DMA to variables located on the stack is a bad idea.
For simplicity and to avoid frequent allocations create
a buffer inside the device structure. Protect this
buffer with vendor_req_mutex. Don't protect vendor
requests which don't use this buffer.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When starting a p2p mgmt interface, enable its device role. This
allows us to keep the sta role disabled and scan on the dev role.
In general, p2p management interfaces cannot send vif-specific commands
to FW, as the vif role id is invalid. Only off-channel data and scans
happen on this vif, so most ops are not relevant.
If the vif is a p2p mgmt vif, block some mac80211 ops.
Configure rate policies for p2p mgmt interface, as
otherwise p2p packets come out with arbitrary rates.
Since wpa_supplicant currently doesn't support standalone
p2p device mode (without another attached managed interface),
add p2p device to the allowed interface combinations without
decreasing the allowed station count.
Moreover, increase the station count in some cases, as AP
mode usually starts as station interface, and the AP interface
is now different from the p2p management one).
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add definitions and function prototypes for generic_cfg
command.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for long intervals on sched scan.
If configured, the original request interval will
be used num_short_interval times, and then the
long interval will be used.
While on it, fix the scan command field names
to reflect the expected value is in ms (rather
than secs).
These values will be taken from the conf file,
so bump its version accordingly.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Added support for a new time sync event
the event data contains the WiLink TSF value.
To trigger the event, a HW modification is required,
so as a supporting firmware binary.
Signed-off-by: Yaniv Machani <yanivma@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit d8d2f19feb ("mwifiex: silence TDLS link delete failure
for nonexistent link") lowers the priority of error message when
TDLS link is already deleted. But it had got increased by
commit acebe8c10a ("mwifiex: change dbg print func to
mwifiex_dbg")
Reported-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
kbuild bot reported that commit 592fa228f2 ("ath9k: remove struct
ath_atx_ac") broke the build when CONFIG_ATH9K_STATION_STATISTICS is y.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 592fa228f2 ("ath9k: remove struct ath_atx_ac")
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* Clean ups towards multiple Rx queues
* Add support for longer CMD IDs. This will be required by new
firmwares since we are getting close to the u8 limit.
* bugfixes for the D0i3 power state
* Add basic support for FTM
* More random that doesn't really stand out
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9MX3
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2015-08-04' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* Deprecate -10.ucode
* Clean ups towards multiple Rx queues
* Add support for longer CMD IDs. This will be required by new
firmwares since we are getting close to the u8 limit.
* bugfixes for the D0i3 power state
* Add basic support for FTM
* More random that doesn't really stand out
For PCIe/USB chipsets, preallocated skb buffers are reused for
event handling. mwifiex_check_uap_capabilties() performs
skb_pull(). This patch adds missing skb_push() to restore skb's
data pointer/length.
This bug was introduced by commit debfc60081 ("mwifiex: update
AP WMM settings from BSS_START event")
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
add option to dynamically configure the fw
which debug traces to open
Signed-off-by: Guy Mishol <guym@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Preallocated event SKBs are getting reused for PCIe chipset.
Their physical addresses are shared with firmware so that
firmware can write data into them.
This patch makes sure that SKB is cleared and length is set to
default while submitting it to firmware.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
System crash was observed if one of the driver initialisation
commands is timed out. The reason is our timeout handler triggers
firmware dump, meanwhile driver initialisation error paths have
already freed the adapter structure.
Firmware hasn't yet completely initialized. So collecting firmware
dump is not needed in this case. Command timeout handler is
modified in this patch to fix the crash issue.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When WLAN interface is up and running, driver unload and
load was causing command timeout error.
We enable Rx data by updating RX ring read pointer in
init_fw_port(). It should be done when FW is completely
intialialised. Command timeout is fixed in this patch by
moving init_fw_port() call to mwifiex_init_fw_complete().
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variable pos is u8 here, so memcpy is needed to store u16 aid.
At the same time, aid should be platform independent, upper layer
utility(wpa_supplicant,etc.,) parse it as le16, so keep it le16
here.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
struct ath_atx_ac contains a list of active TIDs belonging to one WMM AC.
This patch changes the code to track active station TIDs in the txq directly.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Setup rxfiler correctly for offchannel ctx.
This fix problem we didn't configure rxfilter, next
didn't receive probe requests and next failed
p2p_find. This was seen when ath9k loaded with
use_chanctx=1
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
While mac80211 setup this per HW, set same
rxfilter configuration for all chanctx.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Advertise p2p device support when ath9k loaded with
use_chanctx=1.
This will fix problem, when first interface is an AP
and next we would like to run p2p_find.
Before p2p find (scan phase) failed with EOPNOTSUPP.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
600f5d909a54("mwifiex: cleanup ioctl wait queue and abstraction layer")
introduced the wakeup_interruptible suppression in mwifiex_complete_cmd
b1a47aa5e1e1("mwifiex: fix system hang issue in cmd timeout error case")
then added wakup_interruptible to mwifiex_cmd_timeout_func the single
place setting a status of ETIMEDOUT.
Instead of doing extra work, using the standard call-chain will have the
same effect:
mwifiex_cancel_pending_ioctl
-> mwifiex_recycle_cmd_node
-> mwifiex_insert_cmd_to_free_q
-> mwifiex_complete_cmd
-> wake_up_interruptible
The difference is that previously the condition was not set to true,
but that's probably just an oversight in b1a47aa5e1 and shouldn't
have any consequence
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
CMD_F_CANCELED was used to abort mwifiex_process_cmdresp in
case it already started or starts processing the cmd.
But this was probably not working the way intended:
- it is racy: mwifiex_process_cmdresp might already have passed that
test and is continuing to use the cmd node being recycled
- mwifiex_process_cmdresp repeatedly uses adapter->curr_cmd which
we just set to NULL
- mwifiex_recycle_cmd_node will clear the flag
The reason why it probably works is that mwifiex_cancel_pending_ioctl
is only called from mwifiex_cmd_timeout_func, where the there is little
chance of a command response still arriving
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex_cancel_pending_ioctl is called only from
mwifiex_cmd_timeout_func. There the wait_q status is set to
-ETIMEDWAIT before calling this function. Whether we reset the status
to -1 or leave it at -ETIMEDWAIT at end doesn't matter since both
are != 0 hence mean failure
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
standard call chain when releasing a cmd node:
mwifiex_recycle_cmd_node
-> mwifiex_insert_cmd_to_free_q
-> mwifiex_complete_cmd, if wait_q_enabled
calling mwifiex_complete_cmd explicitly and setting
wait_q_enabled = false is redundant
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since 1fb654fd97ff("mmc: sdio: add reset callback to bus operations"),
sdio cards can be power cycled using mmc_hw_reset.
The use mmc_remove_host/mmc_add_host is discouraged, because these are
internal functions to the mmc core and should only be used by mmc hosts
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next, they are:
1) A couple of cleanups for the netfilter core hook from Eric Biederman.
2) Net namespace hook registration, also from Eric. This adds a dependency with
the rtnl_lock. This should be fine by now but we have to keep an eye on this
because if we ever get the per-subsys nfnl_lock before rtnl we have may
problems in the future. But we have room to remove this in the future by
propagating the complexity to the clients, by registering hooks for the init
netns functions.
3) Update nf_tables to use the new net namespace hook infrastructure, also from
Eric.
4) Three patches to refine and to address problems from the new net namespace
hook infrastructure.
5) Switch to alternate jumpstack in xtables iff the packet is reentering. This
only applies to a very special case, the TEE target, but Eric Dumazet
reports that this is slowing down things for everyone else. So let's only
switch to the alternate jumpstack if the tee target is in used through a
static key. This batch also comes with offline precalculation of the
jumpstack based on the callchain depth. From Florian Westphal.
6) Minimal SCTP multihoming support for our conntrack helper, from Michal
Kubecek.
7) Reduce nf_bridge_info per skbuff scratchpad area to 32 bytes, from Florian
Westphal.
8) Fix several checkpatch errors in bridge netfilter, from Bernhard Thaler.
9) Get rid of useless debug message in ip6t_REJECT, from Subash Abhinov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for extended command id in triggers handling.
Extended command id header contains group id in addition to command id.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add support for extended firmware event header that contains
a group id as well as the command id.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add support for extended command id in notification system.
Extended command id header contains group id in addition to command id.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This makes various functions in the file rs.c void due to these
functions never returning a error code to signal to their callers
if and how they have failed to complete their intended work.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Move the TX PN assignment (for CCMP only) to the driver. This prepares
the driver for future DSO (driver segmentation offload) where it will
split an SKB into multiple MPDUs by itself.
For TDLS, split out the CCMP TX command handling so that it won't get
a PN assigned, the firmware assigns the PN in that case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Make it similar to reject_tg() in ipt_REJECT.
Suggested-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Hariprasad Shenai says:
====================
add meminfo, bist status and misc. fixes
This patch series adds the following.
Add support to dump memory address range of various hw modules
Add support to dump edc bist status during ecc error
Read correct bits of who am i register for T6 adapter
and update T6 register range
This patch series has been created against net-next tree and includes
patches on cxgb4 and cxgb4vf driver.
We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.
V2: PATCH 3/4 ("cxgb4/cxgb4vf: read the correct bits of PL Who Am I
register") Fix switch statement in get_chip_type() and some more style
fixes based on review comment by Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Read the correct bits of PL Who Am I for the Source PF field which has
changed in T6
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to dump edc bist status for ECC data errors
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add debug support to dump memory address ranges of various hardware
modules of the adapter.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the CSR_DRAM_INIT_TBL_WRITE_POINTER bit wasn't set
on ict reset, in some flows (like disable ict followed by
immediate reset ict) the driver and hardware went out
of sync (the driver cleared the ict_index, while the hw
kept it intact).
Fix it by setting the flag when resetting ict.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Some CSR registers have to be configured also
in case of suspend/resume with unified image
(which doesn't includes reconfiguration flow).
Reuse the existing d3_suspend/d3_resume trans ops,
while making sure some configurations are a bit
different, according to the wowlan type.
After this change, we no longer need the special
wowlan_d0i3 configurations done in iwl_pci_resume,
as they are already being done in the d3_resume op.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
CQM overwrites a few thresholds in the bf command. On the other hand,
when entering D0i3 the thresholds are set to higher values on purpose,
so ignore CQM in this case.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The slow filtering threshold should be higher in D0i3 case.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
TCP software implementation on the host requires extensive computing
power. Offloading even some of the TCP/IP stack to the NIC might save
a significant overhead. In order to enable this feature on our hw,
we need to configure it first. Once done, we mark this capability,
to be advertised later to the OS via ieee80211_register_hw.
The driver Rx indications for TCP Checksum is integrated within the
standard Rx status. The driver responds to those indications as follows:
If the frame was tested by hw and checksum ok report CHECKSUM_UNNECESSARY.
Otherwise, report CHECKSUM_NONE.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware debug infrastructure allows the user to
provide a firmware that will toggle a few registers to
configure the debugging capabilities.
On certain devices, certain operations are forbidden.
Executing a forbidden operation will cause the hardware to
die in a way that only driver unload / load will bring it
back to life.
Fortunately, there is a way to know in advance if those
operations will be accepted by the device. This is where
the new PRPH_BLOCKBIT operation plays its role. If the bit
X from PRPH register Y is set, then we should prevent any
further register configuration. When that happens, drop a
line in the kernel log since this is really an error state:
the user won't have his device configured as he expected.
Add operations that will be used in the future:
INDIRECT_ASSIGN, INDIRECT_SETBIT, and INDIRECT_CLEARBIT.
Other debugging configurations (such as destination
configuration for the monitor) will take place in any case.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In iwl_mvm_tx_skb_non_sta(), in case of managed interface,
use the AP station for multicast frames instead of the auxiliary
station as otherwise the frames can be sent to an absent P2P GO as
the FW does not block transmissions for the auxiliary station
since it is not associated with the station MAC context.
Note that this is not possible for unicast frames, as a TDLS
discovery response is sent without a station entry, and in this
case the P2P GO NoA should not block transmission to the peer.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Allow the transport layer to return an error upon suspend.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This reverts commit 088070a2f6.
When working in d0i3_on_idle mode, we explicitly go out
of d0i3 on resume (so other potential commands could
be sent).
However, D0I3_DEFER_WAKEUP is currently cleared on
resume complete (which happens only later on), causing
d0i3 exit to timeout.
Since mac80211 was modified to accept incoming frames
once drv_resume was called, we can safely revert this
patch, and handle the pending work on iwl_mvm_resume().
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
