend-to-idle on recent Dell
laptops (Rafael Wysocki).
That includes the core suspend-to-idle code rework, support for the
Low Power S0 _DSM interface, and support for the ACPI INT0002
Virtual GPIO device from Hans de Goede (required for USB keyboard
wakeup from suspend-to-idle to work on some machines).
- Stop trying to export the current CPU frequency via /proc/cpuinfo
on x86 as that is inaccurate and confusing (Len Brown).
- Rework the way in which the current CPU frequency is exported by
the kernel (over the cpufreq sysfs interface) on x86 systems with
the APERF and MPERF registers by always using values read from
these registers, when available, to compute the current frequency
regardless of which cpufreq driver is in use (Len Brown).
- Rework the PCI/ACPI device wakeup infrastructure to remove the
questionable and artificial distinction between "devices that can
wake up the system from sleep states" and "devices that can
generate wakeup signals in the working state" from it, which allows
the code to be simplified quite a bit (Rafael Wysocki).
- Fix the wakeup IRQ framework by making it use SRCU instead of RCU
which doesn't allow sleeping in the read-side critical sections,
but which in turn is expected to be allowed by the IRQ bus locking
infrastructure (Thomas Gleixner).
- Modify some computations in the intel_pstate driver to avoid
rounding errors resulting from them (Srinivas Pandruvada).
- Reduce the overhead of the intel_pstate driver in the HWP
(hardware-managed P-states) mode and when the "performance" P-state
selection algorithm is in use by making it avoid registering
scheduler callbacks in those cases (Len Brown).
- Rework the energy_performance_preference sysfs knob in intel_pstate
by changing the values that correspond to different symbolic hint
names used by it (Len Brown).
- Make it possible to use more than one cpuidle driver at the same
time on ARM (Daniel Lezcano).
- Make it possible to prevent the cpuidle menu governor from using
the 0 state by disabling it via sysfs (Nicholas Piggin).
- Add support for FFH (Fixed Functional Hardware) MWAIT in ACPI C1 on
AMD systems (Yazen Ghannam).
- Make the CPPC cpufreq driver take the lowest nonlinear performance
information into account (Prashanth Prakash).
- Add support for hi3660 to the cpufreq-dt driver, fix the imx6q
driver and clean up the sfi, exynos5440 and intel_pstate drivers
(Colin Ian King, Krzysztof Kozlowski, Octavian Purdila, Rafael
Wysocki, Tao Wang).
- Fix a few minor issues in the generic power domains (genpd)
framework and clean it up somewhat (Krzysztof Kozlowski, Mikko
Perttunen, Viresh Kumar).
- Fix a couple of minor issues in the operating performance points
(OPP) framework and clean it up somewhat (Viresh Kumar).
- Fix a CONFIG dependency in the hibernation core and clean it up
slightly (Balbir Singh, Arvind Yadav, BaoJun Luo).
- Add rk3228 support to the rockchip-io adaptive voltage scaling
(AVS) driver (David Wu).
- Fix an incorrect bit shift operation in the RAPL power capping
driver (Adam Lessnau).
- Add support for the EPP field in the HWP (hardware managed
P-states) control register, HWP.EPP, to the x86_energy_perf_policy
tool and update msr-index.h with HWP.EPP values (Len Brown).
- Fix some minor issues in the turbostat tool (Len Brown).
- Add support for AMD family 0x17 CPUs to the cpupower tool and fix a
minor issue in it (Sherry Hurwitz).
- Assorted cleanups, mostly related to the constification of some
data structures (Arvind Yadav, Joe Perches, Kees Cook, Krzysztof
Kozlowski)"
* tag 'pm-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (69 commits)
cpufreq: Update scaling_cur_freq documentation
cpufreq: intel_pstate: Clean up after performance governor changes
PM: hibernate: constify attribute_group structures.
cpuidle: menu: allow state 0 to be disabled
intel_idle: Use more common logging style
PM / Domains: Fix missing default_power_down_ok comment
PM / Domains: Fix unsafe iteration over modified list of domains
PM / Domains: Fix unsafe iteration over modified list of domain providers
PM / Domains: Fix unsafe iteration over modified list of device links
PM / Domains: Handle safely genpd_syscore_switch() call on non-genpd device
PM / Domains: Call driver's noirq callbacks
PM / core: Drop run_wake flag from struct dev_pm_info
PCI / PM: Simplify device wakeup settings code
PCI / PM: Drop pme_interrupt flag from struct pci_dev
ACPI / PM: Consolidate device wakeup settings code
ACPI / PM: Drop run_wake from struct acpi_device_wakeup_flags
PM / QoS: constify *_attribute_group.
PM / AVS: rockchip-io: add io selectors and supplies for rk3228
powercap/RAPL: prevent overridding bits outside of the mask
PM / sysfs: Constify attribute groups
...
Here is the big driver core update for 4.13-rc1.
The large majority of this is a lot of cleanup of old fields in the
driver core structures and their remaining usages in random drivers.
All of those fixes have been reviewed by the various subsystem
maintainers. There's also some small firmware updates in here, a new
kobject uevent api interface that makes userspace interaction easier,
and a few other minor things.
All of these have been in linux-next for a long while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpX4A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymobgCfd0d13IfpZoq1N41wc6z2Z0xD7cwAnRMeH1/p
kEeISGpHPYP9f8PBh9FO
=Hfqt
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big driver core update for 4.13-rc1.
The large majority of this is a lot of cleanup of old fields in the
driver core structures and their remaining usages in random drivers.
All of those fixes have been reviewed by the various subsystem
maintainers. There's also some small firmware updates in here, a new
kobject uevent api interface that makes userspace interaction easier,
and a few other minor things.
All of these have been in linux-next for a long while with no reported
issues"
* tag 'driver-core-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (56 commits)
arm: mach-rpc: ecard: fix build error
zram: convert remaining CLASS_ATTR() to CLASS_ATTR_RO()
driver-core: remove struct bus_type.dev_attrs
powerpc: vio_cmo: use dev_groups and not dev_attrs for bus_type
powerpc: vio: use dev_groups and not dev_attrs for bus_type
USB: usbip: convert to use DRIVER_ATTR_RW
s390: drivers: convert to use DRIVER_ATTR_RO/WO
platform: thinkpad_acpi: convert to use DRIVER_ATTR_RO/RW
pcmcia: ds: convert to use DRIVER_ATTR_RO
wireless: ipw2x00: convert to use DRIVER_ATTR_RW
net: ehea: convert to use DRIVER_ATTR_RO
net: caif: convert to use DRIVER_ATTR_RO
TTY: hvc: convert to use DRIVER_ATTR_RW
PCI: pci-driver: convert to use DRIVER_ATTR_WO
IB: nes: convert to use DRIVER_ATTR_RW
HID: hid-core: convert to use DRIVER_ATTR_RO and drv_groups
arm: ecard: fix dev_groups patch typo
tty: serdev: use dev_groups and not dev_attrs for bus_type
sparc: vio: use dev_groups and not dev_attrs for bus_type
hid: intel-ish-hid: use dev_groups and not dev_attrs for bus_type
...
Here is the large tty/serial patchset for 4.13-rc1.
A lot of tty and serial driver updates are in here, along with some
fixups for some __get/put_user usages that were reported. Nothing huge,
just lots of development by a number of different developers, full
details in the shortlog.
All of these have been in linux-next for a while. There will be a merge
issue with the arm-soc tree in the include/linux/platform_data/atmel.h
file. Stephen has sent out a fixup for it, so it shouldn't be that
difficult to merge.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpZ9w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylkTgCfV2HhbxIph/aEL1nJmwW64oCXFrMAoK59ZH65
tBZIosv0d91K1A+mObBT
=adPL
-----END PGP SIGNATURE-----
Merge tag 'tty-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the large tty/serial patchset for 4.13-rc1.
A lot of tty and serial driver updates are in here, along with some
fixups for some __get/put_user usages that were reported. Nothing
huge, just lots of development by a number of different developers,
full details in the shortlog.
All of these have been in linux-next for a while"
* tag 'tty-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (71 commits)
tty: serial: lpuart: add a more accurate baud rate calculation method
tty: serial: lpuart: add earlycon support for imx7ulp
tty: serial: lpuart: add imx7ulp support
dt-bindings: serial: fsl-lpuart: add i.MX7ULP support
tty: serial: lpuart: add little endian 32 bit register support
tty: serial: lpuart: refactor lpuart32_{read|write} prototype
tty: serial: lpuart: introduce lpuart_soc_data to represent SoC property
serial: imx-serial - move DMA buffer configuration to DT
serial: imx: Enable RTSD only when needed
serial: imx: Remove unused members from imx_port struct
serial: 8250: 8250_omap: Fix race b/w dma completion and RX timeout
serial: 8250: Fix THRE flag usage for CAP_MINI
tty/serial: meson_uart: update to stable bindings
dt-bindings: serial: Add bindings for the Amlogic Meson UARTs
serial: Delete dead code for CIR serial ports
serial: sirf: make of_device_ids const
serial/mpsc: switch to dma_alloc_attrs
tty: serial: Add Actions Semi Owl UART earlycon
dt-bindings: serial: Document Actions Semi Owl UARTs
tty/serial: atmel: make the driver DT only
...
Here is the big patchset of USB and PHY driver updates for 4.13-rc1.
On the PHY side, they decided to move files around to "make things
easier" in their tree. Hopefully that wasn't a mistake, but in
linux-next testing, we haven't had any reported problems.
There's the usual set of gadget and xhci and musb updates in here as
well, along with a number of smaller updates for a raft of different USB
drivers. Full details in the shortlog, nothing really major.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpavQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymJrgCgp8Pso8bs+bnIknUSQFSguWd3wM0AnA8X3NHf
lrdCuqw+2oxGOQrecacz
=5L4Q
-----END PGP SIGNATURE-----
Merge tag 'usb-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big patchset of USB and PHY driver updates for 4.13-rc1.
On the PHY side, they decided to move files around to "make things
easier" in their tree. Hopefully that wasn't a mistake, but in
linux-next testing, we haven't had any reported problems.
There's the usual set of gadget and xhci and musb updates in here as
well, along with a number of smaller updates for a raft of different
USB drivers. Full details in the shortlog, nothing really major.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (173 commits)
Add USB quirk for HVR-950q to avoid intermittent device resets
USB hub_probe: rework ugly goto-into-compound-statement
usb: host: ohci-pxa27x: Handle return value of clk_prepare_enable
USB: serial: cp210x: add ID for CEL EM3588 USB ZigBee stick
usbip: Fix uninitialized variable bug in vhci
usb: core: read USB ports from DT in the usbport LED trigger driver
dt-bindings: leds: document new trigger-sources property
usb: typec: ucsi: Add ACPI driver
usb: typec: Add support for UCSI interface
usb: musb: compress return logic into one line
USB: serial: propagate late probe errors
USB: serial: refactor port endpoint setup
usb: musb: tusb6010_omap: Convert to DMAengine API
ARM: OMAP2+: DMA: Add slave map entries for 24xx external request lines
usb: musb: tusb6010: Handle DMA TX completion in DMA callback as well
usb: musb: tusb6010_omap: Allocate DMA channels upfront
usb: musb: tusb6010_omap: Create new struct for DMA data/parameters
usb: musb: tusb6010_omap: Use one musb_ep_select call in tusb_omap_dma_program
usb: musb: tusb6010: Add MUSB_G_NO_SKB_RESERVE to quirks
usb: musb: Add quirk to avoid skb reserve in gadget mode
...
The big news with this release is the of-graph card, this provides a
replacement for simple-card that is much more flexibile and scalable,
allowing many more systems to use a generic sound card than was possible
before:
- The of-graph card, finally merged after a long and dedicated effort
by Morimoto-san.
- New widget types intended mainly for use with DSPs.
- New drivers for Allwinner V3s SoCs, Ensonic ES8316, several classes
of x86 machine, Rockchip PDM controllers, STM32 I2S and S/PDIF
controllers and ZTE AUD96P22 CODECs.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAllaa7wTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0MhRB/0cIuUi/SmMSGz7cNKdDDArdpxHUV0U
dJb6qqhXCKeDQcx/34b1m+BnZpeT9au4Nt8HxOlLRbumcnuesYqfeBeZvuJhsC4I
q3e8e+idQlOp3+WM+snUXhWM4P/UsA9H4BaV1jvYSQW/C9WhfuLxsOraRiebLH7u
WJkmfeVjpzHHWzfDtpWJLHVroRLLMbOaz0e0Pw8/R1dfof0u27zKknqHOUcwRg0N
4+IWvKn3p59VE6eM6QUmruMZZCCfn2Hv5RygWf3LaHVlhA28BZi0dyMMSSSzVG6o
Im1Wm5z0dmmTfQKdNDU3PPBEKG6amTqF+2uuXOsq1I7vuiT+akHZbgWW
=F5BP
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v4.13
The big news with this release is the of-graph card, this provides a
replacement for simple-card that is much more flexibile and scalable,
allowing many more systems to use a generic sound card than was possible
before:
- The of-graph card, finally merged after a long and dedicated effort
by Morimoto-san.
- New widget types intended mainly for use with DSPs.
- New drivers for Allwinner V3s SoCs, Ensonic ES8316, several classes
of x86 machine, Rockchip PDM controllers, STM32 I2S and S/PDIF
controllers and ZTE AUD96P22 CODECs.
- introduce the new uuid_t/guid_t types that are going to replace
the somewhat confusing uuid_be/uuid_le types and make the terminology
fit the various specs, as well as the userspace libuuid library.
(me, based on a previous version from Amir)
- consolidated generic uuid/guid helper functions lifted from XFS
and libnvdimm (Amir and me)
- conversions to the new types and helpers (Amir, Andy and me)
-----BEGIN PGP SIGNATURE-----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=J/4P
-----END PGP SIGNATURE-----
Merge tag 'uuid-for-4.13' of git://git.infradead.org/users/hch/uuid
Pull uuid subsystem from Christoph Hellwig:
"This is the new uuid subsystem, in which Amir, Andy and I have started
consolidating our uuid/guid helpers and improving the types used for
them. Note that various other subsystems have pulled in this tree, so
I'd like it to go in early.
UUID/GUID summary:
- introduce the new uuid_t/guid_t types that are going to replace the
somewhat confusing uuid_be/uuid_le types and make the terminology
fit the various specs, as well as the userspace libuuid library.
(me, based on a previous version from Amir)
- consolidated generic uuid/guid helper functions lifted from XFS and
libnvdimm (Amir and me)
- conversions to the new types and helpers (Amir, Andy and me)"
* tag 'uuid-for-4.13' of git://git.infradead.org/users/hch/uuid: (34 commits)
ACPI: hns_dsaf_acpi_dsm_guid can be static
mmc: sdhci-pci: make guid intel_dsm_guid static
uuid: Take const on input of uuid_is_null() and guid_is_null()
thermal: int340x_thermal: fix compile after the UUID API switch
thermal: int340x_thermal: Switch to use new generic UUID API
acpi: always include uuid.h
ACPI: Switch to use generic guid_t in acpi_evaluate_dsm()
ACPI / extlog: Switch to use new generic UUID API
ACPI / bus: Switch to use new generic UUID API
ACPI / APEI: Switch to use new generic UUID API
acpi, nfit: Switch to use new generic UUID API
MAINTAINERS: add uuid entry
tmpfs: generate random sb->s_uuid
scsi_debug: switch to uuid_t
nvme: switch to uuid_t
sysctl: switch to use uuid_t
partitions/ldm: switch to use uuid_t
overlayfs: use uuid_t instead of uuid_be
fs: switch ->s_uuid to uuid_t
ima/policy: switch to use uuid_t
...
* acpi-pm:
PM / core: Drop run_wake flag from struct dev_pm_info
PCI / PM: Simplify device wakeup settings code
PCI / PM: Drop pme_interrupt flag from struct pci_dev
ACPI / PM: Consolidate device wakeup settings code
ACPI / PM: Drop run_wake from struct acpi_device_wakeup_flags
ACPI / sleep: EC-based wakeup from suspend-to-idle on recent systems
platform: x86: intel-hid: Wake up the system from suspend-to-idle
platform: x86: intel-vbtn: Wake up the system from suspend-to-idle
ACPI / PM: Ignore spurious SCI wakeups from suspend-to-idle
platform/x86: Add driver for ACPI INT0002 Virtual GPIO device
PCI / PM: Restore PME Enable if skipping wakeup setup
PM / sleep: Print timing information if debug is enabled
ACPI / PM: Clean up device wakeup enable/disable code
ACPI / PM: Change log level of wakeup-related message
USB / PCI / PM: Allow the PCI core to do the resume cleanup
ACPI / PM: Run wakeup notify handlers synchronously
Conflicts:
drivers/base/power/main.c
The USB core and sysfs will attempt to enumerate certain parameters
which are unsupported by the au0828 - causing inconsistent behavior
and sometimes causing the chip to reset. Avoid making these calls.
This problem manifested as intermittent cases where the au8522 would
be reset on analog video startup, in particular when starting up ALSA
audio streaming in parallel - the sysfs entries created by
snd-usb-audio on streaming startup would result in unsupported control
messages being sent during tuning which would put the chip into an
unknown state.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rework smelling code (goto inside compound statement). Perhaps this is
legacy. Anyway such code is not appropriate for Linux kernel.
Signed-off-by: Eugene Korenevsky <ekorenevsky@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added the USB serial device ID for the CEL ZigBee EM3588
radio stick.
Signed-off-by: Jeremie Rapin <rapinj@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 4.13, including support for
manipulating the modem-control signals of qcserial devices, propagation
of errnos after late probe errors from usb-serial core, and a couple of
clean ups.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=1HgT
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.13-rc1
Here are the USB-serial updates for 4.13, including support for
manipulating the modem-control signals of qcserial devices, propagation
of errnos after late probe errors from usb-serial core, and a couple of
clean ups.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
The run_wake flag in struct dev_pm_info is used to indicate whether
or not the device is capable of generating remote wakeup signals at
run time (or in the system working state), but the distinction
between runtime remote wakeup and system wakeup signaling has always
been rather artificial. The only practical reason for it to exist
at the core level was that ACPI and PCI treated those two cases
differently, but that's not the case any more after recent changes.
For this reason, get rid of the run_wake flag and, when applicable,
use device_set_wakeup_capable() and device_can_wakeup() instead of
device_set_run_wake() and device_run_wake(), respectively.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The patch 03cd00d538: "usbip: vhci-hcd: Set the vhci structure up
to work" introduced a bug which uses a vairable without initialization
in error handling code. Fix it.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yuyang Du <yuyang.du@intel.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This uses DT info to read relation description of LEDs and USB ports. If
DT has properly described LEDs, trigger will know when to turn them on.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UCSI - USB Type-C Connector System Software Interface - is a
specification that defines set of registers and data
structures for controlling the USB Type-C ports. It's
designed for systems where an embedded controller (EC) is in
charge of the USB Type-C PHY or USB Power Delivery
controller. It is designed for systems with EC, but it is
not limited to them, and for example some USB Power Delivery
controllers will use it as their direct control interface.
With UCSI the EC (or USB PD controller) acts as the port
manager, implementing all USB Type-C and Power Delivery state
machines. The OS can use the interfaces for reading the
status of the ports and controlling basic operations like
role swapping.
The UCSI specification highlights the fact that it does not
define the interface method (PCI/I2C/ACPI/etc.).
Therefore the driver is implemented as library and every
supported interface method needs its own driver. Driver for
ACPI is provided in separate patch following this one.
The initial driver includes support for all required
features from UCSI specification version 1.0 (getting
connector capabilities and status, and support for power and
data role swapping), but none of the optional UCSI features
(alternate modes, power source capabilities, and cable
capabilities).
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify return logic to avoid unnecessary variable assignment.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZSdzXAAoJEEhZKYFQ1nG7M1YH/0tSpERwjAaL8xmKjm1KDO9v
EeeTC/P7nkv1iWRdMGZuun8cOivuTD4aC/IuXh6G40FkgUUMZI8qayt+JnS6eiv/
fVbX1L6lP8UnP9C8HHQcANCVlOHysPlbG3hdfpAVjtz56sqdK7NGFakdhHqBerx9
xcD40glwLUpt3jrZfcHPepF9WMn/3eA0GsTXyydHuL/D+jejCUu4kVPICdfOm7Vr
k+E0oilsjfYSxA4NRaqjd5CDpAiPPKQ/g37DIfG13A9bBjvDSQbky4Y69ibVWLqv
sGGCnLeFGx3L798GKeV6bDsKU8NEYF93pnFlQ5FBY5PjYU3mudEXAB/fpVBGagA=
=KEw/
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
One patch to improve error handling at chipidea core
Two entries being added at the same time to the IFLA
policy table, whilst parallel bug fixes to decnet
routing dst handling overlapping with the dst gc removal
in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate errnos for late probe errors (e.g. -ENOMEM on allocation
failures) instead of always returning -EIO.
Note that some drivers are currently returning -ENODEV from their attach
callbacks when a device is not supported, but this has also been mapped
to -EIO.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make the probe callback more readable by refactoring the port
endpoint-resource setup by adding four helper functions.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
With the port_window support in DMAengine and the sDMA driver we can
convert the driver to DMAengine.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handle the DMA TX in a similar way as we do for the RX: in the DMA
completion callback.
Since we are no longer using DMA completion interrupt for the TX we can as
wall keep these interrupts disabled, but keep the handler for debug
purposes.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of requesting the DMA channel in tusb_omap_dma_allocate() do it
when the controller is created and in runtime work from the DMA channel
pool.
This change is needed for the DMAengine conversion of the driver since the
tusb_omap_dma_allocate() is called in interrupt context which might lead
to lock within the DMAengine API when requesting channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the DMA we have ch (channel), dmareq and sync_dev parameters both
within the tusb_omap_dma_ch and tusb_omap_dma struct.
By creating a common struct the code can be simplified when selecting
between the shared or multichannel DMA parameters.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having one musb_ep_select() instead the two calls in if/else is the same
thing, but makes the code a bit simpler to follow.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using the g_ncm for networking this flag will make sure that the
buffer is aligned to 32bit so the DMA can be used to offload the data
movement.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For tusb6010 the DMA functionality only possible if the buffer is 32bit
aligned (SYNC access to FIFO) since with ASYNC access the TX/RX offset
registers will corrupt eventually.
The MUSB_G_NO_SKB_RESERVE will set the quirk_avoids_skb_reserve flag in
usb_gadget struct to provide correctly aligned buffer.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If dma_request_slave_channel() failed to return a channel,
then the driver will print an error and request to defer probe,
regardless of the cause of the failure.
Defer if the DMA is not ready yet otherwise print an error.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This time around we have a total of 57 non-merge commits. A list of
most important changes follows:
- Improvements to dwc3 tracing interface
- Initial dual-role support for dwc3
- Improvements to how we handle DMA resources in dwc3
- A new f_uac1 implementation which much more flexible
- Removal of AVR32 bits
- Improvements to f_mass_storage driver
-----BEGIN PGP SIGNATURE-----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=v6a5
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing
Felipe writes:
usb: changes for v4.13 merge window
This time around we have a total of 57 non-merge commits. A list of
most important changes follows:
- Improvements to dwc3 tracing interface
- Initial dual-role support for dwc3
- Improvements to how we handle DMA resources in dwc3
- A new f_uac1 implementation which much more flexible
- Removal of AVR32 bits
- Improvements to f_mass_storage driver
For AMD Promontory xHCI host, although you can disable USB 2.0 ports in
BIOS settings, those ports will be enabled anyway after you remove a
device on that port and re-plug it in again. It's a known limitation of
the chip. As a workaround we can clear the PORT_WAKE_BITS.
This will disable wake on connect, disconnect and overcurrent on
AMD Promontory USB2 ports
[checkpatch cleanup and commit message reword -Mathias]
Cc: <stable@vger.kernel.org>
Cc: Tsai Nicholas <nicholas.tsai@amd.com>
Signed-off-by: Jiahau Chang <Lars_Chang@asmedia.com.tw>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some new modem device ids.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEHszNKQClByu0A+9RQQ3kT97htJUFAllD0cgRHGpvaGFuQGtl
cm5lbC5vcmcACgkQQQ3kT97htJVdNhAAlSIY685P3pjWQNY2ddxFe+DoEY67Nt1P
HLvA/4+N/mOGfsfrid6yl5U9/WXWXgogErgsRUnHKrngsYUXCZ1Vz376CzASuepN
UWY9C4CNMhUPltsGNiB30plDHCtCzEzhA2AiLhE7N/E6UgUHStwL7DdYJI7NAgHG
EPFFmBNU+SnOVKRUTjRwVjRqiCuFfnW78EtVeIb5xZacmfIbEHryqJy0/yBBVLhT
NmaJFi3lSz+ShlMS7V9JCwWGHM7y8uBANbXg7601XX9Z4PYJZjlOudZguk217dlM
DbGGlOIqj/ATD7WO0K+IQAnmQeJ6rQqDg6GqX8H283otAuCEgOXXGUlOKqws7zU7
oqnERRRMUeXBW3UzueCH+yhR6kh9DA2pAJ2J+Hf9mab2G7wGOKu2jI6x+/L3QjL3
4fKIrbAnII/9ksXhUStz5uPtgbn4gi1RiBlT+NigpbBEc6tijGeD/ASCnSWqsw7E
6YzMRNCrv7oixcIGIq0lRaRhkRP2PYE5QsYD3/IH83Eh/VQk+tc/R/4sNfSqRw9w
cUBgpYmtq8ByeImDBQazTGmGmxIKoEW+cFw5hwDe/uaJgKk1BY+zs+z5mD+r3917
l1VnG0Wa7dNY34BbLX2JKmZgNP+jrXCRt1HfCIDFxBzJ0rbeUxrhyueOmiqnqSpS
BN/3V64QT8c=
=rha4
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.12-rc6
Here are some new modem device ids.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
Whishkey cove PMIC has support to mask/unmask interrupts at two levels.
At first level we can mask/unmask interrupt domains like TMU, GPIO, ADC,
CHGR, BCU THERMAL and PWRBTN and at second level, it provides facility
to mask/unmask individual interrupts belong each of this domain. For
example, in case of TMU, at first level we have TMU interrupt domain,
and at second level we have two interrupts, wake alarm, system alarm that
belong to the TMU interrupt domain.
Currently, in this driver all first level IRQs are registered as part of
IRQ chip(bxtwc_regmap_irq_chip). By default, after you register the IRQ
chip from your driver, all IRQs in that chip will masked and can only be
enabled if that IRQ is requested using request_irq() call. This is the
default Linux IRQ behavior model. And whenever a dependent device that
belongs to PMIC requests only the second level IRQ and not explicitly
unmask the first level IRQ, then in essence the second level IRQ will
still be disabled. For example, if TMU device driver request wake_alarm
IRQ and not explicitly unmask TMU level 1 IRQ then according to the default
Linux IRQ model, wake_alarm IRQ will still be disabled. So the proper
solution to fix this issue is to use the chained IRQ chip concept. We
should chain all the second level chip IRQs to the corresponding first
level IRQ. To do this, we need to create separate IRQ chips for every
group of second level IRQs.
In case of TMU, when adding second level IRQ chip, instead of using PMIC
IRQ we should use the corresponding first level IRQ. So the following
code will change from
ret = regmap_add_irq_chip(pmic->regmap, pmic->irq, ...)
to,
virq = regmap_irq_get_virq(&pmic->irq_chip_data, BXTWC_TMU_LVL1_IRQ);
ret = regmap_add_irq_chip(pmic->regmap, virq, ...)
In case of Whiskey Cove Type-C driver, Since USBC IRQ is moved under
charger level2 IRQ chip. We should use charger IRQ chip(irq_chip_data_chgr)
to get the USBC virtual IRQ number.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Revieved-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds a new function 'f_uac1'
(f_uac1 with virtual "ALSA card") that
uses recently created u_audio API. Comparing
to legacy f_uac1 function implementation it
doesn't require any real Audio codec to be
present on the device. In f_uac1 audio
streams are simply sinked to and sourced
from a virtual ALSA sound card created
using u_audio API.
Legacy f_uac1 approach is to write audio
samples directly to existing ALSA sound
card
f_uac1 approach is more generic/flexible
one - create an ALSA sound card that
represents USB Audio function and allows to
be used by userspace application that
may choose to do whatever it wants with the
data received from the USB Host and choose
to provide whatever it wants as audio data
to the USB Host.
f_uac1 also has capture support (gadget->host)
thanks to easy implementation via u_audio.
By default, capture interface has 48000kHz/2ch
configuration, same as playback channel has.
f_uac1 descriptors naming convention
uses f_uac2 driver naming convention that
makes it more common and meaningful.
Comparing to f_uac1_legacy, the f_uac1 doesn't
have volume/mute functionality. This is because
the f_uac1 volume/mute feature unit was dummy
implementation since that driver creation (2009)
and never had any real volume control or mute
functionality, so there is no any difference
here.
Since f_uac1 functionality, exposed
interface to userspace (virtual ALSA card),
input parameters are so different comparing
to f_uac1_legacy, that there is no any
reason to keep them in the same file/module,
and separate function was created.
g_audio can be built using one of existing
UAC functions (f_uac1, f_uac1_legacy or f_uac2)
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Before introducing new f_uac1 function (with virtual
ALSA card) make current implementation legacy.
This includes renaming of existing files, some
variables, config options and documentation
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
